4 macros already defined in hdmi.h,
which is not required to redefine in hdmi_audio.c
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of linking encoders and bridges in every driver (and getting it
wrong half of the time, as many drivers forget to set the drm_bridge
encoder pointer), do so in core code. The drm_bridge_attach() function
needs the encoder and optional previous bridge to perform that task,
update all the callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Stefan Agner <stefan@agner.ch> # For DCU
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # For atmel-hlcdc
Acked-by: Vincent Abriou <vincent.abriou@st.com> # For STI
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # For sun4i
Acked-by: Xinliang Liu <z.liuxinliang@hisilicon.com> # For hisilicon
Acked-by: Jyri Sarha <jsarha@ti.com> # For tilcdc
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481709550-29226-4-git-send-email-laurent.pinchart+renesas@ideasonboard.com
On the userspace side, all the basics are working, and most of glmark2
is working. I've been working through deqp, and I've got a couple more
things to fix (but we've gone from 70% to 80+% pass in last day, and
current deqp run that is going should pick up another 5-10%). I expect
to push the mesa patches today or tomorrow.
There are a couple more a5xx related patches to take the gpu out of
secure mode (for the devices that come up in secure mode, like the hw
I have), but those depend on an scm patch that would come in through
another tree. If that can land in the next day or two, there might
be a second late pull request for drm/msm.
In addition to the new-shiny, there have also been a lot of overlay/
plane related fixes for issues found using drm-hwc2 (in the process of
testing/debugging the atomic/kms fence patches), resulting in rework
to assign hwpipes to kms planes dynamically (as part of global atomic
state) and also handling SMP (fifo) block allocation atomically as
part of the ->atomic_check() step. All those patches should also help
out atomic weston (when those patches eventually land).
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (36 commits)
drm/msm: gpu: Add support for the GPMU
drm/msm: gpu: Add A5XX target support
drm/msm: Disable interrupts during init
drm/msm: Remove 'src_clk' from adreno configuration
drm/msm: gpu: Add OUT_TYPE4 and OUT_TYPE7
drm/msm: Add adreno_gpu_write64()
drm/msm: gpu Add new gpu register read/write functions
drm/msm: gpu: Return error on hw_init failure
drm/msm: gpu: Cut down the list of "generic" registers to the ones we use
drm/msm: update generated headers
drm/msm/adreno: move scratch register dumping to per-gen code
drm/msm/rd: support for 64b iova
drm/msm: convert iova to 64b
drm/msm: set dma_mask properly
drm/msm: Remove bad calls to of_node_put()
drm/msm/mdp5: move LM bounds check into plane->atomic_check()
drm/msm/mdp5: dump smp state on errors too
drm/msm/mdp5: add debugfs to show smp block status
drm/msm/mdp5: handle SMP block allocations "atomically"
drm/msm/mdp5: dynamically assign hw pipes to planes
...
The DSI/HDMI PLLs in MSM require resources like interface clocks, power
domains to be enabled before we can access their registers.
The clock framework doesn't have a mechanism at the moment where we can
tie such resources to a clock, so we make sure that the KMS driver enables
these resources whenever a PLL is expected to be in use.
One place where we can't ensure the resource dependencies are met is when
the clock framework tries to disable unused clocks. The KMS driver doesn't
know when the clock framework calls the is_enabled clk_op, and hence can't
enable interface clocks/power domains beforehand.
We set the CLK_IGNORE_UNUSED flag for PLL clocks for now. This needs to be
revisited, since bootloaders can enable display, and we would want to
disable the PLL clocks if there isn't a display driver using them.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make the following changes in the HDMI gpio bindings:
- Use "-gpios" as the suffix for all the gpio names
- Move all the gpios to optional, since there are platforms that use none
of them.
- The HPD gpio is a standard one, remove the "qcom,hdmi-tx-" prefix from
it.
- Remove the HDMI DDC clk/data gpios. They are just leftovers of an old
way to configure pinctrl properties.
- Add a missing lpm gpio used on some platforms.
Make the necessary changes in the driver to incorporate these changes.
There hasn't been any upstream DT that uses the HDMI bindings, so it's
okay to change and move around these properties.
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR.
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This patch adds support to generic audio codec via
ASoC hdmi-codec infrastucture which is merged recently.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[rebased on efc9194]
Signed-off-by: Rob Clark <robdclark@gmail.com>
For all outputs except DSI we have a 1:1 relationship between connectors
and encoders and the driver is relying on the atomic helpers: we can
drop the custom ->best_encoder() and let the core call
drm_atomic_helper_best_encoder() for us.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-9-git-send-email-boris.brezillon@free-electrons.com
Move the drm_connector registration from the encoder(HDMI/DSI etc) drivers
to the msm platform driver. This will simplify the task of ensuring that
the connectors are registered only after the drm_device itself is
registered.
