Add pmbus driver support for Maxim MAX15301 InTune Automatically
Compensated Digital PoL Controller with Driver and PMBus Telemetry
Even though the specification does not specifically mention it,
extensive empirical testing has revealed that auto-detection of
limit-registers will fail in a random fashion unless the delay
parameter is set to above about 80us. The default delay is set
to 100us to include some safety margin.
This patch is tested on a Flex BMR461 converter module.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210419101251.24840-1-erik.rosen@metormote.com
[groeck: Added rationale for delay to driver header]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for these devices:
- YH-5151E - the PDU
- YM-2151E - the PSU
The device datasheet says that the devices support PMBus 1.2, but in my
testing, a lot of the commands aren't supported and if they are, they
sometimes behave strangely or inconsistently. For example, writes to the
PAGE command requires using PEC, otherwise the write won't work and the
page won't switch, even though, the standard says that PEC is optional.
On the other hand, writes to SMBALERT don't require PEC. Because of
this, the driver is mostly reverse engineered with the help of a tool
called pmbus_peek written by David Brownell (and later adopted by my
colleague Jan Kundrát).
The device also has some sort of a timing issue when switching pages,
which is explained further in the code.
Because of this, the driver support is limited. It exposes only the
values that have been tested to work correctly.
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210414080019.3530794-1-kubernat@cesnet.cz
[groeck: Fixed up "missing braces around initializer" from 0-day]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for TI TPS53676 controller to the tps53679 pmbus driver
The driver uses the USER_DATA_03 register to figure out how many phases
are enabled and to which channel they are assigned, and sets the number
of pages and phases accordingly.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210322193734.75127-3-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The BPA-RS600 is a compact 600W AC to DC removable power supply module.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210317040231.21490-3-chris.packham@alliedtelesis.co.nz
[groeck: Added bpa-rs600 to index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These are "all-in-one" CPU liquid coolers that can be monitored and
controlled through a proprietary USB HID protocol.
While the models have differently sized radiators and come with varying
numbers of fans, they are all indistinguishable at the software level.
The driver exposes fan/pump speeds and coolant temperature through the
standard hwmon sysfs interface.
Fan and pump control, while supported by the devices, are not currently
exposed. The firmware accepts up to 61 trip points per channel
(fan/pump), but the same set of trip temperatures has to be maintained
for both; with pwmX_auto_point_Y_temp attributes, users would need to
maintain this invariant themselves.
Instead, fan and pump control, as well as LED control (which the device
also supports for 9 addressable RGB LEDs on the CPU water block) are
left for existing and already mature user-space tools, which can still
be used alongside the driver, thanks to hidraw. A link to one, which I
also maintain, is provided in the documentation.
The implementation is based on USB traffic analysis. It has been
runtime tested on x86_64, both as a built-in driver and as a module.
Signed-off-by: Jonas Malaco <jonas@protocubo.io>
Link: https://lore.kernel.org/r/20210319045544.416138-1-jonas@protocubo.io
[groeck: Removed unnecessary spinlock.h include]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adds support for reading the critical values of the temperature sensors
and the rail sensors (voltage and current) once and caches them. Updates
the naming of the constants following a more clear scheme. Also updates
the documentation and fixes some typos. Updates is_visible and ops_read
functions to be more readable.
The new sensors output of a Corsair HX850i will look like this:
corsairpsu-hid-3-1
Adapter: HID adapter
v_in: 230.00 V
v_out +12v: 12.14 V (crit min = +8.41 V, crit max = +15.59 V)
v_out +5v: 5.03 V (crit min = +3.50 V, crit max = +6.50 V)
v_out +3.3v: 3.30 V (crit min = +2.31 V, crit max = +4.30 V)
psu fan: 0 RPM
vrm temp: +46.2°C (crit = +70.0°C)
case temp: +39.8°C (crit = +70.0°C)
power total: 152.00 W
power +12v: 108.00 W
power +5v: 41.00 W
power +3.3v: 5.00 W
curr +12v: 9.00 A (crit max = +85.00 A)
curr +5v: 8.31 A (crit max = +40.00 A)
curr +3.3v: 1.62 A (crit max = +40.00 A)
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/YFNg6vGk3sQmyqgB@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add hardware monitoring support for ST STPDDC60 Unversal Digital
Multicell Controller.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210218115249.28513-3-erik.rosen@metormote.com
[groeck: Fixed whitespace error in Makefile]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add basic monitoring support as well as port on/off control for Texas
Instruments TPS23861 PoE PSE IC.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210121134434.2782405-2-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX16508 is quite similar to MAX16601, except that it does not support
the DEFAULT_NUM_POP register and we thus can not dynamically determine
the number of populated phases.
Cc: Alex Qiu <xqiu@google.com>
Cc: Ugur Usug <Ugur.Usug@maximintegrated.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210125185327.93282-2-linux@roeck-us.net
Reviewed-by: Alex Qiu <xqiu@google.com>
Tested-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX16601 can report the number of populated phases. Use this
information to only create sysfs attributes for populated phases.
Cc: Alex Qiu <xqiu@google.com>
Cc: Ugur Usug <Ugur.Usug@maximintegrated.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210125185327.93282-1-linux@roeck-us.net
Reviewed-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds a hwmon driver for the AHT10 Temperature and
Humidity sensor. It has a maximum sample rate, as the datasheet
states that the chip may heat up if it is sampled more than once
every two seconds.
