i2c_gpio_getsda() and i2c_gpio_getscl() are only used in this file.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use i2c_bit_add_numbered_bus() so that the i2c-gpio adapter works well
with new-style pre-declared devices.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update the IOP3xx I2C driver to use i2c_add_numbered_adapter(), so that
later patches can convert boards to using new-style drivers.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Tested-by: Voipio Riku <Riku.Voipio@movial.fi>
Cc: Dan J Williams <dan.j.williams@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the i2c-sis5595 driver release its PCI device after registering.
This is to allow the sis5595 hardware monitoring driver to also
access this PCI device. The same trick is already used in the
i2c-viapro and via686a drivers to let them both load.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
matroxfb_crtc2 has nothing to do with i2c, so there's no reason why
matroxfb_crtc2.h should include i2c header files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <vandrove@vc.cvut.cz>
Add support for SMBus block read/write transactions to i2c-nforce2
driver, in particular to host controllers MCP51 and MCP55.
Signed-off-by: Oleg Ryjkov <olegr@google.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the i2c-mpc driver over to using the new i2c infrastructure.
Specifically, it now uses i2c_add_numbered_adapter so that the bus number
can be determined ahead of time and used to register i2c clients before
the bus is instantiated.
Tested on an MPC5200 based board
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert the Marvell mv64xxx I2C driver to use the new i2c infrastructure,
by calling i2c_add_numbered_adapter(). This allows clients to be
registered before the bus is instantiated.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
A driver for the Dallas DS1682 elapsed time recorder chip.
Tested on a MPC5200 based board using the integrated i2c adapter.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the drivers specify how many bytes they want to read with
i2c_smbus_read_i2c_block_data(). So far, the block count was
hard-coded to I2C_SMBUS_BLOCK_MAX (32), which did not make much sense.
Many driver authors complained about this before, and I believe it's
about time to fix it. Right now, authors have to do technically stupid
things, such as individual byte reads or full-fledged I2C messaging,
to work around the problem. We do not want to encourage that.
I even found that some bus drivers (e.g. i2c-amd8111) already
implemented I2C block read the "right" way, that is, they didn't
follow the old, broken standard. The fact that it was never noticed
before just shows how little i2c_smbus_read_i2c_block_data() was used,
which isn't that surprising given how broken its prototype was so far.
There are some obvious compatiblity considerations:
* This changes the i2c_smbus_read_i2c_block_data() prototype. Users
outside the kernel tree will notice at compilation time, and will
have to update their code.
* User-space has access to i2c_smbus_xfer() directly using i2c-dev, so
the changed expectations would affect tools such as i2cdump. In order
to preserve binary compatibility, we give I2C_SMBUS_I2C_BLOCK_DATA
a new numeric value, and define I2C_SMBUS_I2C_BLOCK_BROKEN with the
old numeric value. When i2c-dev receives a transaction with the
old value, it can convert it to the new format on the fly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We have a new RTC subsystem with better drivers.
Legacy driver status:
* ds1337: The DS1337 and DS1339 are now supported by the rtc-ds1307
driver, so it looks to me like we could even delete the ds1337
driver right away.
* ds1374: Will soon be replaced with Scott Wood's rtc-ds1374 driver.
* m41t00: The M41T00 is supported by the rtc-ds1307 driver. For the
M41T81 and M41T85, the rtc-m41t80 driver written by Atsushi Nemoto
should work.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: James Chapman <jchapman@katalix.com>
Cc: Randy Vinson <rvinson@mvista.com>
The x1205 driver moved to the RTC subsystem and was significantly
modified since then, so just delete the outdated documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
The scx200_acb driver use a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Generate I2C kerneldoc; fix various glitches and add "context" sections to
that documentation. Most I2C and SMBus functions still have no kerneldoc.
