When the NMI IPI lock is contended, spin at low SMT priority, using
loads only, and with interrupts enabled (where possible). This
improves behaviour under high contention (e.g., a system crash when
a number of CPUs are trying to enter the debugger).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 05a4a95279 ("kernel/watchdog: split up config options"),
CONFIG_LOCKUP_DETECTOR was split into two separate config options,
CONFIG_HARDLOCKUP_DETECTOR and CONFIG_SOFTLOCKUP_DETECTOR.
Our defconfigs still have CONFIG_LOCKUP_DETECTOR=y, but that is no longer
user selectable, and we don't mention the new options, so we end up with
none of them enabled.
So update the defconfigs to turn on the new SOFT and HARD options, the
end result being the same as what we had previously.
Fixes: 05a4a95279 ("kernel/watchdog: split up config options")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, we use the opal call opal_slw_set_reg() to inform the
Sleep-Winkle Engine (SLW) to restore the contents of some of the
Hypervisor state on wakeup from deep idle states that lose full
hypervisor context (characterized by the flag
OPAL_PM_LOSE_FULL_CONTEXT).
However, the current code has a bug in that if opal_slw_set_reg()
fails, we don't disable the use of these deep states (winkle on
POWER8, stop4 onwards on POWER9).
This patch fixes this bug by ensuring that if programing the
sleep-winkle engine to restore the hypervisor states in
pnv_save_sprs_for_deep_states() fails, then we exclude such states by
clearing the OPAL_PM_LOSE_FULL_CONTEXT flag from
supported_cpuidle_states. As a result POWER8 will be prevented from
using winkle for CPU-Hotplug, and POWER9 will put the offlined CPUs to
the default stop state when available.
Further, we ensure in the initialization of the cpuidle-powernv driver
to only include those states whose flags are present in
supported_cpuidle_states, thereby skipping OPAL_PM_LOSE_FULL_CONTEXT
states when they have been disabled due to stop-api failure.
Fixes: 1e1601b38e ("powerpc/powernv/idle: Restore SPRs for deep idle
states via stop API.")
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the decrementer wraps again and de-asserts the decrementer
exception while hard-disabled, __check_irq_replay() has a test to
notice the wrap when interrupts are re-enabled.
The decrementer check must be done when clearing the PACA_IRQ_HARD_DIS
flag, not when the PACA_IRQ_DEC flag is tested. Previously this worked
because the decrementer interrupt was always the first one checked
after clearing the hard disable flag, but HMI check was moved ahead of
that, which introduced this bug.
This can cause a missed decrementer interrupt if we soft-disable
interrupts then take an HMI which is recorded in irq_happened, then
hard-disable interrupts for > 4s to wrap the decrementer.
Fixes: e0e0d6b739 ("powerpc/64: Replay hypervisor maintenance interrupt first")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD2 PMU can stop after a state-loss idle in some conditions.
A solution is to set then clear MMCRA[60] after wake from state-loss
idle. MMCRA[60] is a non-architected bit, see the user manual for
details.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
of_irq_to_resource() has recently been fixed to return negative error #'s
along with 0 in case of failure, however the Freescale MPC832x RDB board
code still only regards 0 as a failure indication -- fix it up.
Fixes: 7a4228bbff ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The watchdog soft-NMI exception stack setup loads a stack pointer
twice, which is an obvious error. It ends up using the system reset
interrupt (true-NMI) stack, which is also a bug because the watchdog
could be preempted by a system reset interrupt that overwrites the
NMI stack.
Change the soft-NMI to use the "emergency stack". The current kernel
stack is not used, because of the longer-term goal to prevent
asynchronous stack access using soft-disable.
Fixes: 2104180a53 ("powerpc/64s: implement arch-specific hardlockup watchdog")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZapWhAAoJEHm+PkMAQRiGKb0IAJM6b7SbWaw69Og7+qiFB+zZ
xp29iXqbE9fPISC6a5BRQV1ONjeDM6opGixGHqGC8Hla6k2IYz25VDNoF8wd0MXN
cz/Ih20vd3C5afxXGe5cTT8lsPAlV0mWXxForlu6j8jPeL62FPfq6RhEkw7AcrYL
yfYy3k3qSdOrrvBdII0WAAUi46UfIs+we9BQgbsMbkHOiqV2K0MOrzKE84Xbgepq
RAy2xg6P4b4+hTx8xTrYc1MXwpnqjRc0oJ08gdmiwW3AOOU7LxYFn7zDkLPWi9Rr
g4x6r4YhBTGxT4wNvovLIiqd9QFs//dMCuPWYwEtTICG48umIqqq24beQ0mvCdg=
=08Ic
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rc1' into fixes
The fixes branch is based off a random pre-rc1 commit, because we had
some fixes that needed to go in before rc1 was released.
