Staging: w35und: move hal_init_hardware() and hal_halt() int wbusb.c

Impact: cleanup

The hal_init_hardware() and hal_halt() functions are only used in
wbusb.c so move them there.

Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit is contained in:
Pekka Enberg 2009-04-08 11:13:57 +03:00 committed by Greg Kroah-Hartman
parent 2659851122
commit 80767e6e1e
3 changed files with 345 additions and 348 deletions

View File

@ -23,352 +23,6 @@ void hal_get_permanent_address( struct hw_data * pHwData, u8 *pethernet_address
memcpy( pethernet_address, pHwData->PermanentMacAddress, 6 );
}
static void hal_led_control(unsigned long data)
{
struct wbsoft_priv *adapter = (struct wbsoft_priv *) data;
struct hw_data * pHwData = &adapter->sHwData;
struct wb35_reg *reg = &pHwData->reg;
u32 LEDSet = (pHwData->SoftwareSet & HAL_LED_SET_MASK) >> HAL_LED_SET_SHIFT;
u8 LEDgray[20] = { 0,3,4,6,8,10,11,12,13,14,15,14,13,12,11,10,8,6,4,2 };
u8 LEDgray2[30] = { 7,8,9,10,11,12,13,14,15,0,0,0,0,0,0,0,0,0,0,0,0,0,15,14,13,12,11,10,9,8 };
u32 TimeInterval = 500, ltmp, ltmp2;
ltmp=0;
if( pHwData->SurpriseRemove ) return;
if( pHwData->LED_control ) {
ltmp2 = pHwData->LED_control & 0xff;
if( ltmp2 == 5 ) // 5 is WPS mode
{
TimeInterval = 100;
ltmp2 = (pHwData->LED_control>>8) & 0xff;
switch( ltmp2 )
{
case 1: // [0.2 On][0.1 Off]...
pHwData->LED_Blinking %= 3;
ltmp = 0x1010; // Led 1 & 0 Green and Red
if( pHwData->LED_Blinking == 2 ) // Turn off
ltmp = 0;
break;
case 2: // [0.1 On][0.1 Off]...
pHwData->LED_Blinking %= 2;
ltmp = 0x0010; // Led 0 red color
if( pHwData->LED_Blinking ) // Turn off
ltmp = 0;
break;
case 3: // [0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.5 Off]...
pHwData->LED_Blinking %= 15;
ltmp = 0x0010; // Led 0 red color
if( (pHwData->LED_Blinking >= 9) || (pHwData->LED_Blinking%2) ) // Turn off 0.6 sec
ltmp = 0;
break;
case 4: // [300 On][ off ]
ltmp = 0x1000; // Led 1 Green color
if( pHwData->LED_Blinking >= 3000 )
ltmp = 0; // led maybe on after 300sec * 32bit counter overlap.
break;
}
pHwData->LED_Blinking++;
reg->U1BC_LEDConfigure = ltmp;
if( LEDSet != 7 ) // Only 111 mode has 2 LEDs on PCB.
