Provide new implementation infrastructure that platforms may choose to use
when implementing the GPIO programming interface. Platforms can update their
GPIO support to use this. In many cases the incremental cost to access a
non-inlined GPIO should be less than a dozen instructions, with the memory
cost being about a page (total) of extra data and code. The upside is:
* Providing two features which were "want to have (but OK to defer)" when
GPIO interfaces were first discussed in November 2006:
- A "struct gpio_chip" to plug in GPIOs that aren't directly supported
by SOC platforms, but come from FPGAs or other multifunction devices
using conventional device registers (like UCB-1x00 or SM501 GPIOs,
and southbridges in PCs with more open specs than usual).
- Full support for message-based GPIO expanders, where registers are
accessed through sleeping I/O calls. Previous support for these
"cansleep" calls was just stubs. (One example: the widely used
pcf8574 I2C chips, with 8 GPIOs each.)
* Including a non-stub implementation of the gpio_{request,free}() calls,
making those calls much more useful. The diagnostic labels are also
recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot
of all GPIOs known to this infrastructure.
The driver programming interfaces introduced in 2.6.21 do not change at all;
this infrastructure is entirely below those covers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds PCI's accessor for segment_boundary_mask in device_dma_parameters.
The default segment_boundary is set to 0xffffffff, same to the block layer's
default value (and the scsi mid layer uses the same value).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds new accessors for segment_boundary_mask in device_dma_parameters
structure in the same way I did for max_segment_size. So we can easily change
where to place struct device_dma_parameters in the future.
dma_get_segment boundary returns 0xffffffff if dma_parms in struct device
isn't set up properly. 0xffffffff is the default value used in the block
layer and the scsi mid layer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This kills unused __clear_bit_string and find_next_zero_string (they
were used by only gart and calgary IOMMUs).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts PPC's IOMMU to use the IOMMU helper functions. The IOMMU
doesn't allocate a memory area spanning LLD's segment boundary anymore.
iseries_hv_alloc and iseries_hv_map don't have proper device
struct. 4GB boundary is used for them.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds IOMMU helper functions for the free area management. These
functions take care of LLD's segment boundary limit for IOMMUs. They would be
useful for IOMMUs that use bitmap for the free area management.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds struct device_dma_parameters in struct pci_dev and properly
sets up a pointer in struct device.
The default max_segment_size is set to 64K, same to the block layer's
default value.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Mostly-acked-by: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IOMMUs merges scatter/gather segments without considering a low level
driver's restrictions. The problem is that IOMMUs can't access to the
limitations because they are in request_queue.
This patchset introduces a new structure, device_dma_parameters,
including dma information. A pointer to device_dma_parameters is added
to struct device. The bus specific structures (like pci_dev) includes
device_dma_parameters. Low level drivers can use dma_set_max_seg_size
to tell IOMMUs about the restrictions.
We can move more dma stuff in struct device (like dma_mask) to struct
device_dma_parameters later (needs some cleanups before that).
This includes patches for all the IOMMUs that could merge sg (x86_64,
ppc, IA64, alpha, sparc64, and parisc) though only the ppc patch was
tested. The patches for other IOMMUs are only compile tested.
This patch:
Add a new structure, device_dma_parameters, including dma information. A
pointer to device_dma_parameters is added to struct device.
- there are only max_segment_size and segment_boundary_mask there but we'll
move more dma stuff in struct device (like dma_mask) to struct
device_dma_parameters later. segment_boundary_mask is not supported yet.
- new accessors for the dma parameters are added. So we can easily change
where to place struct device_dma_parameters in the future.
- dma_get_max_seg_size returns 64K if dma_parms in struct device isn't set
up properly. 64K is the default max_segment_size in the block layer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the private_data field to be specified in platform_data for the
standard 8250/16550 UART. This field is used by DW APB type UARTs and
without this patch it's only possible to set this field when registering
the port by hand. If private_data is not set then the driver will
potentially oops with a NULL pointer dereference.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove kio_addr_t, and replace it with unsigned int. No known architecture
needs more than 32 bits for IO addresses and ports and having a separate type
for it is just messy.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the io_req_t members to unsigned int, to allow use on machines with
more than 16 bits worth of IO ports (i.e. secondary busses on ppc64, etc).
There was only a couple of places in drivers where a change was needed. I
left printk formats alone (there are lots of %04x-style formats in there),
mostly to not change the format on the platforms that only have 16-bit io
addresses, but also because the padding doesn't really add all that much value
most of the time.
I found only one sprintf of an address, and upsized the string accordingly (I
doubt anyone will have anywhere near INT_MAX as irq value, but at least
there's room for it now).
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CC [M] sound/ppc/awacs.o
In file included from sound/ppc/awacs.c:24:
include/asm/nvram.h:62: error: field 'partition' has incomplete type
Reported-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
FATAL: drivers/bluetooth/btsdio: sizeof(struct sdio_device_id)=12 is not a modulo of the size of section __mod_sdio_device_table=30.
Fix definition of struct sdio_device_id in mod_devicetable.h
m68k has 16bit alignment for unsigned long.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Pierre Ossman <drzeus@drzeus.cx>
CC: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wires up the new timerfd API to the x86 family.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the new timerfd API as it is implemented by the following patch:
int timerfd_create(int clockid, int flags);
int timerfd_settime(int ufd, int flags,
const struct itimerspec *utmr,
struct itimerspec *otmr);
int timerfd_gettime(int ufd, struct itimerspec *otmr);
The timerfd_create() API creates an un-programmed timerfd fd. The "clockid"
parameter can be either CLOCK_MONOTONIC or CLOCK_REALTIME.
The timerfd_settime() API give new settings by the timerfd fd, by optionally
retrieving the previous expiration time (in case the "otmr" parameter is not
NULL).
The time value specified in "utmr" is absolute, if the TFD_TIMER_ABSTIME bit
is set in the "flags" parameter. Otherwise it's a relative time.
The timerfd_gettime() API returns the next expiration time of the timer, or
{0, 0} if the timerfd has not been set yet.
Like the previous timerfd API implementation, read(2) and poll(2) are
supported (with the same interface). Here's a simple test program I used to
exercise the new timerfd APIs:
http://www.xmailserver.org/timerfd-test2.c
[akpm@linux-foundation.org: coding-style cleanups]
[akpm@linux-foundation.org: fix ia64 build]
[akpm@linux-foundation.org: fix m68k build]
[akpm@linux-foundation.org: fix mips build]
[akpm@linux-foundation.org: fix alpha, arm, blackfin, cris, m68k, s390, sparc and sparc64 builds]
[heiko.carstens@de.ibm.com: fix s390]
[akpm@linux-foundation.org: fix powerpc build]
[akpm@linux-foundation.org: fix sparc64 more]
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I think that advancing the timer against the timer's current "now" can be a
pretty common usage, so, w/out exposing hrtimer's internals, we add a new
hrtimer_forward_now() function.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As Roland pointed out, we have the very old problem with exec. de_thread()
sets SIGNAL_GROUP_EXIT, kills other threads, changes ->group_leader and then
clears signal->flags. All signals (even fatal ones) sent in this window
(which is not too small) will be lost.
