forked from Minki/linux
[PATCH] ioc4: PCI bus speed detection
Several hardware features of SGI's IOC4 I/O controller chip require timing-related driver calculations dependent upon the PCI bus speed. This patch enables the core IOC4 driver code to detect the actual bus speed and store a value that can later be used by the IOC4 subdrivers as needed. Signed-off-by: Brent Casavant <bcasavan@sgi.com> Acked-by: Pat Gefre <pfg@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This commit is contained in:
Brent Casavant
Linus Torvalds
parent
e5d310b349
commit
d4c477ca54
@ -299,7 +299,6 @@ struct ioc4_serial {
|
||||
} ioc4_serial;
|
||||
|
||||
/* UART clock speed */
|
||||
#define IOC4_SER_XIN_CLK IOC4_SER_XIN_CLK_66
|
||||
#define IOC4_SER_XIN_CLK_66 66666667
|
||||
#define IOC4_SER_XIN_CLK_33 33333333
|
||||
|
||||
@ -1012,21 +1011,20 @@ static irqreturn_t ioc4_intr(int irq, void *arg, struct pt_regs *regs)
|
||||
* ioc4_attach_local - Device initialization.
|
||||
* Called at *_attach() time for each
|
||||
* IOC4 with serial ports in the system.
|
||||
* @control: ioc4_control ptr
|
||||
* @pdev: PCI handle for this device
|
||||
* @soft: soft struct for this device
|
||||
* @ioc4: ioc4 mem space
|
||||
* @idd: Master module data for this IOC4
|
||||
*/
|
||||
static int inline ioc4_attach_local(struct pci_dev *pdev,
|
||||
struct ioc4_control *control,
|
||||
struct ioc4_soft *soft, void __iomem *ioc4_misc,
|
||||
void __iomem *ioc4_serial)
|
||||
static int inline ioc4_attach_local(struct ioc4_driver_data *idd)
|
||||
{
|
||||
struct ioc4_port *port;
|
||||
struct ioc4_port *ports[IOC4_NUM_SERIAL_PORTS];
|
||||
int port_number;
|
||||
uint16_t ioc4_revid_min = 62;
|
||||
uint16_t ioc4_revid;
|
||||
struct pci_dev *pdev = idd->idd_pdev;
|
||||
struct ioc4_control* control = idd->idd_serial_data;
|
||||
struct ioc4_soft *soft = control->ic_soft;
|
||||
void __iomem *ioc4_misc = idd->idd_misc_regs;
|
||||
void __iomem *ioc4_serial = soft->is_ioc4_serial_addr;
|
||||
|
||||
/* IOC4 firmware must be at least rev 62 */
|
||||
pci_read_config_word(pdev, PCI_COMMAND_SPECIAL, &ioc4_revid);
|
||||
@ -1063,7 +1061,15 @@ static int inline ioc4_attach_local(struct pci_dev *pdev,
|
||||
port->ip_ioc4_soft = soft;
|
||||
port->ip_pdev = pdev;
|
||||
port->ip_ienb = 0;
|
||||
port->ip_pci_bus_speed = IOC4_SER_XIN_CLK;
|
||||
/* Use baud rate calculations based on detected PCI
|
||||
* bus speed. Simply test whether the PCI clock is
|
||||
* running closer to 66MHz or 33MHz.
