Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND changes:
Core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
* Cleanup/simplification of a few aspects in the driver
* Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
* Use of_device_get_match_data() instead of of_match_device()
* Add an entry in MAINTAINERS for this driver
* Fix nand-ecc-step-size and nand-ecc-strength description in the DT
bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR changes:
Core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
* Mark the driver as "dangerous" in Kconfig
* Fix atomic sequence handling
* Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
* fix a typo in a function name
* add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line
-----BEGIN PGP SIGNATURE-----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=cHjU
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core changes:
- Add a sysfs attribute to expose available OOB size
Driver changes:
- Remove HAS_DMA dependency on various drivers
- Use dev_get_drvdata() instead of platform_get_drvdata() in docg3
- Replace msleep by usleep_range() in the dataflash driver
- Avoid VLA usage in nftl layers
- Remove useless .owner assignment in pismo
- Fix various issues in the CFI driver
- Improve TRX partition handling expose a DT compat for this part
parser
- Clarify OFFSET_CONTINUOUS meaning
NAND core changes:
- Add Miquel as a NAND maintainer
- Add access mode to the nand_page_io_req struct
- Fix kernel-doc in rawnand.h
- Support bit-wise majority to recover from corrupted ONFI parameter
pages
- Stop checking FAIL bit after a SET_FEATURES, as documented in the
ONFI spec
Raw NAND Driver changes:
- Fix and cleanup the error path of many NAND controller drivers
- GPMI:
+ Cleanup/simplification of a few aspects in the driver
+ Take ECC setup specified in the DT into account
- sunxi: remove support for GPIO-based R/B polling
- MTK:
+ Use of_device_get_match_data() instead of of_match_device()
+ Add an entry in MAINTAINERS for this driver
+ Fix nand-ecc-step-size and nand-ecc-strength description in the
DT bindings doc
- fsl_ifc: fix ->cmdfunc() to read more than one ONFI parameter page
OneNAND driver changes:
- samsung: use dev_get_drvdata() instead of platform_get_drvdata()
SPI NOR core changes:
- Add support for a bunch of SPI NOR chips
- Clear EAR reg when switching to 3-byte addressing mode on Winbond
chips
SPI NOR controller driver changes:
- cadence: Add DMA support for direct mode reads
- hisi: Prefix a few functions with hisi_
- intel:
+ Mark the driver as "dangerous" in Kconfig
+ Fix atomic sequence handling
+ Pass a 40us delay (instead of 0us) to readl_poll_timeout()
- fsl:
+ fix a typo in a function name
+ add support for IP variants embedded in the ls2080a and ls1080a
SoCs
- stm32: request exclusive control of the reset line"
* tag 'mtd/for-4.18' of git://git.infradead.org/linux-mtd: (66 commits)
mtd: nand: Pass mode information to nand_page_io_req
mtd: cfi_cmdset_0002: Change erase one block to enable XIP once
mtd: cfi_cmdset_0002: Change erase functions to check chip good only
mtd: cfi_cmdset_0002: Change erase functions to retry for error
mtd: cfi_cmdset_0002: Change definition naming to retry write operation
mtd: cfi_cmdset_0002: Change write buffer to check correct value
mtd: cmdlinepart: Update comment for introduction of OFFSET_CONTINUOUS
mtd: bcm47xxpart: add of_match_table with a new DT binding
dt-bindings: mtd: document Broadcom's BCM47xx partitions
mtd: spi-nor: Add support for EN25QH32
mtd: spi-nor: Add support for is25wp series chips
mtd: spi-nor: Add Winbond w25q32jv support
mtd: spi-nor: fsl-quadspi: add support for ls2080a/ls1080a
mtd: spi-nor: stm32-quadspi: explicitly request exclusive reset control
mtd: spi-nor: intel: provide a range for poll_timout
mtd: spi-nor: fsl-quadspi: fix api naming typo _init_ahb_read
mtd: spi-nor: intel-spi: Explicitly mark the driver as dangerous in Kconfig
mtd: spi-nor: intel-spi: Fix atomic sequence handling
mtd: rawnand: Do not check FAIL bit when executing a SET_FEATURES op
mtd: rawnand: use bit-wise majority to recover the ONFI param page
...
The current Cadence QSPI driver caused a kernel panic when loading
a Root Filesystem from QSPI. The problem was caused by reading more
bytes than needed because the QSPI operated on 4 bytes at a time.
<snip>
[ 7.947754] spi_nor_read[1048]:from 0x037cad74, len 1 [bfe07fff]
[ 7.956247] cqspi_read[910]:offset 0x58502516, buffer=bfe07fff
[ 7.956247]
[ 7.966046] Unable to handle kernel paging request at virtual
address bfe08002
[ 7.973239] pgd = eebfc000
[ 7.975931] [bfe08002] *pgd=2fffb811, *pte=00000000, *ppte=00000000
</snip>
Notice above how only 1 byte needed to be read but by reading 4 bytes
into the end of a mapped page, an unrecoverable page fault occurred.
This patch uses a temporary buffer to hold the 4 bytes read and then
copies only the bytes required into the buffer. A min() function is
used to limit the length to prevent buffer overflows.
