In order to dump the FECs registers the clocks have to be ticking,
otherwise a data abort occurs. Add calls to runtime PM so they are
enabled and later disabled.
Fixes: e8fcfcd568 ("net: fec: optimize the clock management to save power")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before ip_tunnel_ecn_encap() and udp_tunnel_xmit_skb() we should filter
tos value by RT_TOS() instead of using config tos directly.
vxlan_get_route() would filter the tos to fl4.flowi4_tos but we didn't
return it back, as geneve_get_v4_rt() did. So we have to use RT_TOS()
directly in function ip_tunnel_ecn_encap().
Fixes: 206aaafcd2 ("VXLAN: Use IP Tunnels tunnel ENC encap API")
Fixes: 1400615d64 ("vxlan: allow setting ipv6 traffic class")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables 'window_interval' is u64 and do_div()
truncates it to 32 bits, which means it can test
non-zero and be truncated to zero for division.
The unit of window_interval is nanoseconds,
so its lower 32-bit is relatively easy to exceed.
Fix this issue by using div64_u64() instead.
Fixes: 7298de9cd7 ("sch_cake: Add ingress mode")
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: cake@lists.bufferbloat.net
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8243186f0c ("fs: remove ksys_dup()") and the
subsequent fix for it in commit 2d3145f8d2 ("early init: fix error
handling when opening /dev/console").
Trying to use filp_open() and f_dupfd() instead of pseudo-syscalls
caused more trouble than what is worth it: it requires accessing vfs
internals and it turns out there were other bugs in it too.
In particular, the file reference counting was wrong - because unlike
the original "open+2*dup" sequence it used "filp_open+3*f_dupfd" and
thus had an extra leaked file reference.
That in turn then caused odd problems with Androidx86 long after boot
becaue of how the extra reference to the console kept the session active
even after all file descriptors had been closed.
Reported-by: youling 257 <youling257@gmail.com>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc produces a variable may be uninitialized warning for "val" in
parse_entry(). This is really a false positive, but the code is subtle
enough to just initialize val to zero and it's not a fast path to worry
about it.
Marked for stable to remove the warning in the stable trees as well.
Cc: stable@vger.kernel.org
Fixes: 6c3edaf9fd ("tracing: Introduce trace event injection")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
When we receive a D-SACK, where the sequence number satisfies:
undo_marker <= start_seq < end_seq <= prior_snd_una
we consider this is a valid D-SACK and tcp_is_sackblock_valid()
returns true, then this D-SACK is discarded as "old stuff",
but the variable first_sack_index is not marked as negative
in tcp_sacktag_write_queue().
If this D-SACK also carries a SACK that needs to be processed
(for example, the previous SACK segment was lost), this SACK
will be treated as a D-SACK in the following processing of
tcp_sacktag_write_queue(), which will eventually lead to
incorrect updates of undo_retrans and reordering.
Fixes: fd6dad616d ("[TCP]: Earlier SACK block verification & simplify access to them")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_port_set_cmode() relies on cmode stored in struct
mv88e6xxx_port to skip cmode update when the requested value matches the
cached value. It turns out that mv88e6xxx_port_hidden_write() might
change the port cmode setting as a side effect, so we can't rely on the
cached value to determine that cmode update in not necessary.
Force cmode update in mv88e6341_port_set_cmode(), to make
serdes configuration work again. Other mv88e6xxx_port_set_cmode()
callers keep the current behaviour.
This fixes serdes configuration of the 6141 switch on SolidRun Clearfog
GT-8K.
Fixes: 7a3007d22e ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that randconfig builds with gcc no longer produce a lot of
ccache hits, unlike with clang, and traced this back to plugins
now being enabled unconditionally if they are supported.
I am now working around this by adding
export CCACHE_COMPILERCHECK=/usr/bin/size -A %compiler%
to my top-level Makefile. This changes the heuristic that ccache uses
to determine whether the plugins are the same after a 'make clean'.
However, it also seems that being able to just turn off the plugins is
generally useful, at least for build testing it adds noticeable overhead
but does not find a lot of bugs additional bugs, and may be easier for
ccache users than my workaround.