Has been tested a to work on a raspberrypi0w
Signed-off-by: Johannes Cornelis Draaijer (datdenkikniet) <jcdra1@gmail.com>
Link: https://lore.kernel.org/r/20210107194014.GA88780@desktop
[groeck: dropped AHT10_ADDR (unused) and use AHT10_MEAS_SIZE where
appropriate; dropped change log]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This deletes the ABx500 hwmon driver, the only supported
variant being the AB8500.
This driver has been replaced by generic frameworks. By
inspecting the abx500 sysfs files we see that it contains
things such as temp1_max, temp1_max_alarm, temp1_max_hyst,
temp1_max_hyst_alarm, temp1_min, temp1_min_alarm.
It becomes obvious that the abx500.c is a reimplementation
of thermal zones. This is not very strange as the generic
thermal zones were not invented when this driver was merged
so people were rolling their own.
The ab8500.c driver contains conversion tables for handling
a thermistor on ADC channels AUX1 and AUX2.
I managed to replace the functionality of the driver with:
- Activation of the ntc_thermistor.c driver,
CONFIG_SENSORS_NTC_THERMISTOR
- Activation of thermal zones, CONFIG_THERMAL
- In the device tree, connecting the NTC driver to the
processed IIO channels from the AB8500 GPADC ADC forming
two instances of NTC sensors.
- Connecting the two NTC sensors to a "chassis" thermal zone
in the device tree and setting that to hit the CPU frequency
at 50 degrees celsius and do a critical shutdown at 70
degrees celsius, deploying a policy using the sensors.
After talking to the original authors we concluded that the
driver was never properly parameterized in production so
what we now have in the device tree is already puts the
thermistors to better use than what the hwmon driver did.
The two remaining channels for two battery temperatures is
already handled in the charging algorithms but can be
optionally extended to thermal zones as well if we want
these to trigger critical shutdown for the platform.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201221125521.768082-1-linus.walleij@linaro.org
[groeck: Removed documentation and fixed up Makefile, Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert the Analog Devices ADM1275 bindings to dt-schema.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201117220807.208747-4-krzk@kernel.org
[groeck: Removed unnecessary type ($ref) declaration]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit b722d7b9e4da ("hwmon: (pmbus) Driver for Delta power supplies
Q54SJ108A2") provides new documentation for DELTA Q54SJ108A2NC* drivers,
but the title underline was too short.
make htmldocs warns:
Documentation/hwmon/q54sj108a2.rst:4: WARNING: Title underline too short.
Adjust the title underline to the correct length.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20201207152658.32444-1-lukas.bulwahn@gmail.com
[groeck: Adjust subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2992 is a rail-to-rail system monitor that
measures current, voltage, and power of two supplies.
Two ADCs simultaneously measure each supply’s current.
A third ADC monitors the input voltages and four
auxiliary external voltages.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver supports Q54SJ108A2 series modules of Delta.
Standard attributes are in sysfs, and other attributes are in debugfs.
Signed-off-by: xiao.ma <xiao.mx.ma@deltaww.com>
Link: https://lore.kernel.org/r/20201202025900.1842-1-max701@126.com
[groeck: Replaced spaces with tabs, dropped excessive spaces,
fixed module prefix in documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the pmbus driver for the STMicroelectronics pm6764 voltage regulator.
the output voltage use the MFR_READ_VOUT 0xD4
vout value returned is linear11
Signed-off-by: Charles Hsu <hsu.yungteng@gmail.com>
[groeck: Fixed various compile errors; marked pm6764tr_of_match __maybe_unused]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Corsair digital power supplies of the series RMi, HXi and AXi include
a small micro-controller with a lot of sensors attached. The sensors can
be accessed by an USB connector from the outside.
This micro-controller provides the data by a simple proprietary USB HID
protocol. The data consist of temperatures, current and voltage levels,
power usage, uptimes, fan speed and some more. It is also possible to
configure the PSU (fan mode, mono/multi-rail, over current protection).
This driver provides access to the sensors/statistics of the RMi and HXi
series power supplies. It does not support configuring these devices,
because there would be many ways to misconfigure or even damage the PSU.
This patch adds:
- hwmon driver corsair-psu
- hwmon documentation
- updates MAINTAINERS
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/20201027131710.GA253280@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The only action currently performed in pmbus_do_remove() is removing the
debugfs hierarchy. We can schedule a devm action at probe time and remove
pmbus_do_remove() entirely from all pmbus drivers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20201026105352.20359-1-brgl@bgdev.pl
[groeck: Removed references to pmbus_do_remove from documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
.../Documentation/hwmon/mp2975.rst:25: WARNING: Unexpected indentation.
.../Documentation/hwmon/mp2975.rst:27: WARNING: Block quote ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst:69: WARNING: Unexpected indentation.
.../Documentation/hwmon/mp2975.rst:70: WARNING: Block quote ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst:72: WARNING: Bullet list ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst: WARNING: document isn't included in any toctree
List blocks should have blank lines before and after them,
in order to be properly parsed.