|
||||
*/
|
||||
if (idd->count_period/IOC4_EXTINT_COUNT_DIVISOR < 20) {
|
||||
port->ip_pci_bus_speed = IOC4_SER_XIN_CLK_66;
|
||||
} else {
|
||||
port->ip_pci_bus_speed = IOC4_SER_XIN_CLK_33;
|
||||
}
|
||||
port->ip_baud = 9600;
|
||||
port->ip_control = control;
|
||||
port->ip_mem = ioc4_misc;
|
||||
@ -2733,9 +2739,8 @@ ioc4_serial_attach_one(struct ioc4_driver_data *idd)
|
||||
"%s : request_irq fails for IRQ 0x%x\n ",
|
||||
__FUNCTION__, idd->idd_pdev->irq);
|
||||
}
|
||||
if ((ret = ioc4_attach_local(idd->idd_pdev, control, soft,
|
||||
soft->is_ioc4_misc_addr,
|
||||
soft->is_ioc4_serial_addr)))
|
||||
ret = ioc4_attach_local(idd);
|
||||
if (ret)
|
||||
goto out4;
|
||||
|
||||
/* register port with the serial core */
|
||||
|
||||
@ -6,7 +6,7 @@ menu "SN Devices"
|
||||
|
||||
config SGI_IOC4
|
||||
tristate "SGI IOC4 Base IO support"
|
||||
depends on IA64_GENERIC || IA64_SGI_SN2
|
||||
depends on (IA64_GENERIC || IA64_SGI_SN2) && MMTIMER
|
||||
default m
|
||||
---help---
|
||||
This option enables basic support for the SGI IOC4-based Base IO
|
||||
|
||||
@ -29,7 +29,26 @@
|
||||
#include <linux/module.h>
|
||||
#include <linux/pci.h>
|
||||
#include <linux/ioc4.h>
|
||||
#include <linux/mmtimer.h>
|
||||
#include <linux/rtc.h>
|
||||
#include <linux/rwsem.h>
|
||||
#include <asm/sn/addrs.h>
|
||||
#include <asm/sn/clksupport.h>
|
||||
#include <asm/sn/shub_mmr.h>
|
||||
|
||||
/***************
|
||||
* Definitions *
|
||||
***************/
|
||||
|
||||
/* Tweakable values */
|
||||
|
||||
/* PCI bus speed detection/calibration */
|
||||
#define IOC4_CALIBRATE_COUNT 63 /* Calibration cycle period */
|
||||
#define IOC4_CALIBRATE_CYCLES 256 /* Average over this many cycles */
|
||||
#define IOC4_CALIBRATE_DISCARD 2 /* Discard first few cycles */
|
||||
#define IOC4_CALIBRATE_LOW_MHZ 25 /* Lower bound on bus speed sanity */
|
||||
#define IOC4_CALIBRATE_HIGH_MHZ 75 /* Upper bound on bus speed sanity */
|
||||
#define IOC4_CALIBRATE_DEFAULT_MHZ 66 /* Assumed if sanity check fails */
|
||||
|
||||
/************************
|
||||
* Submodule management *
|
||||
@ -101,6 +120,112 @@ ioc4_unregister_submodule(struct ioc4_submodule *is)
|
||||
* Device management *
|
||||
*********************/
|
||||
|
||||
#define IOC4_CALIBRATE_LOW_LIMIT \
|
||||
(1000*IOC4_EXTINT_COUNT_DIVISOR/IOC4_CALIBRATE_LOW_MHZ)
|
||||
#define IOC4_CALIBRATE_HIGH_LIMIT \
|
||||
(1000*IOC4_EXTINT_COUNT_DIVISOR/IOC4_CALIBRATE_HIGH_MHZ)
|
||||
#define IOC4_CALIBRATE_DEFAULT \
|
||||
(1000*IOC4_EXTINT_COUNT_DIVISOR/IOC4_CALIBRATE_DEFAULT_MHZ)
|
||||
|
||||
#define IOC4_CALIBRATE_END \
|
||||
(IOC4_CALIBRATE_CYCLES + IOC4_CALIBRATE_DISCARD)
|
||||
|
||||
#define IOC4_INT_OUT_MODE_TOGGLE 0x7 /* Toggle INT_OUT every COUNT+1 ticks */
|
||||
|
||||
/* Determines external interrupt output clock period of the PCI bus an
|
||||
* IOC4 is attached to. This value can be used to determine the PCI
|
||||
* bus speed.
|
||||
*
|
||||
* IOC4 has a design feature that various internal timers are derived from
|
||||
* the PCI bus clock. This causes IOC4 device drivers to need to take the
|
||||
* bus speed into account when setting various register values (e.g. INT_OUT
|
||||
* register COUNT field, UART divisors, etc). Since this information is
|
||||
* needed by several subdrivers, it is determined by the main IOC4 driver,
|
||||
* even though the following code utilizes external interrupt registers
|
||||
* to perform the speed calculation.