With this patch exec doesn't abuse SIGNAL_GROUP_EXIT. signal_group_exit(),
the new helper, should be used to detect exit_group() or exec() in progress.
It can have more users, but this patch does only strictly necessary changes.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robin Holt <holt@sgi.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was dumb to make get_task_comm() return void. Change it to return a
pointer to the resulting output for caller convenience.
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Sat, 2008-01-05 at 13:35 -0800, Davide Libenzi wrote:
> I remember I talked with Arjan about this time ago. Basically, since 1)
> you can drop an epoll fd inside another epoll fd 2) callback-based wakeups
> are used, you can see a wake_up() from inside another wake_up(), but they
> will never refer to the same lock instance.
> Think about:
>
> dfd = socket(...);
> efd1 = epoll_create();
> efd2 = epoll_create();
> epoll_ctl(efd1, EPOLL_CTL_ADD, dfd, ...);
> epoll_ctl(efd2, EPOLL_CTL_ADD, efd1, ...);
>
> When a packet arrives to the device underneath "dfd", the net code will
> issue a wake_up() on its poll wake list. Epoll (efd1) has installed a
> callback wakeup entry on that queue, and the wake_up() performed by the
> "dfd" net code will end up in ep_poll_callback(). At this point epoll
> (efd1) notices that it may have some event ready, so it needs to wake up
> the waiters on its poll wait list (efd2). So it calls ep_poll_safewake()
> that ends up in another wake_up(), after having checked about the
> recursion constraints. That are, no more than EP_MAX_POLLWAKE_NESTS, to
> avoid stack blasting. Never hit the same queue, to avoid loops like:
>
> epoll_ctl(efd2, EPOLL_CTL_ADD, efd1, ...);
> epoll_ctl(efd3, EPOLL_CTL_ADD, efd2, ...);
> epoll_ctl(efd4, EPOLL_CTL_ADD, efd3, ...);
> epoll_ctl(efd1, EPOLL_CTL_ADD, efd4, ...);
>
> The code "if (tncur->wq == wq || ..." prevents re-entering the same
> queue/lock.
Since the epoll code is very careful to not nest same instance locks
allow the recursion.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove BUILD_BUG_ON() in vmem code since it causes build failures if
the size of struct page increases. Instead calculate at compile time
the address of the highest physical address that can be added to the
1:1 mapping.
This supposed to fix a build failure with the page owner tracking leak
detector patches as reported by akpm.
page-owner-tracking-leak-detector-broken-on-s390.patch can be removed
from -mm again when this is merged.
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fixes this compile error:
fs/ext4/mballoc.c:
In function 'ext4_mb_generate_buddy':
fs/ext4/mballoc.c:954:
error: implicit declaration of function 'generic_find_next_le_bit'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The bitops header is now a bit shorter and easier to understand since
it uses less inline assembly. It requires some tricks to persuade the
compiler to generate decent code. The ffz/ffs functions now use the
_zb_findmap/_sb_findmap table as well.
With this cleanup the new bitops for ext4 can be implemented with a
few lines, instead of another large inline assembly.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This intendeds to make proper shutdown of qeth devices easier.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide a way to use tc filters on vlan tag even if tag is buried in
skb due to hardware acceleration.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if_addrlabel.h is needed for iproute2 usage.
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the following no longer used functions:
- rtattr_parse()
- rtattr_strlcpy()
- __rtattr_parse_nested_compat()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port offset calculations depend on the protocol family, but, as
Adrian noticed, I broke this logic with the commit
5ee31fc1ec
[INET]: Consolidate inet(6)_hash_connect.
Return this logic back, by passing the port offset directly into the
consolidated function.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Noticed-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ipv6_icmp_sysctl_init and ipv6_route_sysctl_init into the right
ifdef section otherwise that does not compile when CONFIG_SYSCTL=yes
and CONFIG_PROC_FS=no
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
compile error building without CONFIG_FS_PROC:
net/ipv4/fib_frontend.c: In function 'fib_net_init':
net/ipv4/fib_frontend.c:1032: error: implicit declaration of function 'fib_proc_
init'
net/ipv4/fib_frontend.c: In function 'fib_net_exit':
net/ipv4/fib_frontend.c:1047: error: implicit declaration of function 'fib_proc_
exit'
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bumps the AGP interface to 0.103.
Certain Intel chipsets contains a global write buffer, and this can require
flushing from the drm or X.org to make sure all data has hit RAM before
initiating a GPU transfer, due to a lack of coherency with the integrated
graphics device and this buffer.
This just adds generic support to the AGP interfaces, a follow-on patch
will add support to the Intel driver to use this interface.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The only in kernel use of ia64_set_psr() needs to follow
it with a srlz.i (since it is changing state for PSR.ic).
So it is pointless to issue srlz.d inside this function.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Since kvm/module needs to use some unexported functions in kernel,
so export them with this patch.
Signed-off-by: Zhang Xiantao <xiantao.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
...
- I removed the unnecessary barrier() from __clear_bit_unlock().
ia64_st4_rel_nta() makes sure all the modifications are globally
seen before the bit is seen to be off.
- I made __clear_bit() modeled after __set_bit() and __change_bit().
- I corrected some comments sating that a memory barrier is provided,
yet in reality, it is the acquisition side of the memory barrier only.
- I corrected some comments, e.g. test_and_clear_bit() was peaking
about "bit to set".
Signed-off-by: Zoltan Menyhart, <Zoltan.Menyhart@bull.net>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fixes userspace build errors when linux/ipv6.h is included such as in the
dhcpv6 package under fedora. Likely causes other userspace build errors as
well. I found this in akpm's tree from 2.6.18 but could not find any case
of anyone proposing it for the main tree.
