Commit Graph

134 Commits

Author SHA1 Message Date
Johannes Berg
08960dea6c iwlagn: remove pointless return variables
A number of places just use a variable to return
it right away, which is useless, so let's remove
the variables there.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-07 15:51:35 -04:00
Daniel Halperin
2520546aec iwlwifi: add RATE_MCS_RATE_MSK
Throughout the code we use rate_n_flags & 0xff to extract the lower byte
of the rate_n_flags u32 that contains the information about the rate.
Add a #define and remove the use of the magic number.

Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-03-25 06:58:06 -07:00
Daniel Halperin
374920cb05 iwlwifi: limit number of attempts for highest HT rate
When filling out its rate scale table, iwlwifi repeats the first HT rate
IWL_HT_NUMBER_TRY times. The hardware scheduler will stop using
aggregation for any frame that fails LINK_QUAL_AGG_DISABLE_START_DEF
times. Currently, both these constants equal 3.

If iwlwifi probes a faster rate than the link supports, all frames in a
(potentially tens of frames large) batch will fail IWL_HT_NUMBER_TRY
times. Because this happens to be as large as
LINK_QUAL_AGG_DISABLE_START_DEF, all frames will then be sent
individually. This leads to a short, but performance-degrading window
where the legacy stop-and-wait MAC takes over.

Bounding the initial rate by (LINK_QUAL_AGG_DISABLE_START_DEF-1)
attempts makes the third try use a lower rate and hence more be likely
to succeed. This somewhat mitigates the above described behavior.

Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-03-25 06:57:50 -07:00
Johannes Berg
7b09068721 iwlwifi: use maximum aggregation size
Use the values from the peer to set up the ucode
for the right maximum number of subframes in an
aggregate. Since the ucode only tracks this per
station, use the minimum across all aggregation
sessions with this peer.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:19:32 -08:00
Wey-Yi Guy
7fc11e9bbe iwlagn: adjust rate table
Minor adjustment for rate scale table

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:17:43 -08:00
Sedat Dilek
7d5f01ad53 iwlwifi: Fix error: struct iwl_lq_sta has no member named dbg_fixed_rate
While compiling linux-next (next-20101216) I fell over this breakage:
...
drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In function ‘iwl_rs_rate_init’:
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2876:8: error: ‘struct iwl_lq_sta’ has no member named ‘dbg_fixed_rate’

dbg_fixed_rate is only used when CONFIG_MAC80211_DEBUGFS is set:

[ drivers/net/wireless/iwlwifi/iwl-agn-rs.h ]
...
 #ifdef CONFIG_MAC80211_DEBUGFS
       struct dentry *rs_sta_dbgfs_scale_table_file;
       struct dentry *rs_sta_dbgfs_stats_table_file;
       struct dentry *rs_sta_dbgfs_rate_scale_data_file;
       struct dentry *rs_sta_dbgfs_tx_agg_tid_en_file;
       u32 dbg_fixed_rate;
 #endif

The issue was introduced by commit a1da077bc3:
"iwlwifi: clear dbg_fixed_rate during init"

Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16 09:47:02 -05:00
Sujith Manoharan
bd2ce6e43f mac80211: Add timeout to BA session start API
Allow drivers or rate control algorithms to specify BlockAck session
timeout when initiating an ADDBA transaction. This is useful in cases
where maintaining persistent BA sessions does not incur any overhead.

The current timeout value of 5000 TUs is retained for all non ath9k/ath9k_htc
drivers.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-15 17:03:59 -05:00
Shanyu Zhao
a1da077bc3 iwlwifi: clear dbg_fixed_rate during init
This prevent bad fixed_rate keeps crashing uCode in an endless loop.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-12-13 15:51:01 -08:00
Wey-Yi Guy
66e863a527 iwlagn: support dynamic aggregation for BT coex
Use dynamic aggregation threshold if bt traffic load is high
to reduce the impact on aggregated frame.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:44:00 -08:00
Linus Torvalds
5f05647dd8 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
  bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
  vlan: Calling vlan_hwaccel_do_receive() is always valid.
  tproxy: use the interface primary IP address as a default value for --on-ip
  tproxy: added IPv6 support to the socket match
  cxgb3: function namespace cleanup
  tproxy: added IPv6 support to the TPROXY target
  tproxy: added IPv6 socket lookup function to nf_tproxy_core
  be2net: Changes to use only priority codes allowed by f/w
  tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
  tproxy: added tproxy sockopt interface in the IPV6 layer
  tproxy: added udp6_lib_lookup function
  tproxy: added const specifiers to udp lookup functions
  tproxy: split off ipv6 defragmentation to a separate module
  l2tp: small cleanup
  nf_nat: restrict ICMP translation for embedded header
  can: mcp251x: fix generation of error frames
  can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
  can-raw: add msg_flags to distinguish local traffic
  9p: client code cleanup
  rds: make local functions/variables static
  ...

Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
2010-10-23 11:47:02 -07:00
Arnd Bergmann
6038f373a3 llseek: automatically add .llseek fop
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.

The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.

New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time.  Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.

The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.

Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.

Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.

===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
//   but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}

@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}

@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
   *off = E
|
   *off += E
|
   func(..., off, ...)
|
   E = *off
)
...+>
}

@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}

@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
  *off = E
|
  *off += E
|
  func(..., off, ...)
|
  E = *off
)
...+>
}

@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}

@ fops0 @
identifier fops;
@@
struct file_operations fops = {
 ...
};

@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
 .llseek = llseek_f,
...
};

@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
 .read = read_f,
...
};

@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
 .write = write_f,
...
};

@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
 .open = open_f,
...
};

// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
...  .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};

@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
...  .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};

// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
...  .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};

// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};

// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};

@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+	.llseek = default_llseek, /* write accesses f_pos */
};

// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////

@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
 .write = write_f,
 .read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};

@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};

@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};

@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
2010-10-15 15:53:27 +02:00
Johannes Berg
635b85b427 iwlwifi: remove agn rates info there
Code and data related to agn bitrates can be
part of the agn module rather than being in
the core module.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-10-07 15:51:20 -07:00
Johannes Berg
a30e3112a8 iwlwifi: move agn specific station code there
By duplicating a little bit of code between 3945
and agn, we can move a lot of code into an agn
specific station management file and thus reduce
the amount of code in core that is dead to 3945.

before:
   text	   data	    bss	    dec	    hex	filename
 212886	   3872	     96	 216854	  34f16	iwlcore.ko
 620542	  10448	    304	 631294	  9a1fe	iwlagn.ko
 314013	   3264	    196	 317473	  4d821	iwl3945.ko

after:
   text	   data	    bss	    dec	    hex	filename
 202857	   3872	     92	 206821	  327e5	iwlcore.ko
 629102	  10448	    308	 639858	  9c372	iwlagn.ko
 314240	   3264	    196	 317700	  4d904	iwl3945.ko

delta:
 -10029   iwlcore.ko
   8560   iwlagn.ko
    227   iwl3945.ko

so it's a net win even if you have both loaded,
likely because a lot of EXPORT_SYMBOLs go away.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-10-07 15:50:33 -07:00
Wey-Yi Guy
7cb1b0887f iwlagn: reduce redundant parameter definitions
move paramater definitions to a device paramater structure only
leaving the device name, which antennas are used and what firmware
file to use in the iwl_cfg structure.  this will not completely
remove the redundancies but greatly reduce them for devices that
only vary by name or antennas.  the parameters that are more
likely to change within a given device family are left in iwl_cfg.
also separate bt param structure added to help reduce more.

Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-10-06 08:10:00 -07:00
Johannes Berg
7e6a588601 iwlwifi: move HT configuration data into context
A lot of HT configuration semantically belongs into
the context, even if right now it will never be
different between contexts. Move it so we're better
prepared for future changes in mac80211.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-08-27 09:27:19 -07:00
Wey-Yi Guy
da5dbb9715 iwlagn: set traffic load based on multiple factors
Current BT traffic load should based on the following conditions:

1. BT On/Off status
2. Channel announcement enable/disable
3. Curren traffic load report from uCode

Need to modify rate scale to down-grade from MIMO to SISO if detected
high BT traffic load. Also need to make sure not using chain "B" with high
BT traffic or if it is in "full concurrency" mode.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-25 14:34:53 -04:00
Wey-Yi Guy
bee008b783 iwlwifi: add bt full concurrency support
Adding the bluetooth full concurrency support for WiFi/BT combo devices.