{
reg->U1BC_LEDConfigure |= (ltmp &0xff)<<8; // Copy LED result to each LED control register
reg->U1BC_LEDConfigure |= (ltmp &0xff00)>>8;
}
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure );
}
}
else if( pHwData->CurrentRadioSw || pHwData->CurrentRadioHw ) // If radio off
{
if( reg->U1BC_LEDConfigure & 0x1010 )
{
reg->U1BC_LEDConfigure &= ~0x1010;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure );
}
}
else
{
switch( LEDSet )
{
case 4: // [100] Only 1 Led be placed on PCB and use pin 21 of IC. Use LED_0 for showing
if( !pHwData->LED_LinkOn ) // Blink only if not Link On
{
// Blinking if scanning is on progress
if( pHwData->LED_Scanning )
{
if( pHwData->LED_Blinking == 0 )
{
reg->U1BC_LEDConfigure |= 0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 On
pHwData->LED_Blinking = 1;
TimeInterval = 300;
}
else
{
reg->U1BC_LEDConfigure &= ~0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off
pHwData->LED_Blinking = 0;
TimeInterval = 300;
}
}
else
{
//Turn Off LED_0
if( reg->U1BC_LEDConfigure & 0x10 )
{
reg->U1BC_LEDConfigure &= ~0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off
}
}
}
else
{
// Turn On LED_0
if( (reg->U1BC_LEDConfigure & 0x10) == 0 )
{
reg->U1BC_LEDConfigure |= 0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off
}
}
break;
case 6: // [110] Only 1 Led be placed on PCB and use pin 21 of IC. Use LED_0 for showing
if( !pHwData->LED_LinkOn ) // Blink only if not Link On
{
// Blinking if scanning is on progress
if( pHwData->LED_Scanning )
{
if( pHwData->LED_Blinking == 0 )
{
reg->U1BC_LEDConfigure &= ~0xf;
reg->U1BC_LEDConfigure |= 0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 On
pHwData->LED_Blinking = 1;
TimeInterval = 300;
}
else
{
reg->U1BC_LEDConfigure &= ~0x1f;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off
pHwData->LED_Blinking = 0;
TimeInterval = 300;
}
}
else
{
// 20060901 Gray blinking if in disconnect state and not scanning
ltmp = reg->U1BC_LEDConfigure;
reg->U1BC_LEDConfigure &= ~0x1f;
if( LEDgray2[(pHwData->LED_Blinking%30)] )
{
reg->U1BC_LEDConfigure |= 0x10;
reg->U1BC_LEDConfigure |= LEDgray2[ (pHwData->LED_Blinking%30) ];
}
pHwData->LED_Blinking++;
if( reg->U1BC_LEDConfigure != ltmp )
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off
TimeInterval = 100;
}
}
else
{
// Turn On LED_0
if( (reg->U1BC_LEDConfigure & 0x10) == 0 )
{
reg->U1BC_LEDConfigure |= 0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off
}
}
break;
case 5: // [101] Only 1 Led be placed on PCB and use LED_1 for showing
if( !pHwData->LED_LinkOn ) // Blink only if not Link On
{
// Blinking if scanning is on progress
if( pHwData->LED_Scanning )
{
if( pHwData->LED_Blinking == 0 )
{
reg->U1BC_LEDConfigure |= 0x1000;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 On
pHwData->LED_Blinking = 1;
TimeInterval = 300;
}
else
{
reg->U1BC_LEDConfigure &= ~0x1000;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 Off
pHwData->LED_Blinking = 0;
TimeInterval = 300;
}
}
else
{
//Turn Off LED_1
if( reg->U1BC_LEDConfigure & 0x1000 )
{
reg->U1BC_LEDConfigure &= ~0x1000;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 Off
}
}
}
else
{
// Is transmitting/receiving ??
if( (adapter->RxByteCount != pHwData->RxByteCountLast ) ||
(adapter->TxByteCount != pHwData->TxByteCountLast ) )
{
if( (reg->U1BC_LEDConfigure & 0x3000) != 0x3000 )
{
reg->U1BC_LEDConfigure |= 0x3000;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 On
