mdc pin should always be output. Initialize it as output,
so each board code does not need to do this.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
In most cases (e.g. PCI drivers) MDIO and MAC controllers are
represented by the same device. But for SOC ethernets we have
separate devices. So, in SOC case, checking whether MDIO
controller may wakeup is not only makes little sense, but also
prevents us from doing per-netdevice wakeup management.
This patch reworks suspend/resume code so that now it checks
for net device's wakeup flags, not MDIO controller's ones.
Each netdevice should manage its wakeup flags, and phylib will
decide whether suspend an attached PHY or not.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All supported SMSC PHYs implement the standard "power down" bit 11 of
BMCR, so this patch adds support using the generic genphy_{suspend,resume}
functions.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suspend/resume routines check for phydrv != NULL, but that is
wrong because "phydrv" comes from container_of(drv). If drv is NULL,
then container_of(drv) will return non-NULL result, and the checks
won't work.
The Freescale TBI PHYs are driver-less, so "drv" is NULL, and that
leads to the following oops:
Unable to handle kernel paging request for data at address 0xffffffe4
Faulting instruction address: 0xc0215554
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c0215554] mdio_bus_suspend+0x34/0x70
LR [c01cc508] suspend_device+0x258/0x2bc
Call Trace:
[cfad3da0] [cfad3db8] 0xcfad3db8 (unreliable)
[cfad3db0] [c01cc508] suspend_device+0x258/0x2bc
[cfad3dd0] [c01cc62c] dpm_suspend+0xc0/0x140
[cfad3e20] [c01cc6f4] device_suspend+0x48/0x5c
[cfad3e40] [c0068dd8] suspend_devices_and_enter+0x8c/0x148
[cfad3e60] [c00690f8] enter_state+0x100/0x118
[cfad3e80] [c00691c0] state_store+0xb0/0xe4
[cfad3ea0] [c018c938] kobj_attr_store+0x24/0x3c
[cfad3eb0] [c00ea9a8] flush_write_buffer+0x58/0x7c
[cfad3ed0] [c00eadf0] sysfs_write_file+0x58/0xa0
[cfad3ef0] [c009e810] vfs_write+0xb4/0x16c
[cfad3f10] [c009ed40] sys_write+0x4c/0x90
[cfad3f40] [c0014954] ret_from_syscall+0x0/0x38
[...]
This patch fixes the issue, plus removes unneeded parentheses
and fixes indentation level in mdio_bus_suspend().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
both pdata->mdc and pdata->mdio are unsigned. Notice a negative
return value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freescale on-chip TBI PHYs reports PHY ID as 0x0, but as of
commit 3ee82383f0
Author: Giulio Benetti <giulio.benetti@micronovasrl.com>
Date: Thu Nov 13 21:53:13 2008 +0000
phy: fix phy address bug
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
phy_device.c treats PHY ID == 0x0 as bogus IDs, and that results in
gianfar driver failure to see the TBI PHYs. This code snippet triggers:
if (!priv->tbiphy) {
printk(KERN_WARNING "SGMII mode requires that the device "
"tree specify a tbi-handle\n");
return;
}
Although tbi-handle is specified in the device tree.
Btw, technically PHY ID == 0x0 is a valid ID (if we ever see a PHY
manufactured by Xerox :-).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHYLIB mdio code has more problems in error paths:
- mdiobus_release can be called before bus->state is set to
MDIOBUS_REGISTERED
- mdiobus_scan allocates resources which need to be freed
- the comment is wrong, the resistors used are actually pull-ups.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
kernel BUG at drivers/net/phy/mdio_bus.c:165!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
How?
mdiobus_alloc() sets bus->state = MDIOBUS_ALLOCATED.
mdiobus_register() sets bus->state = MDIOBUS_REGISTERED but then can
fail (mdiobus_scan()) returning an error to the caller.
The caller aborts correctly with mdiobus_free() which does:
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_setup_forced hasn't actually reset the PHY for a long time,
but a comment to that effect remained in the code, so code continued
to act as if it *had* reset the PHY, and called the necessary fixup
functions to respond to a PHY reset. With no reset, those functions
are no longer needed, so we remove them.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds LSI ET1011C PHY driver.
This driver is used by TI DM646x EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the STMicroelectronics ste10xp PHY device driver.
It supports both the ste100p and the ste101p devices.
Suspend/resume alredy added.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the power management support into the physical
abstraction layer.
Suspend and resume functions respectively turns on/off the bit 11
into the PHY Basic mode control register.
Generic PHY device starts supporting PM.
In order to support the wake-on LAN and avoid to put in power down
the PHY device, the MDIO is aware of what the Ethernet device wants to do.
Voluntary, no CONFIG_PM defines were added into the sources.
Also generic suspend/resume functions are exported to allow
other drivers use them (such as genphy_config_aneg etc.).
Within the phy_driver_register function, we need to remove the
memset. It overrides the device driver owner and it is not good.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PHY device driver for the National Semiconductor
DP83865 Gig PHYTER.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY is mostly compatible with the existing VSC8244 PHY. The init sequence
is different and the interrupt mask lacks some bits present in the VSC8244.
Rather than making a copy of the existing VSC234x config_intr function and
change one constant, I modify it to select the interrupt mask based on
which driver is calling it. This lets it be used by both drivers.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 57780 PHY ID to the broadcom module.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the case when the phy_ids is mostly Fs and in some case 0x0
due to broken hardware.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous patch, 51e2a3846e, made
genphy_config_aneg() not restart aneg by calling genphy_restart_aneg() if
the advertisement hadn't changed.
