forked from Minki/linux
arm64: dts: ti: Add support for AM62-SK
AM62 StarterKit (SK) board is a low cost, small form factor board designed for TI’s AM625 SoC. It supports the following interfaces: * 2 GB DDR4 RAM * x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode * x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display * x1 Headphone Jack * x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port * x1 UHS-1 capable µSD card slot * 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837 * 512 Mbit OSPI flash * x4 UART through UART-USB bridge * XDS110 for onboard JTAG debug using USB * Temperature sensors, user push buttons and LEDs * 40-pin User Expansion Connector * 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO) * 20-pin header for Programmable Realtime Unit (PRU) IO pins * 15-pin CSI header Add basic support for AM62-SK. Schematics: https://www.ti.com/lit/zip/sprr448 Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Bryan Brattlof <bb@ti.com> Link: https://lore.kernel.org/r/20220225120239.1303821-6-vigneshr@ti.com
This commit is contained in:
Nishanth Menon
parent
f1d17330a5
commit
a033588ec6
@ -21,3 +21,5 @@ dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb
|
||||
|
||||
dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
|
||||
dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
|
||||
|
||||
dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
|
||||
|
||||
206
arch/arm64/boot/dts/ti/k3-am625-sk.dts
Normal file
206
arch/arm64/boot/dts/ti/k3-am625-sk.dts
Normal file
@ -0,0 +1,206 @@
|
||||
// SPDX-License-Identifier: GPL-2.0
|
||||
/*
|
||||
* AM625 SK: https://www.ti.com/lit/zip/sprr448
|
||||
*
|
||||
* Copyright (C) 2021-2022 Texas Instruments Incorporated - https://www.ti.com/
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/leds/common.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include "k3-am625.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "ti,am625-sk", "ti,am625";
|
||||
model = "Texas Instruments AM625 SK";
|
||||
|
||||
aliases {
|
||||
serial2 = &main_uart0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial2:115200n8";
|
||||
bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
|
||||
};
|
||||
|
||||
memory@80000000 {
|
||||
device_type = "memory";
|
||||
/* 2G RAM */
|
||||
reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
|
||||
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <2>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
secure_tfa_ddr: tfa@9e780000 {
|
||||
reg = <0x00 0x9e780000 0x00 0x80000>;
|
||||
alignment = <0x1000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
secure_ddr: optee@9e800000 {
|
||||
reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
|
||||
alignment = <0x1000>;
|
||||
no-map;
|
||||
};
|
||||
|
||||
wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 {
|
||||
compatible = "shared-dma-pool";
|
||||
reg = <0x00 0x9db00000 0x00 0xc00000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
|
||||
vmain_pd: regulator-0 {
|
||||
/* TPS65988 PD CONTROLLER OUTPUT */
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vmain_pd";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
};
|
||||
|
||||
vcc_5v0: regulator-1 {
|
||||
/* Output of LM34936 */
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc_5v0";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
vin-supply = <&vmain_pd>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
};
|
||||
|
||||
vcc_3v3_sys: regulator-2 {
|
||||
/* output of LM61460-Q1 */
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "vcc_3v3_sys";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
vin-supply = <&vmain_pd>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&usr_led_pins_default>;
|
||||
|
||||
led-0 {
|
||||
label = "am62-sk:green:heartbeat";
|
||||
gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
function = LED_FUNCTION_HEARTBEAT;
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&main_pmx0 {
|
||||
main_uart0_pins_default: main-uart0-pins-default {
|
||||
pinctrl-single,pins = <
|
||||
AM62X_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14) UART0_RXD */
|
||||
AM62X_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */
|
||||
>;
|
||||
};
|
||||
|
||||
main_i2c0_pins_default: main-i2c0-pins-default {
|
||||
pinctrl-single,pins = <
|
||||
AM62X_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */
|
||||
AM62X_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */
|
||||
>;
|
||||
};
|
||||
|
||||
main_i2c1_pins_default: main-i2c1-pins-default {
|
||||
pinctrl-single,pins = <
|
||||
AM62X_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
|
||||
AM62X_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
|
||||
>;
|
||||
};
|
||||
|
||||
usr_led_pins_default: usr-led-pins-default {
|
||||
pinctrl-single,pins = <
|
||||
AM62X_IOPAD(0x244, PIN_OUTPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
&wkup_uart0 {
|
||||
/* WKUP UART0 is used by DM firmware */
|
||||
status = "reserved";
|
||||
};
|
||||
|
||||
&mcu_uart0 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&main_uart0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&main_uart0_pins_default>;
|
||||
};
|
||||
|
||||
&main_uart1 {
|
||||
/* Main UART1 is used by TIFS firmware */
|
||||
status = "reserved";
|
||||
};
|
||||
|
||||
&main_uart2 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&main_uart3 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&main_uart4 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&main_uart5 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&main_uart6 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&mcu_i2c0 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&wkup_i2c0 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&main_i2c0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&main_i2c0_pins_default>;
|
||||
clock-frequency = <400000>;
|
||||
};
|
||||
|
||||
&main_i2c1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&main_i2c1_pins_default>;
|
||||
clock-frequency = <400000>;
|
||||
};
|
||||
|
||||
&main_i2c2 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&main_i2c3 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&mailbox0_cluster0 {
|
||||
mbox_m4_0: mbox-m4-0 {
|
||||
ti,mbox-rx = <0 0 0>;
|
||||
ti,mbox-tx = <1 0 0>;
|
||||
};
|
||||
};
|
||||
Loading…
Reference in New Issue
Block a user