Make cht_wc_extcon_get_id() report RID_A for ACA adapters, instead of
reporting ID_FLOAT.
According to the spec. we should read the USB-ID pin ADC value
to determine the resistance of the used pull-down resister and
then return RID_A / RID_B / RID_C based on this. But all "Accessory
Charger Adapter"s (ACAs) which users can actually buy always use
a combination of a charging port with one or more USB-A ports, so
they should always use a resistor indicating RID_A. But the spec
is hard to read / badly-worded so some of them actually indicate
they are a RID_B ACA even though they clearly are a RID_A ACA.
To workaround this simply always return INTEL_USB_RID_A, which
matches all the ACAs which users can actually buy.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq25890 used on the Yogabook YB1-X90 / -X91 models relies on
the extcon-driver's BC-1.2 charger detection, and the bq25890 driver
expect this info to be available through a parent power_supply
class-device which models the detected charger (idem to how the Type-C
TCPM code registers a power_supply classdev for the connected charger).
Add support for registering the power_supply class-device expected
by this setup.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This is a preparation patch for adding support for registering
a power_supply class device.
Setting usbsrc to "CHT_WC_USBSRC_TYPE_SDP << CHT_WC_USBSRC_TYPE_SHIFT"
will make the following switch-case return EXTCON_CHG_USB_SDP
just as before, so there is no functional change.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
So far the extcon-intel-cht-wc code has only been tested on devices with
a Type-C connector with USB-PD, USB3 (superspeed) and DP-altmode support
through a FUSB302 Type-C controller.
Some devices with the intel-cht-wc PMIC however come with an USB-micro-B
connector, or an USB-2 only Type-C connector without USB-PD.
Which device-model we are running on can be identified with the new
cht_wc_model intel_soc_pmic field. On models without a Type-C controller
the extcon code must control the Vbus 5V boost converter and the USB role
switch depending on the detected cable-type.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The CHT_WC_VBUS_GPIO_CTLO GPIO actually driving an external 5V Vboost
converter for Vbus depends on the board on which the Cherry Trail -
Whiskey Cove PMIC is actually used.
Since the information about the exact PMIC setup is necessary in other
places too, struct intel_soc_pmic now has a new cht_wc_model field
indicating the board model.
Only poke the CHT_WC_VBUS_GPIO_CTLO GPIO if this new field is set to
INTEL_CHT_WC_GPD_WIN_POCKET, which indicates the Type-C (with PD and
DP-altmode) setup used on the GPD pocket and GPD win; and on which
this GPIO actually controls an external 5V Vboost converter.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Finding the cable index and checking for changed status is also done
in extcon_set_state(). So calling extcon_set_state_sync() will do these
checks twice. Remove them and use these checks from extcon_set_state().
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Do not use "/**" to begin a non-kernel-doc comment.
Fixes this build warning:
drivers/extcon/extcon-usb-gpio.c:23:
warning: expecting prototype for drivers/extcon/extcon-usb-gpio.c().
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
TUSB320L is a newer chip with additional features, and it has additional steps
in its mode changing sequence:
- Disable CC state machine,
- Write to mode register,
- Wait for 5 ms,
- Re-enable CC state machine.
It also has an additional register that a revision number can be read from.
Add support for the mode changing sequence, and read the revision number during
probe and print it as info.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reset the chip and set its mode to default (maintain mode set by PORT pin)
during probe to make sure it comes up in the default state.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
use low level P-Unit semaphore lock for axp288 register
accesses directly and for more than one access a time,
to reduce the number of times this semaphore is locked
and released which is an expensive operation.
i2c-bus to the XPower is shared between the kernel and the
SoCs P-Unit. The P-Unit has a semaphore wich the kernel must
lock for axp288 register accesses. When the P-Unit semaphore
is locked CPU and GPU power states cannot change or the system
will freeze.
The P-Unit semaphore lock is already managed inside the regmap
access logic, but for each access the semaphore is locked and
released. So use directly iosf_mbi_(un)block_punit_i2c_access(),
we are safe in doing so because nested calls to the same
semaphore are turned to nops.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This driver includes the legacy <linux/gpio.h> header but
does not use it. Drop this include.