Let me suggest providing kerneldoc for all the i2c_smbus_*() functions as
a small and mostly self-contained project for anyone so inclined. :)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: at91_mci: fix hanging and rework to match flowcharts
mmc: at91_mci typo
sdhci: Fix "Unexpected interrupt" handling
mmc: fix silly copy-and-paste error
mmc: move layer init and workqueue to core file
mmc: refactor host class handling
mmc: refactor bus operations
sdhci: add ene controller id
mmc: bounce requests for simple hosts
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (40 commits)
bonding/bond_main.c: make 2 functions static
ps3: gigabit ethernet driver for PS3, take3
[netdrvr] Fix dependencies for ax88796 ne2k clone driver
eHEA: Capability flag for DLPAR support
Remove sk98lin ethernet driver.
sunhme.c:quattro_pci_find() must be __devinit
bonding / ipv6: no addrconf for slaves separately from master
atl1: remove write-only var in tx handler
macmace: use "unsigned long flags;"
Cleanup usbnet_probe() return value handling
netxen: deinline and sparse fix
eeprom_93cx6: shorten pulse timing to match spec (bis)
phylib: Add Marvell 88E1112 phy id
phylib: cleanup marvell.c a bit
AX88796 network driver
IOC3: Switch to pci refcounting safe APIs
e100: Fix Tyan motherboard e100 not receiving IPMI commands
QE Ethernet driver writes to wrong register to mask interrupts
rrunner.c:rr_init() must be __devinit
tokenring/3c359.c:xl_init() must be __devinit
...
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (32 commits)
[libata] sata_mv: print out additional chip info during probe
[libata] Use ATA_UDMAx standard masks when filling driver's udma_mask info
[libata] AHCI: Add support for Marvell AHCI-like chips (initially 6145)
[libata] Clean up driver udma_mask initializers
libata: Support chips with 64K PRD quirk
Add a PCI ID for santa rosa's PATA controller.
sata_sil24: sil24_interrupt() micro-optimisation
Add irq_flags to struct pata_platform_info
sata_promise: cleanups
[libata] pata_ixp4xx: kill unused var
ata_piix: fix pio/mwdma programming
[libata] ahci: minor internal cleanups
[ATA] Add named constant for ATAPI command DEVICE RESET
[libata] sata_sx4, sata_via: minor documentation updates
[libata] ahci: minor internal cleanups
[libata] ahci: Factor out SATA port init into a separate function
[libata] pata_sil680: minor cleanups from benh
[libata] sata_sx4: named constant cleanup
[libata] pata_ixp4xx: convert to new EH
[libata] pdc_adma: Reorder initializers with a couple structs
...
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] vmlogrdr function annotation.
[S390] s390: rename CPU_IDLE to S390_CPU_IDLE
[S390] cio: Remove prototype for non-existing function cmf_reset().
[S390] zcrypt: fix request timeout handling
[S390] system call optimization.
[S390] dasd: Avoid compile warnings on !CONFIG_DASD_PROFILE
[S390] Remove volatile from atomic_t
[S390] Program check in diag 210 under 31 bit
[S390] Bogomips calculation for 64 bit.
[S390] smp: Merge smp_count_cpus() and smp_get_save_areas().
[S390] zcore: Fix __user annotation.
[S390] fixed cdl-format detection.
[S390] sclp: Test facility list before executing a service call.
[S390] sclp: introduce some new interfaces.
[S390] Fixed comment typo.
[S390] vmcp cleanup
* 'splice-2.6.23' of git://git.kernel.dk/data/git/linux-2.6-block:
pipe: add documentation and comments
pipe: change the ->pin() operation to ->confirm()
Remove remnants of sendfile()
xip sendfile removal
splice: completely document external interface with kerneldoc
sendfile: remove bad_sendfile() from bad_file_ops
shmem: convert to using splice instead of sendfile()
relay: use splice_to_pipe() instead of open-coding the pipe loop
pipe: allow passing around of ops private pointer
splice: divorce the splice structure/function definitions from the pipe header
splice: relay support
sendfile: convert nfsd to splice_direct_to_actor()
sendfile: convert nfs to using splice_read()
loop: convert to using splice_direct_to_actor() instead of sendfile()
splice: add void cookie to the actor data
sendfile: kill generic_file_sendfile()
sendfile: remove .sendfile from filesystems that use generic_file_sendfile()
sys_sendfile: switch to using ->splice_read, if available
vmsplice: add vmsplice-to-user support
splice: abstract out actor data
* 'trivial-2.6.23' of git://git.kernel.dk/data/git/linux-2.6-block:
Documentation/block/barrier.txt is not in sync with the actual code: - blk_queue_ordered() no longer has a gfp_mask parameter - blk_queue_ordered_locked() no longer exists - sd_prepare_flush() looks slightly different
Use list_for_each_entry() instead of list_for_each() in the block device
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu",
block/Kconfig already has its own "menuconfig" so remove these
Use menuconfigs instead of menus, so the whole menu can be disabled at once
cfq-iosched: fix async queue behaviour
unexport bio_{,un}map_user
Remove legacy CDROM drivers
[PATCH] fix request->cmd == INT cases
cciss: add new controller support for P700m
[PATCH] Remove acsi.c
[BLOCK] drop unnecessary bvec rewinding from flush_dry_bio_endio
[PATCH] cdrom_sysctl_info fix
blk_hw_contig_segment(): bad segment size checks
[TRIVIAL PATCH] Kill blk_congestion_wait() stub for !CONFIG_BLOCK
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Chad Tindel <ctindel@users.sourceforge.net>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This is the third submission of the network driver for PS3.
