There are 2 Type-c PHYs in RK3399, but only one DP controller. Hence
only one PHY can connect to DP controller at one time, the other should
be disconnected. The GRF_SOC_CON26 register has a switch bit to do it,
set this bit means enable PHY 1, clear this bit means enable PHY 0.
If the board has 2 Type-C ports, the DP driver get the phy id from
devm_of_phy_get_by_index, and then control this switch according to
this id. But some others board only has one Type-C port, it may be PHY 0
or PHY 1. The dts node id can not tell us the correct PHY id. Hence move
this switch to PHY driver, the PHY driver can distinguish between PHY 0
and PHY 1, and then write the correct register bit.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[The phy-changes are in the phy-tree now and the cdn-dp wasn't
enabled at all so far, so this change can go through drm-misc
alone without causing issues when testing drm-misc]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180216120956.19034-6-enric.balletbo@collabora.com
drm_printk is used for both DRM_ERROR and DRM_DEBUG with unnecessary
arguments that can be removed by creating separate functins.
Create specific functions for these calls to reduce x86/64 defconfig
size by ~20k.
Modify the existing macros to use the specific calls.
new:
$ size -t drivers/gpu/drm/built-in.a | tail -1
1876562 44542 995 1922099 1d5433 (TOTALS)
old:
$ size -t drivers/gpu/drm/built-in.a | tail -1
1897565 44542 995 1943102 1da63e (TOTALS)
Miscellanea:
o intel_display requires a change to use the specific calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/016b5cb84cede20fd0f91ed6965421d99fd5f2ce.1520978414.git.joe@perches.com
The cable_plugin member never receives an assignment, so it is always
false, which causes hdmi_enable_overflow_interrupts() to never
be called as per the logic below:
if (hdmi->cable_plugin && hdmi->sink_is_hdmi)
hdmi_enable_overflow_interrupts(hdmi);
This has been the case since the driver was originally introduced
in commit 9aaf880ed4 ("imx-drm: Add mx6 hdmi transmitter support").
Remove the cable_plugin element and the hdmi_enable_overflow_interrupts()
function that is never called.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # On R-Car H3
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1518812170-22687-1-git-send-email-festevam@gmail.com
This patch replace instances of drm_framebuffer_unreference with _put()
suffix, because it is shorter and consistent with the kernel use of
*_get/put() suffixes.
This was done with the following Coccinelle script:
@r@
expression e;
@@
(
-drm_framebuffer_reference(e);
+drm_framebuffer_get(e);
|
-drm_framebuffer_unreference(e);
+drm_framebuffer_put(e);
)
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Acked-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180311233313.GA19721@Haneen
The rockchip DRM driver is quite careful to disable interrupts
when taking a lock that is also taken in interrupt context,
which is a good thing.
What is a bit over the top is to use spin_lock_irqsave when
already in interrupt context, as you cannot take another
interrupt again, and disabling interrupt is just pure
overhead.
Switching to the non _irqsave version in interrupt context is
more logical, and less heavy handed.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220130120.5254-4-marc.zyngier@arm.com
memcpy is only meant to be used for memory, and only that.
MMIO accessors should be used to access MMIO regions, preferably
the ones that correspond to the size of the register accessed.
Let's convert the bulk register copy to writel/readl_relaxed,
which is the correct API.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220130120.5254-3-marc.zyngier@arm.com
Calling request_irq() followed by disable_irq() is usually a bad idea,
specially if the interrupt can be pending, and you're not yet in a
position to handle it.
This is exactly what happens on my kevin system when rebooting in a
second kernel using kexec: Some interrupt is left pending from
the previous kernel, and we take it too early, before disable_irq()
could do anything.
Let's clear the pending interrupts as we initialize the HW, and move
the interrupt request after that point. This ensures that we're in
a sane state when the interrupt is requested.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[adapted to recent rockchip-drm changes]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220130120.5254-2-marc.zyngier@arm.com
We currently wait for the panel to mirror our intended PSR state
before continuing on both PSR enter and PSR exit. This is really
only important to do when we're entering PSR, since we want to
be sure the last frame we pushed is being served from the panel's
internal fb before shutting down the soc blocks (vop/analogix).
This patch changes the behavior such that we only wait for the
panel to complete the PSR transition when we're entering PSR, and
to skip verification when we're exiting.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-7-enric.balletbo@collabora.com
Like many other panel drivers, this one fails to build when backlight
support is disabled:
drivers/gpu/drm/panel/panel-raydium-rm68200.o: In function `rm68200_probe':
panel-raydium-rm68200.c:(.text+0x14a): undefined reference to `devm_of_find_backlight'
This adds the appropriate dependency.
Note that while include/linux/backlight.h provides a stub inline when
backlight support is not enabled, this isn't enough to deal with the
case where backlight support is built as a module but the panel driver
is built-in, in which case linking will still fail as above.