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The USB GPIO extcon driver does not use any of the legacy
includes <linux/gpio.h> or <linux/of_gpio.h> but
exploits the fact that this brings in <linux/mod_device_table.h>.
Fix this up by using the right includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanna driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems mushed
together" tree...
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM8jQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymECgCg0yL+8WxDKO5Gg5llM5PshvLB1rQAn0y5pDgg
nw78LV3HQ0U7qaZBtI91
=x+AR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
SM5504 is another MUIC from Silicon Mitus that is fairly similar
to SM5502. They seem to use the same register set, but:
- SM5504 has some additional bits in SM5502_REG_CONTROL
- SM5504 has a quite different set of interrupts
- SM5504 reports USB OTG as dev_type1 = BIT(0) instead of BIT(7)
Overall it's minor and we can support this by defining a separate
struct sm5502_type for SM5504.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Prepare for supporting SM5504 in the extcon-sm5502 driver by replacing
enum sm5504_types with a struct sm5504_type that stores the chip-specific
definitions. This struct can then be defined separately for SM5504
without having to add if (type == TYPE_SM5504) everywhere in the code.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
sm5022_muic_i2c_probe() does not use the i2c_device_id,
so implement i2c_driver->probe_new() instead of probe().
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Use devm_regmap_add_irq_chip() to avoid having to remove the
irqchip explicitly in sm5502_muic_i2c_remove().
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The platform device driver name is "max8997-muic", so advertise it
properly in the modalias string. This fixes automated module loading when
this driver is compiled as a module.
Fixes: b76668ba8a ("Extcon: add MAX8997 extcon driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
When sm5502_init_dev_type() iterates over sm5502_reg_data to
initialize the registers it is limited by ARRAY_SIZE(sm5502_reg_data).
There is no need to add another empty element to sm5502_reg_data.
Having the additional empty element in sm5502_reg_data will just
result in writing 0xff to register 0x00, which does not really
make sense.
Fixes: 914b881f94 ("extcon: sm5502: Add support new SM5502 extcon device driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
extcon driver for Basin Cove PMIC shadows the switch status used for dwc3
DRD to detect a change in the switch position. This change initializes the
status at probe time.
Cc: stable@vger.kernel.org
Fixes: 492929c547 ("extcon: mrfld: Introduce extcon driver for Basin Cove PMIC")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
If reading MAX8997_MUIC_REG_STATUS1 fails at probe the driver exits
without freeing the requested IRQs.
Free the IRQs prior returning if reading the status fails.
Fixes: 3e34c81989 ("extcon: max8997: Avoid forcing UART path on drive probe")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/27ee4a48ee775c3f8c9d90459c18b6f2b15edc76.1623146580.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The extcon IRQ schedules a work item. IRQ is requested using devm while
WQ is cancelld at remove(). This mixing of devm and manual unwinding has
potential case where the WQ has been emptied (.remove() was ran) but
devm unwinding of IRQ was not yet done. It may be possible the IRQ is
triggered at this point scheduling new work item to the already flushed
queue.
According to the input documentation the input device allocated by
devm_input_allocate_device() does not need to be explicitly unregistered.
Use the new devm_work_autocancel() and remove the remove() to simplify the
code.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/cbe8205eed8276f6e6db5003cfe51b8b0d4ac966.1623146580.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The extcon IRQ schedules a work item. IRQ is requested using devm while
WQ is cancelld at remove(). This mixing of devm and manual unwinding has
potential case where the WQ has been emptied (.remove() was ran) but
devm unwinding of IRQ was not yet done. It is possible the IRQ is triggered
at this point scheduling new work item to the already flushed queue.
