Merge remote-tracking branch 'regulator/fix/s5m8767' into regulator-linus

Documentation/devicetree/bindings/mfd/max77693.txt

@@ -0,0 +1,55 @@
+Maxim MAX77693 multi-function device
+
+MAX77693 is a Multifunction device with the following submodules:
+- PMIC,
+- CHARGER,
+- LED,
+- MUIC,
+- HAPTIC
+
+It is interfaced to host controller using i2c.
+This document describes the bindings for the mfd device.
+
+Required properties:
+- compatible : Must be "maxim,max77693".
+- reg : Specifies the i2c slave address of PMIC block.
+- interrupts : This i2c device has an IRQ line connected to the main SoC.
+- interrupt-parent :  The parent interrupt controller.
+
+Optional properties:
+- regulators : The regulators of max77693 have to be instantiated under subnod
+  named "regulators" using the following format.
+
+	regulators {
+		regualtor-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER
+		standard regulator constratints[*].
+	};
+
+	[*] refer Documentation/devicetree/bindings/regulator/regulator.txt
+
+Example:
+	max77693@66 {
+		compatible = "maxim,max77693";
+		reg = <0x66>;
+		interrupt-parent = <&gpx1>;
+		interrupts = <5 2>;
+
+		regulators {
+			esafeout@1 {
+				regulator-compatible = "ESAFEOUT1";
+				regulator-name = "ESAFEOUT1";
+				regulator-boot-on;
+			};
+			esafeout@2 {
+				regulator-compatible = "ESAFEOUT2";
+				regulator-name = "ESAFEOUT2";
+				};
+			charger@0 {
+				regulator-compatible = "CHARGER";
+				regulator-name = "CHARGER";
+				regulator-min-microamp = <60000>;
+				regulator-max-microamp = <2580000>;
+					regulator-boot-on;
+			};
+		};
+	};

Documentation/devicetree/bindings/regulator/lp872x.txt

@@ -0,0 +1,160 @@
+Binding for TI/National Semiconductor LP872x Driver
+
+Required properties:
+  - compatible: "ti,lp8720" or "ti,lp8725"
+  - reg: I2C slave address. 0x7d = LP8720, 0x7a = LP8725
+
+Optional properties:
+  - ti,general-config: the value of LP872X_GENERAL_CFG register (u8)
+    (LP8720)
+    bit[2]: BUCK output voltage control by external DVS pin or register
+            1 = external pin, 0 = bit7 of register 08h
+    bit[1]: sleep control by external DVS pin or register
+            1 = external pin, 0 = bit6 of register 08h
+    bit[0]: time step unit(usec). 1 = 25, 0 = 50
+
+    (LP8725)
+    bit[7:6]: time step unit(usec). 00 = 32, 01 = 64, 10 = 128, 11 = 256
+    bit[4]:   BUCK2 enable control. 1 = enable, 0 = disable
+    bit[3]:   BUCK2 output voltage register address. 1 = 0Ah, 0 = 0Bh
+    bit[2]:   BUCK1 output voltage control by external DVS pin or register
+              1 = register 08h, 0 = DVS
+    bit[1]:   LDO sleep control. 1 = sleep mode, 0 = normal
+    bit[0]:   BUCK1 enable control, 1 = enable, 0 = disable
+
+    For more details, please see the datasheet.
+
+  - ti,update-config: define it when LP872X_GENERAL_CFG register should be set
+  - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices.
+  - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2.
+  - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH.
+
+  Sub nodes for regulator_init_data
+    LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck)
+    LP8725 has maximum 9 nodes. (child name: ldo1 ~ 5, lilo1,2 and buck1,2)
+    For more details, please see the following binding document.
+    (Documentation/devicetree/bindings/regulator/regulator.txt)
+
+Datasheet
+  - LP8720: http://www.ti.com/lit/ds/symlink/lp8720.pdf
+  - LP8725: http://www.ti.com/lit/ds/symlink/lp8725.pdf
+
+Example 1) LP8720
+
+lp8720@7d {
+	compatible = "ti,lp8720";
+	reg = <0x7d>;
+
+	/* external DVS pin used, timestep is 25usec */
+	ti,general-config = /bits/ 8 <0x03>;
+	ti,update-config;
+
+	/*
+	 * The dvs-gpio depends on the processor environment.
+	 * For example, following GPIO specifier means GPIO134 in OMAP4.
+	 */
+	ti,dvs-gpio = <&gpio5 6 0>;
+	ti,dvs-vsel = /bits/ 8 <1>;		/* SEL_V2 */
+	ti,dvs-state = /bits/ 8 <1>;		/* DVS_HIGH */
+
+	vaf: ldo1 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vmmc: ldo2 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcam_io: ldo3 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+
+	vcam_core: ldo4 {
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <2850000>;
+		regulator-boot-on;
+	};
+
+	vcam: ldo5 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc: buck {
+		regulator-name = "VBUCK";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <2300000>;
+	};
+};
+
+Example 2) LP8725
+
+lp8725@7a {
+	compatible = "ti,lp8725";
+	reg = <0x7a>;
+
+	/* Enable BUCK1,2, no DVS, normal LDO mode, timestep is 256usec */
+	ti,general-config = /bits/ 8 <0xdd>;
+	ti,update-config;
+
+	vcam_io: ldo1 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcam_core: ldo2 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcam: ldo3 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcmmb_io: ldo4 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+
+	vcmmb_core: ldo5 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+
+	vaux1: lilo1 {
+		regulator-name = "VAUX1";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vaux2: lilo2 {
+		regulator-name = "VAUX2";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc1: buck1 {
+		regulator-name = "VBUCK1";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <3000000>;
+		regulator-min-microamp  = <460000>;
+		regulator-max-microamp  = <1370000>;
+		regulator-boot-on;
+	};
+
+	vcc2: buck2 {
+		regulator-name = "VBUCK2";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <3000000>;
+		regulator-min-microamp  = <460000>;
+		regulator-max-microamp  = <1370000>;
+		regulator-boot-on;
+	};
+};

Documentation/devicetree/bindings/regulator/max8973-regulator.txt

@@ -0,0 +1,21 @@
+* Maxim MAX8973 Voltage Regulator
+
+Required properties:
+
+- compatible:	must be "maxim,max8973"
+- reg:		the i2c slave address of the regulator. It should be 0x1b.
+
+Any standard regulator properties can be used to configure the single max8973
+DCDC.
+
+Example:
+
+	max8973@1b {
+		compatible = "maxim,max8973";
+		reg = <0x1b>;
+
+		regulator-min-microvolt = <935000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};

Documentation/devicetree/bindings/regulator/regulator.txt

@@ -9,6 +9,7 @@ Optional properties:
 - regulator-max-microamp: largest current consumers may set
 - regulator-always-on: boolean, regulator should never be disabled
 - regulator-boot-on: bootloader/firmware enabled regulator
+- regulator-allow-bypass: allow the regulator to go into bypass mode
 - <name>-supply: phandle to the parent supply/regulator node
 - regulator-ramp-delay: ramp delay for regulator(in uV/uS)
 

Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt

@@ -1,6 +1,6 @@
 * Samsung S5M8767 Voltage and Current Regulator
 
-The Samsung S5M8767 is a multi-function device which includes volatage and
+The Samsung S5M8767 is a multi-function device which includes voltage and
 current regulators, rtc, charger controller and other sub-blocks. It is
 interfaced to the host controller using a i2c interface. Each sub-block is
 addressed by the host system using different i2c slave address. This document
@@ -103,13 +103,13 @@ Example:
 
 		s5m8767,pmic-buck-default-dvs-idx = <0>;
 
-		s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 1 0 0>, /* DVS1 */
+		s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */
-						 <&gpx0 1 1 0 0>, /* DVS2 */
+						 <&gpx0 1 0>, /* DVS2 */
-						 <&gpx0 2 1 0 0>; /* DVS3 */
+						 <&gpx0 2 0>; /* DVS3 */
 
-		s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>, /* SET1 */
+		s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */
-						<&gpx2 4 1 0 0>, /* SET2 */
+						<&gpx2 4 0>, /* SET2 */
-						<&gpx2 5 1 0 0>; /* SET3 */
+						<&gpx2 5 0>; /* SET3 */
 
 		s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
 						 <1250000>, <1200000>,

Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt

@@ -0,0 +1,128 @@
+Adaptive Body Bias(ABB) SoC internal LDO regulator for Texas Instruments SoCs
+
+Required Properties:
+- compatible: Should be one of:
+  - "ti,abb-v1" for older SoCs like OMAP3
+  - "ti,abb-v2" for newer SoCs like OMAP4, OMAP5
+- reg: Address and length of the register set for the device. It contains
+  the information of registers in the same order as described by reg-names
+- reg-names: Should contain the reg names
+  - "base-address"	- contains base address of ABB module
+  - "int-address"	- contains address of interrupt register for ABB module
+  (also see Optional properties)
+- #address-cell: should be 0
+- #size-cell: should be 0
+- clocks: should point to the clock node used by ABB module
+- ti,settling-time: Settling time in uSecs from SoC documentation for ABB module
+	to settle down(target time for SR2_WTCNT_VALUE).
+- ti,clock-cycles: SoC specific data about count of system ti,clock-cycles used for
+	computing settling time from SoC Documentation for ABB module(clock
+	cycles for SR2_WTCNT_VALUE).
+- ti,tranxdone-status-mask: Mask to the int-register to write-to-clear mask
+	indicating LDO tranxdone (operation complete).
+- ti,abb_info: An array of 6-tuples u32 items providing information about ABB
+	configuration needed per operational voltage of the device.
+	Each item consists of the following in the same order:
+	volt: voltage in uV - Only used to index ABB information.
+	ABB mode: one of the following:
+		0-bypass
+		1-Forward Body Bias(FBB)
+		3-Reverse Body Bias(RBB)
+	efuse:	(see Optional properties)
+	RBB enable efuse Mask:	(See Optional properties)
+	FBB enable efuse Mask:	(See Optional properties)
+	Vset value efuse Mask:	(See Optional properties)
+
+	NOTE: If more than 1 entry is present, then regulator is setup to change
+	      voltage, allowing for various modes to be selected indexed off
+	      the regulator. Further, ABB LDOs are considered always-on by
+	      default.
+
+Optional Properties:
+- reg-names: In addition to the required properties, the following are optional
+  - "efuse-address"	- Contains efuse base address used to pick up ABB info.
+  - "ldo-address"	- Contains address of ABB LDO overide register address.
+	"efuse-address" is required for this.
+- ti,ldovbb-vset-mask	- Required if ldo-address is set, mask for LDO override
+	register to provide override vset value.
+- ti,ldovbb-override-mask - Required if ldo-address is set, mask for LDO
+	override register to enable override vset value.
+- ti,abb_opp_sel: Addendum to the description in required properties
+	efuse: Mandatory if 'efuse-address' register is defined. Provides offset
+	       from efuse-address to pick up ABB characteristics. Set to 0 if
+	       'efuse-address' is not defined.
+	RBB enable efuse Mask:	Optional if 'efuse-address' register is defined.
+		'ABB mode' is force set to RBB mode if value at "efuse-address"
+		+ efuse maps to RBB mask. Set to 0 to ignore this.
+	FBB enable efuse Mask:	Optional if 'efuse-address' register is defined.
+		'ABB mode' is force set to FBB mode if value at "efuse-address"
+		+ efuse maps to FBB mask (valid only if RBB mask does not match)
+		Set to 0 to ignore this.
+	Vset value efuse Mask:	Mandatory if ldo-address is set. Picks up from
+		efuse the value to set in 'ti,ldovbb-vset-mask' at ldo-address.
+
+Example #1: Simplest configuration (no efuse data, hard coded ABB table):
+abb_x: regulator-abb-x {
+	compatible = "ti,abb-v1";
+	regulator-name = "abb_x";
+	#address-cell = <0>;
+	#size-cells = <0>;
+	reg = <0x483072f0 0x8>, <0x48306818 0x4>;
+	reg-names = "base-address", "int-address";
+	ti,tranxdone-status-mask = <0x4000000>;
+	clocks = <&sysclk>;
+	ti,settling-time = <30>;
+	ti,clock-cycles = <8>;
+	ti,abb_info = <
+	/* uV		ABB	efuse	rbb_m	fbb_m	vset_m */
+	1012500		0	0	0	0	0 /* Bypass */
+	1200000		3	0	0	0	0 /* RBB mandatory */
+	1320000		1	0	0	0	0 /* FBB mandatory */
+	>;
+};
+
+Example #2: Efuse bits contain ABB mode setting (no LDO override capability)
+abb_y: regulator-abb-y {
+	compatible = "ti,abb-v2";
+	regulator-name = "abb_y";
+	#address-cell = <0>;
+	#size-cells = <0>;
+	reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>, <0x4A002268 0x8>;
+	reg-names = "base-address", "int-address", "efuse-address";
+	ti,tranxdone-status-mask = <0x4000000>;
+	clocks = <&sysclk>;
+	ti,settling-time = <50>;
+	ti,clock-cycles = <16>;
+	ti,abb_info = <
+	/* uV		ABB	efuse	rbb_m	fbb_m	vset_m */
+	975000		0	0	0	0	0 /* Bypass */
+	1012500		0	0	0x40000	0	0 /* RBB optional */
+	1200000		0	0x4	0	0x40000	0 /* FBB optional */
+	1320000		1	0	0	0	0 /* FBB mandatory */
+	>;
+};
+
+Example #3: Efuse bits contain ABB mode setting and LDO override capability
+abb_z: regulator-abb-z {
+	compatible = "ti,abb-v2";
+	regulator-name = "abb_z";
+	#address-cell = <0>;
+	#size-cells = <0>;
+	reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>,
+	      <0x4a002194 0x8>, <0x4ae0C314 0x4>;
+	reg-names = "base-address", "int-address",
+		    "efuse-address", "ldo-address";
+	ti,tranxdone-status-mask = <0x8000000>;
+	/* LDOVBBMM_MUX_CTRL */
+	ti,ldovbb-override-mask = <0x400>;
+	/* LDOVBBMM_VSET_OUT */
+	ti,ldovbb-vset-mask = <0x1F>;
+	clocks = <&sysclk>;
+	ti,settling-time = <50>;
+	ti,clock-cycles = <16>;
+	ti,abb_info = <
+	/* uV	ABB	efuse	rbb_m	fbb_m	vset_m */
+	975000	0	0	0	0	0	/* Bypass */
+	1200000	0	0x4	0	0x40000	0x1f00	/* FBB optional, vset */
+	>;
+};

