Mali DP500 operates in continuous writeback mode (writes frame content
until stopped) and it needs special handling in order to behave like
a one-shot writeback engine. The original state machine added for DP500
was a bit fragile, as it did not handle correctly cases where a new
atomic commit was in progress when the SE IRQ happens and it would
commit some partial updates.
Improve the handling by adding a parameter to the set_config_valid()
function to clear the config valid bit in hardware before starting a
new commit and by introducing a MW_RESTART state in the writeback
state machine to cater for the case where a new writeback commit
gets submitted while the last one is still being active.
Reported-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali-DP has a memory writeback engine which can be used to write the
composition result to a memory buffer. Expose this functionality as a
DRM writeback connector on supported hardware.
Changes since v1:
Daniel Vetter:
- Don't require a modeset when writeback routing changes
- Make writeback connector always disconnected
Changes since v2:
- Rebase onto new drm_writeback_connector
- Add reset callback, allocating subclassed state
Daniel Vetter:
- Squash out-fence support into this commit
Gustavo Padovan:
- Don't signal fence directly from driver (and drop malidp_mw_job)
Changes since v3:
- Modifications to fit with Mali-DP commit tail changes
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[rebased and fixed conflicts]
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Annotate the pixel format matrix for DP500 with the memory-write flag
for formats that are supported by the SE memwrite engine.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP500 behaves differently from the rest of the Mali DP IP,
in that it does not have a one-shot mode and keeps writing the
content of the current frame to the provided memory area until
stopped. As a way of emulating the one-shot behaviour, we are
going to use the CVAL interrupt that is being raised at the
start of each frame, during prefetch phase, to act as End-of-Write
signal, but with a twist: we are going to disable the memory
write engine right after we're notified that it has been enabled,
using the knowledge that the bit controlling the enabling will
only be acted upon on the next vblank/prefetch.
CVAL interrupt will fire durint the next prefetch phase every time
the global CVAL bit gets set, so we need a state byte to track
the memory write enabling. We also need to pay attention during the
disabling of the memory write engine as that requires the CVAL bit
to be set in the control register, but we don't want to do that
during an atomic commit, as it will write into the hardware a partial
state.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Add a layer bit for the SE memory-write, and add it to the pixel format
matrix for DP550/DP650.
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[rebased and fixed conflicts]
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali-DP display processors are able to write the composition result to a
memory buffer via the SE.
Add entry points in the HAL for enabling/disabling this feature, and
implement support for it on DP650 and DP550. DP500 acts differently and
so is omitted from this change.
Changes since v3:
- Fix missing vsync interrupt for DP550
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[rebased and fixed conflicts]
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
In the situation that DE and SE aren’t shared the same interrupt number,
the Global SE interrupts mask bit MASK_IRQ_EN in MASKIRQ must be set, or
else other mask bits will not work and no SE interrupt will occur. This
patch enables MASK_IRQ_EN for SE to fix this problem.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Internally Mali DP uses an RGB pipeline so video layers that support
YUV input buffers need to convert the input data to RGB. The YUV
buffers can have various encodings and this patch introduces support
for BT.601, BT.709 and BT.2020 encodings, both limited and full ranges.
This patch adds support for specifying the color encoding of the
input buffers for the planes that are backed by the video layers
and programs the YUV2RGB coefficients into hardware based on the
selected encoding.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[updated to use standard properties]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Mali DP hardware has a 'go' bit (config_valid) for making the new scene
parameters active at the next page flip. The problem with the current
code is that the driver first sets this bit and then proceeds to wait
for confirmation from the hardware that the configuration has been
updated before arming the vblank event. As config_valid is actually
asserted by the hardware after the vblank event, during the prefetch
phase, when we get to arming the vblank event we are going to send it
at the next vblank, in effect halving the vblank rate from the userspace
perspective.
Fix it by sending the userspace event from the IRQ handler, when we
handle the config_valid interrupt, which syncs with the time when the
hardware is active with the new parameters.
Reported-by: Alexandru-Cosmin Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
The malidp_hw_device structure that the driver uses to handle the
differences between versions of the IP contains both non-changeable
data and fields that get updated at probe time. Previously we were
copying the read-only part into allocated memory, but that can be
completely avoided by splitting the structure into a read-only part
and keeping the runtime modifiable fields into the old structure.
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
If an instance of Mali DP hardware shares the interrupt line with
another hardware (usually another instance of the Mali DP) its
interrupt handler can get called when the device is suspended.
Check the PM status before making access to the hardware registers
to avoid deadlocks.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
When downscaling, mclk needs to be sufficiently higher than pxlclk in
order to be able to fetch the higher-resolution data and produce output
pixels. When not scaling, or when upscaling, mclk can be equal to
pxlclk. Since the driver doesn't control mclk, just ensure that the
requirement is satisfied with the current clock rate.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Enable the scaling engine for upscaling a single plane using the polyphase
scaler. No image enhancement support or downscaling yet*, and composition
result scaling is not implemented.
* Downscaling a plane requires mclk > pxlclk.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add gamma via the DRM GAMMA_LUT/GAMMA_LUT_SIZE CRTC
properties. The expected LUT size is 4096 in order
to produce as accurate a set of segments as possible.
This version uses only the green channel's gamma curve
to set the hardware curve on DP550/650. For the sake of
simplicity, it uses the same table of coefficients for
all 3 curves on DP500.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Use rectangle 1 as a generic plane. Existing code already sets the smart
layer bounding box size + offset. The rectangles' offsets are relative
to the bounding box, so there is no need to set R1's offset (reset value
is 0), just its size which is the same as the bounding box.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Hardware has multiple (2 or 3, depending on model) stride
registers per layer; add a function that correctly takes that
into account. On hardware that only has 2 stride registers,
ensure that 3-plane (YUV) content has identical strides
for both chroma planes.
Signed-off-by: Mihail Atanassov <mihail.atanassov@arm.com>
[Removed smart layer stride setup, comment and commit message clarifications]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
We're going to use the same format list for output formats, so rename
everything related to input formats to avoid confusion.
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
[touched commit title to clarify the final struct name]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
It's possible for CVAL to get set whilst we are in config mode. If this
happens, afer we leave config mode the HW will latch whatever
configuration is in the registers at the next vsync. Most likely this
will be a partial configuration, as we'll be racing against the ongoing
atomic_commit.
To avoid this, clear CVAL before leaving config mode.
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Different hardware versions have different requirements when it comes to
pitch alignment. Add a function which can be used to check pitch
alignment for a device.
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Add support for the new family of Display Processors from ARM Ltd.
This commit adds basic support for Mali DP500, DP550 and DP650
parts, with only the display engine being supported at the moment.
Cc: David Brown <David.Brown@arm.com>
Cc: Brian Starkey <Brian.Starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
