diff --git a/drivers/net/wireless/realtek/rtl8xxxu/Makefile b/drivers/net/wireless/realtek/rtl8xxxu/Makefile index 2b019a611a61..d27128c5c002 100644 --- a/drivers/net/wireless/realtek/rtl8xxxu/Makefile +++ b/drivers/net/wireless/realtek/rtl8xxxu/Makefile @@ -1,3 +1,3 @@ obj-$(CONFIG_RTL8XXXU) += rtl8xxxu.o -rtl8xxxu-y := rtl8xxxu_core.o rtl8xxxu_8192e.o +rtl8xxxu-y := rtl8xxxu_core.o rtl8xxxu_8192e.o rtl8xxxu_8723b.o diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h index 945e04e13de4..2807cb5e7920 100644 --- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h +++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.h @@ -1383,9 +1383,15 @@ int rtl8xxxu_init_phy_rf(struct rtl8xxxu_priv *priv, int rtl8xxxu_init_phy_regs(struct rtl8xxxu_priv *priv, struct rtl8xxxu_reg32val *array); int rtl8xxxu_load_firmware(struct rtl8xxxu_priv *priv, char *fw_name); +void rtl8xxxu_firmware_self_reset(struct rtl8xxxu_priv *priv); void rtl8xxxu_power_off(struct rtl8xxxu_priv *priv); void rtl8xxxu_reset_8051(struct rtl8xxxu_priv *priv); int rtl8xxxu_auto_llt_table(struct rtl8xxxu_priv *priv, u8 last_tx_page); +void rtl8xxxu_prepare_calibrate(struct rtl8xxxu_priv *priv, u8 start); +int rtl8xxxu_flush_fifo(struct rtl8xxxu_priv *priv); +int rtl8723a_h2c_cmd(struct rtl8xxxu_priv *priv, struct h2c_cmd *h2c, int len); +int rtl8xxxu_active_to_lps(struct rtl8xxxu_priv *priv); +void rtl8723a_disabled_to_emu(struct rtl8xxxu_priv *priv); void rtl8xxxu_gen2_config_channel(struct ieee80211_hw *hw); void rtl8xxxu_gen2_usb_quirks(struct rtl8xxxu_priv *priv); void rtl8xxxu_gen2_update_rate_mask(struct rtl8xxxu_priv *priv, @@ -1400,3 +1406,4 @@ bool rtl8xxxu_gen2_simularity_compare(struct rtl8xxxu_priv *priv, int result[][8], int c1, int c2); extern struct rtl8xxxu_fileops rtl8192eu_fops; +extern struct rtl8xxxu_fileops rtl8723bu_fops; diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8723b.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8723b.c new file mode 100644 index 000000000000..7d06dcaf3470 --- /dev/null +++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8723b.c @@ -0,0 +1,1684 @@ +/* + * RTL8XXXU mac80211 USB driver - 8723b specific subdriver + * + * Copyright (c) 2014 - 2016 Jes Sorensen + * + * Portions, notably calibration code: + * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved. + * + * This driver was written as a replacement for the vendor provided + * rtl8723au driver. As the Realtek 8xxx chips are very similar in + * their programming interface, I have started adding support for + * additional 8xxx chips like the 8192cu, 8188cus, etc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of version 2 of the GNU General Public License as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "rtl8xxxu.h" +#include "rtl8xxxu_regs.h" + +static struct rtl8xxxu_reg8val rtl8723b_mac_init_table[] = { + {0x02f, 0x30}, {0x035, 0x00}, {0x039, 0x08}, {0x04e, 0xe0}, + {0x064, 0x00}, {0x067, 0x20}, {0x428, 0x0a}, {0x429, 0x10}, + {0x430, 0x00}, {0x431, 0x00}, + {0x432, 0x00}, {0x433, 0x01}, {0x434, 0x04}, {0x435, 0x05}, + {0x436, 0x07}, {0x437, 0x08}, {0x43c, 0x04}, {0x43d, 0x05}, + {0x43e, 0x07}, {0x43f, 0x08}, {0x440, 0x5d}, {0x441, 0x01}, + {0x442, 0x00}, {0x444, 0x10}, {0x445, 0x00}, {0x446, 0x00}, + {0x447, 0x00}, {0x448, 0x00}, {0x449, 0xf0}, {0x44a, 0x0f}, + {0x44b, 0x3e}, {0x44c, 0x10}, {0x44d, 0x00}, {0x44e, 0x00}, + {0x44f, 0x00}, {0x450, 0x00}, {0x451, 0xf0}, {0x452, 0x0f}, + {0x453, 0x00}, {0x456, 0x5e}, {0x460, 0x66}, {0x461, 0x66}, + {0x4c8, 0xff}, {0x4c9, 0x08}, {0x4cc, 0xff}, + {0x4cd, 0xff}, {0x4ce, 0x01}, {0x500, 0x26}, {0x501, 0xa2}, + {0x502, 0x2f}, {0x503, 0x00}, {0x504, 0x28}, {0x505, 0xa3}, + {0x506, 0x5e}, {0x507, 0x00}, {0x508, 0x2b}, {0x509, 0xa4}, + {0x50a, 0x5e}, {0x50b, 0x00}, {0x50c, 0x4f}, {0x50d, 0xa4}, + {0x50e, 0x00}, {0x50f, 0x00}, {0x512, 0x1c}, {0x514, 0x0a}, + {0x516, 0x0a}, {0x525, 0x4f}, + {0x550, 0x10}, {0x551, 0x10}, {0x559, 0x02}, {0x55c, 0x50}, + {0x55d, 0xff}, {0x605, 0x30}, {0x608, 0x0e}, {0x609, 0x2a}, + {0x620, 0xff}, {0x621, 0xff}, {0x622, 0xff}, {0x623, 0xff}, + {0x624, 0xff}, {0x625, 0xff}, {0x626, 0xff}, {0x627, 0xff}, + {0x638, 0x50}, {0x63c, 0x0a}, {0x63d, 0x0a}, {0x63e, 0x0e}, + {0x63f, 0x0e}, {0x640, 0x40}, {0x642, 0x40}, {0x643, 0x00}, + {0x652, 0xc8}, {0x66e, 0x05}, {0x700, 0x21}, {0x701, 0x43}, + {0x702, 0x65}, {0x703, 0x87}, {0x708, 0x21}, {0x709, 0x43}, + {0x70a, 0x65}, {0x70b, 0x87}, {0x765, 0x18}, {0x76e, 0x04}, + {0xffff, 0xff}, +}; + +static struct rtl8xxxu_reg32val rtl8723b_phy_1t_init_table[] = { + {0x800, 0x80040000}, {0x804, 0x00000003}, + {0x808, 0x0000fc00}, {0x80c, 0x0000000a}, + {0x810, 0x10001331}, {0x814, 0x020c3d10}, + {0x818, 0x02200385}, {0x81c, 0x00000000}, + {0x820, 0x01000100}, {0x824, 0x00190204}, + {0x828, 0x00000000}, {0x82c, 0x00000000}, + {0x830, 0x00000000}, {0x834, 0x00000000}, + {0x838, 0x00000000}, {0x83c, 0x00000000}, + {0x840, 0x00010000}, {0x844, 0x00000000}, + {0x848, 0x00000000}, {0x84c, 0x00000000}, + {0x850, 0x00000000}, {0x854, 0x00000000}, + {0x858, 0x569a11a9}, {0x85c, 0x01000014}, + {0x860, 0x66f60110}, {0x864, 0x061f0649}, + {0x868, 0x00000000}, {0x86c, 0x27272700}, + {0x870, 0x07000760}, {0x874, 0x25004000}, + {0x878, 0x00000808}, {0x87c, 0x00000000}, + {0x880, 0xb0000c1c}, {0x884, 0x00000001}, + {0x888, 0x00000000}, {0x88c, 0xccc000c0}, + {0x890, 0x00000800}, {0x894, 0xfffffffe}, + {0x898, 0x40302010}, {0x89c, 0x00706050}, + {0x900, 0x00000000}, {0x904, 0x00000023}, + {0x908, 