global_lock is defined as an unsigned long and accessing only its lower
32 bits from sysfs is incorrect, as we need to consider other 32 bits
for big endian 64-bit systems. There are no such platforms yet, but the
code needs to be robust for such a case.
Fix that by changing type of 'global_lock' to u32.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IRQ controllers and timers are the two types of device the kernel
requires before being able to use the device driver model.
ACPI so far lacks a proper probing infrastructure similar to the one
we have with DT, where we're able to declare IRQ chips and
clocksources inside the driver code, and let the core code pick it up
and call us back on a match. This leads to all kind of really ugly
hacks all over the arm64 code and even in the ACPI layer.
In order to allow some basic probing based on the ACPI tables,
introduce "struct acpi_probe_entry" which contains just enough
data and callbacks to match a table, an optional subtable, and
call a probe function. A driver can, at build time, register itself
and expect being called if the right entry exists in the ACPI
table.
A acpi_probe_device_table() is provided, taking an identifier for
a set of acpi_prove_entries, and iterating over the registered
entries.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now we have dedicated interface acpi_penalize_sci_irq() to penalize
ISA IRQ used by ACPI SCI, so remove duplicated code to penalize ACPI SCI
in acpi_irq_penalty_init().
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Avoid IRQs occupied by ISA IRQs when allocating IRQs for PCI link devices,
otherwise it may cause interrupt storm due to incompatible pin attributes.
This issue was triggered on a KVM virtual machine, which
1) uses IRQ9 for SCI in high level mode.
2) defines an PCI interrupt link device (LNKS) with IRQ9 as the only
possible irq.
3) has an PCI device referring to link device LNKS.
So it causes interrupt storm when enabling the PCI device because PCI IRQ
works in low level mode.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In acpi_ec_guard_event(), EC transaction state machine variables should be
checked with the EC spinlock locked.
The bug doesn't trigger any real issue now because this bug can only occur
when the ec_event_clearing=event mode is applied while there is no user
currently using this mode.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
1. acpi_ec_remove_query_handlers()
This patch refines the query handler removal logic implemented in
acpi_ec_remove_query_handler(), making it to invoke new
acpi_ec_remove_query_handlers() API, and ensuring all other removal code
paths to invoke the new API to honor the reference count of the query
handlers.
2. acpi_ec_get_query_handler_by_value()
This patch also refines the query handler search logic originally
implemented in acpi_ec_query(), collecting it into
acpi_ec_get_query_handler_by_value(). And since schedule_work() can ensure
the serilization of acpi_ec_event_handler(), we needn't put the
mutex_lock() around schedule_work().
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When query handler is not found, "result" is actually stil 0, and
"struct acpi_ec_query" is not NULL, so the deletion code of
"struct acpi_ec_query" at the end of the function cannot be invoked.
As a consequence, memory leak can be observed.
The issue is introduced by this commit:
Commit: 02b771b64b
Subject: ACPI / EC: Fix an issue caused by the serialized _Qxx
This patch fixes such memory leakage.
Fixes: 02b771b64b (ACPI / EC: Fix an issue caused by the serialized _Qxx evaluations)
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This commit removes all CONFIG_.*{,_MODULE} in ACPI code, replacing it
with IS_ENABLED().
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch changes the type of the return value of the acpi_sleep_proc_init()
method to be void, as this method never fails and its return value is never
used.
Signed-off-by: Rami Rosen <ramirose@gmail.com>\
[ rjw : Fixed up the static inline stub ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch changes the type of the return value of the init_acpi_device_notify()
method to be void, as this method never fails and its return value is never
used.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Empirically, acpi_add_id is mostly called with string literals, so
using kstrdup_const for initializing struct acpi_hardware_id::id saves
a little run-time memory and a string copy.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is preparation for using kstrdup_const to initialize that member.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
One wouldn't expect a "match" function modify the string it searches
for, and indeed the only instance of the struct
acpi_scan_handler::match callback, acpi_pnp_match, can easily be
changed. While there, update its helper matching_id().
This is also preparation for constifying struct acpi_hardware_id::id.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds the missing CONFIG_ prefix to INTEL_SOC_DTS_THERMAL
macros.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make device_get_next_child_node() work with ACPI data-only subnodes
introduced previously.
Namely, replace acpi_get_next_child() with acpi_get_next_subnode()
that can handle (and return) child device objects as well as child
data-only subnodes of the given device and modify the ACPI part
of the GPIO subsystem to handle data-only subnodes returned by it.
To that end, introduce acpi_node_get_gpiod() taking a struct
fwnode_handle pointer as the first argument. That argument may
point to an ACPI device object as well as to a data-only subnode
and the function should do the right thing (ie. look for the matching
GPIO descriptor correctly) in either case.
Next, modify fwnode_get_named_gpiod() to use acpi_node_get_gpiod()
instead of acpi_get_gpiod_by_index() which automatically causes
devm_get_gpiod_from_child() to work with ACPI data-only subnodes
that may be returned by device_get_next_child_node() which in turn
is required by the users of that function (the gpio_keys_polled
and gpio-leds drivers).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Modify is_acpi_node() to return "true" for ACPI data-only subnodes as
well as for ACPI device objects and change the name of to_acpi_node()
to to_acpi_device_node() so it is clear that it covers ACPI device
objects only. Accordingly, introduce to_acpi_data_node() to cover
data-only subnodes in an analogous way.
With that, make the fwnode_property_* family of functions work with
ACPI data-only subnodes introduced previously.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add infrastructure needed to expose data-only subnodes of ACPI
device objects introduced previously via sysfs.
Each data-only subnode is represented as a sysfs directory under
the directory corresponding to its parent object (a device or a
data-only subnode). Each of them has a "path" attribute (containing
the full ACPI namespace path to the object the subnode data come from)
at this time.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In some cases, the information expressed via device properties is
hierarchical by nature. For example, the properties of a composite
device consisting of multiple semi-dependent components may need
to be represented in the form of a tree of property data sets
corresponding to specific components of the device.
Unfortunately, using ACPI device objects for this purpose turns out
to be problematic, mostly due to the assumption made by some operating
systems (that platform firmware generally needs to work with) that
each device object in the ACPI namespace represents a device requiring
a separate driver. That assumption leads to complications which
reportedly are impractically difficult to overcome and a different
approach is needed for the sake of interoperability.
The approach implemented here is based on extending _DSD via pointers
(links) to additional ACPI objects returning data packages formatted
in accordance with the _DSD formatting rules defined by Section 6.2.5
of ACPI 6. Those additional objects are referred to as data-only
subnodes of the device object containing the _DSD pointing to them.