However we now need to fix some code that went in after that point, but
before rc1, so merge rc1 to get that code into fixes so we can fix it!
Commit 8e3f1b1d82 ("powerpc/powernv/pci: Enable 64-bit devices to access
>4GB DMA space") introduced the ability for PCI device drivers to request a
DMA mask between 64 and 32 bits and actually get a mask greater than
32-bits. However currently if certain machine configuration dependent
conditions are not meet the code silently falls back to a 32-bit mask.
This makes it hard for device drivers to detect which mask they actually
got. Instead we should return an error when the request could not be
fulfilled which allows drivers to either fallback or implement other
workarounds as documented in DMA-API-HOWTO.txt.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Historically the boot wrapper was always built 32-bit big endian, even
for 64-bit kernels. That was because old firmwares didn't necessarily
support booting a 64-bit image. Because of that arch/powerpc/boot/Makefile
uses CROSS32CC for compilation.
However when we added 64-bit little endian support, we also added
support for building the boot wrapper 64-bit. However we kept using
CROSS32CC, because in most cases it is just CC and everything works.
However if the user doesn't specify CROSS32_COMPILE (which no one ever
does AFAIK), and CC is *not* biarch (32/64-bit capable), then CROSS32CC
becomes just "gcc". On native systems that is probably OK, but if we're
cross building it definitely isn't, leading to eg:
gcc ... -m64 -mlittle-endian -mabi=elfv2 ... arch/powerpc/boot/cpm-serial.c
gcc: error: unrecognized argument in option ‘-mabi=elfv2’
gcc: error: unrecognized command line option ‘-mlittle-endian’
make: *** [zImage] Error 2
To fix it, stop using CROSS32CC, because we may or may not be building
32-bit. Instead setup a BOOTCC, which defaults to CC, and only use
CROSS32_COMPILE if it's set and we're building for 32-bit.
Fixes: 147c05168f ("powerpc/boot: Add support for 64bit little endian wrapper")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
In smp_cpus_done() we need to call smp_ops->setup_cpu() for the boot
CPU, which means it has to run *on* the boot CPU.
In the past we ensured it ran on the boot CPU by changing the CPU
affinity mask of current directly. That was removed in commit
6d11b87d55 ("powerpc/smp: Replace open coded task affinity logic"),
and replaced with a work queue call.
Unfortunately using a work queue leads to a lockdep warning, now that
the CPU hotplug lock is a regular semaphore:
======================================================
WARNING: possible circular locking dependency detected
...
kworker/0:1/971 is trying to acquire lock:
(cpu_hotplug_lock.rw_sem){++++++}, at: [<c000000000100974>] apply_workqueue_attrs+0x34/0xa0
but task is already holding lock:
((&wfc.work)){+.+.+.}, at: [<c0000000000fdb2c>] process_one_work+0x25c/0x800
...
CPU0 CPU1
---- ----
lock((&wfc.work));
lock(cpu_hotplug_lock.rw_sem);
lock((&wfc.work));
lock(cpu_hotplug_lock.rw_sem);
Although the deadlock can't happen in practice, because
smp_cpus_done() only runs in early boot before CPU hotplug is allowed,
lockdep can't tell that.
Luckily in commit 8fb12156b8 ("init: Pin init task to the boot CPU,
initially") tglx changed the generic code to pin init to the boot CPU
to begin with. The unpinning of init from the boot CPU happens in
sched_init_smp(), which is called after smp_cpus_done().
So smp_cpus_done() is always called on the boot CPU, which means we
don't need the work queue call at all - and the lockdep warning goes
away.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Currently flush_tmregs_to_thread() does not save the TM SPRs (TFHAR,
TFIAR, TEXASR) to the thread struct, unless the process is currently
inside a suspended transaction.
If the process is core dumping, and the TM SPRs have changed since the
last time the process was context switched, then we will save stale
values of the TM SPRs to the core dump.
Fix it by saving the live register state to the thread struct in that
case.
Fixes: 08e1c01d6a ("powerpc/ptrace: Enable support for TM SPR state")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Radix MMU translation tree as defined in ISA v3.0 contains two
different types of entry, directories and leaves. Leaves are
identified by _PAGE_PTE being set.
The formats of the two entries are different, with the directory
entries containing no spare bits for use by software. In particular
the bit we use for _PAGE_DEVMAP is not reserved for software, and is
part of the NLB (Next Level Base) field, essentially the address of
the next level in the tree.