Fixes: 4beb7a028e9f ("hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/b02f98d886ab1f5af233f8999c7a15529fc52cdc.1603791716.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
New driver and chip support:
- Moortec MR75203 PVT controller
- MPS Multi-phase mp2975 controller
- ADM1266
- Zen3 CPUs
- Intel MAX 10 BMC
Enhancements:
- Support for rated attributes in hwmon core
- MAX20730
- Device monitoring via debugfs
- VOUT readin adjustment vie devicetree bindings
- LM75
- Devicetree support
- Regulator support
- Improved accumulationm logic in amd_energy driver
- Added fan sensor to gsc-hwmon driver
- Support for simplified I2C probing
Various other minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEiHPvMQj9QTOCiqgVyx8mb86fmYEFAl+DpLQACgkQyx8mb86f
mYF+BQ/+NxQsQkSInPakiTq9u1rK9icxjJghn7QmVbFTym3Bzf14bvi88OUu49Cj
10VxbwNQPGDzqWPW3cLOaATclTzAfV3Px35QM/ZiURx4WuEje8XLT/kqh9DtB4il
OhF4q3oXiS5sk4aL6nfNAxsHAiYXpeKj0E5RV1c9chR6tUY9muMcE/DAgUOaIrrX
G6b9o5wXX5nqwcfaoJC0T0jd6mJ3ZCBWqzoIzFoMtAzejN5XOZiQH3sSmW4ZTuVz
GEscC7nqzabtT9R3d5NONyehi9zSJC2+1HByzmQB1/vHoV/1aUV0hq7dyEodGXEl
W5rxIrP1KMe/vKOTg252mbQ+0aXYh0KRy5zywr8rY6G568P1bemZ7K6rH5GHm/Z9
uGXkvhSo2TL0npAhaYvfD+/SFOgzwL5ue9bLByCzUaFClM5o4xmbRf0tKkr/5mRr
LI1GXVMw4Ty++LpaJ6c4Qv+7XizfBIRZ/mJ4QWLpVE+R/Oj0shMrEDQgtLFyukbE
UILkSBtADlY27RNw8K/YEr4/Q33TCLqZWMtqsKhHhOOLMTqtFyzRDx6dTainVUVA
n4KSWDag9jtUy7WbwVuhaTd0ByOz3DVxJELb+ALjBelnwY56H7QUuXZm6uAQRrnE
C7JZ2Ya6KUOwj1xtFan/0pemkHoqv58R4PjpQq/skajCquKk0Ow=
=kwzT
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New driver and chip support:
- Moortec MR75203 PVT controller
- MPS Multi-phase mp2975 controller
- ADM1266
- Zen3 CPUs
- Intel MAX 10 BMC
Enhancements:
- Support for rated attributes in hwmon core
- MAX20730:
- Device monitoring via debugfs
- VOUT readin adjustment vie devicetree bindings
- LM75:
- Devicetree support
- Regulator support
- Improved accumulationm logic in amd_energy driver
- Added fan sensor to gsc-hwmon driver
- Support for simplified I2C probing
Various other minor fixes and improvements"
* tag 'hwmon-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (64 commits)
hwmon: (pmbus/max20730) adjust the vout reading given voltage divider
dt-bindings: hwmon: max20730: adding device tree doc for max20730
hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller
hwmon: Add DT bindings schema for PVT controller
dt-bindings: hwmon: Add the +vs supply to the lm75 bindings
dt-bindings: hwmon: Convert lm75 bindings to yaml
docs: hwmon: (ltc2945) update datasheet link
hwmon: (mlxreg-fan) Fix double "Mellanox"
hwmon: (pmbus/max20730) add device monitoring via debugfs
hwmon: (pmbus/max34440) Fix OC fault limits
hwmon: (bt1-pvt) Wait for the completion with timeout
hwmon: (bt1-pvt) Cache current update timeout
hwmon: (bt1-pvt) Test sensor power supply on probe
hwmon: (lm75) Add regulator support
hwmon: Add hwmon driver for Intel MAX 10 BMC
dt-bindings: Add MP2975 voltage regulator device
hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller
hwmon: (tmp513) fix spelling typo in comments
hwmon: (amd_energy) Update driver documentation
hwmon: (amd_energy) Improve the accumulation logic
...
This patch adds hwmon functionality for Intel MAX 10 BMC chip. This BMC
chip connects to a set of sensor chips to monitor current, voltage,
thermal and power of different components on board. The BMC firmware is
responsible for sensor data sampling and recording in shared registers.
Host driver reads the sensor data from these shared registers and
exposes them to users as hwmon interfaces.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1600669071-26235-3-git-send-email-yilun.xu@intel.com
[groeck: Adjusted subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for mp295 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a dual-loop, digital, multi-phase controller.
This device:
- Supports two power rail.
- Provides 8 pulse-width modulations (PWMs), and can be configured up
to 8-phase operation for rail 1 and up to 4-phase operation for rail
2.
- Supports two pages 0 and 1 for telemetry and also pages 2 and 3 for
configuration.
