Some of the pin names were provided officially to the customers
in different spelling. We update pin names in accordance with
the official list.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5 ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812f ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Protect IO in intel_gpio_get_direction(), intel_gpio_community_irq_handler(),
intel_config_get_debounce() and intel_config_get_pull() by lock. Even for
simple readl() we better serialize IO to avoid potential problems.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Split intel_config_get() to three functions, i.e. intel_config_get() and
two helpers intel_config_get_pull() and intel_config_get_debounce() to be
symmetrical with intel_config_set*().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Drop the only label in the code, i.e. in intel_config_set_debounce(),
for consistency with the rest. In entire driver we use multipoint
return.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Instead of using bitwise operations against returned values,
which is a bit fragile, convert IRQ handler to count amount of
GPIO groups, where at least one interrupt happened, and convert
it to returned value by IRQ_RETVAL() macro.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It's possible scenario that pin has been in different mode, while
the respective GPIO register has a leftover output buffer enabled.
In such case when we request GPIO it will switch to GPIO mode, and
thus to output with unknown value, followed by switching to input
mode. This can produce a glitch on the pin.
Disable input and output buffer when switching to GPIO to avoid
potential glitches.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We have some data structures duplicated across the drivers.
Let's deduplicate them by using struct intel_pinctrl_soc_data,
struct intel_community and struct intel_pinctrl_context that
are being provided by pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Individual drivers may install ACPI OpRegion handlers based on
address space ID which differs from community to community.
Add special field in the struct intel_community for that purpose.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Change STM32 pinctrl driver to not print an error trace when probe is
deferred due to clock resource. Probe defer issue (for clocks) could
occur during bank registering when some banks have already been registered.
In this case banks already registered should be released. To not waste time
in this case, it is better to check first if all clocks are available
before registering banks.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Link: https://lore.kernel.org/r/20200615125407.27632-2-alexandre.torgue@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the correct the function name in the documentation for
"pcs_parse_one_pinctrl_entry()".
"smux_parse_one_pinctrl_entry()" appears to be an artifact from the
development of a prior patch series ("simple pinmux driver") which
transformed into pinctrl-single.
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Link: https://lore.kernel.org/r/20200612112758.GA3407886@x1
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit ba40324261.
After commit 26d8cde526 ("pinctrl: freescale: imx: add shared
input select reg support"). i.MX7D has two iomux controllers
iomuxc and iomuxc-lpsr which share select_input register for
daisy chain settings.
If use 'devm_of_iomap()', when probe the iomuxc-lpsr, will call
devm_request_mem_region() for the region <0x30330000-0x3033ffff>
for the first time. Then, next time when probe the iomuxc, API
devm_platform_ioremap_resource() will also use the API
devm_request_mem_region() for the share region <0x30330000-0x3033ffff>
again, then cause issue, log like below:
[ 0.179561] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver
[ 0.191742] imx7d-pinctrl 30330000.pinctrl: can't request region for resource [mem 0x30330000-0x3033ffff]
[ 0.191842] imx7d-pinctrl: probe of 30330000.pinctrl failed with error -16
Fixes: ba40324261 ("pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/1591673223-1680-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch causes pcs_parse_pinconf() to return -ENOTSUPP when no
pinctrl_map is added. The current behavior is to return 0 when
!PCS_HAS_PINCONF or !nconfs. Thus pcs_parse_one_pinctrl_entry()
incorrectly assumes that a map was added and sets num_maps = 2.
Analysis:
=========
The function pcs_parse_one_pinctrl_entry() calls pcs_parse_pinconf()
if PCS_HAS_PINCONF is enabled. The function pcs_parse_pinconf()
returns 0 to indicate there was no error and num_maps is then set to 2:
980 static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,
981 struct device_node *np,
982 struct pinctrl_map **map,
983 unsigned *num_maps,
984 const char **pgnames)
985 {
<snip>
1053 (*map)->type = PIN_MAP_TYPE_MUX_GROUP;
1054 (*map)->data.mux.group = np->name;
1055 (*map)->data.mux.function = np->name;
1056
1057 if (PCS_HAS_PINCONF && function) {
1058 res = pcs_parse_pinconf(pcs, np, function, map);
1059 if (res)
1060 goto free_pingroups;
1061 *num_maps = 2;
1062 } else {
1063 *num_maps = 1;
1064 }
However, pcs_parse_pinconf() will also return 0 if !PCS_HAS_PINCONF or
!nconfs. I believe these conditions should indicate that no map was
added by returning -ENOTSUPP. Otherwise pcs_parse_one_pinctrl_entry()
will set num_maps = 2 even though no maps were successfully added, as
it does not reach "m++" on line 940:
895 static int pcs_parse_pinconf(struct pcs_device *pcs, struct device_node *np,
896 struct pcs_function *func,
897 struct pinctrl_map **map)
898
899 {
900 struct pinctrl_map *m = *map;
<snip>
917 /* If pinconf isn't supported, don't parse properties in below. */
918 if (!PCS_HAS_PINCONF)
919 return 0;
920
921 /* cacluate how much properties are supported in current node */
922 for (i = 0; i < ARRAY_SIZE(prop2); i++) {
923 if (of_find_property(np, prop2[i].name, NULL))
924 nconfs++;
925 }
926 for (i = 0; i < ARRAY_SIZE(prop4); i++) {
927 if (of_find_property(np, prop4[i].name, NULL))
928 nconfs++;
929 }
930 if (!nconfs)
919 return 0;
932
933 func->conf = devm_kcalloc(pcs->dev,
934 nconfs, sizeof(struct pcs_conf_vals),
935 GFP_KERNEL);
936 if (!func->conf)
937 return -ENOMEM;
938 func->nconfs = nconfs;
939 conf = &(func->conf[0]);
940 m++;
This situtation will cause a boot failure [0] on the BeagleBone Black
(AM3358) when am33xx_pinmux node in arch/arm/boot/dts/am33xx-l4.dtsi
has compatible = "pinconf-single" instead of "pinctrl-single".
