Back in commit 826cff3f7e ("drm/bridge: parade-ps8640: Enable
runtime power management") we removed a mysterious 50 ms delay because
"Parade's support [couldn't] explain what the delay [was] for".
While I'm always a fan of removing mysterious delays, I suspect that
we need this mysterious delay to avoid some problems.
Specifically, what I found recently is that on sc7180-trogdor-homestar
sometimes the AUX backlight wasn't initializing properly. Some
debugging showed that the drm_dp_dpcd_read() function that the AUX
backlight driver was calling was returning bogus data about 1% of the
time when I booted up. This confused
drm_panel_dp_aux_backlight(). From continued debugging:
- If I retried the read then the read worked just fine.
- If I added a loop to perform the same read that
drm_panel_dp_aux_backlight() was doing 30 times at bootup I could
see that some percentage of the time the first read would give bogus
data but all 29 additional reads would always be fine.
- If I added a large delay _after_ powering on the panel but before
powering on PS8640 I could still reproduce the problem.
- If I added a delay after PS8640 powered on then I couldn't reproduce
the problem.
- I couldn't reproduce the problem on a board with the same panel but
the ti-sn65dsi86 bridge chip.
To me, the above indicated that there was a problem with PS8640 and
not the panel.
I don't really have any insight into what's going on in the MCU, but
my best guess is that when the MCU itself sees the HPD go high that it
does some AUX transfers itself and this is confusing things.
Let's go back and add back in the mysterious 50 ms delay. We only want
to do this the first time we see HPD go high after booting the MCU,
not every time we double-check HPD.
With this, the backlight initializes reliably on homestar.
Fixes: 826cff3f7e ("drm/bridge: parade-ps8640: Enable runtime power management")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221017121813.1.I59700c745fbc31559a5d5c8e2a960279c751dbd5@changeid
The double reset power-on sequence is a workaround for the hardware
flaw in some chip that SPI Clock output glitch and cause internal MPU
unable to read firmware correctly. The sequence is suggested in ps8640
application note.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Rock Chiu <rock.chiu@paradetech.corp-partner.google.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220815093905.134164-1-hsinyi@chromium.org
The datasheet says that VDD12 must be enabled and at full voltage before
VDD33 is enabled.
Reorder the bulk regulator supply names so that VDD12 is enabled before
VDD33. Any enable ramp delays should be handled by setting proper
constraints on the regulators.
Fixes: bc1aee7fc8 ("drm/bridge: Add I2C based driver for ps8640 bridge")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220721092258.3397461-1-wenst@chromium.org
This implements the callback added by the patch ("drm/dp: Add
wait_hpd_asserted() callback to struct drm_dp_aux").
With this change and all the two "DP AUX Endpoint" drivers changed to
use wait_hpd_asserted(), we no longer need to have an long delay in
the AUX transfer function. It's up to the panel code to make sure that
the panel is powered now. If someone tried to call the aux transfer
function without making sure the panel is powered we'll just get a
normal transfer failure.
We'll still keep the wait for HPD in the pre_enable() function. Though
it's probably not actually needed there, this driver is used in the
old mode (pre-DP AUX Endpoints) and it may be important for those
cases. If nothing else, it shouldn't cause any big problems.
NOTE: When handling the timeout for HPD we start the timer _after_
we've runtime resumed the device. This is definitely important for the
panel on my homestar which comes up 170 ms after we start timing (the
panel specifies 200 ms max). It's a little unclear how much of this
extra time is due to some internal state machine in the parade
firmware vs. debouncing but it seems to work for the two test cases I
have to do it this way.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220614145327.v4.4.Ie827321ce263be52fdb8c1276f6f8cc00d78029f@changeid
drm_crtc.h has no need for drm_edid.h, so don't include it.
Avoids useless rebuilds of the entire universe when
touching drm_edid.h.
Quite a few placs do currently depend on drm_edid.h without
actually including it directly. All of those need to be fixed
up.
v2: Fix up i915 and msm some more
v3: Fix alphabetical ordering (Sam)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220614090245.30283-1-ville.syrjala@linux.intel.com
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
While it works, for the most part, to assume that the panel has
finished probing when devm_of_dp_aux_populate_ep_devices() returns,
it's a bit fragile. This is talked about at length in commit
a1e3667a98 ("drm/bridge: ti-sn65dsi86: Promote the AUX channel to
its own sub-dev").