- Can configured VOUT readout in direct or VID format and allows
setting of different formats on rails 1 and 2. For VID the following
protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
10-mV DAC, IMVP9 mode with 5-mV DAC.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20200926204957.10268-2-vadimp@nvidia.com
[groeck: Cleaned up a couple of error returns; fixed up API changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Update the documentation with the newly added features
* Set the accumulation interval based on resolution
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200929105322.8919-5-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add pmbus probing driver for the adm1266 Cascadable
Super Sequencer with Margin Control and Fault Recording.
Driver is using the pmbus_core, creating sysfs files
under hwmon for inputs: vh1->vh4 and vp1->vp13.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-2-alexandru.tachici@analog.com
[groeck: Use .probe_new function, adjust for changed pmbus_do_probe API]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_do_probe doesn't use the id information provided in its second
argument, so this can be removed, which then allows using the
single-parameter i2c probe function ("probe_new") for probes.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* configured v. probed comparisons are performed by comparing the
configured name to the detected name, instead of the ids; this
involves strcmp but is still cheaper than comparing all the device
names when scanning the tables;
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
Additionally, the mismatch message in the ltc2978 driver is adjusted
so that it no longer assumes that the driver_data is an index into
ltc2978_id.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some drives, reading the drive temperature resets the drive's
spin-down timer. If the drive temperature is read too often, affected
drives will never spin down. Add this information as usage note to
the driver documentation.
Reported-by: Peter Sulyok <peter@sulyok.net>
Cc: Peter Sulyok <peter@sulyok.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding implementation for new attributes (rated_min/rated_max) to
cover PMBus specification about rated values reporting:
MFR_VIN_MIN, MFR_VIN_MAX, MFR_IIN_MAX, MFR_PIN_MAX, MFR_VOUT_MIN,
MFR_VOUT_MAX, MFR_IOUT_MAX, MFR_POUT_MAX, MFR_MAX_TEMP_1/2/3.
Tested with OpenBMC stack. All rated attributes were available
and reported correct values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-4-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
New attributes (rated_min/rated_max) are being added the hwmon ABI.
They are needed to cover rated values documented by PMBus
specification:
PMBus Power System Mgt Protocol Specification - Part II – Revision 1.3.1,
chapters: 22.3.1 - 22.3.10, 22.3.15
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-2-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the hardware monitoring controller of the sl28cpld board
management controller. This driver is part of a multi-function device.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Highlights:
- New driver for Sparx5 SoC temperature sensot
- New driver for Corsair Commander Pro
- MAX20710 support added to max20730 driver
Enhancements:
- max6697: Allow max6581 to create tempX_offset attributes
- gsc (Gateworks System Controller): add 16bit pre-scaled voltage mode
- adm1275: Enable adm1278 ADM1278_TEMP1_EN
- dell-smm: Add Latitude 5480 to fan control whitelist
Fixes:
- adc128d818: Fix advanced configuration register init
- pmbus/core: Use s64 instead of long for calculations
to fix overflow issues with 32-bit architectures
Plus various cleanups in several drivers.
-----BEGIN PGP SIGNATURE-----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=nMNN
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Highlights:
- New driver for Sparx5 SoC temperature sensot
- New driver for Corsair Commander Pro
- MAX20710 support added to max20730 driver
Enhancements:
- max6697: Allow max6581 to create tempX_offset attributes
- gsc (Gateworks System Controller): add 16bit pre-scaled voltage mode
- adm1275: Enable adm1278 ADM1278_TEMP1_EN
- dell-smm: Add Latitude 5480 to fan control whitelist
Fixes:
- adc128d818: Fix advanced configuration register init
- pmbus/core: Use s64 instead of long for calculations to fix
overflow issues with 32-bit architectures
Plus various cleanups in several drivers"
* tag 'hwmon-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (32 commits)
hwmon: (adc128d818) Fix advanced configuration register init
hwmon: (axi-fan-control) remove duplicate macros
hwmon: (i5k_amb, vt8231) Drop uses of pci_read_config_*() return value
hwmon: (sparx5) Make symbol 's5_temp_match' static
hwmon: (corsair-cpro) add reading pwm values
hwmon: sparx5: Add Sparx5 SoC temperature driver
dt-bindings: hwmon: Add Sparx5 temperature sensor
hwmon: (tmp401) Replace HTTP links with HTTPS ones
hwmon: (lm95234) Replace HTTP links with HTTPS ones
hwmon: (lm90) Replace HTTP links with HTTPS ones
hwmon: (k8temp) Replace HTTP links with HTTPS ones
hwmon: (jc42) Replace HTTP links with HTTPS ones
hwmon: (ina2xx) Replace HTTP links with HTTPS ones
hwmon: (ina209) Replace HTTP links with HTTPS ones
hwmon: Replace HTTP links with HTTPS ones
docs: hwmon: Replace HTTP links with HTTPS ones
hwmon: (adm1025) Replace HTTP links with HTTPS ones
hwmon: add Corsair Commander Pro driver
hwmon: (max6697) Allow max6581 to create tempX_offset
hwmon: (tmmp513) Replace HTTP links with HTTPS links
...
Currently, acpi.info is an invalid link to access ACPI specification,
the new valid link is https://uefi.org/specifications.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This adds the possibility for reading pwm values.
These can not be read if the device is controlled via
fan_target or a fan curve and will return an error in
this case. Since an error is expected, this adds some
rudimentary error handling.