Fixes: 9f671e5815 ("security: Create "kernel hardening" config area")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20191211133951.401933-1-arnd@arndb.de
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
This adds logic to the user_notification_basic test to set a member
of struct seccomp_notif to an invalid value to ensure that the kernel
returns EINVAL if any of the struct seccomp_notif members are set to
invalid values.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Suggested-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191230203811.4996-1-sargun@sargun.me
Fixes: 6a21cc50f0 ("seccomp: add a return code to trap to userspace")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
This patch is a small change in enforcement of the uapi for
SECCOMP_IOCTL_NOTIF_RECV ioctl. Specifically, the datastructure which
is passed (seccomp_notif) must be zeroed out. Previously any of its
members could be set to nonsense values, and we would ignore it.
This ensures all fields are set to their zero value.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com>
Reviewed-by: Aleksa Sarai <cyphar@cyphar.com>
Acked-by: Tycho Andersen <tycho@tycho.ws>
Link: https://lore.kernel.org/r/20191229062451.9467-2-sargun@sargun.me
Fixes: 6a21cc50f0 ("seccomp: add a return code to trap to userspace")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
The seccomp_notif structure should be zeroed out prior to calling the
SECCOMP_IOCTL_NOTIF_RECV ioctl. Previously, the kernel did not check
whether these structures were zeroed out or not, so these worked.
This patch zeroes out the seccomp_notif data structure prior to calling
the ioctl.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Reviewed-by: Tycho Andersen <tycho@tycho.ws>
Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191229062451.9467-1-sargun@sargun.me
Fixes: 6a21cc50f0 ("seccomp: add a return code to trap to userspace")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
The sizes by which seccomp_notif and seccomp_notif_resp are allocated are
based on the SECCOMP_GET_NOTIF_SIZES ioctl. This allows for graceful
extension of these datastructures. If userspace zeroes out the
datastructure based on its version, and it is lagging behind the kernel's
version, it will end up sending trailing garbage. On the other hand,
if it is ahead of the kernel version, it will write extra zero space,
and potentially cause corruption.
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Suggested-by: Tycho Andersen <tycho@tycho.ws>
Link: https://lore.kernel.org/r/20191230203503.4925-1-sargun@sargun.me
Fixes: fec7b66905 ("samples: add an example of seccomp user trap")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
The ram_core.c routines treat przs as circular buffers. When writing a
new crash dump, the old buffer needs to be cleared so that the new dump
doesn't end up in the wrong place (i.e. at the end).
The solution to this problem is to reset the circular buffer state before
writing a new Oops dump.
Signed-off-by: Aleksandr Yashkin <a.yashkin@inango-systems.com>
Signed-off-by: Nikolay Merinov <n.merinov@inango-systems.com>
Signed-off-by: Ariel Gilman <a.gilman@inango-systems.com>
Link: https://lore.kernel.org/r/20191223133816.28155-1-n.merinov@inango-systems.com
Fixes: 896fc1f0c4 ("pstore/ram: Switch to persistent_ram routines")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Augmented Power Delivery Objects (A)PDO_s are used by USB-C
PD power adapters to advertize the voltages and currents
they support. There can be up to 7 PDO_s but before PPS
(programmable power supply) there were seldom more than 4
or 5. Recently Samsung released an optional PPS 45 Watt power
adapter (EP-TA485) that has 7 PDO_s. It is for the Galaxy 10+
tablet and charges it quicker than the adapter supplied at
purchase. The EP-TA485 causes an overzealous WARN_ON to soil
the log plus it miscalculates the number of bytes to read.
So this bug has been there for some time but goes
undetected for the majority of USB-C PD power adapters on
the market today that have 6 or less PDO_s. That may soon
change as more USB-C PD adapters with PPS come to market.
Tested on a EP-TA485 and an older Lenovo PN: SA10M13950
USB-C 65 Watt adapter (without PPS and has 4 PDO_s) plus
several other PD power adapters.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191230033544.1809-1-dgilbert@interlog.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current GPL v2.0 or later SPDX tag is 'GPL-2.0-or-later' as defined
at https://spdx.org/licenses/.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Under load, the RX side of the mscan driver can get stuck while TX still
works. Restarting the interface locks up the system. This behaviour
could be reproduced reliably on a MPC5121e based system.
