Vlans are not getting removed when drivers are unloaded. The recent storm
firmware versions had added safeguards against re-configuring an already
configured vlan. As a result, PF inner reload flows (e.g., mtu change)
might trigger an assertion.
This change is going to remove vlans (same as we do for MACs) when doing
a chip cleanup during unload.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some customer setups it was observed that shmem contains a non-zero fip
MAC for 57711 which would lead to enabling of SW FCoE.
Add a software workaround to clear the bad fip mac address if no FCoE
connections are supported.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_DEBUG_SHIRQ is enabled __free_irq() intentionally fires
a spurious interrupt. This interrupt causes a crash because
tp->dev->phydev is NULL at that time.
Fixes: 38caff5a44 ("r8169: handle all interrupt events in the hard irq handler")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we did not ensure tcp flags have a place to be stored
when using IPv6. We correct this by including IPv6 key layer when
we match tcp flags and the IPv6 key layer has not been included
already.
Fixes: 07e1671cfc ("nfp: flower: refactor shared ip header in match offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CP rings are accounted differently on the new 57500 chips. There
must be enough CP rings for the sum of RX and TX rings on the new
chips. The current logic may be over-estimating the RX and TX rings.
The output parameter max_cp should be the maximum NQs capped by
MSIX vectors available for networking in the context of 57500 chips.
The existing code which uses CMPL rings capped by the MSIX vectors
works most of the time but is not always correct.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new 57500 chips have introduced the NQ structure in addition to
the existing CP rings in all chips. We need to introduce a new
bnxt_nq_rings_in_use(). On legacy chips, the 2 functions are the
same and one will just call the other. On the new chips, they
refer to the 2 separate ring structures. The new function is now
called to determine the resource (NQ or CP rings) associated with
MSIX that are in use.
On 57500 chips, the RDMA driver does not use the CP rings so
we don't need to do the subtraction adjustment.
Fixes: 41e8d79837 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new 57500 chips use 1 NQ per MSIX vector, whereas legacy chips use
1 CP ring per MSIX vector. To better unify this, add a resv_irqs
field to struct bnxt_hw_resc. On legacy chips, we initialize resv_irqs
with resv_cp_rings. On new chips, we initialize it with the allocated
MSIX resources.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to support the 57500 devices have created this
regression. The bnxt_hwrm_queue_qportcfg() call was moved to be
called earlier before the RDMA support was determined, causing
the CoS queues configuration to be set before knowing whether RDMA
was supported or not. Fix it by moving it to the right place right
after RDMA support is determined.
Fixes: 98f04cf0f1 ("bnxt_en: Check context memory requirements from firmware.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_ppp and tx_ppp can be set between 0 and 255, so don't clamp to 1.
Fixes: 6e8814ceb7 ("net/mlx4_en: Fix mixed PFC and Global pause user control requests")
Signed-off-by: Tarick Bedeir <tarick@google.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 624ca9c33c.
This commit is completely bogus. The STACR register has two formats, old
and new, depending on the version of the IP block used. There's a pair of
device-tree properties that can be used to specify the format used:
has-inverted-stacr-oc
has-new-stacr-staopc
What this commit did was to change the bit definition used with the old
parts to match the new parts. This of course breaks the driver on all
the old ones.
Instead, the author should have set the appropriate properties in the
device-tree for the variant used on his board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.
The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.
Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE decap offload is configured when local routes prefix correspond to the
local address of one of the offloaded GRE tunnels. The matching check was
found to be too strict, such that for a flat GRE configuration, in which
the overlay and underlay traffic share the same non-default VRF, decap flow
was not offloaded.
Relax the check for decap flow offloading. A match occurs if the local
address of the tunnel matches the local route address while both share the
same VRF table.
Fixes: 4607f6d269 ("mlxsw: spectrum_router: Support IPv4 underlay decap")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should never be possible for a user to set a VNI on a FID in case one
is already set. The driver therefore returns an error, but fails to drop
the reference count taken earlier when calling
mlxsw_sp_fid_8021d_lookup().
Drop the reference when this unlikely error is hit.
Fixes: 1c30d1836a ("mlxsw: spectrum: Enable VxLAN enslavement to bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to trigger a warning in mlxsw in case a flood entry which
mlxsw is not aware of is deleted from the VxLAN device. This is because
mlxsw expects to find a singly linked list where the flood entry is
present in.
Fix by removing these warnings for now.