drivers/regulator/88pm8607.c

@@ -406,7 +406,6 @@ static int pm8607_regulator_remove(struct platform_device *pdev)
 {
 	struct pm8607_regulator_info *info = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
 	regulator_unregister(info->regulator);
 	return 0;
 }

drivers/regulator/Kconfig

@@ -250,6 +250,15 @@ config REGULATOR_MAX77686
 	  via I2C bus. The provided regulator is suitable for
 	  Exynos-4 chips to control VARM and VINT voltages.
 
+config REGULATOR_MAX77693
+	tristate "Maxim MAX77693 regulator"
+	depends on MFD_MAX77693
+	help
+	  This driver controls a Maxim 77693 regulator via I2C bus.
+	  The regulators include two LDOs, 'SAFEOUT1', 'SAFEOUT2'
+	  and one current regulator 'CHARGER'. This is suitable for
+	  Exynos-4x12 chips.
+
 config REGULATOR_PCAP
 	tristate "Motorola PCAP2 regulator driver"
 	depends on EZX_PCAP
@@ -472,6 +481,16 @@ config REGULATOR_TWL4030
 	  This driver supports the voltage regulators provided by
 	  this family of companion chips.
 
+config REGULATOR_TI_ABB
+	bool "TI Adaptive Body Bias on-chip LDO"
+	depends on ARCH_OMAP
+	help
+	  Select this option to support Texas Instruments' on-chip Adaptive Body
+	  Bias (ABB) LDO regulators. It is recommended that this option be
+	  enabled on required TI SoC. Certain Operating Performance Points
+	  on TI SoCs may be unstable without enabling this as it provides
+	  device specific optimized bias to allow/optimize functionality.
+
 config REGULATOR_VEXPRESS
 	tristate "Versatile Express regulators"
 	depends on VEXPRESS_CONFIG

drivers/regulator/Makefile

@@ -12,7 +12,7 @@ obj-$(CONFIG_REGULATOR_USERSPACE_CONSUMER) += userspace-consumer.o
 obj-$(CONFIG_REGULATOR_88PM8607) += 88pm8607.o
 obj-$(CONFIG_REGULATOR_AAT2870) += aat2870-regulator.o
 obj-$(CONFIG_REGULATOR_AB3100) += ab3100.o
-obj-$(CONFIG_REGULATOR_AB8500)	+= ab8500.o ab8500-ext.o
+obj-$(CONFIG_REGULATOR_AB8500)	+= ab8500-ext.o ab8500.o
 obj-$(CONFIG_REGULATOR_AD5398) += ad5398.o
 obj-$(CONFIG_REGULATOR_ANATOP) += anatop-regulator.o
 obj-$(CONFIG_REGULATOR_ARIZONA) += arizona-micsupp.o arizona-ldo1.o
@@ -41,6 +41,7 @@ obj-$(CONFIG_REGULATOR_MAX8973) += max8973-regulator.o
 obj-$(CONFIG_REGULATOR_MAX8997) += max8997.o
 obj-$(CONFIG_REGULATOR_MAX8998) += max8998.o
 obj-$(CONFIG_REGULATOR_MAX77686) += max77686.o
+obj-$(CONFIG_REGULATOR_MAX77693) += max77693.o
 obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
 obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
 obj-$(CONFIG_REGULATOR_MC13XXX_CORE) +=  mc13xxx-regulator-core.o
@@ -63,6 +64,7 @@ obj-$(CONFIG_REGULATOR_TPS65910) += tps65910-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65912) += tps65912-regulator.o
 obj-$(CONFIG_REGULATOR_TPS80031) += tps80031-regulator.o
 obj-$(CONFIG_REGULATOR_TWL4030) += twl-regulator.o
+obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o
 obj-$(CONFIG_REGULATOR_VEXPRESS) += vexpress.o
 obj-$(CONFIG_REGULATOR_WM831X) += wm831x-dcdc.o
 obj-$(CONFIG_REGULATOR_WM831X) += wm831x-isink.o

drivers/regulator/ab8500-ext.c

@@ -16,9 +16,11 @@
 #include <linux/kernel.h>
 #include <linux/err.h>
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
 #include <linux/mfd/abx500.h>
 #include <linux/mfd/abx500/ab8500.h>
 #include <linux/regulator/ab8500.h>
@@ -229,6 +231,28 @@ static unsigned int ab8500_ext_regulator_get_mode(struct regulator_dev *rdev)
 	return ret;
 }
 
+static int ab8500_ext_set_voltage(struct regulator_dev *rdev, int min_uV,
+				  int max_uV, unsigned *selector)
+{
+	struct regulation_constraints *regu_constraints = rdev->constraints;
+
+	if (!regu_constraints) {
+		dev_err(rdev_get_dev(rdev), "No regulator constraints\n");
+		return -EINVAL;
+	}
+
+	if (regu_constraints->min_uV == min_uV &&
+	    regu_constraints->max_uV == max_uV)
+		return 0;
+
+	dev_err(rdev_get_dev(rdev),
+		"Requested min %duV max %duV != constrained min %duV max %duV\n",
+		min_uV, max_uV,
+		regu_constraints->min_uV, regu_constraints->max_uV);
+
+	return -EINVAL;
+}
+
 static int ab8500_ext_list_voltage(struct regulator_dev *rdev,
 				   unsigned selector)
 {
@@ -252,6 +276,7 @@ static struct regulator_ops ab8500_ext_regulator_ops = {
 	.is_enabled		= ab8500_ext_regulator_is_enabled,
 	.set_mode		= ab8500_ext_regulator_set_mode,
 	.get_mode		= ab8500_ext_regulator_get_mode,
+	.set_voltage		= ab8500_ext_set_voltage,
 	.list_voltage		= ab8500_ext_list_voltage,
 };
 
@@ -310,18 +335,37 @@ static struct ab8500_ext_regulator_info
 	},
 };
 
-int ab8500_ext_regulator_init(struct platform_device *pdev)
+static struct of_regulator_match ab8500_ext_regulator_match[] = {
+	{ .name = "ab8500_ext1", .driver_data = (void *) AB8500_EXT_SUPPLY1, },
+	{ .name = "ab8500_ext2", .driver_data = (void *) AB8500_EXT_SUPPLY2, },
+	{ .name = "ab8500_ext3", .driver_data = (void *) AB8500_EXT_SUPPLY3, },
+};
+
+static int ab8500_ext_regulator_probe(struct platform_device *pdev)
 {
 	struct ab8500 *ab8500 = dev_get_drvdata(pdev->dev.parent);
 	struct ab8500_platform_data *ppdata;
 	struct ab8500_regulator_platform_data *pdata;
+	struct device_node *np = pdev->dev.of_node;
 	struct regulator_config config = { };
 	int i, err;
 
+	if (np) {
+		err = of_regulator_match(&pdev->dev, np,
+					 ab8500_ext_regulator_match,
+					 ARRAY_SIZE(ab8500_ext_regulator_match));
+		if (err < 0) {
+			dev_err(&pdev->dev,
+				"Error parsing regulator init data: %d\n", err);
+			return err;
+		}
+	}
+
 	if (!ab8500) {
 		dev_err(&pdev->dev, "null mfd parent\n");
 		return -EINVAL;
 	}
+
 	ppdata = dev_get_platdata(ab8500->dev);
 	if (!ppdata) {
 		dev_err(&pdev->dev, "null parent pdata\n");
@@ -362,8 +406,11 @@ int ab8500_ext_regulator_init(struct platform_device *pdev)
 			pdata->ext_regulator[i].driver_data;
 
 		config.dev = &pdev->dev;
-		config.init_data = &pdata->ext_regulator[i];
 		config.driver_data = info;
+		config.of_node = ab8500_ext_regulator_match[i].of_node;
+		config.init_data = (np) ?
+			ab8500_ext_regulator_match[i].init_data :
+			&pdata->ext_regulator[i];
 
 		/* register regulator with framework */
 		info->rdev = regulator_register(&info->desc, &config);
@@ -386,7 +433,7 @@ int ab8500_ext_regulator_init(struct platform_device *pdev)
 	return 0;
 }
 
-void ab8500_ext_regulator_exit(struct platform_device *pdev)
+static int ab8500_ext_regulator_remove(struct platform_device *pdev)
 {
 	int i;
 