The patch fixes this issue by returning -ENOSUPP when !PCS_HAS_PINCONF
or !nconfs, so that pcs_parse_one_pinctrl_entry() will know that no
map was added.
Logic is also added to pcs_parse_one_pinctrl_entry() to distinguish
between -ENOSUPP and other errors. In the case of -ENOSUPP, num_maps
is set to 1 as it is valid for pinconf to be enabled and a given pin
group to not any pinconf properties.
[0] https://lore.kernel.org/linux-omap/20200529175544.GA3766151@x1/
Fixes: 9dddb4df90 ("pinctrl: single: support generic pinconf")
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200608125143.GA2789203@x1
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following warnings caused by reusage of the same irq_chip
instance for all spmi-gpio gpio_irq_chip instances. Instead embed
irq_chip into pmic_gpio_state struct.
gpio gpiochip2: (c440000.qcom,spmi:pmic@2:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip3: (c440000.qcom,spmi:pmic@4:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip4: (c440000.qcom,spmi:pmic@a:gpio@c000): detected irqchip that is shared with multiple gpiochips: please fix the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200604002817.667160-1-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.8 kernel cycle.
It's just really boring this time. Zero core changes. Just linear
development, cleanups and misc noncritical fixes. Some new drivers for
very new Qualcomm and Intel chips.
New drivers:
- Intel Jasper Lake support.
- NXP Freescale i.MX8DXL support.
- Qualcomm SM8250 support.
- Renesas R8A7742 SH-PFC support.
Driver improvements:
- Severe cleanup and modernization of the MCP23s08 driver.
- Mediatek driver modularized.
- Setting config supported in the Meson driver.
- Wakeup support for the Broadcom BCM7211"
* tag 'pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: sprd: Fix the incorrect pull-up definition
pinctrl: pxa: pxa2xx: Remove 'pxa2xx_pinctrl_exit()' which is unused and broken
pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'
pinctrl: freescale: imx: Fix an error handling path in 'imx_pinctrl_probe()'
pinctrl: sirf: add missing put_device() call in sirfsoc_gpio_probe()
pinctrl: imxl: Fix an error handling path in 'imx1_pinctrl_core_probe()'
pinctrl: bcm2835: Add support for wake-up interrupts
pinctrl: bcm2835: Match BCM7211 compatible string
dt-bindings: pinctrl: Document optional BCM7211 wake-up interrupts
dt-bindings: pinctrl: Document 7211 compatible for brcm, bcm2835-gpio.txt
dt-bindings: pinctrl: stm32: Add missing interrupts property
pinctrl: at91-pio4: Add COMPILE_TEST support
pinctrl: Fix return value about devm_platform_ioremap_resource()
MAINTAINERS: Renesas Pin Controllers are supported
dt-bindings: pinctrl: ocelot: Add Sparx5 SoC support
pinctrl: ocelot: Fix GPIO interrupt decoding on Jaguar2
pinctrl: ocelot: Remove instance number from pin functions
pinctrl: ocelot: Always register GPIO driver
dt-bindings: pinctrl: rockchip: update example
pinctrl: amd: Add ACPI dependency
...
Commit 6d33ee7a05 ("pinctrl: pxa: Use devm_pinctrl_register() for pinctrl registration")
has turned a 'pinctrl_register()' into 'devm_pinctrl_register()' in
'pxa2xx_pinctrl_init()'.
However, the corresponding 'pinctrl_unregister()' call in
'pxa2xx_pinctrl_exit()' has not been removed.
This is not an issue, because 'pxa2xx_pinctrl_exit()' is unused.
Remove it now to avoid some wondering in the future and save a few LoC.
Fixes: 6d33ee7a05 ("pinctrl: pxa: Use devm_pinctrl_register() for pinctrl registration")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/20200531073716.593343-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A coccicheck run provided information like the following:
drivers/pinctrl/sirf/pinctrl-sirf.c:798:2-8: ERROR: missing put_device;
call of_find_device_by_node on line 792, but without a corresponding
object release within this function.
Generated by: scripts/coccinelle/free/put_device.cocci
Thus add a jump target to fix the exception handling for this
function implementation.
Fixes: 5130216265 ("PINCTRL: SiRF: add GPIO and GPIO irq support in CSR SiRFprimaII")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20200603013532.755220-1-yukuai3@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Leverage the IRQCHIP_MASK_ON_SUSPEND flag in order to avoid having to
specifically treat the GPIO interrupts during suspend and resume, and
simply implement an irq_set_wake() callback that is responsible for
enabling the parent wake-up interrupt as a wake-up interrupt.
To avoid allocating unnecessary resources for other chips, the wake-up
interrupts are only initialized if we have a brcm,bcm7211-gpio
compatibility string.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200531001101.24945-5-f.fainelli@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