Will re-add them in the next release after we teach mlxsw to ask for a
dump of FDB entries from the VxLAN device, once it is enslaved to a
bridge mlxsw cares about.
Fixes: 6e6030bd54 ("mlxsw: spectrum_nve: Implement common NVE core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .validate phylink callback should empty the supported bitmap when
the interface mode is invalid.
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_phylink_validate() relies on the interface field of
phylink_link_state to determine valid link modes. However, when called
from phylink_sfp_module_insert() this field in not initialized. The
default switch case then excludes 10G link modes. This allows 10G SFP
modules that are detected correctly to be configured at max rate of
2.5G.
Catch the uninitialized PHY mode case, and allow 10G rates.
Fixes: d97c9f4ab0 ("net: mvpp2: 1000baseX support")
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
After getting a reference to the platform device's of_node the probe
function ends up calling of_find_matching_node() using the node as an
argument. The function takes care of decreasing the refcount on it. We
are then incorrectly decreasing the refcount on that node again.
This patch removes the unwarranted call to of_node_put().
Fixes: 414fd46e77 ("fsl/fman: Add FMan support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
MLX4_EN depends on NETDEVICES, ETHERNET and INET Kconfigs.
Make sure they are listed in MLX4_EN Kconfig dependencies.
This fixes the following build break:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: ‘struct iphdr’ declared inside parameter list [enabled by default]
struct iphdr *iph)
^
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/ethernet/mellanox/mlx4/en_rx.c: In function ‘get_fixed_ipv4_csum’:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:586:20: error: dereferencing pointer to incomplete type
_u8 ipproto = iph->protocol;
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC driver minimal MTU size shall be set to ETH_MIN_MTU, as defined in
the RFC791 and in the network stack. Remove old mlx4_en only define for
it, which was set to wrong value.
Fixes: b80f71f581 ("ethernet/mellanox: use core min/max MTU checking")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5681e20b5 ("net/ibmnvic: Fix deadlock problem
in reset") made the change to hold the RTNL lock during
driver reset but still calls netdev_notify_peers, which
results in a deadlock. Instead, use call_netdevice_notifiers,
which is functionally the same except that it does not
take the RTNL lock again.
Fixes: a5681e20b5 ("net/ibmnvic: Fix deadlock problem in reset")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function lio_vf_rep_packet_sent_callback releases the occupation of
sc via octeon_free_soft_command. sc should not be used after that.
Unfortunately, sc->iq_no is read. To fix this, the patch stores sc->iq_no
into a local variable before releasing sc and then uses the local variable
instead of sc->iq_no.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP header is not necessarily located right after struct ethhdr,
there could be multiple 802.1Q headers in between, this is why
we call __vlan_get_protocol().
Fixes: fe1dc06999 ("net/mlx5e: don't set CHECKSUM_COMPLETE on SCTP packets")
Cc: Alaa Hleihel <alaa@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For flow offload adds, if the rhash insert code fails, the flow will still
have been offloaded but the reference to it in the driver freed.
Re-order the offload setup calls to ensure that a flow will only be written
to FW if a kernel reference is held and stored in the rhashtable. Remove
this hashtable entry if the offload fails.
Fixes: c01d0efa51 ("nfp: flower: use rhashtable for flow caching")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling nfp_compile_flow_metadata both assigns a stats context and
increments a ref counter on (or allocates) a mask id table entry. These
are released by the nfp_modify_flow_metadata call on flow deletion,
however, if a flow add fails after metadata is set then the flow entry
will be deleted but the metadata assignments leaked.
Add an error path to the flow add offload function to ensure allocated
metadata is released in the event of an offload fail.
Fixes: 81f3ddf254 ("nfp: add control message passing capabilities to flower offloads")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last set of csum offload fixes had a leak:
Checksum enabled status bits from rx descriptor were incorrectly
interpreted. Consequently all the other valid logic worked on zero bits.
That caused rx checksum offloads never to trigger.
Tested by dumping rx descriptors and validating resulting csum_level.
Reported-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Fixes: ad703c2b91 ("net: aquantia: invalid checksumm offload implementation")
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in the oct_stats_strings array, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting up and tearing down debugfs is current unbalanced, as seen by
this error during resume from suspend:
[ 752.134067] dwc-eth-dwmac 2490000.ethernet eth0: ERROR failed to create debugfs directory
[ 752.134347] dwc-eth-dwmac 2490000.ethernet eth0: stmmac_hw_setup: failed debugFS registration
The imbalance happens because the driver creates the debugfs hierarchy
when the device is opened and tears it down when the device is closed.