The links to them need to be located in a separate section of the
_DSD data package following UUID dbb8e3e6-5886-4ba6-8795-1319f52a966b
referred to as the Hierarchical Data Extension UUID as defined in [1].
Each of them is represented by a package of two strings. The first
string in that package (the key) is regarded as the name of the
data-only subnode pointed to by the link. The second string in it
(the target) is expected to hold the ACPI namespace path (possibly
utilizing the usual ACPI namespace search rules) of an ACPI object
evaluating to a data package extending the _DSD.
The device properties initialization code follows those links,
creates a struct acpi_data_node object for each of them to store
the data returned by the ACPI object pointed to by it and processes
those data recursively (which may lead to the creation of more
struct acpi_data_node objects if the returned data package contains
the Hierarchical Data Extension UUID section with more links in it).
All of the struct acpi_data_node objects are present until the the
ACPI device object containing the _DSD with links to them is deleted
and they are deleted along with that object.
[1]: http://www.uefi.org/sites/default/files/resources/_DSD-hierarchical-data-extension-UUID-v1.pdf
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Move the extraction of _DSD properties from acpi_init_properties()
to a separate routine called acpi_extract_properties() to make the
subsequent changes more straightforward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the ACPI APEI firmware handles hardware error first (called
"firmware first handling"), the firmware updates the GHES memory
region with hardware error record (called "generic hardware
error record"). Essentially the firmware writes hardware error
records in the GHES memory region, triggers an NMI/interrupt,
then the GHES driver goes off and grabs the error record from
the GHES region.
The kernel currently maps the GHES memory region as cacheable
(PAGE_KERNEL) for all architectures. However, on some arm64
platforms, there is a mismatch between how the kernel maps the
GHES region (PAGE_KERNEL) and how the firmware maps it
(EFI_MEMORY_UC, ie. uncacheable), leading to the possibility of
the kernel GHES driver reading stale data from the cache when it
receives the interrupt.
With stale data being read, the kernel is unaware there is new
hardware error to be handled when there actually is; this may
lead to further damage in various scenarios, such as error
propagation caused data corruption. If uncorrected error (such
as double bit ECC error) happened in memory operation and if the
kernel is unaware of such an event happening, errorneous data may
be propagated to the disk.
Instead GHES memory region should be mapped with page protection
type according to what is returned from arch_apei_get_mem_attribute().
Signed-off-by: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
[ Small stylistic tweaks. ]
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1441372302-23242-3-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull thermal updates from Zhang Rui:
- use int instead of unsigned long to represent temperature to avoid
bogus overheat detection when negative temperature reported. From
Sascha Hauer.
- export available thermal governors information to user space via
sysfs. From Wei Ni.
- introduce new thermal driver for Wildcat Point platform controller
hub, which uses PCH thermal sensor and associated critical and hot
trip points. From Tushar Dave.
- add suuport for Intel Skylake and Denlow platforms in powerclamp
driver.
- some small cleanups in thermal core.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add Intel PCH thermal driver
thermal: Add comment explaining test for critical temperature
thermal: Use IS_ENABLED instead of #ifdef
thermal: remove unnecessary call to thermal_zone_device_set_polling
thermal: trivial: fix typo in comment
thermal: consistently use int for temperatures
thermal: add available policies sysfs attribute
thermal/powerclamp: add cpu id for denlow platform
thermal/powerclamp: add cpu id for Skylake u/y
thermal/powerclamp: add cpu id for skylake h/s
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlXoqLgACgkQIXnXXONXEReNCwCghq2EtqGYTvLhupB4bJFCdtA5
ZJMAoIJ+1WIbvGJmBZ/RxehiCl/FjxTl
=+N3y
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.3' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Most of these have been sitting in linux-next for more than a release,
particularly commit 0fbcf4af7c ("ipmi: Convert the IPMI SI ACPI
handling to a platform device") which is probably the most complex
patch.
That is also the one that changes drivers/acpi/acpi_pnp.c. The change
in that file is only removing IPMI from a "special platform devices"
list, since I convert it to the standard PNP interface. I posted this
one to the ACPI list twice and got no response, and it seems to work
well in my testing, so I'm hoping it's good.
Hidehiro Kawai posted a set of changes that improves the panic time
handling in the IPMI driver.
The rest of the changes are minor bug fixes or cleanups and some
documentation"
* tag 'for-linus-4.3' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi:ssif: Add a module parm to specify that SMBus alerts don't work
ipmi: add of_device_id in MODULE_DEVICE_TABLE
ipmi: Compensate for BMCs that wont set the irq enable bit
ipmi: Don't call receive handler in the panic context
ipmi: Avoid touching possible corrupted lists in the panic context
ipmi: Don't flush messages in sender() in run-to-completion mode
ipmi: Factor out message flushing procedure
ipmi: Remove unneeded set_run_to_completion call
ipmi: Make some data const that was only read
ipmi: constify SSIF ACPI device ids
ipmi: Delete an unnecessary check before the function call "cleanup_one_si"
char:ipmi - Change 1 to true for bool type variables during initialization.
impi:Remove unneeded setting of module owner to THIS_MODULE in the platform structure, powernv_ipmi_driver
ipmi: Add a comment in how messages are delivered from the lower layer
ipmi/powernv: Fix potential invalid pointer dereference
ipmi: Convert the IPMI SI ACPI handling to a platform device
ipmi: Add device tree bindings information
1/ Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map. This facility is used by the pmem driver to
enable pfn_to_page() operations on the page frames returned by DAX
('direct_access' in 'struct block_device_operations'). For now, the
'memmap' allocation for these "device" pages comes from "System
RAM". Support for allocating the memmap from device memory will
arrive in a later kernel.
2/ Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3. Completion of
the conversion is targeted for v4.4.
3/ Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
4/ Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
5/ Miscellaneous updates and fixes to libnvdimm including support
for issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o57/
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
The IPMI SI driver was using direct PNP, but that was not really
ideal because the IPMI device is a platform device. There was
some special handling in the acpi_pnp.c code for making this work,
but that was breaking ACPI handling for the IPMI SSIF driver.
So without this patch there were significant issues getting the
SSIF driver to work with ACPI.
So use a platform device for ACPI detection and remove the
entry from acpi_pnp.c.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore,
Lv Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to
AML method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool
to be built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future
introduction of CPPC support and ACPI PCC mailbox driver
updates (Ashwin Chaugule).
