fix size type errors, from uint32_t to uint16_t.
it will cause only initializes the highest 16 bits in
smu_get_atom_data_table function.
bug report:
This fixes the following static checker warning.
drivers/gpu/drm/amd/amdgpu/../powerplay/smu_v11_0.c:390 smu_v11_0_setup_pptable()
warn: passing casted pointer '&size' to 'smu_get_atom_data_table()' 32 vs 16.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to set certain power gating flags after we determine
if the firmware version is sufficient to support gfxoff.
Previously we set the pg flags in early init, but we later
we might have disabled gfxoff if the firmware versions didn't
support it. Move adding the additional pg flags after we
determine whether or not to support gfxoff.
Fixes: 005440066f ("drm/amdgpu: enable gfxoff again on raven series (v2)")
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
It's large and doesn't need contiguous memory. Fixes
allocation failures in some cases.
v2: kvfree the memory.
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The SOC15_REG_OFFSET() macro wasn't used, making the soft recovery fail.
v2: use WREG32_SOC15 instead of WREG32 + SOC15_REG_OFFSET
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This reverts commit 1a058c3376.
This interface is still in too much flux. Revert until
it's sorted out.
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 9ed2c993d7.
SET_CONFIG_REG writes to memory if register shadowing is enabled,
causing a VM fault.
NGG streamout is unstable anyway, so all UMDs should use legacy
streamout. I think Mesa is the only driver using NGG streamout.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without this pin, the csb buffer will be filled with inconsistent
data after S3 resume. And that will causes gfx hang on gfxoff
exit since this csb will be executed then.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Tested-by: Paul Gover <pmw.gover@yahoo.co.uk>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
vcn dpm on is a prerequisite for vcn power gate control.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
too frequently to update mertrics table will cause smu internal error.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before this change, the fan control state on smu_v11 was not able to be
changed because the capability check for checking if the fan control
capability existed was inverted.
[How]
The capability check for fan control in smu_v11_0_auto_fan_control was
inverted, to correctly check for the absence, instead of presence of fan
control capabilities.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VCN 2.0 firmware now requires a packet start command to be sent before
any other decode ring buffer command.
Signed-off-by: Thong Thai <thong.thai@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Sets the CMD_SOURCE bit for VCN 2.0 Decoder Ring Buffer commands. This
bit was previously set by the RBC HW on older firmware. Newer firmware
uses a SW RBC and this bit has to be set by the driver.
Signed-off-by: Thong Thai <thong.thai@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-fixes-5.3-2019-07-31:
amdgpu:
- Fix temperature granularity for navi
- Fix stable pstate setting for navi
- Fix VCN DPM enablement on navi
- Fix error handling on CS ioctl when processing dependencies
- Fix possible information leak in debugfs
amdkfd:
- fix memory alignment for VegaM
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190731191648.25729-1-alexander.deucher@amd.com
VCN should be used for Vega20 later ASICs while UVD and VCE
are for previous ASICs.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No VCN DPM bit check as that's different from VCN PG. Also
no extra check for possible double enablement/disablement
as that's already done by VCN.
v2: check return value of smu_feature_set_enabled
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commonly used for VCN powergate status retrieval for SW SMU.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable VCN powergate status report on Raven.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VCN is widely used in new ASICs and different from tranditional
UVD and VCE.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Coccinelle reports a path that the array "data" is never initialized.
The path skips the checks in the conditional branches when either
of callback functions, read_wave_vgprs and read_wave_sgprs, is not
registered. Later, the uninitialized "data" array is read
in the while-loop below and passed to put_user().
Fix the path by allocating the array with kcalloc().
The patch is simplier than adding a fall-back branch that explicitly
calls memset(data, 0, ...). Also it does not need the multiplication
1024*sizeof(*data) as the size parameter for memset() though there is
no risk of integer overflow.
Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We always need to drop the ctx reference and should check
for errors first and then dereference the fence pointer.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DPM state relates are not supported on the new SW SMU ASICs. But still
it's not OK to trigger null pointer dereference on accessing them.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The PCI revision id determines the sku.