There's little gain in that, and it could be argued that it is even
surprising because it's not usually done for other devices. Fix the
imbalance by moving the debugfs creation and teardown to the driver's
->probe() and ->remove() implementations instead.
Note that the ring descriptors cannot be read while the interface is
down, so make sure to return an empty file when the descriptors_status
debugfs file is read.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing MODULE_AUTHOR of ave driver and an entry to MAINTAINERS.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 26a4676faa ("arm64: mm: define NET_IP_ALIGN to 0"),
AVE controller affects this modification because the controller forces
to ignore lower 2bits of buffer start address, and make 2-byte headroom,
that is, data reception starts from (buffer + 2).
This patch defines AVE_FRAME_HEADROOM macro as hardware-specific value,
and replaces NET_IP_ALIGN with it.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To improve performance, this increases Rx descriptor to 256, Tx descriptor
to 64, and adjusts NAPI weight to NAPI_POLL_WEIGHT.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2018-11-28
This series contains fixes to igb, ixgbe and i40e.
Yunjian Wang from Huawei resolves a variable that could potentially be
NULL before it is used.
Lihong fixes an i40e issue which goes back to 4.17 kernels, where
deleting any of the MAC filters was causing the incorrect syncing for
the PF.
Josh Elsasser caught that there were missing enum values in the link
capabilities for x550 devices, which was preventing link for 1000BaseLX
SFP modules.
Jan fixes the function header comments for XSK methods.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The net device ndev is freed via free_netdev when failing to register
the device. The control flow then jumps to the error handling code
block. ndev is used and freed again. Resulting in a use-after-free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One method, xsk_umem_setup, had an incorrect kernel doc
description, which has been corrected.
Also fixes small typos found in the comments.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the two 1000BaseLX enum values to the X550's check for 1Gbps modules,
allowing the core driver code to establish a link over this SFP type.
This is done by the out-of-tree driver but the fix wasn't in mainline.
Fixes: e23f333678 ("ixgbe: Fix 1G and 10G link stability for X550EM_x SFP+”)
Fixes: 6a14ee0cfb ("ixgbe: Add X550 support function pointers")
Signed-off-by: Josh Elsasser <jelsasser@appneta.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In __i40e_del_filter function, the flag __I40E_MACVLAN_SYNC_PENDING for
the PF state is wrongly set for the VSI. Deleting any of the MAC filters
has caused the incorrect syncing for the PF. Fix it by setting this state
flag to the intended PF.
CC: stable <stable@vger.kernel.org>
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the variable 'phy_word' may be used uninitialized.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This driver was designed to work with both LAN7430 and LAN7431.
The only difference between the two is the LAN7431 has support
for external phy.
This change adds LAN7431 to the list of recognized devices
supported by this driver.
Updates for v2:
changed 'fixes' tag to match defined format
fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan743x driver, when under heavy traffic load, has been noticed
to sometimes hang, or cause a kernel panic.
Debugging reveals that the TX napi poll routine was returning
the wrong value, 'weight'. Most other drivers return 0.
And call napi_complete, instead of napi_complete_done.
Additionally when creating the tx napi poll routine.
Changed netif_napi_add, to netif_tx_napi_add.
Updates for v3:
changed 'fixes' tag to match defined format
Updates for v2:
use napi_complete, instead of napi_complete_done in
lan743x_tx_napi_poll
use netif_tx_napi_add, instead of netif_napi_add for
registration of tx napi poll routine
fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The text in array velocity_gstrings contains a spelling mistake,
rename rx_frame_alignement_errors to rx_frame_alignment_errors.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The text in array s_igu_fifo_error_strs contains a spelling mistake,
fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX stats should be started with the tx_stats_syncp,
there seems to be a copy/paste error in the driver.
Signed-off-by: Andreas Fiedler <andreas.fiedler@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
This place doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During device reset, queue memory is not being updated to accommodate
changes in ring buffer sizes supported by backing hardware. Track
any differences in ring buffer sizes following the reset and update
queue memory when possible.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong index is used when cleaning up RX buffer objects during release
of RX queues. Update to use the correct index counter.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set xdp_prog pointer to NULL if bpf_prog_add fails since that routine
reports the error code instead of NULL in case of failure and xdp_prog
pointer value is used in the driver to verify if XDP is currently
enabled.
Moreover report the error code to userspace if nicvf_xdp_setup fails
Fixes: 05c773f52b ("net: thunderx: Add basic XDP support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
