If we have no beacon data before association, delay smart FIFO
enablement until after we have this data.
Not doing so can cause association failures in extremely silent
environments (usually only a shielded box/room) as beacon RX is
not sent to the host immediately, and then the association time
event ends without the host receiving any beacon even though it
was on the air - it's just stuck on the FIFO.
Cc: <stable@vger.kernel.org> [3.14]
Fixes: 1f3b0ff8ec ("iwlwifi: mvm: Add Smart FIFO support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This fixes the build for powerpc:
After merging the final tree, today's linux-next build (powerpc allyesconfig)
failed like this:
drivers/net/wireless/iwlwifi/mvm/debugfs.c: In function 'iwl_dbgfs_fw_error_dump_release':
drivers/net/wireless/iwlwifi/mvm/debugfs.c:161:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
vfree(file->private_data);
^
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The current firmware advertises support for uAPSD, but
critical bugs force us to disable the feature.
When a fixed firmware will be available, we will be able to
re-enable uAPSD.
Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the low-latency update is called but there's no change then
ignore the update instead of triggering all the required work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove a spurious blank line in the quota code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of system low latency configure passive scan to be fragmented.
Set the following scan parameters for both immediate and scheduled scan:
- passive scan fragment duration = 20ms
- out-of-channel time = 70ms
- suspend time = 105ms
Restructure channel's active/passive dwell time configuration to better
suit the above change.
The idea is that under low latency traffic passive scan is fragmented,
i.e. that dwell on a particular channel will be fragmented. Each
fragment dwell time is 20ms and fragments period is 105ms. Skipping to
next channel will be delayed by the same period (105ms). So suspend_time
parameter describing both fragments and channels skipping periods is set
to 105ms. This value is chosen so that overall passive scan duration
will not be too long. Max_out_time in this case is set to 70ms, so for
active scanning operating channel will be left for 70ms while for
passive still for 20ms (fragment dwell).
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some scan parameters should be dependent on traffic conditions.
Centralize conditions verification in one function and obtain
scan max out-of-channel and suspend time in that new function.
Rely on bound interfaces indication instead of association state
to calculate scan parameters. If no bound interfaces use default
values for out-of-channel and suspend time parameters.
Additionally, get rid of NL80211_SCAN_FLAG_LOW_PRIORITY checks
since no use case for this exists so far.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[reword commit log a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware decided to not implement this API in this way,
so for now remove setting the field completely. This will
allow the firmware to change how to use this field later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to debug the firmware, we need to be able to set
the BT priority of WiFi packets. This priority is set based
on the type of the packet (control frames, EAPOL etc...).
For debugging purposes, allow to override this priority by
a debugfs controlled value.
Enable this feature that needs this priority to be able to
test it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the firmware asserts, the driver will dump the firmware
state to an internal buffer. This buffer is kept aside until
it is dumped through debugfs. Once an external application
fetched the data, the buffer is freed and a new buffer can
be allocated in case another assert occurs.
A udev event is sent to trigger an external application.
A simple rule like:
DRIVER=="iwlwifi", ACTION=="change", RUN+="/sbin/dump_sram.sh"
can fetch the data from debugfs.
Here is my dump_sram.sh:
phyname=$(basename ${DEVPATH})
date=$(date +%F_%H_%M)
filename=/var/log/iwl-sram-${phyname}-${date}.bin
cat /sys/kernel/debug/ieee80211/${phyname}/iwlwifi/iwlmvm/fw_error_dump > ${filename}
The current SRAM size is 80KB so, currently:
$ ls -lh iwl-sram-phy0-2014-03-16_13_14.bin
-rw-r--r-- 1 emmanuel emmanuel 81K Mar 16 13:15 iwl-sram-phy0-2014-03-16_13_14.bin
and after compression:
$ ls -lh iwl-sram-phy0-2014-03-16_13_14.bin.xz
-rw-r--r-- 1 emmanuel emmanuel 13K Mar 16 13:15 iwl-sram-phy0-2014-03-16_13_14.bin.xz
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable protocol offloading (arp and NS) on D0i3.
The offloading allows the fw answer NS and arp requests
without waking up the host.
Since protocol offloading is saved between D0i3
entries, we have to explicitly disable it in
case we don't want it.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to restore the qos seq number on d0i3 exit,
we need to read it from the wowlan status.
