Wipe internal irb if the clear function bit is set before accumulating
bits from the irb in order to follow hardware behaviour.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In the unlikely event that an AP device lost requests, don't forget to
update the ap_poll_requests counter too. Same must happen in case an AP
device is removed while there are still outstanding requests.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
If a AP device is unconfigured __ap_poll_all() will call
device_unregister() in software interrupt context which can cause
dead locks. To fix this the device will be only marked as unconfigured
and the device_unregister() call will be done later by either
ap_scan_bus() or ap_queue_message() in process context.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Only accumulate device status field in irb if it is valid.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
gcc incorrectly removes initialization of register 0 in dasd diag
inline assembly. Use different register to work around this compiler
bug.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Move try_module_get() call into spin protected block to prevent zcrypt
driver module unload while submitting a request to driver.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
AP bus module uses bus_for_each_dev() in software interrupt context to
poll for completed requests which might cause dead locks. Solution: use
private AP device list for polling in software interrupt context.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure set_slsb problems are handled correctly in
qdio_do_qdio_fill_input() and qdio_do_qdio_fill_output.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch (as868) adds a helper routine for device drivers that need
to set up a callback to perform some action in a different process's
context. This is intended for use by attribute methods that want to
unregister themselves or their parent device. Attribute method calls
are mutually exclusive with unregistration, so such actions cannot be
taken directly.
Two attribute methods are converted to use the new helper routine: one
for SCSI device deletion and one for System/390 ccwgroup devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The subchannel may just be status pending, even with actl == 0. We
must go through the cancel_halt_clear procedure to put the subchannel
into a defined state.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After I/O has been killed by the common I/O layer, trigger path
verification which will queue cio_device_nopath_notify itself if it
finds a device to be without paths.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure we hold the device lock when we modify the ccw device
structure but always call the notify function without the lock held.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For extended error reporting we sometimes have to start an
Sense Subsystem Status request (SNSS). When this request needs
to be recovered for some reason, the recovery request will
fail with 'command reject'.
Our usual recovery procedure will retry the failed request by
creating a new request and chaining the failed request from that
one. SNSS requests, though, must not be chained from anything,
so the recovery request will fail permanently.
Use the default recovery for SNSS request, which will just restart
the original request without further ado.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After switching compression on/off with the mt command, tape encryption is no
longer working. The reason for that is, that the modeset_byte is set to
the compression value instead of using bitwise and/or bit operations to
enable/disable the corresponding bit.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_SHARED_KERNEL the kernel text segment that might be in a
read only memory sections starts at 1MB. Memory between 0x12000 and
0x100000 is unused then. Free this, so we have appr. an extra MB
of memory available.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Setup.h has been misused for ipl related stuff in the past. We now move
everything, which has to do with ipl and reipl to a new header file named
"ipl.h".
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix compile of sclp_quiesce for CONFIG_SMP=n.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] remove __io_virt and mmiowb.
[S390] cio: use ARRAY_SIZE in device_id.c
[S390] cio: Fixup interface for setting options on ccw devices.
[S390] smp_call_function/smp_call_function_on locking.
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current ccw_device_set_options() sets a specified mask of options
and clears those not specified, but there is no way to find out which
options have already been set.
In order to fix this up, introduce the following interface changes:
ccw_device_set_options() now only sets the specified bits, but does
not clear those that are not specified.
ccw_device_clear_options() clears the specified bits.
ccw_device_set_options_mask() provides the old semantics (setting only
the specified bits and clearing the others).
Device drivers now work as expected. qdio has been adapted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (97 commits)
[SCSI] zfcp: removed wrong comment
[SCSI] zfcp: use of uninitialized variable
[SCSI] zfcp: Invalid locking order
[SCSI] aic79xx: use dma_get_required_mask()
[SCSI] aic79xx: fix bracket mismatch in unused macro
[SCSI] BusLogic: Replace 'boolean' by 'bool'
[SCSI] advansys: clean up warnings
[SCSI] 53c7xx: brackets fix in uncompiled code
[SCSI] nsp_cs: remove old scsi code
[SCSI] aic79xx: make ahd_match_scb() static
[SCSI] DAC960: kmalloc->kzalloc/Casting cleanups
[SCSI] scsi_kmap_atomic_sg(): check that local irqs are disabled
[SCSI] Buslogic: local_irq_disable() is redundant after local_irq_save()
[SCSI] aic94xx: update for v28 firmware
[SCSI] scsi_error: Fix lost EH commands
[SCSI] aic94xx: Add default bus reset handler
[SCSI] aic94xx: Remove TMF result code munging
[SCSI] libsas: Add an LU reset mechanism to the error handler
[SCSI] libsas: Don't BUG when connecting two expanders via wide port
[SCSI] st: fix Tape dies if wrong block size used, bug 7919
...