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
in this patch,
drm/amd/powerplay: add callback function of get_thermal_temperature_range
the driver missed temperature granularity change on other temperature.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. the thermal temperature is asic related data, move the code logic to
xxx_ppt.c.
2. replace data structure PP_TemperatureRange with
smu_temperature_range.
3. change temperature uint from temp*1000 to temp (temperature uint).
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was missed during the addition of VegaM support
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hi Linus,
Please, pull the following patches that mark switch cases where we are
expecting to fall through. These patches are part of the ongoing efforts
to enable -Wimplicit-fallthrough. Most of them have been baking in linux-next
for a whole development cycle.
Also, pull the Makefile patch that globally enables the
-Wimplicit-fallthrough option.
Finally, some missing-break fixes that have been tagged for -stable:
- drm/amdkfd: Fix missing break in switch statement
- drm/amdgpu/gfx10: Fix missing break in switch statement
Notice that with these changes, we completely get rid of all the
fall-through warnings in the kernel.
Thanks
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
-----BEGIN PGP SIGNATURE-----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=J2sO
-----END PGP SIGNATURE-----
Merge tag 'Wimplicit-fallthrough-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull Wimplicit-fallthrough enablement from Gustavo A. R. Silva:
"This marks switch cases where we are expecting to fall through, and
globally enables the -Wimplicit-fallthrough option in the main
Makefile.
Finally, some missing-break fixes that have been tagged for -stable:
- drm/amdkfd: Fix missing break in switch statement
- drm/amdgpu/gfx10: Fix missing break in switch statement
With these changes, we completely get rid of all the fall-through
warnings in the kernel"
* tag 'Wimplicit-fallthrough-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
Makefile: Globally enable fall-through warning
drm/i915: Mark expected switch fall-throughs
drm/amd/display: Mark expected switch fall-throughs
drm/amdkfd/kfd_mqd_manager_v10: Avoid fall-through warning
drm/amdgpu/gfx10: Fix missing break in switch statement
drm/amdkfd: Fix missing break in switch statement
perf/x86/intel: Mark expected switch fall-throughs
mtd: onenand_base: Mark expected switch fall-through
afs: fsclient: Mark expected switch fall-throughs
afs: yfsclient: Mark expected switch fall-throughs
can: mark expected switch fall-throughs
firewire: mark expected switch fall-throughs
drm-fixes-5.3-2019-07-24:
amdgpu:
- RAS fixes for vega20
- Navi VCN fix
- DC audio fixes
- DC DSC fixes
- DC dongle fixes
- DC clk mgr fixes
- Fix DDC lines on some RV2 boards
- GDS fixes for compute
- Navi SMU fixes
ttm:
- Use the same attributes when freeing d_page->vaddr
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190724210527.3415-1-alexander.deucher@amd.com
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable -Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In preparation to enabling -Wimplicit-fallthrough, this patch silences
the following warning:
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_mqd_manager_v10.c: In function ‘mqd_manager_init_v10’:
./include/linux/dynamic_debug.h:122:52: warning: this statement may fall through [-Wimplicit-fallthrough=]
#define __dynamic_func_call(id, fmt, func, ...) do { \
^
./include/linux/dynamic_debug.h:143:2: note: in expansion of macro ‘__dynamic_func_call’
__dynamic_func_call(__UNIQUE_ID(ddebug), fmt, func, ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~
./include/linux/dynamic_debug.h:153:2: note: in expansion of macro ‘_dynamic_func_call’
_dynamic_func_call(fmt, __dynamic_pr_debug, \
^~~~~~~~~~~~~~~~~~
./include/linux/printk.h:336:2: note: in expansion of macro ‘dynamic_pr_debug’
dynamic_pr_debug(fmt, ##__VA_ARGS__)
^~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_mqd_manager_v10.c:432:3: note: in expansion of macro ‘pr_debug’
pr_debug("%s@%i\n", __func__, __LINE__);
^~~~~~~~
drivers/gpu/drm/amd/amdgpu/../amdkfd/kfd_mqd_manager_v10.c:433:2: note: here
case KFD_MQD_TYPE_COMPUTE:
^~~~
by removing the call to pr_debug() in KFD_MQD_TYPE_CP:
"The mqd init for CP and COMPUTE will have the same routine." [1]
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
[1] https://lore.kernel.org/lkml/c735a1cc-a545-50fb-44e7-c0ad93ee8ee7@amd.com/
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Add missing break statement in order to prevent the code from falling
through to case AMDGPU_IRQ_STATE_ENABLE.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: a644d85a5c ("drm/amdgpu: add gfx v10 implementation (v10)")
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Add missing break statement in order to prevent the code from falling
through to case CHIP_NAVI10.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: 14328aa58c ("drm/amdkfd: Add navi10 support to amdkfd. (v3)")
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
[Why]
In an effort to stop redundant calls to dce110_disable_audio_stream
the audio->enabled flag was added to the audio resource struct. While
this state probably shouldn't have been tracked on the audio struct
itself it still works fine for some sequences.