}
// Update variable
pHwData->RxByteCountLast = adapter->RxByteCount;
pHwData->TxByteCountLast = adapter->TxByteCount;
TimeInterval = 200;
}
else
{
// Turn On LED_1 and blinking if transmitting/receiving
if( (reg->U1BC_LEDConfigure & 0x3000) != 0x1000 )
{
reg->U1BC_LEDConfigure &= ~0x3000;
reg->U1BC_LEDConfigure |= 0x1000;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 On
}
}
}
break;
default: // Default setting. 2 LED be placed on PCB. LED_0: Link On LED_1 Active
if( (reg->U1BC_LEDConfigure & 0x3000) != 0x3000 )
{
reg->U1BC_LEDConfigure |= 0x3000;// LED_1 is always on and event enable
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure );
}
if( pHwData->LED_Blinking )
{
// Gray blinking
reg->U1BC_LEDConfigure &= ~0x0f;
reg->U1BC_LEDConfigure |= 0x10;
reg->U1BC_LEDConfigure |= LEDgray[ (pHwData->LED_Blinking-1)%20 ];
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure );
pHwData->LED_Blinking += 2;
if( pHwData->LED_Blinking < 40 )
TimeInterval = 100;
else
{
pHwData->LED_Blinking = 0; // Stop blinking
reg->U1BC_LEDConfigure &= ~0x0f;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure );
}
break;
}
if( pHwData->LED_LinkOn )
{
if( !(reg->U1BC_LEDConfigure & 0x10) ) // Check the LED_0
{
//Try to turn ON LED_0 after gray blinking
reg->U1BC_LEDConfigure |= 0x10;
pHwData->LED_Blinking = 1; //Start blinking
TimeInterval = 50;
}
}
else
{
if( reg->U1BC_LEDConfigure & 0x10 ) // Check the LED_0
{
reg->U1BC_LEDConfigure &= ~0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure );
}
}
break;
}
//20060828.1 Active send null packet to avoid AP disconnect
if( pHwData->LED_LinkOn )
{
pHwData->NullPacketCount += TimeInterval;
if( pHwData->NullPacketCount >= DEFAULT_NULL_PACKET_COUNT )
{
pHwData->NullPacketCount = 0;
}
}
}
pHwData->time_count += TimeInterval;
Wb35Tx_CurrentTime(adapter, pHwData->time_count); // 20060928 add
pHwData->LEDTimer.expires = jiffies + msecs_to_jiffies(TimeInterval);
add_timer(&pHwData->LEDTimer);
}
u8 hal_init_hardware(struct ieee80211_hw *hw)
{
struct wbsoft_priv *priv = hw->priv;
struct hw_data * pHwData = &priv->sHwData;
u16 SoftwareSet;
// Initial the variable
pHwData->MaxReceiveLifeTime = DEFAULT_MSDU_LIFE_TIME; // Setting Rx maximum MSDU life time
pHwData->FragmentThreshold = DEFAULT_FRAGMENT_THRESHOLD; // Setting default fragment threshold
pHwData->InitialResource = 1;
if( Wb35Reg_initial(pHwData)) {
pHwData->InitialResource = 2;
if (Wb35Tx_initial(pHwData)) {
pHwData->InitialResource = 3;
if (Wb35Rx_initial(pHwData)) {
pHwData->InitialResource = 4;
init_timer(&pHwData->LEDTimer);
pHwData->LEDTimer.function = hal_led_control;
pHwData->LEDTimer.data = (unsigned long) priv;
pHwData->LEDTimer.expires = jiffies + msecs_to_jiffies(1000);
add_timer(&pHwData->LEDTimer);
//
// For restrict to vendor's hardware
//
SoftwareSet = hal_software_set( pHwData );
#ifdef Vendor2
// Try to make sure the EEPROM contain
SoftwareSet >>= 8;
if( SoftwareSet != 0x82 )
return false;
#endif
Wb35Rx_start(hw);
Wb35Tx_EP2VM_start(priv);
return true;
}
}
}
pHwData->SurpriseRemove = 1;
return false;
}
void hal_halt(struct hw_data * pHwData, void *ppa_data)
{
switch( pHwData->InitialResource )
{
case 4:
case 3: del_timer_sync(&pHwData->LEDTimer);
msleep(100); // Wait for Timer DPC exit 940623.2
Wb35Rx_destroy( pHwData ); // Release the Rx
case 2: Wb35Tx_destroy( pHwData ); // Release the Tx