|
||||
*/
|
||||
static void
|
||||
ioc4_clock_calibrate(struct ioc4_driver_data *idd)
|
||||
{
|
||||
extern unsigned long sn_rtc_cycles_per_second;
|
||||
union ioc4_int_out int_out;
|
||||
union ioc4_gpcr gpcr;
|
||||
unsigned int state, last_state = 1;
|
||||
uint64_t start = 0, end, period;
|
||||
unsigned int count = 0;
|
||||
|
||||
/* Enable output */
|
||||
gpcr.raw = 0;
|
||||
gpcr.fields.dir = IOC4_GPCR_DIR_0;
|
||||
gpcr.fields.int_out_en = 1;
|
||||
writel(gpcr.raw, &idd->idd_misc_regs->gpcr_s.raw);
|
||||
|
||||
/* Reset to power-on state */
|
||||
writel(0, &idd->idd_misc_regs->int_out.raw);
|
||||
mmiowb();
|
||||
|
||||
printk(KERN_INFO
|
||||
"%s: Calibrating PCI bus speed "
|
||||
"for pci_dev %s ... ", __FUNCTION__, pci_name(idd->idd_pdev));
|
||||
/* Set up square wave */
|
||||
int_out.raw = 0;
|
||||
int_out.fields.count = IOC4_CALIBRATE_COUNT;
|
||||
int_out.fields.mode = IOC4_INT_OUT_MODE_TOGGLE;
|
||||
int_out.fields.diag = 0;
|
||||
writel(int_out.raw, &idd->idd_misc_regs->int_out.raw);
|
||||
mmiowb();
|
||||
|
||||
/* Check square wave period averaged over some number of cycles */
|
||||
do {
|
||||
int_out.raw = readl(&idd->idd_misc_regs->int_out.raw);
|
||||
state = int_out.fields.int_out;
|
||||
if (!last_state && state) {
|
||||
count++;
|
||||
if (count == IOC4_CALIBRATE_END) {
|
||||
end = rtc_time();
|
||||
break;
|
||||
} else if (count == IOC4_CALIBRATE_DISCARD)
|
||||
start = rtc_time();
|
||||
}
|
||||
last_state = state;
|
||||
} while (1);
|
||||
|
||||
/* Calculation rearranged to preserve intermediate precision.
|
||||
* Logically:
|
||||
* 1. "end - start" gives us number of RTC cycles over all the
|
||||
* square wave cycles measured.
|
||||
* 2. Divide by number of square wave cycles to get number of
|
||||
* RTC cycles per square wave cycle.
|
||||
* 3. Divide by 2*(int_out.fields.count+1), which is the formula
|
||||
* by which the IOC4 generates the square wave, to get the
|
||||
* number of RTC cycles per IOC4 INT_OUT count.
|
||||
* 4. Divide by sn_rtc_cycles_per_second to get seconds per
|
||||
* count.
|
||||
* 5. Multiply by 1E9 to get nanoseconds per count.
|
||||
*/
|
||||
period = ((end - start) * 1000000000) /
|
||||
(IOC4_CALIBRATE_CYCLES * 2 * (IOC4_CALIBRATE_COUNT + 1)
|
||||
* sn_rtc_cycles_per_second);
|
||||
|
||||
/* Bounds check the result. */
|
||||
if (period > IOC4_CALIBRATE_LOW_LIMIT ||
|
||||
period < IOC4_CALIBRATE_HIGH_LIMIT) {
|
||||
printk("failed. Assuming PCI clock ticks are %d ns.\n",
|
||||
IOC4_CALIBRATE_DEFAULT / IOC4_EXTINT_COUNT_DIVISOR);
|
||||
period = IOC4_CALIBRATE_DEFAULT;
|
||||
} else {
|
||||
printk("succeeded. PCI clock ticks are %ld ns.\n",
|
||||
period / IOC4_EXTINT_COUNT_DIVISOR);
|
||||
}
|
||||
|
||||
/* Remember results. We store the extint clock period rather
|
||||
* than the PCI clock period so that greater precision is
|
||||
* retained. Divide by IOC4_EXTINT_COUNT_DIVISOR to get
|
||||
* PCI clock period.