@@ -399,8 +446,37 @@ void ab8500_ext_regulator_exit(struct platform_device *pdev)
 
 		regulator_unregister(info->rdev);
 	}
+
+	return 0;
 }
 
+static struct platform_driver ab8500_ext_regulator_driver = {
+	.probe = ab8500_ext_regulator_probe,
+	.remove = ab8500_ext_regulator_remove,
+	.driver         = {
+		.name   = "ab8500-ext-regulator",
+		.owner  = THIS_MODULE,
+	},
+};
+
+static int __init ab8500_ext_regulator_init(void)
+{
+	int ret;
+
+	ret = platform_driver_register(&ab8500_ext_regulator_driver);
+	if (ret)
+		pr_err("Failed to register ab8500 ext regulator: %d\n", ret);
+
+	return ret;
+}
+subsys_initcall(ab8500_ext_regulator_init);
+
+static void __exit ab8500_ext_regulator_exit(void)
+{
+	platform_driver_unregister(&ab8500_ext_regulator_driver);
+}
+module_exit(ab8500_ext_regulator_exit);
+
 MODULE_LICENSE("GPL v2");
 MODULE_AUTHOR("Bengt Jonsson <bengt.g.jonsson@stericsson.com>");
 MODULE_DESCRIPTION("AB8500 external regulator driver");

drivers/regulator/ab8500.c

@@ -719,6 +719,7 @@ static struct ab8500_regulator_info
 			.n_voltages	= ARRAY_SIZE(ldo_vauxn_voltages),
 			.volt_table	= ldo_vauxn_voltages,
 			.enable_time	= 200,
+			.supply_name    = "vin",
 		},
 		.load_lp_uA		= 5000,
 		.update_bank		= 0x04,
@@ -741,6 +742,7 @@ static struct ab8500_regulator_info
 			.n_voltages	= ARRAY_SIZE(ldo_vauxn_voltages),
 			.volt_table	= ldo_vauxn_voltages,
 			.enable_time	= 200,
+			.supply_name    = "vin",
 		},
 		.load_lp_uA		= 5000,
 		.update_bank		= 0x04,
@@ -763,6 +765,7 @@ static struct ab8500_regulator_info
 			.n_voltages	= ARRAY_SIZE(ldo_vaux3_voltages),
 			.volt_table	= ldo_vaux3_voltages,
 			.enable_time	= 450,
+			.supply_name    = "vin",
 		},
 		.load_lp_uA		= 5000,
 		.update_bank		= 0x04,
@@ -3156,22 +3159,12 @@ static int ab8500_regulator_probe(struct platform_device *pdev)
 			return err;
 	}
 
-	if (!is_ab8505(ab8500)) {
-		/* register external regulators (before Vaux1, 2 and 3) */
-		err = ab8500_ext_regulator_init(pdev);
-		if (err)
-			return err;
-	}
-
 	/* register all regulators */
 	for (i = 0; i < abx500_regulator.info_size; i++) {
 		err = ab8500_regulator_register(pdev, &pdata->regulator[i],
 						i, NULL);
-		if (err < 0) {
+		if (err < 0)
-			if (!is_ab8505(ab8500))
-				ab8500_ext_regulator_exit(pdev);
 			return err;
-		}
 	}
 
 	return 0;
@@ -3180,7 +3173,6 @@ static int ab8500_regulator_probe(struct platform_device *pdev)
 static int ab8500_regulator_remove(struct platform_device *pdev)
 {
 	int i, err;
-	struct ab8500 *ab8500 = dev_get_drvdata(pdev->dev.parent);
 
 	for (i = 0; i < abx500_regulator.info_size; i++) {
 		struct ab8500_regulator_info *info = NULL;
@@ -3192,10 +3184,6 @@ static int ab8500_regulator_remove(struct platform_device *pdev)
 		regulator_unregister(info->regulator);
 	}
 
-	/* remove external regulators (after Vaux1, 2 and 3) */
-	if (!is_ab8505(ab8500))
-		ab8500_ext_regulator_exit(pdev);
-
 	/* remove regulator debug */
 	err = ab8500_regulator_debug_exit(pdev);
 	if (err)

drivers/regulator/core.c

@@ -2137,6 +2137,21 @@ int regulator_list_voltage(struct regulator *regulator, unsigned selector)
 }
 EXPORT_SYMBOL_GPL(regulator_list_voltage);
 
+/**
+ * regulator_get_linear_step - return the voltage step size between VSEL values
+ * @regulator: regulator source
+ *
+ * Returns the voltage step size between VSEL values for linear
+ * regulators, or return 0 if the regulator isn't a linear regulator.
+ */
+unsigned int regulator_get_linear_step(struct regulator *regulator)
+{
+	struct regulator_dev *rdev = regulator->rdev;
+
+	return rdev->desc->uV_step;
+}
+EXPORT_SYMBOL_GPL(regulator_get_linear_step);
+
 /**
  * regulator_is_supported_voltage - check if a voltage range can be supported
  *

drivers/regulator/isl6271a-regulator.c

@@ -130,7 +130,7 @@ static int isl6271a_probe(struct i2c_client *i2c,
 		if (i == 0)
 			config.init_data = init_data;
 		else
-			config.init_data = 0;
+			config.init_data = NULL;
 		config.driver_data = pmic;
 
 		pmic->rdev[i] = regulator_register(&isl_rd[i], &config);

drivers/regulator/lp3971.c

@@ -434,7 +434,7 @@ static int lp3971_i2c_probe(struct i2c_client *i2c,
 		return -ENODEV;
 	}
 
-	lp3971 = kzalloc(sizeof(struct lp3971), GFP_KERNEL);
+	lp3971 = devm_kzalloc(&i2c->dev, sizeof(struct lp3971), GFP_KERNEL);
 	if (lp3971 == NULL)
 		return -ENOMEM;
 
@@ -449,19 +449,15 @@ static int lp3971_i2c_probe(struct i2c_client *i2c,
 		ret = -ENODEV;
 	if (ret < 0) {
 		dev_err(&i2c->dev, "failed to detect device\n");
-		goto err_detect;
+		return ret;
 	}
 
 	ret = setup_regulators(lp3971, pdata);
 	if (ret < 0)
-		goto err_detect;
+		return ret;
 
 	i2c_set_clientdata(i2c, lp3971);
 	return 0;
-
-err_detect:
-	kfree(lp3971);
-	return ret;
 }
 
 static int lp3971_i2c_remove(struct i2c_client *i2c)
@@ -473,7 +469,6 @@ static int lp3971_i2c_remove(struct i2c_client *i2c)
 		regulator_unregister(lp3971->rdev[i]);
 
 	kfree(lp3971->rdev);
-	kfree(lp3971);
 
 	return 0;
 }

drivers/regulator/lp3972.c

@@ -528,7 +528,7 @@ static int lp3972_i2c_probe(struct i2c_client *i2c,
 		return -ENODEV;
 	}
 
-	lp3972 = kzalloc(sizeof(struct lp3972), GFP_KERNEL);
+	lp3972 = devm_kzalloc(&i2c->dev, sizeof(struct lp3972), GFP_KERNEL);
 	if (!lp3972)
 		return -ENOMEM;
 
@@ -546,19 +546,15 @@ static int lp3972_i2c_probe(struct i2c_client *i2c,
 	}
 	if (ret < 0) {
 		dev_err(&i2c->dev, "failed to detect device. ret = %d\n", ret);
-		goto err_detect;
+		return ret;
 	}
 
 	ret = setup_regulators(lp3972, pdata);
 	if (ret < 0)
-		goto err_detect;
+		return ret;
 
 	i2c_set_clientdata(i2c, lp3972);
 	return 0;
-
-err_detect:
-	kfree(lp3972);
-	return ret;
 }
 
 static int lp3972_i2c_remove(struct i2c_client *i2c)
@@ -569,7 +565,6 @@ static int lp3972_i2c_remove(struct i2c_client *i2c)
 	for (i = 0; i < lp3972->num_regulators; i++)
 		regulator_unregister(lp3972->rdev[i]);
 	kfree(lp3972->rdev);
-	kfree(lp3972);
 
 	return 0;
 }

drivers/regulator/lp872x.c

@@ -18,6 +18,9 @@
 #include <linux/regulator/lp872x.h>
 #include <linux/regulator/driver.h>
 #include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/regulator/of_regulator.h>
 
 /* Registers : LP8720/8725 shared */
 #define LP872X_GENERAL_CFG		0x00
@@ -723,8 +726,8 @@ static int lp872x_init_dvs(struct lp872x *lp)
 
 	gpio = dvs->gpio;
 	if (!gpio_is_valid(gpio)) {
-		dev_err(lp->dev, "invalid gpio: %d\n", gpio);
+		dev_warn(lp->dev, "invalid gpio: %d\n", gpio);
-		return -EINVAL;
+		goto set_default_dvs_mode;
 	}
 
 	pinstate = dvs->init_state;
@@ -829,6 +832,103 @@ static const struct regmap_config lp872x_regmap_config = {
 	.max_register = MAX_REGISTERS,
 };
 
+#ifdef CONFIG_OF
+
+#define LP872X_VALID_OPMODE	(REGULATOR_MODE_FAST | REGULATOR_MODE_NORMAL)
+
+static struct of_regulator_match lp8720_matches[] = {
+	{ .name = "ldo1", .driver_data = (void *)LP8720_ID_LDO1, },
+	{ .name = "ldo2", .driver_data = (void *)LP8720_ID_LDO2, },
+	{ .name = "ldo3", .driver_data = (void *)LP8720_ID_LDO3, },
+	{ .name = "ldo4", .driver_data = (void *)LP8720_ID_LDO4, },
+	{ .name = "ldo5", .driver_data = (void *)LP8720_ID_LDO5, },
+	{ .name = "buck", .driver_data = (void *)LP8720_ID_BUCK, },
+};
+
+static struct of_regulator_match lp8725_matches[] = {
+	{ .name = "ldo1", .driver_data = (void *)LP8725_ID_LDO1, },
+	{ .name = "ldo2", .driver_data = (void *)LP8725_ID_LDO2, },
+	{ .name = "ldo3", .driver_data = (void *)LP8725_ID_LDO3, },
+	{ .name = "ldo4", .driver_data = (void *)LP8725_ID_LDO4, },
+	{ .name = "ldo5", .driver_data = (void *)LP8725_ID_LDO5, },
+	{ .name = "lilo1", .driver_data = (void *)LP8725_ID_LILO1, },
+	{ .name = "lilo2", .driver_data = (void *)LP8725_ID_LILO2, },
+	{ .name = "buck1", .driver_data = (void *)LP8725_ID_BUCK1, },
+	{ .name = "buck2", .driver_data = (void *)LP8725_ID_BUCK2, },
+};
+
+static struct lp872x_platform_data
+*lp872x_populate_pdata_from_dt(struct device *dev, enum lp872x_id which)
+{
+	struct device_node *np = dev->of_node;
+	struct lp872x_platform_data *pdata;
+	struct of_regulator_match *match;
+	struct regulator_init_data *d;
+	int num_matches;
+	int count;
+	int i;
+	u8 dvs_state;
+
+	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		goto out;
+
+	of_property_read_u8(np, "ti,general-config", &pdata->general_config);
+	if (of_find_property(np, "ti,update-config", NULL))
+		pdata->update_config = true;
+
+	pdata->dvs = devm_kzalloc(dev, sizeof(struct lp872x_dvs), GFP_KERNEL);
+	if (!pdata->dvs)
+		goto out;
+
+	pdata->dvs->gpio = of_get_named_gpio(np, "ti,dvs-gpio", 0);
+	of_property_read_u8(np, "ti,dvs-vsel", (u8 *)&pdata->dvs->vsel);
+	of_property_read_u8(np, "ti,dvs-state", &dvs_state);
+	pdata->dvs->init_state = dvs_state ? DVS_HIGH : DVS_LOW;
+
+	if (of_get_child_count(np) == 0)
+		goto out;
+
+	switch (which) {
+	case LP8720:
+		match = lp8720_matches;
+		num_matches = ARRAY_SIZE(lp8720_matches);
+		break;
+	case LP8725:
+		match = lp8725_matches;
+		num_matches = ARRAY_SIZE(lp8725_matches);
+		break;
+	default:
+		goto out;
+	}
+
+	count = of_regulator_match(dev, np, match, num_matches);
+	if (count <= 0)
+		goto out;
+
+	for (i = 0; i < num_matches; i++) {
+		pdata->regulator_data[i].id = (int)match[i].driver_data;
+		pdata->regulator_data[i].init_data = match[i].init_data;
+
+		/* Operation mode configuration for buck/buck1/buck2 */
+		if (strncmp(match[i].name, "buck", 4))
+			continue;
+
+		d = pdata->regulator_data[i].init_data;
+		d->constraints.valid_modes_mask |= LP872X_VALID_OPMODE;
+		d->constraints.valid_ops_mask |= REGULATOR_CHANGE_MODE;
+	}
+out:
+	return pdata;
+}
+#else
+static struct lp872x_platform_data
+*lp872x_populate_pdata_from_dt(struct device *dev, enum lp872x_id which)
+{
+	return NULL;
+}
+#endif
+
 static int lp872x_probe(struct i2c_client *cl, const struct i2c_device_id *id)
 {
 	struct lp872x *lp;
@@ -838,6 +938,10 @@ static int lp872x_probe(struct i2c_client *cl, const struct i2c_device_id *id)
 		[LP8725] = LP8725_NUM_REGULATORS,
 	};
 
