Previously the "vendor" and "product" IDs for the elan_i2c driver simply
reported 0000. This patch modifies the elan_i2c driver to include the
Elan vendor ID and the touchpad's product id under
input/input*/{vendor,product}.
Specifically, this is to allow us to apply a generic Elan gestures config
that will apply to all Elan touchpads on ChromeOS. These configs match to
input devices in various ways, but one major way is by matching on vendor
ID. Adding this patch allows the default Elan touchpad config to be
applied to Elan touchpads in this kernel by matching on devices that have
vendor ID 04f3.
Note that product ID is also available via custom sysfs entry "product_id"
as well.
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to support more projects in the future, we expand the
maximum product_id value form 0xFF to 0xFFFF.
Signed-off by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Asus X456UA has an ELAN1000 touchpad with IAP version 0xe. This is
unknown to elan_get_fwinfo() so driver probe fails and I am left with an
unusable touchpad.
However, the fwinfo is not required for general driver usage, it is only
needed if the user decides to upload new firmware.
Adjust the driver so that we do not abort probe when we encounter
unexpected IAP version, but rather warn user that firmware update feature
of the driver will not work.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When driver is in IAP mode ic_type query may return 0xff. However
iap_version will always be valid, so let's use it to determine parameters
of the firmware that the controller is supposed to accept.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It takes a bit of time to go through controller power up sequence and
initialization. To not stall the overall boot progress let's probe the
controller asynchronously, given that userspace is usually prepared for
hot-plugging of input devices and thus does not rely on particular
ordering.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ELAN0600 seems to work just fine in mouse emulation mode through i2c-hid,
but to have full raw touch support we need to register it in elan_i2c.ko
Reported-and-tested-by: Alessio Treglia <alessio@debian.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The firmware only reports hover condition while the very first contact is
approaching the surface; the hover is not reported for the subsequent
contacts. Therefore we should not be using ABS_MT_DISTANCE to report hover
but rather its single-touch counterpart ABS_DISTANCE.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously the elan_i2c touchpad driver would simply request the firmware
"/lib/firmware/elan_i2c.bin", which does not work well if there are
multiple such devices in the system.
Let's append the "product ID" (by using the same function as the sysfs
interface for consistency) to the filename. This results in filenames of
the form "/lib/firmware/elan_i2c_72.0.bin", allowing you to support
multiple elan_i2c touchpads on the same device by simply naming each
device's FW with its corresponding product ID. This way when you trigger a
fw update the driver will load the correct binary.
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to support multiple IC types for i2c/smbus protocol, add get ic
type command and use this data when checking firmware page count and
signature address.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When hover is detected report ABS_MT_DISTANCE as 1; for active contacts
the distance is reported as 0.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get pressure format flag from firmware to check if we need to normalize
pressure data before reporting it.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to better diagnose potential issues let's return error to the
upper layers when resuming the device fails and also add a few diagnostic
messages.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To allow for different firmware sizes let's replace the original size check
with with checking the signature in the firmware data.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
