The logic in rt6_age_examine_exception is confusing. The commit is
to refactor the code.
Signed-off-by: Xu Jia <xujia39@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The series of space has been replaced by tab space
wherever required.
Signed-off-by: Shubhankar Kuranagatti <shubhankarvk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move generic blackhole dst ops to the core and use them from both
ipv4_dst_blackhole_ops and ip6_dst_blackhole_ops where possible. No
functional change otherwise. We need these also in other locations
and having to define them over and over again is not great.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the value '2' to 'fib_notify_on_flag_change' to allow sending
notifications only for failed route installation.
Separate value is added for such notifications because there are less of
them, so they do not impact performance and some users will find them more
important.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel, but not
necessarily in hardware.
The asynchronous nature of route installation in hardware can lead to a
routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
To avoid such cases, previous patch set added the ability to emit
RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed, this behavior is controlled by sysctl.
With the above mentioned behavior, it is possible to know from user-space
if the route was offloaded, but if the offload fails there is no indication
to user-space. Following a failure, a routing daemon will wait indefinitely
for a notification that will never come.
This patch adds an "offload_failed" indication to IPv6 routes, so that
users will have better visibility into the offload process.
'struct fib6_info' is extended with new field that indicates if route
offload failed. Note that the new field is added using unused bit and
therefore there is no need to increase struct size.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes the errores reported when building for powerpc:
ERROR: modpost: "ip6_dst_check" [vmlinux] is a static EXPORT_SYMBOL
ERROR: modpost: "ipv4_dst_check" [vmlinux] is a static EXPORT_SYMBOL
ERROR: modpost: "ipv4_mtu" [vmlinux] is a static EXPORT_SYMBOL
ERROR: modpost: "ip6_mtu" [vmlinux] is a static EXPORT_SYMBOL
Fixes: f67fbeaebd ("net: use indirect call helpers for dst_mtu")
Fixes: bbd807dfbf ("net: indirect call helpers for ipv4/ipv6 dst_check functions")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Link: https://lore.kernel.org/r/20210204181839.558951-2-brianvv@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip6_dst_check and ipv4_dst_check
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch avoids the indirect call for the common case:
ip6_mtu and ipv4_mtu
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel,
but not necessarily in hardware.
The asynchronous nature of route installation in hardware can lead
to a routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
It is also possible for a route already installed in hardware to change
its action and therefore its flags. For example, a host route that is
trapping packets can be "promoted" to perform decapsulation following
the installation of an IPinIP/VXLAN tunnel.
Emit RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed. The aim is to provide an indication to user-space
(e.g., routing daemons) about the state of the route in hardware.
Introduce a sysctl that controls this behavior.
Keep the default value at 0 (i.e., do not emit notifications) for several
reasons:
- Multiple RTM_NEWROUTE notification per-route might confuse existing
routing daemons.
- Convergence reasons in routing daemons.
- The extra notifications will negatively impact the insertion rate.
- Not all users are interested in these notifications.
Move fib6_info_hw_flags_set() to C file because it is no longer a short
function.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For IPv4, default route is learned via DHCPv4 and user is allowed to change
metric using config etc/network/interfaces. But for IPv6, default route can
be learned via RA, for which, currently a fixed metric value 1024 is used.
Ideally, user should be able to configure metric on default route for IPv6
similar to IPv4. This patch adds sysctl for the same.
Logs:
For IPv4:
Config in etc/network/interfaces:
auto eth0
iface eth0 inet dhcp
metric 4261413864
IPv4 Kernel Route Table:
$ ip route list
default via 172.21.47.1 dev eth0 metric 4261413864
FRR Table, if a static route is configured:
[In real scenario, it is useful to prefer BGP learned default route over DHCPv4 default route.]
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, P - PIM, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
> - selected route, * - FIB route
S>* 0.0.0.0/0 [20/0] is directly connected, eth0, 00:00:03
K 0.0.0.0/0 [254/1000] via 172.21.47.1, eth0, 6d08h51m
i.e. User can prefer Default Router learned via Routing Protocol in IPv4.
Similar behavior is not possible for IPv6, without this fix.
After fix [for IPv6]:
sudo sysctl -w net.ipv6.conf.eth0.net.ipv6.conf.eth0.ra_defrtr_metric=1996489705
IP monitor: [When IPv6 RA is received]
default via fe80::xx16:xxxx:feb3:ce8e dev eth0 proto ra metric 1996489705 pref high
Kernel IPv6 routing table
$ ip -6 route list
default via fe80::be16:65ff:feb3:ce8e dev eth0 proto ra metric 1996489705 expires 21sec hoplimit 64 pref high
FRR Table, if a static route is configured:
[In real scenario, it is useful to prefer BGP learned default route over IPv6 RA default route.]
Codes: K - kernel route, C - connected, S - static, R - RIPng,
O - OSPFv3, I - IS-IS, B - BGP, N - NHRP, T - Table,
v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
> - selected route, * - FIB route
S>* ::/0 [20/0] is directly connected, eth0, 00:00:06
K ::/0 [119/1001] via fe80::xx16:xxxx:feb3:ce8e, eth0, 6d07h43m
If the metric is changed later, the effect will be seen only when next IPv6
RA is received, because the default route must be fully controlled by RA msg.
Below metric is changed from 1996489705 to 1996489704.
$ sudo sysctl -w net.ipv6.conf.eth0.ra_defrtr_metric=1996489704
net.ipv6.conf.eth0.ra_defrtr_metric = 1996489704
IP monitor:
[On next IPv6 RA msg, Kernel deletes prev route and installs new route with updated metric]
Deleted default via fe80::xx16:xxxx:feb3:ce8e dev eth0 proto ra metric 1996489705 expires 3sec hoplimit 64 pref high
default via fe80::xx16:xxxx:feb3:ce8e dev eth0 proto ra metric 1996489704 pref high
Signed-off-by: Praveen Chaudhary <pchaudhary@linkedin.com>
Signed-off-by: Zhenggen Xu <zxu@linkedin.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210125214430.24079-1-pchaudhary@linkedin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds an IPv6 routes encapsulation attribute
to the result of netlink RTM_GETROUTE requests
(i.e. ip route get 2001:db8::).