- ACPI interrupts enumeration fix for a regression related
to the handling of IRQ attribute conflicts between MADT
and the ACPI namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael
J Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups
(Pan Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it
to preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support
for them in the OPP framework and in the cpufreq-dt driver plus
related OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=fTgI
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"From the number of commits perspective, the biggest items are ACPICA
and cpufreq changes with the latter taking the lead (over 50 commits).
On the cpufreq front, there are many cleanups and minor fixes in the
core and governors, driver updates etc. We also have a new cpufreq
driver for Mediatek MT8173 chips.
ACPICA mostly updates its debug infrastructure and adds a number of
fixes and cleanups for a good measure.
The Operating Performance Points (OPP) framework is updated with new
DT bindings and support for them among other things.
We have a few updates of the generic power domains framework and a
reorganization of the ACPI device enumeration code and bus type
operations.
And a lot of fixes and cleanups all over.
Included is one branch from the MFD tree as it contains some
PM-related driver core and ACPI PM changes a few other commits are
based on.
Specifics:
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore, Lv
Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to AML
method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool to be
built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future introduction
of CPPC support and ACPI PCC mailbox driver updates (Ashwin
Chaugule).
- ACPI interrupts enumeration fix for a regression related to the
handling of IRQ attribute conflicts between MADT and the ACPI
namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi
Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael J
Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan
Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it to
preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support for
them in the OPP framework and in the cpufreq-dt driver plus related
OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu)"
* tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits)
cpufreq: speedstep-lib: Use monotonic clock
cpufreq: powernv: Increase the verbosity of OCC console messages
cpufreq: sfi: use kmemdup rather than duplicating its implementation
cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
cpufreq: remove redundant 'policy' field from user_policy
cpufreq: remove redundant 'governor' field from user_policy
cpufreq: update user_policy.* on success
cpufreq: use memcpy() to copy policy
cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
cpufreq: mediatek: Add MT8173 cpufreq driver
dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
PM / Domains: Fix typo in description of genpd_dev_pm_detach()
PM / Domains: Remove unusable governor dummies
PM / Domains: Make pm_genpd_init() available to modules
PM / domains: Align column headers and data in pm_genpd_summary output
powercap / RAPL: disable the 2nd power limit properly
tools: cpupower: Fix error when running cpupower monitor
PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
PM / OPP: Fix static checker warning (broken 64bit big endian systems)
...
* pm-cpufreq: (53 commits)
cpufreq: speedstep-lib: Use monotonic clock
cpufreq: powernv: Increase the verbosity of OCC console messages
cpufreq: sfi: use kmemdup rather than duplicating its implementation
cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
cpufreq: remove redundant 'policy' field from user_policy
cpufreq: remove redundant 'governor' field from user_policy
cpufreq: update user_policy.* on success
cpufreq: use memcpy() to copy policy
cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
cpufreq: mediatek: Add MT8173 cpufreq driver
dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
intel_pstate: append more Oracle OEM table id to vendor bypass list
intel_pstate: Add SKY-S support
intel_pstate: Fix possible overflow complained by Coverity
cpufreq: Correct a freq check in cpufreq_set_policy()
cpufreq: Lock CPU online/offline in cpufreq_register_driver()
cpufreq: Replace recover_policy with new_policy in cpufreq_online()
cpufreq: Separate CPU device registration from CPU online
cpufreq: powernv: Restore cpu frequency to policy->cur on unthrottling
...
What's being done from CPUFREQ_INCOMPATIBLE, can also be done with
CPUFREQ_ADJUST. There is nothing special with CPUFREQ_INCOMPATIBLE
notifier.
Kill CPUFREQ_INCOMPATIBLE and fix its usage sites.
This also updates the numbering of notifier events to remove holes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* device-properties:
device property: check fwnode type in to_of_node()
device property: attach 'else if' to the proper 'if'
device property: fallback to pset when gettng one string
device property: fix potential NULL pointer dereference
* acpi-pm:
ACPI / bus: Move duplicate code to a separate new function
mfd: Add support for Intel Sunrisepoint LPSS devices
dmaengine: add a driver for Intel integrated DMA 64-bit
mfd: make mfd_remove_devices() iterate in reverse order
driver core: implement device_for_each_child_reverse()
klist: implement klist_prev()
Driver core: wakeup the parent device before trying probe
ACPI / PM: Attach ACPI power domain only once
PM / QoS: Make it possible to expose device latency tolerance to userspace
ACPI / PM: Update the copyright notice and description of power.c
* acpica: (42 commits)
ACPICA: Update version to 20150818
ACPICA: Debugger: Cleanup debugging outputs to dump name path without trailing underscores
ACPICA: Disassembler: Cleanup acpi_gbl_db_opt_verbose acpiexec usage
ACPICA: Disassembler: Cleanup acpi_gbl_db_opt_disasm
ACPICA: Debugger: Split debugger initialization/termination APIs
ACPICA: Header support to improve compatibility with MSVC
ACPICA: Make the max-number-of-loops runtime configurable
ACPICA: Debugger: Add option to display namespace summary/counts
ACPICA: Add additional debug info/statements
ACPICA: Table handling: Cleanup and update debug output for tools
ACPICA: acpiexec/acpinames: Support very large number of ACPI tables
ACPICA: acpinames: Add new options and wildcard support
ACPICA: Headers: Fix some comments, no functional change
ACPICA: Tables: Cleanup to reduce FACS globals
ACPICA: Tables: Fix global table list issues by removing fixed table indexes
ACPICA: Update info messages during ACPICA init
ACPICA: Disassembler: Update for new listing mode
ACPICA: Update parameter validation for data_table_region and load_table
ACPICA: Disassembler: Remove duplicate code in _PLD processing.