case 1: Wb35Reg_destroy( pHwData ); // Release the Wb35 Regisster resources
}
}
//---------------------------------------------------------------------------------------------------
void hal_set_beacon_period( struct hw_data * pHwData, u16 beacon_period )
{

View File

@ -21,7 +21,6 @@ void hal_clear_all_key( struct hw_data * pHwData );
void hal_get_ethernet_address( struct hw_data * pHwData, u8 *current_address );
void hal_set_ethernet_address( struct hw_data * pHwData, u8 *current_address );
void hal_get_permanent_address( struct hw_data * pHwData, u8 *pethernet_address );
u8 hal_init_hardware(struct ieee80211_hw *hw);
void hal_set_power_save_mode( struct hw_data * pHwData, unsigned char power_save, unsigned char wakeup, unsigned char dtim );
void hal_get_power_save_mode( struct hw_data * pHwData, u8 *pin_pwr_save );
void hal_set_slot_time( struct hw_data * pHwData, u8 type );
@ -42,7 +41,6 @@ void hal_set_accept_broadcast( struct hw_data * pHwData, u8 enable );
void hal_set_accept_multicast( struct hw_data * pHwData, u8 enable );
void hal_set_accept_beacon( struct hw_data * pHwData, u8 enable );
void hal_stop( struct hw_data * pHwData );
void hal_halt( struct hw_data * pHwData, void *ppa_data );
void hal_start_tx0( struct hw_data * pHwData );
void hal_set_phy_type( struct hw_data * pHwData, u8 PhyType );
#define hal_get_cwmin( _A ) ( (_A)->cwmin )

View File

@ -178,6 +178,351 @@ static const struct ieee80211_ops wbsoft_ops = {
// conf_tx: hal_set_cwmin()/hal_set_cwmax;
};
static void hal_halt(struct hw_data *pHwData, void *ppa_data)
{
switch( pHwData->InitialResource )
{
case 4:
case 3: del_timer_sync(&pHwData->LEDTimer);
msleep(100); // Wait for Timer DPC exit 940623.2
Wb35Rx_destroy( pHwData ); // Release the Rx
case 2: Wb35Tx_destroy( pHwData ); // Release the Tx
case 1: Wb35Reg_destroy( pHwData ); // Release the Wb35 Regisster resources
}
}
static void hal_led_control(unsigned long data)
{
struct wbsoft_priv *adapter = (struct wbsoft_priv *) data;
struct hw_data * pHwData = &adapter->sHwData;
struct wb35_reg *reg = &pHwData->reg;
u32 LEDSet = (pHwData->SoftwareSet & HAL_LED_SET_MASK) >> HAL_LED_SET_SHIFT;
u8 LEDgray[20] = { 0,3,4,6,8,10,11,12,13,14,15,14,13,12,11,10,8,6,4,2 };
u8 LEDgray2[30] = { 7,8,9,10,11,12,13,14,15,0,0,0,0,0,0,0,0,0,0,0,0,0,15,14,13,12,11,10,9,8 };
u32 TimeInterval = 500, ltmp, ltmp2;
ltmp=0;
if( pHwData->SurpriseRemove ) return;
if( pHwData->LED_control ) {
ltmp2 = pHwData->LED_control & 0xff;
if( ltmp2 == 5 ) // 5 is WPS mode
{
TimeInterval = 100;
ltmp2 = (pHwData->LED_control>>8) & 0xff;
switch( ltmp2 )
{
case 1: // [0.2 On][0.1 Off]...
pHwData->LED_Blinking %= 3;
ltmp = 0x1010; // Led 1 & 0 Green and Red
if( pHwData->LED_Blinking == 2 ) // Turn off
ltmp = 0;
break;
case 2: // [0.1 On][0.1 Off]...
pHwData->LED_Blinking %= 2;
ltmp = 0x0010; // Led 0 red color
if( pHwData->LED_Blinking ) // Turn off
ltmp = 0;
break;
case 3: // [0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.1 On][0.1 Off][0.5 Off]...
pHwData->LED_Blinking %= 15;
ltmp = 0x0010; // Led 0 red color
if( (pHwData->LED_Blinking >= 9) || (pHwData->LED_Blinking%2) ) // Turn off 0.6 sec
ltmp = 0;
break;
case 4: // [300 On][ off ]
ltmp = 0x1000; // Led 1 Green color
if( pHwData->LED_Blinking >= 3000 )
ltmp = 0; // led maybe on after 300sec * 32bit counter overlap.
break;
}
pHwData->LED_Blinking++;
reg->U1BC_LEDConfigure = ltmp;
if( LEDSet != 7 ) // Only 111 mode has 2 LEDs on PCB.