Use new devm_work_autocancel() to remove the remove() and to kill the bug.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/ee8545f59ae3a93f0a70f640ecbd7e31cfadbcb9.1623146580.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
- New Drivers
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
- New Device Support
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
- Removed Device Support
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
- New Functionality
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
- New/converted Device Tree bindings; rohm,bd71815-pmic, rohm,bd9576-pmic,
netronix,ntxec, actions,atc260x,
ricoh,rn5t618, qcom-pm8xxx
- Fix-ups
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618, max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci,
atc260x-i2c, intel_quark_i2c_gpio
- Bug Fixes
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers
-----BEGIN PGP SIGNATURE-----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=IJSL
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
New Drivers:
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
New Device Support:
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
Removed Device Support:
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
New Functionality:
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
New/converted Device Tree bindings:
- rohm bd71815-pmic, rohm bd9576-pmic, netronix ntxec, actions
atc260x, ricoh rn5t618, qcom pm8xxx
- Fix-ups:
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618,
max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci, atc260x-i2c, intel_quark_i2c_gpio
Bug Fixes:
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers"
* tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
mfd: intel-m10-bmc: Add support for MAX10 BMC Secure Updates
Revert "mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell"
mfd: twl: Remove unused inline function twl4030charger_usb_en()
dt-bindings: mfd: Convert pm8xxx bindings to yaml
dt-bindings: mfd: Add compatible for pmk8350 rtc
i2c: designware: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert I²C to use software nodes
mfd: lpc_sch: Partially revert "Add support for Intel Quark X1000"
mfd: arizona: Fix rumtime PM imbalance on error
mfd: max8997: Replace 8998 with 8997
mfd: core: Use acpi_find_child_device() for child devices lookup
mfd: intel_quark_i2c_gpio: Don't play dirty trick with const
mfd: intel_quark_i2c_gpio: Enable MSI interrupt
mfd: intel_quark_i2c_gpio: Reuse BAR definitions for MFD cell indexing
mfd: ntxec: Support for EC in Tolino Shine 2 HD
mfd: stm32-timers: Avoid clearing auto reload register
mfd: intel_quark_i2c_gpio: Replace I²C speeds with descriptive definitions
mfd: intel_quark_i2c_gpio: Remove unused struct device member
mfd: intel_quark_i2c_gpio: Unregister resources in reversed order
mfd: Kconfig: ABX500_CORE should depend on ARCH_U8500
...
Here is the "big" set of driver core changes for 5.13-rc1.
Nothing major, just lots of little core changes and cleanups, notable
things are:
- finally set fw_devlink=on by default. All reported issues
with this have been shaken out over the past 9 months or so,
but we will be paying attention to any fallout here in case we
need to revert this as the default boot value (symptoms of
problems are a simple lack of booting)
- fixes found to be needed by fw_devlink=on value in some
subsystems (like clock).
- delayed work initialization cleanup
- driver core cleanups and minor updates
- software node cleanups and tweaks
- devtmpfs cleanups
- minor debugfs cleanups
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYIazPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylzUwCguQ+VUs1d0voq/oKiqR+lbXnQf3kAn0jf/eom
ucRSdeIc21eEE83Ei9aZ
=pchl
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core changes for 5.13-rc1.
Nothing major, just lots of little core changes and cleanups, notable
things are:
- finally set 'fw_devlink=on' by default.
All reported issues with this have been shaken out over the past 9
months or so, but we will be paying attention to any fallout here
in case we need to revert this as the default boot value (symptoms
of problems are a simple lack of booting)
- fixes found to be needed by fw_devlink=on value in some subsystems
(like clock).