The differences from the previous one are:
- renamed source file names so that their prefix can match
with the module name
- added cbe-oss-dev@ozlabs.org line for MAINTAINER file
- changed some in copyright comments
If there are no more comments, please apply for 2.6.23.
Thank you
--
Subject: PS3: Ethernet driver
From: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Add Gigabit Ethernet support for the PS3 game console. The module will
be called ps3_gelic.
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch introduces a capability flag that is used by the DLPAR userspace
tool to check which DLPAR features are supported by the eHEA driver.
Missing goto has been included.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At present, when a device is enslaved to bonding, if ipv6 is
active then addrconf will be initated on the slave (because it is closed
then opened during the enslavement processing). This causes DAD and RS
packets to be sent from the slave. These packets in turn can confuse
switches that perform ipv6 snooping, causing them to incorrectly update
their forwarding tables (if, e.g., the slave being added is an inactve
backup that won't be used right away) and direct traffic away from the
active slave to a backup slave (where the incoming packets will be
dropped).
This patch alters the behavior so that addrconf will only run on
the master device itself. I believe this is logically correct, as it
prevents slaves from having an IPv6 identity independent from the
master. This is consistent with the IPv4 behavior for bonding.
This is accomplished by (a) having bonding set IFF_SLAVE sooner
in the enslavement processing than currently occurs (before open, not
after), and (b) having ipv6 addrconf ignore UP and CHANGE events on
slave devices.
The eql driver also uses the IFF_SLAVE flag. I inspected eql,
and I believe this change is reasonable for its usage of IFF_SLAVE, but
I did not test it.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
usbnet_probe() handles a positive return value from the driver bind()
function as success, but will later only setup the status handler if the
return value was zero, leading to confusion. Patch adjusts this to accept
positive values as success in both checks.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Get rid of dubious casts to (void *) which causes a sparse warning.
And move largeish function from inline to the one file that uses the code,
the compiler can then decide to inline it.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Based on an original idea by John W. Linville.
It is the missing part of 42d45ccd60636c28e35c2016f091783bc14ad99c
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add 88E1112 PHY ID to the marvell driver. Seems to do fine with the
88E1111 inits.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify the marvell driver init a bit: Make the supported devices an
array instead of explicitly registering each structure. This makes it
considerably easier to add new devices down the road.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Support for the Asix AX88796 network controller, an
NE2000 compatible 10/100 ethernet device with internal
PHY.
The driver supports PHY settings via either ioctl() or
the ethtool driver ops.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
TX49XX SoCs include PCI NIC (TC35815 compatible) connected via its
internal PCI bus, but the NIC's PROM interface is not connected to
SEEPROM. So we must provide its ethernet address by another way.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the IOC3 driver to use ref counting pci interfaces so that we can
obsolete the (usually unsafe) pci_find_{slot/device} interfaces and avoid
future authors writing hotplug-unsafe device drivers.
Signed-off-by: Alan Cox <alan@redhat.com>
Build fixes:
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 82550 & 51 parts have an extended configuration block that
includes a bit "GMRC", required to enable the expected TCO behavior,
in config byte offset 22d. The config block sent by the failing driver
does include the extension area, but this bit is not initialised,
and the downlaod only specifies 0x16 bytes to be sent to the NIC
(thaht's bytes 00..21d). By initializing the GMRC bit, and extending
the download size for D102+ MACs, the problem is resolved.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The QE Ethernet driver was writing to the wrong register to mask interrupts.
In ucc_geth_stop(), it was clearing UCCE instead of UCCM.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