{
reg->U1BC_LEDConfigure |= (ltmp &0xff)<<8; // Copy LED result to each LED control register
reg->U1BC_LEDConfigure |= (ltmp &0xff00)>>8;
}
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure );
}
}
else if( pHwData->CurrentRadioSw || pHwData->CurrentRadioHw ) // If radio off
{
if( reg->U1BC_LEDConfigure & 0x1010 )
{
reg->U1BC_LEDConfigure &= ~0x1010;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure );
}
}
else
{
switch( LEDSet )
{
case 4: // [100] Only 1 Led be placed on PCB and use pin 21 of IC. Use LED_0 for showing
if( !pHwData->LED_LinkOn ) // Blink only if not Link On
{
// Blinking if scanning is on progress
if( pHwData->LED_Scanning )
{
if( pHwData->LED_Blinking == 0 )
{
reg->U1BC_LEDConfigure |= 0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 On
pHwData->LED_Blinking = 1;
TimeInterval = 300;
}
else
{
reg->U1BC_LEDConfigure &= ~0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off
pHwData->LED_Blinking = 0;
TimeInterval = 300;
}
}
else
{
//Turn Off LED_0
if( reg->U1BC_LEDConfigure & 0x10 )
{
reg->U1BC_LEDConfigure &= ~0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off
}
}
}
else
{
// Turn On LED_0
if( (reg->U1BC_LEDConfigure & 0x10) == 0 )
{
reg->U1BC_LEDConfigure |= 0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off
}
}
break;
case 6: // [110] Only 1 Led be placed on PCB and use pin 21 of IC. Use LED_0 for showing
if( !pHwData->LED_LinkOn ) // Blink only if not Link On
{
// Blinking if scanning is on progress
if( pHwData->LED_Scanning )
{
if( pHwData->LED_Blinking == 0 )
{
reg->U1BC_LEDConfigure &= ~0xf;
reg->U1BC_LEDConfigure |= 0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 On
pHwData->LED_Blinking = 1;
TimeInterval = 300;
}
else
{
reg->U1BC_LEDConfigure &= ~0x1f;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off
pHwData->LED_Blinking = 0;
TimeInterval = 300;
}
}
else
{
// 20060901 Gray blinking if in disconnect state and not scanning
ltmp = reg->U1BC_LEDConfigure;
reg->U1BC_LEDConfigure &= ~0x1f;
if( LEDgray2[(pHwData->LED_Blinking%30)] )
{
reg->U1BC_LEDConfigure |= 0x10;
reg->U1BC_LEDConfigure |= LEDgray2[ (pHwData->LED_Blinking%30) ];
}
pHwData->LED_Blinking++;
if( reg->U1BC_LEDConfigure != ltmp )
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off
TimeInterval = 100;
}
}
else
{
// Turn On LED_0
if( (reg->U1BC_LEDConfigure & 0x10) == 0 )
{
reg->U1BC_LEDConfigure |= 0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_0 Off
}
}
break;
case 5: // [101] Only 1 Led be placed on PCB and use LED_1 for showing
if( !pHwData->LED_LinkOn ) // Blink only if not Link On
{
// Blinking if scanning is on progress
if( pHwData->LED_Scanning )
{
if( pHwData->LED_Blinking == 0 )
{
reg->U1BC_LEDConfigure |= 0x1000;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 On
pHwData->LED_Blinking = 1;
TimeInterval = 300;
}
else
{
reg->U1BC_LEDConfigure &= ~0x1000;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 Off
pHwData->LED_Blinking = 0;
TimeInterval = 300;
}
}
else
{
//Turn Off LED_1
if( reg->U1BC_LEDConfigure & 0x1000 )
{
reg->U1BC_LEDConfigure &= ~0x1000;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 Off
}
}
}
else
{
// Is transmitting/receiving ??