Signed-off-by: Oliver Herms <oliver.peter.herms@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201118230651.GA8861@tws
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove in-kernel route notifications when the configuration of their
nexthop changes.
These notifications are unnecessary because the route still uses the
same nexthop ID. A separate notification for the nexthop change itself
is now sent in the nexthop notification chain.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a ICMPV6_PKT_TOOBIG report a next-hop MTU that is less than the IPv6
minimum link MTU, the estimated path MTU is reduced to the minimum link
MTU. This behaviour breaks TAHI IPv6 Core Conformance Test v6LC4.1.6:
Packet Too Big Less than IPv6 MTU.
Referring to RFC 8201 section 4: "If a node receives a Packet Too Big
message reporting a next-hop MTU that is less than the IPv6 minimum link
MTU, it must discard it. A node must not reduce its estimate of the Path
MTU below the IPv6 minimum link MTU on receipt of a Packet Too Big
message."
Drop the path MTU update if reported MTU is less than the minimum link MTU.
Signed-off-by: Georg Kohmann <geokohma@cisco.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable err is being initialized with a value that is never read and
it is being updated later with a new value. The initialization is redundant
and can be removed. Also re-order variable declarations in reverse
Christmas tree ordering.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_info_create() invokes nexthop_get(), which increases the
refcount of the "nh".
When ip6_route_info_create() returns, local variable "nh" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
ip6_route_info_create(). When nexthops can not be used with source
routing, the function forgets to decrease the refcnt increased by
nexthop_get(), causing a refcnt leak.
Fix this issue by pulling up the error source routing handling when
nexthops can not be used with source routing.
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no functionality change for this patch.
Struct bpf_iter_reg is used to register a bpf_iter target,
which includes information for both prog_load, link_create
and seq_file creation.
This patch puts fields related seq_file creation into
a different structure. This will be useful for map
elements iterator where one iterator covers different
map types and different map types may have different
seq_ops, init/fini private_data function and
private_data size.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723184109.590030-1-yhs@fb.com
One additional field btf_id is added to struct
bpf_ctx_arg_aux to store the precomputed btf_ids.
The btf_id is computed at build time with
BTF_ID_LIST or BTF_ID_LIST_GLOBAL macro definitions.
All existing bpf iterators are changed to used
pre-compute btf_ids.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200720163403.1393551-1-yhs@fb.com
Thomas reported a regression with IPv6 and anycast using the following
reproducer:
echo 1 > /proc/sys/net/ipv6/conf/all/forwarding
ip -6 a add fc12::1/16 dev lo
sleep 2
echo "pinging lo"
ping6 -c 2 fc12::
The conversion of addrconf_f6i_alloc to use ip6_route_info_create missed
the use of fib6_is_reject which checks addresses added to the loopback
interface and sets the REJECT flag as needed. Update fib6_is_reject for
loopback checks to handle RTF_ANYCAST addresses.
Fixes: c7a1ce397a ("ipv6: Change addrconf_f6i_alloc to use ip6_route_info_create")
Reported-by: thomas.gambier@nexedi.com
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brian reported a crash in IPv6 code when using rpfilter with a setup
running FRR and external nexthop objects. The root cause of the crash
is fib6_select_path setting fib6_nh in the result to NULL because of
an improper check for nexthop objects.
More specifically, rpfilter invokes ip6_route_lookup with flowi6_oif
set causing fib6_select_path to be called with have_oif_match set.
fib6_select_path has early check on have_oif_match and jumps to the
out label which presumes a builtin fib6_nh. This path is invalid for
nexthop objects; for external nexthops fib6_select_path needs to just
return if the fib6_nh has already been set in the result otherwise it
returns after the call to nexthop_path_fib6_result. Update the check
on have_oif_match to not bail on external nexthops.
Update selftests for this problem.
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Reported-by: Brian Rak <brak@choopa.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that a considerable amount of cycles were spent on the
expensive indirect calls on fib6_rule_lookup. This patch introduces an
inline helper called pol_route_func that uses the indirect_call_wrappers
to avoid the indirect calls.
This patch saves around 50ns per call.
Performance was measured on the receiver by checking the amount of
syncookies that server was able to generate under a synflood load.
Traffic was generated using trafgen[1] which was pushing around 1Mpps on
a single queue. Receiver was using only one rx queue which help to
create a bottle neck and make the experiment rx-bounded.
These are the syncookies generated over 10s from the different runs:
Whithout the patch:
TcpExtSyncookiesSent 3553749 0.0
TcpExtSyncookiesSent 3550895 0.0
TcpExtSyncookiesSent 3553845 0.0
TcpExtSyncookiesSent 3541050 0.0
TcpExtSyncookiesSent 3539921 0.0
TcpExtSyncookiesSent 3557659 0.0
TcpExtSyncookiesSent 3526812 0.0
TcpExtSyncookiesSent 3536121 0.0
TcpExtSyncookiesSent 3529963 0.0
TcpExtSyncookiesSent 3536319 0.0
With the patch:
TcpExtSyncookiesSent 3611786 0.0
TcpExtSyncookiesSent 3596682 0.0
TcpExtSyncookiesSent 3606878 0.0
TcpExtSyncookiesSent 3599564 0.0
TcpExtSyncookiesSent 3601304 0.0
TcpExtSyncookiesSent 3609249 0.0
TcpExtSyncookiesSent 3617437 0.0
TcpExtSyncookiesSent 3608765 0.0
TcpExtSyncookiesSent 3620205 0.0
TcpExtSyncookiesSent 3601895 0.0
Without the patch the average is 354263 pkt/s or 2822 ns/pkt and with
the patch the average is 360738 pkt/s or 2772 ns/pkt which gives an
estimate of 50 ns per packet.
[1] http://netsniff-ng.org/
Changelog since v1:
- Change ordering in the ICW (Paolo Abeni)
Cc: Luigi Rizzo <lrizzo@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces ecmp nexthops and nexthop groups
for mac fdb entries. In subsequent patches this is used
by the vxlan driver fdb entries. The use case is
E-VPN multihoming [1,2,3] which requires bridged vxlan traffic
to be load balanced to remote switches (vteps) belonging to
the same multi-homed ethernet segment (This is analogous to
a multi-homed LAG but over vxlan).
Changes include new nexthop flag NHA_FDB for nexthops
referenced by fdb entries. These nexthops only have ip.