The patch fixes the return value of the NAPI polling function (should be
the number of processed packets, not constant 1) and the condition under
which IRQs are enabled again after polling is finished.
With this patch, no more lockups were observed over a test period of ten
days.
Fixes: afa17a500a ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Florian Faber <faber@faberman.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: aec5fb2268 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Cc: stable <stable@vger.kernel.org> # 4.19
Cc: Jimmy Assarsson <extja@kvaser.com>
Cc: Christer Beskow <chbe@kvaser.com>
Cc: Nicklas Johansson <extnj@kvaser.com>
Cc: Martin Henriksson <mh@kvaser.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
KMSAN sysbot detected a read access to an untinitialized value in the
headroom of an outgoing CAN related sk_buff. When using CAN sockets this
area is filled appropriately - but when using a packet socket this
initialization is missing.
The problematic read access occurs in the CAN receive path which can
only be triggered when the sk_buff is sent through a (virtual) CAN
interface. So we check in the sending path whether we need to perform
the missing initializations.
Fixes: d3b58c47d3 ("can: replace timestamp as unique skb attribute")
Reported-by: syzbot+b02ff0707a97e4e79ebb@syzkaller.appspotmail.com
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.1
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix inconsistent IS_ERR and PTR_ERR in tcan4x5x_parse_config().
The proper pointer to be passed as argument is tcan4x5x->device_wake_gpio.
This bug was detected with the help of Coccinelle.
Fixes: 2de4973569 ("can: tcan45x: Make wake-up GPIO an optional GPIO")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the device state GPIO is not connected to the host then disable the
INH output from the TCAN device per section 8.3.5 of the data sheet.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It's a good idea to reset a ip-block/spi device before using it, this
patch will reset the device.
And a generic reset function if needed elsewhere.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The tcan4x5x_parse_config() function now performs action on the device
either reading or writing and a reset. If the devive has a switchable
power supppy (i.e. regulator is managed) it needs to be turned on.
So turn on the regulator if available. If the parsing fails, turn off
the regulator.
Fixes: 2de4973569 ("can: tcan45x: Make wake-up GPIO an optional GPIO")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The m_can tries to detect if Non ISO Operation is available while in
standby mode, this function results in the following error:
| tcan4x5x spi2.0 (unnamed net_device) (uninitialized): Failed to init module
| tcan4x5x spi2.0: m_can device registered (irq=84, version=32)
| tcan4x5x spi2.0 can2: TCAN4X5X successfully initialized.
When the tcan device comes out of reset it goes in standby mode. The
m_can driver tries to access the control register but fails due to the
device being in standby mode.
So this patch will put the tcan device in normal mode before the m_can
driver does the initialization.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The common fast path check can be done under rcu_read_lock() and
doesn't need a reference count on the label. Only take a reference
count if entering the slow path.
Fixes reported hackbench regression
- sha1 79e178a57d ("Merge tag 'apparmor-pr-2019-12-03' of
git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor")
hackbench -l (256000/#grp) -g #grp
128 groups 19.679 ±0.90%
- previous sha1 01d1dff646 ("Merge tag 's390-5.5-2' of
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux")
hackbench -l (256000/#grp) -g #grp
128 groups 3.1689 ±3.04%
Reported-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Fixes: bce4e7e9c4 ("apparmor: reduce rcu_read_lock scope for aa_file_perm mediation")
Signed-off-by: John Johansen <john.johansen@canonical.com>
With commit df323337e5 ("apparmor: Use a memory pool instead per-CPU
caches, 2019-05-03"), AppArmor code was converted to use memory pools. In
that conversion, a bug snuck into the code that polices bind mounts that
causes all bind mounts to fail with -ENOMEM, as we erroneously error out
if `aa_get_buffer` returns a pointer instead of erroring out when it
does _not_ return a valid pointer.
Fix the issue by correctly checking for valid pointers returned by
`aa_get_buffer` to fix bind mounts with AppArmor.
Fixes: df323337e5 ("apparmor: Use a memory pool instead per-CPU caches")
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Here's a couple of new modem device ids, including a new quirk for
devices that expect zero-length packets.