When reviewing the ps8640 code, I managed to convince myself that it
was OK not to worry about it there and that maybe it wasn't really
_that_ fragile. However, it turns out that it really is. Simply
hardcoding panel_edp_probe() to return -EPROBE_DEFER was enough to put
the boot process into an infinite loop. I believe this manages to trip
the same issues that we used to trip with the main MSM code where
something about our actions trigger Linux to re-probe previously
deferred devices right away and each time we try again we re-trigger
Linux to re-probe.
Let's fix this using the callback introduced in the patch ("drm/dp:
Callbacks to make it easier for drivers to use DP AUX bus properly").
When using the new callback, we have to be a little careful. The
probe_done() callback is no longer always called in the context of
our probe routine. That means we can't rely on being able to return
-EPROBE_DEFER from it. We re-jigger the order of things a bit to
account for that.
With this change, the device still boots (though obviously the panel
doesn't come up) if I force panel-edp to always return
-EPROBE_DEFER. If I fake it and make the panel probe exactly once it
also works.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510122726.v3.4.Ia6324ebc848cd40b4dbd3ad3289a7ffb5c197779@changeid
Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.
Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.
v2:
* update commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-3-tzimmermann@suse.de
Entering suspend while the display attached to this bridge is still on
makes the resume sequence to resume the bridge first, display last:
when this happens, we get a timeout while resuming the bridge, as its
MCU will get stuck due to the display being unpowered.
On the other hand, on mt8173-elm, closing the lid makes the display to
get powered off first, bridge last, so at resume time the sequence is
swapped (compared to the first example) and everything just works
as expected.
Add a stateless device link to the DRM device that this bridge belongs
to, ensuring a correct resume sequence and solving the unability to
correctly resume bridge operation in the first mentioned example.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220105090802.73564-1-angelogioacchino.delregno@collabora.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
When we added the support for the AUX channel in commit 13afcdd727
("drm/bridge: parade-ps8640: Add support for AUX channel") we forgot
to set "drm_dev" to avoid the warning splat at the beginning of
drm_dp_aux_register(). Since everything was working I guess I never
noticed the splat when testing against mainline. In any case, it's
easy to fix. This is basically just like commit 6cba3fe433 ("drm/dp:
Add backpointer to drm_device in drm_dp_aux") but just for the
parade-ps8640.
Fixes: 13afcdd727 ("drm/bridge: parade-ps8640: Add support for AUX channel")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211206162907.1.I1f5d1eba741e4663050ec1b8e39a753f6e42e38b@changeid
Through log and waveform, we can see that there will be additional
suspend/resume when booting. This timing does not meet the ps8640 spec.
It seems that the delay of 500ms does not satisfied drm_panel_get_modes.
I increased it to 900ms and it seems that this problem can be solved.
To be safe, I'd just round up to a full 1000.
Signed-off-by: yangcong <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211112084302.2447931-1-yangcong5@huaqin.corp-partner.google.com
Conventionally, panel is listed under the root of the device tree.
When userland asks for display mode, ps8640 bridge is responsible
for returning EDID when ps8640_bridge_get_edid() is called.
Now enable a new option of listing panel under "aux-bus" of ps8640
bridge node in the device tree. In this case, panel driver can retrieve
EDID by triggering AUX transactions, without ps8640_bridge_get_edid()
calls at all.
To prevent the "old" and "new" options from interfering with each
other's logic flow, disable DRM_BRIDGE_OP_EDID when the new option
is taken.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211028105754.v5.2.I09899dea340f11feab97d719cb4b62bef3179e4b@changeid
Fit ps8640 driver into runtime power management framework:
First, break _poweron() to 3 parts: (1) turn on power and wait for
ps8640's internal MCU to finish init (2) check panel HPD (which is
proxied by GPIO9) (3) the other configs. As runtime_resume() can be
called before panel is powered, we only add (1) to _resume() and leave
(2)(3) to _pre_enable(). We also add (2) to _aux_transfer() as we want
to ensure panel HPD is asserted before we start AUX CH transactions.