+	if (cl->dev.of_node)
+		cl->dev.platform_data = lp872x_populate_pdata_from_dt(&cl->dev,
+					      (enum lp872x_id)id->driver_data);
+
 	lp = devm_kzalloc(&cl->dev, sizeof(struct lp872x), GFP_KERNEL);
 	if (!lp)
 		goto err_mem;
@@ -882,6 +986,13 @@ static int lp872x_remove(struct i2c_client *cl)
 	return 0;
 }
 
+static const struct of_device_id lp872x_dt_ids[] = {
+	{ .compatible = "ti,lp8720", },
+	{ .compatible = "ti,lp8725", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, lp872x_dt_ids);
+
 static const struct i2c_device_id lp872x_ids[] = {
 	{"lp8720", LP8720},
 	{"lp8725", LP8725},
@@ -893,6 +1004,7 @@ static struct i2c_driver lp872x_driver = {
 	.driver = {
 		.name = "lp872x",
 		.owner = THIS_MODULE,
+		.of_match_table = of_match_ptr(lp872x_dt_ids),
 	},
 	.probe = lp872x_probe,
 	.remove = lp872x_remove,

drivers/regulator/lp8755.c

@@ -19,7 +19,6 @@
 #include <linux/interrupt.h>
 #include <linux/gpio.h>
 #include <linux/regmap.h>
-#include <linux/delay.h>
 #include <linux/uaccess.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>

drivers/regulator/lp8788-buck.c

@@ -533,7 +533,6 @@ static int lp8788_buck_remove(struct platform_device *pdev)
 {
 	struct lp8788_buck *buck = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
 	regulator_unregister(buck->regulator);
 
 	return 0;

drivers/regulator/lp8788-ldo.c

@@ -561,7 +561,6 @@ static int lp8788_dldo_remove(struct platform_device *pdev)
 {
 	struct lp8788_ldo *ldo = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
 	regulator_unregister(ldo->regulator);
 
 	return 0;
@@ -622,7 +621,6 @@ static int lp8788_aldo_remove(struct platform_device *pdev)
 {
 	struct lp8788_ldo *ldo = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
 	regulator_unregister(ldo->regulator);
 
 	return 0;

drivers/regulator/max77686.c

@@ -24,7 +24,6 @@
 
 #include <linux/kernel.h>
 #include <linux/bug.h>
-#include <linux/delay.h>
 #include <linux/err.h>
 #include <linux/gpio.h>
 #include <linux/slab.h>

drivers/regulator/max77693.c

@@ -0,0 +1,322 @@
+/*
+ * max77693.c - Regulator driver for the Maxim 77693
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Jonghwa Lee <jonghwa3.lee@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ * This driver is based on max77686.c
+ */
+
+#include <linux/err.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/module.h>
+#include <linux/export.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/mfd/max77693.h>
+#include <linux/mfd/max77693-private.h>
+#include <linux/regulator/of_regulator.h>
+
+#define CHGIN_ILIM_STEP_20mA			20000
+
+struct max77693_pmic_dev {
+	struct device *dev;
+	struct max77693_dev *iodev;
+	int num_regulators;
+	struct regulator_dev **rdev;
+};
+
+/* CHARGER regulator ops */
+/* CHARGER regulator uses two bits for enabling */
+static int max77693_chg_is_enabled(struct regulator_dev *rdev)
+{
+	int ret;
+	u8 val;
+
+	ret = max77693_read_reg(rdev->regmap, rdev->desc->enable_reg, &val);
+	if (ret)
+		return ret;
+
+	return (val & rdev->desc->enable_mask) == rdev->desc->enable_mask;
+}
+
+/*
+ * CHARGER regulator - Min : 20mA, Max : 2580mA, step : 20mA
+ * 0x00, 0x01, 0x2, 0x03	= 60 mA
+ * 0x04 ~ 0x7E			= (60 + (X - 3) * 20) mA
+ */
+static int max77693_chg_get_current_limit(struct regulator_dev *rdev)
+{
+	unsigned int chg_min_uA = rdev->constraints->min_uA;
+	unsigned int chg_max_uA = rdev->constraints->max_uA;
+	u8 reg, sel;
+	unsigned int val;
+	int ret;
+
+	ret = max77693_read_reg(rdev->regmap,
+				MAX77693_CHG_REG_CHG_CNFG_09, &reg);
+	if (ret < 0)
+		return ret;
+
+	sel = reg & CHG_CNFG_09_CHGIN_ILIM_MASK;
+
+	/* the first four codes for charger current are all 60mA */
+	if (sel <= 3)
+		sel = 0;
+	else
+		sel -= 3;
+
+	val = chg_min_uA + CHGIN_ILIM_STEP_20mA * sel;
+	if (val > chg_max_uA)
+		return -EINVAL;
+
+	return val;
+}
+
+static int max77693_chg_set_current_limit(struct regulator_dev *rdev,
+						int min_uA, int max_uA)
+{
+	unsigned int chg_min_uA = rdev->constraints->min_uA;
+	int sel = 0;
+
+	while (chg_min_uA + CHGIN_ILIM_STEP_20mA * sel < min_uA)
+		sel++;
+
+	if (chg_min_uA + CHGIN_ILIM_STEP_20mA * sel > max_uA)
+		return -EINVAL;
+
+	/* the first four codes for charger current are all 60mA */
+	sel += 3;
+
+	return max77693_write_reg(rdev->regmap,
+				MAX77693_CHG_REG_CHG_CNFG_09, sel);
+}
+/* end of CHARGER regulator ops */
+
+static const unsigned int max77693_safeout_table[] = {
+	4850000,
+	4900000,
+	4950000,
+	3300000,
+};
+
+static struct regulator_ops max77693_safeout_ops = {
+	.list_voltage		= regulator_list_voltage_table,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+};
+
+static struct regulator_ops max77693_charger_ops = {
+	.is_enabled		= max77693_chg_is_enabled,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.get_current_limit	= max77693_chg_get_current_limit,
+	.set_current_limit	= max77693_chg_set_current_limit,
+};
+
+#define regulator_desc_esafeout(_num)	{			\
+	.name		= "ESAFEOUT"#_num,			\
+	.id		= MAX77693_ESAFEOUT##_num,		\
+	.n_voltages	= 4,					\
+	.ops		= &max77693_safeout_ops,		\
+	.type		= REGULATOR_VOLTAGE,			\
+	.volt_table	= max77693_safeout_table,		\
+	.vsel_reg	= MAX77693_CHG_REG_SAFEOUT_CTRL,	\
+	.vsel_mask	= SAFEOUT_CTRL_SAFEOUT##_num##_MASK,	\
+	.enable_reg	= MAX77693_CHG_REG_SAFEOUT_CTRL,	\
+	.enable_mask	= SAFEOUT_CTRL_ENSAFEOUT##_num##_MASK ,	\
+}
+
+static struct regulator_desc regulators[] = {
+	regulator_desc_esafeout(1),
+	regulator_desc_esafeout(2),
+	{
+		.name = "CHARGER",
+		.id = MAX77693_CHARGER,
+		.ops = &max77693_charger_ops,
+		.type = REGULATOR_CURRENT,
+		.owner = THIS_MODULE,
+		.enable_reg = MAX77693_CHG_REG_CHG_CNFG_00,
+		.enable_mask = CHG_CNFG_00_CHG_MASK |
+				CHG_CNFG_00_BUCK_MASK,
+	},
+};
+
+#ifdef CONFIG_OF
+static int max77693_pmic_dt_parse_rdata(struct device *dev,
+					struct max77693_regulator_data **rdata)
+{
+	struct device_node *np;
+	struct of_regulator_match *rmatch;
+	struct max77693_regulator_data *tmp;
+	int i, matched = 0;
+
+	np = of_find_node_by_name(dev->parent->of_node, "regulators");
+	if (!np)
+		return -EINVAL;
+
+	rmatch = devm_kzalloc(dev,
+		 sizeof(*rmatch) * ARRAY_SIZE(regulators), GFP_KERNEL);
+	if (!rmatch)
+		return -ENOMEM;
+
+	for (i = 0; i < ARRAY_SIZE(regulators); i++)
+		rmatch[i].name = regulators[i].name;
+
+	matched = of_regulator_match(dev, np, rmatch, ARRAY_SIZE(regulators));
+	if (matched <= 0)
+		return matched;
+	*rdata = devm_kzalloc(dev, sizeof(**rdata) * matched, GFP_KERNEL);
+	if (!(*rdata))
+		return -ENOMEM;
+
+	tmp = *rdata;
+
+	for (i = 0; i < matched; i++) {
+		tmp->initdata = rmatch[i].init_data;
+		tmp->of_node = rmatch[i].of_node;
+		tmp->id = regulators[i].id;
+		tmp++;
+	}
+
+	return matched;
+}
+#else
+static int max77693_pmic_dt_parse_rdata(struct device *dev,
+					struct max77693_regulator_data **rdata)
+{
+	return 0;
+}
+#endif /* CONFIG_OF */
+
+static int max77693_pmic_init_rdata(struct device *dev,
+				    struct max77693_regulator_data **rdata)
+{
+	struct max77693_platform_data *pdata;
+	int num_regulators = 0;
+
+	pdata = dev_get_platdata(dev->parent);
+	if (pdata) {
+		*rdata = pdata->regulators;
+		num_regulators = pdata->num_regulators;
+	}
+
+	if (!(*rdata) && dev->parent->of_node)
+		num_regulators = max77693_pmic_dt_parse_rdata(dev, rdata);
+
+	return num_regulators;
+}
+
+static int max77693_pmic_probe(struct platform_device *pdev)
+{
+	struct max77693_dev *iodev = dev_get_drvdata(pdev->dev.parent);
+	struct max77693_pmic_dev *max77693_pmic;
+	struct max77693_regulator_data *rdata = NULL;
+	int num_rdata, i, ret;
+	struct regulator_config config;
+
+	num_rdata = max77693_pmic_init_rdata(&pdev->dev, &rdata);
+	if (!rdata || num_rdata <= 0) {
+		dev_err(&pdev->dev, "No init data supplied.\n");
+		return -ENODEV;
+	}
+
+	max77693_pmic = devm_kzalloc(&pdev->dev,
+				sizeof(struct max77693_pmic_dev),
+				GFP_KERNEL);
+	if (!max77693_pmic)
+		return -ENOMEM;
+
+	max77693_pmic->rdev = devm_kzalloc(&pdev->dev,
+				sizeof(struct regulator_dev *) * num_rdata,
+				GFP_KERNEL);
+	if (!max77693_pmic->rdev)
+		return -ENOMEM;
+
+	max77693_pmic->dev = &pdev->dev;
+	max77693_pmic->iodev = iodev;
+	max77693_pmic->num_regulators = num_rdata;
+
+	config.dev = &pdev->dev;
+	config.regmap = iodev->regmap;
+	config.driver_data = max77693_pmic;
+	platform_set_drvdata(pdev, max77693_pmic);
+
+	for (i = 0; i < max77693_pmic->num_regulators; i++) {
+		int id = rdata[i].id;
+
+		config.init_data = rdata[i].initdata;
+		config.of_node = rdata[i].of_node;
+
+		max77693_pmic->rdev[i] = regulator_register(&regulators[id],
+							    &config);
+		if (IS_ERR(max77693_pmic->rdev[i])) {
+			ret = PTR_ERR(max77693_pmic->rdev[i]);
+			dev_err(max77693_pmic->dev,
+				"Failed to initialize regulator-%d\n", id);
+			max77693_pmic->rdev[i] = NULL;
+			goto err;
+		}
+	}
+
+	return 0;
+ err:
+	while (--i >= 0)
+		regulator_unregister(max77693_pmic->rdev[i]);
+
+	return ret;
+}
+
+static int max77693_pmic_remove(struct platform_device *pdev)
+{
+	struct max77693_pmic_dev *max77693_pmic = platform_get_drvdata(pdev);
+	struct regulator_dev **rdev = max77693_pmic->rdev;
+	int i;
+
+	for (i = 0; i < max77693_pmic->num_regulators; i++)
+		if (rdev[i])
+			regulator_unregister(rdev[i]);
+
+	return 0;
+}
+
+static const struct platform_device_id max77693_pmic_id[] = {
+	{"max77693-pmic", 0},
+	{},
+};
+
+MODULE_DEVICE_TABLE(platform, max77693_pmic_id);
+
+static struct platform_driver max77693_pmic_driver = {
+	.driver = {
+		   .name = "max77693-pmic",
+		   .owner = THIS_MODULE,
+		   },
+	.probe = max77693_pmic_probe,
+	.remove = max77693_pmic_remove,
+	.id_table = max77693_pmic_id,
+};
+
+module_platform_driver(max77693_pmic_driver);
+
+MODULE_DESCRIPTION("MAXIM MAX77693 regulator driver");
+MODULE_AUTHOR("Jonghwa Lee <jonghwa3.lee@samsung.com>");
+MODULE_LICENSE("GPL");