if( (adapter->RxByteCount != pHwData->RxByteCountLast ) ||
(adapter->TxByteCount != pHwData->TxByteCountLast ) )
{
if( (reg->U1BC_LEDConfigure & 0x3000) != 0x3000 )
{
reg->U1BC_LEDConfigure |= 0x3000;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 On
}
// Update variable
pHwData->RxByteCountLast = adapter->RxByteCount;
pHwData->TxByteCountLast = adapter->TxByteCount;
TimeInterval = 200;
}
else
{
// Turn On LED_1 and blinking if transmitting/receiving
if( (reg->U1BC_LEDConfigure & 0x3000) != 0x1000 )
{
reg->U1BC_LEDConfigure &= ~0x3000;
reg->U1BC_LEDConfigure |= 0x1000;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure ); // LED_1 On
}
}
}
break;
default: // Default setting. 2 LED be placed on PCB. LED_0: Link On LED_1 Active
if( (reg->U1BC_LEDConfigure & 0x3000) != 0x3000 )
{
reg->U1BC_LEDConfigure |= 0x3000;// LED_1 is always on and event enable
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure );
}
if( pHwData->LED_Blinking )
{
// Gray blinking
reg->U1BC_LEDConfigure &= ~0x0f;
reg->U1BC_LEDConfigure |= 0x10;
reg->U1BC_LEDConfigure |= LEDgray[ (pHwData->LED_Blinking-1)%20 ];
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure );
pHwData->LED_Blinking += 2;
if( pHwData->LED_Blinking < 40 )
TimeInterval = 100;
else
{
pHwData->LED_Blinking = 0; // Stop blinking
reg->U1BC_LEDConfigure &= ~0x0f;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure );
}
break;
}
if( pHwData->LED_LinkOn )
{
if( !(reg->U1BC_LEDConfigure & 0x10) ) // Check the LED_0
{
//Try to turn ON LED_0 after gray blinking
reg->U1BC_LEDConfigure |= 0x10;
pHwData->LED_Blinking = 1; //Start blinking
TimeInterval = 50;
}
}
else
{
if( reg->U1BC_LEDConfigure & 0x10 ) // Check the LED_0
{
reg->U1BC_LEDConfigure &= ~0x10;
Wb35Reg_Write( pHwData, 0x03bc, reg->U1BC_LEDConfigure );
}
}
break;
}
//20060828.1 Active send null packet to avoid AP disconnect
if( pHwData->LED_LinkOn )
{
pHwData->NullPacketCount += TimeInterval;
if( pHwData->NullPacketCount >= DEFAULT_NULL_PACKET_COUNT )
{
pHwData->NullPacketCount = 0;
}
}
}
pHwData->time_count += TimeInterval;
Wb35Tx_CurrentTime(adapter, pHwData->time_count); // 20060928 add
pHwData->LEDTimer.expires = jiffies + msecs_to_jiffies(TimeInterval);
add_timer(&pHwData->LEDTimer);
}
static u8 hal_init_hardware(struct ieee80211_hw *hw)
{
struct wbsoft_priv *priv = hw->priv;
struct hw_data * pHwData = &priv->sHwData;
u16 SoftwareSet;
// Initial the variable
pHwData->MaxReceiveLifeTime = DEFAULT_MSDU_LIFE_TIME; // Setting Rx maximum MSDU life time
pHwData->FragmentThreshold = DEFAULT_FRAGMENT_THRESHOLD; // Setting default fragment threshold
pHwData->InitialResource = 1;
if( Wb35Reg_initial(pHwData)) {
pHwData->InitialResource = 2;
if (Wb35Tx_initial(pHwData)) {
pHwData->InitialResource = 3;
if (Wb35Rx_initial(pHwData)) {
pHwData->InitialResource = 4;
init_timer(&pHwData->LEDTimer);
pHwData->LEDTimer.function = hal_led_control;
pHwData->LEDTimer.data = (unsigned long) priv;
pHwData->LEDTimer.expires = jiffies + msecs_to_jiffies(1000);
add_timer(&pHwData->LEDTimer);
//
// For restrict to vendor's hardware
//
SoftwareSet = hal_software_set( pHwData );
#ifdef Vendor2
// Try to make sure the EEPROM contain
SoftwareSet >>= 8;
if( SoftwareSet != 0x82 )
return false;
#endif
Wb35Rx_start(hw);
Wb35Tx_EP2VM_start(priv);
return true;
}
}
}
pHwData->SurpriseRemove = 1;
return false;
}
static int wb35_hw_init(struct ieee80211_hw *hw)
{
struct wbsoft_priv *priv = hw->priv;