One way to avoid this is to add a dependency such as this:
depends on BACKLIGHT_CLASS_DEVICE || BACKLIGHT_CLASS_DEVICE=n
but that is rather complex and misses the point that the panel support
is mostly useless without backlight support.
Fixes: 2b7ed18bed ("drm/panel: Add support for Raydium RM68200 panel driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[treding@nvidia.com: clarify the need for the dependency]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180313210015.3344380-1-arnd@arndb.de
Add a lock to vop to avoid disabling the crtc while waiting for a line
flag while enabling psr. If we disable in the middle of waiting for the
line flag, we'll end up timing out or worse.
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-5-enric.balletbo@collabora.com
We would meet a short black screen when exit PSR with the full link
training, In this case, we should use fast link train instead of full
link training.
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
[dropped header reordering]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-6-enric.balletbo@collabora.com
There is a race between AUX CH bring-up and enabling bridge which will
cause link training to fail. To avoid hitting it, don't change psr state
while enabling the bridge.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
[seanpaul fixed up the commit message a bit and renamed *_supported to *_enabled]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-4-enric.balletbo@collabora.com
Now that the spinlocks and timers are gone, we can remove the psr
worker located in rockchip's analogix driver and do the enable/disable
directly. This should simplify the code and remove races on disable.
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-3-enric.balletbo@collabora.com
Make sure the request PSR state takes effect in analogix_dp_send_psr_spd()
function, or print the sink PSR error state if we failed to apply the
requested PSR setting.
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
[seanpaul changed timeout loop to a readx poll]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-2-enric.balletbo@collabora.com
Handle both positive and negative dclk polarity,
according to bus_flags, taking care of this:
On A20 and similar SoCs, the only way to achieve Positive Edge
(Rising Edge), is setting dclk clock phase to 2/3(240°).
By default TCON works in Negative Edge(Falling Edge), this is why phase
is set to 0 in that case.
Unfortunately there's no way to logically invert dclk through IO_POL
register.
The only acceptable way to work, triple checked with scope,
is using clock phase set to 0° for Negative Edge and set to 240° for
Positive Edge.
On A33 and similar SoCs there would be a 90° phase option, but it divides
also dclk by 2.
This patch is a way to avoid quirks all around TCON and DOTCLOCK drivers
for using A33 90° phase divided by 2 and consequently increase code
complexity.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520963677-124239-1-git-send-email-giulio.benetti@micronovasrl.com
mode_valid function must be connected to encoder.
Otherwise it could get not be called by drm in the case there's a
bridge connected to encoder instead of a panel.
Move mode_valid function pointer to encoder helper functions,
changing its prototype according to encoder helper function pointer.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520941017-81177-1-git-send-email-giulio.benetti@micronovasrl.com
Commit 5addcf0a5f ("nouveau: add runtime PM support (v0.9)") prevents
runtime suspend of the GPU if its integrated HDA controller is not bound
to a driver. The rationale appears to be that probing the HDA fails if
the GPU is in D3cold.
However we now use a device link to ensure that the GPU is runtime
resumed while the HDA controller is probed, rendering this safety
measure obsolete. Remove it.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/77e0ab74f3377ea9b6acf8fab624acfb4f7dbeca.1520068884.git.lukas@wunner.de
Back in 2013, runtime PM for GPUs with integrated HDA controller was
introduced with commits 0d69704ae3 ("gpu/vga_switcheroo: add driver
control power feature. (v3)") and 246efa4a07 ("snd/hda: add runtime
suspend/resume on optimus support (v4)").
Briefly, the idea was that the HDA controller is forced on and off in
unison with the GPU.
The original code is mostly still in place even though it was never a
100% perfect solution: E.g. on access to the HDA controller, the GPU
is powered up via vga_switcheroo_runtime_resume_hdmi_audio() but there
are no provisions to keep it resumed until access to the HDA controller
has ceased: The GPU autosuspends after 5 seconds, rendering the HDA
controller inaccessible.
Additionally, a kludge is required when hda_intel.c probes: It has to
check whether the GPU is powered down (check_hdmi_disabled()) and defer
probing if so.
However in the meantime (in v4.10) the driver core has gained a feature
called device links which promises to solve such issues in a clean way:
It allows us to declare a dependency from the HDA controller (consumer)
to the GPU (supplier). The PM core then automagically ensures that the
GPU is runtime resumed as long as the HDA controller's ->probe hook is
executed and whenever the HDA controller is accessed.
By default, the HDA controller has a dependency on its parent, a PCIe
Root Port. Adding a device link creates another dependency on its
sibling:
PCIe Root Port
^ ^
| |
| |
HDA ===> GPU
The device link is not only used for runtime PM, it also guarantees that
on system sleep, the HDA controller suspends before the GPU and resumes
after the GPU, and on system shutdown the HDA controller's ->shutdown
hook is executed before the one of the GPU. It is a complete solution.