Signed-off-by: Doug Chapman <doug.chapman@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'slub-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/christoph/vm:
Explain kmem_cache_cpu fields
SLUB: Do not upset lockdep
SLUB: Fix coding style violations
Add parameter to add_partial to avoid having two functions
SLUB: rename defrag to remote_node_defrag_ratio
Move count_partial before kmem_cache_shrink
SLUB: Fix sysfs refcounting
slub: fix shadowed variable sparse warnings
Add some comments explaining the fields of the kmem_cache_cpu structure.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The NUMA defrag works by allocating objects from partial slabs on remote
nodes. Rename it to
remote_node_defrag_ratio
to be clear about this.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
* at91:
[ARM] 4802/1: Fix typo and remove vague comment
[ARM] 4660/3: at91: allow selecting UART for early kernel messages
[ARM] 4739/1: at91sam9263: make gpio bank C and D irqs work
* ixp:
[ARM] 4809/2: ixp4xx: Merge dsmg600-power.c into dsmg600-setup.c
[ARM] 4808/2: ixp4xx: Merge nas100d-power.c into nas100d-setup.c
[ARM] 4807/2: ixp4xx: Merge nslu2-power.c into nslu2-setup.c
[ARM] 4806/1: ixp4xx: Ethernet support for the nslu2 and nas100d boards
[ARM] 4805/1: ixp4xx: Use leds-gpio driver instead of IXP4XX-GPIO-LED driver
[ARM] 4715/2: Ethernet support for IXDP425 boards
[ARM] 4714/2: Headers for IXP4xx built-in Ethernet and WAN drivers
[ARM] 4713/3: Adds drivers for IXP4xx QMgr and NPE features
[ARM] 4712/2: Adds functions to read and write IXP4xx "feature" bits
[ARM] 4774/2: ixp4xx: Register dsmg600 rtc i2c_board_info
[ARM] 4773/2: ixp4xx: Register nas100d rtc i2c_board_info
[ARM] 4772/2: ixp4xx: Register nslu2 rtc i2c_board_info
[ARM] 4769/2: ixp4xx: Button updates for the dsmg600 board
[ARM] 4768/2: ixp4xx: Button and LED updates for the nas100d board
[ARM] 4767/2: ixp4xx: Add bitops.h include to io.h
[ARM] 4766/2: ixp4xx: Update ixp4xx_defconfig, enabling all supported boards
* master:
[ARM] 4810/1: - Fix 'section mismatch' building warnings
[ARM] xtime_seqlock: fix more ARM machines for xtime deadlocking
[ARM] 21285 serial: fix build error
* misc:
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
* pxa:
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
[ARM] pxa: fix the warning of undeclared "struct pxaohci_platform_data"
[ARM] pxa: change set_kset_name() to direct name assignment for MFP sysclass
* realview:
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
This patch changes the REALVIEW_MPCORE configuration option to
REALVIEW_EB_ARM11MP since this is only specific to RealView/EB.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch modifies the get_irqnr_preamble macro to work with multiple
platforms at run-time by reading the address of the GIC controller from
the gic_cpu_base_addr variable. This variable is defined in core.c and
intialised in realview_eb.c (gic_init_irq).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the core-tile detection and only enables devices if the
corresponding tile is present. It currently detects the ARM11MPCore via
the core_tile_eb11mp() macro.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves the platform specific definitions from platform.h into
the board-eb.h file. It drops the INT_* definitions as they are no
longer used in irqs.h (moved to board-eb.h). It renames REALVIEW_*
macros to REALVIEW_EB_* or REALVIEW_EB11MP_* to distinguish between
standard EB and EB + the ARM11MPCore tile. The platform.h file contains
common definitions to the RealView platforms and it is only directly
included in board-*.h files.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch registers the local timers on ARM11MPCore as clock event
devices. The clock device can be set up as periodic or oneshot.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds dummy local timers for each CPU so that the board clock
device is used to broadcast events to the other CPUs. The patch also
adds the declaration for the dummy_timer_setup function (the equivalent
of local_timer_setup when CONFIG_LOCAL_TIMERS is not set).
Due to the way clockevents work, the dummy timer on the first CPU has to
be registered before the board timer.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the smp_call_function_single and smp_timer_broadcast
functions and modifies ipi_timer to call the platform-specific function
local_timer_interrupt.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (25 commits)
virtio: balloon driver
virtio: Use PCI revision field to indicate virtio PCI ABI version
virtio: PCI device
virtio_blk: implement naming for vda-vdz,vdaa-vdzz,vdaaa-vdzzz
virtio_blk: Dont waste major numbers
virtio_blk: provide getgeo
virtio_net: parametrize the napi_weight for virtio receive queue.
virtio: free transmit skbs when notified, not on next xmit.
virtio: flush buffers on open
virtnet: remove double ether_setup
virtio: Allow virtio to be modular and used by modules
virtio: Use the sg_phys convenience function.
virtio: Put the virtio under the virtualization menu
virtio: handle interrupts after callbacks turned off
virtio: reset function
virtio: populate network rings in the probe routine, not open
virtio: Tweak virtio_net defines
virtio: Net header needs hdr_len
virtio: remove unused id field from struct virtio_blk_outhdr
virtio: clarify NO_NOTIFY flag usage
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
scsi: fix dependency bug in aic7 Makefile
kbuild: add svn revision information to setlocalversion
kbuild: do not warn about __*init/__*exit symbols being exported
Move Kconfig.instrumentation to arch/Kconfig and init/Kconfig
Add HAVE_KPROBES
Add HAVE_OPROFILE
Create arch/Kconfig
Fix ARM to play nicely with generic Instrumentation menu
kconfig: ignore select of unknown symbol
kconfig: mark config as changed when loading an alternate config
kbuild: Spelling/grammar fixes for config DEBUG_SECTION_MISMATCH
Remove __INIT_REFOK and __INITDATA_REFOK
kbuild: print only total number of section mismatces found
Global functions should include their prototypes.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fixes sparse warning:
arch/x86/kernel/cpu/intel.c:48:15: warning: symbol 'ppro_with_ram_bug' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A few snuck back in to x86.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that the only user does it on its own remove the NUMAQ support macros
in io_32.h
The next step would be to convert the preprocessor mess to actually readable
standard inlines.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
numa.c is the only user of the {in,out}*_quad functions. And it has only a few call
sites. Change them to open code the magic NUMAQ port access.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove bogus reference to "Pentium-II erratum A13" and point to the
actual canonical source of information about what requirements x86
processors have for PAE pagetable updates.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rather than unconditionally reloading cr3, only do so if the pud we're
updating is within the active pgd.
This eliminates TLB flushes most of the time. The
performance-critical uses of pud_clear are during execve and exit, but
in those cases cr3 is referring to some other pagetable. The only
other use of pud_clear is during a large (1Gbyte+) munmap, and those
are sufficiently rare that a couple of cr3 reloads won't hurt.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Revert "defer cr3 reload when doing pud_clear()" since I'm going to
replace it.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove unused <linux/quicklist.h> from <asm-generic/tlb.h>; per
Christoph Lameter this should have been part of a previous patch
reversal but apparently didn't get removed.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the CPU feature string names to a separate file (common to 32
and 64 bits); additionally, make <asm/cpufeature.h> includable by host
code in preparation for including the CPU feature strings in the boot
code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The volatile keyword was removed from the clflush() prototype
in commit e34907ae180f4fe6c28bb4516c679c2f81b0c9ed; the comment there
states:
x86: remove volatile keyword from clflush.
the p parameter is an explicit memory reference, and is
enough to prevent gcc to being nasty here. The volatile
seems completely not needed.
This reflects incorrect understanding of the function of the volatile
keyword there. The purpose of the volatile keyword is informing gcc
that it is safe to pass a volatile pointer to this function.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the _ASM_EXTABLE macro from <asm/asm.h>, instead of open-coding
__ex_table entires in include/asm-x86/uaccess_64.h.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the _ASM_EXTABLE macro from <asm/asm.h>, instead of open-coding
__ex_table entires in include/asm-x86/uaccess_32.h.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the _ASM_EXTABLE macro from <asm/asm.h>, instead of open-coding
__ex_table entires in include/asm-x86/system.h.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the _ASM_EXTABLE macro from <asm/asm.h>, instead of open-coding
__ex_table entires in include/asm-x86/msr.h.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the _ASM_EXTABLE macro from <asm/asm.h>, instead of open-coding
__ex_table entires in include/asm-x86/i387.h.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the _ASM_EXTABLE macro from <asm/asm.h>, instead of open-coding
__ex_table entires in include/asm-x86/futex.h.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Instead of open-coding the __ex_table information at each callsite,
construct a common macro that can work regardless of CPU size.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (77 commits)
[IPV6]: Reorg struct ifmcaddr6 to save some bytes
[INET_TIMEWAIT_SOCK]: Reorganize struct inet_timewait_sock to save some bytes
[DCCP]: Reorganize struct dccp_sock to save 8 bytes
[INET6]: Reorganize struct inet6_dev to save 8 bytes
[SOCK] proto: Add hashinfo member to struct proto
EMAC driver: Fix bug: The clock divisor is set to all ones at reset.