This patch includes appropriate checks to avoid routes
referencing such nexthops.
example:
$ip nexthop add id 12 via 172.16.1.2 fdb
$ip nexthop add id 13 via 172.16.1.3 fdb
$ip nexthop add id 102 group 12/13 fdb
$bridge fdb add 02:02:00:00:00:13 dev vxlan1000 nhid 101 self
[1] E-VPN https://tools.ietf.org/html/rfc7432
[2] E-VPN VxLAN: https://tools.ietf.org/html/rfc8365
[3] LPC talk with mention of nexthop groups for L2 ecmp
http://vger.kernel.org/lpc_net2018_talks/scaling_bridge_fdb_database_slidesV3.pdf
v4 - fixed uninitialized variable reported by kernel test robot
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for better compat ioctl handling by moving the user copy out
of ipv6_route_ioctl.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-05-14
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Merged tag 'perf-for-bpf-2020-05-06' from tip tree that includes CAP_PERFMON.
2) support for narrow loads in bpf_sock_addr progs and additional
helpers in cg-skb progs, from Andrey.
3) bpf benchmark runner, from Andrii.
4) arm and riscv JIT optimizations, from Luke.
5) bpf iterator infrastructure, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b121b341e5 ("bpf: Add PTR_TO_BTF_ID_OR_NULL
support") adds a field btf_id_or_null_non0_off to
bpf_prog->aux structure to indicate that the
first ctx argument is PTR_TO_BTF_ID reg_type and
all others are PTR_TO_BTF_ID_OR_NULL.
This approach does not really scale if we have
other different reg types in the future, e.g.,
a pointer to a buffer.
This patch enables bpf_iter targets registering ctx argument
reg types which may be different from the default one.
For example, for pointers to structures, the default reg_type
is PTR_TO_BTF_ID for tracing program. The target can register
a particular pointer type as PTR_TO_BTF_ID_OR_NULL which can
be used by the verifier to enforce accesses.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200513180221.2949882-1-yhs@fb.com
Change func bpf_iter_unreg_target() parameter from target
name to target reg_info, similar to bpf_iter_reg_target().
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200513180220.2949737-1-yhs@fb.com
Currently bpf_iter_reg_target takes parameters from target
and allocates memory to save them. This is really not
necessary, esp. in the future we may grow information
passed from targets to bpf_iter manager.
The patch refactors the code so target reg_info
becomes static and bpf_iter manager can just take
a reference to it.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200513180219.2949605-1-yhs@fb.com
This patch added netlink and ipv6_route targets, using
the same seq_ops (except show() and minor changes for stop())
for /proc/net/{netlink,ipv6_route}.
The net namespace for these targets are the current net
namespace at file open stage, similar to
/proc/net/{netlink,ipv6_route} reference counting
the net namespace at seq_file open stage.
Since module is not supported for now, ipv6_route is
supported only if the IPV6 is built-in, i.e., not compiled
as a module. The restriction can be lifted once module
is properly supported for bpf_iter.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200509175910.2476329-1-yhs@fb.com
We currently have to adjust ipv6 route gc_thresh/max_size depending
on number of cpus on a server, this makes very little sense.
If the kernels sets /proc/sys/net/ipv6/route/gc_thresh to 1024
and /proc/sys/net/ipv6/route/max_size to 4096, then we better
not track the percpu dst that our implementation uses.
Only routes not added (directly or indirectly) by the admin
should be tracked and limited.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: David Ahern <dsahern@kernel.org>
Cc: Maciej Żenczykowski <maze@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
percpu_counter_add() uses a default batch size which is quite big
on platforms with 256 cpus. (2*256 -> 512)
This means dst_entries_get_fast() can be off by +/- 2*(nr_cpus^2)
(131072 on servers with 256 cpus)
Reduce the batch size to something more reasonable, and
add logic to ip6_dst_gc() to call dst_entries_get_slow()
before calling the _very_ expensive fib6_run_gc() function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 19bda36c42:
| ipv6: add mtu lock check in __ip6_rt_update_pmtu
|
| Prior to this patch, ipv6 didn't do mtu lock check in ip6_update_pmtu.
| It leaded to that mtu lock doesn't really work when receiving the pkt
| of ICMPV6_PKT_TOOBIG.
|
| This patch is to add mtu lock check in __ip6_rt_update_pmtu just as ipv4
| did in __ip_rt_update_pmtu.
The above reasoning is incorrect. IPv6 *requires* icmp based pmtu to work.
There's already a comment to this effect elsewhere in the kernel:
$ git grep -p -B1 -A3 'RTAX_MTU lock'
net/ipv6/route.c=4813=
static int rt6_mtu_change_route(struct fib6_info *f6i, void *p_arg)
...
/* In IPv6 pmtu discovery is not optional,
so that RTAX_MTU lock cannot disable it.
We still use this lock to block changes
caused by addrconf/ndisc.
*/
This reverts to the pre-4.9 behaviour.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Fixes: 19bda36c42 ("ipv6: add mtu lock check in __ip6_rt_update_pmtu")
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-05-01 (v2)
The following pull-request contains BPF updates for your *net-next* tree.
We've added 61 non-merge commits during the last 6 day(s) which contain
a total of 153 files changed, 6739 insertions(+), 3367 deletions(-).
The main changes are:
1) pulled work.sysctl from vfs tree with sysctl bpf changes.
2) bpf_link observability, from Andrii.
3) BTF-defined map in map, from Andrii.
4) asan fixes for selftests, from Andrii.
5) Allow bpf_map_lookup_elem for SOCKMAP and SOCKHASH, from Jakub.
6) production cloudflare classifier as a selftes, from Lorenz.
7) bpf_ktime_get_*_ns() helper improvements, from Maciej.
8) unprivileged bpftool feature probe, from Quentin.
9) BPF_ENABLE_STATS command, from Song.
10) enable bpf_[gs]etsockopt() helpers for sock_ops progs, from Stanislav.