The connectors' destroy ops are made to use kzalloc instead of
devm_kzalloc to ensure that that the connectors can be successfully
unregistered when the msm driver module is removed. The memory for the
connectors is unallocated when drm_mode_config_cleanup() is called
during either during an error or during driver remove.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Calling the legacy gpio_free on an invalid GPIO (a GPIO numbered -1)
results in kernel warnings. This causes a lot of backtraces when
we try to unload the drm/msm module.
Call gpio_free only on valid GPIOs.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Global symbols in the kernel should be prefixed by the name
of the subsystem and/or driver to avoid conflicts when all
code is built-in.
In this case, function names like 'hdmi_register' or 'hdmi_set_mode'
are way too generic for an MSM specific DRM driver, so I'm renaming
them all to msm_hdmi_* here.
I also rename a lot of the 'static' symbols along with the global
names for consistency, even though those are relatively harmless;
they might only be slightly confusing when they show up in
backtraces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support for the HDMI PHY/PLL found in MSM8996/APQ8096.
Unlike the previous PHYs supported in the driver, this doesn't need
the powerup/powerdown ops. The PLL prepare/unprepare clock ops
enable/disable the phy itself.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
- Create separate domains for 8960 PHY and PLL
- Create separate domains for 8x60 PHY
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Remove the old PHY ops managed by hdmi_platform_config and use them as ops
provided by the HDMI PHY driver.
Remove the old HDMI 8960 PLL code that used the top level HDMI TX mmio
base.
NOTE: With this commit, HDMI functionality will break until the HDMI
PHY/PLL register offsets in hdmi.xml.h aren't updated to be used as
separate domains.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make HDMI core get its PHY by parsing the "phys" phandle. The core will use
this PHY reference to enable/disable PHY. The driver defers probe until PHY
isn't available.
The DT bindings used here is the same as the one used for PHYs using the
common PHY framework bindings.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a helper to initialize PLL in the PHY driver. HDMI PLLs are going to
have their own mmio base different from that of PHY.
For the clock code in hdmi_phy_8960.c, some changes were needed for it to
work with the updated register offsets. Create a copy of the updated clock
code in hdmi_pll_8960.c, instead of rewriting it in hdmi_phy_8960.c
itself. This removes the need to place CONFIG_COMMON_CLOCK checks all
around, makes the code more legible, and also removes some old checkpatch
warnings with the original code.
The older hdmi pll clock ops in hdmi_phy_8960.c will be removed later. The
driver will use these until the HDMI PHY/PLL register offsets aren't
considered as separate domains (i.e. their offsets start from 0).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create a PHY device that represents the TX PHY and PLL parts of the HDMI
block.
This makes management of PHY specific resources (regulators and clocks)
much easier, and makes the PHY and PLL usable independently. It also
simplifies the core HDMI driver, which currently assigns phy ops among
many other things.
The PHY driver implementation done here is very similar to the PHY driver
we already have for DSI.
Keep the old hdmi_phy_funcs ops for now. The driver will use these until
the HDMI PHY/PLL register offsets aren't considered as separate
domains (i.e. their offsets start from 0).
The driver doesn't use the common PHY framework for now. This is because
it's hard to map our ops with the ops provided by the framework. The
bindings used for this is the generic phy bindings. So, this can be
adapted to the PHY framework in the future, if possible.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some platforms may not have a HPD gpio line to detect Hot Plug signal from
the connector. They need to rely only on reading REG_HDMI_HPD_INT_STATUS
for HPD.
Modify hdmi_connector_detect logic such that it checks for HPD only using
the status register if there is no HPD gpio.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Make gpio allocation and usage iterative by parsing the gpios on a given
platform from a list. This gives us flexibility over what all gpios exist
for a platform, whether they are input or output, and what value they
should be set to.
In particular, this will make HDMI on 8x96 platforms easier to integrate
with the driver, as it doesn't have a HPD gpio input to them. Also, it
cleans things up a bit.
We still use the legacy gpio api here, as we might need to backport this
driver to downstream kernels.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We now only care about kernels that support DT. Remote the non-DT stuff.
While we're at it, use of_device_get_match_data to retrieve match data.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The HDMI controller is new in MDP5 v1.7. As of now, this change
doesn't reflect the novelty and only adds the basics so the probe
gets triggered.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For all of these devices, msm89xy was the lead chip, so standardize the
compatible names to align with convention used by rest of the qcom/msm
drivers.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the MDP and HDMI support for msm8x94.
Note that HDMI PHY registers are not being accessed anymore from
the driver.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[rename compatible s/8x94/8994/ since preference is to not trust the
marketing folks who invent chip #'s but instead name things after the
lead chip.. we should rename some 80XY to 89XY to standardize on the
lead chip but leave that for another patch. Also, update dt bindings
doc]
Signed-off-by: Rob Clark <robdclark@gmail.com>
->reset() currently only accesses HDMI core registers, and yet it
is located in hdmi_phy*. Since no PHY registers are being
accessed during ->reset(), it would be better to bring that
function in hdmi core module where HDMI core registers are
usually being accessed.