Second, the original driver has a mysterious delay of 50 ms between (2)
and (3). Since Parade's support can't explain what the delay is for,
and we don't see removing the delay break any boards at hand, remove
the delay to fit into this driver change.
In addition, rename "powered" to "pre_enabled" and don't check for it
in the pm_runtime calls. The pm_runtime calls are already refcounted
so there's no reason to check there. The other user of "powered",
_get_edid(), only cares if pre_enable() has already been called.
Lastly, change some existing DRM_...() logging to dev_...() along the
way, since DRM_...() seem to be deprecated in [1].
[1] https://patchwork.freedesktop.org/patch/454760/
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
[dianders: fixed whitespace warning reported by dim tool]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211028105754.v5.1.I828f5db745535fb7e36e8ffdd62d546f6d08b6d1@changeid
In order to avoid any probe ordering issue, the best practice is to move
the secondary MIPI-DSI device registration and attachment to the
MIPI-DSI host at probe time. Let's do this.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025151536.1048186-13-maxime@cerno.tech
Implement the first version of AUX support, which will be useful as
we expand the driver to support varied use cases.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
[dianders: whitespace fixes reported by dim apply-branch]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921110556.v6.2.I1d6ea362dc76efa77cca2b46253d31b7651eaf17@changeid
Replace the direct i2c access (i2c_smbus_* functions) with regmap APIs,
which will simplify the future update on ps8640 driver.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
[dianders: whitespace fixes reported by dim apply-branch]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921110556.v6.1.I2351df94f18d5d8debc22d4d100f36fac560409a@changeid
Reorg the macros as follows:
(1) Group the registers on the same page together.
(2) Group the register and its bit operation together while indenting
the macros of the bit operation with one space.
Also fix a misnomer for the number of mipi data lanes.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210824181140.v2.1.I8ead7431357409f2526e5739ec5bc3ddfd242243@changeid
The get_edid() callback can be triggered anytime by an ioctl, i.e
drm_mode_getconnector (ioctl)
-> drm_helper_probe_single_connector_modes
-> drm_bridge_connector_get_modes
-> ps8640_bridge_get_edid
Actually if the bridge pre_enable() function was not called before
get_edid(), the driver will not be able to get the EDID properly and
display will not work until a second get_edid() call is issued and if
pre_enable() is called before. The side effect of this, for example, is
that you see anything when `Frecon` starts, neither the splash screen,
until the graphical session manager starts.
To fix this we need to make sure that all we need is enabled before
reading the EDID. This means the following:
1. If get_edid() is called before having the device powered we need to
power on the device. In such case, the driver will power off again the
device.
2. If get_edid() is called after having the device powered, all should
just work. We added a powered flag in order to avoid recurrent calls
to ps8640_bridge_poweron() and unneeded delays.
3. This seems to be specific for this device, but we need to make sure
the panel is powered on before do a power on cycle on this device.
Otherwise the device fails to retrieve the EDID.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Bilal Wasim <bwasim.lkml@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200827085911.944899-2-enric.balletbo@collabora.com
Print an error message inside ps8640_bridge_vdo_control() function when
it fails so we can simplify a bit the callers, they will only need to
check the error code.
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Bilal Wasim <bwasim.lkml@gmail.com>
Tested-by: Bilal Wasim <bwasim.lkml@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826081526.674866-5-enric.balletbo@collabora.com
Bridge drivers that implement the new model only shall return an error
from their attach() handler when the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag
is not set. So make sure we return an error because only the new
drm_bridge model is supported.
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Bilal Wasim <bwasim.lkml@gmail.com>
Tested-by: Bilal Wasim <bwasim.lkml@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826081526.674866-4-enric.balletbo@collabora.com
The PS8640 DSI-to-eDP bridge can retrieve the EDID, so implement the
.get_edid callback and set the flag to indicate the core to use it.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826081526.674866-3-enric.balletbo@collabora.com
The panel connector type should be set by the panel not the bridge, so
remove the connector_type assignment.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200416164404.2418426-2-enric.balletbo@collabora.com
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