Using this functionality is as simple as calling device_link_add(),
which results in a dmesg entry like this:
pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
The code for the GPU-governed audio power management can thus be removed
(except where it's still needed for legacy manual power control).
The device link is added in a PCI quirk rather than in hda_intel.c.
It is therefore legal for the GPU to runtime suspend to D3cold even if
the HDA controller is not bound to a driver or if CONFIG_SND_HDA_INTEL
is not enabled, for accesses to the HDA controller will cause the GPU to
wake up regardless if they're occurring outside of hda_intel.c (think
config space readout via sysfs).
Contrary to the previous implementation, the HDA controller's power
state is now self-governed, rather than GPU-governed, whereas the GPU's
power state is no longer fully self-governed. (The HDA controller needs
to runtime suspend before the GPU can.)
It is thus crucial that runtime PM is always activated on the HDA
controller even if CONFIG_SND_HDA_POWER_SAVE_DEFAULT is set to 0 (which
is the default), lest the GPU stays awake. This is achieved by setting
the auto_runtime_pm flag on every codec and the AZX_DCAPS_PM_RUNTIME
flag on the HDA controller.
A side effect is that power consumption might be reduced if the GPU is
in use but the HDA controller is not, because the HDA controller is now
allowed to go to D3hot. Before, it was forced to stay in D0 as long as
the GPU was in use. (There is no reduction in power consumption on my
Nvidia GK107, but there might be on other chips.)
The code paths for legacy manual power control are adjusted such that
runtime PM is disabled during power off, thereby preventing the PM core
from resuming the HDA controller.
Note that the device link is not only added on vga_switcheroo capable
systems, but for *any* GPU with integrated HDA controller. The idea is
that the HDA controller streams audio via connectors located on the GPU,
so the GPU needs to be on for the HDA controller to do anything useful.
This commit implicitly fixes an unbalanced runtime PM ref upon unbind of
hda_intel.c: On ->probe, a runtime PM ref was previously released under
the condition "azx_has_pm_runtime(chip) || hda->use_vga_switcheroo", but
on ->remove a runtime PM ref was only acquired under the first of those
conditions. Thus, binding and unbinding the driver twice on a
vga_switcheroo capable system caused the runtime PM refcount to drop
below zero. The issue is resolved because the AZX_DCAPS_PM_RUNTIME flag
is now always set if use_vga_switcheroo is true.
For more information on device links please refer to:
https://www.kernel.org/doc/html/latest/driver-api/device_link.html
Documentation/driver-api/device_link.rst
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress
Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/51bd38360ff502a8c42b1ebf4405ee1d3f27118d.1520068884.git.lukas@wunner.de
This patch adds support for DMT display modes over HDMI.
The modes timings configurations are from the Amlogic Vendor linux tree
and tested over multiples monitors.
Previously only a selected number of CEA modes were supported.
Only these following modes are supported with these changes:
- 640x480@60Hz
- 800x600@60Hz
- 1024x768@60Hz
- 1152x864@75Hz
- 1280x1024@60Hz
- 1600x1200@60Hz
- 1920x1080@60Hz
The associated code to handle the clock rates is also added.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520935670-14187-1-git-send-email-narmstrong@baylibre.com
This patch adds support for AUO G104SN02 V2 800x600 10.4" panel to DRM
simple panel driver.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1513430016.1930.4.camel@googlemail.com
Fixes the following sparse warnings:
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:182:12: warning:
symbol 'ili9322_inputs' was not declared. Should it be static?
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:343:28: warning:
symbol 'ili9322_regmap_config' was not declared. Should it be static?
Also change ili9322_inputs to 'const char * const' to avoid
chackpatch warning.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1514948938-19996-1-git-send-email-weiyongjun1@huawei.com
Add support for the optional power-supply.
Note: A "dummy regulator" is returned by devm_regulator_get()
if the optional regulator is not present in the device tree,
simplifying the source code when enabling/disabling the regulator.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205094532.23547-3-philippe.cornu@st.com
Convert the sharp lq123p1jx31 from using a fixed mode to specifying a
display timing with min/typ/max values. This allows us to capture the
timings set forth in the datasheet as well as the additional values that
we've cleared with the display vendor to avoid interference with the
digitizer on the Samsung Chromebook Plus (kevin).
A follow-on patch will specify the override mode for kevin devices.