Note that the Linux pte_t is not == _PAGE_PTE. A huge page pmd
entry (or devmap!) is also a leaf and so has _PAGE_PTE set, even
though we use a pmd_t for it in Linux.
The fix is to ensure that the pmd/pte_devmap() confirm they are
looking at a leaf entry (_PAGE_PTE) as well as checking _PAGE_DEVMAP.
Fixes: ebd3119793 ("powerpc/mm: Add devmap support for ppc64")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Tested-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Add a comment in the code and flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: dad6f37c26 ("powerpc: subpage_protect: Increase the array size to take care of 64TB")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Tested-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit efe0160cfd ("powerpc/64: Linker on-demand sfpr functions
for modules"), we added an ld version check early in the powerpc
top-level Makefile.
Because the Makefile runs before the kernel config is setup, the
checks for CONFIG_CPU_LITTLE_ENDIAN etc. all take the default case. So
we end up configuring ld for 32-bit big endian.
That would be OK, except that for historical (or perhaps no) reason,
we use 'override LD' to add the endian flags to the LD variable
itself, rather than the normal approach of adding them to LDFLAGS.
The end result is that when we check the ld version we run it as:
$(CROSS_COMPILE)ld -EB -m elf32ppc --version
This often works, unless you are using a 64-bit only and/or little
endian only, toolchain. In which case you see something like:
$ make defconfig
powerpc64le-linux-ld: unrecognised emulation mode: elf32ppc
Supported emulations: elf64lppc elf32lppc elf32lppclinux elf32lppcsim
/bin/sh: 1: [: -ge: unexpected operator
The proper fix is to stop using 'override LD', but that will require a
fair bit of testing. Instead we can fix it for now just by reordering
the Makefile to do the version check earlier.
Fixes: efe0160cfd ("powerpc/64: Linker on-demand sfpr functions for modules")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As for commit 68baf692c4 ("powerpc/pseries: Fix of_node_put()
underflow during DLPAR remove"), the call to of_node_put() must be
removed from pSeries_reconfig_remove_node().
dlpar_detach_node() and pSeries_reconfig_remove_node() both call
of_detach_node(), and thus the node should not be released in both
cases.
Fixes: 0829f6d1f6 ("of: device_node kobject lifecycle fixes")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's a somewhat architectural issue with Radix MMU and KVM.
When coming out of a guest with AIL (Alternate Interrupt Location, ie,
MMU enabled), we start executing hypervisor code with the PID register
still containing whatever the guest has been using.
The problem is that the CPU can (and will) then start prefetching or
speculatively load from whatever host context has that same PID (if
any), thus bringing translations for that context into the TLB, which
Linux doesn't know about.
This can cause stale translations and subsequent crashes.
Fixing this in a way that is neither racy nor a huge performance
impact is difficult. We could just make the host invalidations always
use broadcast forms but that would hurt single threaded programs for
example.
We chose to fix it instead by partitioning the PID space between guest
and host. This is possible because today Linux only use 19 out of the
20 bits of PID space, so existing guests will work if we make the host
use the top half of the 20 bits space.
We additionally add support for a property to indicate to Linux the
size of the PID register which will be useful if we eventually have
processors with a larger PID space available.
There is still an issue with malicious guests purposefully setting the
PID register to a value in the hosts PID range. Hopefully future HW
can prevent that, but in the meantime, we handle it with a pair of
kludges:
- On the way out of a guest, before we clear the current VCPU in the
PACA, we check the PID and if it's outside of the permitted range
we flush the TLB for that PID.
- When context switching, if the mm is "new" on that CPU (the
corresponding bit was set for the first time in the mm cpumask), we
check if any sibling thread is in KVM (has a non-NULL VCPU pointer
in the PACA). If that is the case, we also flush the PID for that
CPU (core).
This second part is needed to handle the case where a process is
migrated (or starts a new pthread) on a sibling thread of the CPU
coming out of KVM, as there's a window where stale translations can
exist before we detect it and flush them out.
A future optimization could be added by keeping track of whether the
PID has ever been used and avoid doing that for completely fresh PIDs.
We could similarily mark PIDs that have been the subject of a global
invalidation as "fresh". But for now this will do.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Rework the asm to build with CONFIG_PPC_RADIX_MMU=n, drop
unneeded include of kvm_book3s_asm.h]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently even with STRICT_KERNEL_RWX we leave the __init text marked
executable after init, which is bad.
Add a hook to mark it NX (no-execute) before we free it, and implement
it for radix and hash.