Changes:
- add CTL_GET_FAN_PWM and use it via get_data
- pwm returns -ENODATA if the device returns error 0x12
- fan_target now returns -ENODATA when the driver is
started or a pwm value is set.
- add ccp_get_errno to determine errno from device error.
- get_data now has a parameter to determine whether
to read one or two bytes of data.
- update documentation
- fix missing surname in MAINTAINERS
Signed-off-by: Marius Zachmann <mail@mariuszachmann.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719192544.61247-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719191534.61181-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719190525.61112-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719183548.61011-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719182539.60944-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719181530.60878-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719180521.60811-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719175512.60745-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719170420.60399-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is v7 of a driver for the Corsair Commander Pro.
It provides sysfs attributes for:
- Reading fan speed
- Reading temp sensors
- Reading voltage values
- Writing pwm and reading last written pwm
- Reading fan and temp connection status
It is an usb driver, so it needs to be ignored by usbhid.
The Corsair Commander Pro is a fan controller and provides
no means for user interaction.
The two device numbers are there, because there is a slightly
different version of the same device. (Only difference
seem to be in some presets.)
Squashed:
hwmon: (corsair-cpro) add fan_target
This adds fan_target entries to the corsair-cpro driver.
Reading the attribute from the device does not seem possible, so
it returns the last set value (same as pwm).
send_usb_cmd now has one more argument, which is needed for the
fan_target command.
hwmon: corsair-cpro: Change to HID driver
This changes corsair-cpro to a hid driver using hid reports.
Signed-off-by: Marius Zachmann <mail@mariuszachmann.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200626055936.4441-1-mail@mariuszachmann.de
Link: https://lore.kernel.org/r/20200709141413.30790-1-mail@mariuszachmann.de
[groeck: Squashed follow-up patches to avoid changes in HID code]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200703185657.15329-1-grandmaster@al2klimov.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Baikal-T1 SoC provides an embedded process, voltage and temperature
sensor to monitor an internal SoC environment (chip temperature, supply
voltage and process monitor) and on time detect critical situations,
which may cause the system instability and even damages. The IP-block
is based on the Analog Bits PVT sensor, but is equipped with a
dedicated control wrapper, which provides a MMIO registers-based access
to the sensor core functionality (APB3-bus based) and exposes an
additional functions like thresholds/data ready interrupts, its status
and masks, measurements timeout. All of these is used to create a hwmon
driver being added to the kernel by this commit.
The driver implements support for the hardware monitoring capabilities
of Baikal-T1 process, voltage and temperature sensors. PVT IP-core
consists of one temperature and four voltage sensors, each of which is
implemented as a dedicated hwmon channel config.
The driver can optionally provide the hwmon alarms for each sensor the
PVT controller supports. The alarms functionality is made compile-time
configurable due to the hardware interface implementation peculiarity,
which is connected with an ability to convert data from only one sensor
at a time. Additional limitation is that the controller performs the
thresholds checking synchronously with the data conversion procedure.
Due to these limitations in order to have the hwmon alarms
automatically detected the driver code must switch from one sensor to
another, read converted data and manually check the threshold status
bits. Depending on the measurements timeout settings this design may
cause additional burden on the system performance. By default if the
alarms kernel config is disabled the data conversion is performed by
the driver on demand when read operation is requested via corresponding
_input-file.
Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the Maxim MAX6654 to the lm90 driver.
The MAX6654 is a temperature sensor, similar to the others,
but with some differences regarding the configuration
register, and the sampling rate at which extended resolution
becomes possible.
Signed-off-by: Josh Lehan <krellan@google.com>
Link: https://lore.kernel.org/r/20200513184248.145765-1-krellan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX16601 is a VR13.HC Dual-Output Voltage Regulator Chipset,
implementing a (8+1) multiphase synchronous buck converter.
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Implement alert functions for INA226, INA230 and INA231. Expose 06h
Mask/Enable and 07h Alert Limit registers via alert setting and alarm
files.
Signed-off-by: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Gateworks System Controller has a hwmon sub-component that exposes
up to 16 ADC's, some of which are temperature sensors, others which are
voltage inputs. The ADC configuration (register mapping and name) is
configured via device-tree and varies board to board.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PHY supports monitoring its die temperature as well as two analog
voltages. Add support for it.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
I2C chip IDs need to reflect chip names, not chip functionality.
Fixes: f621d61fd5 ("hwmon: (pmbus) add support for 2nd Gen Renesas digital multiphase")
Cc: Grant Peltier <grantpeltier93@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some PMBus chips support multiple phases, and report telemetry such
as input current, output current, or temperature for each phase.
Add support for such chips to the PMBus core.
Start with a maximum of 8 phases per page, and assume that supported
sensors per phase are similar for all pages. Only support per-phase
telemetry attributes, no limits or alarms.
As part of this patch, set the initial page variable to 0xff to ensure
that the page is updated when the first page command is issued. Also
only issue page commands if the chip supports more than one page.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In preparation for multi-phase support, add 'phase' parameter to read_word
and set_page functions. Actual multi-phase support will be added in
a subsequent patch.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.
This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.
