Instead of installing a trap before tests run and uninstalling it after
they run, mirror_vlan.sh installs it twice due to a typo. Fix the typo.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add regression tests for PF_PACKET transmission using packet_snd.
The TPACKET ring interface has tests for transmission and reception.
This is an initial stab at the same for the send call based interface.
Packets are sent over loopback, then read twice. The entire packet is
read from another packet socket and compared. The packet is also
verified to arrive at a UDP socket for protocol conformance.
The test sends a packet over loopback, testing the following options
(not the full cross-product):
- SOCK_DGRAM
- SOCK_RAW
- vlan tag
- qdisc bypass
- bind() and sendto()
- virtio_net_hdr
- csum offload (NOT actual csum feature, ignored on loopback)
- gso
Besides these basic functionality tests, the test runs from a set
of bounds checks, positive and negative. Running over loopback, which
has dev->min_header_len, it cannot generate variable length hhlen.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify that udpgso can generate segments smaller than device mtu, down
to the extreme case of 1B gso_size.
Verify that irrespective of gso_size, udpgso restricts the number of
segments it will generate per call (UDP_MAX_SEGMENTS).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing msg_zerocopy test takes additional protocol arguments.
Add a variant that takes no arguments and runs all supported variants.
Call this from kselftest.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test offloading of mirror-to-gretap in mlxsw for cases that a
VLAN-unaware bridge is in underlay packet path, test that the STP status
of bridge egress port is reflected.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offloading of mirror-to-gretap in mlxsw is tricky especially in cases
when the gretap underlay involves bridges. Add more tests that exercise
the bridge handling code:
- forbidden_egress tests that check vlan removal on bridge port in the
underlay packet path
- untagged_egress tests that similarly check "egress untagged"
- fdb_roaming tests that check whether learning FDB on a different port
is reflected
- stp tests for handling port STP status of bridge egress port
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename test_gretap_forbidden() and test_ip6gretap_forbidden() to a more
specific test_gretap_forbidden_cpu() and test_ip6gretap_forbidden_cpu().
This will make it clearer which is which when further down a patch is
introduced that forbids a VLAN on regular bridge port.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the final change reestablishes the original configuration, make
sure the traffic flows again as it should.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "ip6gretap" in the test name refers to the tunnel device type that
the test is supposed to be testing. However test_ip6gretap_forbidden()
tests, due to a typo, a gretap tunnel. Fix the typo.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a reusable full test that toggles STP state of a given bridge port
and checks that the mirroring reacts appropriately. The test will be
used by bridge tests in follow-up patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VLAN capture is installed on a front panel device and not a
soft device, the packets are counted twice: once in fast path, and once
after they are trapped to the kernel. Resolve the problem by passing
skip_hw flag to vlan_capture_install().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the function do_test_span_vlan_dir_ips() from mirror_vlan.sh test
to a library file mirror_lib.sh to allow reuse. Fill in other entry
points similar to other testing functions in mirror_lib.sh, they will be
useful in following patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move vlan_capture_install() and vlan_capture_uninstall() from
mirror_vlan.sh test to lib.sh so that it can be reused in other tests.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tests verifying prefix routes are inserted with expected metric.
IPv6 prefix route tests
TEST: Default metric [ OK ]
TEST: User specified metric on first device [ OK ]
TEST: User specified metric on second device [ OK ]
TEST: Delete of address on first device [ OK ]
TEST: Modify metric of address [ OK ]
TEST: Prefix route removed on link down [ OK ]
TEST: Prefix route with metric on link up [ OK ]
IPv4 prefix route tests
TEST: Default metric [ OK ]
TEST: User specified metric on first device [ OK ]
TEST: User specified metric on second device [ OK ]
TEST: Delete of address on first device [ OK ]
TEST: Modify metric of address [ OK ]
TEST: Prefix route removed on link down [ OK ]
TEST: Prefix route with metric on link up [ OK ]
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-05-24
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in the original fix to prevent out of bounds speculation when
multiple tail call maps from different branches or calls end up at the
same tail call helper invocation, from Daniel.
2) Two selftest fixes, one in reuseport_bpf_numa where test is skipped in
case of missing numa support and another one to update kernel config to
properly support xdp_meta.sh test, from Anders.
...
Would be great if you have a chance to merge net into net-next after that.
The verifier fix would be needed later as a dependency in bpf-next for
upcomig work there. When you do the merge there's a trivial conflict on
BPF side with 849fa50662 ("bpf/verifier: refine retval R0 state for
bpf_get_stack helper"): Resolution is to keep both functions, the
do_refine_retval_range() and record_func_map().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
PMTU tests in pmtu.sh need support for VTI, VTI6 and dummy
interfaces: add them to config file.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: d1f1b9cbf3 ("selftests: net: Introduce first PMTU test")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test for "tc action mirred egress mirror" that mirrors to GRE when the
underlay route points at an 802.1d bridge and packet egresses through a
VLAN device.