Note that we use __init_end as the end address, not _einittext,
because overlaps_kernel_text() uses __init_end, because there are
additional executable sections other than .init.text between
__init_begin and __init_end.
Tested on radix and hash with:
0:mon> p $__init_begin
*** 400 exception occurred
Fixes: 1e0fc9d1eb ("powerpc/Kconfig: Enable STRICT_KERNEL_RWX for some configs")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the core logic into a helper, so we can use it for changing other
permissions.
We also change the logic to align start down, and end up. This means
calling the function with a range will expand that range to be at
least 1 mmu_linear_psize page in size. We need that so we can use it
on __init_begin ... __init_end which is not a full page in size.
This should always work for _stext/__init_begin, because we align
__init_begin to _stext + 16M in the linker script.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the core logic into a helper, so we can use it for changing permissions
other than _PAGE_WRITE.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A previous optimisation incorrectly assumed the PAPR hcall does
not use r12, and clobbers it upon entry. In fact it is used as
an input. This can result in KVM guests crashing (observed with
PR KVM).
Instead of using r12 to save r13, tihs patch saves r13 in ctr.
This is more costly, but not as slow as using the SPRG.
Fixes: acd7d8cef0 ("powerpc/64s: Optimize hypercall/syscall entry")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD2 can see spurious PMU interrupts after state-loss idle in
some conditions.
A solution is to save and reload MMCR0 over state-loss idle.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 1c0eaf0f56 ("powerpc/powernv: Tell OPAL about our MMU mode
on POWER9"), we added additional flags to the OPAL call to configure
CPUs at boot.
These flags only work on Power9 firmwares, and worse can cause boot
failures on Power8 machines, so we check for CPU_FTR_ARCH_300 (aka POWER9)
before adding the extra flags.
Unfortunately we forgot that opal_configure_cores() is called before
the CPU feature checks are dynamically patched, meaning the check
always returns true.
We definitely need to do something to make the CPU feature checks less
prone to bugs like this, but for now the minimal fix is to use
early_cpu_has_feature().
Reported-and-tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Fixes: 1c0eaf0f56 ("powerpc/powernv: Tell OPAL about our MMU mode on POWER9")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull ->s_options removal from Al Viro:
"Preparations for fsmount/fsopen stuff (coming next cycle). Everything
gets moved to explicit ->show_options(), killing ->s_options off +
some cosmetic bits around fs/namespace.c and friends. Basically, the
stuff needed to work with fsmount series with minimum of conflicts
with other work.
It's not strictly required for this merge window, but it would reduce
the PITA during the coming cycle, so it would be nice to have those
bits and pieces out of the way"
* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
isofs: Fix isofs_show_options()
VFS: Kill off s_options and helpers
orangefs: Implement show_options
9p: Implement show_options
isofs: Implement show_options
afs: Implement show_options
affs: Implement show_options
befs: Implement show_options
spufs: Implement show_options
bpf: Implement show_options
ramfs: Implement show_options
pstore: Implement show_options
omfs: Implement show_options
hugetlbfs: Implement show_options
VFS: Don't use save/replace_mount_options if not using generic_show_options
VFS: Provide empty name qstr
VFS: Make get_filesystem() return the affected filesystem
VFS: Clean up whitespace in fs/namespace.c and fs/super.c
Provide a function to create a NUL-terminated string from unterminated data
Pull uacess-unaligned removal from Al Viro:
"That stuff had just one user, and an exotic one, at that - binfmt_flat
on arm and m68k"
* 'work.uaccess-unaligned' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
kill {__,}{get,put}_user_unaligned()
binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail
Nothing that really stands out, just a bunch of fixes that have come in in the
last couple of weeks.
None of these are actually fixes for code that is new in 4.13. It's roughly half
older bugs, with fixes going to stable, and half fixes/updates for Power9.
Thanks to:
Aneesh Kumar K.V, Anton Blanchard, Balbir Singh, Benjamin Herrenschmidt,
Madhavan Srinivasan, Michael Neuling, Nicholas Piggin, Oliver O'Halloran.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6eIT
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Nothing that really stands out, just a bunch of fixes that have come
in in the last couple of weeks.
None of these are actually fixes for code that is new in 4.13. It's
roughly half older bugs, with fixes going to stable, and half
fixes/updates for Power9.