With this driver, the hard disk temperature can be read using the
unprivileged 'sensors' application:
$ sensors drivetemp-scsi-1-0
drivetemp-scsi-1-0
Adapter: SCSI adapter
temp1: +23.0°C
or directly from sysfs:
$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000
If the drive supports SCT transport and reports temperature limits,
those are reported as well.
drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1: +27.0°C (low = +0.0°C, high = +60.0°C)
(crit low = -41.0°C, crit = +85.0°C)
(lowest = +23.0°C, highest = +34.0°C)
The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism.
Cc: Chris Healy <cphealy@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
- Various kerneldoc script enhancements.
- More RST conversions; those are slowing down as we run out of things to
convert, but we're a ways from done still.
- Dan's "maintainer profile entry" work landed at last. Now we just need
to get maintainers to fill in the profiles...
- A reworking of the parallel build setup to work better with a variety of
systems (and to not take over huge systems entirely in particular).
- The MAINTAINERS file is now converted to RST during the build.
Hopefully nobody ever tries to print this thing, or they will need to
load a lot of paper.
- A script and documentation making it easy for maintainers to add Link:
tags at commit time.
Also included is the removal of a bunch of spurious CR characters.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl3j5B0PHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YtBcH/jIN2cO8/0YW2rjVT+1G6ytSdFUKx5WJ/lpf
5uBeCvuCeYhtCB6+BgnXvjykJ7jDW11/NJNjWqz/gsvD5l5FJK1rXarI/oz2Klyi
kcPtDmBF/ki4wz9qXzEpa0vg8LXdjeys50S1vE75qCzxZoPP7YjuRbPnLrlIJukv
JbDVi4p9kxgeHfRB4+BHOe5rFwA3mMmaxKNIX34Y+UUO2KZ0g/yUi1bAaQwQAdt+
PsORmkVQ8Puh3K9xRIr7dYlcWBlBiPqzYdvDgTVxSjrxdK6wjYjSgVk2VjC5MBUN
mTSTWgyfsIcD/76/s8tq7ZRl2fw+SkCSkFo79Rb/hJwDTb7Vnng=
=LPBr
-----END PGP SIGNATURE-----
Merge tag 'docs-5.5a' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"Here are the main documentation changes for 5.5:
- Various kerneldoc script enhancements.
- More RST conversions; those are slowing down as we run out of
things to convert, but we're a ways from done still.
- Dan's "maintainer profile entry" work landed at last. Now we just
need to get maintainers to fill in the profiles...
- A reworking of the parallel build setup to work better with a
variety of systems (and to not take over huge systems entirely in
particular).
- The MAINTAINERS file is now converted to RST during the build.
Hopefully nobody ever tries to print this thing, or they will need
to load a lot of paper.
- A script and documentation making it easy for maintainers to add
Link: tags at commit time.
Also included is the removal of a bunch of spurious CR characters"
* tag 'docs-5.5a' of git://git.lwn.net/linux: (91 commits)
docs: remove a bunch of stray CRs
docs: fix up the maintainer profile document
libnvdimm, MAINTAINERS: Maintainer Entry Profile
Maintainer Handbook: Maintainer Entry Profile
MAINTAINERS: Reclaim the P: tag for Maintainer Entry Profile
docs, parallelism: Rearrange how jobserver reservations are made
docs, parallelism: Do not leak blocking mode to other readers
docs, parallelism: Fix failure path and add comment
Documentation: Remove bootmem_debug from kernel-parameters.txt
Documentation: security: core.rst: fix warnings
Documentation/process/howto/kokr: Update for 4.x -> 5.x versioning
Documentation/translation: Use Korean for Korean translation title
docs/memory-barriers.txt: Remove remaining references to mmiowb()
docs/memory-barriers.txt/kokr: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt/kokr: Fix style, spacing and grammar in I/O section
Documentation/kokr: Kill all references to mmiowb()
docs/memory-barriers.txt/kokr: Rewrite "KERNEL I/O BARRIER EFFECTS" section
docs: Add initial documentation for devfreq
Documentation: Document how to get links with git am
docs: Add request_irq() documentation
...
Part of the documentation is taken from the README of the userspace
utils (https://github.com/vitorafsr/i8kutils). The license is GPL-2+
and the author Massimo Dal Zotto is already credited as author of
the module. Therefore there should be no copyright problem.
I also added a paragraph with specific information on the experimental
support for automatic BIOS fan control.
Signed-off-by: Giovanni Mascellani <gio@debian.org>
Link: https://lore.kernel.org/r/20191122101519.1246458-2-gio@debian.org
[groeck: Fixed some of the documentation warnings]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TI's TMP512/513 are I2C/SMBus system monitor chips. These chips
monitor the supply voltage, supply current, power consumption
and provide one local and up to three (TMP513) remote temperature sensors.