drivers/regulator/max8925-regulator.c

@@ -327,7 +327,6 @@ static int max8925_regulator_remove(struct platform_device *pdev)
 {
 	struct regulator_dev *rdev = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
 	regulator_unregister(rdev);
 
 	return 0;

drivers/regulator/max8973-regulator.c

@@ -26,10 +26,12 @@
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/err.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/max8973-regulator.h>
+#include <linux/regulator/of_regulator.h>
 #include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/slab.h>
@@ -100,6 +102,7 @@ struct max8973_chip {
 	int curr_vout_reg;
 	int curr_gpio_val;
 	bool valid_dvs_gpio;
+	struct regulator_ops ops;
 };
 
 /*
@@ -240,7 +243,7 @@ static unsigned int max8973_dcdc_get_mode(struct regulator_dev *rdev)
 		REGULATOR_MODE_FAST : REGULATOR_MODE_NORMAL;
 }
 
-static struct regulator_ops max8973_dcdc_ops = {
+static const struct regulator_ops max8973_dcdc_ops = {
 	.get_voltage_sel	= max8973_dcdc_get_voltage_sel,
 	.set_voltage_sel	= max8973_dcdc_set_voltage_sel,
 	.list_voltage		= regulator_list_voltage_linear,
@@ -369,7 +372,8 @@ static int max8973_probe(struct i2c_client *client,
 	int ret;
 
 	pdata = client->dev.platform_data;
-	if (!pdata) {
+
+	if (!pdata && !client->dev.of_node) {
 		dev_err(&client->dev, "No Platform data");
 		return -EIO;
 	}
@@ -388,30 +392,36 @@ static int max8973_probe(struct i2c_client *client,
 	}
 
 	i2c_set_clientdata(client, max);
+	max->ops = max8973_dcdc_ops;
 	max->dev = &client->dev;
 	max->desc.name = id->name;
 	max->desc.id = 0;
-	max->desc.ops = &max8973_dcdc_ops;
+	max->desc.ops = &max->ops;
 	max->desc.type = REGULATOR_VOLTAGE;
 	max->desc.owner = THIS_MODULE;
 	max->desc.min_uV = MAX8973_MIN_VOLATGE;
 	max->desc.uV_step = MAX8973_VOLATGE_STEP;
 	max->desc.n_voltages = MAX8973_BUCK_N_VOLTAGE;
 
-	if (!pdata->enable_ext_control) {
+	if (!pdata || !pdata->enable_ext_control) {
 		max->desc.enable_reg = MAX8973_VOUT;
 		max->desc.enable_mask = MAX8973_VOUT_ENABLE;
-		max8973_dcdc_ops.enable = regulator_enable_regmap;
+		max->ops.enable = regulator_enable_regmap;
-		max8973_dcdc_ops.disable = regulator_disable_regmap;
+		max->ops.disable = regulator_disable_regmap;
-		max8973_dcdc_ops.is_enabled = regulator_is_enabled_regmap;
+		max->ops.is_enabled = regulator_is_enabled_regmap;
+	}
+
+	if (pdata) {
+		max->dvs_gpio = pdata->dvs_gpio;
+		max->enable_external_control = pdata->enable_ext_control;
+		max->curr_gpio_val = pdata->dvs_def_state;
+		max->curr_vout_reg = MAX8973_VOUT + pdata->dvs_def_state;
+	} else {
+		max->dvs_gpio = -EINVAL;
+		max->curr_vout_reg = MAX8973_VOUT;
 	}
 
-	max->enable_external_control = pdata->enable_ext_control;
-	max->dvs_gpio = pdata->dvs_gpio;
-	max->curr_gpio_val = pdata->dvs_def_state;
-	max->curr_vout_reg = MAX8973_VOUT + pdata->dvs_def_state;
 	max->lru_index[0] = max->curr_vout_reg;
-	max->valid_dvs_gpio = false;
 
 	if (gpio_is_valid(max->dvs_gpio)) {
 		int gpio_flags;
@@ -437,16 +447,21 @@ static int max8973_probe(struct i2c_client *client,
 			max->lru_index[i] = i;
 		max->lru_index[0] = max->curr_vout_reg;
 		max->lru_index[max->curr_vout_reg] = 0;
+	} else {
+		max->valid_dvs_gpio = false;
 	}
 
-	ret = max8973_init_dcdc(max, pdata);
+	if (pdata) {
-	if (ret < 0) {
+		ret = max8973_init_dcdc(max, pdata);
-		dev_err(max->dev, "Max8973 Init failed, err = %d\n", ret);
+		if (ret < 0) {
-		return ret;
+			dev_err(max->dev, "Max8973 Init failed, err = %d\n", ret);
+			return ret;
+		}
 	}
 
 	config.dev = &client->dev;
-	config.init_data = pdata->reg_init_data;
+	config.init_data = pdata ? pdata->reg_init_data :
+		of_get_regulator_init_data(&client->dev, client->dev.of_node);
 	config.driver_data = max;
 	config.of_node = client->dev.of_node;
 	config.regmap = max->regmap;

drivers/regulator/mc13783-regulator.c

@@ -466,8 +466,6 @@ static int mc13783_regulator_remove(struct platform_device *pdev)
 	struct mc13xxx_regulator_priv *priv = platform_get_drvdata(pdev);
 	int i;
 
-	platform_set_drvdata(pdev, NULL);
-
 	for (i = 0; i < priv->num_regulators; i++)
 		regulator_unregister(priv->regulators[i]);
 

drivers/regulator/mc13892-regulator.c

@@ -636,8 +636,6 @@ static int mc13892_regulator_remove(struct platform_device *pdev)
 	struct mc13xxx_regulator_priv *priv = platform_get_drvdata(pdev);
 	int i;
 
-	platform_set_drvdata(pdev, NULL);
-
 	for (i = 0; i < priv->num_regulators; i++)
 		regulator_unregister(priv->regulators[i]);
 

drivers/regulator/of_regulator.c

@@ -61,6 +61,9 @@ static void of_get_regulation_constraints(struct device_node *np,
 	else /* status change should be possible if not always on. */
 		constraints->valid_ops_mask |= REGULATOR_CHANGE_STATUS;
 
+	if (of_property_read_bool(np, "regulator-allow-bypass"))
+		constraints->valid_ops_mask |= REGULATOR_CHANGE_BYPASS;
+
 	ramp_delay = of_get_property(np, "regulator-ramp-delay", NULL);
 	if (ramp_delay)
 		constraints->ramp_delay = be32_to_cpu(*ramp_delay);

drivers/regulator/pcap-regulator.c

@@ -260,7 +260,6 @@ static int pcap_regulator_remove(struct platform_device *pdev)
 	struct regulator_dev *rdev = platform_get_drvdata(pdev);
 
 	regulator_unregister(rdev);
-	platform_set_drvdata(pdev, NULL);
 
 	return 0;
 }

drivers/regulator/pcf50633-regulator.c

@@ -106,7 +106,6 @@ static int pcf50633_regulator_remove(struct platform_device *pdev)
 {
 	struct regulator_dev *rdev = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
 	regulator_unregister(rdev);
 
 	return 0;

drivers/regulator/s2mps11.c

@@ -12,7 +12,6 @@
  */
 
 #include <linux/bug.h>
-#include <linux/delay.h>
 #include <linux/err.h>
 #include <linux/gpio.h>
 #include <linux/slab.h>