11) enable a bunch of common helpers for cg-device, sysctl, sockopt progs,
from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nik reported a bug with pcpu dst cache when nexthop objects are
used illustrated by the following:
$ ip netns add foo
$ ip -netns foo li set lo up
$ ip -netns foo addr add 2001:db8:11::1/128 dev lo
$ ip netns exec foo sysctl net.ipv6.conf.all.forwarding=1
$ ip li add veth1 type veth peer name veth2
$ ip li set veth1 up
$ ip addr add 2001:db8:10::1/64 dev veth1
$ ip li set dev veth2 netns foo
$ ip -netns foo li set veth2 up
$ ip -netns foo addr add 2001:db8:10::2/64 dev veth2
$ ip -6 nexthop add id 100 via 2001:db8:10::2 dev veth1
$ ip -6 route add 2001:db8:11::1/128 nhid 100
Create a pcpu entry on cpu 0:
$ taskset -a -c 0 ip -6 route get 2001:db8:11::1
Re-add the route entry:
$ ip -6 ro del 2001:db8:11::1
$ ip -6 route add 2001:db8:11::1/128 nhid 100
Route get on cpu 0 returns the stale pcpu:
$ taskset -a -c 0 ip -6 route get 2001:db8:11::1
RTNETLINK answers: Network is unreachable
While cpu 1 works:
$ taskset -a -c 1 ip -6 route get 2001:db8:11::1
2001:db8:11::1 from :: via 2001:db8:10::2 dev veth1 src 2001:db8:10::1 metric 1024 pref medium
Conversion of FIB entries to work with external nexthop objects
missed an important difference between IPv4 and IPv6 - how dst
entries are invalidated when the FIB changes. IPv4 has a per-network
namespace generation id (rt_genid) that is bumped on changes to the FIB.
Checking if a dst_entry is still valid means comparing rt_genid in the
rtable to the current value of rt_genid for the namespace.
IPv6 also has a per network namespace counter, fib6_sernum, but the
count is saved per fib6_node. With the per-node counter only dst_entries
based on fib entries under the node are invalidated when changes are
made to the routes - limiting the scope of invalidations. IPv6 uses a
reference in the rt6_info, 'from', to track the corresponding fib entry
used to create the dst_entry. When validating a dst_entry, the 'from'
is used to backtrack to the fib6_node and check the sernum of it to the
cookie passed to the dst_check operation.
With the inline format (nexthop definition inline with the fib6_info),
dst_entries cached in the fib6_nh have a 1:1 correlation between fib
entries, nexthop data and dst_entries. With external nexthops, IPv6
looks more like IPv4 which means multiple fib entries across disparate
fib6_nodes can all reference the same fib6_nh. That means validation
of dst_entries based on external nexthops needs to use the IPv4 format
- the per-network namespace counter.
Add sernum to rt6_info and set it when creating a pcpu dst entry. Update
rt6_get_cookie to return sernum if it is set and update dst_check for
IPv6 to look for sernum set and based the check on it if so. Finally,
rt6_get_pcpu_route needs to validate the cached entry before returning
a pcpu entry (similar to the rt_cache_valid calls in __mkroute_input and
__mkroute_output for IPv4).
This problem only affects routes using the new, external nexthops.
Thanks to the kbuild test robot for catching the IS_ENABLED needed
around rt_genid_ipv6 before I sent this out.
Fixes: 5b98324ebe ("ipv6: Allow routes to use nexthop objects")
Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current route nexthop API maintains user space compatibility
with old route API by default. Dumps and netlink notifications
support both new and old API format. In systems which have
moved to the new API, this compatibility mode cancels some
of the performance benefits provided by the new nexthop API.
This patch adds new sysctl nexthop_compat_mode which is on
by default but provides the ability to turn off compatibility
mode allowing systems to run entirely with the new routing
API. Old route API behaviour and support is not modified by this
sysctl.
Uses a single sysctl to cover both ipv4 and ipv6 following
other sysctls. Covers dumps and delete notifications as
suggested by David Ahern.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Used in subsequent work to skip route delete
notifications on nexthop deletes.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having all the sysctl handlers deal with user pointers, which
is rather hairy in terms of the BPF interaction, copy the input to and
from userspace in common code. This also means that the strings are
always NUL-terminated by the common code, making the API a little bit
safer.
As most handler just pass through the data to one of the common handlers
a lot of the changes are mechnical.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The build_state callback of lwtunnel doesn't contain the net namespace
structure yet. This patch will add it so we can check on specific
address configuration at creation time of rpl source routes.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous changes to the IP routing code have removed all the
tests for the DS_HOST route flag.
Remove the flags and all the code that sets it.
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the various uses of fallthrough comments to fallthrough;
Done via script
Link: https://lore.kernel.org/lkml/b56602fcf79f849e733e7b521bb0e17895d390fa.1582230379.git.joe@perches.com/
And by hand:
net/ipv6/ip6_fib.c has a fallthrough comment outside of an #ifdef block
that causes gcc to emit a warning if converted in-place.
So move the new fallthrough; inside the containing #ifdef/#endif too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting an RTA_MULTIPATH request into multiple routes and adding the
second and later components, we must not simply remove NLM_F_REPLACE but
instead replace it by NLM_F_CREATE. Otherwise, it may look like the netlink
message was malformed.
For example,
ip route add 2001:db8::1/128 dev dummy0
ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0 \
nexthop via fe80::30:2 dev dummy0
results in the following warnings:
[ 1035.057019] IPv6: RTM_NEWROUTE with no NLM_F_CREATE or NLM_F_REPLACE
[ 1035.057517] IPv6: NLM_F_CREATE should be set when creating new route
This patch makes the nlmsg sequence look equivalent for __ip6_ins_rt() to
what it would get if the multipath route had been added in multiple netlink
operations:
ip route add 2001:db8::1/128 dev dummy0
ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0
ip route append 2001:db8::1/128 nexthop via fe80::30:2 dev dummy0
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to previous patch, add "offload" and "trap"
indication to IPv6 routes.
This is done by using two unused bits in 'struct fib6_info' to hold
these indications. Capable drivers are expected to set these when
processing the various in-kernel route notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mlxsw is converted to use the new FIB notifications it is
possible to delete the old ones and use the new replace / append /
delete notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an entire multipath route is deleted, only emit a notification if
it is the first route in the node. Emit a replace notification in case
the last sibling is followed by another route. Otherwise, emit a delete
notification.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to previous patches, only notify the new multipath
route if it is the first route in the node or if it was appended to such
route.
The type of the notification (replace vs. append) is determined based on
the number of routes added ('nhn') and the number of sibling routes. If
the two do not match, then an append notification should be sent.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use a per namespace counter, increment it on successful creation
of any route using the source address, decrement it on deletion
of such routes.