ACPICA: Correctly cleanup after a ACPI table load failure
...
and the addition of new clock drivers. Stephen Boyd has also done a lot
of subsystem-wide driver clean-ups (thanks!). There are also fixes to
the framework core and changes to better split clock provider drivers
from clock consumer drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QAiQ
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The clk framework changes for 4.3 are mostly updates to existing
drivers and the addition of new clock drivers. Stephen Boyd has also
done a lot of subsystem-wide driver clean-ups (thanks!). There are
also fixes to the framework core and changes to better split clock
provider drivers from clock consumer drivers"
* tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
clk: s5pv210: add missing call to samsung_clk_of_add_provider()
clk: pistachio: correct critical clock list
clk: pistachio: Fix PLL rate calculation in integer mode
clk: pistachio: Fix override of clk-pll settings from boot loader
clk: pistachio: Fix 32bit integer overflows
clk: tegra: Fix some static checker problems
clk: qcom: Fix MSM8916 prng clock enable bit
clk: Add missing header for 'bool' definition to clk-conf.h
drivers/clk: appropriate __init annotation for const data
clk: rockchip: register pll mux before pll itself
clk: add bindings for the Ux500 clocks
clk/ARM: move Ux500 PRCC bases to the device tree
clk: remove duplicated code with __clk_set_parent_after
clk: Convert __clk_get_name(hw->clk) to clk_hw_get_name(hw)
clk: Constify clk_hw argument to provider APIs
clk: Hi6220: add stub clock driver
dt-bindings: clk: Hi6220: Document stub clock driver
dt-bindings: arm: Hi6220: add doc for SRAM controller
clk: atlas7: fix pll missed divide NR in fraction mode
clk: atlas7: fix bit field and its root clk for coresight_tpiu
...
Here is the big tty/serial driver update for 4.3-rc1.
Not many major things, a number of driver updates and changes, and the
8250 driver got split up a bit to make it easier to work with by moving
some functions to a new file. Full details are in the shortlog.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlXV9dQACgkQMUfUDdst+ynbVQCgs3TBU7xHE4Yci6/w0+wo27Ru
6h8An2Fm80ia5aqFrKDl67WdRMgJyEzB
=6djD
-----END PGP SIGNATURE-----
Merge tag 'tty-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty/serial driver update for 4.3-rc1.
Not many major things, a number of driver updates and changes, and the
8250 driver got split up a bit to make it easier to work with by
moving some functions to a new file. Full details are in the
shortlog.
All have been in linux-next with no reported issues"
* tag 'tty-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (90 commits)
serial: imx: save and restore context in the suspend path
serial: imx: allow waking up on RTSD
serial: imx: introduce serial_imx_enable_wakeup()
serial: imx: remove unbalanced clk_prepare
serial: 8250: move rx_running out of the bitfield
tty: serial: 8250_omap: do not use RX DMA if pause is not supported
serial:8250_dw: do not alter CTS and DCTS since AFE is enabled
tty: serial: men_z135_uart.c: Don't initialize port->lock
tty: serial: men_z135_uart.c: Fix race between IRQ and set_termios()
serial: 8250: bind to ALi Fast Infrared Controller (ALI5123)
serial: 8250: don't bind to SMSC IrCC IR port
serial: mxs-auart: fix baud rate range
serial: mxs-auart: keep the AUART unit in reset state when not in use
serial: mxs-auart: use a function name to reflect what it really does
serial: 8250_pci: fix mode after S3/S4 resume for F81504/508/512
sc16is7xx: constify devtype
sc16is7xx: support multiple devices
sc16is7xx: save and use per-chip line number
uart: pl011: Add support to ZTE ZX296702 uart
uart: pl011: Improve LCRH register access decision
...
Pull nvdimm fixlet from Dan Williams:
"This is a libnvdimm ABI fixup.
I pushed back on this change quite hard given the late date, that it
appears to be purely cosmetic, sysfs is not necessarily meant to be a
user friendly UI, and the kernel interprets the reversed polarity of
the ACPI_NFIT_MEM_ARMED flag correctly. When this flag is set, the
energy source of an NVDIMM is not armed and any new writes to the DIMM
may not be preserved.
However, Bob Moore warned me that it is important to get these things
named correctly wherever they appear otherwise we run the risk of a
less than cautious firmware engineer implementing the polarity the
wrong way. Once a mistake like that escapes into production platforms
the flag becomes useless and we need to move to a new bit position.
Bob has agreed to take a change through ACPICA to rename
ACPI_NFIT_MEM_ARMED to ACPI_NFIT_MEM_NOT_ARMED, and the patch below
from Toshi brings the sysfs representation of these flags in line with
their respective polarities.
Please pull for 4.2 as this is the first kernel to expose the ACPI
NFIT sysfs representation, and this is likely a kernel that firmware
developers will be using for checking out their NVDIMM enabling"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: Clarify memory device state flags strings
Given that a write-back (WB) mapping plus non-temporal stores is
expected to be the most efficient way to access PMEM, update the
definition of ARCH_HAS_PMEM_API to imply arch support for
WB-mapped-PMEM. This is needed as a pre-requisite for adding PMEM to
the direct map and mapping it with struct page.
The above clarification for X86_64 means that memcpy_to_pmem() is
permitted to use the non-temporal arch_memcpy_to_pmem() rather than
needlessly fall back to default_memcpy_to_pmem() when the pcommit
instruction is not available. When arch_memcpy_to_pmem() is not
guaranteed to flush writes out of cache, i.e. on older X86_32
implementations where non-temporal stores may just dirty cache,
ARCH_HAS_PMEM_API is simply disabled.
The default fall back for persistent memory handling remains. Namely,
map it with the WT (write-through) cache-type and hope for the best.
arch_has_pmem_api() is updated to only indicate whether the arch
provides the proper helpers to meet the minimum "writes are visible
outside the cache hierarchy after memcpy_to_pmem() + wmb_pmem()". Code
that cares whether wmb_pmem() actually flushes writes to pmem must now
call arch_has_wmb_pmem() directly.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
[hch: set ARCH_HAS_PMEM_API=n on x86_32]
Reviewed-by: Christoph Hellwig <hch@lst.de>
[toshi: x86_32 compile fixes]
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This should result in a pretty sizeable performance gain for reads. For
rough comparison I did some simple read testing using PMEM to compare
reads of write combining (WC) mappings vs write-back (WB). This was
done on a random lab machine.
PMEM reads from a write combining mapping:
# dd of=/dev/null if=/dev/pmem0 bs=4096 count=100000
100000+0 records in
100000+0 records out
409600000 bytes (410 MB) copied, 9.2855 s, 44.1 MB/s
PMEM reads from a write-back mapping:
# dd of=/dev/null if=/dev/pmem0 bs=4096 count=1000000
1000000+0 records in
1000000+0 records out
4096000000 bytes (4.1 GB) copied, 3.44034 s, 1.2 GB/s
To be able to safely support a write-back aperture I needed to add
support for the "read flush" _DSM flag, as outlined in the DSM spec:
http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf
This flag tells the ND BLK driver that it needs to flush the cache lines
associated with the aperture after the aperture is moved but before any
new data is read. This ensures that any stale cache lines from the
previous contents of the aperture will be discarded from the processor
cache, and the new data will be read properly from the DIMM. We know
that the cache lines are clean and will be discarded without any
writeback because either a) the previous aperture operation was a read,
and we never modified the contents of the aperture, or b) the previous
aperture operation was a write and we must have written back the dirtied
contents of the aperture to the DIMM before the I/O was completed.