Due to the holidays, only the first one has been in linux-next and with
no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXg3MPAAKCRALxc3C7H1l
CMKsAQD5gVqptg42f9oMYnFlAqxKVjnnxxj2FqXDKh8qGiNNUAEAsnGkBp/ZO+wx
3wUxcp6opRIk1ziIvGzY3QIpf/ft6wY=
=u0Ys
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.5-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.5-rc5
Here's a couple of new modem device ids, including a new quirk for
devices that expect zero-length packets.
Due to the holidays, only the first one has been in linux-next and with
no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.5-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add ZLP support for 0x1bc7/0x9010
USB: serial: option: add Telit ME910G1 0x110a composition
*) Fix error path in cpcap-usb driver when no host driver is loaded to
avoid debug serial console from stop working
*) Fix to let USB host idle before switching to UART mode in cpcap-usb
driver in order to avoid flakey enumeration next time
*) Prevent USB line glitches from waking up modem by enabling the USB
lines (GPIO mux) after configuring the cpcap-usb PHY
*) Improve host vs docked mode detection in cpcap-usb PHY driver to keep
VBUS enabled in host mode
*) Fix to prevent cpcap-usb PHY driver from enabling the PHY twice
*) Increase PHY ready timeout in qcom-qmp PHY as it takes more than 1ms
to initialize
*) Round clock rate down to closest 1000 Hz in phy-rockchip-inno-hdmi to
prevent wrong pixel clock to be used and result in no-signal when
configuring a mode on RK3328
-----BEGIN PGP SIGNATURE-----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=a9NM
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.5-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 5.5-rc
*) Fix error path in cpcap-usb driver when no host driver is loaded to
avoid debug serial console from stop working
*) Fix to let USB host idle before switching to UART mode in cpcap-usb
driver in order to avoid flakey enumeration next time
*) Prevent USB line glitches from waking up modem by enabling the USB
lines (GPIO mux) after configuring the cpcap-usb PHY
*) Improve host vs docked mode detection in cpcap-usb PHY driver to keep
VBUS enabled in host mode
*) Fix to prevent cpcap-usb PHY driver from enabling the PHY twice
*) Increase PHY ready timeout in qcom-qmp PHY as it takes more than 1ms
to initialize
*) Round clock rate down to closest 1000 Hz in phy-rockchip-inno-hdmi to
prevent wrong pixel clock to be used and result in no-signal when
configuring a mode on RK3328
* tag 'phy-for-5.5-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy/rockchip: inno-hdmi: round clock rate down to closest 1000 Hz
phy: cpcap-usb: Drop extra write to usb2 register
phy: cpcap-usb: Improve host vs docked mode detection
phy: cpcap-usb: Prevent USB line glitches from waking up modem
phy: mapphone-mdm6600: Fix uninitialized status value regression
phy: cpcap-usb: Fix flakey host idling and enumerating of devices
phy: qcom-qmp: Increase PHY ready timeout
phy: cpcap-usb: Fix error path when no host driver is loaded
-malidp: Make vtable static (Ben)
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Stefan Mavrodiev <stefan@olimex.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHF6rntfJ3enn8gh8cywAJXLcr3kFAl4LaBgACgkQcywAJXLc
r3l58ggA2PKL0955KFeWAV1T8JZEaGSA6i5TNhtQFHbLQO2Ks5tE/YXsAROcA+ry
Eblqk36Yg0NyhsJ8e6FwQYiRdkL3Vh+kpxV+zbexfeKqSuyX12Xqy1Ukbxij0qYt
faDhwh4TYHQnA1QvsPfXSkf0gQt0nWAq2EahHaT9qn0tjjmA1YmAyIh851kBtT4B
UeyDJgLh4l0ALs2dptaVrpB+uKT7GKeQvFoAMddYOBFAQ21/ihJwCQdGBqfYAaO0
PTsfNxjfDnm8s1N/qNV+21Pk1pMm6g9xKTmP/cuD6iwiaWlB5GYxeo6xFLjQ3NVU
EOHv4SJdsm3CFGEggJvqCiBYIJfG9Q==
=+u2K
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2019-12-31' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
-sun4i: Fix double-free in connector/encoder cleanup (Stefan)
-malidp: Make vtable static (Ben)
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20191231152503.GA46740@art_vandelay
Per confirmation with RLC firmware team, the RLC should
be unhalted after all RLC related firmwares uploaded.