- delayed work initialization cleanup
- driver core cleanups and minor updates
- software node cleanups and tweaks
- devtmpfs cleanups
- minor debugfs cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (53 commits)
devm-helpers: Fix devm_delayed_work_autocancel() kerneldoc
PM / wakeup: use dev_set_name() directly
software node: Allow node addition to already existing device
kunit: software node: adhear to KUNIT formatting standard
node: fix device cleanups in error handling code
kobject_uevent: remove warning in init_uevent_argv()
debugfs: Make debugfs_allow RO after init
Revert "driver core: platform: Make platform_get_irq_optional() optional"
media: ipu3-cio2: Switch to use SOFTWARE_NODE_REFERENCE()
software node: Introduce SOFTWARE_NODE_REFERENCE() helper macro
software node: Imply kobj_to_swnode() to be no-op
software node: Deduplicate code in fwnode_create_software_node()
software node: Introduce software_node_alloc()/software_node_free()
software node: Free resources explicitly when swnode_register() fails
debugfs: drop pointless nul-termination in debugfs_read_file_bool()
driver core: add helper for deferred probe reason setting
driver core: Improve fw_devlink & deferred_probe_timeout interaction
of: property: fw_devlink: Add support for remote-endpoint
driver core: platform: Make platform_get_irq_optional() optional
driver core: Replace printf() specifier and drop unneeded casting
...
VBUS can be detected via a dedicated PMIC pin. Add support
for reporting the VBUS status.
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Signed-off-by: Kavya Nunna <knunna@codeaurora.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
In it's curent state this driver ignores OTG adapters with ID pin
connected to ground. This commit adds a check to set extcon into
host mode when such OTG adapter is connected.
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This allows the MAX8997 charger to set the current limit depending on
the detected extcon charger type.
Signed-off-by: Timon Baetz <timon.baetz@protonmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Few drivers implement remove call-back only for ensuring a delayed
work gets cancelled prior driver removal. Clean-up these by switching
to use devm_delayed_work_autocancel() instead.
Additionally, this helps avoiding mixing devm and manual resource
management and cleans up a (theoretical?) bug from extconn-palmas.c
and extcon-qcom-spmi-misc.c where (devm managed)IRQ might schedule
new work item after wq was cleaned at remove().
This change is compile-tested only. All testing is appreciated.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/b1030eddbf0069f2d39e951be1d8e40d6413aeeb.1616506559.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The jack handling for arizona codecs is being refactored so that it is
done directly by the codec drivers, instead of having an extcon-driver
bind to a separate "arizona-extcon" child-device for this.
drivers/mfd/arizona-core.c has already been updated to no longer
instantiate an "arizona-extcon" child-device for the arizona codecs.
This means that the "arizona-extcon" driver is no longer useful
(there are no longer any devices for it to bind to).
This commit drops the extcon Kconfig / Makefile bits and moves
drivers/extcon/extcon-arizona.c to sound/soc/codecs/arizona-jack.c .
This is a preparation patch for converting the arizona extcon-driver into
a helper library for letting the arizona codec-drivers directly report jack
state through the standard sound/soc/soc-jack.c functions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Before this commit the extcon-arizona code was mixing pm_runtime_get()
and pm_runtime_get_sync() in different places.
In all places where pm_runtime_get[_sync]() is called, the code
makes use of the device immediately after the call.
This means that we should always use pm_runtime_get_sync().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The initial value of the GPIO should match the info->micd_modes[0].gpio
value. arizona_extcon_probe() already stores the necessary flag in a
mode variable, but instead of passing mode as flags to the gpiod_get()
it was using a hardcoded GPIOD_OUT_LOW.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We must free/disable all interrupts and cancel all pending works
before doing further cleanup.
Before this commit arizona_extcon_remove() was doing several
register writes to shut things down before disabling the IRQs
and it was cancelling only 1 of the 3 different works used.
Move all the register-writes shutting things down to after
the disabling of the IRQs and add the 2 missing
cancel_delayed_work_sync() calls.
This fixes various possible races on driver unbind. One of which
would always trigger on devices using the mic-clamp feature for
jack detection. The ARIZONA_MICD_CLAMP_MODE_MASK update was
done before disabling the IRQs, causing:
1. arizona_jackdet() to run
2. detect a jack being inserted (clamp disabled means jack inserted)
3. call arizona_start_mic() which:
3.1 Enables the MICVDD regulator
3.2 takes a pm_runtime_reference
And this was all happening after the ARIZONA_MICD_ENA bit clearing,
which would undo 3.1 and 3.2 because the ARIZONA_MICD_CLAMP_MODE_MASK
update was being done after the ARIZONA_MICD_ENA bit clearing.
