Commit Graph

11 Commits

Author SHA1 Message Date
Arnd Bergmann
4bdb96cb69 qed: select ZLIB_INFLATE
The newly added qlogic qed driver uses the zlib library, but
misses the dependency:

drivers/built-in.o: In function `qed_alloc_stream_mem':
drivers/net/ethernet/qlogic/qed/qed_main.c:707: undefined reference to `zlib_inflate_workspacesize'
drivers/built-in.o: In function `qed_unzip_data':
drivers/net/ethernet/qlogic/qed/qed_main.c:675: undefined reference to `zlib_inflateInit2'

This changes Kconfig to always select zlib when needed.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-10 15:39:03 -05:00
Yuval Mintz
e712d52b9f qede: Add basic Network driver
The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.

This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-27 19:34:47 -07:00
Yuval Mintz
fe56b9e6a8 qed: Add module with basic common support
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.

This module serves two main purposes:
 1. It's responsible to contain all the common code that will be shared
    between the various drivers that would be used with said line of
    products. Flows such as chip initialization and de-initialization
    fall under this category.

 2. It would abstract the protocol-specific HW & FW components, allowing
    the protocol drivers to have a clean APIs which is detached in its
    slowpath configuration from the actual HSI.

This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-27 19:34:42 -07:00
Paul Gortmaker
138b15ed87 drivers/net: remove all references to obsolete Ethernet-HOWTO
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it.  And there is
no value in anyone else taking over updating it either.

However the references to it continue to spread as boiler plate text
from one Kconfig file into the next.  We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.

No code is changed in this commit, just Kconfig help text.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-23 06:50:35 -07:00
Harish Patil
f398a77177 qlcnic: Fix Kconfig dependency on HWMON
Commit 1f0f467b67 "qlcnic: Add hwmon interface to export board
temperature" introduced a randconfig build error in the case
when the hwmon framework is built as a module and the qlcnic
driver itself is built-in:

drivers/built-in.o: In function `qlcnic_register_hwmon_dev':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sysfs.c:1301:
undefined reference to `hwmon_device_register_with_groups'
drivers/built-in.o: In function `qlcnic_unregister_hwmon_dev':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sysfs.c:1309:
undefined reference to `hwmon_device_unregister'.

This changes the Kconfig logic to enforce that the qlcnic hwmon
support can only be enabled if it is possible to successfully
build it.

Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-07 17:23:25 -04:00
Harish Patil
1f0f467b67 qlcnic: Add hwmon interface to export board temperature.
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-27 23:20:53 -04:00
Shahed Shaikh
7f1f6056f2 qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
Commit 2b3d7b758c687("qlcnic: Add VXLAN Rx offload support") uses
vxlan_get_rx_port() which caused build failure when VXLAN=m.

This patch fixes the build failure by adding dependency on VXLAN
in Kconfig of qlcnic module and use vxlan_get_rx_port() and support
code accordingly.

Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-01 17:38:05 -04:00
Sucheta Chakraborty
14d385b990 qlcnic: dcb: Query adapter DCB capabilities.
o Query adapter DCB capabilities and  populate local data structures
  with relevant information.

o Add QLCNIC_DCB to Kconfig for enabling/disabling DCB.

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-27 15:21:13 -04:00
Rajesh Borundia
02feda1758 qlcnic: Support SR-IOV enable and disable
o Add QLCNIC_SRIOV to Kconfig.
o Provide PCI sysfs hooks to enable and disable SR-IOV.
o Allow enabling only when CONFIG_QLCNIC_SRIOV is defined.
o qlcnic_sriov_pf.c has all the PF related SR-IOV
  functionality.
o qlcnic_sriov_common.c has VF functionality and SR-IOV
  functionality which is common between VF and PF.
o qlcnic_sriov.h is a common header file for SR-IOV defines.

Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-29 15:46:08 -04:00
Jeff Kirsher
88f07484cc drivers/net/ethernet/*: Enabled vendor Kconfig options
Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.

This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers.  In
addition, by enabling all the new Kconfig options does not add
any un-expected options.

CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-08-27 00:58:56 -07:00
Jeff Kirsher
aa43c2158d qlogic: Move the QLogic drivers
Moves the QLogic drivers into drivers/net/ethernet/qlogic/ and
the necessary Kconfig and Makefile changes.

CC: Ron Mercer <ron.mercer@qlogic.com>
CC: Amit Kumar Salecha <amit.salecha@qlogic.com>
CC: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
2011-08-10 20:03:49 -07:00