However, in fact the RLC is unhalted immediately after
RLCG firmware uploaded. And that may causes unexpected
PSP hang on loading the succeeding RLC save restore
list related firmwares.
So, we correct the firmware loading sequence to load
RLC save restore list related firmwares before RLCG
ucode. That will help to get around this issue.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Pull networking fixes from David Miller:
1) Fix big endian overflow in nf_flow_table, from Arnd Bergmann.
2) Fix port selection on big endian in nft_tproxy, from Phil Sutter.
3) Fix precision tracking for unbound scalars in bpf verifier, from
Daniel Borkmann.
4) Fix integer overflow in socket rcvbuf check in UDP, from Antonio
Messina.
5) Do not perform a neigh confirmation during a pmtu update over a
tunnel, from Hangbin Liu.
6) Fix DMA mapping leak in dpaa_eth driver, from Madalin Bucur.
7) Various PTP fixes for sja1105 dsa driver, from Vladimir Oltean.
8) Add missing to dummy definition of of_mdiobus_child_is_phy(), from
Geert Uytterhoeven
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
net/sched: add delete_empty() to filters and use it in cls_flower
tcp: Fix highest_sack and highest_sack_seq
ptp: fix the race between the release of ptp_clock and cdev
net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
net: dsa: sja1105: Really make the PTP command read-write
net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
cxgb4/cxgb4vf: fix flow control display for auto negotiation
mlxsw: spectrum: Use dedicated policer for VRRP packets
mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs
net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device
net_sched: sch_fq: properly set sk->sk_pacing_status
bnx2x: Fix accounting of vlan resources among the PFs
bnx2x: Use appropriate define for vlan credit
of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy
net: phy: aquantia: add suspend / resume ops for AQR105
dpaa_eth: fix DMA mapping leak
...
Commit 287422a95f ("drm/rockchip: Round up _before_ giving to the clock framework")
changed what rate clk_round_rate() is called with, an additional 999 Hz
added to the requsted mode clock. This has caused a regression on RK3328
and presumably also on RK3228 because the inno-hdmi-phy clock requires an
exact match of the requested rate in the pre pll config table.
When an exact match is not found the parent clock rate (24MHz) is returned
to the clk_round_rate() caller. This cause wrong pixel clock to be used and
result in no-signal when configuring a mode on RK3328.
Fix this by rounding the rate down to closest 1000 Hz in round_rate func,
this allows an exact match to be found in pre pll config table.
Fixes: 287422a95f ("drm/rockchip: Round up _before_ giving to the clock framework")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Revert "net/sched: cls_u32: fix refcount leak in the error path of
u32_change()", and fix the u32 refcount leak in a more generic way that
preserves the semantic of rule dumping.
On tc filters that don't support lockless insertion/removal, there is no
need to guard against concurrent insertion when a removal is in progress.
Therefore, for most of them we can avoid a full walk() when deleting, and
just decrease the refcount, like it was done on older Linux kernels.
This fixes situations where walk() was wrongly detecting a non-empty
filter, like it happened with cls_u32 in the error path of change(), thus
leading to failures in the following tdc selftests:
6aa7: (filter, u32) Add/Replace u32 with source match and invalid indev
6658: (filter, u32) Add/Replace u32 with custom hash table and invalid handle
74c2: (filter, u32) Add/Replace u32 filter with invalid hash table id
On cls_flower, and on (future) lockless filters, this check is necessary:
move all the check_empty() logic in a callback so that each filter
can have its own implementation. For cls_flower, it's sufficient to check
if no IDRs have been allocated.
This reverts commit 275c44aa19.
Changes since v1:
- document the need for delete_empty() when TCF_PROTO_OPS_DOIT_UNLOCKED
is used, thanks to Vlad Buslov
- implement delete_empty() without doing fl_walk(), thanks to Vlad Buslov
- squash revert and new fix in a single patch, to be nice with bisect
tests that run tdc on u32 filter, thanks to Dave Miller
Fixes: 275c44aa19 ("net/sched: cls_u32: fix refcount leak in the error path of u32_change()")
Fixes: 6676d5e416 ("net: sched: set dedicated tcf_walker flag when tp is empty")
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Suggested-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From commit 50895b9de1 ("tcp: highest_sack fix"), the logic about
setting tp->highest_sack to the head of the send queue was removed.