Besides testing basic connectivity, this also tests that the traffic is
properly tagged.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test for "tc action mirred egress mirror" that mirrors to a gretap
netdevice whose underlay route points at a vlan device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test for "tc action mirred egress mirror" that mirrors to GRE when the
underlay route points at a vlan device on top of a bridge device with
vlan filtering (802.1q).
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test for "tc action mirred egress mirror" that mirrors to a vlan device.
- test_vlan() tests that the packets get mirrored
- test_tagged_vlan() tests that the mirrored packets have correct inner
VLAN tag.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mirror-to-vlan test that's coming next needs to install the trap
unconditionally. Therefore extract from slow_path_trap_{,un}install()
a more generic functions trap_install() and trap_uninstall(), and covert
the former two to conditional wrappers around these.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add full_test_span_gre_dir_vlan_ips() and full_test_span_gre_dir_vlan()
to support mirror-to-gre tests that involve VLAN.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add vlan_create() and vlan_destroy() to manage VLAN netdevices.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having a clsact qdisc on $h3 is useful in several tests, and will be
useful in more tests to come. Move the registration from all the tests
that need it into the topology file itself.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For non-GRE mirroring tests, a functions along the lines of
do_test_span_gre_dir_ips() and test_span_gre_dir_ips() are necessary,
but such that they don't assume tunnels are involved. Extract the code
from mirror_gre_lib.sh to mirror_lib.sh and convert to just use a given
device without assuming it's named "h3-$tundev". Convert the two
above-mentioned functions to wrappers that pass along the correct device
name.
Add test_span_dir() and fail_test_span_dir() to round up the API for use
by following patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move generic parts of mirror_gre_topo_lib.sh into a new file
mirror_topo_lib.sh. Reuse the functions in GRE topo, adding the tunnel
devices as necessary.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that when flower-based mirror action is removed, mirroring stops.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When underlay route is removed, the mirrored traffic should not be
forwarded.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tests that the mirroring code catches up with deletion of a mirrored-to
device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a first set of tests for fib rule match/action for
ipv4 and ipv6. Initial tests only cover action lookup table.
can be extended to cover other actions in the future.
Uses ip route get to validate the rule lookup.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reuseport_bpf_numa test case fails there's no numa support. The
test shouldn't fail if there's no support it should be skipped.
Fixes: 3c2c3c16aa ("reuseport, bpf: add test case for bpf_get_numa_node_id")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add IPv4 route tests covering add, append and replace permutations.
Assumes the ability to add a basic single path route works; this is
required for example when adding an address to an interface.
$ fib_tests.sh -t ipv4_rt
IPv4 route add / append tests
TEST: Attempt to add duplicate route - gw [ OK ]
TEST: Attempt to add duplicate route - dev only [ OK ]
TEST: Attempt to add duplicate route - reject route [ OK ]
TEST: Add new nexthop for existing prefix [ OK ]
TEST: Append nexthop to existing route - gw [ OK ]
TEST: Append nexthop to existing route - dev only [ OK ]
TEST: Append nexthop to existing route - reject route [ OK ]
TEST: Append nexthop to existing reject route - gw [ OK ]
TEST: Append nexthop to existing reject route - dev only [ OK ]
TEST: add multipath route [ OK ]
TEST: Attempt to add duplicate multipath route [ OK ]
TEST: Route add with different metrics [ OK ]
TEST: Route delete with metric [ OK ]
IPv4 route replace tests
TEST: Single path with single path [ OK ]
TEST: Single path with multipath [ OK ]
TEST: Single path with reject route [ OK ]
TEST: Single path with single path via multipath attribute [ OK ]
TEST: Invalid nexthop [ OK ]
TEST: Single path - replace of non-existent route [ OK ]
TEST: Multipath with multipath [ OK ]
TEST: Multipath with single path [ OK ]
TEST: Multipath with single path via multipath attribute [ OK ]
TEST: Multipath with reject route [ OK ]
TEST: Multipath - invalid first nexthop [ OK ]
TEST: Multipath - invalid second nexthop [ OK ]
TEST: Multipath - replace of non-existent route [ OK ]
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 route tests covering add, append and replace permutations.
Assumes the ability to add a basic single path route works; this is
required for example when adding an address to an interface.
