PTR_ERR(chip->tcpci) has been used as a return value,
it is not necessary to assign it to ret, so remove it.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210124143853.1630-1-angkery@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the port partner is PD2, the PDOs of the local port should follow the
format defined in PD2 Spec. Dynamically modify the pre-defined PD3 PDOs
and transform them into PD2 format before sending them to the PD2 port
partner.
Reviewed-by: Guenter Roeck <linux@roeckus.net>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210115163311.391332-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver includes the legacy GPIO header <linux/gpio.h>,
the new GPIO header <linux/gpio/consumer.h> and
the deprecated OF GPIO header <linux/of_gpio.h> yet
fail to use symbols from any of them, so drop these
includes.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210120225045.173556-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Port partner could send PR_SWAP/DR_SWAP/VCONN_SWAP/Request just after it
enters Ready states. This will cause conficts if the port is going to
send DISC_IDENT in the Ready states of TCPM. Set a flag indicating that
the state machine is processing VDM and respond Wait messages until the
VDM state machine stops.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210114145053.1952756-4-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD3.0 Spec 6.8.1 describes how to handle Protocol Error. There are
general rules defined in Table 6-61 which regulate incoming Message
handling. If the incoming Message is unexpected, unsupported, or
unrecognized, Protocol Error occurs. Follow the rules to handle these
situations. Also consider PD2.0 connection (PD2.0 Spec Table 6-36) for
backward compatibilities.
To know the types of AMS in all the recipient's states, identify those
AMS who are initiated by the port partner but not yet recorded in the
current code.
Besides, introduce a new state CHUNK_NOT_SUPP to delay the NOT_SUPPORTED
message after receiving a chunked message.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210114145053.1952756-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides the implementation of Collision Avoidance introduced
in PD3.0. The start of each Atomic Message Sequence (AMS) initiated by
the port will be denied if the current AMS is not interruptible. The
Source port will set the CC to SinkTxNG if it is going to initiate an
AMS, and SinkTxOk otherwise. Meanwhile, any AMS initiated by a Sink port
will be denied in TCPM if the port partner (Source) sets SinkTxNG except
for HARD_RESET and SOFT_RESET.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210114145053.1952756-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preventing the driver from being built-in when USB Role
Switch Class is being build as module. That fixes a
potential undefined reference error.
Fixes: 89795852c9 ("usb: typec: ucsi: Add support for USB role switch")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210119083405.18325-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI already conveys the information about a port's connection
status, whether it is operating in UFP or DFP mode, and whether the
partner supports USB data or not. This information can be used to
notify a dual-role controller to start up its host or peripheral
mode accordingly. Add optional support for this by querying each
port's fwnode to look for an associated USB role switch device.
If present, call usb_role_switch_set() with the determined data
role upon Connect Change or Connector Partner Change updates.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210111215520.18476-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generate a change uevent when the "number_of_alternate_modes" sysfs file
for partners and plugs is updated by a port driver.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Benson Leung <bleung@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20210107034904.4112029-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name of the module for the NVIDIA alt-mode is incorrect as it
looks to be a copy-paste error from the entry above, update it to
the correct typec_nvidia module name.
Cc: Ajay Gupta <ajayg@nvidia.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20210106001605.167917-1-pbrobinson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Warm reboot scenarios some times type C Mux driver gets Mux configuration
request as HPD=1,IRQ=1. In that scenario typeC Mux driver need to configure
Mux as follows as per IOM requirement:
(1). Confgiure Mux HPD = 1, IRQ = 0
(2). Configure Mux with HPD = 1, IRQ = 1
IOM expects TypeC Mux configuration as follows:
(1). HPD=1, IRQ=0
(2). HPD=1, IRQ=1
if IOM gets mux config request (2) without configuring (1), it will ignore
the request. The impact of this is there is no DP_alt mode display.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Link: https://lore.kernel.org/r/20201216140918.49197-1-madhusudanarao.amara@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace a comma between expression statements by a semicolon.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211085510.2928-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace a comma between expression statements by a semicolon.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211085553.2982-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During init, vbus_vsafe0v does not get updated till the first
connect as a sink. This causes TCPM to be stuck in SRC_ATTACH_WAIT
state while booting with a sink (For instance: a headset) connected.