In order to add support for the "read flush" flag I needed to add a
generic routine to invalidate cache lines, mmio_flush_range(). This is
protected by the ARCH_HAS_MMIO_FLUSH Kconfig variable, and is currently
only supported on x86.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ACPI 6.0 NFIT Memory Device State Flags in Table 5-129 defines
NVDIMM status as follows. These bits indicate multiple info,
such as failures, pending event, and capability.
Bit [0] set to 1 to indicate that the previous SAVE to the
Memory Device failed.
Bit [1] set to 1 to indicate that the last RESTORE from the
Memory Device failed.
Bit [2] set to 1 to indicate that platform flush of data to
Memory Device failed. As a result, the restored data content
may be inconsistent even if SAVE and RESTORE do not indicate
failure.
Bit [3] set to 1 to indicate that the Memory Device is observed
to be not armed prior to OSPM hand off. A Memory Device is
considered armed if it is able to accept persistent writes.
Bit [4] set to 1 to indicate that the Memory Device observed
SMART and health events prior to OSPM handoff.
/sys/bus/nd/devices/nmemX/nfit/flags shows this flags info.
The output strings associated with the bits are "save", "restore",
"smart", etc., which can be confusing as they may be interpreted
as positive status, i.e. save succeeded.
Change also the dev_info() message in acpi_nfit_register_dimms()
to be consistent with the sysfs flags strings.
Reported-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
[ross: rename 'not_arm' to 'not_armed']
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
[djbw: defer adding bit5, HEALTH_ENABLED, for now]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
LPSS devices in Braswell does not need the default 10ms
d3_delay imposed by PCI specification. Removing this
unnecessary delay significantly reduces the resume time
approximately upto 200ms on this platform.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Nick Meier reported a regression with HyperV that "
After rebooting the VM, the following messages are logged in syslog
when trying to load the tulip driver:
tulip: Linux Tulip drivers version 1.1.15 (Feb 27, 2007)
tulip: 0000:00:0a.0: PCI INT A: failed to register GSI
tulip: Cannot enable tulip board #0, aborting
tulip: probe of 0000:00:0a.0 failed with error -16
Errors occur in 3.19.0 kernel
Works in 3.17 kernel.
"
According to the ACPI dump file posted by Nick at
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1440072
The ACPI MADT table includes an interrupt source overridden entry for
ACPI SCI:
[236h 0566 1] Subtable Type : 02 <Interrupt Source Override>
[237h 0567 1] Length : 0A
[238h 0568 1] Bus : 00
[239h 0569 1] Source : 09
[23Ah 0570 4] Interrupt : 00000009
[23Eh 0574 2] Flags (decoded below) : 000D
Polarity : 1
Trigger Mode : 3
And in DSDT table, we have _PRT method to define PCI interrupts, which
eventually goes to:
Name (PRSA, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
Name (PRSB, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
Name (PRSC, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
Name (PRSD, ResourceTemplate ()
{
IRQ (Level, ActiveLow, Shared, )
{3,4,5,7,9,10,11,12,14,15}
})
According to the MADT and DSDT tables, IRQ 9 may be used for:
1) ACPI SCI in level, high mode
2) PCI legacy IRQ in level, low mode
So there's a conflict in polarity setting for IRQ 9.
Prior to commit cd68f6bd53 ("x86, irq, acpi: Get rid of special
handling of GSI for ACPI SCI"), ACPI SCI is handled specially and
there's no check for conflicts between ACPI SCI and PCI legagy IRQ.
And it seems that the HyperV hypervisor doesn't make use of the
polarity configuration in IOAPIC entry, so it just works.
Commit cd68f6bd53 gets rid of the specially handling of ACPI SCI,
and then the pin attribute checking code discloses the conflicts
between ACPI SCI and PCI legacy IRQ on HyperV virtual machine,
and rejects the request to assign IRQ9 to PCI devices.
So penalize legacy IRQ used by ACPI SCI and mark it unusable if ACPI
SCI attributes conflict with PCI IRQ attributes.
Please refer to following links for more information:
https://bugzilla.kernel.org/show_bug.cgi?id=101301https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1440072
Fixes: cd68f6bd53 ("x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI")
Reported-and-tested-by: Nick Meier <nmeier@microsoft.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: 3.19+ <stable@vger.kernel.org> # 3.19+
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull nvdimm fix from Dan Williams:
"A single fix for status register read size in the nd_blk driver.
The effect of getting the width of this register read wrong is that
all I/O fails when the read returns non-zero. Given the availability
of ACPI 6 NFIT enabled platforms, this could reasonably wait to come
in during the 4.3 merge window with a tag for 4.2-stable. Otherwise,
this makes the 4.2 kernel fully functional with devices that conform
to the mmio-block-apertures defined in the ACPI 6 NFIT (NVDIMM
Firmware Interface Table)"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit, nd_blk: BLK status register is only 32 bits
Obviously in the current place the 'else' keyword is redundant, though it seems
quite correct when we check if nval is in allowed range.
Reattach the condition branch there.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Only read 32 bits for the BLK status register in read_blk_stat().
The format and size of this register is defined in the
"NVDIMM Driver Writer's guide":
http://pmem.io/documents/NVDIMM_Driver_Writers_Guide.pdf
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Tested-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ACPICA commit 42d7ad7bfb1cfb95183c1386c77509f2036f521d
When acpi_gbl_db_opt_verbose is used in acpi_dm_descending_op() (invoked by
acpi_dm_disassemble()), it is actually exported by the disassembler but used
by the debugger to distinguish the output of the disassembler for different
debugger commands. It is by default TRUE but is set to FALSE for control
method disassembly command - "disassemble". So it's initialization should
be a part of the ACPI_DISASSEMBLER conditioned code. This patch uses
ACPI_INIT_GLOBAL to achieve a clean manner so that when ACPI_DISASSEMBLER
is not defined, ACPI_DEBUGGER conditioned code needn't link to this option.
Since it is a disassembler exported variable, it is renamed to
acpi_gbl_dm_opt_Verbose in this patch.
As VERBOSE_PRINT() macro has only one user, this patch also removes the
definition of this macro. Lv Zheng.