Of course the logic is error prone, but it is logical. Before we
remove the pointer to the highest sack skb and use the seq instead,
we need to set tp->highest_sack to NULL when there is no skb after
the last sack, and then replace NULL with the real skb when new skb
inserted into the rtx queue, because the NULL means the highest sack
seq is tp->snd_nxt. If tp->highest_sack is NULL and new data sent,
the next ACK with sack option will increase tp->reordering unexpectedly.
This patch sets tp->highest_sack to the tail of the rtx queue if
it's NULL and new data is sent. The patch keeps the rule that the
highest_sack can only be maintained by sack processing, except for
this only case.
Fixes: 50895b9de1 ("tcp: highest_sack fix")
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a case when a ptp chardev (like /dev/ptp0) is open but an underlying
device is removed, closing this file leads to a race. This reproduces
easily in a kvm virtual machine:
ts# cat openptp0.c
int main() { ... fp = fopen("/dev/ptp0", "r"); ... sleep(10); }
ts# uname -r
5.5.0-rc3-46cf053e
ts# cat /proc/cmdline
... slub_debug=FZP
ts# modprobe ptp_kvm
ts# ./openptp0 &
[1] 670
opened /dev/ptp0, sleeping 10s...
ts# rmmod ptp_kvm
ts# ls /dev/ptp*
ls: cannot access '/dev/ptp*': No such file or directory
ts# ...woken up
[ 48.010809] general protection fault: 0000 [#1] SMP
[ 48.012502] CPU: 6 PID: 658 Comm: openptp0 Not tainted 5.5.0-rc3-46cf053e #25
[ 48.014624] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
[ 48.016270] RIP: 0010:module_put.part.0+0x7/0x80
[ 48.017939] RSP: 0018:ffffb3850073be00 EFLAGS: 00010202
[ 48.018339] RAX: 000000006b6b6b6b RBX: 6b6b6b6b6b6b6b6b RCX: ffff89a476c00ad0
[ 48.018936] RDX: fffff65a08d3ea08 RSI: 0000000000000247 RDI: 6b6b6b6b6b6b6b6b
[ 48.019470] ... ^^^ a slub poison
[ 48.023854] Call Trace:
[ 48.024050] __fput+0x21f/0x240
[ 48.024288] task_work_run+0x79/0x90
[ 48.024555] do_exit+0x2af/0xab0
[ 48.024799] ? vfs_write+0x16a/0x190
[ 48.025082] do_group_exit+0x35/0x90
[ 48.025387] __x64_sys_exit_group+0xf/0x10
[ 48.025737] do_syscall_64+0x3d/0x130
[ 48.026056] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 48.026479] RIP: 0033:0x7f53b12082f6
[ 48.026792] ...
[ 48.030945] Modules linked in: ptp i6300esb watchdog [last unloaded: ptp_kvm]
[ 48.045001] Fixing recursive fault but reboot is needed!
This happens in:
static void __fput(struct file *file)
{ ...
if (file->f_op->release)
file->f_op->release(inode, file); <<< cdev is kfree'd here
if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL &&
!(mode & FMODE_PATH))) {
cdev_put(inode->i_cdev); <<< cdev fields are accessed here
Namely:
__fput()
posix_clock_release()
kref_put(&clk->kref, delete_clock) <<< the last reference
delete_clock()
delete_ptp_clock()
kfree(ptp) <<< cdev is embedded in ptp
cdev_put
module_put(p->owner) <<< *p is kfree'd, bang!
Here cdev is embedded in posix_clock which is embedded in ptp_clock.
The race happens because ptp_clock's lifetime is controlled by two
refcounts: kref and cdev.kobj in posix_clock. This is wrong.
Make ptp_clock's sysfs device a parent of cdev with cdev_device_add()
created especially for such cases. This way the parent device with its
ptp_clock is not released until all references to the cdev are released.
This adds a requirement that an initialized but not exposed struct
device should be provided to posix_clock_register() by a caller instead
of a simple dev_t.