This will also help for msm8x94 for which no PHY registers
accesses are done (->phy_init == NULL) but the HDMI PHY reset
from HDMI core still needs to be done.
Note:
SW_RESET_PLL bit is not written in hdmi_phy_8x60_reset(); this
write should not affect anything if the corresponding field is
not writable.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[fixed warning about unused 'phy' in hpd_enable() while merging]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add HDMI HDCP support including HDCP PartI/II/III authentication.
V1: Initial Change
V2: Address Bjorn&Rob's comments
Refactor the authentication process to use single work instead
of multiple work for different authentication stages.
V3: Update to align with qcom SCM api.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some targets (eg: msm8994) use the pinctrl framework to configure
interface pins. This change adds support for initialization and
pinctrl active/sleep state control for the HDMI driver.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DRM device's dev (hdmi->dev->dev) points to the mdss_mdp device
handle. Instead, we should get a reference to the mdss_hdmi
handle.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
So after clarification from qcom, it seems mdp4 and mdp5 support
*de*interlacing but not generating an interlaced signal. Which would
explain why interlaced modes never worked properly.
So disable in the one connector which was claiming to support
interlaced.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In the same idea mdp5_cfg was added, this change allows us to quickly
add new instances, such as apq8084's HDMI in this case.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change add the regulator/clock configuration for MDP5 v1.3.
This config is close to the one already existing for 8x74, except
that one more regulator is needed (hpd-5v-en).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of reporting BUG_ON when resources arrays are not
dimensioned correctly, this patch does a dynamic allocation of
these arrays. This is needed for the following patches that add a
regulator for a new target.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Resync from rnndb database, to pull in register defines for:
* eDP
* HDMI/HDCP
* mdp4/mdp5 YUV support
* mdp5 hw cursor support
Signed-off-by: Rob Clark <robdclark@gmail.com>
3d3f8b1f8b ("drm/bridge: make bridge registration independent of drm
flow") resulted that the hdmi bridge object would be leaked at teardown.
Just switch over to devm_kzalloc() as the easy way to solve this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
As a result of atomic DPMS support, the various prepare/commit hooks get
called in a way that msm dislikes. We were expecting prepare/commit to
bracket a modeset, which is no longer the case. This was needed to hold
various extra clk's (such as interface clks) on while we are touching
registers, and in the case of mdp4 holding vblank enabled.
The most straightforward way to deal with this, since we already have
our own atomic_commit(), is to just handle prepare/commit internally to
the driver (with some additional vfuncs for mdp4 vs mdp5), and switch
everything over to instead use the new enable/disable hooks. It doesn't
really change too much, despite the code motion. What used to be in the
encoder/crtc dpms() fxns is split out into enable/disable.
We should be able to drop our own enable-state tracking, as the atomic
helpers should do this for us. But keeping that for the short term for
extra debugging as atomic stablizes.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently, third party bridge drivers(ptn3460) are dependent
on the corresponding encoder driver init, since bridge driver
needs a drm_device pointer to finish drm initializations.
The encoder driver passes the drm_device pointer to the
bridge driver. Because of this dependency, third party drivers
like ptn3460 doesn't adhere to the driver model.
In this patch, we reframe the bridge registration framework
so that bridge initialization is split into 2 steps, and
bridge registration happens independent of drm flow:
--Step 1: gather all the bridge settings independent of drm and
add the bridge onto a global list of bridges.
--Step 2: when the encoder driver is probed, call drm_bridge_attach
for the corresponding bridge so that the bridge receives
drm_device pointer and continues with connector and other
drm initializations.
The old set of bridge helpers are removed, and a set of new helpers
are added to accomplish the 2 step initialization.
The bridge devices register themselves onto global list of bridges
when they get probed by calling "drm_bridge_add".
The parent encoder driver waits till the bridge is available
in the lookup table(by calling "of_drm_find_bridge") and then
continues with its initialization.
The encoder driver should also call "drm_bridge_attach" to pass
on the drm_device to the bridge object.
drm_bridge_attach inturn calls "bridge->funcs->attach" so that
bridge can continue with drm related initializations.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Assign the pointer to bridge ops structure(drm_bridge_funcs) in
the bridge driver itself, instead of passing it to drm_bridge_init.
This will allow bridge driver developer to pack bridge private
information inside the bridge object and pass only the drm-relevant
information to drm_bridge_init.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A left-over from prior to component framework. The original intent was
to deal with hdmi getting unloaded before the master component, but that
isn't really going to work anyways. These days with the component
framework taking care to unload the master component first, we don't
have to worry about this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