This allows us to check easily if the routing decision in the
current namespace depends on the packet source. Will be used
by the next patch.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we will return directly if (!rt || !rt->fib6_nh.fib_nh_gw_family)
in function rt6_probe(), but after commit cc3a86c802
("ipv6: Change rt6_probe to take a fib6_nh"), the logic changed to
return if there is fib_nh_gw_family.
Fixes: cc3a86c802 ("ipv6: Change rt6_probe to take a fib6_nh")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking at a syzbot KCSAN report [1], I found multiple
issues in this code :
1) fib6_nh->last_probe has an initial value of 0.
While probably okay on 64bit kernels, this causes an issue
on 32bit kernels since the time_after(jiffies, 0 + interval)
might be false ~24 days after boot (for HZ=1000)
2) The data-race found by KCSAN
I could use READ_ONCE() and WRITE_ONCE(), but we also can
take the opportunity of not piling-up too many rt6_probe_deferred()
works by using instead cmpxchg() so that only one cpu wins the race.
[1]
BUG: KCSAN: data-race in find_match / find_match
write to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 1:
rt6_probe net/ipv6/route.c:663 [inline]
find_match net/ipv6/route.c:757 [inline]
find_match+0x5bd/0x790 net/ipv6/route.c:733
__find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831
find_rr_leaf net/ipv6/route.c:852 [inline]
rt6_select net/ipv6/route.c:896 [inline]
fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164
ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200
ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452
fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117
ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484
ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497
ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049
ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150
inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106
inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
tcp_transmit_skb net/ipv4/tcp_output.c:1185 [inline]
tcp_xmit_probe_skb+0x19b/0x1d0 net/ipv4/tcp_output.c:3735
read to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 0:
rt6_probe net/ipv6/route.c:657 [inline]
find_match net/ipv6/route.c:757 [inline]
find_match+0x521/0x790 net/ipv6/route.c:733
__find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831
find_rr_leaf net/ipv6/route.c:852 [inline]
rt6_select net/ipv6/route.c:896 [inline]
fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164
ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200
ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452
fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117
ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484
ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497
ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049
ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150
inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106
inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 18894 Comm: udevd Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: cc3a86c802 ("ipv6: Change rt6_probe to take a fib6_nh")
Fixes: f547fac624 ("ipv6: rate-limit probes for neighbourless routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code which recognizes ICMP error packets is duplicated several
times. Use the icmp_is_err() and icmpv6_is_err() helpers instead, which
do the same thing.
ip_multipath_l3_keys() and tcf_nat_act() didn't check for all the error types,
assume that they should instead.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Faster jhash2() can be used instead of jhash(), since
IPv6 addresses have the needed alignment requirement.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the equivalent of commit 2c6b55f45d ("ipv6: fix neighbour
resolution with raw socket") for ip6_confirm_neigh(): we can send a
packet with MSG_CONFIRM on a raw socket for a connected route, so the
gateway would be :: here, and we should pick the next hop using
rt6_nexthop() instead.
This was found by code review and, to the best of my knowledge, doesn't
actually fix a practical issue: the destination address from the packet
is not considered while confirming a neighbour, as ip6_confirm_neigh()
calls choose_neigh_daddr() without passing the packet, so there are no
similar issues as the one fixed by said commit.
A possible source of issues with the existing implementation might come
from the fact that, if we have a cached dst, we won't consider it,
while rt6_nexthop() takes care of that. I might just not be creative
enough to find a practical problem here: the only way to affect this
with cached routes is to have one coming from an ICMPv6 redirect, but
if the next hop is a directly connected host, there should be no
topology for which a redirect applies here, and tests with redirected
routes show no differences for MSG_CONFIRM (and MSG_PROBE) packets on
raw sockets destined to a directly connected host.
However, directly using the dst gateway here is not consistent anymore
with neighbour resolution, and, in general, as we want the next hop,
using rt6_nexthop() looks like the only sane way to fetch it.
Reported-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a stupid bug I recently introduced...
ip6_route_info_create() returns an ERR_PTR(err) and not a NULL on error.
Fixes: d55a2e374a ("net-ipv6: fix excessive RTF_ADDRCONF flag on ::1/128 local route (and others)'")
Cc: David Ahern <dsahern@gmail.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a v4 route that uses a v6 nexthop from a nexthop group.
Allow the kernel to properly send the nexthop as v6 via the RTA_VIA
attribute.
Broken behavior:
$ ip nexthop add via fe80::9 dev eth0
$ ip nexthop show
id 1 via fe80::9 dev eth0 scope link
$ ip route add 4.5.6.7/32 nhid 1
$ ip route show
default via 10.0.2.2 dev eth0
4.5.6.7 nhid 1 via 254.128.0.0 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
$
Fixed behavior:
$ ip nexthop add via fe80::9 dev eth0
$ ip nexthop show
id 1 via fe80::9 dev eth0 scope link
$ ip route add 4.5.6.7/32 nhid 1
$ ip route show
default via 10.0.2.2 dev eth0
4.5.6.7 nhid 1 via inet6 fe80::9 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
$
v2, v3: Addresses code review comments from David Ahern
Fixes: dcb1ecb50e (“ipv4: Prepare for fib6_nh from a nexthop object”)
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A change to the core nla helpers was missed during the push of
the nexthop changes. rt6_fill_node_nexthop should be calling
nla_nest_start_noflag not nla_nest_start. Currently, iproute2
does not print multipath data because of parsing issues with
the attribute.
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a subtle change in behaviour introduced by:
commit c7a1ce397a
'ipv6: Change addrconf_f6i_alloc to use ip6_route_info_create'
Before that patch /proc/net/ipv6_route includes:
00000000000000000000000000000001 80 00000000000000000000000000000000 00 00000000000000000000000000000000 00000000 00000003 00000000 80200001 lo
Afterwards /proc/net/ipv6_route includes:
00000000000000000000000000000001 80 00000000000000000000000000000000 00 00000000000000000000000000000000 00000000 00000002 00000000 80240001 lo
ie. the above commit causes the ::1/128 local (automatic) route to be flagged with RTF_ADDRCONF (0x040000).
AFAICT, this is incorrect since these routes are *not* coming from RA's.
As such, this patch restores the old behaviour.