Replace a small number of expressions with a call to the "container_of()"
macro.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug: pnx8550 code creates directory but resets ->nlink to 1.
create_proc_entry() et al will correctly set ->nlink for you.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Invalid locking order. Kernel hangs after trying to take two locks
which are dependend on each other. Introducing temporary variable
to free requests. Free lock after requests are copied.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adapt special message interface to new IUCV API
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt netiucv network device driver to new IUCV API
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt vmlogrdr character device driver to new IUCV API
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt monreader character device driver to new IUCV API
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the old IUCV code from drivers/s390/net
Remove approprirate IUCV entries from drivers/s390/net/Makefile,
drivers/s390/net/Kconfig and arch/s390/defconfig
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hopefully this will make it more maintainable and less error prone.
Code makes use of search_exception_tables(). Since it calls this
function before the kernel exeception table is sorted, there is an
early call to sort_main_extable().
This way it's easy to use the already present infrastructure of fixup
sections. Also this would allows to easily convert the rest of
head[31|64].S into C code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Preset the bogomips number to the cpu capacity value reported by
store system information in SYSIB 1.2.2. This value is constant
for a particular machine model and can be used to determine
relative performance differences between machines.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
3592 tape devices are able to write data encrpyted on tape mediums.
This z/Linux device driver support includes the following functions:
* ioctl to switch on/off encryption
* ioctl to query encryption status of drive
* ioctls to set and query key encrypting keys (kekls)
* long busy interrupt handling
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds support for clock synchronization to an external time
reference (ETR). The external time reference sends an oscillator
signal and a synchronization signal every 2^20 microseconds to keep
the TOD clocks of all connected servers in sync. For availability
two ETR units can be connected to a machine. If the clock deviates
for more than the sync-check tolerance all cpus get a machine check
that indicates that the clock is out of sync. For the lovely details
how to get the clock back in sync see the code below.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Lower priority of "Blacklisted device detected" messages so we don't
overwrite more useful messages.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change CHSC event handling to be more easily extensible.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we have a subchannel id which has been generated via
for_each_subchannel(), it might contain an invalid subchannel set id.
We need to catch the ensuing operand exception by using stsch_err()
instead of stsch() in all possible cases.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The reserve/release IOCTLs sometimes do not work. If second system
does a 'steal lock' the pending unit check (Format 3 Msg F) is
delivered. Since ERP is disabled for reserve/release, the IOCTL call
fails. We have to allow basic ERP (retries) for reserve/release IOCTLs.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Logging of relevant information is already done by disciplines
dump_sense function.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
cpu_relax() has barrier() semantics hence there is no need to use both
of them in conjunction in sclp_sync_wait(). Also change cpu_relax()
so it's more obvious that it has barrier semantics.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Create/remove the channel measurement binary files with
device_{create,remove}_bin_file instead of sysfs_{create,remove}_bin_file.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
local_bh_disable/_local_bh_enable must not be called if in_irq() is
true. Besides that if in_interrupt() is true bottom halves are
disabled anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently loaded DCSS segments are now listed in /proc/iomem with
their name followed by a trailing "(DCSS)".
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we try to start path verification when an unsolicited interrupt
is already pending, stctl shows status pending and we delay path
verification again. We need to check for the doverify bit when the
unsolicited interrupt comes in and then do path verification.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The initialization of the dasd_eer code is one of the last steps of the
dasd driver initialization. When initialization fails in one of the
earlier steps, the dasd_exit function is called to clean up what has been
done so far. So the dasd_eer_exit function may be called, although the
dasd_eer_init function wasn't called before and dasd_eer_exit tries to
unregister a misc device that wasn't registered, which results in a BUG.