However, it does not work for cases where we're freeing the audio
resource (such as hotplugs) or when dynamic audio is enabled.
In these cases the pipe_ctx->stream_res.audio = NULL before we can
set audio->enabled = false. The next time we acquire the audio resource
such as on hotplug the audio will not be enabled for the stream since
DC thinks it's still enabled.
Audio state tracking should cover this sequence.
[How]
Set audio->enabled = false at the start as long as we have
pipe_ctx->stream_res.audio.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On vega20, there is an SMU message to query it. On navi, it's fetched
from the metrics table.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2:
add function smu_default_set_performance_level as default dpm level handler.
change function name smu_set_performance_level to smu_asic_set_performance_level
v1:
1.NAVI10_PEAK_SCLK_XTX 1830 Mhz
2.NAVI10_PEAK_SCLK_XT 1755 Mhz
3.NAVI10_PEAK_SCLK_XL 1625 Mhz
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
nouveau:
- bugfixes + TU116 enabling (minor iteration):w
amdgpu:
- large pile of fixes for new hw support this release (navi, vega20)
- audio hotplug fix
- bunch of corner cases and small fixes all over for amdgpu/kfd
komeda:
- back out some new properties (from this merge window) that needs
more pondering.
bochs: fb pitch setup
... plus a new panel quirk
-----BEGIN PGP SIGNATURE-----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=s190
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-07-19' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Daniel Vetter:
"Dave is back in shape, but now family got it so I'm doing the pull.
Two things worthy of note:
- nouveau feature pull was way too late, Dave&me decided to not take
that, so Ben spun up a pull with just the fixes.
- after some chatting with the arm display maintainers we decided to
change a bit how that's maintained, for more oversight/review and
cross vendor collab.
More details below:
nouveau:
- bugfixes
- TU116 enabling (minor iteration) :w
amdgpu:
- large pile of fixes for new hw support this release (navi, vega20)
- audio hotplug fix
- bunch of corner cases and small fixes all over for amdgpu/kfd
komeda:
- back out some new properties (from this merge window) that needs
more pondering.
bochs:
- fb pitch setup
core:
- a new panel quirk
- misc fixes"
* tag 'drm-next-2019-07-19' of git://anongit.freedesktop.org/drm/drm: (73 commits)
drm/nouveau/secboot/gp102-: remove WAR for SEC2 RTOS start bug
drm/nouveau/flcn/gp102-: improve implementation of bind_context() on SEC2/GSP
drm/nouveau: fix memory leak in nouveau_conn_reset()
drm/nouveau/dmem: missing mutex_lock in error path
drm/nouveau/hwmon: return EINVAL if the GPU is powered down for sensors reads
drm/nouveau: fix bogus GPL-2 license header
drm/nouveau: fix bogus GPL-2 license header
drm/nouveau/i2c: Enable i2c pads & busses during preinit
drm/nouveau/disp/tu102-: wire up scdc parameter setter
drm/nouveau/core: recognise TU116 chipset
drm/nouveau/kms: disallow dual-link harder if hdmi connection detected
drm/nouveau/disp/nv50-: fix center/aspect-corrected scaling
drm/nouveau/disp/nv50-: force scaler for any non-default LVDS/eDP modes
drm/nouveau/mcp89/mmu: Use mcp77_mmu_new instead of g84_mmu_new on MCP89.
drm/amd/display: init res_pool dccg_ref, dchub_ref with xtalin_freq
drm/amdgpu/pm: remove check for pp funcs in freq sysfs handlers
drm/amd/display: Force uclk to max for every state
drm/amdkfd: Remove GWS from process during uninit
drm/amd/amdgpu: Fix offset for vmid selection in debugfs interface
drm/amd/powerplay: update vega20 driver if to fit latest SMU firmware
...