EMAC driver: fix bug - invalidate data cache of new_skb->data range when cache is WB
EMAC driver: add power down mode
EMAC driver: ADSP-BF52x arch/mach support
EMAC driver: use simpler comment headers and strip out information that is maintained in the scm's log
EMAC driver: bf537 MAC multicast hash filtering patch
EMAC driver: define MDC_CLK=2.5MHz and caculate mdc_div according to SCLK.
EMAC driver: shorten the mdelay value to solve netperf performance issue
[netdrvr] sis190: build fix
sky2: fix Wake On Lan interaction with BIOS
sky2: restore multicast addresses after recovery
pci-skeleton: Misc fixes to build neatly
phylib: Add Realtek 821x eth PHY support
natsemi: Update locking documentation
PHYLIB: Locking fixes for PHY I/O potentially sleeping
...
Currently, the atags used by kexec are fixed to the ones originally used
to boot the kernel. This is less than ideal as changing the commandline,
initrd and other options would be a useful feature.
This patch exports the atags used for the current kernel to userspace
through an "atags" file in procfs. The presence of the file is
controlled by its own Kconfig option and cleans up several ifdef blocks
into a separate file. The tags for the new kernel are assumed to be at
a fixed location before the kernel image itself. The location of the
tags used to boot the original kernel is unimportant and no longer
saved.
Based on a patch from Uli Luckas <u.luckas@road.de>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. clear RDH bit after resuming back from D3, otherwise, the multi function
pins will retain the low power state
2. save/restore essential system registers
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix typo and remove vague comment
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently early kernel messages, i.e., those from uncompression, go to the
debugging UART. And if it is enabled in the platform configuration, but
not initialized by the bootloader, the machine hangs, waiting for UART
status change. Besides, having those messages on another UART - typically
the console UART - may be preferrable. This patch allows selecting the
UART in kernel configuration.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no reason to have power control in a separate file from the
board setup code. Merge it back into the board setup file, removing
superfluous header includes and removing superfluous constants from
the machine header file.
--
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds platform structs and #defines required by drivers for
IXP4xx built-in Ethernet and WAN (sync serial) ports.
The actual drivers will reside in drivers/net/arm and
drivers/net/wan and will be submitted separately.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds drivers for IXP4xx hardware Queue Manager and for
Network Processor Engines. Requires patch #4712 (reading/writing
CPU feature (aka fuse) bits).
Posted to linux-arm-kernel on 2 Dec 2007 and revised.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds functions to read and write IXP4xx "feature" (aka "fuse")
bits, containing information about available/enabled CPU features.
The uncompress.h included by boot/compressed/misc.c resides in
a different space than rest of the kernel and thus can't use
asm/hardware.h (including asm/arch/cpu.h - which, in turn, may use
EXPORTed symbol "processor_id").
Posted to linux-arm-kernel on 2 Dec 2007 and revised.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Remove the superfluous declaration of ctrl_alt_del().
* Convert GPIO and IRQ handling to use the <asm/gpio.h> api.
* Perform the reset on the release of the power button, so that
NAS devices which have been set to auto-power-on (by solder
bridging the power button) do not continuously power cycle.
* Remove all superflous constants from dsmg600.h
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Convert GPIO and IRQ handling to use the <asm/gpio.h> api.
* Perform the reset only after the power button has been held down
for at least two seconds. Do the reset on the release of the power
button, so that NAS devices which have been set to auto-power-on (by
solder bridging the power button) do not continuously power cycle.
* Remove all superflous constants from nas100d.h
* Add LED constants to nas100d.h while we're there.
* Update the board LED setup code to use those constants.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add include of <linux/bitops.h> to io.h to solve compilations errors in
files such as drivers/w1/w1_io.c caused by the ixp4xx version of io.h
using the BIT() macro without including <linux/bitops.h> first.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After discussions with Anthony Liguori, it seems that the virtio
balloon can be made even simpler. Here's my attempt.
The device configuration tells the driver how much memory it should
take from the guest (ie. balloon size). The guest feeds the page
numbers it has taken via one virtqueue.
A second virtqueue feeds the page numbers the driver wants back: if
the device has the VIRTIO_BALLOON_F_MUST_TELL_HOST bit, then this
queue is compulsory, otherwise it's advisory (and the guest can simply
fault the pages back in).
This driver can be enhanced later to deflate the balloon via a
shrinker, oom callback or we could even go for a complete set of
in-guest regulators.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
As Avi pointed out, as we continue to massage the virtio PCI ABI, we can make
things a little more friendly to users by utilizing the PCI revision field to
indicate which version of the ABI we're using. This is a hard ABI version
and incrementing it will cause the guest driver to break.
This is the necessary changes to virtio_pci to support this.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is a PCI device that implements a transport for virtio. It allows virtio
devices to be used by QEMU based VMMs like KVM or Xen.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A reset function solves three problems:
1) It allows us to renegotiate features, eg. if we want to upgrade a
guest driver without rebooting the guest.
2) It gives us a clean way of shutting down virtqueues: after a reset,
we know that the buffers won't be used by the host, and
3) It helps the guest recover from messed-up drivers.
So we remove the ->shutdown hook, and the only way we now remove
feature bits is via reset.
We leave it to the driver to do the reset before it deletes queues:
the balloon driver, for example, needs to chat to the host in its
remove function.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
1) Turn GSO on virtio net into an all-or-nothing (keep checksumming
separate). Having multiple bits is a pain: if you can't support something
you should handle it in software, which is still a performance win.
2) Make VIRTIO_NET_HDR_GSO_ECN a flag in the header, so it can apply to
IPv6 or v4.
3) Rename VIRTIO_NET_F_NO_CSUM to VIRTIO_NET_F_CSUM (ie. means we do
checksumming).
4) Add csum and gso params to virtio_net to allow more testing.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It's far easier to deal with packets if we don't have to parse the
packet to figure out the header length to know how much to pull into
the skb data. Add the field to the virtio_net_hdr struct (and fix the
spaces that somehow crept in there).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This field has been unused since an older version of virtio. Remove
it now before we freeze the ABI.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au.
The other side (host) can set the NO_NOTIFY flag as an optimization,
to say "no need to kick me when you add things". Make it clear that
this is advisory only; especially that we should always notify when
the ring is full.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Using unsigned int resulted in silent truncation of the upper 32-bit
on x86_64 resulting in an OOPS since the ring was being initialized
wrong.
