"ath5k: remove stale function declarations, make some functions static"
commented-out some unused functions. This removes them.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Remove all unnecessary function declarations from ath5k.h. Comment out
unused functions. Remove ath5k_hw_get_tsf32(), which is too trivial to
be commented out. Make functions static if suggested by sparse. Make
ath5k_pm_ops static.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon sent gating doesn't seem to work with any combination
of flags. Thus, buffered frames tend to stay buffered forever,
using up tx descriptors.
Instead, use the DBA gating and hold transmission of the buffered
frames until 80% of the beacon interval has elapsed using the ready
time. This fixes the following error in AP mode:
ath5k phy0: no further txbuf available, dropping packet
Add a comment to acknowledge that this isn't the best solution.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code was correct in 802.11a mode only, 802.11b/g uses
different clock rates. The new code uses values taken from FreeBSD HAL
and should be correct for all modes including turbo modes.
The former rate calculation was used by slope coefficient calculation
function ath5k_hw_write_ofdm_timings. However, this function requires
the 802.11a values even in 802.11g mode. Thus the use of
ath5k_hw_htoclock was replaced by hardcoded values. Possibly the slope
coefficient calculation is not related to clock rate at all.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Functions ath5k_hw_get_slot_time and ath5k_hw_set_slot_time were
converting microseconds to clocks only for AR5210, although it's needed
for all supported devices. The conversion was moved outside the
hardware-specific branches.
The original code also limited minimum slot time to 9, while turbo modes
use 6, this was fixed too.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Elsewhere, the tqi_type field is compared to constants having a name
beginning with AR5K_TX_QUEUE, rather than AR5K_TX_QUEUE_ID. I have thus
converted AR5K_TX_QUEUE_ID_CAB to AR5K_TX_QUEUE_CAB. This does, however,
change the value, so perhaps something else was wanted.
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable the "Content" After Beacon queue and utilize it to send
any buffered frames for power-saving clients.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Write next beacon timer even on AP mode since without this we get
no beacons + ath9k does it too. Docs say that we must write 0 on
this register on AP mode to start TSF increment, we do both to be
on the safe side.
* Fix num_tx_pending function, we never read the register :P that's
why we got all those "beacon queue 7 didn't stop messages".
* Put full prioriy on beacon queue, lock all queues with lower
priority using the arblock and also bypass any arblock by seting
the arblock ignore flag.
* For the CAB queue (do we need this thing ?, it seems crap) since
it's supposed to fire up after each beacon (we don't use it on driver
part, ath9k/MadWiFi does), don't make it DBA gated but instead make
it fire after each beacon by using the beacon sent gated flag.
* Increase bmiss threshold to 10, that's what we used on MadWiFi for
a long time. Also when we have pending frames on the beacon queue (we
got a beacon that didn't make it on the air) it's more likely that
the beacon queue never started, probably due to faulty DBA setting,
so change that "beacon queue didn't stop" message.
Tested this with AP mode and IBSS mode and seems to work fine ;-)
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