[Why]:
Some active dongles have DP++ port and DP port at the same time. Current
code doesn't cover DP++ case and processes as default DVI case, in which
audio is disabled. Because of dual mode, DP case is also treat as DVI case
for the other port.
[How]:
According DP 1.4 spec, add DP++ procedure similar with HDMI case. Also
add None dongle type for DP case.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously assume eDP sink present if connector present. Do not
need to enforce this restriction. Fix issue where driver attempt
to read link setting even though no edp connected.
{How]
Only read link setting after reading connection status.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The audios array defined in "struct resource_pool" is only 6 (MAX_PIPES)
but the max number of audio devices (num_audio) is 7. In some projects,
it will run out of audios array.
[How]
Incraese the audios array size to 7.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For boards that support eDP but do not have a physical eDP
display connected an ASSERT will be thrown. This is not a
critical failure and shouldn't be treated as such.
[How]
Drop the assertion.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dm_helpers_parse_edid_caps, there is a corner case where no speakers
can be allocated even though the audio mode count is greater than 0.
Enabling audio when no speaker allocations exists can cause issues in
the video stream.
[How]
Add a check to not enable audio unless one or more speaker allocations
exist (since doing this can cause issues in the video stream).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is possible (but very unlikely) that constructing dc fails
before current_state is created.
We support 666 color depth in some scenarios, but this
isn't handled in get_norm_pix_clk. It uses exactly the
same pixel clock as the 888 case.
[How]
Check for non null current_state before destructing.
Add case for 666 color depth to get_norm_pix_clk to
avoid assertion.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver will create 0, 1, and 2 ddc engines for RV2,
but some platforms used 0, 1, and 3.
[How]
Still allocate 4 ddc engines for RV2.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot optimization removed proper front end power off sequence.
In driver disable enable case, this causes driver to power gate hubp
and dpp while there is still memory fetching going on, this can cause
invalid memory requests to be generated which will hang data fabric.
[How]
Put back proper front end power off sequence
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In pipe split issue occurs when we program immediate flip while vsync flip is pending
[how]
Don't program immediate flip until flip is no longer pending
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some display's hsync width is lower than the minimum dcn20 is set
to support right now. This will cause optc1_validate_timing to fail which
eventually will result in wrong set mode. This was set to 8 as per
HW team's request for no valid reason.
[How]
Changing min_h_sync_width to 4 will let us validate timing for
preffered mode and light up the headset. This change was made
to Vega 10 before for a similar issue.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some platforms, the encoder id 3 is not populated. So the encoders
are not stored in right order as index (id: 0, 1, 2, 4, 5) at pool. This
would cause encoders id 4 & id 5 to fail when finding corresponding
audio device, defaulting to the first available audio device. As result,
we cannot stream audio into two DP ports with encoders id 4 & id 5.
[How]
It need to create enough audio device objects (0 - 5) to perform matching.
Then use encoder engine id to find matched audio device.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When the system is going into suspend, set_backlight gets called
after the eDP got blanked. Since smooth brightness is enabled,
the driver will make a call into the DMCU to ramp the brightness.
The DMCU would try to enable ABM to do so. But since the display is
blanked, this ends up causing ABM1_ACE_DBUF_REG_UPDATE_PENDING to
get stuck at 1, which results in a dead lock in the DMCU firmware.
[how]
Disable brightness ramping when the eDP display is blanked.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we recover from hang, we do not want to skip the audio enable call.
[How]
Disable audio in dc_reinitialize_hardware
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When launch D10.2, driver will write DPCD 0x107 with 0x00
[How]
Read MAX_DOWNSPREAD (0x0003h) then keep in current
link settings
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