Make sure that dasd_eer_exit can be called without initialization. Use a
dynamically allocated struct miscdevice instead of a static one, so we
only try to unregister the device if it exists and was actually registered.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Requests are aborted when the sclp interface reports 'not operational'
even though they may still be active at the sclp, leading to concurrent
writes to request memory by both the kernel and the sclp interface.
Do not abort requests for which the sclp interface reports not
operational status during request retry.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>5A
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since ssd_info is now available before the subchannel is registered,
we don't need to check whether it is available.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Changeset 740b5706b9 moved the protecting
spinlock from __cpcmd to cpcmd. Therefore vmcp can no longer use __cpcmd,
instead we have to use cpcmd.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use barrier() in stsch_reset() instead of duplicating the stsch()
inline assembly and adding "memory" to the clobberlist.
Pointed out by Chuck Ebbert.
Real fix would be to add a fixup section to the stsch() and extend the
basic program check handler so it searches the exception tables in case
of a program check.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[PATCH 4/5] s390: iucv Kconfig help description changes
From: Ursula Braun <braunu@de.ibm.com>
remove text from help description which does not
apply anymore for 2.6 kernel series.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- qeth device functions were not callable
in atomic context due to usage of wait_event_xxx operations in qeth.
"schedule while atomic" message appeared and kernel dumped when
removing slave from bond device.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- packet socket support is not complete.
Recvfrom a packet socket does not fill the sockaddr_ll structure.
device function hard_header_parse is not implemented.
For layer 2 mode and layer 3 mode with fake_ll turned on, we have
the information to fill sockaddr_ll.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Ursula Braun <braunu@de.ibm.com>
- VLAN header reordering did not work on packets
received through qeth interface in layer 2 mode.
This caused dhcpcd not to work with VLAN devices.
- set qeth performance statistics initally inactive
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[patch] qeth: fix uaccess handling and get rid of unused variable
drivers/s390/net/qeth_main.c: In function `qeth_process_inbound_buffer':
drivers/s390/net/qeth_main.c:2563: warning: unused variable `vlan_addr'
include/asm/uaccess.h: In function `qeth_do_ioctl':
drivers/s390/net/qeth_main.c:4847: warning:
ignoring return value of `copy_to_user'
drivers/s390/net/qeth_main.c:4849: warning:
ignoring return value of `copy_to_user'
drivers/s390/net/qeth_main.c:4996: warning:
ignoring return value of `copy_to_user'
Cc: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Copy inline assembly of stsch and add "memory" to clobber list in order
to prevent gcc from optimizing away the checking of the global variable
"pgm_check_occured".
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reduce the max. buffer size for the monwriter device to prevent a
possible problem with the z/VM monitor service.
Signed-off-by: Melissa Howland <melissah@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Asynchronous probe can release memory of a subchannel before
css_get_ssd_info is called. To fix this call css_get_ssd_info
before registering with driver core.
Signed-off-by: Stefan Bader <shbader@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reboot hangs on LPARs without diag308 support. The reason for this is,
that before the reboot is done, the channel subsystem is shut down.
During the reset on each possible subchannel a "store subchannel" is
done. This operation can end in a program check interruption, if the
specified subchannel set is not implemented by the hardware. During
the reset, currently we do not have a program check handler, which
leads to the described kernel bug. We install now a new program check
handler for the reboot code to fix this problem.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sclp_cpi is GPL. Make the module not taint the kernel
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add code to reset all queues for a domain and add missing tasklet_kill
call to ap bus module exit code.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A HiperSocket multicast queue works asynchronously. When sending
buffers, the buffer state change from PRIMED to EMPTY may happen
delayed. Reschedule the checking for changes in the outbound queue,
if there are still PRIMED buffers.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Poison init section before freeing it.
[S390] Use add_active_range() and free_area_init_nodes().
[S390] Virtual memmap for s390.
[S390] Update documentation for dynamic subchannel mapping.
[S390] Use dev->groups for adding/removing the subchannel attribute group.
[S390] Support for disconnected devices reappearing on another subchannel.