Thanks to: Aneesh Kumar K.V, Anton Blanchard, Balbir Singh, Benjamin
Herrenschmidt, Madhavan Srinivasan, Michael Neuling, Nicholas Piggin,
Oliver O'Halloran"
* tag 'powerpc-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64: Fix atomic64_inc_not_zero() to return an int
powerpc: Fix emulation of mfocrf in emulate_step()
powerpc: Fix emulation of mcrf in emulate_step()
powerpc/perf: Add POWER9 alternate PM_RUN_CYC and PM_RUN_INST_CMPL events
powerpc/perf: Fix SDAR_MODE value for continous sampling on Power9
powerpc/asm: Mark cr0 as clobbered in mftb()
powerpc/powernv: Fix local TLB flush for boot and MCE on POWER9
powerpc/mm/radix: Synchronize updates to the process table
powerpc/mm/radix: Properly clear process table entry
powerpc/powernv: Tell OPAL about our MMU mode on POWER9
powerpc/kexec: Fix radix to hash kexec due to IAMR/AMOR
__GFP_REPEAT was designed to allow retry-but-eventually-fail semantic to
the page allocator. This has been true but only for allocations
requests larger than PAGE_ALLOC_COSTLY_ORDER. It has been always
ignored for smaller sizes. This is a bit unfortunate because there is
no way to express the same semantic for those requests and they are
considered too important to fail so they might end up looping in the
page allocator for ever, similarly to GFP_NOFAIL requests.
Now that the whole tree has been cleaned up and accidental or misled
usage of __GFP_REPEAT flag has been removed for !costly requests we can
give the original flag a better name and more importantly a more useful
semantic. Let's rename it to __GFP_RETRY_MAYFAIL which tells the user
that the allocator would try really hard but there is no promise of a
success. This will work independent of the order and overrides the
default allocator behavior. Page allocator users have several levels of
guarantee vs. cost options (take GFP_KERNEL as an example)
- GFP_KERNEL & ~__GFP_RECLAIM - optimistic allocation without _any_
attempt to free memory at all. The most light weight mode which even
doesn't kick the background reclaim. Should be used carefully because
it might deplete the memory and the next user might hit the more
aggressive reclaim
- GFP_KERNEL & ~__GFP_DIRECT_RECLAIM (or GFP_NOWAIT)- optimistic
allocation without any attempt to free memory from the current
context but can wake kswapd to reclaim memory if the zone is below
the low watermark. Can be used from either atomic contexts or when
the request is a performance optimization and there is another
fallback for a slow path.
- (GFP_KERNEL|__GFP_HIGH) & ~__GFP_DIRECT_RECLAIM (aka GFP_ATOMIC) -
non sleeping allocation with an expensive fallback so it can access
some portion of memory reserves. Usually used from interrupt/bh
context with an expensive slow path fallback.
- GFP_KERNEL - both background and direct reclaim are allowed and the
_default_ page allocator behavior is used. That means that !costly
allocation requests are basically nofail but there is no guarantee of
that behavior so failures have to be checked properly by callers
(e.g. OOM killer victim is allowed to fail currently).
- GFP_KERNEL | __GFP_NORETRY - overrides the default allocator behavior
and all allocation requests fail early rather than cause disruptive
reclaim (one round of reclaim in this implementation). The OOM killer
is not invoked.
- GFP_KERNEL | __GFP_RETRY_MAYFAIL - overrides the default allocator
behavior and all allocation requests try really hard. The request
will fail if the reclaim cannot make any progress. The OOM killer
won't be triggered.
- GFP_KERNEL | __GFP_NOFAIL - overrides the default allocator behavior
and all allocation requests will loop endlessly until they succeed.
This might be really dangerous especially for larger orders.
Existing users of __GFP_REPEAT are changed to __GFP_RETRY_MAYFAIL
because they already had their semantic. No new users are added.
__alloc_pages_slowpath is changed to bail out for __GFP_RETRY_MAYFAIL if
there is no progress and we have already passed the OOM point.
This means that all the reclaim opportunities have been exhausted except
the most disruptive one (the OOM killer) and a user defined fallback
behavior is more sensible than keep retrying in the page allocator.
[akpm@linux-foundation.org: fix arch/sparc/kernel/mdesc.c]
[mhocko@suse.com: semantic fix]
Link: http://lkml.kernel.org/r/20170626123847.GM11534@dhcp22.suse.cz
[mhocko@kernel.org: address other thing spotted by Vlastimil]
Link: http://lkml.kernel.org/r/20170626124233.GN11534@dhcp22.suse.cz
Link: http://lkml.kernel.org/r/20170623085345.11304-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Alex Belits <alex.belits@cavium.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: NeilBrown <neilb@suse.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When RLIMIT_STACK is, for example, 256MB, the current code results in a
gap between the top of the task and mmap_base of 256MB, failing to take
into account the amount by which the stack address was randomized. In
other words, the stack gets less than RLIMIT_STACK space.
Ensure that the gap between the stack and mmap_base always takes stack
randomization and the stack guard gap into account.