[ 1.429168] Start toggling
[ 1.439907] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 1.445242] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 53.358528] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 53.358564] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
Fix this by updating vbus_vsafe0v based on vbus_present status
on boot.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201211071911.2205197-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Auto discharge circuits kick in only when vbus decays and reaches
VBUS_SINK_DISCONNECT_THRESHOLD threshold. Enable bleed discharge to
discharge vbus to VBUS_SINK_DISCONNECT_THRESHOLD upon disconnect.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201211071145.2199997-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the Type C class for plug alternate mode devices which are being
registered by the Type C connector class. This ensures that udev events
get generated when the plug alt modes are registered.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20201210211653.879044-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPM state machine needs 20-25ms to enter the ErrorRecovery state after
tPSSourceOn timer timeouts. Change the timer from max 480ms to 450ms to
ensure that the timer complies with the Spec. In order to keep the
flexibility for other usecases using tPSSourceOn, add another timer only
for PR_SWAP.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD rev3.0 8.3.3.16.3.6 PE_PRS_SRC_SNK_Wait_Source_on State
The Policy Enging Shall transition to the ErrorRecovery state when the
PSSourceOnTimer times out ...
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD 3.0 spec 8.3.3.2.3, A Get_Source_Cap message is sent
to a UUT that is in the PE_SRC_Ready state. After sending
a Source_Capabilities message, the UUT should then expect
a Request message in response. When one is not received,
the UUT should timeout to PE_SRC_Hard_Reset.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: pumahsu <pumahsu@google.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 specification chapter 3 indicates that cable data rates have to be
rounded for USB4 device to operate as USB4.
With that configure cable generation value to use rounded data rates for
USB4.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20201209042408.23079-2-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change adds vbus_vsafe0v which when set, makes TCPM
query for VSAFE0V by assigning the tcpc.is_vbus_vsafe0v callback.
Also enables ALERT.ExtendedStatus which is triggered when
status of EXTENDED_STATUS.vSafe0V changes.
EXTENDED_STATUS.vSafe0V is set when vbus is at vSafe0V and
cleared otherwise.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202040840.663578-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPM at present lacks the notion of VSAFE0V. There
are three vbus threshold levels that are critical to track:
a. vSafe5V - VBUS “5 volts” as defined by the USB
PD specification.
b. vSinkDisconnect - Threshold used for transition from
Attached.SNK to Unattached.SNK.
c. vSafe0V - VBUS “0 volts” as defined by the USB
PD specification.
Tracking vSafe0V is crucial for entry into Try.SNK and
Attached.SRC and turning vbus back on by the source in
response to hard reset.
>From "4.5.2.2.8.2 Exiting from AttachWait.SRC State" section
in the Type-C spec:
"The port shall transition to Attached.SRC when VBUS is at
vSafe0V and the SRC.Rd state is detected on exactly one of
the CC1 or CC2 pins for at least tCCDebounce."
"A DRP that strongly prefers the Sink role may optionally
transition to Try.SNK instead of Attached.SRC when VBUS
is at vSafe0V and the SRC.Rd state is detected on exactly
one of the CC1 or CC2 pins for at least tCCDebounce."
>From "7.1.5 Response to Hard Resets" section in the PD spec:
"After establishing the vSafe0V voltage condition on VBUS,
the Source Shall wait tSrcRecover before re-applying VCONN
and restoring VBUS to vSafe5V."
vbus_present in the TCPM code tracks vSafe5V(vbus_present is true)
and vSinkDisconnect(vbus_present is false).
This change adds is_vbus_vsafe0v callback which when set makes
TCPM query for vSafe0V voltage level when needed.
Since not all TCPC controllers might have the capability
to report vSafe0V, TCPM assumes that vSafe0V is same as
vSinkDisconnect when is_vbus_vsafe0v callback is not set.
This allows TCPM to continue to support controllers which don't
have the support for reporting vSafe0V.
Introducing vSafe0V helps fix the failure reported at
"Step 15. CVS verifies PUT remains in AttachWait.SRC for 500ms"
of "TD 4.7.2 Try. SNK DRP Connect DRP Test" of
"Universal Serial Bus Type-C (USB Type-C) Functional Test
Specification Chapters 4 and 5". Here the compliance tester
intentionally maintains vbus at greater than vSafe0V and expects
the Product under test to stay in AttachWait.SRC till vbus drops
to vSafe0V.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202040840.663578-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_check_send_discover does not clear the send_discover flag
when any of the following conditions are not met.
1. data_role is TYPEC_HOST
2. link is pd_capable
Discovery indentity would anyways not be attempted during
the current session anymore when the above conditions are not
met. Hence clear the send_discover flag here to prevent
tcpm_enable_frs_work from rescheduling indefinetly.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201203031908.1491542-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nRetryCount was updated from 3 to 2 between PD2.0 and PD3.0 spec.
nRetryCount in "Table 6-34 Counter parameters" of the PD 2.0
spec is set to 3, whereas, nRetryCount in "Table 6-59 Counter
parameters" is set to 2.