Driver should configure uCode to operate in "full concurrency" mode (via
LUT) if both conditions are met:
 - Antenna Coupling is more than 35dB
 - WiFi Channel Inhibition Request is hornored by BT Core

Currently, there is no antenna coupling information provided by uCode;
use module parameter to specified the antenna coupling in dB.

When in "full concurrency" mode, driver need to download different LUT
to uCode while sending bt configuration command; also, driver need to
configure the device operate in 1x1 while in full concurrency mode.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-25 14:34:19 -04:00
Johannes Berg
290f599cc6 iwlagn: let bluetooth traffic load impact rate scale
Depending on the amount of bluetooth traffic,
using the shared antenna (antenna B) will have
adverse impact on both bluetooth and wireless
traffic. Add controls to improve the situation
by making rate scaling depend on the BT load.

When there's high bluetooth traffic load, there's
little point in trying to aggregate as BT traffic
would disrupt the aggregated frames all the time,
so simply don't start sessions then.

When BT traffic returns to lower levels, the rate
scaling will come here again automatically when
wifi traffic is high enough, and then it will be
able to successfully enable aggregation.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-25 14:33:22 -04:00
Wey-Yi Guy
80e9158c3f iwlagn: continue perform rate scale when error detected
If for some reason, the actual link command not matching neither
active nor search table; instead of return and not performing rate
scale, by-pass the data collection and continue the rate scale process.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-08-24 16:32:02 -04:00
Wey-Yi Guy
b1a78858c4 iwlagn: adjust starting action for rate scale
During rate scale, reset starting action after making action adjustment
to avoid the possibility of break out of loop too early.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-08-24 16:32:01 -04:00
Wey-Yi Guy
7469701e10 iwlwifi: make aggregation time limit configurable
By default, aggregation time limit is 4000 uSec, add the parameter to
.cfg
to allow this parameter can be configure per device base if needed.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-08-24 16:32:00 -04:00
Andy Lutomirski
2411054ae9 iwlagn: Improve aggregation failure error messages
82ca934176 added scary looking
but harmless error messages.  Make them clearer and make the
actual failure message show up with the same severity as the
harmless one.

Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-08-04 15:30:55 -04:00
Wey-Yi Guy
cfecc6b492 iwlwifi: turn on RTS/CTS after aggregation become operational
If RTS/CTS protection is needed for HT, wait until get operational
notification from mac80211, then inform uCode to switch to RTS/CTS
through RXON command.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-06-25 15:20:41 -07:00
Johannes Berg
6a8579d0e6 mac80211: clean up ieee80211_stop_tx_ba_session
There's no sense in letting anything but internal
mac80211 functions set the initiator to anything
but WLAN_BACK_INITIATOR, since WLAN_BACK_RECIPIENT
is only valid when we have received a frame from
the peer, which we react to directly in mac80211.

The debugfs code I recently added got this wrong
as well.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-06-03 14:10:45 -04:00
Joe Perches
a4b770972b drivers/net: Remove unnecessary returns from void function()s
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.

It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.

It also does not remove null void functions with return.

Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
  xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'

with some cleanups by hand.

Compile tested x86 allmodconfig only.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-14 00:19:28 -07:00
John W. Linville
83163244f8 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
	drivers/net/wireless/libertas_tf/cmd.c
	drivers/net/wireless/libertas_tf/main.c
2010-05-05 16:14:16 -04:00
Reinette Chatre
3d79b2a9ee iwlwifi: recalculate average tpt if not current
We currently have this check as a BUG_ON, which is being hit by people.
Previously it was an error with a recalculation if not current, return that
code.

The BUG_ON was introduced by:
commit 3110bef78c
Author: Guy Cohen <guy.cohen@intel.com>
Date:   Tue Sep 9 10:54:54 2008 +0800

    iwlwifi: Added support for 3 antennas

... the portion adding the BUG_ON is reverted since we are encountering the error
and BUG_ON was created with assumption that error is not encountered.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-05-04 13:24:22 -04:00
Daniel Halperin
e3a3cd8789 iwlwifi: set AMPDU status variables correctly
The TX status code is currently abusing the ampdu_ack_map field (a bitmap) to
count the number of successfully received frames.  The comments in mac80211.h
show there are actually three different, relevant variables, of which we are
currently using two, both incorrectly. Fix this by making

- ampdu_ack_len -> the number of ACKed frames (i.e. successes)
- ampdu_ack_map -> the bitmap
- ampdu_len -> the total number of frames sent (i.e., attempts)

to match the header file (and verified with ath9k's usage) and updating Intel's
RS code to match.

Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-04-30 15:34:31 -07:00
John W. Linville
3b51cc996e Merge branch 'master' into for-davem
Conflicts:
	drivers/net/wireless/ath/ath9k/phy.c
	drivers/net/wireless/iwlwifi/iwl-6000.c
	drivers/net/wireless/iwlwifi/iwl-debugfs.c
2010-04-23 14:43:45 -04:00
Wey-Yi Guy
82ca934176 iwlwifi: sanity check for turn on aggregation tid
Perform sanity check for turn on aggregation tid. Also remove the
option for turn on all the aggregation tids at once since it is
deprecated function and not being used.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-04-16 13:53:06 -07:00
Wey-Yi Guy
3a23d69582 iwlwifi: set correct single/dual stream mask
Even the initial single/dual stream values will be overridden later when
issue link quality command; but still make sense not to use hard-code
value during initialization. Single/Dual stream mask are used to indicate the
best antenna for SISO/MIMO; different NIC has different tx antenna
configuration; so the parameter need to based on the valid tx antenna.

1x2 device: single tx antenna available, only SISO is valid
configuration, but still need to set up MIMO configuration, so set it up
with antenna A & B as default.
2x2 device: two tx antenna available, dual_stream will use both valid
antenna.

3x3 device: three tx antenna available, skip the first antenna and
choice the second and third antenna for dual_stream.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-04-16 13:46:29 -07:00
John W. Linville
5c01d56693 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
	Documentation/feature-removal-schedule.txt
	drivers/net/wireless/ath/ath5k/phy.c
	drivers/net/wireless/wl12xx/wl1271_main.c
2010-04-15 16:21:34 -04:00
David S. Miller
871039f02f Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/stmmac/stmmac_main.c
	drivers/net/wireless/wl12xx/wl1271_cmd.c
	drivers/net/wireless/wl12xx/wl1271_main.c
	drivers/net/wireless/wl12xx/wl1271_spi.c
	net/core/ethtool.c
	net/mac80211/scan.c
2010-04-11 14:53:53 -07:00
David S. Miller
4a1032faac Merge branch 'master' of /home/davem/src/GIT/linux-2.6/ 2010-04-11 02:44:30 -07:00
Reinette Chatre
f875f5183b iwlwifi: fix compile warnings when compiling without debug
Fixes:
CC [M]  drivers/net/wireless/iwlwifi/iwl-agn-rs.o
drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In function ‘rs_get_rate’:
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2419: warning: unused variable ‘priv’
CC [M]  drivers/net/wireless/iwlwifi/iwl-sta.o
drivers/net/wireless/iwlwifi/iwl-sta.c: In function ‘iwl_send_add_sta’:
drivers/net/wireless/iwlwifi/iwl-sta.c:197: warning: unused variable ‘sta_id’

drivers/net/wireless/iwlwifi/iwl-3945.c: In function ‘iwl3945_rx_reply_rx’:
drivers/net/wireless/iwlwifi/iwl-3945.c:601: warning: unused variable ‘rx_stats_noise_diff’
drivers/net/wireless/iwlwifi/iwl-3945.c:600: warning: unused variable ‘rx_stats_sig_avg’
drivers/net/wireless/iwlwifi/iwl-3945-rs.c: In function ‘rs_get_rate’:
drivers/net/wireless/iwlwifi/iwl-3945-rs.c:650: warning: unused variable ‘priv’

Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-04-09 11:32:36 -07:00
John W. Linville
0f2df9eac7 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into merge
Conflicts:
	Documentation/feature-removal-schedule.txt
	drivers/net/wireless/ath/ath5k/phy.c
	drivers/net/wireless/iwlwifi/iwl-4965.c
	drivers/net/wireless/iwlwifi/iwl-agn.c
	drivers/net/wireless/iwlwifi/iwl-core.c
	drivers/net/wireless/iwlwifi/iwl-core.h
	drivers/net/wireless/iwlwifi/iwl-tx.c
2010-04-08 13:34:54 -04:00
Frans Pop
91dd6c27a2 iwlwifi: remove trailing space in messages
Includes minor improvements in debugging messages in iwl-4965.c,
function iwl4965_is_temp_calib_needed().

Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Intel Linux Wireless <ilw@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-04-02 12:53:54 -07:00
Shanyu Zhao
04f2dec1c3 iwlwifi: use consistent table for tx data collect
When collecting tx data for non-aggregation packets in rate scaling, if
the tx data matches "other table", it still uses current table to update
the stats and calculate average throughput in function rs_collect_tx_data().
This can mess up the rate scaling data structure and cause a kernel panic
in a BUG_ON statement in rs_rate_scale_perform().

To fix this bug, we pass table pointer instead of window pointer (pointed
to by table pointer) to function rs_collect_tx_data() so that the table
being used is consistent.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Henry Zhang <hongx.c.zhang@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-04-02 11:12:37 -07:00
Tejun Heo
5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Johannes Berg
ed1b6e99b5 iwlwifi: remove noise reporting
We go to great lengths to calculate this value
that is never used by mac80211. Additionally,
it is now deprecated by mac80211 and is causing
driver compilation to give warnings.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-03-25 11:20:44 -07:00
Johannes Berg
fe0b3b96ab iwlwifi: sta_id cannot be invalid in rs_initialize_lq
The only caller of this is iwl_rs_rate_init
which is only called with a valid sta_id.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-03-19 13:41:07 -07:00
Reinette Chatre
fe6b23dd36 iwlwifi: implement new mac80211 station add/remove calls
mac80211 recently implemented two new callbacks that are used to request
station add/remove from the driver. The benefot from these new callbacks
are that they enable the driver to sleep while performing this work.

This is a big patch since a few things need to be coordinated in this move.
First we need to decouple station management from rate scaling, which
caused a lot of code to be moved and/or deleted. Next we needed to tie in
with mac80211's station management callback and let it direct our station
management as well as trigger the rate scaling initialization.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-03-19 13:40:58 -07:00
Johannes Berg
4a02886bae iwlwifi: remove priv->active_rate_basic
This variable is assigned a default value,
but then assigned zero as soon as mac80211
calls a change channel (which will happen
right after the hw is started) and after
that it never changes again.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-03-09 16:04:54 -08:00
Johannes Berg
e99f168c7c iwlagn: remove write-only variables
Updating the variables last_rx_rssi, last_tsf
and last_beacon_time needs a lot of code but
they are not actually used in iwlagn (only in
3945) so we can move them to the 3945 specific
data.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-03-09 16:03:53 -08:00
Wey-Yi Guy
45d427001b iwlwifi: check for aggregation frame and queue
Error checking for aggregation frames should go into aggregation queue,
if aggregation queue not available, use legacy queue instead.
Also make sure the aggregation queue is available to activate,
if driver and mac80211 is out-of-sync, try to disable the queue and
sync-up with mac80211.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
2010-02-11 10:26:10 -08:00
Reinette Chatre
1f44780827 iwlwifi: update copyright year to 2010
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-01-19 16:25:15 -05:00
Tobias Klauser
79496738eb iwlwifi: Storage class should be before const qualifier
The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:19:56 -05:00
Wey-Yi Guy
43e851157a iwlwifi: set read/write permission for debugfs files
Set the correct Read/Write file permission for iwlwifi debugfs files
based on the functionality of the files

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-23 17:05:33 -05:00
Johannes Berg
c951ad3550 mac80211: convert aggregation to operate on vifs/stas
The entire aggregation code currently operates on the
hw pointer and station addresses, but that needs to
change to make stations purely per-vif; As one step
preparing for that make the aggregation code callable
with the station, or by the combination of virtual
interface and station address.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18 17:09:15 -05:00
Reinette Chatre
5ad13f8ce7 iwlagn: move rate scale initialization to init function
This fits better in how the callbacks operate (alloc does allocation and
init does initialization). This also helps if we later want to do our own
initialization without relying on the mac80211 allocation.

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-02 15:39:47 -05:00