Starting with R-Car H3 ES2.0, the parent of RCLK is selected using MD28.
Add support for that, but retain the old behavior for R-Car H3 ES1.x and
M3-W ES1.0 using a quirk.
Inspired by a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
The Clock Pulse Generator / Module Standby and Software Reset module in
R-Car H3 ES2.0 differs from ES1.x in the following areas:
- More core clocks (S0D2, S0D3, S0D6, S0D8, S0D12),
- Different parent clocks for AUDMAC, EtherAVB, FCP, FDP, IMR,
SYS-DMAC, VIN, VSPB, VSPI,
- Removal of modules CSI21, FCPCI, FCPF2, FCPVD3, FCPVI2, FDP1-2,
USB3-IF1, VSPD3, VSPI2,
- Addition of modules EHCI3, HS-USB-IF3, USB-DMAC3-0, USB-DMAC3-1.
The goal is twofold:
1. Support both the ES1.x and ES2.0 SoC revisions in a single binary
for now,
2. Make it clear which code supports ES1.x, so it can easily be
identified and removed later, when production SoCs are deemed
ubiquitous.
This is achieved by:
- Updating the clock tables for the latest revision (ES2.0), but not
removing clocks that only exist on earlier revisions (ES1.x),
- Detecting the SoC revision at runtime using the new soc_device_match()
API, and fixing up the clocks tables to match the actual SoC
revision, by:
- NULLifying core and module clocks of modules that do not exist,
- Reparenting module clocks that have a different parent on ES1.x.
Based on R-Car Gen3 Hardware User's Manual rev. 0.53E.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The same SoC may have different clocks and/or module clock parents,
depending on SoC revision. One option is to use different sets of clock
tables for each SoC revision. However, if the differences are small, it
is much more space-efficient to have a single set of clock tables, and
fix those up at runtime instead.
Hence provide three helpers:
- Two helpers to NULLify core and module clocks that do not exist on
some revisions (NULLified clocks are skipped during the registration
phase),
- One helper to reparent module clocks that have different clock
parents.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a workaround for errata on R-Car H3 ES1.0, where the PLL0, PLL2, and
PLL4 clock frequencies are off by a factor of two.
Inspired by a patch by Dien Pham in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Dien Pham <dien.pham.ry@renesas.com>
Pass the mode pin states from the SoC-specific CPG/MSSR driver to the
R-Car Gen3 CPG driver core, as their state will be needed to make some
core clock configuration decisions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The parent clock of the Audio DMACs is the "ZS" AXI bus clock, which
maps to S3D1 on R-Car H3 ES1.x.
All module clocks must be sorted by clock ID.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Add the IMR[0-3] clocks to the R8A7795 CPG/MSSR driver.
Based on the original (and large) patch by Konstantin Kozhevnikov
<Konstantin.Kozhevnikov@cogentembedded.com>.
Signed-off-by: Konstantin Kozhevnikov <Konstantin.Kozhevnikov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When there is no status bit, it is possible for the clock enable/disable
operation to have not completed by the time the driver code resumes
execution. This is due to the fact that write operations are sometimes
queued and delayed internally. Doing a read ensures the write operations
has completed.
Fixes: b6face404f ("ARM: shmobile: r7s72100: add essential clock nodes to dtsi")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- Use CLK_IS_CRITICAL to handle critical clocks,
- Add Reset Control Support for R-Car Gen2 and Gen3, and RZ/G1,
- Add IIC-DVFS clocks for R-Car H3 and M3-W,
- Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WluB
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Use CLK_IS_CRITICAL to handle critical clocks,
- Add Reset Control Support for R-Car Gen2 and Gen3, and RZ/G1,
- Add IIC-DVFS clocks for R-Car H3 and M3-W,
- Minor cleanups.
* tag 'clk-renesas-for-v4.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add IIC-DVFS clock
clk: renesas: r8a7795: Add IIC-DVFS clock
clk: renesas: cpg-mssr: Add support for reset control
clk: renesas: cpg-mssr: Rename cpg_mssr_priv.mstp_lock
clk: renesas: cpg-mssr: Document suitability for RZ/G1
dt-bindings: clock: renesas: cpg-mssr: Document reset control support
clk: renesas: mstp: Reformat cpg_mstp_clock_register() for git diff
clk: renesas: mstp: Make INTC-SYS a critical clock
clk: renesas: cpg-mssr: Migrate to CLK_IS_CRITICAL
Add optional support for the Reset Control feature of the Renesas Clock
Pulse Generator / Module Standby and Software Reset module on R-Car
Gen2, R-Car Gen3, and RZ/G1 SoCs.