This patch doesn't affect Linux kernel.
Link: https://github.com/acpica/acpica/commit/42d7ad7b
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 969989cf7f85e2a2a0cd048cd25fc706246a48a2
This patch cleans up the following global variable - acpi_gbl_db_opt_disasm:
The setting is used to control the full disassembly feature for iasl. ACPI
debugger (acpiexec) shall have nothing to do with it. Actually, acpiexec
never links to ad_aml_disassemble().
This patch thus renames this global option to acpi_gbl_dm_opt_disasm and
removes all acpiexec and debugger references on it. Lv Zheng.
This patch doesn't affect Linux kernel.
Link: https://github.com/acpica/acpica/commit/969989cf
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7a3f22baab000b186779dac64ad71d9776b8f432
It is likely that the debugger is enabled only when a userspace program
explicitly tells a kernel to do so, so it shouldn't be initialized as
early as current implementation.
The only tool requiring ACPI_DEBUGGER is acpiexec, so acpiexec need to call
the new APIs by itself. And BSD developers may also get notified to invoke
the APIs for DDB enabling. Lv Zheng.
This patch doesn't affect Linux kernel as debugger is currently not enabled
in the Linux kernel.
Link: https://github.com/acpica/acpica/commit/7a3f22ba
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit a9d9c2d0c2d077bb3175ec9c252cf0e5da3efd45
Was previously compile-time only.
Add support option for acpiexec.
Link: https://github.com/acpica/acpica/commit/a9d9c2d0
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit bba222c15c2ce79076eb3a5e9d4d5f7120db8a00
If "Objects" command is invoked with no arguments, the counts
for each object type are displayed.
Linux kernel is not affected by this commit as currently debugger is
not enabled in the Linux kernel.
Link: https://github.com/acpica/acpica/commit/bba222c1
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 74094ca9f51e2652a9b5f01722d8640a653cc75a
For _REG methods and module-level code blocks.
For acpiexec, add deletion of module-level blocks in case
of an early abort.
Link: https://github.com/acpica/acpica/commit/74094ca9
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 93862bd7a227543bc617d822ef5c4f8a5d68b519
Add output of table OEM ID along with signature to support lots
of SSDTs.
Cleanup use of table pointers.
Link: https://github.com/acpica/acpica/commit/93862bd7
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ca3bd4c5cdc39a9009280032adbbc20f34e94c47
Fix a couple of issues with >40 ACPI tables.
Return exit error for acpinames to enable use with BIOS builds.
The new exported function is used by acpinames. For Linux kernel, this
change is a no-op.
Link: https://github.com/acpica/acpica/commit/ca3bd4c5
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 0ecf5b5a41c3d2e09af48f0fdbc9ae784f631788
- Add wilcard support for input filenames.
- Add -l option to load tables and exit, no display. This is
useful for validation of the namespace during BIOS generation.
- Add -x option for specifying debug level.
Linux kernel is not affected by this commit.
Link: https://github.com/acpica/acpica/commit/0ecf5b5a
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 3f42ba76e2a0453976d3108296d5f656fdf2bd6e
In this patch, FACS table mapping is also tuned a bit so that only the
selected FACS table will be mapped by the OSPM (mapped on demand) and the
FACS related global variables can be reduced. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/3f42ba76
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit c0b38b4c3982c2336ee92a2a14716107248bd941
The fixed table indexes leave holes in the global table list:
1. One hole can be seen when there is only 1 FACS provided by the BIOS.
2. Tow holes can be seen when it is a reduced hardware platform.
The holes do not break OSPMs but have broken ACPI debugger "tables"
command.
Also the "fixed table indexes" mechanism may make the descriptors of the
standard tables installed earlier than DSDT to be overwritten by the
descriptors of the fixed tables. For example, FACP disappears from the
global table list after DSDT is installed.
This patch fixes all above issues by removing the "fixed table indexes"
mechanism which is too complicated to be maintained in a regression safe
manner. After removal, the table loader will determine the indexes of the
fixed tables. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/c0b38b4c
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 4ccf8a1cc499ec8f00345f662a5887483980e1dd
Small cleanup of messages.
Link: https://github.com/acpica/acpica/commit/4ccf8a1c
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 2ed09bb7619d25f5a5c065c33a8a775a6db3a856
ACPICA commit 2fefacf73825b0ec96bbfc4f70a256735b715d6c
This mode emits AML code along with the ASL code.
A new global was needed to ensure the listing mode is
completely separate from the debugger verbose mode.
Emits the correct AML offset for the AML code.
The -l option now works for both the compiler and disassembler.
Linux kernel is not affected by this commit.
Link: https://github.com/acpica/acpica/commit/2fefacf7
Link: https://github.com/acpica/acpica/commit/2ed09bb7
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 51ab555e60b4a3de3cc4a846e86d0de255be441a
Add additional validation for the table signature and
the OEM strings. Eliminates buffer read overrun in data_table_region.
ACPICA BZ 1184.
Link: https://bugs.acpica.org/show_bug.cgi?id=1184
Link: https://github.com/acpica/acpica/commit/51ab555e
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ed7769e832de6c7ba90615480d916c85fd100422
If a table load fails, delete all namespace objects created by the
table, otherwise these objects will be uninitialized, causing
problems later. This appears to be a very rare problem.
Also handle the unitialized node problem to prevent possible
faults. ACPICA BZ 1185.
Link: https://github.com/acpica/acpica/commit/ed7769e8
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch introduces a new Kconfig symbol, ACPI_PROCESSOR_IDLE,
which is auto selected by architectures which support the ACPI
based C states for CPU Idle management.
The processor_idle driver in its present form contains declarations
specific to X86 and IA64. Since there are no reasonable defaults
for other architectures e.g. ARM64, the driver is selected only for
X86 or IA64.
This helps in decoupling the ACPI processor_driver from the ACPI
processor_idle driver which is useful for the upcoming alternative
patchwork for controlling CPU Performance (CPPC) and CPU Idle (LPI).
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI processor driver is currently tied too closely
to the ACPI P-states (PSS) and other related constructs
for controlling CPU performance.
The newer ACPI specification (v5.1 onwards) introduces
alternative methods to PSS. These new mechanisms are
described within each ACPI Processor object and so they
need to be scanned whenever a new Processor object is detected.
This patch introduces a new Kconfig symbol to allow for
finer configurability among the two options for controlling
performance states. There is no change in functionality and
the option is auto-selected by the architectures which support it.