It has been tested using a TI TMP513 development kit (TMP513EVM)
Signed-off-by: Eric Tremblay <etremblay@distech-controls.com>
Link: https://lore.kernel.org/r/20191112223001.20844-3-etremblay@distech-controls.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add documentation for bel-pfe pmbus driver which supports BEL PFE1100 and
PFE3000 power supplies.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20191029182054.32279-3-rentao.bupt@gmail.com
[groeck: Added bel-pfe to index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ltc2947 is a high precision power and energy monitor with an
internal sense resistor supporting up to +/- 30A. Three internal no
Latency ADCs ensure accurate measurement of voltage and current, while
high-bandwidth analog multiplication of voltage and current provides
accurate power measurement in a wide range of applications. Internal or
external clocking options enable precise charge and energy measurements.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20191021154115.319073-1-nuno.sa@analog.com
[groeck: Removed unnecessary checks when reading temperature and energy;
PAGE{0,1} -> LTC2947_PAGE_{0,1}]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch implements the summation feature of INA3221, mainly the
SCC (enabling) and SF (warning flag) bits of MASK_ENABLE register,
INA3221_SHUNT_SUM (summation of shunt voltages) register, and the
INA3221_CRIT_SUM (its critical alert setting) register.
Although the summation feature allows user to select which channels
to be added to the result, as an initial support, this patch simply
selects all channels by default, with one only condition: all shunt
resistor values need to be the same. This is because the summation
of current channels can be only accurately calculated, using shunt
voltage sum register, if all shunt resistors are equivalent.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20191016235702.22039-1-nicoleotsuka@gmail.com
[groeck: summation->sum in documentation and label]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl2su/AeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGvm4H/1jkheCrvB/GJS69
wd18vizAg+eFmNCzxlGVhpQTKGymNRy+g6clnoli3cNJ3pSVKcYgVyB3oXaONIhp
g/ANudnBjTdjqYgJzfLij5AGecrGwDpF3YL0kuKrCB63s2I/HwQGYy/aPrYY8emy
gAYdaf1DGRu5/DIIB6soTo/TnpKoAyTE+XY5MaPSug++t/Flov19tlU40IZxXW94
bjTXbm0yklrsIx+LL5mYYGGnygSTCF66JjFg1qhDCBQaS2MZ21h1ZgaOtGZTwZcc
WgEiqLC5S1Iyj96zir1t78RcVQ4RzgvDbhUOgIqUFsYAO2wOicvxyFE3Hj8rPOKd
uGgVPRM=
=xgZa
-----END PGP SIGNATURE-----
Merge tag 'v5.4-rc4' into docs-next
I need to pick up the independent changes made to
Documentation/core-api/memory-allocation.rst to be able to merge further
work without creating a total mess.
There are a number of documentation files that got moved or
renamed. update their references.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Paul Walmsley <paul.walmsley@sifive.com> # RISC-V
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Sphinx is generating a build warning as the title underline
of this file is too short.
Signed-off-by: Adam Zerella <adam.zerella@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When generating documentation output Sphinx
outputs a warning for not including
the page 'inspur-ipsps1.rst' in 'index.rst'.
Assuming this documentation is useful it
should be included in the index.
Signed-off-by: Adam Zerella <adam.zerella@gmail.com>
Link: https://lore.kernel.org/r/20190925131715.GB19073@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It's been a while since the k10temp documentation has been updated.
There are new CPU families supported as well as Tdie temp was added.
This patch adds all missing families which I was able to find from git
history and provides more info about Tctl vs Tdie exported temps.
Signed-off-by: Lukas Zapletal <lzap+git@redhat.com>
Link: https://lore.kernel.org/r/20190923105931.27881-1-lzap+git@redhat.com
[groeck: Formatting]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware support
that was removed in 2004; one doesn't want to rush these things.
- The usual assortment of fixes, typo corrections, etc.
You'll still find a handful of annoying conflicts against other trees,
mostly tied to the last RST conversions; resolutions are straightforward
and the linux-next ones are good.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl1/J4IACgkQF0NaE2wM
flhYogf9EgYozCe8RocSq+JjJpZOSFjIGDQv+GwTjOBIdqgO9tSIaY/p0wSkYKil
jYXyMDF+Xwr8podsUep2F7akBM7j9XJ+XBGJcfOna0ypC9xoejMgWt9fU3YvaWge
dQJxIQ/iwkDlKNx6uOYgKysLUWFS0EP/nzPhqBo4bZZzhugvrR46D/nQqFNmGihd
l9yLalJtP5mC0XRUv3hpdAFFFKxdC0R3BGOel2V+slSClp0LEgpdMAuMaKydEDI3
Ch9ZpIp8fB8kqONCs9/X6083WRsDOMe28KgeGrGHo4Jla6u51QBLQjSVKttFv7xk
051yNJwDWMxgl+A4gyNLDPXM7Gd7HQ==
=v4dp
-----END PGP SIGNATURE-----
Merge tag 'docs-5.4' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"It's a somewhat calmer cycle for docs this time, as the churn of the
mass RST conversion is happily mostly behind us.
- A new document on reproducible builds.
- We finally got around to zapping the documentation for hardware
support that was removed in 2004; one doesn't want to rush these
things.