drivers/regulator/ti-abb-regulator.c

@@ -0,0 +1,910 @@
+/*
+ * Texas Instruments SoC Adaptive Body Bias(ABB) Regulator
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ * Mike Turquette <mturquette@ti.com>
+ *
+ * Copyright (C) 2012-2013 Texas Instruments, Inc.
+ * Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
+ * Nishanth Menon <nm@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+
+/*
+ * ABB LDO operating states:
+ * NOMINAL_OPP:	bypasses the ABB LDO
+ * FAST_OPP:	sets ABB LDO to Forward Body-Bias
+ * SLOW_OPP:	sets ABB LDO to Reverse Body-Bias
+ */
+#define TI_ABB_NOMINAL_OPP	0
+#define TI_ABB_FAST_OPP		1
+#define TI_ABB_SLOW_OPP		3
+
+/**
+ * struct ti_abb_info - ABB information per voltage setting
+ * @opp_sel:	one of TI_ABB macro
+ * @vset:	(optional) vset value that LDOVBB needs to be overriden with.
+ *
+ * Array of per voltage entries organized in the same order as regulator_desc's
+ * volt_table list. (selector is used to index from this array)
+ */
+struct ti_abb_info {
+	u32 opp_sel;
+	u32 vset;
+};
+
+/**
+ * struct ti_abb_reg - Register description for ABB block
+ * @setup_reg:			setup register offset from base
+ * @control_reg:		control register offset from base
+ * @sr2_wtcnt_value_mask:	setup register- sr2_wtcnt_value mask
+ * @fbb_sel_mask:		setup register- FBB sel mask
+ * @rbb_sel_mask:		setup register- RBB sel mask
+ * @sr2_en_mask:		setup register- enable mask
+ * @opp_change_mask:		control register - mask to trigger LDOVBB change
+ * @opp_sel_mask:		control register - mask for mode to operate
+ */
+struct ti_abb_reg {
+	u32 setup_reg;
+	u32 control_reg;
+
+	/* Setup register fields */
+	u32 sr2_wtcnt_value_mask;
+	u32 fbb_sel_mask;
+	u32 rbb_sel_mask;
+	u32 sr2_en_mask;
+
+	/* Control register fields */
+	u32 opp_change_mask;
+	u32 opp_sel_mask;
+};
+
+/**
+ * struct ti_abb - ABB instance data
+ * @rdesc:			regulator descriptor
+ * @clk:			clock(usually sysclk) supplying ABB block
+ * @base:			base address of ABB block
+ * @int_base:			interrupt register base address
+ * @efuse_base:			(optional) efuse base address for ABB modes
+ * @ldo_base:			(optional) LDOVBB vset override base address
+ * @regs:			pointer to struct ti_abb_reg for ABB block
+ * @txdone_mask:		mask on int_base for tranxdone interrupt
+ * @ldovbb_override_mask:	mask to ldo_base for overriding default LDO VBB
+ *				vset with value from efuse
+ * @ldovbb_vset_mask:		mask to ldo_base for providing the VSET override
+ * @info:			array to per voltage ABB configuration
+ * @current_info_idx:		current index to info
+ * @settling_time:		SoC specific settling time for LDO VBB
+ */
+struct ti_abb {
+	struct regulator_desc rdesc;
+	struct clk *clk;
+	void __iomem *base;
+	void __iomem *int_base;
+	void __iomem *efuse_base;
+	void __iomem *ldo_base;
+
+	const struct ti_abb_reg *regs;
+	u32 txdone_mask;
+	u32 ldovbb_override_mask;
+	u32 ldovbb_vset_mask;
+
+	struct ti_abb_info *info;
+	int current_info_idx;
+
+	u32 settling_time;
+};
+
+/**
+ * ti_abb_rmw() - handy wrapper to set specific register bits
+ * @mask:	mask for register field
+ * @value:	value shifted to mask location and written
+ * @offset:	offset of register
+ * @base:	base address
+ *
+ * Return: final register value (may be unused)
+ */
+static inline u32 ti_abb_rmw(u32 mask, u32 value, u32 offset,
+			     void __iomem *base)
+{
+	u32 val;
+
+	val = readl(base + offset);
+	val &= ~mask;
+	val |= (value << __ffs(mask)) & mask;
+	writel(val, base + offset);
+
+	return val;
+}
+
+/**
+ * ti_abb_check_txdone() - handy wrapper to check ABB tranxdone status
+ * @abb:	pointer to the abb instance
+ *
+ * Return: true or false
+ */
+static inline bool ti_abb_check_txdone(const struct ti_abb *abb)
+{
+	return !!(readl(abb->int_base) & abb->txdone_mask);
+}
+
+/**
+ * ti_abb_clear_txdone() - handy wrapper to clear ABB tranxdone status
+ * @abb:	pointer to the abb instance
+ */
+static inline void ti_abb_clear_txdone(const struct ti_abb *abb)
+{
+	writel(abb->txdone_mask, abb->int_base);
+};
+
+/**
+ * ti_abb_wait_tranx() - waits for ABB tranxdone event
+ * @dev:	device
+ * @abb:	pointer to the abb instance
+ *
+ * Return: 0 on success or -ETIMEDOUT if the event is not cleared on time.
+ */
+static int ti_abb_wait_txdone(struct device *dev, struct ti_abb *abb)
+{
+	int timeout = 0;
+	bool status;
+
+	while (timeout++ <= abb->settling_time) {
+		status = ti_abb_check_txdone(abb);
+		if (status)
+			break;
+
+		udelay(1);
+	}
+
+	if (timeout > abb->settling_time) {
+		dev_warn_ratelimited(dev,
+				     "%s:TRANXDONE timeout(%duS) int=0x%08x\n",
+				     __func__, timeout, readl(abb->int_base));
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+/**
+ * ti_abb_clear_all_txdone() - clears ABB tranxdone event
+ * @dev:	device
+ * @abb:	pointer to the abb instance
+ *
+ * Return: 0 on success or -ETIMEDOUT if the event is not cleared on time.
+ */
+static int ti_abb_clear_all_txdone(struct device *dev, const struct ti_abb *abb)
+{
+	int timeout = 0;
+	bool status;
+
+	while (timeout++ <= abb->settling_time) {
+		ti_abb_clear_txdone(abb);
+
+		status = ti_abb_check_txdone(abb);
+		if (!status)
+			break;
+
+		udelay(1);
+	}
+
+	if (timeout > abb->settling_time) {
+		dev_warn_ratelimited(dev,
+				     "%s:TRANXDONE timeout(%duS) int=0x%08x\n",
+				     __func__, timeout, readl(abb->int_base));
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+/**
+ * ti_abb_program_ldovbb() - program LDOVBB register for override value
+ * @dev:	device
+ * @abb:	pointer to the abb instance
+ * @info:	ABB info to program
+ */
+static void ti_abb_program_ldovbb(struct device *dev, const struct ti_abb *abb,
+				  struct ti_abb_info *info)
+{
+	u32 val;
+
+	val = readl(abb->ldo_base);
+	/* clear up previous values */
+	val &= ~(abb->ldovbb_override_mask | abb->ldovbb_vset_mask);
+
+	switch (info->opp_sel) {
+	case TI_ABB_SLOW_OPP:
+	case TI_ABB_FAST_OPP:
+		val |= abb->ldovbb_override_mask;
+		val |= info->vset << __ffs(abb->ldovbb_vset_mask);
+		break;
+	}
+
+	writel(val, abb->ldo_base);
+}
+
+/**
+ * ti_abb_set_opp() - Setup ABB and LDO VBB for required bias
+ * @rdev:	regulator device
+ * @abb:	pointer to the abb instance
+ * @info:	ABB info to program
+ *
+ * Return: 0 on success or appropriate error value when fails
+ */
+static int ti_abb_set_opp(struct regulator_dev *rdev, struct ti_abb *abb,
+			  struct ti_abb_info *info)
+{
+	const struct ti_abb_reg *regs = abb->regs;
+	struct device *dev = &rdev->dev;
+	int ret;
+
+	ret = ti_abb_clear_all_txdone(dev, abb);
+	if (ret)
+		goto out;
+
+	ti_abb_rmw(regs->fbb_sel_mask | regs->rbb_sel_mask, 0, regs->setup_reg,
+		   abb->base);
+
+	switch (info->opp_sel) {
+	case TI_ABB_SLOW_OPP:
+		ti_abb_rmw(regs->rbb_sel_mask, 1, regs->setup_reg, abb->base);
+		break;
+	case TI_ABB_FAST_OPP:
+		ti_abb_rmw(regs->fbb_sel_mask, 1, regs->setup_reg, abb->base);
+		break;
+	}
+
+	/* program next state of ABB ldo */
+	ti_abb_rmw(regs->opp_sel_mask, info->opp_sel, regs->control_reg,
+		   abb->base);
+
+	/* program LDO VBB vset override if needed */
+	if (abb->ldo_base)
+		ti_abb_program_ldovbb(dev, abb, info);
+
+	/* Initiate ABB ldo change */
+	ti_abb_rmw(regs->opp_change_mask, 1, regs->control_reg, abb->base);
+
+	/* Wait for ABB LDO to complete transition to new Bias setting */
+	ret = ti_abb_wait_txdone(dev, abb);
+	if (ret)
+		goto out;
+
+	ret = ti_abb_clear_all_txdone(dev, abb);
+	if (ret)
+		goto out;
+
+out:
+	return ret;
+}
+
+/**
+ * ti_abb_set_voltage_sel() - regulator accessor function to set ABB LDO
+ * @rdev:	regulator device
+ * @sel:	selector to index into required ABB LDO settings (maps to
+ *		regulator descriptor's volt_table)
+ *
+ * Return: 0 on success or appropriate error value when fails
+ */
+static int ti_abb_set_voltage_sel(struct regulator_dev *rdev, unsigned sel)
+{
+	const struct regulator_desc *desc = rdev->desc;
+	struct ti_abb *abb = rdev_get_drvdata(rdev);
+	struct device *dev = &rdev->dev;
+	struct ti_abb_info *info, *oinfo;
+	int ret = 0;
+
+	if (!abb) {
+		dev_err_ratelimited(dev, "%s: No regulator drvdata\n",
+				    __func__);
+		return -ENODEV;
+	}
+
+	if (!desc->n_voltages || !abb->info) {
+		dev_err_ratelimited(dev,
+				    "%s: No valid voltage table entries?\n",
+				    __func__);
+		return -EINVAL;
+	}
+
+	if (sel >= desc->n_voltages) {
+		dev_err(dev, "%s: sel idx(%d) >= n_voltages(%d)\n", __func__,
+			sel, desc->n_voltages);
+		return -EINVAL;
+	}
+
+	/* If we are in the same index as we were, nothing to do here! */
+	if (sel == abb->current_info_idx) {
+		dev_dbg(dev, "%s: Already at sel=%d\n", __func__, sel);
+		return ret;
+	}
+
+	/* If data is exactly the same, then just update index, no change */
+	info = &abb->info[sel];
+	oinfo = &abb->info[abb->current_info_idx];
+	if (!memcmp(info, oinfo, sizeof(*info))) {
+		dev_dbg(dev, "%s: Same data new idx=%d, old idx=%d\n", __func__,
+			sel, abb->current_info_idx);
+		goto out;
+	}
+
+	ret = ti_abb_set_opp(rdev, abb, info);
+
+out:
+	if (!ret)
+		abb->current_info_idx = sel;
+	else
+		dev_err_ratelimited(dev,
+				    "%s: Volt[%d] idx[%d] mode[%d] Fail(%d)\n",
+				    __func__, desc->volt_table[sel], sel,
+				    info->opp_sel, ret);
+	return ret;
+}
+
+/**
+ * ti_abb_get_voltage_sel() - Regulator accessor to get current ABB LDO setting
+ * @rdev:	regulator device
+ *
+ * Return: 0 on success or appropriate error value when fails
+ */
+static int ti_abb_get_voltage_sel(struct regulator_dev *rdev)
+{
+	const struct regulator_desc *desc = rdev->desc;
+	struct ti_abb *abb = rdev_get_drvdata(rdev);
+	struct device *dev = &rdev->dev;
+
+	if (!abb) {
+		dev_err_ratelimited(dev, "%s: No regulator drvdata\n",
+				    __func__);
+		return -ENODEV;
+	}
+
+	if (!desc->n_voltages || !abb->info) {
+		dev_err_ratelimited(dev,
+				    "%s: No valid voltage table entries?\n",
+				    __func__);
+		return -EINVAL;
+	}
+
+	if (abb->current_info_idx >= (int)desc->n_voltages) {
+		dev_err(dev, "%s: Corrupted data? idx(%d) >= n_voltages(%d)\n",
+			__func__, abb->current_info_idx, desc->n_voltages);
+		return -EINVAL;
+	}
+
+	return abb->current_info_idx;
+}
+
+/**
+ * ti_abb_init_timings() - setup ABB clock timing for the current platform
+ * @dev:	device
+ * @abb:	pointer to the abb instance
+ *
+ * Return: 0 if timing is updated, else returns error result.
+ */
+static int ti_abb_init_timings(struct device *dev, struct ti_abb *abb)
+{
+	u32 clock_cycles;
+	u32 clk_rate, sr2_wt_cnt_val, cycle_rate;
+	const struct ti_abb_reg *regs = abb->regs;
+	int ret;
+	char *pname = "ti,settling-time";
+
+	/* read device tree properties */
+	ret = of_property_read_u32(dev->of_node, pname, &abb->settling_time);
+	if (ret) {
+		dev_err(dev, "Unable to get property '%s'(%d)\n", pname, ret);
+		return ret;
+	}
+
+	/* ABB LDO cannot be settle in 0 time */
+	if (!abb->settling_time) {
+		dev_err(dev, "Invalid property:'%s' set as 0!\n", pname);
+		return -EINVAL;
+	}
+
+	pname = "ti,clock-cycles";
+	ret = of_property_read_u32(dev->of_node, pname, &clock_cycles);
+	if (ret) {
+		dev_err(dev, "Unable to get property '%s'(%d)\n", pname, ret);
+		return ret;
+	}
+	/* ABB LDO cannot be settle in 0 clock cycles */
+	if (!clock_cycles) {
+		dev_err(dev, "Invalid property:'%s' set as 0!\n", pname);
+		return -EINVAL;
+	}
+
+	abb->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(abb->clk)) {
+		ret = PTR_ERR(abb->clk);
+		dev_err(dev, "%s: Unable to get clk(%d)\n", __func__, ret);
+		return ret;
+	}
+
+	/*
+	 * SR2_WTCNT_VALUE is the settling time for the ABB ldo after a
+	 * transition and must be programmed with the correct time at boot.
+	 * The value programmed into the register is the number of SYS_CLK
+	 * clock cycles that match a given wall time profiled for the ldo.
+	 * This value depends on:
+	 * settling time of ldo in micro-seconds (varies per OMAP family)
+	 * # of clock cycles per SYS_CLK period (varies per OMAP family)
+	 * the SYS_CLK frequency in MHz (varies per board)
+	 * The formula is:
+	 *
+	 *                      ldo settling time (in micro-seconds)
+	 * SR2_WTCNT_VALUE = ------------------------------------------
+	 *                   (# system clock cycles) * (sys_clk period)