0x00000000}, {0x90c, 0x81121111}, + {0x910, 0x00000002}, {0x914, 0x00000201}, + {0xa00, 0x00d047c8}, {0xa04, 0x80ff800c}, + {0xa08, 0x8c838300}, {0xa0c, 0x2e7f120f}, + {0xa10, 0x9500bb78}, {0xa14, 0x1114d028}, + {0xa18, 0x00881117}, {0xa1c, 0x89140f00}, + {0xa20, 0x1a1b0000}, {0xa24, 0x090e1317}, + {0xa28, 0x00000204}, {0xa2c, 0x00d30000}, + {0xa70, 0x101fbf00}, {0xa74, 0x00000007}, + {0xa78, 0x00000900}, {0xa7c, 0x225b0606}, + {0xa80, 0x21806490}, {0xb2c, 0x00000000}, + {0xc00, 0x48071d40}, {0xc04, 0x03a05611}, + {0xc08, 0x000000e4}, {0xc0c, 0x6c6c6c6c}, + {0xc10, 0x08800000}, {0xc14, 0x40000100}, + {0xc18, 0x08800000}, {0xc1c, 0x40000100}, + {0xc20, 0x00000000}, {0xc24, 0x00000000}, + {0xc28, 0x00000000}, {0xc2c, 0x00000000}, + {0xc30, 0x69e9ac44}, {0xc34, 0x469652af}, + {0xc38, 0x49795994}, {0xc3c, 0x0a97971c}, + {0xc40, 0x1f7c403f}, {0xc44, 0x000100b7}, + {0xc48, 0xec020107}, {0xc4c, 0x007f037f}, + {0xc50, 0x69553420}, {0xc54, 0x43bc0094}, + {0xc58, 0x00013149}, {0xc5c, 0x00250492}, + {0xc60, 0x00000000}, {0xc64, 0x7112848b}, + {0xc68, 0x47c00bff}, {0xc6c, 0x00000036}, + {0xc70, 0x2c7f000d}, {0xc74, 0x020610db}, + {0xc78, 0x0000001f}, {0xc7c, 0x00b91612}, + {0xc80, 0x390000e4}, {0xc84, 0x20f60000}, + {0xc88, 0x40000100}, {0xc8c, 0x20200000}, + {0xc90, 0x00020e1a}, {0xc94, 0x00000000}, + {0xc98, 0x00020e1a}, {0xc9c, 0x00007f7f}, + {0xca0, 0x00000000}, {0xca4, 0x000300a0}, + {0xca8, 0x00000000}, {0xcac, 0x00000000}, + {0xcb0, 0x00000000}, {0xcb4, 0x00000000}, + {0xcb8, 0x00000000}, {0xcbc, 0x28000000}, + {0xcc0, 0x00000000}, {0xcc4, 0x00000000}, + {0xcc8, 0x00000000}, {0xccc, 0x00000000}, + {0xcd0, 0x00000000}, {0xcd4, 0x00000000}, + {0xcd8, 0x64b22427}, {0xcdc, 0x00766932}, + {0xce0, 0x00222222}, {0xce4, 0x00000000}, + {0xce8, 0x37644302}, {0xcec, 0x2f97d40c}, + {0xd00, 0x00000740}, {0xd04, 0x40020401}, + {0xd08, 0x0000907f}, {0xd0c, 0x20010201}, + {0xd10, 0xa0633333}, {0xd14, 0x3333bc53}, + {0xd18, 0x7a8f5b6f}, {0xd2c, 0xcc979975}, + {0xd30, 0x00000000}, {0xd34, 0x80608000}, + {0xd38, 0x00000000}, {0xd3c, 0x00127353}, + {0xd40, 0x00000000}, {0xd44, 0x00000000}, + {0xd48, 0x00000000}, {0xd4c, 0x00000000}, + {0xd50, 0x6437140a}, {0xd54, 0x00000000}, + {0xd58, 0x00000282}, {0xd5c, 0x30032064}, + {0xd60, 0x4653de68}, {0xd64, 0x04518a3c}, + {0xd68, 0x00002101}, {0xd6c, 0x2a201c16}, + {0xd70, 0x1812362e}, {0xd74, 0x322c2220}, + {0xd78, 0x000e3c24}, {0xe00, 0x2d2d2d2d}, + {0xe04, 0x2d2d2d2d}, {0xe08, 0x0390272d}, + {0xe10, 0x2d2d2d2d}, {0xe14, 0x2d2d2d2d}, + {0xe18, 0x2d2d2d2d}, {0xe1c, 0x2d2d2d2d}, + {0xe28, 0x00000000}, {0xe30, 0x1000dc1f}, + {0xe34, 0x10008c1f}, {0xe38, 0x02140102}, + {0xe3c, 0x681604c2}, {0xe40, 0x01007c00}, + {0xe44, 0x01004800}, {0xe48, 0xfb000000}, + {0xe4c, 0x000028d1}, {0xe50, 