This allows to reset SoC devices using the Reset Controller API.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The spinlock is used to protect Read-Modify-Write register accesses,
which won't be limited to SMSTPCR register accesses.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
The Renesas CPG/MSSR driver is already in active use for RZ/G1 since
commits c0b2d75d2a ("clk: renesas: cpg-mssr: Add R8A7743 support")
and 9127d54bb8 ("clk: renesas: cpg-mssr: Add R8A7745 support").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
As the function header of cpg_mstp_clock_register() is split in an
unusual way, "git diff" gets confused when changes to the body of
the function are made, and attributes them to the wrong function.
Reformat the function header to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
INTC-SYS is the module clock for the GIC. Accessing the GIC while it is
disabled causes:
Unhandled fault: asynchronous external abort (0x1211) at 0x00000000
Currently, the GIC-400 driver cannot enable its module clock for several
reasons:
- It does not use a platform device, so Runtime PM is not an option,
- gic_of_init() runs before any clocks are registered, so it cannot
enable the clock explicitly,
- gic_of_init() cannot return -EPROBE_DEFER, as IRQCHIP_DECLARE()
doesn't support deferred probing.
Hence we have to keep on relying on the boot loader for enabling the
module clock.
To prevent the module clock from being disabled when the CCF core thinks
it is unused, and thus causing a system lock-up, add a check to the MSTP
clock driver and enable CLK_IS_CRITICAL. This will make sure the module
clock is never disabled.
This is a hard dependency for describing the INTC-SYS clock in DT on
R-Mobile APE6 and R-Car Gen2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
When the Renesas CPG/MSSR driver was introduced, it was anticipated that
critical clocks would be handled through a new CLK_ENABLE_HAND_OFF flag
soon. However, CLK_ENABLE_HAND_OFF never made it upstream.
Instead, commit 32b9b10961 ("clk: Allow clocks to be marked as
CRITICAL") introduced CLK_IS_CRITICAL, a flag with slightly differing
semantics. Still, it can be used to prevent e.g. the GIC module clock
from being turned off, until the GIC-400 driver has full support for
Runtime PM.
Hence migrate the Renesas CPG/MSSR driver from CLK_ENABLE_HAND_OFF to
CLK_IS_CRITICAL.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/A1 is different than the other Renesas SOCs because the MSTP
registers are 8-bit instead of 32-bit and if you try writing values as
32-bit nothing happens...meaning this driver never worked for r7s72100.
Fixes: b6face404f ("ARM: shmobile: r7s72100: add essential clock nodes to dtsi")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add RZ/G1E (R8A7745) Clock Pulse Generator / Module Standby and Software
Reset support, using the CPG/MSSR driver core and the common R-Car Gen2
(and RZ/G) code.
Based on the proof-of-concept R8A7791 CPG/MSSR patch by Geert
Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add RZ/G1M (R8A7743) Clock Pulse Generator / Module Standby and Software
Reset support, using the CPG/MSSR driver core and the common R-Car Gen2
(and RZ/G) code.
Based on the proof-of-concept R8A7791 CPG/MSSR patch by Geert
Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the common R-Car Gen2 (and RZ/G) Clock Pulse Generator / Module
Standby and Software Reset support code, using the CPG/MSSR driver
core.
Based on the proof-of-concept R8A7791 CPG/MSSR patch by Geert
Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Correct HDMI parent clock so that the rate of the
HDMI clock is 1/4 rather than 1/2 of the rate of PLL1
as per the v0.52 (Jun, 15) manual.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All R-Car Gen3 clock drivers now obtain the values of the mode pins from
the R-Car RST driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Obtain the values of the mode pins from the R-Car RST driver, which
relies on the presence in DT of a device node for the RST module.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Obtain the values of the mode pins from the R-Car RST driver, which
relies on the presence in DT of a device node for the RST module.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Obtain the values of the mode pins from the R-Car RST driver, which
relies on the presence in DT of a device node for the RST module.
Fall back to our own private copy of rcar_gen2_read_mode_pins() for
backward-compatibility with old DTs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Obtain the values of the mode pins from the R-Car RST driver, which
relies on the presence in DT of a device node for the RESET/WDT module.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Obtain the values of the mode pins from the R-Car RST driver, which
relies on the presence in DT of a device node for the RESET/WDT module.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
The intention was to enable the checks if debugging is enabled, not
disabled.
Fixes: f793d1e517 ("clk: shmobile: Add new CPG/MSSR driver core")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