But, genphy_restart_aneg() doesn't just restart aneg, it may also *enable*
aneg or un-isolate the PHY from the MII (those functions are controlled by
the same register). The code to avoid calling genphy_restart_aneg() didn't
consider this.
So, modify genphy_config_aneg() to also check if the PHY needs to have aneg
enabled or be un-isolated before deciding not to restart aneg.
This caused a problem with certain Davicom PHYs, as that driver isolates
the PHY (why?) before calling genphy_config_aneg() and expects the PHY to
be un-isolated by that function.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make mdio-gpio work with non OpenFirmware gpio implementation.
Aditional changes to mdio-gpio:
- use gpio_request() and gpio_free()
- place irq[] array in struct mdio_gpio_info
- add module description, author and license
- add note about compiling this driver as module
- rename mdc and mdio function (were ugly names)
- change MII to MDIO in bus name
- add __init __exit to module (un)loading functions
- probe fails if no phys added to the bus
- kzalloc bitbang with sizeof(*bitbang)
Changes since v3:
- keep bus naming "%x" to be compatible with existing drivers.
Changes since v2:
- more #ifdefs reduction
- platform driver will be registered on OF platforms also
- unified platform and OF bus_id to phy%i
Changes since v1:
- removed NO_IRQ
- reduced #idefs
Laurent, please test this driver under OF.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add support for the Marvell 88E1118 PHY which supports gigabit ethernet among other things.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 46abc02175 ("phylib: give mdio
buses a device tree presence") added a call to device_unregister() in
a situation where the caller did not intend for the device to be
freed yet, but apart from just unregistering the device from the
system, device_unregister() does an additional put_device() that is
intended to free it.
The right function to use in this situation is device_del(), which
unregisters the device from the system like device_unregister() does,
but without dropping the reference count an additional time.
Bug report from Bryan Wu <cooloney@kernel.org>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.
There is an existing smc911x driver in the tree; this is intended to
replace it. Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.
This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.
This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: Dustin Mcintire <dustin@sensoria.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the BCM50610 to the list of phys supported by the
broadcom driver.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the expansion register access routines a little more
formal. They will be used by the following bcm50610 support patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds flow control support to Broadcom phys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core now has this helper function, so might as well use it
instead of forcing the phy code to roll their own version.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following build error caused by
commit ed94493fb3
(mv643xx_eth: convert to phylib):
<-- snip -->
...
Building modules, stage 2.
MODPOST 1280 modules
ERROR: "genphy_restart_aneg" [drivers/net/mv643xx_eth.ko] undefined!
...
make[2]: *** [__modpost] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warning, missing description:
Warning(lin2627-g3-kdocfixes//drivers/net/phy/mdio_bus.c:63): No description found for parameter 'd'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. arch/powerpc/platforms/pasemi/gpio_mdio.c also needs to be
converted over to mdiobus_{alloc,free}().
2. drivers/net/phy/fixed.c used to embed a struct mii_bus into its
struct fixed_mdio_bus and then use container_of() to go from the
former to the latter. Since mii bus structures are no longer
embedded, we need to do something like use the mii bus private
pointer to go from mii_bus to fixed_mdio_bus instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mdiobus_{read,write} routines to allow direct reading/writing
of registers on an mii bus without having to go through the PHY
abstraction, and make phy_{read,write} use these primitives.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the mdio_bus class, and give each 'struct mii_bus' its own
'struct device', so that mii_bus objects are represented in the device
tree and can be found by querying the device tree.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces mdiobus_alloc() and mdiobus_free(), and
makes all mdio bus drivers use these functions to allocate their
struct mii_bus'es dynamically.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
In preparation of giving mii_bus objects a device tree presence of
their own, rename struct mii_bus's ->dev argument to ->parent, since
having a 'struct device *dev' that points to our parent device
conflicts with introducing a 'struct device dev' representing our own
device.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
This way the phy layer will respond to a change in phy state immediately,
instead of up to one second later when the state machine timer runs.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY's aneg is configured and restarted whenever the link is brought up,
e.g. when DHCP is started after the kernel has booted. This can take the
link down for several seconds while auto-negotiation is redone.
If the advertised features haven't changed, then it shouldn't be necessary
to bring down the link and start auto-negotiation over again.
genphy_config_advert() is enhanced to return 0 when the advertised features
haven't been changed and >0 when they have been.
genphy_config_aneg() then uses this information to not call
genphy_restart_aneg() if there has been no change.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the SIOCGMIIPHY case fall through properly (it is supposed
to not only return the ID of the default PHY but also to read from
that PHY), and make phy_mii_ioctl() return the same error code as
generic_mii_ioctl() in case of an unsupported operation.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the bus scanning code in mdiobus_register() off
into a separate function, and makes this function available for
calling from external code. This allows incrementally scanning an
mii bus, e.g. as information about which addresses are 'safe' to
scan becomes available.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
MII_M1111_HWCFG_FIBER_COPPER_RES is a bit of MII_M1111_PHY_EXT_SR, not
MII_M1111_PHY_EXT_CR.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The 27.15 bit (MII_M1111_HWCFG_FIBER_COPPER_AUTO) is disable bit. When
set to 1, copper/fiber auto selection is disabled. The current code
to enable but actually disable auto selection.
Signed-off-by: Wang Jian <lark@linux.net.cn>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
{alloc,free}_mdio_bitbang() are not exported while they are used in
mdio-ofgpio driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