|
||||
*/
|
||||
idd->count_period = period;
|
||||
}
|
||||
|
||||
/* Adds a new instance of an IOC4 card */
|
||||
static int
|
||||
ioc4_probe(struct pci_dev *pdev, const struct pci_device_id *pci_id)
|
||||
@ -170,6 +295,9 @@ ioc4_probe(struct pci_dev *pdev, const struct pci_device_id *pci_id)
|
||||
pci_write_config_dword(idd->idd_pdev, PCI_COMMAND,
|
||||
pcmd | PCI_COMMAND_PARITY | PCI_COMMAND_SERR);
|
||||
|
||||
/* Determine PCI clock */
|
||||
ioc4_clock_calibrate(idd);
|
||||
|
||||
/* Disable/clear all interrupts. Need to do this here lest
|
||||
* one submodule request the shared IOC4 IRQ, but interrupt
|
||||
* is generated by a different subdevice.
|
||||
|
||||
@ -11,6 +11,14 @@
|
||||
|
||||
#include <linux/interrupt.h>
|
||||
|
||||
/***************
|
||||
* Definitions *
|
||||
***************/
|
||||
|
||||
/* Miscellaneous values inherent to hardware */
|
||||
|
||||
#define IOC4_EXTINT_COUNT_DIVISOR 520 /* PCI clocks per COUNT tick */
|
||||
|
||||
/***********************************
|
||||
* Structures needed by subdrivers *
|
||||
***********************************/
|
||||
@ -119,19 +127,34 @@ struct ioc4_misc_regs {
|
||||
} gppr[8]; /* Generic PIO pins */
|
||||
};
|
||||
|
||||
/* One of these per IOC4
|
||||
*
|
||||
* The idd_serial_data field is present here, even though it's used
|
||||
* solely by the serial subdriver, because the main IOC4 module
|
||||
* properly owns pci_{get,set}_drvdata functionality. This field
|
||||
* allows that subdriver to stash its own drvdata somewhere.
|
||||
*/
|
||||
/* Masks for GPCR DIR pins */
|
||||
#define IOC4_GPCR_DIR_0 0x01 /* External interrupt output */
|
||||
#define IOC4_GPCR_DIR_1 0x02 /* External interrupt input */
|
||||
#define IOC4_GPCR_DIR_2 0x04
|
||||
#define IOC4_GPCR_DIR_3 0x08 /* Keyboard/mouse presence */
|
||||
#define IOC4_GPCR_DIR_4 0x10 /* Ser. port 0 xcvr select (0=232, 1=422) */
|
||||
#define IOC4_GPCR_DIR_5 0x20 /* Ser. port 1 xcvr select (0=232, 1=422) */
|
||||
#define IOC4_GPCR_DIR_6 0x40 /* Ser. port 2 xcvr select (0=232, 1=422) */
|
||||
#define IOC4_GPCR_DIR_7 0x80 /* Ser. port 3 xcvr select (0=232, 1=422) */
|
||||
|
||||
/* Masks for GPCR EDGE pins */
|
||||
#define IOC4_GPCR_EDGE_0 0x01
|
||||
#define IOC4_GPCR_EDGE_1 0x02 /* External interrupt input */
|
||||
#define IOC4_GPCR_EDGE_2 0x04
|
||||
#define IOC4_GPCR_EDGE_3 0x08
|
||||
#define IOC4_GPCR_EDGE_4 0x10
|
||||
#define IOC4_GPCR_EDGE_5 0x20
|
||||
#define IOC4_GPCR_EDGE_6 0x40
|
||||
#define IOC4_GPCR_EDGE_7 0x80
|
||||
|
||||
/* One of these per IOC4 */
|
||||
struct ioc4_driver_data {
|
||||
struct list_head idd_list;
|
||||
unsigned long idd_bar0;
|
||||
struct pci_dev *idd_pdev;
|
||||
const struct pci_device_id *idd_pci_id;
|
||||
struct __iomem ioc4_misc_regs *idd_misc_regs;
|
||||
unsigned long count_period;
|
||||
void *idd_serial_data;
|
||||
};
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user