- The usual assortment of fixes, typo corrections, etc"
* tag 'docs-5.4' of git://git.lwn.net/linux: (67 commits)
Documentation: kbuild: Add document about reproducible builds
docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]
Documentation: Add "earlycon=sbi" to the admin guide
doc🔒 remove reference to clever use of read-write lock
devices.txt: improve entry for comedi (char major 98)
docs: mtd: Update spi nor reference driver
doc: arm64: fix grammar dtb placed in no attributes region
Documentation: sysrq: don't recommend 'S' 'U' before 'B'
mailmap: Update email address for Quentin Perret
docs: ftrace: clarify when tracing is disabled by the trace file
docs: process: fix broken link
Documentation/arm/samsung-s3c24xx: Remove stray U+FEFF character to fix title
Documentation/arm/sa1100/assabet: Fix 'make assabet_defconfig' command
Documentation/arm/sa1100: Remove some obsolete documentation
docs/zh_CN: update Chinese howto.rst for latexdocs making
Documentation: virt: Fix broken reference to virt tree's index
docs: Fix typo on pull requests guide
kernel-doc: Allow anonymous enum
Documentation: sphinx: Don't parse socket() as identifier reference
Documentation: sphinx: Add missing comma to list of strings
...
New driver should use devm_hwmon_device_register_with_info() or
hwmon_device_register_with_info() to register with the hwmon subsystem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the driver to monitor Inspur Power System power supplies
with hwmon over pmbus.
This driver adds sysfs attributes for additional power supply data,
including vendor, model, part_number, serial number,
firmware revision, hardware revision, and psu mode(active/standby).
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190819091509.29276-1-wangzqbj@inspur.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A driver for ADS1015 with more functionality is available in the iio
subsystem.
Remove the hwmon driver as duplicate. If the chip is used for hardware
monitoring, the iio->hwmon bridge should be used.
Cc: Dirk Eibach <eibach@gdsys.de>
Link: https://lore.kernel.org/r/1562004758-13025-1-git-send-email-linux@roeck-us.net
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This document was recently introduced. Convert it to ReST
just like the other hwmon documents, adding it to the hwmon index.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Convert each file at I2C subsystem, renaming them to .rst and
adding to the driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The audience for the Kernel driver-model is clearly Kernel hackers.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> # ice driver changes
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Convert the various documents at the driver-model, preparing
them to be part of the driver-api book.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> # ice
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TMP75B has a different control register, supports 12-bit
resolution and the default conversion rate is 37 Hz.
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On almost all places, we're including ReST files without the
extension.
Let's remove the extension here as well, in order to use just
one standard.
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Those three new drivers were missed on the initial conversion
to ReST format. So:
- Rename them to .rst;
- Add them to the hwmon index.rst index;
- add some blank lines at the "Supported systems:" part, in
order to allow Sphinx to properly identify new lines,
suppressing warnings and avoid it to output some random
lines in bold;
- When multiple authors are involved, change the authors
part to a list, in order to avoid adding blank lines.
- adjust the table cells (one of the tables seemed to be
assuming that tab is 4 positions instead of 8) and add
the table markup.
- be sure that the section markups have the same number of
characters as the section title.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The CONFIG register has two 3-bit fields for conversion time
settings of Bus-voltage and Shunt-voltage, respectively. The
conversion settings, along with averaging mode, allow users
to optimize available timing requirement.
This patch adds an 'update_interval' sysfs node through the
hwmon_chip_info of hwmon core. It reflects a total hardware
conversion time:
samples * channels * (Bus + Shunt conversion times)
Though INA3221 supports different conversion time setups for
Bus and Shunt voltages, this patch only adds the support of
a unified setting for both conversion times, by dividing the
conversion time into two equal values.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
[groeck: .rst related formatting changes in documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now that all files were converted to ReST format, rename them
and add an index.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert all other hwmon files to ReST format, in order to allow
them to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert other files maintained by Guenter to ReST format, in order
to allow them to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert pmbus files to ReST format, in order to allow them to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert k8temp and w83793 to ReST format, in order to allow them
to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert da9052 and da9055 to ReST format, in order to allow
them to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert wm831x and wm8350 to ReST format, in order to allow
them to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert dme1737 and vt1211 to ReST format, in order to allow
them to be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert ads1015 to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert asc7621 to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert ibmpowernv to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert aspeed-pwm-tacho to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert coretemp to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert w83791d to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert fam15h_power to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert pc87360 to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert emc2103 to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert sch5627 to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert menf21bmc to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert vexpress to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert k10temp to ReST format, in order to allow it to
be parsed by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The CONFIG register has a 3-bit averaging mode field for users
to setup the number of samples that are collected and averaged
together. This is very useful to filter noise from sensor data.
This patch adds a 'samples' sysfs node using hwmon_chip_samples
of hwmon core, and updates wait time calculation by taking this
samples value into account.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Intersil ISL68137 is a digital output 7-phase configurable PWM
controller with an AVSBus interface.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Document new ABI attributes: {in,power,curr,temp}_samples and samples.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Delete line indicating the datasheet was not publicly available. This
line was originally present as a default during the write-up and was
subsequently not removed once the datasheet was located.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the pmbus driver for the Infineon ir38064 voltage regulator.
VOUT_MODE is not supported by the device. The driver fakes linear16
mode with exponent value -8.
The device supports VOUT_PEAK, IOUT_PEAK, and TEMPERATURE_PEAK, however
this driver does not enable them.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix the company name from "Infinion" to "Infineon."
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds a short description for the new RPM support of the pwm-fan
driver.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The new HWMON_CHANNEL_INFO macro simplifies the code, reduces the
likelihood of errors, and makes the code easier to read. Add a usage
example to help driver writers to actually use it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