Fixes: c7a1ce397a ("ipv6: Change addrconf_f6i_alloc to use ip6_route_info_create")
Cc: David Ahern <dsahern@gmail.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the unlock path in __ip6_rt_update_pmtu by using a
single point where rcu_read_unlock is called.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nexthop path in rt6_update_exception_stamp_rt needs to call
rcu_read_unlock if it fails to find a fib6_nh match rather than
just returning.
Fixes: e659ba31d8 ("ipv6: Handle all fib6_nh in a nexthop in exception handling")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix AF_XDP cq entry leak, from Ilya Maximets.
2) Fix handling of PHY power-down on RTL8411B, from Heiner Kallweit.
3) Add some new PCI IDs to iwlwifi, from Ihab Zhaika.
4) Fix handling of neigh timers wrt. entries added by userspace, from
Lorenzo Bianconi.
5) Various cases of missing of_node_put(), from Nishka Dasgupta.
6) The new NET_ACT_CT needs to depend upon NF_NAT, from Yue Haibing.
7) Various RDS layer fixes, from Gerd Rausch.
8) Fix some more fallout from TCQ_F_CAN_BYPASS generalization, from
Cong Wang.
9) Fix FIB source validation checks over loopback, also from Cong Wang.
10) Use promisc for unsupported number of filters, from Justin Chen.
11) Missing sibling route unlink on failure in ipv6, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
tcp: fix tcp_set_congestion_control() use from bpf hook
ag71xx: fix return value check in ag71xx_probe()
ag71xx: fix error return code in ag71xx_probe()
usb: qmi_wwan: add D-Link DWM-222 A2 device ID
bnxt_en: Fix VNIC accounting when enabling aRFS on 57500 chips.
net: dsa: sja1105: Fix missing unlock on error in sk_buff()
gve: replace kfree with kvfree
selftests/bpf: fix test_xdp_noinline on s390
selftests/bpf: fix "valid read map access into a read-only array 1" on s390
net/mlx5: Replace kfree with kvfree
MAINTAINERS: update netsec driver
ipv6: Unlink sibling route in case of failure
liquidio: Replace vmalloc + memset with vzalloc
udp: Fix typo in net/ipv4/udp.c
net: bcmgenet: use promisc for unsupported filters
ipv6: rt6_check should return NULL if 'from' is NULL
tipc: initialize 'validated' field of received packets
selftests: add a test case for rp_filter
fib: relax source validation check for loopback packets
mlxsw: spectrum: Do not process learned records with a dummy FID
...
In the sysctl code the proc_dointvec_minmax() function is often used to
validate the user supplied value between an allowed range. This
function uses the extra1 and extra2 members from struct ctl_table as
minimum and maximum allowed value.
On sysctl handler declaration, in every source file there are some
readonly variables containing just an integer which address is assigned
to the extra1 and extra2 members, so the sysctl range is enforced.
The special values 0, 1 and INT_MAX are very often used as range
boundary, leading duplication of variables like zero=0, one=1,
int_max=INT_MAX in different source files:
$ git grep -E '\.extra[12].*&(zero|one|int_max)' |wc -l
248
Add a const int array containing the most commonly used values, some
macros to refer more easily to the correct array member, and use them
instead of creating a local one for every object file.
This is the bloat-o-meter output comparing the old and new binary
compiled with the default Fedora config:
# scripts/bloat-o-meter -d vmlinux.o.old vmlinux.o
add/remove: 2/2 grow/shrink: 0/2 up/down: 24/-188 (-164)
Data old new delta
sysctl_vals - 12 +12
__kstrtab_sysctl_vals - 12 +12
max 14 10 -4
int_max 16 - -16
one 68 - -68
zero 128 28 -100
Total: Before=20583249, After=20583085, chg -0.00%
[mcroce@redhat.com: tipc: remove two unused variables]
Link: http://lkml.kernel.org/r/20190530091952.4108-1-mcroce@redhat.com
[akpm@linux-foundation.org: fix net/ipv6/sysctl_net_ipv6.c]
[arnd@arndb.de: proc/sysctl: make firmware loader table conditional]
Link: http://lkml.kernel.org/r/20190617130014.1713870-1-arnd@arndb.de
[akpm@linux-foundation.org: fix fs/eventpoll.c]
Link: http://lkml.kernel.org/r/20190430180111.10688-1-mcroce@redhat.com
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul reported that l2tp sessions were broken after the commit referenced
in the Fixes tag. Prior to this commit rt6_check returned NULL if the
rt6_info 'from' was NULL - ie., the dst_entry was disconnected from a FIB
entry. Restore that behavior.
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: Paul Donohue <linux-kernel@PaulSD.com>
Tested-by: Paul Donohue <linux-kernel@PaulSD.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the same support as commit 363887a2cd ("ipv4: Support multipath
hashing on inner IP pkts for GRE tunnel") for outer IPv6. The hashing
considers both IPv4 and IPv6 pkts when they are tunneled by IPv6 GRE.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use blackhole_netdev instead of 'lo' device with lower MTU when marking
dst "dead".
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Tested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Gateway validation does not need a dst_entry, it only needs the fib
entry to validate the gateway resolution and egress device. So,
convert ip6_nh_lookup_table from ip6_pol_route to fib6_table_lookup
and ip6_route_check_nh to use fib6_lookup over rt6_lookup.
ip6_pol_route is a call to fib6_table_lookup and if successful a call
to fib6_select_path. From there the exception cache is searched for an
entry or a dst_entry is created to return to the caller. The exception
entry is not relevant for gateway validation, so what matters are the
calls to fib6_table_lookup and then fib6_select_path.
Similarly, rt6_lookup can be replaced with a call to fib6_lookup with
RT6_LOOKUP_F_IFACE set in flags. Again, the exception cache search is
not relevant, only the lookup with path selection. The primary difference
in the lookup paths is the use of rt6_select with fib6_lookup versus
rt6_device_match with rt6_lookup. When you remove complexities in the
rt6_select path, e.g.,
1. saddr is not set for gateway validation, so RT6_LOOKUP_F_HAS_SADDR
is not relevant
2. rt6_check_neigh is not called so that removes the RT6_NUD_FAIL_DO_RR
return and round-robin logic.
the code paths are believed to be equivalent for the given use case -
validate the gateway and optionally given the device. Furthermore, it
aligns the validation with onlink code path and the lookup path actually
used for rx and tx.