A future commit will introduce support for CPPC: A newer method of
controlling CPU performance. The OS is not expected to support
CPPC and PSS at the same time, so the Kconfig option lets us make
the two mutually exclusive at compile time.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The readq() and writeq() helpers are available in the
asm-generic/io-64-nonatomic-hi-lo.h and asm-generic/io-64-nonatomic-lo-hi.h
headers. Replace custom implementation by the generic helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is proven that Windows evaluates _Qxx handlers in a parallel way. This
patch follows this fact, splits _Qxx evaluations from the NOTIFY queue to
form a separate queue, so that _Qxx evaluations can be queued up on
different CPUs rather than being queued up on a CPU0 bound queue.
Event handling related callbacks are also renamed and sorted in this patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=94411
Reported-and-tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Before this commit, the following would happen:
a) acpi_video_get_backlight_type() gets called
b) acpi_video_get_backlight_type() calls acpi_video_init_backlight_type()
c) acpi_video_init_backlight_type() locks its function static init_mutex
d) acpi_video_init_backlight_type() calls backlight_register_notifier()
e) backlight_register_notifier() takes its notifier-chain lock
And when the backlight notifier chain gets called we've:
1) blocking_notifier_call_chain() gets called
2) blocking_notifier_call_chain() takes the notifier-chain lock
3) blocking_notifier_call_chain() calls acpi_video_backlight_notify()
4) acpi_video_backlight_notify() calls acpi_video_get_backlight_type()
5) acpi_video_get_backlight_type() calls acpi_video_init_backlight_type()
6) acpi_video_init_backlight_type() locks its function static init_mutex
So in the first call sequence we have:
a) init_mutex gets locked
b) notifier-chain gets locked
and in the second call sequence we have:
1) notifier-chain gets locked
2) init_mutex gets locked
And we've a circular locking dependency. This specific locking dependency
is fixable without using the big hammer otherwise known as a workqueue,
but further analysis shows a similar problem with the backlight notifier
chain lock vs register_count_mutex from drivers/acpi/acpi_video.c,
and fixing that becomes problematic.
So this commit simply fixes this with the big hammer, performance
wise this is a non issue as we expect the work to get scheduled
exactly zero or one times during normal system use.
Fixes: 93a291dfaf (ACPI / video: Move backlight notifier to video_detect.c)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_debugfs_init function is declared with return type int in
drivers/acpi/internal.h when CONFIG_DEBUG_FS is enabled, but its
definition in drivers/acpi/debugfs.c has return type void. This is due
to commit aecad432fd ("ACPI: Cleanup custom_method debug stuff"),
which changed the return type from int to void without updating the
declaration.
Fix this inconsistency by updating acpi_debugfs_init prototype. While
at it, include internal.h in debugfs.c so that the compiler can check
that the declaration and definition remain compatible.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since _SB.PCI0 can be used as relative path from root and can be easily
converted into internal trace_method_name format, we allow users to specify
trace_method_name using relative paths from root.
Note this is useful for grub2 for which users failed to pass "\" from the
grub configuration file.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch updates the method tracing facility as the acpi_debug_trace()
API has been updated to allow it to trace AML interpreter execution, the
meanings and the usages of the API parameters are changed due to the
updates.
The new API:
1. Uses ACPI_TRACE_ENABLED flag to indicate the enabling of the tracer;
2. Allows tracer still can be enabled when method name is not specified so
that the AML interpreter execution can be traced without knowing the
method name, which is useful for kernel boot tracing;
3. Supports arbitrary full path name, it doesn't need to be a name related
to an entrance of acpi_evaluate_object().
Note that the sysfs parameters are also updated so that when reading the
attribute files, ACPICA internal settings are returned.
In order to make the sysfs parameters (acpi.trace_state) available during
boot, this patch adds code to bypass ACPICA semaphore/mutex invocations
when acpi mutex utilities haven't been initialized.
This patch doesn't update documentation of method tracing facility, it will
be updated by further patches.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After merging commit 712e960f0e (ACPI / PM: Attach ACPI power
domain only once) with commit 1dcc3d3362 (ACPI / bus: Move ACPI
bus type registration) there is some duplicate code in
acpi_device_is_first_physical_node() and acpi_companion_match()
that can be moved to a separate routine and called from both
places.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
The thermal code uses int, long and unsigned long for temperatures
in different places.
Using an unsigned type limits the thermal framework to positive
temperatures without need. Also several drivers currently will report
temperatures near UINT_MAX for temperatures below 0°C. This will probably
immediately shut the machine down due to overtemperature if started below
0°C.
'long' is 64bit on several architectures. This is not needed since INT_MAX °mC
is above the melting point of all known materials.
Consistently use a plain 'int' for temperatures throughout the thermal code and
the drivers. This only changes the places in the drivers where the temperature
is passed around as pointer, when drivers internally use another type this is
not changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Peter Feuerer <peter@piie.net>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Peter Feuerer <peter@piie.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add pci_has_managed_irq(), pci_set_managed_irq(), and
pci_reset_managed_irq() to simplify code. No functional change.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
To support IOAPIC hotplug, we need to allocate PCI IRQ resources on demand
and free them when not used anymore.
Implement pcibios_alloc_irq() and pcibios_free_irq() to dynamically
allocate and free PCI IRQs.
Remove mp_should_keep_irq(), which is no longer used.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Conflicts:
drivers/acpi/scan.c
The conflict is resolved by moving the just introduced
acpi_device_is_first_physical_node() to bus.c and using
the existing acpi_companion_match() from there.
There will be an additional commit to combine the two.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qx8r
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-base-acpi-dma-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into acpi-pm
Pull MFD-related material including ACPI device power management
changes (in addition to MFD, driver core and DMA changes) for v4.3
from Lee Jones.
* tag 'ib-mfd-base-acpi-dma-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: Add support for Intel Sunrisepoint LPSS devices
dmaengine: add a driver for Intel integrated DMA 64-bit
mfd: make mfd_remove_devices() iterate in reverse order
driver core: implement device_for_each_child_reverse()
klist: implement klist_prev()
Driver core: wakeup the parent device before trying probe
ACPI / PM: Attach ACPI power domain only once
PM / QoS: Make it possible to expose device latency tolerance to userspace
Commit 20dacb71ad ("ACPI / PM: Rework device power management to follow
ACPI 6") changed the device power management to use D3hot if the device
in question does not have _PR3 method even if D3cold was requested by the
caller.
However, if the device has _PR3 device->power.state is also set to D3hot
instead of D3Cold after power resources have been turned off because
device->power.state will be assigned from "state" instead of
"target_state".
