Commit Graph

1122 Commits

Author SHA1 Message Date
Deepak K
0003450964 omap2/3/4: serial: errata i202: fix for MDR1 access
Errata i202 (OMAP3430 - 1.12, OMAP3630 - 1.6):
UART module MDR1 register access can cause a dummy underrun
condition which could result in a freeze in the case of IrDA
communication or if used as UART, corrupted data.

Workaround is as follows for everytime MDR1 register is changed:
* setup all required UART registers
* setup MDR1.MODE_SELECT bit field
* Wait 5 L4 clk cycles + 5 UART functional clock cycles
* Clear the Tx and RX fifo using FCR register

Note: The following step is not done as I am assuming it is not
needed due to reconfiguration being done and there is no halted
operation perse.
* Read if required, the RESUME register to resume halted operation

Based on an earlier patch at:
http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=42d4a342c009bd9727c100abc8a4bc3063c22f0c

Signed-off-by: Deepak K <deepak.k@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:12 +03:00
Nishanth Menon
5a927b36f5 omap2/3/4: serial: introduce errata handling
introduce silicon specific quirks as a errata handling mechanism

as a start UART_ERRATA_FIFO_FULL_ABORT is used to handle the override
for fifo full condition for rx and tx.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:12 +03:00
Nishanth Menon
bfe6977ac7 omap2/3/4: serial: kill dev_attr_sleep_timeout sparse warn
Remove the following sparse warnings by declaring attr as static:
arch/arm/mach-omap2/serial.c:627:1: warning: symbol 'dev_attr_sleep_timeout'
was not declared. Should it be static?

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:12 +03:00
Nishanth Menon
c54bae1f06 omap2/3/4: serial: remove initialization sparse warnings
Initialization of pointer should be done with NULL. Removes sparse
warnings:
arch/arm/mach-omap2/serial.c:566:17: warning: Using plain integer as NULL pointer
arch/arm/mach-omap2/serial.c:567:17: warning: Using plain integer as NULL pointer

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:11 +03:00
Govindraj R
5ade4ff593 omap3: serial: Add context save and restore for mcr
Adds context save/restore for mcr register as state of mcr register
is lost after core off.

Signed-off-by: Govindraj R <govindraj.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:11 +03:00
David Anders
b075f58b2c omap4: Add OMAP4 Panda Support
Add initial support for the OMAP4 based Panda Board.

Signed-off-by: David Anders <x0132446@ti.com>
[tony@atomide.com: selected board by default in Kconfig]
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:05 +03:00
Hemanth V
509b6d9314 OMAP4: Add GPIO LED support for SDP board
This patch adds support for GPIO LEDs present on OMAP4
SDP and Blaze boards. This basically adds platform data
required by leds-gpio driver

Signed-off-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:04 +03:00
Shubhrajyoti Datta
83078f9bdc omap4: Board changes for 4430sdp tmp105 temperature sensor
Adding board configuration for the tmp105
temperature sensor. The interface to the sensor
is I2C.

Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:04 +03:00
Santosh Shilimkar
5026391c2a omap4: mmc: Fix the regulator resource for MMC2 on 4430sdp
The MMC1 and MMC2 cards have seperate LDO supplies. Current code assumes
that they are powered by same LDO.

This patch fixes the same and has VAUX1 as supply to MMC2 card.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:03 +03:00
Mathias Nyman
70b5d7377e omap: tsl2563 ALS support for Nokia N900
This commit will enable usage of tsl2563 ambient light sensor on Nokia N900.

Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:03 +03:00
Jarkko Nikula
64d0669182 omap: rx51: Add supply and data for the tpa6130a2 headphoneamplifier
With these and upcoming change to tpa6130a2 driver it's possible to add
support for the TPA6130A2 headphone amplifier.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:03 +03:00
Jarkko Nikula
5c7d9bbec6 omap: rx51: Use REGULATOR_SUPPLY macro when initializingregulator consumers
There is REGULATOR_SUPPLY macro available for initializing the struct
regulator_consumer_supply so use it where applicable (all other supplies
than vdds_sdi) as it improves the readability.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:02 +03:00
Jarkko Nikula
87581fd4a9 omap: rx51: Add platform_data for tlv320aic3x with reset gpionumber
Proper operation of the tlv320aic3x audio codec requires that reset
sequencing is done in pair with supply voltages when using the regulator
framework. Add the codec reset gpio used in Nokia RX51 to tlv320aic3x
data.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:02 +03:00
Jarkko Nikula
000d534ed7 omap: rx51: Set regulator V28 always on
It seems that the battery cover sensor in Nokia N900 is powered from the
V28 domain. Now if this regulator is disabled it causes that the gpio 160
reads only zero which effectively causes uSD removal detection.