Inspired by Daniel Micay's linux-hardened tree.
Link: http://lkml.kernel.org/r/20170622200033.25714-4-riel@redhat.com
Signed-off-by: Rik van Riel <riel@redhat.com>
Reported-by: Florian Weimer <fweimer@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Daniel Micay <danielmicay@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for compiling with a rough equivalent to the glibc
_FORTIFY_SOURCE=1 feature, providing compile-time and runtime buffer
overflow checks for string.h functions when the compiler determines the
size of the source or destination buffer at compile-time. Unlike glibc,
it covers buffer reads in addition to writes.
GNU C __builtin_*_chk intrinsics are avoided because they would force a
much more complex implementation. They aren't designed to detect read
overflows and offer no real benefit when using an implementation based
on inline checks. Inline checks don't add up to much code size and
allow full use of the regular string intrinsics while avoiding the need
for a bunch of _chk functions and per-arch assembly to avoid wrapper
overhead.
This detects various overflows at compile-time in various drivers and
some non-x86 core kernel code. There will likely be issues caught in
regular use at runtime too.
Future improvements left out of initial implementation for simplicity,
as it's all quite optional and can be done incrementally:
* Some of the fortified string functions (strncpy, strcat), don't yet
place a limit on reads from the source based on __builtin_object_size of
the source buffer.
* Extending coverage to more string functions like strlcat.
* It should be possible to optionally use __builtin_object_size(x, 1) for
some functions (C strings) to detect intra-object overflows (like
glibc's _FORTIFY_SOURCE=2), but for now this takes the conservative
approach to avoid likely compatibility issues.
* The compile-time checks should be made available via a separate config
option which can be enabled by default (or always enabled) once enough
time has passed to get the issues it catches fixed.
Kees said:
"This is great to have. While it was out-of-tree code, it would have
blocked at least CVE-2016-3858 from being exploitable (improper size
argument to strlcpy()). I've sent a number of fixes for
out-of-bounds-reads that this detected upstream already"
[arnd@arndb.de: x86: fix fortified memcpy]
Link: http://lkml.kernel.org/r/20170627150047.660360-1-arnd@arndb.de
[keescook@chromium.org: avoid panic() in favor of BUG()]
Link: http://lkml.kernel.org/r/20170626235122.GA25261@beast
[keescook@chromium.org: move from -mm, add ARCH_HAS_FORTIFY_SOURCE, tweak Kconfig help]
Link: http://lkml.kernel.org/r/20170526095404.20439-1-danielmicay@gmail.com
Link: http://lkml.kernel.org/r/1497903987-21002-8-git-send-email-keescook@chromium.org
Signed-off-by: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Testing the fortified string functions[1] would cause a kernel panic on
boot in test_feature_fixups() due to a buffer overflow in memcmp.
This boils down to things like this:
extern unsigned int ftr_fixup_test1;
extern unsigned int ftr_fixup_test1_orig;
check(memcmp(&ftr_fixup_test1, &ftr_fixup_test1_orig, size) == 0);
We know that these are asm labels so it is safe to read up to 'size'
bytes at those addresses.
However, because we have passed the address of a single unsigned int to
memcmp, the compiler believes the underlying object is in fact a single
unsigned int. So if size > sizeof(unsigned int), there will be a panic
at runtime.
We can fix this by changing the types: instead of calling the asm labels
unsigned ints, call them unsigned int[]s. Therefore the size isn't
incorrectly determined at compile time and we get a regular unsafe
memcmp and no panic.
[1] http://openwall.com/lists/kernel-hardening/2017/05/09/2
Link: http://lkml.kernel.org/r/1497903987-21002-7-git-send-email-keescook@chromium.org
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
prom_init is a bit special; in theory it should be able to be linked
separately to the kernel. To keep this from getting too complex, the
symbols that prom_init.c uses are checked.
Fortification adds symbols, and it gets quite messy as it includes
things like panic(). So just don't fortify prom_init.c for now.
Link: http://lkml.kernel.org/r/1497903987-21002-6-git-send-email-keescook@chromium.org
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement an arch-speicfic watchdog rather than use the perf-based
hardlockup detector.
The new watchdog takes the soft-NMI directly, rather than going through
perf. Perf interrupts are to be made maskable in future, so that would
prevent the perf detector from working in those regions.
Additionally, implement a SMP based detector where all CPUs watch one
another by pinging a shared cpumask. This is because powerpc Book3S
does not have a true periodic local NMI, but some platforms do implement
a true NMI IPI.
If a CPU is stuck with interrupts hard disabled, the soft-NMI watchdog
does not work, but the SMP watchdog will. Even on platforms without a
true NMI IPI to get a good trace from the stuck CPU, other CPUs will
notice the lockup sufficiently to report it and panic.