Changes in v2:
- None
Changes in v3:
- None
Cc: Doug Anderson <dianders@chromium.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180208174855.55620-6-seanpaul@chromium.org
This fixes bad color output. When I was first testing the device I
had the DPI hardware set to 666 mode, but apparently in the refactor
to use the bus_format information from the panel driver, I failed to
actually update the panel.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: e8b6f561b2 ("drm/panel: simple: Add the 7" DPI panel from Adafruit")
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309233332.1769-1-eric@anholt.net
Using the hint from the plane state, we turn on the background color
to avoid display corruption from planes blending with the background.
Changes from v1:
- Use needs_bg_fill from plane state
Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1520556817-97297-5-git-send-email-stschake@gmail.com
Considering a single plane only, we have to enable background color
when the plane has an alpha format and could be blending from the
background or when it doesn't cover the entire screen.
Changes from v1:
- Drop unrelated change
- Move needs_bg_fill to plane state
Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1520556817-97297-3-git-send-email-stschake@gmail.com
Alpha formats in DRM are assumed to be premultiplied, so we should be
setting the PREMULT bit in the plane configuration for HVS.
Changes from v1:
- Use correct has_alpha
Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1520556817-97297-2-git-send-email-stschake@gmail.com
Instead of using timer and spinlocks, use delayed_work and
mutexes for rockchip psr. This allows us to make blocking
calls when enabling/disabling psr (which is sort of important
given we're talking over dpcd to the display).
Cc: Caesar Wang <wxt@rock-chips.com>
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305222324.5872-3-enric.balletbo@collabora.com
There's a race between when bridge_disable and when vop_crtc_disable
are called. If the flush timer triggers a new psr work between these,
we will operate eDP without power shutdowned by bridge_disable. In this
case, moving activate/deactivate to enable/disable bridge to avoid it.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305222324.5872-2-enric.balletbo@collabora.com
The HDMI vpll clock should be enabled when bind() is called. So move the
clk_prepare_enable of that clock to bind() function and add the missing
clk_disable_unprepare() required in error handling path and unbind().
Fixes: 12b9f204e8 ("drm: bridge/dw_hdmi: add rockchip rk3288 support")
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302175757.28192-5-enric.balletbo@collabora.com
In bind the clk_prepare_enable of the HDMI pclk is called before adding the
i2c_adapter. So it should be the other way around in unbind, first remove
the i2c_adapter and then call the clk_disable_unprepare.
Fixes: 412d4ae6b7 ("drm/rockchip: hdmi: add Innosilicon HDMI support")
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302175757.28192-4-enric.balletbo@collabora.com
In bind()'s error handling path call destroy functions instead of
cleanup functions for encoder and connector and reorder to match how is
called in bind().
In unbind() call the connector and encoder destroy functions.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302175757.28192-2-enric.balletbo@collabora.com
Replace the ad-hoc iturbt_709 property with the new standard
COLOR_ENCODING property. Compiles, but not tested.
v2: Fix typos (Ilia)
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: nouveau@lists.freedesktop.org
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180220134816.15229-1-ville.syrjala@linux.intel.com
Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu>
Acked-by: Ben Skeggs <bskeggs@redhat.com> #irc
We were previously selecting 1024x768 and 32BPP as the default
set-up for the PL111 consumers.
This does not work on elder systems: the device tree bindings
support a property "max-memory-bandwidth" in bytes/second that
states that if you exceed this the memory bus will saturate.
The result is flickering and unstable images.
Parse the "max-memory-bandwidth" and respect it when
intializing the driver. On the RealView PB11MP, Versatile and
Integrator/CP we get a nice console as default with this code.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307215819.15814-1-linus.walleij@linaro.org
The following happens when connection a DVI output driven
from the SiI9022 using a DVI-to-VGA adapter plug:
i2c i2c-0: sendbytes: NAK bailout.
i2c i2c-0: sendbytes: NAK bailout.
Then no picture. Apparently the I2C engine inside the SiI9022
is not smart enough to try to fall back to DDC I2C. Or the
vendor have not integrated the electronics properly. I don't
know which one it is.
After this, the I2C bus seems stalled and the first attempt to
read the status register fails, and the code returns with
negative return value, and the display fails to initialized.
Instead, retry status readout five times and continue even
if this fails.
Tested on the ARM Versatile Express with a DVI-to-VGA
connector, it now gives picture.
Introduce a helper struct device *dev variable to make
the code more readable.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305101702.13441-1-linus.walleij@linaro.org
We want to cut down the default bpp to 16 on the RealView so
we can have a 1024x768 framebuffer console by default. The
memory bandwidth limitations makes this not work with the
PL111 default of 32bpp.
This builds on top of the earlier patches making the
framebuffer default bpp a per-variant variable.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302090948.6399-4-linus.walleij@linaro.org
Pimp drm_property_type_valid() to check for more fails with the
property flags. Also make the check before adding the property,
and bail out if things look bad.
Since we're now chekcing for more than the type let's also
change the function name to drm_property_flags_valid().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306164849.2862-6-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