Please reconsider my previous patch to just use PAGE_ALIGN(). Open
coding this sort of stuff, no matter how simple it seems, is just
asking for this sort of trouble.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Various drivers want to know when their configuration information
changes: the balloon driver is the immediate user, but the network
driver may one day have a "carrier" status as well.
This introduces that callback (lguest doesn't use it yet).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It seems that virtio_net wants to disable callbacks (interrupts) before
calling netif_rx_schedule(), so we can't use the return value to do so.
Rename "restart" to "cb_enable" and introduce "cb_disable" hook: callback
now returns void, rather than a boolean.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Previously we used a type/len pair within the config space, but this
seems overkill. We now simply define a structure which represents the
layout in the config space: the config space can now only be extended
at the end.
The main driver-visible changes:
1) We indicate what fields are present with an explicit feature bit.
2) Virtqueues are explicitly numbered, and not in the config space.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Use it in virtio_net (replacing buggy version there), it's also going
to be used by TAP for partial csum support.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: David S. Miller <davem@davemloft.net>
fcntl(F_GETLK,..) can return pid of process for not current pid namespace
(if process is belonged to the several namespaces). It is true also for
pids in /proc/locks. So correct behavior is saving pointer to the struct
pid of the process lock owner.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Function do_timer_interrupt_hook() don't take argument regs,
and structure hrtimer_sleeper don't have member cb_pending.
So delete comments refering to these symbols.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
There is an unmatched parenthesis in the locking commentary of radix_tree.h
which is trivially fixed by the patch below.
Signed-off-by: Tim Pepper <lnxninja@linux.vnet.ibm.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Mark comment as comment, fixes:
include/asm/vga.h:6:8: warning: extra tokens at end of #endif directive
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
My first guess for "fujitsu" was it might be related to the
fujitsu-laptop.c driver...
Move the frv directory one level up since frv is the name of the
architecture in the Linux kernel.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Having the macro to prevent multiple inclusion of
include/linux/dma-mapping.h contain the prefix "_ASM" is just begging
for possible confusion some day.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
This way we can remove TCP and DCCP specific versions of
sk->sk_prot->get_port: both v4 and v6 use inet_csk_get_port
sk->sk_prot->hash: inet_hash is directly used, only v6 need
a specific version to deal with mapped sockets
sk->sk_prot->unhash: both v4 and v6 use inet_hash directly
struct inet_connection_sock_af_ops also gets a new member, bind_conflict, so
that inet_csk_get_port can find the per family routine.
Now only the lookup routines receive as a parameter a struct inet_hashtable.
With this we further reuse code, reducing the difference among INET transport
protocols.
Eventually work has to be done on UDP and SCTP to make them share this
infrastructure and get as a bonus inet_diag interfaces so that iproute can be
used with these protocols.
net-2.6/net/ipv4/inet_hashtables.c:
struct proto | +8
struct inet_connection_sock_af_ops | +8
2 structs changed
__inet_hash_nolisten | +18
__inet_hash | -210
inet_put_port | +8
inet_bind_bucket_create | +1
__inet_hash_connect | -8
5 functions changed, 27 bytes added, 218 bytes removed, diff: -191
net-2.6/net/core/sock.c:
proto_seq_show | +3
1 function changed, 3 bytes added, diff: +3
net-2.6/net/ipv4/inet_connection_sock.c:
inet_csk_get_port | +15
1 function changed, 15 bytes added, diff: +15
net-2.6/net/ipv4/tcp.c:
tcp_set_state | -7
1 function changed, 7 bytes removed, diff: -7
net-2.6/net/ipv4/tcp_ipv4.c:
tcp_v4_get_port | -31
tcp_v4_hash | -48
tcp_v4_destroy_sock | -7
tcp_v4_syn_recv_sock | -2
tcp_unhash | -179
5 functions changed, 267 bytes removed, diff: -267
net-2.6/net/ipv6/inet6_hashtables.c:
__inet6_hash | +8
1 function changed, 8 bytes added, diff: +8
net-2.6/net/ipv4/inet_hashtables.c:
inet_unhash | +190
inet_hash | +242
2 functions changed, 432 bytes added, diff: +432
vmlinux:
16 functions changed, 485 bytes added, 492 bytes removed, diff: -7
/home/acme/git/net-2.6/net/ipv6/tcp_ipv6.c:
tcp_v6_get_port | -31
tcp_v6_hash | -7
tcp_v6_syn_recv_sock | -9
3 functions changed, 47 bytes removed, diff: -47
/home/acme/git/net-2.6/net/dccp/proto.c:
dccp_destroy_sock | -7
dccp_unhash | -179
dccp_hash | -49
dccp_set_state | -7
dccp_done | +1
5 functions changed, 1 bytes added, 242 bytes removed, diff: -241
/home/acme/git/net-2.6/net/dccp/ipv4.c:
dccp_v4_get_port | -31
dccp_v4_request_recv_sock | -2
2 functions changed, 33 bytes removed, diff: -33
/home/acme/git/net-2.6/net/dccp/ipv6.c:
dccp_v6_get_port | -31
dccp_v6_hash | -7
dccp_v6_request_recv_sock | +5
3 functions changed, 5 bytes added, 38 bytes removed, diff: -33
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY read/write functions can potentially sleep (e.g., a PHY accessed
via I2C). The following changes were made to account for this:
* Change spin locks to mutex locks
* Add a BUG_ON() to phy_read() phy_write() to warn against
calling them from an interrupt context.
* Use work queue for PHY state machine handling since
it can potentially sleep
* Change phydev lock from spinlock to mutex
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 312b1485fb made __INIT_REFOK expand
into .section .section ".ref.text", "ax". Since the assembler doesn't
tolerate stuttering in the source that broke all MIPS builds.
Since with this change Sam downgraded __INIT_REFOK to just a backward
compat thing and there being only a single use in the MIPS arch code the
best solution is to delete both of __INIT_REFOK and __INITDATA_REFOK (which
was equally broken) being unused anyway these can be deleted.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Move the declaration of device_pm_schedule_removal() to device.h
and make it exported, as it will be used directly by some drivers
for unregistering device objects during suspend/resume cycles in a
safe way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 6c723d5bd8.
It caused build errors on non-x86 platforms, config file confusion, and
even some boot errors on some x86-64 boxes. All around, not quite ready
for prime-time :(
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Move check_dma_crc() to ide-dma.c and add inline version for
CONFIG_BLK_DEV_IDEDMA=n case.
* Rename check_dma_crc() to ide_check_dma_crc().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* siimage.c: use hwif->sata_scr[SATA_{ERROR,STATUS}_OFFSET] instead of
SATA_{ERROR,STATUS}_REG macros.
* Remove no longer needed SATA_*_REG macros.
While at it:
* Remove needless SATA Status register read from sil_sata_reset_poll().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ->nice0 and ->nice2 ide_drive_t fields are always zero so remove them.
* IDE_NICE_0 and IDE_NICE_2 defines from <linux/hdreg.h> are no longer
used by any kernel code so cover them with #ifndef/#endif __KERNEL__.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Un-static create_proc_ide_drives() and call it from ide_device_add_all().