Adjust the users, ip6_route_check_nh_onlink and ip6_route_check_nh to
handle a fib6_info vs a rt6_info when performing validation checks.
Existing selftests fib-onlink-tests.sh and fib_tests.sh are used to
verify the changes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scenario is the following: the user uses a raw socket to send an ipv6
packet, destinated to a not-connected network, and specify a connected nh.
Here is the corresponding python script to reproduce this scenario:
import socket
IPPROTO_RAW = 255
send_s = socket.socket(socket.AF_INET6, socket.SOCK_RAW, IPPROTO_RAW)
# scapy
# p = IPv6(src='fd00💯:1', dst='fd00:200::fa')/ICMPv6EchoRequest()
# str(p)
req = b'`\x00\x00\x00\x00\x08:@\xfd\x00\x01\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x01\xfd\x00\x02\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\xfa\x80\x00\x81\xc0\x00\x00\x00\x00'
send_s.sendto(req, ('fd00:175::2', 0, 0, 0))
fd00:175::/64 is a connected route and fd00:200::fa is not a connected
host.
With this scenario, the kernel starts by sending a NS to resolve
fd00:175::2. When it receives the NA, it flushes its queue and try to send
the initial packet. But instead of sending it, it sends another NS to
resolve fd00:200::fa, which obvioulsy fails, thus the packet is dropped. If
the user sends again the packet, it now uses the right nh (fd00:175::2).
The problem is that ip6_dst_lookup_neigh() uses the rt6i_gateway, which is
:: because the associated route is a connected route, thus it uses the dst
addr of the packet. Let's use rt6_nexthop() to choose the right nh.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/sys/net/ipv6/route/skip_notify_on_dev_down assumes given value to be
0 or 1. Use proc_dointvec_minmax instead of proc_dointvec.
Fixes: 7c6bb7d2fa ("net/ipv6: Add knob to skip DELROUTE message ondevice down")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2b760fcf5c ("ipv6: hook up exception table to store dst
cache"), route exceptions reside in a separate hash table, and won't be
found by walking the FIB, so they won't be dumped to userspace on a
RTM_GETROUTE message.
This causes 'ip -6 route list cache' and 'ip -6 route flush cache' to
have no function anymore:
# ip -6 route get fc00:3::1
fc00:3::1 via fc00:1::2 dev veth_A-R1 src fc00:1::1 metric 1024 expires 539sec mtu 1400 pref medium
# ip -6 route get fc00:4::1
fc00:4::1 via fc00:2::2 dev veth_A-R2 src fc00:2::1 metric 1024 expires 536sec mtu 1500 pref medium
# ip -6 route list cache
# ip -6 route flush cache
# ip -6 route get fc00:3::1
fc00:3::1 via fc00:1::2 dev veth_A-R1 src fc00:1::1 metric 1024 expires 520sec mtu 1400 pref medium
# ip -6 route get fc00:4::1
fc00:4::1 via fc00:2::2 dev veth_A-R2 src fc00:2::1 metric 1024 expires 519sec mtu 1500 pref medium
because iproute2 lists cached routes using RTM_GETROUTE, and flushes them
by listing all the routes, and deleting them with RTM_DELROUTE one by one.
If cached routes are requested using the RTM_F_CLONED flag together with
strict checking, or if no strict checking is requested (and hence we can't
consistently apply filters), look up exceptions in the hash table
associated with the current fib6_info in rt6_dump_route(), and, if present
and not expired, add them to the dump.
We might be unable to dump all the entries for a given node in a single
message, so keep track of how many entries were handled for the current
node in fib6_walker, and skip that amount in case we start from the same
partially dumped node.
When a partial dump restarts, as the starting node might change when
'sernum' changes, we have no guarantee that we need to skip the same
amount of in-node entries. Therefore, we need two counters, and we need to
zero the in-node counter if the node from which the dump is resumed
differs.
Note that, with the current version of iproute2, this only fixes the
'ip -6 route list cache': on a flush command, iproute2 doesn't pass
RTM_F_CLONED and, due to this inconsistency, 'ip -6 route flush cache' is
still unable to fetch the routes to be flushed. This will be addressed in
a patch for iproute2.
To flush cached routes, a procfs entry could be introduced instead: that's
how it works for IPv4. We already have a rt6_flush_exception() function
ready to be wired to it. However, this would not solve the issue for
listing.
Versions of iproute2 and kernel tested:
iproute2
kernel 4.14.0 4.15.0 4.19.0 5.0.0 5.1.0 5.1.0, patched
3.18 list + + + + + +
flush + + + + + +
4.4 list + + + + + +
flush + + + + + +
4.9 list + + + + + +
flush + + + + + +
4.14 list + + + + + +
flush + + + + + +
4.15 list
flush
4.19 list
flush
5.0 list
flush
5.1 list
flush
with list + + + + + +
fix flush + + + +
v7:
- Explain usage of "skip" counters in commit message (suggested by
David Ahern)
v6:
- Rebase onto net-next, use recently introduced nexthop walker
- Make rt6_nh_dump_exceptions() a separate function (suggested by David
Ahern)
v5:
- Use dump_routes and dump_exceptions from filter, ignore NLM_F_MATCH,
update test results (flushing works with iproute2 < 5.0.0 now)
v4:
- Split NLM_F_MATCH and strict check handling in separate patches
- Filter routes using RTM_F_CLONED: if it's not set, only return
non-cached routes, and if it's set, only return cached routes:
change requested by David Ahern and Martin Lau. This implies that
iproute2 needs a separate patch to be able to flush IPv6 cached
routes. This is not ideal because we can't fix the breakage caused
by 2b760fcf5c entirely in kernel. However, two years have passed
since then, and this makes it more tolerable
v3:
- More descriptive comment about expired exceptions in rt6_dump_route()
- Swap return values of rt6_dump_route() (suggested by Martin Lau)
- Don't zero skip_in_node in case we don't dump anything in a given pass
(also suggested by Martin Lau)
- Remove check on RTM_F_CLONED altogether: in the current UAPI semantic,
it's just a flag to indicate the route was cloned, not to filter on
routes
v2: Add tracking of number of entries to be skipped in current node after
a partial dump. As we restart from the same node, if not all the
exceptions for a given node fit in a single message, the dump will
not terminate, as suggested by Martin Lau. This is a concrete
possibility, setting up a big number of exceptions for the same route
actually causes the issue, suggested by David Ahern.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 2b760fcf5c ("ipv6: hook up exception table to store dst cache")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the next patch, we are going to add optional dump of exceptions to
rt6_dump_route().
