[Why]
Per DP specification, YCbCr420 shall use VSC SDP.
[How]
For YCbCr420 timings, fail DP mode timing validation
if DPCD caps do not indicate VSC SDP colorimetry
support.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Sometimes, such as sleep wake, the link->local sink pointer changed,
but the dc_stream_state->sink pointer is not changed. The checking
of timing_changed reports wrong result, lead to link tear down
unexpected wrongly.
[How]
SST compare local sink, MST compare proper remote link.
Signed-off-by: Calvin Hou <Calvin.Hou@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Per DP spec, for active protocol convertor adaptor, DP source should enable audio
for DFP type is DP, HDMI or DP++. Current is_dp_active_dongle() checking is not
precise, which treat branch device default as active dongle. As a result, we will
mistakenly disable audio for DFP type is DP case.
[How]
Make is_dp_active_dongle() checking more precise for active dongle types.
Rename active diongle type as SST branch device in case confusion.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To process AUX transactions with DMUB using inbox1 and outbox1 mail boxes.
[How]
1) Added inbox1 command DMUB_CMD__DP_AUX_ACCESS to issue AUX commands
to DMUB in dc_process_dmub_aux_transfer_async(). DMUB processes AUX cmd
with DCN and sends reply back in an outbox1 message triggering an
outbox1 interrupt to driver.
2) In existing driver implementation, AUX commands are processed
synchronously by configuring DCN reg. But in DMUB AUX, driver sends an
inbox1 message and waits for a conditional variable (CV) which will be
signaled by outbox1 ISR.
3) DM will retrieve Outbox1 message and send back reply to upper layer
and complete the AUX command
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Hanghong Ma <Hanghong.Ma@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The split pipe config is updated due to antoher stream bandwidth
validataion. Driver doesn't reprogram the split pipe config
to signle pipe cause SW use signel pipe but HW still use pipe split.
[How]
track global updates and update any hw that isn't
related to current stream being updated.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Based on hardware team recommendation this additional dsc overhead
is only required for DP DSC.
[how]
Add a check for is_dp and only apply the overhead if this flag is set.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In commit 482812d566 ("drm/amd/display: Set max TTU on
DPG enable"), "hubp.h" was added which caused the duplicate include.
To be on the safe side, remove the later duplicate include.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
As hardware team suggested that we need to add a max dsc bw overhead
into existing stream bandwidth when DSC is used.
The formula as below:
max_dsc_bw_overhead =
v_addressable * slice_count * 256 bit * pixel clock / v_total / h_total
effective stream bandwidth = pixel clock * bpp
stream bandwidth = effective stream bandwidth + dsc stream overhead
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver program dpp clock calculate by pipe split config but hw config is single pipe.
[How]
Skip programming clock when allow seamless boot.
After porgramming pipe config, seamless boot flag will be clear.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change only fix dpp clock switch to lower case.
New solution later can fix both case, which is "dc: skip
program clock when allow seamless boot"
[How]
This reverts commit "dc: wait vblank when stream enabled
and update dpp clock"
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some MST devices uses different method to enable mst
specific stream features.
[How]
Add dm_helpers_mst_enable_stream features. This can be
modified later when we are ready to implement those features.
Signed-off-by: Bing Guo <bing.guo@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why?]
When a monitor does not set both QS and QY bits, DC does not
set Q0, Q1, QY0 and QY1 bits in AVI infoframe. Setting RGB bits
should be separate from setting YCC bits.
[How?]
Separate logic for setting RGB and YCC quantization range bits
in the AVI infoframe.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
While Link Training is being performed,
and the LTTPRs are in Non-LTTPR or LTTPR Transparent mode,
any DPCD registers besides those used for Link Training are not to be
accessed.
The spec defines the link training registers as DP_TRAINING_PATTERN_SET
(102h) to DP_TRAINING_LANE3_SET (106h), and DP_LANE0_1_STATUS (202h)
to DP_ADJUST_REQUEST_LANE2_3 (207h).
[HOW]
Move the current write to DPCD Address DP_LINK_TRAINING_PATTERN_SET out
of its conditional block.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We should skip programming manual trigger on non-primary planes when MPO is
enabled.
[HOW]
Implement an explicit mechanism for skipping manual trigger programming
for planes that shouldn't cause the frame to end.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previous change had been reverted since it caused hang.
Remake change to avoid defect.
[Why]
1. Driver use umachannelnumber to calculate watermarks for stutter.
In asymmetric memory config, the actual bandwidth is less than
dual-channel. The bandwidth should be the same as single-channel.
2. We found single rank dimm need additional delay time for stutter.
[How]
Get information from each DIMM. Treat memory config as a single-channel
for asymmetric memory in bandwidth calculating.
Add additional delay time for single rank dimm.
Fixes: b8720ed0b8 ("drm/amd/display: System black screen hangs on driver load")
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
We want to immediately fail seamless boot validation if DSC is active,
as VBIOS currently does not support DSC timings. Add a check for
the relevant flag in dc_validate_seamless_boot_timing.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC version 3.2.131 brings improvements in multiple areas.
In summary, we highlight:
-Enhancement for multiple eDP BL control.
-Add debug flag to enable eDP ILR by default and debugfs to repress HPD/HPR_RX IRQ.
-Fixes for DSC enable sequence,Force vsync flip,hang when psr is enabled etc.
-Firmware releases:
0.0.60
0.0.61
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SKIP_CRTC_DISABLE bit should be applicable to all dcn asics
not only Raven.
[How]
Replace check for Raven only with check for all DCNs.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When boot into OS, seamless boot device won't blank stream.
Driver update dpp clock when scanline position in vactive will show
garbage on screen.
[How]
Wait for vblank for seamless boot edp display when driver update dpp clock.
The apply seamless boot flag will be clear when OS call SetVisibility on.
Therefore we only wait for vblank once after boot into OS.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Removing unused DSC flag which is incorrect and is not used.
We are only using stream->timing.flags.DSC for DSC's current
state. Stream state as an input parameter and should not contain
any past status flags.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow observed when disabling PIP overlay in-game when
vsync is disabled, due to OTC master lock not working with
game pipe which is immediate flip.
[How]
When performing a full update, override flip_immediate value
to false for all planes, so that flip occurs on vsync.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VBIOS currently sets the max link rate found in eDP 1.4 SUPPORTED_LINK_RATES table
If eDP fastboot optimizations are enabled, the link rate remains at max after init
[How]
Determine optimal link rate during boot, disable seamless boot
and eDP fastboot optimizations if link rate optimization is required
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC version 3.2.130 brings improvements in multiple areas.
In summary, we highlight:
- Firmware release 0.0.59
- Fixes on display experiences for 4k TVs, register mask missing, etc.
- Enhancements on MST, code cleaning and debug messages.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Pipe input DSC bpc has a type mismatch with maximum DSC
input bpc - align the maximum with the pipe input type,
unsigned integer.
When checking the type we shoudl also check for an
implicit value of 0 and align with what the spreadsheet
does - default to max.
Rename output_bpc to dsc_input_bpc to reflect what the
field is actually used for.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why/how]
Due to compiler optimization the values would be
passed to the division function uninitialized
causing a div by zero. Initialize the numerator
and denominator to 0 and 1 to prevent division
by zero.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