This approach was adopted from the commit 72139dfa24 ("watchdog: Fix
the race between the release of watchdog_core_data and cdev"). See
details of the implementation in the commit 233ed09d7f ("chardev: add
helper function to register char devs with a struct device").
Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#u
Analyzed-by: Stephen Johnston <sjohnsto@redhat.com>
Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c ("net: dsa: sja1105: Reverse TPID and TPID2")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 86db36a347 ("net: dsa: sja1105: Implement state machine
for TAS with PTP clock source"), this paragraph is no longer true. So
remove it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check originates from the initial implementation which was not based
on PTP time but on a standalone clock source. In the meantime we can now
program the PTPSCHTM register at runtime with the dynamic base time
(actually with a value that is 200 ns smaller, to avoid writing DELTA=0
in the Schedule Entry Points Parameters Table). And we also have logic
for moving the actual base time in the future of the PHC's current time
base, so the check for zero serves no purpose, since even if the user
will specify zero, that's not what will end up in the static config
table where the limitation is.
Fixes: 86db36a347 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When activating tc-taprio offload on the switch ports, the TAS state
machine will try to check whether it is running or not, but will find
both the STARTED and STOPPED bits as false in the
sja1105_tas_check_running function. So the function will return -EINVAL
(an abnormal situation) and the kernel will keep printing this from the
TAS FSM workqueue:
[ 37.691971] sja1105 spi0.1: An operation returned -22
The reason is that the underlying function that gets called,
sja1105_ptp_commit, does not actually do a SPI_READ, but a SPI_WRITE. So
the command buffer remains initialized with zeroes instead of retrieving
the hardware state. Fix that.
Fixes: 41603d78b3 ("net: dsa: sja1105: Make the PTP command read-write")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP egress timestamp N must be captured from register PTPEGR_TS[n],
where n = 2 * PORT + TSREG. There are 10 PTPEGR_TS registers, 2 per
port. We are only using TSREG=0.
As opposed to the management slots, which are 4 in number
(SJA1105_NUM_PORTS, minus the CPU port). Any management frame (which
includes PTP frames) can be sent to any non-CPU port through any
management slot. When the CPU port is not the last port (#4), there will
be a mismatch between the slot and the port number.
Luckily, the only mainline occurrence with this switch
(arch/arm/boot/dts/ls1021a-tsn.dts) does have the CPU port as #4, so the
issue did not manifest itself thus far.
Fixes: 47ed985e97 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When used in Extended SPI mode on LS1021A, the DSPI controller wants to
have the least significant 16-bit word written first to the TX FIFO.
In fact, the LS1021A reference manual says:
33.5.2.4.2 Draining the TX FIFO
When Extended SPI Mode (DSPIx_MCR[XSPI]) is enabled, if the frame size
of SPI Data to be transmitted is more than 16 bits, then it causes two
Data entries to be popped from TX FIFO simultaneously which are
transferred to the shift register. The first of the two popped entries
forms the 16 least significant bits of the SPI frame to be transmitted.
So given the following TX buffer:
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 0x0 | 0x1 | 0x2 | 0x3 | 0x4 | 0x5 | 0x6 | 0x7 | 0x8 | 0x9 | 0xa | 0xb |
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 32-bit word 1 | 32-bit word 2 | 32-bit word 3 |
+-----------------------+-----------------------+-----------------------+
The correct way that a little-endian system should transmit it on the
wire when bits_per_word is 32 is:
0x03020100
0x07060504
0x0b0a0908
But it is actually transmitted as following, as seen with a scope:
0x01000302
0x05040706
0x09080b0a
It appears that this patch has been submitted at least once before:
https://lkml.org/lkml/2018/9/21/286
but in that case Chuanhua Han did not manage to explain the problem
clearly enough and the patch did not get merged, leaving XSPI mode
broken.
Fixes: 8fcd151d26 ("spi: spi-fsl-dspi: XSPI FIFO handling (in TCFQ mode)")
Cc: Esben Haabendal <eha@deif.com>
Cc: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191228135536.14284-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.
[1] https://standards.ieee.org/standard/802_3-2005.html
Fixes: c3168cabe1 ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Signed-off-by: Surendra Mobiya <surendra@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