Pass down negotiated rev in pd_transmit so that low level chip
drivers can update the retry count accordingly before attempting
packet transmission.
This helps in passing "TEST.PD.PORT.ALL.02" of the
"Power Delivery Merged" test suite which was initially failing
with "The UUT did not retransmit the message nReryCount times"
In fusb302 & tcpci drivers, by default the driver sets the retry
count to 3 (Default for PD 2.0). Update this to 2,
if the negotiated rev is PD 3.0.
In wcove, since the retry count is intentionally set to max, leaving
it as is.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202031733.647808-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Intel PMC Mux agent driver receives the response message from PMC, it
checks for the same response bits for all the mux states.
Corrected it by checking correct response message bits, Bit 8 & 9 for the
SAFE Mode and Alternate Modes and Bit 16 & 17 for the Connect and
Disconnect Modes.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20201203220813.16281-1-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows downstream supplies and userspace to detect
whether external power is supplied.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://lore.kernel.org/r/2c8e81d9da9ff05b065f66edba915edd11f74065.1607166657.git.agx@sigxcpu.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is more in line with what tcpm does and will be needed
to avoid recursive dependency like
> drivers/power/supply/Kconfig:2:error: recursive dependency detected!
drivers/power/supply/Kconfig:2: symbol POWER_SUPPLY is selected by TYPEC_TPS6598X
drivers/usb/typec/Kconfig:64: symbol TYPEC_TPS6598X depends on REGMAP_I2C
drivers/base/regmap/Kconfig:19: symbol REGMAP_I2C is selected by CHARGER_ADP5061
drivers/power/supply/Kconfig:93: symbol CHARGER_ADP5061 depends on POWER_SUPPLY
For a resolution refer to Documentation/kbuild/kconfig-language.rst
subsection "Kconfig recursive dependency limitations"
when selecting POWER_SUPPLY.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://lore.kernel.org/r/6d11417c42d82caf66e08af160397959eb7d0d60.1607166657.git.agx@sigxcpu.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device tree property is named typec-power-opmode, not power-opmode.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201127131735.28280-1-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB Power Delivery Specification defines a set of product
types for partners and cables. The product type can be read
from the ID Header VDO which is the first object in the
response to the Discover Identity command. This attribute
will display the product type of the partner. The cables
already have the attribute.
This sysfs attribute file is only created for the partners
and cables if the product type is really known in the
driver. Some interfaces do not give access to the Discover
Identity response from the partner or cable, but they may
still supply the product type separately in some cases.
When the product type of the partner or cable is detected,
uevent is also raised with PRODUCT_TYPE set to show the
actual product type (for example PRODUCT_TYPE=host).
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201126115735.50529-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are never modified, so make them const to allow the compiler to
put them in read-only memory. Done with the help of coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201125162500.37228-3-rikard.falkeborn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TD.4.7.3. Try SNK DRP Connect Try.SRC DRP fails. The compliance
tester mimics being a Try.SRC USB-C port.
The failure is due to TCPM exiting SNK_TRY_WAIT_DEBOUNCE_CHECK_VBUS
when VBUS is not present eventhough when SNK.Rp is seen. Exit to
SRC_TRYWAIT from SNK_TRY_WAIT_DEBOUNCE_CHECK_VBUS only when SNK.Rp
is not seen for PD_T_TRY_CC_DEBOUNCE.
>From the spec:
The port shall then transition to Attached.SNK when the SNK.Rp state
is detected on exactly one of the CC1 or CC2 pins for at least
tTryCCDebounce and VBUS is detected. Alternatively, the port shall
transition to TryWait.SRC if SNK.Rp state is not detected for
tTryCCDebounce.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201125014804.1596719-1-badhri@google.com
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During PR_SWAP sequence, when TCPM is waiting in PR_SWAP_SNK_SRC_SOURCE_ON
for the vbus source to ramp up, TCPM would prematurely exit
PR_SWAP_SNK_SRC_SOURCE_ON and transition to SNK_UNATTACHED state when a
vbus off notification is received. This should not be the case as vbus
can still be off while in PR_SWAP_SNK_SRC_SOURCE_ON and the vbus source
has PD_T_NEWSRC to ramp up.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201125020703.1604979-1-badhri@google.com
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A PD-capable device can return up to 3 Product Type VDOs as part of its
DiscoverIdentity Response (USB PD Spec, Rev 3.0, Version 2.0, Section
6.4.4.3.1). Add sysfs attributes to expose these to userspace.