Currently the bootloader enabled V28 is kept on but this may change in the
future according to comment in
drivers/regulator/core.c: regulator_has_full_constraints.

Also if there are any consumers on the V28 domain doing regulator_enable
regulator_disable cycle the V28 will be disabled after that.

Prepare for these by defining the V28 as always_on regulator.

Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:02 +03:00
Grazvydas Ignotas
79ccf549b3 omap3: pandora: add NAND and wifi support
Add platform data for NAND and wifi, also setup all GPIOs
needed to use the wifi chip.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:01 +03:00
Grazvydas Ignotas
ad74db6041 omap3: pandora: update gpio-keys data
Update gpio-keys setup so it matches what is on default firmware.
Also make use of debounce feature in gpio-keys instead of setting it
explicitly, as gpio-keys is now capable of using hardware debounce on
OMAPs thanks to recent gpiolib changes.
Also fix a sparce warning along the way.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:01 +03:00
Ohad Ben-Cohen
c3777c19d2 omap: zoom3: wlan board muxing
Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM3.

Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:00 +03:00
Ohad Ben-Cohen
7b2308cfc9 omap: zoom2: wlan board muxing
Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM2.

Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-08-02 13:18:00 +03:00
Thomas Weber
0cbe70eeaa OMAP2: Devkit8000: Fix regulator for power supply
Devkit8000 uses the TPS65930 and not the TWL4030.
The TPS65930 uses only a subset of the power supplies
of the TWL4030.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:04:42 +03:00
Thomas Weber
a34664ded7 OMAP2: Devkit8000: Remove unused omap_board_config
omap_board_config is no longer used and thats why empty.
This patch removes the empty omap_board_config.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:04:42 +03:00
Thomas Weber
09c0721e60 OMAP2: Devkit8000: Using gpio_is_valid macro
Using the macro gpio_is_valid for check of valid gpio pins.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:04:42 +03:00
Thomas Weber
1f489f9eac OMAP2: Devkit8000: Using the REGULATOR_SUPPLY macro
Replacing supplies with the REGULATOR_SUPPLY macro.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:04:41 +03:00
Thomas Weber
e185469be0 OMAP2: Devkit8000: Remove en-/disable for tv panel
devkit8000_panel_enable_tv and devkit8000_panel_disable_tv are already
done in DSS2 code. So they are no longer needed in board code.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:04:41 +03:00
Thomas Weber
612840bbd4 OMAP2: Devkit8000: Remove non existing vsim supply
The Devkit8000 uses the cost reduced variant tps65930 of the twl4030.
The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2.

vaux2 is not used on Devkit8000.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:04:41 +03:00
Thomas Weber
a7707a335a OMAP2: Devkit8000: Remove unneeded VDVI supply
The VDVI power supply is no longer needed in
board code with the new DSS2 interface.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:04:41 +03:00
Kan-Ru Chen
4098609898 OMAP2: Devkit8000: Setup LCD reset
This patch corrects the LCD reset pin configuration.

Original code from early devkit8000 patch sets the TWL4030 GPIO_1
to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
disabled when other display is turned on.

Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:04:40 +03:00
Kan-Ru Chen
31c73f74f3 OMAP2: Devkit8000: Enable DVI-D output
This patch corrects the DVI-D output setup of Devkit8000

Devkit8000 has different DVI reset pin with the BeagleBoard.
On Devkit8000 the TWL4030 GPIO_7 is assigned to do the job.

Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:04:40 +03:00
Thomas Weber
61d07ef4b4 OMAP2: Devkit8000: change panel to generic panel
Choose the generic panel for lcd code of Devkit8000.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:04:40 +03:00
Thomas Weber
5fd58b5103 OMAP2: Devkit8000: Cleanup for power supplies
Corrected the wrong power supplies in devkit8000 code.