However, in order to make sure we use correct seq num
for tx frames, we need to defer any outgoing frames,
and re-enqueue them only after the seq num is configured
correctly.
Sync new Tx aggregations with D0i3 so that the correct
seq num is used for them. Wait synchronously for D0i3
exit before starting a new Tx agg.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Configure the QoS counters when entering D0i3.
The fw might use them later when performing protocol
offloading (we'll update the the counters back on
d0i3 exit in a following patch).
Non-QoS counter is handled internally in the fw, so
no need to configure it.
Also, add support for a new version of WOWLAN_CONFIG_CMD
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable beacon filter only if at least one beacon from candidate
AP is received before or after association. Check this condition before
enabling BF upon secured association completion. Add BF enablement to
mac80211 event that indicates beacon is received after association.
Too early beacon filtering enablement can lead to disconnection due to
missing AP's beacon after association.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Blink led mode is not supported by iwlmvm. This doesn't mean
that we should prevent any operation if it is selected by
the user.
Instead of failing without any notice to the user, fallback
to the default mode (RF mode) if the blink mode
is selected and print an error to inform the user.
Reported-by: Steven Haigh <netwiz@crc.id.au>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
instead of duplicating the same loop multiple times,
use a new function for it.
this will be later used also for clearing other
windows in the table.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Make _rs_collect_tx_data get window as param, in order
to be able to set various windows.
This will be used later for saving tpc statistics
as well.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently RTS protection was done whenever trasnmitting an AMPDU.
This limits throughput in cases where there's no need for protection.
Disable this too inclusive protection for now.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We should explore all possible columns when searching to be
as resilient as possible to changing conditions. This fixes
for example a scenario where even after a sudden creation of
rssi difference between the 2 antennas we would keep doing MIMO
at a low rate instead of switching to SISO at a higher rate using
the better antenna which was the optimal configuration.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Scheduled scan was disabled because it was broken. Now it is
fixed and got disabled by mistake by a merge.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We can now define the priority against BT per AC. This is
possible with a newer firmware that allows to define the
priority with 2 bits.
Note that this change is compatible with older firmware
since older firmware will simply ignore the new bit (11),
and we still set the old bit (12) in the same cases as
before.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This code is really related to BT Coex - move it to the coex
file.
Also - prepare for a FW API change that will happen soon:
Bits 11 and 12 will be allocated for BT priority. Today, we
only have bit 12.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
7265 features a new calibration which is called antenna
coupling. The purpose of this calibration (which isn't
really a calibration), is to measure the isolation between
the antennas and that can give us useful information for
the Coex modules.
With this information, we can tune the LookUpTables (LUTs)
that define the BT / WiFi contention policy.
The LUTs currently contain dummy values - but they will be
updated soon.
While at it, change the current code to stop duplicate the
host command while sending. This was needed back then, when
the command was short enough to be allocated on the stack.
Since then, the command grew a lot and is now allocated on
the heap - hence we can use the NOCOPY option instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is a flow in which we send the host command in SYNC
mode, but we don't take priv->mutex.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1046495
Cc: <stable@vger.kernel.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A scheduled scan is a more persistent setting and should take priority
over temporary regular scans. Abort the regular when a sched_scan
request arrives and then request the sched_scan.
The kernel API allows sending a sched_scan without canceling a regular
scan in progress, so this is our way to abstract the FW's limitations.
Make the scan-cancel Rx handler async and flush after invocation to
ensure new scans can't creep in before it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
cfg80211 assumes a scheduled scan is stopped synchronously. Wait for the
FW before returning to caller.
Don't do anything in the async handler in the stop-from-above flow.
There's no need to call the mac80211 sched-scan completion as the
cleanup will be automatic. Make sure the async handler is called before
the next incoming scan changes the scan_status by flushing the async
handlers after all invocations.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Check for both cfg->d0i3 and fw d0i3 support in order
to enable d0i3 support.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
BGN SKU won't scan on 5.2GHz obviously, but the firmware
still expects the driver to reserve space for the the probe
request for the 5.2GHz band.