While at it:
* Rename create_proc_ide_drives() to ide_proc_port_register_devices().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out devices setup from ide_acpi_init() to
ide_acpi_port_init_devices().
* Call ide_acpi_port_init_devices() in ide_device_add_all().
While at it:
* Remove no longer needed 'drive' field from struct ide_acpi_drive_link.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->port_init_devs method to ide_hwif_t for a host specific
initialization of devices on a port. Call the new method from
ide_port_init_devices().
* Convert ht6560b, qd65xx and opti621 host drivers to use the new
->port_init_devs method.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use the same bit for IDE_HFLAG_CS5520 and IDE_HFLAG_VDMA host flags
(both are used only by cs5520 host driver currently).
* Add IDE_HFLAG_NO_IO32_BIT host flag and use it instead of ->no_io_32bit
ide_hwif_t field.
* Add IDE_HFLAG_NO_UNMASK_IRQS host flag, then convert dtc2278 and rz1000
host drivers to use it.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out code for finding ide_hwifs[] slot from ide_register_hw()
to ide_deprecated_find_port().
* Convert bast-ide, ide-cs and delkin_cb host drivers to use ide_device_add()
instead of ide_register_hw() (while at it drop doing "ide_unregister()" loop
which tries to unregister _all_ IDE interfaces if useable ide_hwifs[] slot
cannot be find).
This patch leaves us with only two ide_register_hw() users:
- drivers/macintosh/mediabay.c
- drivers/ide/ide.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'init_default' (flag for calling init_hwif_default()) and 'restore'
(flag for calling ide_hwif_restore()) arguments to ide_unregister().
* Update ide_unregister() users to set 'init_default' and 'restore' flags.
* No need to set 'init_default' flag in ide_register_hw() if the setup done
by init_hwif_default() is going to be overridden by ide_init_port_hw().
* No need to set 'init_default' and 'restore' flags in cleanup_module().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also, move xfer_func_t typedef to the ide.h since it is used by two drivers
now (more coming).
Bart:
- use __func__ while at it
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->cable_detect method to ide_hwif_t.
* Call the new method in ide_init_port() if:
- the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
- DMA initialization was successful (if hwif->dma_base is not set
ide_init_port() sets hwif->ultra_mask to zero)
- "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')
* Convert PCI host drivers to use ->cable_detect method.
While at it:
* Factor out cable detection to separate functions (if not already done).
* hpt366.c/it8213.c/slc90e66.c:
- don't check cable type if "idex=ata66" is used
* pdc202xx_new.c:
- add __devinit tag to pdcnew_cable_detect()
* pdc202xx_old.c:
- rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
- add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove 'struct pci_dev *dev' argument from ide_hwif_setup_dma().
* Un-static ide_hwif_setup_dma() and add CONFIG_BLK_DEV_IDEDMA_PCI=n version.
* Add 'const struct ide_port_info *d' argument to ide_device_add[_all]().
* Factor out generic ports init from ide_pci_setup_ports() to ide_init_port(),
move it to ide-probe.c and call it in in ide_device_add_all() instead of
ide_pci_setup_ports().
* Move ->mate setup to ide_device_add_all() from ide_port_init().
* Add IDE_HFLAG_NO_AUTOTUNE host flag for host drivers that don't enable
->autotune currently.
* Setup hwif->chipset in ide_init_port() but iff pi->chipset is set
(to not override setup done by ide_hwif_configure()).
* Add ETRAX host handling to ide_device_add_all().
* cmd640.c: set IDE_HFLAG_ABUSE_* also for CONFIG_BLK_DEV_CMD640_ENHANCED=n.
* pmac.c: make pmac_ide_setup_dma() return an error value and move DMA masks
setup to pmac_ide_setup_device().
* Add 'struct ide_port_info' instances to legacy host drivers, pass them to
ide_device_add() calls and then remove open-coded ports initialization.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.infradead.org/battery-2.6:
apm_power: check I.intval for zero value, we use it as the divisor
MAINTAINERS: remove kernel-discuss@handhelds.org list
pda_power: implement polling
pda_power: various cleanups
apm_power: support using VOLTAGE_* properties for apm calculations
pda_power: add suspend/resume support
power_supply: add few more values and props
pda_power: only register available psu
power: fix incorrect unregistration in power_supply_create_attrs error path
power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL
[BATTERY] power_supply_leds: use kasprintf
[BATTERY] Every file should include the headers containing the prototypes for its global functions.
* 'for-linus' of git://linux-nfs.org/~bfields/linux: (100 commits)
SUNRPC: RPC program information is stored in unsigned integers
SUNRPC: Move exported symbol definitions after function declaration part 2
NLM: tear down RPC clients in nlm_shutdown_hosts
SUNRPC: spin svc_rqst initialization to its own function
nfsd: more careful input validation in nfsctl write methods
lockd: minor log message fix
knfsd: don't bother mapping putrootfh enoent to eperm
rdma: makefile
rdma: ONCRPC RDMA protocol marshalling
rdma: SVCRDMA sendto
rdma: SVCRDMA recvfrom
rdma: SVCRDMA Core Transport Services
rdma: SVCRDMA Transport Module
rdma: SVCRMDA Header File
svc: Add svc_xprt_names service to replace svc_sock_names
knfsd: Support adding transports by writing portlist file
svc: Add svc API that queries for a transport instance
svc: Add /proc/sys/sunrpc/transport files
svc: Add transport hdr size for defer/revisit
svc: Move the xprt independent code to the svc_xprt.c file
...
* 'suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (38 commits)
suspend: cleanup reference to swsusp_pg_dir[]
PM: Remove obsolete /sys/devices/.../power/state docs
Hibernation: Invoke suspend notifications after console switch
Suspend: Invoke suspend notifications after console switch
Suspend: Clean up suspend_64.c
Suspend: Add config option to disable the freezer if architecture wants that
ACPI: Print message before calling _PTS
ACPI hibernation: Call _PTS before suspending devices
Hibernation: Introduce begin() and end() callbacks
ACPI suspend: Call _PTS before suspending devices
ACPI: Separate disabling of GPEs from _PTS
ACPI: Separate invocations of _GTS and _BFS from _PTS and _WAK
Suspend: Introduce begin() and end() callbacks
suspend: fix ia64 allmodconfig build
ACPI: clear GPE earily in resume to avoid warning
Suspend: Clean up Kconfig (V2)
Hibernation: Clean up Kconfig (V2)
Hibernation: Update messages
Suspend: Use common prefix in messages
Hibernation: Remove unnecessary variable declaration
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
PCI: make pci_bus a struct device
PCI: fix codingstyle issues in include/linux/pci.h
PCI: fix codingstyle issues in drivers/pci/pci.h
PCI: PCIE ASPM support
PCI: Fix fakephp deadlock
PCI: modify SB700 SATA MSI quirk
PCI: Run ACPI _OSC method on root bridges only
PCI ACPI: AER driver should only register PCIe devices with _OSC
PCI ACPI: Added a function to register _OSC with only PCIe devices.