Request testing of this patch on other platforms. This was tested
on the Intel Arria10 SoCFPGA DevKit.
Fixes: 0cf1725676 ("mtd: spi-nor: cqspi: Fix build on arches missing readsl/writesl")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add support to use DMA over memory mapped reads in direct mode. This
helps in reducing CPU usage from ~100% to ~10% when reading data from
flash. For non-DMA'able/vmalloc'd buffers, driver just falls back to CPU
based memcpy.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Cadence QSPI controller provides direct access mode through which flash
can be accessed in a memory-mapped IO mode. This enables read/write to
flash using memcpy*() functions. This mode provides higher throughput
for both read/write operations when compared to current indirect mode of
operation.
This patch therefore adds support to use QSPI in direct mode. If the
window reserved in SoC's memory map for MMIO access is less that of
flash size(like on most SoCFPGA variants), then the driver falls back
to indirect mode of operation.
On TI's 66AK2G SoC, with ARM running at 600MHz and QSPI at 96MHz
switching to direct mode improves read throughput from 3MB/s to 8MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Move configuring of indirect read/write start address to
cqspi_indirect_*_execute() function and rename cqspi_indirect_*_setup()
function. This will help to reuse cqspi_indirect_*_setup() function for
supporting direct access mode.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Add pm_runtime* calls to cadence-quadspi driver. This is required to
switch on QSPI power domain on TI 66AK2G SoC during probe.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Fix the reversed goto labels, so that we disable cqspi controller only
if its enabled previously. This is a minor cleanup.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cadence QSPI IP has a adapted loop-back circuit which can be enabled by
setting BYPASS field to 0 in READCAPTURE register. It enables use of
QSPI return clock to latch the data rather than the internal QSPI
reference clock. For high speed operations, adapted loop-back circuit
using QSPI return clock helps to increase data valid window.
Based on DT parameter cdns,rclk-en enable adapted loop-back circuit
for boards which do have QSPI return clock provided.
This patch also modifies cqspi_readdata_capture() function's bypass
parameter to bool to match how its used in the function.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
As per 66AK2G02 TRM[1] SPRUHY8F section 11.15.5.3 Indirect Access
Controller programming sequence, a delay equal to couple of QSPI master
clock(~5ns) is required after setting CQSPI_REG_INDIRECTWR_START bit and
writing data to the flash. Introduce a quirk flag CQSPI_NEEDS_WR_DELAY
to handle this and set this flag for TI 66AK2G SoC.
[1]http://www.ti.com/lit/ug/spruhy8f/spruhy8f.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
The variable was already marked 'const' before the previous
patch, but the qualifier was in an unusual place, and now the
extra 'const' causes a harmless warning:
drivers/mtd/spi-nor/cadence-quadspi.c:1286:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
This removes the other 'const' instead.
Fixes: f993c123b4 ("mtd: spi-nor: cqspi: make of_device_ids const")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
This patch changes the prototype of spi_nor_scan(): its 3rd parameter
is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor
framework about the actual hardware capabilities supported by the SPI
controller and its driver.
Besides, this patch also introduces a new 'struct spi_nor_flash_parameter'
telling the spi-nor framework about the hardware capabilities supported by
the SPI flash memory and the associated settings required to use those
hardware caps.
Then, to improve the readability of spi_nor_scan(), the discovery of the
memory settings and the memory initialization are now split into two
dedicated functions.
1 - spi_nor_init_params()
The spi_nor_init_params() function is responsible for initializing the
'struct spi_nor_flash_parameter'. Currently this structure is filled with
legacy values but further patches will allow to override some parameter
values dynamically, for instance by reading the JESD216 Serial Flash
Discoverable Parameter (SFDP) tables from the SPI memory.
The spi_nor_init_params() function only deals with the hardware
capabilities of the SPI flash memory: especially it doesn't care about
the hardware capabilities supported by the SPI controller.
2 - spi_nor_setup()
The second function is called once the 'struct spi_nor_flash_parameter'
has been initialized by spi_nor_init_params().
With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps',
the new argument of spi_nor_scan(), spi_nor_setup() computes the best
match between hardware caps supported by both the (Q)SPI memory and
controller hence selecting the relevant settings for (Fast) Read and Page
Program operations.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Checking for ret < 0 is redundant because a previous check on ret
being non-zero already handles the ret < 0 case. Remove the redundant
code. Found by CoverityScan, CID#1398863, CID#1398864
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The x86-64 and some other architectures are missing readsl/writesl
functions, so this driver won't build on them. Use a more portable
ioread32_rep()/iowrite32_rep() instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Graham Moore <grmoore@opensource.altera.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Yves Vandervennet <yvanderv@opensource.altera.com>
Suggested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
We return success or possibly uninitialized values on these error paths
instead of proper error codes.
Fixes: 1406234105 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
There are CQSPI_MAX_CHIPSELECT elements in the ->f_pdata array so the >
should be >=.
Fixes: 1406234105 ('mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Add support for the Cadence QSPI controller. This controller is
present in the Altera SoCFPGA SoCs and this driver has been tested
on the Cyclone V SoC.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Graham Moore <grmoore@opensource.altera.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Yves Vandervennet <yvanderv@opensource.altera.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