Cc: Benson Leung <bleung@chromium.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20201125084911.1077462-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit to introduce the num_altmodes attribute for partner had an
error where one of the parameters was named differently in the comment
and the function signature. Fix the version in the comment to align with
what is in the function signature.
This fixes the following htmldocs warning:
drivers/usb/typec/class.c:632: warning: Excess function parameter 'num_alt_modes' description in 'typec_partner_set_num_altmodes'
Fixes: a0ccdc4a77 ("usb: typec: Add number of altmodes partner attr")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20201120063523.4159877-1-pmalani@chromium.org
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a field to the typec_plug struct to record the number of available
altmodes as well as the corresponding sysfs attribute to expose this to
userspace.
This allows userspace to determine whether there are any
remaining alternate modes left to be registered by the kernel driver. It
can begin executing any policy state machine after all available
alternate modes have been registered with the connector class framework.
This value is set to "-1" initially, signifying that a valid number of
alternate modes haven't been set for the plug. The sysfs file remains
hidden as long as the attribute value is -1.
We re-use the partner attribute for number_of_alternate_modes since the
usage and name is similar, and update the corresponding *_show() command
to support both partner and plugs.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201116201150.2919178-4-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New smatch warnings:
drivers/usb/typec/tcpm/tcpci_maxim.c:324 max_tcpci_irq() error: uninitialized symbol 'irq_return'.
drivers/usb/typec/tcpm/tcpci_maxim.c:407 max_tcpci_probe() warn: passing zero to 'PTR_ERR'
The change fixes the above warnings by initializing irq_return
and replacing IS_ERR_OR_NULL with IS_ERR.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-11-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vImplement callbacks for enabling/disabling
POWER_CONTROL.AutoDischargeDisconnect.
Programs VBUS_SINK_DISCONNECT_THRESHOLD based on the
voltage requested as sink, mode of operation.
The programmed threshold is based on vSinkDisconnect and
vSinkDisconnectPD values.
Add auto_discharge_disconnect to tdata to allow TCPC chip
level drivers enable AutoDischargeDisconnect.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-9-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPCI spec allows TCPC hardware to autonomously discharge the vbus
capacitance upon disconnect. The expectation is that the TCPM enables
AutoDischargeDisconnect while entering SNK/SRC_ATTACHED states. Hardware
then automously discharges vbus when the vbus falls below a certain
threshold i.e. VBUS_SINK_DISCONNECT_THRESHOLD.
Apart from enabling the vbus discharge circuit, AutoDischargeDisconnect
is also used a flag to move TCPCI based TCPC implementations into
Attached.Snk/Attached.Src state as mentioned in
Figure 4-15. TCPC State Diagram before a Connection of the
USB Type-C Port Controller Interface Specification.
In such TCPC implementations, setting AutoDischargeDisconnect would
prevent TCPC into entering "Connection_Invalid" state as well.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-8-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally, POWER_STATUS.sourcing_vbus takes a while to clear after
writing to MAX_BUCK_BOOST_OP register. This causes vbus to turn back
on while disconnecting the sink. Overcome this issue by writing into
MAX_BUCK_BOOST_OP during frs while sourcing vbu, instead of always
into the register whenever POWER_STATUS.sourcing_vbus is set.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-7-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During FRS hardware autonomously starts to source vbus. Provide
callback to perform chip specific operations.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-6-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During FRS hardware autonomously starts to source vbus. Provide
callback to perform chip specific operations.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-5-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New source's current capability is now defined as string based
device tree property through new-source-frs-typec-current.
Refactor tcpm code to parse new-source-frs-typec-current and
infer local port's new source current capability during frs.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-4-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a user-visible attribute for the number of alternate modes available
in a partner. This allows userspace to determine whether there are any
remaining alternate modes left to be registered by the kernel driver. It
can begin executing any policy state machine after all available
alternate modes have been registered with the connector class framework.
This value is set to "-1" initially, signifying that a valid number of
alternate modes haven't been set for the partner.
Also add a sysfs file which exposes this attribute. The file remains
hidden as long as the attribute value is -1.
Cc: Benson Leung <bleung@chromium.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201116201150.2919178-3-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt cable generation bits received as a part of Thunderbolt 3 cable
discover mode VDO needs to be configured for Thunderbolt rounded and
non-rounded cable support in the Thunderbolt alternate mode.
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
--
Changes in v2:
- No change.
--
Link: https://lore.kernel.org/r/20201113202503.6559-4-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