Next time the device is transitioned to D0, acpi_power_transition() will
find that the current power state of the device is D3hot instead of D3cold
which causes it to power down all resources required for the current
(wrong) state D3hot.
Below is a simplified ASL example of a real touch panel device which
triggers the problem:
Scope (TPL1)
{
Name (_PR0, Package (1) { \_SB.PCI0.I2C1.PXTC })
Name (_PR3, Package (1) { \_SB.PCI0.I2C1.PXTC })
...
}
In both D0 and D3hot the same power resource is required. However, when
acpi_power_transition() turns off power resources required for D3hot (as
the device is transitioned to D0) it powers down PXTC which then makes the
device to lose its power.
Fix this by assigning "target_state" to the device power state instead of
"state" that is always D3hot even for devices with valid _PR3.
Fixes: 20dacb71ad (ACPI / PM: Rework device power management to follow ACPI 6)
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some devices, like MFD subdevices, share a single ACPI companion device so
that they are able to access their resources and children. However,
currently all these subdevices are attached to the ACPI power domain and
this might cause that the power methods for the companion device get called
more than once.
In order to solve this we attach the ACPI power domain only to the first
physical device that is bound to the ACPI companion device. In case of MFD
devices, this is the parent MFD device itself.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The _STA only applies to the root device, not the individual NVDIMMS,
so don't check here. NVDIMM device state flags are checked elsewhere.
Signed-off-by: Linda Knippers <linda.knippers@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add support for the three ARS DSM commands:
- Query ARS Capabilities - Queries the firmware to check if a given
range supports scrub, and if so, which type (persistent vs. volatile)
- Start ARS - Starts a scrub for a given range/type
- Query ARS Status - Checks status of a previously started scrub, and
provides the error logs if any.
The commands are described by the example DSM spec at:
http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf
Also add these commands to the nfit_test test framework, and return
canned data.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ACPICA commit add72dca18ab5d02f1bf9b08027570e58da520e8
This mode will emit AML byte code after each ASL statement.
This is a prototype only and requires additional development.
This patch only affects ACPICA disassembler which is not in the kernel
source tree.
Link: https://github.com/acpica/acpica/commit/add72dca
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 2164923d60429eea7cd5a4a8629b607af7325afa
Some disassembler APIs should rather be debugger APIs. This patch moves
them to the debugger folder to be ready for debugger porting.
Since there is no in-kernel ACPICA debugger in the kernel source tree, this
patch doesn't affect the Linux kernel.
Link: https://github.com/acpica/acpica/commit/2164923d
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 310e0ae1c4730f4dadc80125125099ab76851499
arg_types in struct acpi_db_method_info is only referenced by ACPI_DEBUGGER.
This patch only affects ACPICA debugger which is only used by a non-kernel
tool - acpiexec, so Linux kernel is currently not affected by this patch.
Link: https://github.com/acpica/acpica/commit/310e0ae1
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f88814201e01043a4f8caa69a69b799af11c44a3
These were defined in two places. Changed to ACPI_SIGN* names
and define them once in acmacros.h
This patch doesn't affect Linux kernel.
Link: https://github.com/acpica/acpica/commit/f8881420
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7c490c28a18b435c543c6b410e7e7c2131fccc78
ACPICA implements all non-ANSI functions locally. However, there
are sometimes two or more versions of the same function throughout
the ACPICA code. This change fixes this.
Adds a new file, utilities/utnonansi.c
Link: https://github.com/acpica/acpica/commit/7c490c28
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit eb9f8cb9fd65f1149dd335d05944c31cbca41af3
1) Warn if a Local is set but never used
2) Warn if a arg_x is never used (for non-predefined method names)
3) Warn if a arg_x that is used as a local is never used
This patch only affects iASL which is not in the kernel source tree.
Link: https://github.com/acpica/acpica/commit/eb9f8cb9
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f9fd6e8bad0f16ce2b436c5cda36ced0c2d85302
Reported by Markus Elfring.
Link: https://github.com/acpica/acpica/commit/f9fd6e8b
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit c832b0a9263c560b3ae3ae31d7298ef33988f8d5
This patch removes one redundant debugging output of opcode execution which
has already been covered by acpi_ex_start_trace_opcode(). Lv Zheng.
Link: https://github.com/acpica/acpica/commit/c832b0a9
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 61e9e20aadfaa03184d0959fbdc1fa5cdfea2551
This patch adds option to bypass opcode tracing. The option can be used to
reduce the trace message output. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/61e9e20a
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit e8e4a9b19d0b72a7b165398bdc961fc2f6f502ec
This patch adds OSL trace hook support.
OSPMs are encouraged to use acpi_os_trace_point() with
ACPI_USE_SYSTEM_TRACER defined to implement platform specific trace
facility. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/e8e4a9b1
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 07fffd02607685b655ed92ee15c160e6a810b60b
The acpi_debug_trace() is the mechanism known as ACPI method tracing that is
used by Linux as ACPICA debugging message reducer. This facility can be
controlled through Linux ACPI subsystem - /sys/module/acpi/parameters.
This facility requires CONFIG_ACPI_DEBUG to be enabled to see ACPICA trace
logs in the kernel dmesg output.
This patch enhances acpi_debug_trace() to make it not only a message reducer,
but a real tracer to trace AML interpreter execution. Note that in addition
to the AML tracer enabling, this patch also updates the facility with the
following enhancements:
1. Allow a full path to be specified by the acpi_debug_trace() API.
2. Allow any method rather than just the entrance of acpi_evaluate_object()
to be traced.
3. All interpreter ACPI_LV_TRACE_POINT messages are collected for
ACPI_EXECUTER layer.
The Makefile of drivers/acpi/acpica is also updated to include exdebug.o
and the duplicated stubs are removed after that.
Note that since this patch has enhanced the method tracing facility, Linux
need also be updated after applying this patch. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/07fffd02
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 71299ec8b49054daace0df50268e8e055654ca37
This patch adds trace point at the following point:
1. Begin/end of a control method execution;
2. Begin/end of an opcode execution.
The trace point feature can be enabled by defining ACPI_DEBUG_OUTPUT
and specifying a debug level that includes ACPI_LV_TRACDE_POINT and the
debug layers that include ACPI_PARSER and ACPI_DISPACTCHER.
In order to make aml_op_name of union acpi_parse_object usable for tracer, it is
enabled for ACPI_DEBUG_OUTPUT in this patch. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/71299ec8
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