0x1000dc1f}, + {0xe54, 0x10008c1f}, {0xe58, 0x02140102}, + {0xe5c, 0x28160d05}, {0xe60, 0x00000008}, + {0xe68, 0x001b2556}, {0xe6c, 0x00c00096}, + {0xe70, 0x00c00096}, {0xe74, 0x01000056}, + {0xe78, 0x01000014}, {0xe7c, 0x01000056}, + {0xe80, 0x01000014}, {0xe84, 0x00c00096}, + {0xe88, 0x01000056}, {0xe8c, 0x00c00096}, + {0xed0, 0x00c00096}, {0xed4, 0x00c00096}, + {0xed8, 0x00c00096}, {0xedc, 0x000000d6}, + {0xee0, 0x000000d6}, {0xeec, 0x01c00016}, + {0xf14, 0x00000003}, {0xf4c, 0x00000000}, + {0xf00, 0x00000300}, + {0x820, 0x01000100}, {0x800, 0x83040000}, + {0xffff, 0xffffffff}, +}; + +static struct rtl8xxxu_reg32val rtl8xxx_agc_8723bu_table[] = { + {0xc78, 0xfd000001}, {0xc78, 0xfc010001}, + {0xc78, 0xfb020001}, {0xc78, 0xfa030001}, + {0xc78, 0xf9040001}, {0xc78, 0xf8050001}, + {0xc78, 0xf7060001}, {0xc78, 0xf6070001}, + {0xc78, 0xf5080001}, {0xc78, 0xf4090001}, + {0xc78, 0xf30a0001}, {0xc78, 0xf20b0001}, + {0xc78, 0xf10c0001}, {0xc78, 0xf00d0001}, + {0xc78, 0xef0e0001}, {0xc78, 0xee0f0001}, + {0xc78, 0xed100001}, {0xc78, 0xec110001}, + {0xc78, 0xeb120001}, {0xc78, 0xea130001}, + {0xc78, 0xe9140001}, {0xc78, 0xe8150001}, + {0xc78, 0xe7160001}, {0xc78, 0xe6170001}, + {0xc78, 0xe5180001}, {0xc78, 0xe4190001}, + {0xc78, 0xe31a0001}, {0xc78, 0xa51b0001}, + {0xc78, 0xa41c0001}, {0xc78, 0xa31d0001}, + {0xc78, 0x671e0001}, {0xc78, 0x661f0001}, + {0xc78, 0x65200001}, {0xc78, 0x64210001}, + {0xc78, 0x63220001}, {0xc78, 0x4a230001}, + {0xc78, 0x49240001}, {0xc78, 0x48250001}, + {0xc78, 0x47260001}, {0xc78, 0x46270001}, + {0xc78, 0x45280001}, {0xc78, 0x44290001}, + {0xc78, 0x432a0001}, {0xc78, 0x422b0001}, + {0xc78, 0x292c0001}, {0xc78, 0x282d0001}, + {0xc78, 0x272e0001}, {0xc78, 0x262f0001}, + {0xc78, 0x0a300001}, {0xc78, 0x09310001}, + {0xc78, 0x08320001}, {0xc78, 0x07330001}, + {0xc78, 0x06340001}, {0xc78, 0x05350001}, + {0xc78, 0x04360001}, {0xc78, 0x03370001}, + {0xc78, 0x02380001}, {0xc78, 0x01390001}, + {0xc78, 0x013a0001}, {0xc78, 0x013b0001}, + {0xc78, 0x013c0001}, {0xc78, 0x013d0001}, + {0xc78, 0x013e0001}, {0xc78, 0x013f0001}, + {0xc78, 0xfc400001}, {0xc78, 0xfb410001}, + {0xc78, 0xfa420001}, {0xc78, 0xf9430001}, + {0xc78, 0xf8440001}, {0xc78, 0xf7450001}, + {0xc78, 0xf6460001}, {0xc78, 0xf5470001}, + {0xc78, 0xf4480001}, {0xc78, 0xf3490001}, + {0xc78, 0xf24a0001}, {0xc78, 0xf14b0001}, + {0xc78, 0xf04c0001}, {0xc78, 0xef4d0001}, + {0xc78, 0xee4e0001}, {0xc78, 0xed4f0001}, + {0xc78, 0xec500001}, {0xc78, 0xeb510001}, + {0xc78, 0xea520001}, {0xc78, 0xe9530001}, + {0xc78, 0xe8540001}, {0xc78, 0xe7550001}, + {0xc78, 0xe6560001}, {0xc78, 0xe5570001}, + {0xc78, 0xe4580001}, {0xc78, 0xe3590001}, + {0xc78, 0xa65a0001}, {0xc78, 0xa55b0001}, + {0xc78, 0xa45c0001}, {0xc78, 0xa35d0001}, + {0xc78, 