On some vendor switches, when switch port is toggled (down /up),
then in some condition driver tries to configure virtual port,
before FW is actually in ready state to process any commands on wire.
At this time, configuring virtual port can fail. Add fix in driver
to make driver wait, for FW to be ready state before
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Through the qla target code, the qlt_send_term_exchange() routine
is used in various different places to cleanup an exchange. For the
case of IOCB request queue is full, the exchange is left unhandled/
dangling. Existing code does not have re-try logic to cleanup the
exchange. This patch add retry logic to cleanup the exchange before
letting new commands through.
For the case of FW running out of exchanges, driver need to reply
SAM_STAT_BUSY to the initiators. This patch add a pending queue
for the busy reply in case IOCB queue is unable to handle the cmd.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A chip reset can occur after driver submits command to the stack. Abort
command processing if a chip reset has occurred or in progress when you
get a follow up for a command.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For FA-WWPN capable device, ISP2031 and ISP27XX, when loop
dead is detected by a driver, restore WWPN from NVRAM.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Parse the retry delay timer field from the FCP response data and if:
- It is not zero
- The SCSI status is busy or queue full
return SCSI_MLQUEUE_TARGET_BUSY for the number of milliseconds specified
in the retry delay timer field.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Nameserver data on FC switch is not refreshed when
qla2xxx driver is unloaded. Disabling laser for
ISP2031 will force FC switch to rescan ports and
clear fdmi entries from Nameserver.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for the D-port (diagnostic port) fabric switch feature.
(Fabric Switch initiates loopback style port testing)
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for the FDMI-2 fabric switch feature.
Since FDMI-2 uses code from FDMI-1, some of the existing code
needed to be repaired to prevent fields from being overflowed.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The PCI register read checking introduced in commit fe1b806f4f
("qla2xxx: Disable adapter when we encounter a PCI disconnect") is
active during driver probe. Hold off scheduling any board removal until
the driver probe has completed. This ensures that the the board_disable
work structure is initialized and more importantly, avoids racing
qla2x00_probe_one.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Introduce mutual exclusion between the qla2xxx_remove_one PCI driver
callback and qla2x00_disable_board_on_pci_error, which is scheduled as
board_disable work by qla2x00_check_reg{32,16}_for_disconnect:
* Leave the driver-specific data attached to the underlying PCI device
intact in qla2x00_disable_board_on_pci_error, so that qla2x00_remove_one
has enough breadcrumbs to determine that any board_disable work has been
completed.
* In qla2xxx_remove_one, set a bit to prevent any subsequent
board_disable work from scheduling, then cancel and wait until pending
work has completed.
* Reuse the PCI device enable count check in qla2x00_remove_one to
determine if board_disable has occured. The original purpose of this
check was unnecessary since the driver remove function wasn't called
when the probe fails.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are various callers of qla2x00_check_reg{32,16}_for_disconnect
that may schedule board removal on PCI-disconnect. Test-and-set a
dedicated flag before scheduling board_disable so it is invoked only
once.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for T10-Dif for Target Mode to qla driver.
The driver will look for firmware attribute that support
this feature. When the feature is present, the capabilities
will be report to TCM layer.
Add CTIO CRC2 iocb to build T10-Dif commands.
Add support routines to process good & error cases.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For ISP27xx use the request/response queue index shadow registers
to avoid directly access them on the PCI bus.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If the firmware cannot find the command specified then return SUCCESS to the
error handler so as not to needlessly escalate. Also cleanup the resources for
the command since we cannot expect the original command to returned in
interrupt context.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Allow for the capture of a firmware dump but have a sysfs node
(allow_cna_fw_dump) to allow the feature to be enabled/disabled dynamically.
The default is off.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- add support for SCSI Referrals (Hannes)
- add support for T10 DIF into target core (nab + mkp)
- add support for T10 DIF emulation in FILEIO + RAMDISK backends (Sagi + nab)
- add support for T10 DIF -> bio_integrity passthrough in IBLOCK backend (nab)
- prep changes to iser-target for >= v3.15 T10 DIF support (Sagi)
- add support for qla2xxx N_Port ID Virtualization - NPIV (Saurav + Quinn)
- allow percpu_ida_alloc() to receive task state bitmask (Kent)
- fix >= v3.12 iscsi-target session reset hung task regression (nab)
- fix >= v3.13 percpu_ref se_lun->lun_ref_active race (nab)
- fix a long-standing network portal creation race (Andy)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
target: Fix percpu_ref_put race in transport_lun_remove_cmd
target/iscsi: Fix network portal creation race
target: Report bad sector in sense data for DIF errors
iscsi-target: Convert gfp_t parameter to task state bitmask
iscsi-target: Fix connection reset hang with percpu_ida_alloc
percpu_ida: Make percpu_ida_alloc + callers accept task state bitmask
iscsi-target: Pre-allocate more tags to avoid ack starvation
qla2xxx: Configure NPIV fc_vport via tcm_qla2xxx_npiv_make_lport
qla2xxx: Enhancements to enable NPIV support for QLOGIC ISPs with TCM/LIO.
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
IB/isert: pass scatterlist instead of cmd to fast_reg_mr routine
IB/isert: Move fastreg descriptor creation to a function
IB/isert: Avoid frwr notation, user fastreg
IB/isert: seperate connection protection domains and dma MRs
tcm_loop: Enable DIF/DIX modes in SCSI host LLD
target/rd: Add DIF protection into rd_execute_rw
target/rd: Add support for protection SGL setup + release
target/rd: Refactor rd_build_device_space + rd_release_device_space
target/file: Add DIF protection support to fd_execute_rw
target/file: Add DIF protection init/format support
...
If we become disconnected from the PCI bus/PCIe fabric, there can be long delays
in register reads which can cause erroneous decisions to be made and cause a
soft lockup if a lock is held too long. As a preventative measure, check for a
disconnection (register reads that return -1) and then disable the board if we
find ourselves in this condition. For now, check in our interrupt handlers and
the per adapter one second timer.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Earlier IDC-TIME-EXTEND aen was a nop and ignored by driver.
We now have to handle the aen so that other protocol drivers can use time
extension during some loopback operations.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For supported ISPS, Read asic temperature by calling the
GET PARAMS (type C) mailbox command.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
qla2x00_loopback_test() was hard setting the loopback iteration
count to 1 rather than obtaining it from the bsg request.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