PCI: constify function pointer tables
PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
pciehp: block new requests from the device before power off
pciehp: workaround against Bad DLLP during power off
pciehp: wait for 1000ms before LED operation after power off
PCI: Remove pci_enable_device_bars() from documentation
PCI: Remove pci_enable_device_bars()
PCI: Remove users of pci_enable_device_bars()
PCI: Add pci_enable_device_{io,mem} intefaces
PCI: avoid save the same type of cap multiple times
PCI: correctly initialize a structure for pcie_save_pcix_state()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (128 commits)
USB: fix codingstyle issues in drivers/usb/core/*.c
USB: fix codingstyle issues in drivers/usb/core/message.c
USB: fix codingstyle issues in drivers/usb/core/hcd-pci.c
USB: fix codingstyle issues in drivers/usb/core/devio.c
USB: fix codingstyle issues in drivers/usb/core/devices.c
USB: fix codingstyle issues in drivers/usb/core/*.h
USB: fix codingstyle issues in include/linux/usb/
USB: fix codingstyle issues in include/linux/usb.h
USB: mark USB drivers as being GPL only
USB: use a real vendor and product id for root hubs
USB: mount options: fix usbfs
USB: Fix usb_serial_driver structure for Kobil cardreader driver.
usb: ehci should use u16 for isochronous intervals
usb: ehci, remove false clear-reset path
USB: Use menuconfig objects
usb: ohci-sm501 driver
usb: dma bounce buffer support
USB: last abuses of intfdata in close for usb-serial drivers
USB: kl5kusb105 don't flush to logically disconnected devices
USB: oti6858: cleanup
...
Add LiMn (one of the most common for small non-rechargable batteries)
battery technology and voltage_min/_max properties support.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
The CAPACITY_LEVEL stuff defines various levels of charge; however, what
is the difference between them? What differentiates between HIGH and NORMAL,
LOW and CRITICAL, etc?
As it appears that these are fairly arbitrary, we end up making such policy
decisions in the kernel (or in hardware). This is the sort of decision that
should be made in userspace, not in the kernel.
If the hardware does not support _CAPACITY and it cannot be easily calculated,
then perhaps the driver should register a custom CAPACITY_LEVEL attribute;
however, userspace should not become accustomed to looking for such a thing,
and we should certainly not encourage drivers to provide CAPACITY_LEVEL
stubs.
The following removes support for POWER_SUPPLY_PROP_CAPACITY_LEVEL. The
OLPC battery driver is the only driver making use of this, so it's
removed from there as well.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Introduce global hibernation callback .end() and rename global
hibernation callback .start() to .begin(), in analogy with the
recent modifications of the global suspend callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The execution of ACPI global control methods _GTS and _BFS is
currently tied to the preparation to enter a sleep state and to the
leaving of the sleep state, respectively. However, these functions
are called before disabling the nonboot CPUs and after enabling
them, respectively (in fact, on ACPI 1.0x systems the first of them
ought to be called before suspending devices), while according to the
ACPI specification, _GTS is to be executed right prior to entering
the system sleep state and _BFS is to be executed right after the
platfor firmware has returned control to the OS on wake up.
Move the execution of _GTS and _BFS to the right places.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
On ACPI systems the target state set by acpi_pm_set_target() is
reset by acpi_pm_finish(), but that need not be called if the
suspend fails. All platforms that use the .set_target() global
suspend callback are affected by analogous issues.
For this reason, we need an additional global suspend callback that
will reset the target state regardless of whether or not the suspend
is successful. Also, it is reasonable to rename the .set_target()
callback, since it will be used for a different purpose on ACPI
systems (due to ACPI 1.0x code ordering requirements).
Introduce the global suspend callback .end() to be executed at the
end of the suspend sequence and rename the .set_target() global
suspend callback to .begin().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch (as1008b) converts the PM notifier routines from inline
calls to out-of-line code. It also prevents pm_chain_head from
being created when CONFIG_PM_SLEEP isn't enabled, and EXPORTs the
notifier registration and unregistration routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Add PM_RESTORE_PREPARE and PM_POST_RESTORE notifiers to the PM core, to be used
in analogy with the existing PM_HIBERNATION_PREPARE and PM_POST_HIBERNATION
notifiers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Move the definitions of hibernation ioctls to a separate header file in
include/linux, which can be exported to the user space.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This moves the pci_bus class device to be a real struct device and at
the same time, place it in the device tree in the correct location.
Note, the old "bridge" symlink is now gone, but this was a non-standard
link and no userspace program used it. If you need to determine the
device that the bus is on, follow the standard device symlink, or walk
up the device tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state
and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function pci_osc_support_set() traverses every root bridge when
checking for _OSC support for a capability. It quits as soon as it finds a
device/bridge that doesn't support the requested capability. This won't
work for systems that have mixed PCI and PCIe bridges when checking for
PCIe features. I split this function into two -- pci_osc_support_set() and
pcie_osc_support_set(). The latter is used when only PCIe devices should be
traversed.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that all in-tree users are gone, this removes pci_enable_device_bars()
completely.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pci_enable_device_bars() interface isn't well suited to PCI
because you can't actually enable/disable BARs individually on
a device. So for example, if a device has 2 memory BARs 0 and 1,
and one of them (let's say 1) has not been successfully allocated
by the firmware or the kernel, then enabling memory decoding
shouldn't be permitted for the entire device since it will decode
whatever random address is still in that BAR 1.
So a device must be either fully enabled for IO, for Memory, or
for both. Not on a per-BAR basis.
This provides two new functions, pci_enable_device_io() and
pci_enable_device_mem() to replace pci_enable_device_bars(). The
implementation internally builds a BAR mask in order to be able
to use existing arch infrastructure.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current pci_assign_unassigned_resources() code doesn't work properly
on 32 bits platforms with 64 bits resources. The main reason is the use
of unsigned long in various places instead of resource_size_t.
This is a pre-requisite for making powerpc use the generic code instead of
its own half-useful implementation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI error recovery usually involves the PCI adapter being reset.
If the device is using MSI, the reset will cause the MSI state
to be lost; the device driver needs to restore the MSI state.
The pci_restore_msi_state() routine is currently protected
by CONFIG_PM; remove this, and also export the symbol, so
that it can be used in a modle.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vendor_compatible and device_compatible fields in struct pci_dev aren't
used anywhere, and are somewhat pointless. Assuming that these are
historical artifacts, remove them.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCIE has a mechanism to wait for Non-Posted request to complete. I think
pci_disable_device is a good place to do this.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch #if 0's the following unused global functions:
- rom.c: pci_map_rom_copy()
- rom.c: pci_remove_rom()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global pci_restore_bars() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (100 commits)
ide: move hwif_register() call out of ide_probe_port()
ide: factor out code for tuning devices from ide_probe_port()
ide: move handling of I/O resources out of ide_probe_port()
ide: make probe_hwif() return an error value
ide: use ide_remove_port_from_hwgroup in init_irq()
ide: prepare init_irq() for using ide_remove_port_from_hwgroup()
ide: factor out code removing port from hwgroup from ide_unregister()
ide: I/O resources are released too early in ide_unregister()
ide: cleanup ide_system_bus_speed()
ide: remove needless zeroing of hwgroup fields from init_irq()
ide: remove unused ide_hwgroup_t fields
ide_platform: remove struct hwif_prop
ide: remove hwif->present manipulations from hwif_init()
ide: move wait_hwif_ready() documentation in the right place
ide: fix handling of busy I/O resources in probe_hwif()
<linux/hdsmart.h> is not used by kernel code
ide: don't include <linux/hdsmart.h>
ide-floppy: cleanup header
ide: update/add my Copyrights
ide: delete filenames/versions from comments
...