0x675e0001}, {0xc78, 0x665f0001}, + {0xc78, 0x65600001}, {0xc78, 0x64610001}, + {0xc78, 0x63620001}, {0xc78, 0x62630001}, + {0xc78, 0x61640001}, {0xc78, 0x48650001}, + {0xc78, 0x47660001}, {0xc78, 0x46670001}, + {0xc78, 0x45680001}, {0xc78, 0x44690001}, + {0xc78, 0x436a0001}, {0xc78, 0x426b0001}, + {0xc78, 0x286c0001}, {0xc78, 0x276d0001}, + {0xc78, 0x266e0001}, {0xc78, 0x256f0001}, + {0xc78, 0x24700001}, {0xc78, 0x09710001}, + {0xc78, 0x08720001}, {0xc78, 0x07730001}, + {0xc78, 0x06740001}, {0xc78, 0x05750001}, + {0xc78, 0x04760001}, {0xc78, 0x03770001}, + {0xc78, 0x02780001}, {0xc78, 0x01790001}, + {0xc78, 0x017a0001}, {0xc78, 0x017b0001}, + {0xc78, 0x017c0001}, {0xc78, 0x017d0001}, + {0xc78, 0x017e0001}, {0xc78, 0x017f0001}, + {0xc50, 0x69553422}, + {0xc50, 0x69553420}, + {0x824, 0x00390204}, + {0xffff, 0xffffffff} +}; + +static struct rtl8xxxu_rfregval rtl8723bu_radioa_1t_init_table[] = { + {0x00, 0x00010000}, {0xb0, 0x000dffe0}, + {0xfe, 0x00000000}, {0xfe, 0x00000000}, + {0xfe, 0x00000000}, {0xb1, 0x00000018}, + {0xfe, 0x00000000}, {0xfe, 0x00000000}, + {0xfe, 0x00000000}, {0xb2, 0x00084c00}, + {0xb5, 0x0000d2cc}, {0xb6, 0x000925aa}, + {0xb7, 0x00000010}, {0xb8, 0x0000907f}, + {0x5c, 0x00000002}, {0x7c, 0x00000002}, + {0x7e, 0x00000005}, {0x8b, 0x0006fc00}, + {0xb0, 0x000ff9f0}, {0x1c, 0x000739d2}, + {0x1e, 0x00000000}, {0xdf, 0x00000780}, + {0x50, 0x00067435}, + /* + * The 8723bu vendor driver indicates that bit 8 should be set in + * 0x51 for package types TFBGA90, TFBGA80, and TFBGA79. However + * they never actually check the package type - and just default + * to not setting it. + */ + {0x51, 0x0006b04e}, + {0x52, 0x000007d2}, {0x53, 0x00000000}, + {0x54, 0x00050400}, {0x55, 0x0004026e}, + {0xdd, 0x0000004c}, {0x70, 0x00067435}, + /* + * 0x71 has same package type condition as for register 0x51 + */ + {0x71, 0x0006b04e}, + {0x72, 0x000007d2}, {0x73, 0x00000000}, + {0x74, 0x00050400}, {0x75, 0x0004026e}, + {0xef, 0x00000100}, {0x34, 0x0000add7}, + {0x35, 0x00005c00}, {0x34, 0x00009dd4}, + {0x35, 0x00005000}, {0x34, 0x00008dd1}, + {0x35, 0x00004400}, {0x34, 0x00007dce}, + {0x35, 0x00003800}, {0x34, 0x00006cd1}, + {0x35, 0x00004400}, {0x34, 0x00005cce}, + {0x35, 0x00003800}, {0x34, 0x000048ce}, + {0x35, 0x00004400}, {0x34, 0x000034ce}, + {0x35, 0x00003800}, {0x34, 0x00002451}, + {0x35, 0x00004400}, {0x34, 0x0000144e}, + {0x35, 0x00003800}, {0x34, 0x00000051}, + {0x35, 0x00004400}, {0xef, 0x00000000}, + {0xef, 0x00000100}, {0xed, 0x00000010}, + {0x44, 0x0000add7}, {0x44, 0x00009dd4}, + {0x44, 0x00008dd1}, {0x44, 0x00007dce}, + {0x44, 0x00006cc1}, {0x44, 0x00005cce}, + {0x44, 0x000044d1}, {0x44, 0x000034ce}, + {0x44, 0x00002451}, {0x44, 0x0000144e}, + {0x44, 0x00000051}, {0xef, 0x00000000}, + {0xed, 