Change the return code of rt6_dump_route() to accomodate partial node
dumps: we might dump multiple routes per node, and might be able to dump
only a given number of them, so fib6_dump_node() will need to know how
many routes have been dumped on partial dump, to restart the dump from the
point where it was interrupted.
Note that fib6_dump_node() is the only caller and already handles all
non-negative return codes as success: those become -1 to signal that we're
done with the node. If we fail, return 0, as we were unable to dump the
single route in the node, but we're not done with it.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If fc_nh_id isn't set, we shouldn't try to match against it. This
actually matters just for the RTF_CACHE below (where this case is
already handled): if iproute2 gets a route exception and tries to
delete it, it won't reference it by fc_nh_id, even if a nexthop
object might be associated to the originating route.
Fixes: 5b98324ebe ("ipv6: Allow routes to use nexthop objects")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For tx path, in most cases, we still have to take refcnt on the dst
cause the caller is caching the dst somewhere. But it still is
beneficial to make use of RT6_LOOKUP_F_DST_NOREF flag while doing the
route lookup. It is cause this flag prevents manipulating refcnt on
net->ipv6.ip6_null_entry when doing fib6_rule_lookup() to traverse each
routing table. The null_entry is a shared object and constant updates on
it cause false sharing.
We converted the current major lookup function ip6_route_output_flags()
to make use of RT6_LOOKUP_F_DST_NOREF.
Together with the change in the rx path, we see noticable performance
boost:
I ran synflood tests between 2 hosts under the same switch. Both hosts
have 20G mlx NIC, and 8 tx/rx queues.
Sender sends pure SYN flood with random src IPs and ports using trafgen.
Receiver has a simple TCP listener on the target port.
Both hosts have multiple custom rules:
- For incoming packets, only local table is traversed.
- For outgoing packets, 3 tables are traversed to find the route.
The packet processing rate on the receiver is as follows:
- Before the fix: 3.78Mpps
- After the fix: 5.50Mpps
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_input() is the key function to do the route lookup in the
rx data path. All the callers to this function are already holding rcu
lock. So it is fairly easy to convert it to not take refcnt on the dst:
We pass in flag RT6_LOOKUP_F_DST_NOREF and do skb_dst_set_noref().
This saves a few atomic inc or dec operations and should boost
performance overall.
This also makes the logic more aligned with v4.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize rt6->rt6i_uncached on the following pre-allocated dsts:
net->ipv6.ip6_null_entry
net->ipv6.ip6_prohibit_entry
net->ipv6.ip6_blk_hole_entry
This is a preparation patch for later commits to be able to distinguish
dst entries in uncached list by doing:
!list_empty(rt6->rt6i_uncached)
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new flag is to instruct the route lookup function to not take
refcnt on the dst entry. The user which does route lookup with this flag
must properly use rcu protection.
ip6_pol_route() is the major route lookup function for both tx and rx
path.
In this function:
Do not take refcnt on dst if RT6_LOOKUP_F_DST_NOREF flag is set, and
directly return the route entry. The caller should be holding rcu lock
when using this flag, and decide whether to take refcnt or not.
One note on the dst cache in the uncached_list:
As uncached_list does not consume refcnt, one refcnt is always returned
back to the caller even if RT6_LOOKUP_F_DST_NOREF flag is set.
Uncached dst is only possible in the output path. So in such call path,
caller MUST check if the dst is in the uncached_list before assuming
that there is no refcnt taken on the returned dst.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user reported that routes are getting installed with type 0 (RTN_UNSPEC)
where before the routes were RTN_UNICAST. One example is from accel-ppp
which apparently still uses the ioctl interface and does not set
rtmsg_type. Another is the netlink interface where ipv6 does not require
rtm_type to be set (v4 does). Prior to the commit in the Fixes tag the
ipv6 stack converted type 0 to RTN_UNICAST, so restore that behavior.
Fixes: e8478e80e5 ("net/ipv6: Save route type in rt6_info")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If all the nexthops of a multipath route are being deleted, send one
notification for the entire route, instead of one per-nexthop.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emit a notification when a multipath routes is added or replace.
Note that unlike the replace notifications sent from fib6_add_rt2node(),
it is possible we are sending a 'FIB_EVENT_ENTRY_REPLACE' when a route
was merely added and not replaced.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RTA_NH_ID attribute to allow a user to specify a
nexthop id to use with a route. fc_nh_id is added to fib6_config to
hold the value passed in the RTA_NH_ID attribute. If a nexthop id
is given, the gateway, device, encap and multipath attributes can
not be set.
Update ip6_route_del to check metric and protocol before nexthop
specs. If fc_nh_id is set, then it must match the id in the route
entry. Since IPv6 allows delete of a cached entry (an exception),
add ip6_del_cached_rt_nh to cycle through all of the fib6_nh in
a fib entry if it is using a nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use nexthop_for_each_fib6_nh to call fib6_nh_mtu_change for each
fib6_nh in a nexthop for rt6_mtu_change_route. For __ip6_rt_update_pmtu,
we need to find the nexthop that correlates to the device and gateway
in the rt6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use nexthop_for_each_fib6_nh and fib6_nh_find_match to find the
fib6_nh in a nexthop that correlates to the device and gateway
in the rt6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a hook in __ip6_route_redirect to handle a nexthop struct in a
fib6_info. Use nexthop_for_each_fib6_nh and fib6_nh_redirect_match
to call ip6_redirect_nh_match for each fib6_nh looking for a match.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a hook in rt6_flush_exceptions, rt6_remove_exception_rt,
rt6_update_exception_stamp_rt, and rt6_age_exceptions to handle
nexthop struct in a fib6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a hook in fib6_info_uses_dev to handle nexthop struct in a fib6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a hook in rt6_nlmsg_size to handle nexthop struct in a fib6_info.
rt6_nh_nlmsg_size is used to sum the space needed for all nexthops in
the fib entry.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