Fix this by allocating space and leave it empty.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=69541
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When indicating RF-kill toggle to the higher layer, that
may in turn call back to the transport (for MVM at least)
to turn off the device quickly. Instead of that, allow it
to return whether or not the device should be turned off,
this gets rid of the call indirection and will help make
the API more consistent when we go back to non-threaded
interrupts again for PCIe.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
1. Enable LP XTAL to avoid HW bug where device may consume much
power if FW is not loaded after device reset. LP XTAL is
disabled by default after device HW reset. Configure device's
"persistence" mode to avoid resetting XTAL again when SHRD_HW_RST
occurs in S3.
2. Add methods to access SHR (shared block memory space) directly from PCI
bus w/o need to power up MAC HW.
Shared internal registers (e.g. SHR_APMG_GP1, SHR_APMG_XTAL_CFG)can be
accessed directly from PCI bus through SHR arbiter even when MAC HW is
powered down. This is possible due to indirect read/write via
HEEP_CTRL_WRD_PCIEX_CTRL (0xEC) and HEEP_CTRL_WRD_PCIEX_DATA (0xF4)
registers.
Use iwl_write32()/iwl_read32() family to access these registers. The MAC HW
need not be powered up so no "grab inc access" is required.
For example, to read from SHR_APMG_GP1 register (0x1DC),
first, write to the control register:
HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register)
HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 2 (read access)
second, read from the data register HEEP_CTRL_WRD_PCIEX_DATA[31:0].
To write the register, first, write to the data register
HEEP_CTRL_WRD_PCIEX_DATA[31:0] and then:
HEEP_CTRL_WRD_PCIEX_CTRL[15:0] = 0x1DC (offset of the SHR_APMG_GP1 register)
HEEP_CTRL_WRD_PCIEX_CTRL[29:28] = 3 (write access)
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When power update is initiated on BSS STA while P2P client
exists, the power command will be sent only on BSS STA vif
ignoring P2P client.
Since the firmware has symmetric constraints on the power
save enablement we can simplify the code a bit.
The current firmware doesn't know how to enable power
management on P2P client. Even BSS power management must
be disabled when a P2P client is added.
Future firmware will support power save on BSS and P2P client
as long as they are on different channels.
This was buggy since we didn't disable power management on
P2P client interface if BSS added on the same channel.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As the antenna dependent fields depend on the firmware file and not
the NVM, use those fields in the VHT capability creation.
Additionally, fix the STBC and antenna pattern consistency fields.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New firmware enforce valid values for the quota in D3.
The values given to the firmware when suspending and using
WoWLAN where dummy - change them to realistics values.
Tested-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Switch pos to char * which makes the code a bit shorter
as well as other minor cleanups suggested by Joe Perches.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This message triggers on systems that don't support the API,
so suppress them when not debugging as it's not useful to
see it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Otherwise lockdep complains about the lock, I'm not sure
why we didn't see this before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Update of the HW IDs for the 7265 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since the statistics handler is asynchrous, it can very well
be that we will handle the statistics (hence the RSSI
fluctuation) when we already disassociated.
Don't WARN on this case.
This solves: https://bugzilla.redhat.com/show_bug.cgi?id=1071998
Cc: <stable@vger.kernel.org> [3.10+]
Fixes: 2b76ef1308 ("iwlwifi: mvm: implement reduced Tx power")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Only the first packet is currently handled correctly, but then
all others are assumed to have failed which is problematic. Fix
this, marking them all successful instead (since if they're not
then the firmware will have transmitted them as single frames.)
This fixes the lost packet reporting.
Also do a tiny variable scoping cleanup.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[Add the dvm part]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some APs reject STA association request if a listen interval value exceeds
a threshold of 10. Thus, for example, Cisco APs may deny STA associations
returning status code 12 (Association denied due to reason outside the scope
of 802.11 standard) in the association response frame.
Fixing the issue by setting the default IWL_CONN_MAX_LISTEN_INTERVAL value
from 70 to 10.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We use the TLV flags as a handshake between the firmware
and the driver. These flags allow the firmware to advertise
its capabilities and API version.
Since we are running short of bits, we add a new
infrastructure which is more scalable, yet backward
compatible.
We make now the difference between API changes and the
capabilities. Both can have an index which allows to scale
at will.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This define is a leftover from dvm (in mvm, it
was replaced by MVM_UCODE_ALIVE_TIMEOUT).
Signed-off-by: Inbal Hacohen <Inbal.Hacohen@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