Add supply for ads7846 to support the new regulator framework for
touchscreen.

Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:04:39 +03:00
Christoph Egger
847e951b99 Removing dead MACH_OMAP2_H4_USB1
MACH_OMAP2_H4_USB1 doesn't exist in Kconfig, therefore removing all
references for it from the source code.

Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:03:59 +03:00
Christoph Egger
267ecec95f Removing dead MACH_OMAP_H4_OTG
MACH_OMAP_H4_OTG doesn't exist in Kconfig, therefore removing all
references for it from the source code.

Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:03:59 +03:00
Christoph Egger
df8d481df9 Removing dead OMAP_STI
OMAP_STI doesn't exist in Kconfig, therefore removing all
references for it from the source code.

Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 17:03:58 +03:00
Christoph Egger
4705c1ca8b Removing dead OMAP_IR
OMAP_IR doesn't exist in Kconfig, therefore removing all references
for it from the source code.

Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated for new mux code]
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:53 +03:00
Tony Lindgren
8d9166b519 omap2/3/4: Add Kconfig option to compile in typical omap features
This produces a sane config that's suitable for using as the
base for most omap2/3/4 boards.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:48 +03:00
Tony Lindgren
ffb63e3402 omap2/3/4: Select all omaps and boards by default
Select all omaps and boards by default

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:47 +03:00
Tony Lindgren
68ac8f7dda omap2/3/4: Move Kconfig options to mach-omap2/Kconfig
Move omap2/3/4 specific Kconfig options to mach-omap2/Kconfig

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:47 +03:00
Tony Lindgren
4a54db6124 omap: Make omap specific features appear under Kconfig menu
This will make Kconfig look nicer for selecting omap processor type

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:47 +03:00
Tony Lindgren
c9d8230e31 omap: mux: Remove old mux code
All mach-omap2 omaps should now use the new mux code.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:40 +03:00
Tony Lindgren
f99bf16d70 omap: mux: Convert 2420 platform init code to use new mux code
Convert 2420 platform init code to use new mux code

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:40 +03:00
Tony Lindgren
58310acd3a omap: mux: Mux 2430 USB0HS_STP in board-2430.c
Use new mux functions for that. There are no other known 2430 boards
that need this mux.

Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:39 +03:00
Tony Lindgren
18dbe6c5dd omap: mux: Mux Apollon LCD power in board-apollon.c
Use the new mux function for that.

Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:39 +03:00
Tony Lindgren
93c43f2561 omap: mux: Do keypad muxing in board-*.c files
This way we get pin muxing out of plat-omap and can convert H4 to use the
new mux functions.

Note that it should be safe to assume we can mux all the keypad pins
except on H4 which may have Menelaus connected.

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:39 +03:00
Tony Lindgren
0d600ff6fe omap: mux: Make omap2 FS USB code use new mux functions
Make omap2 FS USB code use new mux functions. Do not mux usb2_tllse0
as it has multiple options.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:38 +03:00
Tony Lindgren
369ed78fc9 omap: mux: Select POP package for 2430SDP
Select POP package for 2430SDP

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:38 +03:00
Tony Lindgren
bd8f0fc979 omap: mux: Select POP package for N8X0
Select POP package for N8X0

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:38 +03:00
Tony Lindgren
b52b14ef0d omap: mux: Select POP package for Apollon
Select POP package for Apollon

Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:37 +03:00
Tony Lindgren
23275d459e omap: mux: Select SIP package for H4
Select SIP package for H4

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:37 +03:00
Tony Lindgren
89ba109229 omap: mux: Add data for 2430
Add data for 2430. Big thanks to Paul Walmsley <paul@pwsan.com>
for generating usable mux data out of TRMs.

Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:36 +03:00
Tony Lindgren
fc44046167 omap: mux: Add data for 2420
Add data for 2420. Big thanks to Paul Walmsley <paul@pwsan.com>
for generating usable mux data out of TRMs.

Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:36 +03:00
Tony Lindgren
ac1c94fb85 omap: mux: Remove unncessary parens from mux34xx.c
Remove unncessary parens from mux34xx.c

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-07-05 16:31:36 +03:00