So this means that arizona_extcon_remove() would exit with
1. MICVDD enabled and 2. The pm_runtime_reference being unbalanced.
MICVDD still being enabled caused the following oops when the
regulator is released by the devm framework:
[ 2850.745757] ------------[ cut here ]------------
[ 2850.745827] WARNING: CPU: 2 PID: 2098 at drivers/regulator/core.c:2123 _regulator_put.part.0+0x19f/0x1b0
[ 2850.745835] Modules linked in: extcon_arizona ...
...
[ 2850.746909] Call Trace:
[ 2850.746932] regulator_put+0x2d/0x40
[ 2850.746946] release_nodes+0x22a/0x260
[ 2850.746984] __device_release_driver+0x190/0x240
[ 2850.747002] driver_detach+0xd4/0x120
...
[ 2850.747337] ---[ end trace f455dfd7abd9781f ]---
Note this oops is just one of various theoretically possible races caused
by the wrong ordering inside arizona_extcon_remove(), this fixes the
ordering fixing all possible races, including the reported oops.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When the jack is partially inserted and then removed again it may be
removed while the hpdet code is running. In this case the following
may happen:
1. The "JACKDET rise" or ""JACKDET fall" IRQ triggers
2. arizona_jackdet runs and takes info->lock
3. The "HPDET" IRQ triggers
4. arizona_hpdet_irq runs, blocks on info->lock
5. arizona_jackdet calls arizona_stop_mic() and clears info->hpdet_done
6. arizona_jackdet releases info->lock
7. arizona_hpdet_irq now can continue running and:
7.1 Calls arizona_start_mic() (if a mic was detected)
7.2 sets info->hpdet_done
Step 7 is undesirable / a bug:
7.1 causes the device to stay in a high power-state (with MICVDD enabled)
7.2 causes hpdet to not run on the next jack insertion, which in turn
causes the EXTCON_JACK_HEADPHONE state to never get set
This fixes both issues by skipping these 2 steps when arizona_hpdet_irq
runs after the jack has been unplugged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When devm_kcalloc() fails, we should execute device_unregister()
to unregister edev->dev from system.
Fixes: 046050f6e6 ("extcon: Update the prototype of extcon_register_notifier() with enum extcon")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The platform device driver name is "max77693-muic", so advertise it
properly in the modalias string. This fixes automated module loading when
this driver is compiled as a module.
Fixes: db1b903742 ("extcon: MAX77693: Add extcon-max77693 driver to support Maxim MAX77693 MUIC device")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The Texas Instruments TSU6111 is compatible to the
FSA880/FSA9480.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds an extcon driver for the TI TUSB320 USB Type-C device.
This can be used to detect whether the port is configured as a
downstream or upstream facing port.
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
module_platform_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The commit 85256f611f ("extcon: ptn5150: Check current USB mode when
probing") reused code for checking CC status register in the probe path
to determine what is initially connected. However if nothing is
connected, the CC status register will have 0x0 value and print an error
message:
ptn5150 1-003d: Unknown Port status : 0
This is not an error. Also any other unknown port status values are not
really errors but unhandled cases.
Fixes: 85256f611f ("extcon: ptn5150: Check current USB mode when probing")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The register addresses are not continuous, so use simple defines for
them. This also makes it easier to find the address for register.
No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
devm_extcon_dev_allocate() can fail of multiple reasons. The call
returns proper error code on failure so pass it instead of fixed ENOMEM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
devm_extcon_dev_allocate() can fail of multiple reasons. The call
returns proper error code on failure so pass it instead of fixed ENOMEM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
devm_extcon_dev_allocate() can fail of multiple reasons. The call
returns proper error code on failure so pass it instead of fixed ENOMEM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
devm_extcon_dev_allocate() can fail of multiple reasons. The call
returns proper error code on failure so pass it instead of fixed ENOMEM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Set the capability value of property for VBUS and POLARITY.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
[cw00.choi: Replace the space with tab for the indentation]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