[S390] subchannel lock conversion.
[S390] Some preparations for the dynamic subchannel mapping patch.
[S390] runtime switch for qdio performance statistics
[S390] New DASD feature for ERP related logging
[S390] add reset call handler to the ap bus.
[S390] more workqueue fixes.
[S390] workqueue fixes.
[S390] uaccess_pt: add missing down_read() and convert to is_init().
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the locking of signal->tty.
Use ->sighand->siglock to protect ->signal->tty; this lock is already used
by most other members of ->signal/->sighand. And unless we are 'current'
or the tasklist_lock is held we need ->siglock to access ->signal anyway.
(NOTE: sys_unshare() is broken wrt ->sighand locking rules)
Note that tty_mutex is held over tty destruction, so while holding
tty_mutex any tty pointer remains valid. Otherwise the lifetime of ttys
are governed by their open file handles. This leaves some holes for tty
access from signal->tty (or any other non file related tty access).
It solves the tty SLAB scribbles we were seeing.
(NOTE: the change from group_send_sig_info to __group_send_sig_info needs to
be examined by someone familiar with the security framework, I think
it is safe given the SEND_SIG_PRIV from other __group_send_sig_info
invocations)
[schwidefsky@de.ibm.com: 3270 fix]
[akpm@osdl.org: various post-viro fixes]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- create a 'pseudo_subchannel' per channel subsystem (the 'orphanage')
- use the orphanage as a shelter for ccw_devices that can't remain on the same
subchannel
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert the subchannel lock to a pointer to a lock. Needed for the dynamic
subchannel mapping patch.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove CONFIG_QETH_PERF_STATS and use a sysfs attribute instead.
We want to have the ability to turn the statistics on/off at runtime.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It is now possible to enable/disable ERP related logging without re-compile
and re-ipl. A additional sysfs-attribute 'erplog' allows to switch the
logging non-interruptive.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_DMA is an alias of GFP_DMA. This is the last one so we
remove the leftover comment too.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In io_subchannel_register(), it is better to just reprobe the current
device if it hasn't a driver yet than to rescan the whole bus.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If I/O was running on a just varied off chpid, it will be terminated.
If this was a common I/O layer internal I/O, it needs to be retried.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the last path to a device is gone after a chpid has been varied
off, putting it on the slow queue doesn't prevent a device driver
from still attempting to use it (it may stay on the slow queue for a
long time). Instead, trigger a verify event which will prevent I/O
attempts from the device driver immediately.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add some prefixes to constands defined in drivers/s390/net/qdio.h
and drivers/s390/lcs.h to make it possible to include the three
header files drivers/s390/net/qeth.h, drivers/s390/net/qdio.h and
drivers/net/s390/lcs.h in one C file. This is required for the
patch that generates the kerntypes.o file for use by lcrash.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Let one master cpu kill all other cpus instead of sending an external
interrupt to all other cpus so they can kill themselves.
Simplifies reipl/shutdown functions a lot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of re-IPL and diag308 doesn't work we have to reset all devices
manually and wait synchronously that each reset finished.
This patch adds the necessary infrastucture and the first exploiter of it.
Subsystems that need to add a function that needs to be called at re-IPL
may register/unregister this function via
struct reset_call {
struct reset_call *next;
void (*fn)(void);
};
void register_reset_call(struct reset_call *reset);
void unregister_reset_call(struct reset_call *reset);
When the registered function get called the context is:
- all cpus beside the current one are stopped
- all machine checks and interrupts are disabled
- prefixing is disabled
- a default machine check handler is available for use
The registered functions may not take any locks are sleep.
For the common I/O layer part of this patch:
Introduce a reset_call css_reset that does the following:
- clear all subchannels
- perform a rchp on all channel paths and wait for the resulting
machine checks
This replaces the calls to clear_all_subchannels() and
cio_reset_channel_paths() for kexec and ccw reipl. reipl_ccw_dev() now
uses reipl_find_schid() to determine the subchannel id for a given
device id.
Also remove cio_reset_channel_paths() and friends since they are not
needed anymore.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the return value of 'dasd_eer_enable' is returned - even if the
function returned '0'. Now return 'count' for successful execution.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