+	 *
+	 * Put another way:
+	 *
+	 * SR2_WTCNT_VALUE = settling time / (# SYS_CLK cycles / SYS_CLK rate))
+	 *
+	 * To avoid dividing by zero multiply both "# clock cycles" and
+	 * "settling time" by 10 such that the final result is the one we want.
+	 */
+
+	/* Convert SYS_CLK rate to MHz & prevent divide by zero */
+	clk_rate = DIV_ROUND_CLOSEST(clk_get_rate(abb->clk), 1000000);
+
+	/* Calculate cycle rate */
+	cycle_rate = DIV_ROUND_CLOSEST(clock_cycles * 10, clk_rate);
+
+	/* Calulate SR2_WTCNT_VALUE */
+	sr2_wt_cnt_val = DIV_ROUND_CLOSEST(abb->settling_time * 10, cycle_rate);
+
+	dev_dbg(dev, "%s: Clk_rate=%ld, sr2_cnt=0x%08x\n", __func__,
+		clk_get_rate(abb->clk), sr2_wt_cnt_val);
+
+	ti_abb_rmw(regs->sr2_wtcnt_value_mask, sr2_wt_cnt_val, regs->setup_reg,
+		   abb->base);
+
+	return 0;
+}
+
+/**
+ * ti_abb_init_table() - Initialize ABB table from device tree
+ * @dev:	device
+ * @abb:	pointer to the abb instance
+ * @rinit_data:	regulator initdata
+ *
+ * Return: 0 on success or appropriate error value when fails
+ */
+static int ti_abb_init_table(struct device *dev, struct ti_abb *abb,
+			     struct regulator_init_data *rinit_data)
+{
+	struct ti_abb_info *info;
+	const struct property *prop;
+	const __be32 *abb_info;
+	const u32 num_values = 6;
+	char *pname = "ti,abb_info";
+	u32 num_entries, i;
+	unsigned int *volt_table;
+	int min_uV = INT_MAX, max_uV = 0;
+	struct regulation_constraints *c = &rinit_data->constraints;
+
+	prop = of_find_property(dev->of_node, pname, NULL);
+	if (!prop) {
+		dev_err(dev, "No '%s' property?\n", pname);
+		return -ENODEV;
+	}
+
+	if (!prop->value) {
+		dev_err(dev, "Empty '%s' property?\n", pname);
+		return -ENODATA;
+	}
+
+	/*
+	 * Each abb_info is a set of n-tuple, where n is num_values, consisting
+	 * of voltage and a set of detection logic for ABB information for that
+	 * voltage to apply.
+	 */
+	num_entries = prop->length / sizeof(u32);
+	if (!num_entries || (num_entries % num_values)) {
+		dev_err(dev, "All '%s' list entries need %d vals\n", pname,
+			num_values);
+		return -EINVAL;
+	}
+	num_entries /= num_values;
+
+	info = devm_kzalloc(dev, sizeof(*info) * num_entries, GFP_KERNEL);
+	if (!info) {
+		dev_err(dev, "Can't allocate info table for '%s' property\n",
+			pname);
+		return -ENOMEM;
+	}
+	abb->info = info;
+
+	volt_table = devm_kzalloc(dev, sizeof(unsigned int) * num_entries,
+				  GFP_KERNEL);
+	if (!volt_table) {
+		dev_err(dev, "Can't allocate voltage table for '%s' property\n",
+			pname);
+		return -ENOMEM;
+	}
+
+	abb->rdesc.n_voltages = num_entries;
+	abb->rdesc.volt_table = volt_table;
+	/* We do not know where the OPP voltage is at the moment */
+	abb->current_info_idx = -EINVAL;
+
+	abb_info = prop->value;
+	for (i = 0; i < num_entries; i++, info++, volt_table++) {
+		u32 efuse_offset, rbb_mask, fbb_mask, vset_mask;
+		u32 efuse_val;
+
+		/* NOTE: num_values should equal to entries picked up here */
+		*volt_table = be32_to_cpup(abb_info++);
+		info->opp_sel = be32_to_cpup(abb_info++);
+		efuse_offset = be32_to_cpup(abb_info++);
+		rbb_mask = be32_to_cpup(abb_info++);
+		fbb_mask = be32_to_cpup(abb_info++);
+		vset_mask = be32_to_cpup(abb_info++);
+
+		dev_dbg(dev,
+			"[%d]v=%d ABB=%d ef=0x%x rbb=0x%x fbb=0x%x vset=0x%x\n",
+			i, *volt_table, info->opp_sel, efuse_offset, rbb_mask,
+			fbb_mask, vset_mask);
+
+		/* Find min/max for voltage set */
+		if (min_uV > *volt_table)
+			min_uV = *volt_table;
+		if (max_uV < *volt_table)
+			max_uV = *volt_table;
+
+		if (!abb->efuse_base) {
+			/* Ignore invalid data, but warn to help cleanup */
+			if (efuse_offset || rbb_mask || fbb_mask || vset_mask)
+				dev_err(dev, "prop '%s': v=%d,bad efuse/mask\n",
+					pname, *volt_table);
+			goto check_abb;
+		}
+
+		efuse_val = readl(abb->efuse_base + efuse_offset);
+
+		/* Use ABB recommendation from Efuse */
+		if (efuse_val & rbb_mask)
+			info->opp_sel = TI_ABB_SLOW_OPP;
+		else if (efuse_val & fbb_mask)
+			info->opp_sel = TI_ABB_FAST_OPP;
+		else if (rbb_mask || fbb_mask)
+			info->opp_sel = TI_ABB_NOMINAL_OPP;
+
+		dev_dbg(dev,
+			"[%d]v=%d efusev=0x%x final ABB=%d\n",
+			i, *volt_table, efuse_val, info->opp_sel);
+
+		/* Use recommended Vset bits from Efuse */
+		if (!abb->ldo_base) {
+			if (vset_mask)
+				dev_err(dev, "prop'%s':v=%d vst=%x LDO base?\n",
+					pname, *volt_table, vset_mask);
+			continue;
+		}
+		info->vset = efuse_val & vset_mask >> __ffs(vset_mask);
+		dev_dbg(dev, "[%d]v=%d vset=%x\n", i, *volt_table, info->vset);
+check_abb:
+		switch (info->opp_sel) {
+		case TI_ABB_NOMINAL_OPP:
+		case TI_ABB_FAST_OPP:
+		case TI_ABB_SLOW_OPP:
+			/* Valid values */
+			break;
+		default:
+			dev_err(dev, "%s:[%d]v=%d, ABB=%d is invalid! Abort!\n",
+				__func__, i, *volt_table, info->opp_sel);
+			return -EINVAL;
+		}
+	}
+
+	/* Setup the min/max voltage constraints from the supported list */
+	c->min_uV = min_uV;
+	c->max_uV = max_uV;
+
+	return 0;
+}
+
+static struct regulator_ops ti_abb_reg_ops = {
+	.list_voltage = regulator_list_voltage_table,
+
+	.set_voltage_sel = ti_abb_set_voltage_sel,
+	.get_voltage_sel = ti_abb_get_voltage_sel,
+};
+
+/* Default ABB block offsets, IF this changes in future, create new one */
+static const struct ti_abb_reg abb_regs_v1 = {
+	/* WARNING: registers are wrongly documented in TRM */
+	.setup_reg		= 0x04,
+	.control_reg		= 0x00,
+
+	.sr2_wtcnt_value_mask	= (0xff << 8),
+	.fbb_sel_mask		= (0x01 << 2),
+	.rbb_sel_mask		= (0x01 << 1),
+	.sr2_en_mask		= (0x01 << 0),
+
+	.opp_change_mask	= (0x01 << 2),
+	.opp_sel_mask		= (0x03 << 0),
+};
+
+static const struct ti_abb_reg abb_regs_v2 = {
+	.setup_reg		= 0x00,
+	.control_reg		= 0x04,
+
+	.sr2_wtcnt_value_mask	= (0xff << 8),
+	.fbb_sel_mask		= (0x01 << 2),
+	.rbb_sel_mask		= (0x01 << 1),
+	.sr2_en_mask		= (0x01 << 0),
+
+	.opp_change_mask	= (0x01 << 2),
+	.opp_sel_mask		= (0x03 << 0),
+};
+
+static const struct of_device_id ti_abb_of_match[] = {
+	{.compatible = "ti,abb-v1", .data = &abb_regs_v1},
+	{.compatible = "ti,abb-v2", .data = &abb_regs_v2},
+	{ },
+};
+
+MODULE_DEVICE_TABLE(of, ti_abb_of_match);
+
+/**
+ * ti_abb_probe() - Initialize an ABB ldo instance
+ * @pdev: ABB platform device
+ *
+ * Initializes an individual ABB LDO for required Body-Bias. ABB is used to
+ * addional bias supply to SoC modules for power savings or mandatory stability
+ * configuration at certain Operating Performance Points(OPPs).
+ *
+ * Return: 0 on success or appropriate error value when fails
+ */
+static int ti_abb_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct of_device_id *match;
+	struct resource *res;
+	struct ti_abb *abb;
+	struct regulator_init_data *initdata = NULL;
+	struct regulator_dev *rdev = NULL;
+	struct regulator_desc *desc;
+	struct regulation_constraints *c;
+	struct regulator_config config = { };
+	char *pname;
+	int ret = 0;
+
+	match = of_match_device(ti_abb_of_match, dev);
+	if (!match) {
+		/* We do not expect this to happen */
+		ret = -ENODEV;
+		dev_err(dev, "%s: Unable to match device\n", __func__);
+		goto err;
+	}
+	if (!match->data) {
+		ret = -EINVAL;
+		dev_err(dev, "%s: Bad data in match\n", __func__);
+		goto err;
+	}
+
+	abb = devm_kzalloc(dev, sizeof(struct ti_abb), GFP_KERNEL);
+	if (!abb) {
+		dev_err(dev, "%s: Unable to allocate ABB struct\n", __func__);
+		ret = -ENOMEM;
+		goto err;
+	}
+	abb->regs = match->data;
+
+	/* Map ABB resources */
+	pname = "base-address";
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
+	if (!res) {
+		dev_err(dev, "Missing '%s' IO resource\n", pname);
+		ret = -ENODEV;
+		goto err;
+	}
+	abb->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(abb->base)) {
+		ret = PTR_ERR(abb->base);
+		goto err;
+	}
+
+	pname = "int-address";
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
+	if (!res) {
+		dev_err(dev, "Missing '%s' IO resource\n", pname);
+		ret = -ENODEV;
+		goto err;
+	}
+	/*
+	 * We may have shared interrupt register offsets which are
+	 * write-1-to-clear between domains ensuring exclusivity.
+	 */
+	abb->int_base = devm_ioremap_nocache(dev, res->start,
+					     resource_size(res));
+	if (!abb->int_base) {
+		dev_err(dev, "Unable to map '%s'\n", pname);
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	/* Map Optional resources */
+	pname = "efuse-address";
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
+	if (!res) {
+		dev_dbg(dev, "Missing '%s' IO resource\n", pname);
+		ret = -ENODEV;
+		goto skip_opt;
+	}
+
+	/*
+	 * We may have shared efuse register offsets which are read-only
+	 * between domains
+	 */
+	abb->efuse_base = devm_ioremap_nocache(dev, res->start,
+					       resource_size(res));
+	if (!abb->efuse_base) {
+		dev_err(dev, "Unable to map '%s'\n", pname);
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	pname = "ldo-address";
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
+	if (!res) {
+		dev_dbg(dev, "Missing '%s' IO resource\n", pname);
+		ret = -ENODEV;
+		goto skip_opt;
+	}
+	abb->ldo_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(abb->ldo_base)) {
+		ret = PTR_ERR(abb->ldo_base);
+		goto err;
+	}
+
+	/* IF ldo_base is set, the following are mandatory */
+	pname = "ti,ldovbb-override-mask";
+	ret =
+	    of_property_read_u32(pdev->dev.of_node, pname,
+				 &abb->ldovbb_override_mask);
+	if (ret) {
+		dev_err(dev, "Missing '%s' (%d)\n", pname, ret);
+		goto err;
+	}
+	if (!abb->ldovbb_override_mask) {
+		dev_err(dev, "Invalid property:'%s' set as 0!\n", pname);
+		ret = -EINVAL;
+		goto err;
+	}
+
+	pname = "ti,ldovbb-vset-mask";
+	ret =
+	    of_property_read_u32(pdev->dev.of_node, pname,
+				 &abb->ldovbb_vset_mask);
+	if (ret) {
+		dev_err(dev, "Missing '%s' (%d)\n", pname, ret);
+		goto err;
+	}
+	if (!abb->ldovbb_vset_mask) {
+		dev_err(dev, "Invalid property:'%s' set as 0!\n", pname);
+		ret = -EINVAL;
+		goto err;
+	}
+
+skip_opt:
+	pname = "ti,tranxdone-status-mask";
+	ret =
+	    of_property_read_u32(pdev->dev.of_node, pname,
+				 &abb->txdone_mask);
+	if (ret) {
+		dev_err(dev, "Missing '%s' (%d)\n", pname, ret);
+		goto err;
+	}
+	if (!abb->txdone_mask) {
+		dev_err(dev, "Invalid property:'%s' set as 0!\n", pname);
+		ret = -EINVAL;
+		goto err;
+	}
+
+	initdata = of_get_regulator_init_data(dev, pdev->dev.of_node);
+	if (!initdata) {
+		ret = -ENOMEM;
+		dev_err(dev, "%s: Unable to alloc regulator init data\n",
+			__func__);
+		goto err;
+	}
+
+	/* init ABB opp_sel table */
+	ret = ti_abb_init_table(dev, abb, initdata);
+	if (ret)
+		goto err;
+
+	/* init ABB timing */
+	ret = ti_abb_init_timings(dev, abb);
+	if (ret)
+		goto err;
+
+	desc = &abb->rdesc;
+	desc->name = dev_name(dev);
+	desc->owner = THIS_MODULE;
+	desc->type = REGULATOR_VOLTAGE;
+	desc->ops = &ti_abb_reg_ops;
+
+	c = &initdata->constraints;
+	if (desc->n_voltages > 1)
+		c->valid_ops_mask |= REGULATOR_CHANGE_VOLTAGE;
+	c->always_on = true;
+
+	config.dev = dev;
+	config.init_data = initdata;
+	config.driver_data = abb;
+	config.of_node = pdev->dev.of_node;
+
+	rdev = regulator_register(desc, &config);
+	if (IS_ERR(rdev)) {
+		ret = PTR_ERR(rdev);
+		dev_err(dev, "%s: failed to register regulator(%d)\n",
+			__func__, ret);
+		goto err;
+	}
+	platform_set_drvdata(pdev, rdev);
+
+	/* Enable the ldo if not already done by bootloader */
+	ti_abb_rmw(abb->regs->sr2_en_mask, 1, abb->regs->setup_reg, abb->base);
+
+	return 0;
+
+err:
+	dev_err(dev, "%s: Failed to initialize(%d)\n", __func__, ret);
+	return ret;
+}
+
+/**
+ * ti_abb_remove() - cleanups
+ * @pdev: ABB platform device
+ *
+ * Return: 0
+ */
+static int ti_abb_remove(struct platform_device *pdev)
+{
+	struct regulator_dev *rdev = platform_get_drvdata(pdev);
+
+	regulator_unregister(rdev);
+	return 0;
+}
+
+MODULE_ALIAS("platform:ti_abb");
+
+static struct platform_driver ti_abb_driver = {
+	.probe = ti_abb_probe,
+	.remove = ti_abb_remove,
+	.driver = {
+		   .name = "ti_abb",
+		   .owner = THIS_MODULE,
+		   .of_match_table = of_match_ptr(ti_abb_of_match),
+		   },
+};
+module_platform_driver(ti_abb_driver);
+
+MODULE_DESCRIPTION("Texas Instruments ABB LDO regulator driver");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_LICENSE("GPL v2");