[npiggin@gmail.com: honor watchdog disable at boot/hotplug]
Link: http://lkml.kernel.org/r/20170621001346.5bb337c9@roar.ozlabs.ibm.com
[npiggin@gmail.com: fix false positive warning at CPU unplug]
Link: http://lkml.kernel.org/r/20170630080740.20766-1-npiggin@gmail.com
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20170616065715.18390-6-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Tested-by: Babu Moger <babu.moger@oracle.com> [sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split SOFTLOCKUP_DETECTOR from LOCKUP_DETECTOR, and split
HARDLOCKUP_DETECTOR_PERF from HARDLOCKUP_DETECTOR.
LOCKUP_DETECTOR implies the general boot, sysctl, and programming
interfaces for the lockup detectors.
An architecture that wants to use a hard lockup detector must define
HAVE_HARDLOCKUP_DETECTOR_PERF or HAVE_HARDLOCKUP_DETECTOR_ARCH.
Alternatively an arch can define HAVE_NMI_WATCHDOG, which provides the
minimum arch_touch_nmi_watchdog, and it otherwise does its own thing and
does not implement the LOCKUP_DETECTOR interfaces.
sparc is unusual in that it has started to implement some of the
interfaces, but not fully yet. It should probably be converted to a full
HAVE_HARDLOCKUP_DETECTOR_ARCH.
[npiggin@gmail.com: fix]
Link: http://lkml.kernel.org/r/20170617223522.66c0ad88@roar.ozlabs.ibm.com
Link: http://lkml.kernel.org/r/20170616065715.18390-4-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Reviewed-by: Babu Moger <babu.moger@oracle.com>
Tested-by: Babu Moger <babu.moger@oracle.com> [sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vmcoreinfo_max_size stands for the vmcoreinfo_data, the correct one we
should use is vmcoreinfo_note whose total size is VMCOREINFO_NOTE_SIZE.
Like explained in commit 77019967f0 ("kdump: fix exported size of
vmcoreinfo note"), it should not affect the actual function, but we
better fix it, also this change should be safe and backward compatible.
After this, we can get rid of variable vmcoreinfo_max_size, let's use
the corresponding macros directly, fewer variables means more safety for
vmcoreinfo operation.
[xlpang@redhat.com: fix build warning]
Link: http://lkml.kernel.org/r/1494830606-27736-1-git-send-email-xlpang@redhat.com
Link: http://lkml.kernel.org/r/1493281021-20737-2-git-send-email-xlpang@redhat.com
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reviewed-by: Dave Young <dyoung@redhat.com>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Although it's not documented anywhere, there is an expectation that
atomic64_inc_not_zero() returns a result which fits in an int. This is
the behaviour implemented on all arches except powerpc.
This has caused at least one bug in practice, in the percpu-refcount
code, where the long result from our atomic64_inc_not_zero() was
truncated to an int leading to lost references and stuck systems. That
was worked around in that code in commit 966d2b04e0 ("percpu-refcount:
fix reference leak during percpu-atomic transition").
To the best of my grepping abilities there are no other callers
in-tree which truncate the value, but we should fix it anyway. Because
the breakage is subtle and potentially very harmful I'm also tagging
it for stable.
Code generation is largely unaffected because in most cases the
callers are just using the result for a test anyway. In particular the
case of fget() that was mentioned in commit a6cf7ed511
("powerpc/atomic: Implement atomic*_inc_not_zero") generates exactly
the same code.
Fixes: a6cf7ed511 ("powerpc/atomic: Implement atomic*_inc_not_zero")
Cc: stable@vger.kernel.org # v3.4
Noticed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
From POWER4 onwards, mfocrf() only places the specified CR field into
the destination GPR, and the rest of it is set to 0. The PowerPC AS
from version 3.0 now requires this behaviour.
The emulation code currently puts the entire CR into the destination GPR.
Fix it.
Fixes: 6888199f7f ("[POWERPC] Emulate more instructions in software")
Cc: stable@vger.kernel.org # v2.6.22+
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The mcrf emulation code was using the CR field number directly as the shift
value, without taking into account that CR fields are numbered from 0-7 starting
at the high bits. That meant it was looking at the CR fields in the reverse
order.
Fixes: cf87c3f6b6 ("powerpc: Emulate icbi, mcrf and conditional-trap instructions")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Similar to POWER8, POWER9 can count run cycles and run instructions
completed on more than one PMU.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In case of continous sampling (non-marked), the code currently
sets MMCRA[SDAR_MODE] to 0b01 (Update on TLB miss) for Power9 DD1.