$ fib_tests.sh -t ipv6_rt
IPv6 route add / append tests
TEST: Attempt to add duplicate route - gw [ OK ]
TEST: Attempt to add duplicate route - dev only [ OK ]
TEST: Attempt to add duplicate route - reject route [ OK ]
TEST: Add new route for existing prefix (w/o NLM_F_EXCL) [ OK ]
TEST: Append nexthop to existing route - gw [ OK ]
TEST: Append nexthop to existing route - dev only [ OK ]
TEST: Append nexthop to existing route - reject route [ OK ]
TEST: Append nexthop to existing reject route - gw [ OK ]
TEST: Append nexthop to existing reject route - dev only [ OK ]
TEST: Add multipath route [ OK ]
TEST: Attempt to add duplicate multipath route [ OK ]
TEST: Route add with different metrics [ OK ]
TEST: Route delete with metric [ OK ]
IPv6 route replace tests
TEST: Single path with single path [ OK ]
TEST: Single path with multipath [ OK ]
TEST: Single path with reject route [ OK ]
TEST: Single path with single path via multipath attribute [ OK ]
TEST: Invalid nexthop [ OK ]
TEST: Single path - replace of non-existent route [ OK ]
TEST: Multipath with multipath [ OK ]
TEST: Multipath with single path [ OK ]
TEST: Multipath with single path via multipath attribute [ OK ]
TEST: Multipath with reject route [ OK ]
TEST: Multipath - invalid first nexthop [ OK ]
TEST: Multipath - invalid second nexthop [ OK ]
TEST: Multipath - replace of non-existent route [ OK ]
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add option to pause after each test before cleanup is done. Allows
user to do manual inspection or more ad-hoc testing after each test
with the setup in tact.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add command line options for controlling pause on fail, controlling
specific tests to run and verbose mode rather than relying on environment
variables.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As more tests are added, it is convenient to have a tally at the end.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
When a script file that isn't generated uses the variable
TEST_GEN_PROGS_EXTENDED and a 'make -C tools/testing/selftests clean' is
performed the script file gets removed and git shows the file as
deleted. For script files that isn't generated TEST_PROGS_EXTENDED
should be used.
Fixes: 9faedd643f ("selftests: net: add in_netns.sh TEST_GEN_PROGS_EXTENDED")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generated files udpgso* shouldn't be part of TEST_PROGS, they are
used by udpgso.sh and udpgsp_bench.sh. They should be added to the
TEST_GEN_FILES to get installed without being added to the main
run_kselftest.sh script.
Fixes: 3a687bef14 ("selftests: udp gso benchmark")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test fails to work if reverse-path filtering is in effect on the
mirrored-to host interface, or for all interfaces.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of hand-managing the sysctl set and restore, use the wrappers
sysctl_set() and sysctl_restore() to do the bookkeeping automatically.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two helper functions: sysctl_set() to change the value of a given
sysctl setting, and sysctl_restore() to change it back to what it was.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit a511858c75 ("selftests: fib_tests: Allow user to run
a specific test"), allow user to run only a subset of the tests using
the TESTS environment variable.
This is useful when not all the tests can pass on a given system.
Example:
# export TESTS="ping_ipv4 ping_ipv6"
# ./bridge_vlan_aware.sh
TEST: ping [PASS]
TEST: ping6 [PASS]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We sometimes observe failures in the test due to too large discrepancy
between the measured and expected ratios. For example:
TEST: ECMP [FAIL]
Too large discrepancy between expected and measured ratios
INFO: Expected ratio 1.00 Measured ratio 1.11
Fix this by allowing an up to 15% deviation between both ratios.
Another possibility is to increase the number of generated flows, but
this will prolong the execution time of the test, which is already quite
high.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After prior kernel change, mmap() on TCP socket only reserves VMA.
We have to use getsockopt(fd, IPPROTO_TCP, TCP_ZEROCOPY_RECEIVE, ...)
to perform the transfert of pages from skbs in TCP receive queue into such VMA.
struct tcp_zerocopy_receive {
__u64 address; /* in: address of mapping */
__u32 length; /* in/out: number of bytes to map/mapped */
__u32 recv_skip_hint; /* out: amount of bytes to skip */
};
After a successful getsockopt(...TCP_ZEROCOPY_RECEIVE...), @length contains
number of bytes that were mapped, and @recv_skip_hint contains number of bytes
that should be read using conventional read()/recv()/recvmsg() system calls,
to skip a sequence of bytes that can not be mapped, because not properly page
aligned.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Andy Lutomirski <luto@kernel.org>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These tests set up mirroring in a situation that the configuration is
incorrect, i.e. mirrored packets, if any, are not supposed to reach
destination tunnel device. Then the configuration is rectified and
mirroring is checked to have started working.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