drivers/regulator/tps62360-regulator.c

@@ -351,7 +351,6 @@ static int tps62360_probe(struct i2c_client *client,
 	int chip_id;
 
 	pdata = client->dev.platform_data;
-	chip_id = id->driver_data;
 
 	if (client->dev.of_node) {
 		const struct of_device_id *match;
@@ -364,6 +363,11 @@ static int tps62360_probe(struct i2c_client *client,
 		chip_id = (int)match->data;
 		if (!pdata)
 			pdata = of_get_tps62360_platform_data(&client->dev);
+	} else if (id) {
+		chip_id = id->driver_data;
+	} else {
+		dev_err(&client->dev, "No device tree match or id table match found\n");
+		return -ENODEV;
 	}
 
 	if (!pdata) {
@@ -402,7 +406,7 @@ static int tps62360_probe(struct i2c_client *client,
 		return -ENODEV;
 	}
 
-	tps->desc.name = id->name;
+	tps->desc.name = client->name;
 	tps->desc.id = 0;
 	tps->desc.ops = &tps62360_dcdc_ops;
 	tps->desc.type = REGULATOR_VOLTAGE;

drivers/regulator/tps65217-regulator.c

@@ -405,8 +405,6 @@ static int tps65217_regulator_remove(struct platform_device *pdev)
 	for (i = 0; i < TPS65217_NUM_REGULATOR; i++)
 		regulator_unregister(tps->rdev[i]);
 
-	platform_set_drvdata(pdev, NULL);
-
 	return 0;
 }
 

drivers/regulator/virtual.c

@@ -330,8 +330,6 @@ static int regulator_virtual_remove(struct platform_device *pdev)
 	if (drvdata->enabled)
 		regulator_disable(drvdata->regulator);
 
-	platform_set_drvdata(pdev, NULL);
-
 	return 0;
 }
 

drivers/regulator/wm831x-dcdc.c

@@ -567,8 +567,6 @@ static int wm831x_buckv_remove(struct platform_device *pdev)
 	struct wm831x_dcdc *dcdc = platform_get_drvdata(pdev);
 	struct wm831x *wm831x = dcdc->wm831x;
 
-	platform_set_drvdata(pdev, NULL);
-
 	free_irq(wm831x_irq(wm831x, platform_get_irq_byname(pdev, "HC")),
 			    dcdc);
 	free_irq(wm831x_irq(wm831x, platform_get_irq_byname(pdev, "UV")),
@@ -714,8 +712,6 @@ static int wm831x_buckp_remove(struct platform_device *pdev)
 {
 	struct wm831x_dcdc *dcdc = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
-
 	free_irq(wm831x_irq(dcdc->wm831x, platform_get_irq_byname(pdev, "UV")),
 			    dcdc);
 	regulator_unregister(dcdc->regulator);
@@ -849,8 +845,6 @@ static int wm831x_boostp_remove(struct platform_device *pdev)
 {
 	struct wm831x_dcdc *dcdc = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
-
 	free_irq(wm831x_irq(dcdc->wm831x, platform_get_irq_byname(pdev, "UV")),
 		 dcdc);
 	regulator_unregister(dcdc->regulator);
@@ -940,7 +934,6 @@ static int wm831x_epe_remove(struct platform_device *pdev)
 {
 	struct wm831x_dcdc *dcdc = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
 	regulator_unregister(dcdc->regulator);
 
 	return 0;

drivers/regulator/wm831x-isink.c

@@ -225,8 +225,6 @@ static int wm831x_isink_remove(struct platform_device *pdev)
 {
 	struct wm831x_isink *isink = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
-
 	free_irq(wm831x_irq(isink->wm831x, platform_get_irq(pdev, 0)), isink);
 
 	regulator_unregister(isink->regulator);

drivers/regulator/wm831x-ldo.c

@@ -338,8 +338,6 @@ static int wm831x_gp_ldo_remove(struct platform_device *pdev)
 {
 	struct wm831x_ldo *ldo = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
-
 	free_irq(wm831x_irq(ldo->wm831x,
 			    platform_get_irq_byname(pdev, "UV")), ldo);
 	regulator_unregister(ldo->regulator);

drivers/regulator/wm8400-regulator.c

@@ -250,7 +250,6 @@ static int wm8400_regulator_remove(struct platform_device *pdev)
 {
 	struct regulator_dev *rdev = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
 	regulator_unregister(rdev);
 
 	return 0;

drivers/regulator/wm8994-regulator.c

@@ -185,8 +185,6 @@ static int wm8994_ldo_remove(struct platform_device *pdev)
 {
 	struct wm8994_ldo *ldo = platform_get_drvdata(pdev);
 
-	platform_set_drvdata(pdev, NULL);
-
 	regulator_unregister(ldo->regulator);
 
 	return 0;

include/linux/mfd/max77693-private.h

@@ -85,6 +85,19 @@ enum max77693_pmic_reg {
 	MAX77693_PMIC_REG_END,
 };
 
+/* MAX77693 CHG_CNFG_00 register */
+#define CHG_CNFG_00_CHG_MASK		0x1
+#define CHG_CNFG_00_BUCK_MASK		0x4
+
+/* MAX77693 CHG_CNFG_09 Register */
+#define CHG_CNFG_09_CHGIN_ILIM_MASK	0x7F
+
+/* MAX77693 CHG_CTRL Register */
+#define SAFEOUT_CTRL_SAFEOUT1_MASK	0x3
+#define SAFEOUT_CTRL_SAFEOUT2_MASK	0xC
+#define SAFEOUT_CTRL_ENSAFEOUT1_MASK	0x40
+#define SAFEOUT_CTRL_ENSAFEOUT2_MASK	0x80
+
 /* Slave addr = 0x4A: MUIC */
 enum max77693_muic_reg {
 	MAX77693_MUIC_REG_ID		= 0x00,

include/linux/mfd/max77693.h

@@ -30,6 +30,20 @@
 #ifndef __LINUX_MFD_MAX77693_H
 #define __LINUX_MFD_MAX77693_H
 
+/* MAX77686 regulator IDs */
+enum max77693_regulators {
+	MAX77693_ESAFEOUT1 = 0,
+	MAX77693_ESAFEOUT2,
+	MAX77693_CHARGER,
+	MAX77693_REG_MAX,
+};
+
+struct max77693_regulator_data {
+	int id;
+	struct regulator_init_data *initdata;
+	struct device_node *of_node;
+};
+
 struct max77693_reg_data {
 	u8 addr;
 	u8 data;
@@ -52,6 +66,10 @@ struct max77693_muic_platform_data {
 struct max77693_platform_data {
 	int wakeup;
 
+	/* regulator data */
+	struct max77693_regulator_data *regulators;
+	int num_regulators;
+
 	/* muic data */
 	struct max77693_muic_platform_data *muic_data;
 };

include/linux/regulator/ab8500.h

@@ -336,8 +336,4 @@ static inline int ab8500_regulator_debug_exit(struct platform_device *pdev)
 }
 #endif
 
-/* AB8500 external regulator functions. */
-int ab8500_ext_regulator_init(struct platform_device *pdev);
-void ab8500_ext_regulator_exit(struct platform_device *pdev);
-
 #endif

include/linux/regulator/consumer.h

@@ -165,6 +165,7 @@ int regulator_count_voltages(struct regulator *regulator);
 int regulator_list_voltage(struct regulator *regulator, unsigned selector);
 int regulator_is_supported_voltage(struct regulator *regulator,
 				   int min_uV, int max_uV);
+unsigned int regulator_get_linear_step(struct regulator *regulator);
 int regulator_set_voltage(struct regulator *regulator, int min_uV, int max_uV);
 int regulator_set_voltage_time(struct regulator *regulator,
 			       int old_uV, int new_uV);