This fixes a problem where the mos7720 driver will make io to a device from
which it has been logically disconnected. It does so by introducing a flag by
which the generic usb serial code can signal the subdrivers their
disconnection and appropriate locking.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various small at91_udc cleanups:
- Use generic GPIO calls, not older platform-specific ones
- Use gpio_request()/gpio_free()
- Use VERBOSE_DEBUG convention, not older VERBOSE
- Fix sparse complaint about parameter type (changed to gfp_t)
- Add missing newline to some rarely-seen debug messages
- Fix some old cleanup bugs on probe() fault paths
Also add a mechanism whereby rm9200 gpios can drive the D+ pullup
through an inverting transistor, based on a patch from Steve Birtles.
Most UDC drivers supporting a GPIO based pullup should probably have
such an option, but testing it requries such a board in hand!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Steve Birtles <arm_kernel_development@micromark.net.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch exports two statistics to userspace:
/sys/bus/usb/device/.../power/connected_duration
/sys/bus/usb/device/.../power/active_duration
connected_duration is the total time (in msec) that the device has
been connected. active_duration is the total time the device has not
been suspended. With these two statistics, tools like PowerTOP can
calculate the percentage time that a device is active, i.e. not
suspended or auto-suspended.
Users can also use the active_duration to check if a device is actually
autosuspended. Currently, they can set power/level to auto and
power/autosuspend to a positive timeout, but there's no way to know from
userspace if a device was actually autosuspended without looking at the
dmesg output. These statistics will be useful in creating an automated
userspace script to test autosuspend for USB devices.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some boards (like e.g. Tosa) invert the VBUS-detection signal:
it's low when a host is supplying VBUS, and high otherwise.
Allow specifying whether gpio_vbus value is inverted.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Given that none of the referenced header files test the proprocessor
conditional __KERNEL__, there's no point "unifdef"fing them.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a usb serial adapter is used as console, the usb serial console
driver bumps the open_count on the port struct used but doesn't attach
a real tty to it (only a fake one temporaly). If this port is opened later
using the regular character device interface, the open method won't
initialize the port, which is the expected, and will receive a brand new
tty struct created by tty layer, which will be stored in port->tty.
When the last close is issued, open_count won't be 0 because of the
console usage and the port->tty will still contain the old tty value. This
is the last ttyUSB<n> close so the allocated tty will be freed by the
tty layer. The usb_serial and usb_serial_port are still in use by the
console, so port_free() won't be called (serial_close() ->
usb_serial_put() -> destroy_serial() -> port_free()), so the scheduled
work (port->work, usb_serial_port_work()) will still run. And
usb_serial_port_work() does:
(...)
tty = port->tty;
if (!tty)
return;
tty_wakeup(tty);
which causes (manually copied):
Faulting instruction address: 0x6b6b6b68
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT PowerMac
Modules linked in: binfmt_misc ipv6 nfs lockd nfs_acl sunrpc dm_snapshot dm_mirror dm_mod hfsplus uinput ams input_polldev genrtc cpufreq_powersave i2c_powermac therm_adt746x snd_aoa_codec_tas snd_aoa_fabric_layout snd_aoa joydev snd_aoa_i2sbus snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_page_alloc pmac_zilog serial_core evdev ide_cd cdrom snd appletouch soundcore snd_aoa_soundbus bcm43xx firmware_class usbhid ieee80211softmac ff_memless firewire_ohci firewire_core ieee80211 ieee80211_crypt crc_itu_t sungem sungem_phy uninorth_agp agpart ssb
NIP: 6b6b6b68 LR: c01b2108 CTR: 6b6b6b6b
REGS: c106de80 TRAP: 0400 Not tainted (2.6.24-rc2)
MSR: 40009032 <EE,ME,IR,DR> CR: 82004024 XER: 00000000
TASK = c106b4c0[5] 'events/0' THREAD: c106c000
GPR00: 6b6b6b6b c106df30 c106b4c0 c2d613a0 00009032 00000001 00001a00 00000001
GPR08: 00000008 00000000 00000000 c106c000 42004028 00000000 016ffbe0 0171a724
GPR16: 016ffcf4 00240e24 00240e70 016fee68 016ff9a4 c03046c4 c0327f50 c03046fc
GPR24: c106b6b9 c106b4c0 c101d610 c106c000 c02160fc c1eac1dc c2d613ac c2d613a0
NIP [6b6b6b68] 0x6b6b6b68
LR [c01b2108] tty_wakeup+0x6c/0x9c
Call Trace:
[c106df30] [c01b20e8] tty_wakeup+0x4c/0x9c (unreliable)
[c106df40] [c0216138] usb_serial_port_work+0x3c/0x78
[c106df50] [c00432e8] run_workqueue+0xc4/0x15c
[c106df90] [c0043798] worker_thread+0xa0/0x124
[c106dfd0] [c0048224] kthread+0x48/0x84
[c106dff0] [c00129bc] kernel_thread+0x44/0x60
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
Slab corruption: size-2048 start=c2d613a0, len=2048
Redzone: 0x9f911029d74e35b/0x9f911029d74e35b.
Last user: [<c01b16d8>](release_one_tty+0xbc/0xf4)
050: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
Prev obj: start=c2d60b88, len=2048
Redzone: 0x9f911029d74e35b/0x9f911029d74e35b.
Last user: [<c00f30ec>](show_stat+0x410/0x428)
000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b
This patch avoids this, clearing port->tty considering if the port is
used as serial console or not
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
G_PRINTER: Adds a USB printer gadget driver for use in printer firmware.
This adds a USB printer gadget driver for use in printer firmware.
The printer gadget channels data between the USB host and a userspace
program driving the print engine. The user space program reads and
writes the device file /dev/g_printer to receive or send printer data.
It can use ioctl calls to the device file to get or set printer status.
Signed-off-by: Craig W. Nadler <craig@nadler.us>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1011) adds a #define for the newly-created Lockable
(i.e., password-protected) subclass 0x07 for USB mass-storage devices.
The private ISD200 entry (which had been mapped to subclass 0x07) is
moved to 0xf0, which is unlikely to conflict with any official
subclass designation.
The US_SC_MIN and US_SC_MAX constants aren't used anywhere, so the
patch removes them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert from class_device to device for drivers/usb/core.
Signed-off-by: Tony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Make ide_build_sglist() and ide_destroy_dmatable() available also when
CONFIG_BLK_DEV_IDEDMA_PCI=n.
* Use ide_build_sglist() and ide_destroy_dmatable() in {ics,au1xxx-}ide.c
and remove no longer needed {ics,au}ide_build_sglist().
There should be no functionality changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