On DD2 and later it copies the sdar_mode value from the event code,
which for most events is 0b00 (No updates).
However we must set a non-zero value for SDAR_MODE when doing
continuous sampling, so honor the event code, unless it's zero, in
which case we use use 0b01 (Update on TLB miss).
Fixes: 78b4416aa2 ("powerpc/perf: Handle sdar_mode for marked event in power9")
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Implement the show_options superblock op for spufs as part of a bid to get
rid of s_options and generic_show_options() to make it easier to implement
a context-based mount where the mount options can be passed individually
over a file descriptor.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeremy Kerr <jk@ozlabs.org>
cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The workaround for the CELL timebase bug does not correctly mark cr0 as
being clobbered. This means GCC doesn't know that the asm block changes cr0 and
might leave the result of an unrelated comparison in cr0 across the block, which
we then trash, leading to basically random behaviour.
Fixes: 859deea949 ("[POWERPC] Cell timebase bug workaround")
Cc: stable@vger.kernel.org # v2.6.19+
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Tweak change log and flag for stable]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are two cases outside the normal address space management
where a CPU's local TLB is to be flushed:
1. Host boot; in case something has left stale entries in the
TLB (e.g., kexec).
2. Machine check; to clean corrupted TLB entries.
CPU state restore from deep idle states also flushes the TLB.
However this seems to be a side effect of reusing the boot code to set
CPU state, rather than a requirement itself.
The current flushing has a number of problems with ISA v3.0B:
- The current radix mode of the MMU is not taken into account. tlbiel
is undefined if the R field does not match the current radix mode.
- ISA v3.0B hash must flush the partition and process table caches.
- ISA v3.0B radix must flush partition and process scoped translations,
partition and process table caches, and also the page walk cache.
Add POWER9 cases to handle these, with radix vs hash determined by the
host MMU mode.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that explicitly executed loaders are loaded in the mmap region, we
have more freedom to decide where we position PIE binaries in the
address space to avoid possible collisions with mmap or stack regions.
For 64-bit, align to 4GB to allow runtimes to use the entire 32-bit
address space for 32-bit pointers. On 32-bit use 4MB, which is the
traditional x86 minimum load location, likely to avoid historically
requiring a 4MB page table entry when only a portion of the first 4MB
would be used (since the NULL address is avoided).
Link: http://lkml.kernel.org/r/1498154792-49952-4-git-send-email-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Pratyush Anand <panand@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When writing to the process table, we need to ensure the store is
visible to a subsequent access by the MMU. We assume we never have
the PID active while doing the update, so a ptesync/isync pair
should hopefully be a big enough hammer for our purpose.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On radix, the process table entry we want to clear when destroying a
context is entry 0, not entry 1. This has no *immediate* consequence
on Power9, but it can cause other bugs to become worse.
Fixes: 7e381c0ff6 ("powerpc/mm/radix: Add mmu context handling callback for radix")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
That will allow OPAL to configure the CPU in an optimal way.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fixes a crash seen while doing a kexec from radix mode to
hash mode. Key 0 is special in hash and used in the RPN by default, we
set the key values to 0 today. In radix mode key 0 is used to control
supervisor<->user access. In hash key 0 is used by default, so the
first instruction after the switch causes a crash on kexec.
Commit 3b10d0095a ("powerpc/mm/radix: Prevent kernel execution of
user space") introduced the setting of IAMR and AMOR values to prevent
execution of user mode instructions from supervisor mode. We need to
clean up these SPR's on kexec.
Fixes: 3b10d0095a ("powerpc/mm/radix: Prevent kernel execution of user space")
Cc: stable@vger.kernel.org # v4.10+
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull perf fixes from Thomas Gleixner:
"A couple of fixes for perf and kprobes:
- Add he missing exclude_kernel attribute for the precise_ip level so
!CAP_SYS_ADMIN users get the proper results.
- Warn instead of failing completely when perf has no unwind support
for a particular architectiure built in.
- Ensure that jprobes are at function entry and not at some random
place"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kprobes: Ensure that jprobe probepoints are at function entry
kprobes: Simplify register_jprobes()
kprobes: Rename [arch_]function_offset_within_entry() to [arch_]kprobe_on_func_entry()
perf unwind: Do not fail due to missing unwind support
perf evsel: Set attr.exclude_kernel when probing max attr.precise_ip
Rename function_offset_within_entry() to scope it to kprobe namespace by
using kprobe_ prefix, and to also simplify it.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Suggested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/3aa6c7e2e4fb6e00f3c24fa306496a66edb558ea.1499443367.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