0x00000000}, {0x7f, 0x00020080}, + {0xef, 0x00002000}, {0x3b, 0x000380ef}, + {0x3b, 0x000302fe}, {0x3b, 0x00028ce6}, + {0x3b, 0x000200bc}, {0x3b, 0x000188a5}, + {0x3b, 0x00010fbc}, {0x3b, 0x00008f71}, + {0x3b, 0x00000900}, {0xef, 0x00000000}, + {0xed, 0x00000001}, {0x40, 0x000380ef}, + {0x40, 0x000302fe}, {0x40, 0x00028ce6}, + {0x40, 0x000200bc}, {0x40, 0x000188a5}, + {0x40, 0x00010fbc}, {0x40, 0x00008f71}, + {0x40, 0x00000900}, {0xed, 0x00000000}, + {0x82, 0x00080000}, {0x83, 0x00008000}, + {0x84, 0x00048d80}, {0x85, 0x00068000}, + {0xa2, 0x00080000}, {0xa3, 0x00008000}, + {0xa4, 0x00048d80}, {0xa5, 0x00068000}, + {0xed, 0x00000002}, {0xef, 0x00000002}, + {0x56, 0x00000032}, {0x76, 0x00000032}, + {0x01, 0x00000780}, + {0xff, 0xffffffff} +}; + +static void rtl8723bu_write_btreg(struct rtl8xxxu_priv *priv, u8 reg, u8 data) +{ + struct h2c_cmd h2c; + int reqnum = 0; + + memset(&h2c, 0, sizeof(struct h2c_cmd)); + h2c.bt_mp_oper.cmd = H2C_8723B_BT_MP_OPER; + h2c.bt_mp_oper.operreq = 0 | (reqnum << 4); + h2c.bt_mp_oper.opcode = BT_MP_OP_WRITE_REG_VALUE; + h2c.bt_mp_oper.data = data; + rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_mp_oper)); + + reqnum++; + memset(&h2c, 0, sizeof(struct h2c_cmd)); + h2c.bt_mp_oper.cmd = H2C_8723B_BT_MP_OPER; + h2c.bt_mp_oper.operreq = 0 | (reqnum << 4); + h2c.bt_mp_oper.opcode = BT_MP_OP_WRITE_REG_VALUE; + h2c.bt_mp_oper.addr = reg; + rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_mp_oper)); +} + +static void rtl8723bu_reset_8051(struct rtl8xxxu_priv *priv) +{ + u8 val8; + u16 sys_func; + + val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL); + val8 &= ~BIT(1); + rtl8xxxu_write8(priv, REG_RSV_CTRL, val8); + + val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1); + val8 &= ~BIT(0); + rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8); + + sys_func = rtl8xxxu_read16(priv, REG_SYS_FUNC); + sys_func &= ~SYS_FUNC_CPU_ENABLE; + rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func); + + val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL); + val8 &= ~BIT(1); + rtl8xxxu_write8(priv, REG_RSV_CTRL, val8); + + val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1); + val8 |= BIT(0); + rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8); + + sys_func |= SYS_FUNC_CPU_ENABLE; + rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func); +} + +static void +rtl8723b_set_tx_power(struct rtl8xxxu_priv *priv, int channel, bool ht40) +{ + u32 val32, ofdm, mcs; + u8 cck, ofdmbase, mcsbase; + int group, tx_idx; + + tx_idx = 0; + group = rtl8xxxu_gen2_channel_to_group(channel); + + cck = priv->cck_tx_power_index_B[group]; + val32 = rtl8xxxu_read32(priv, REG_TX_AGC_A_CCK1_MCS32); + val32 &= 0xffff00ff; + val32 |= (cck << 8); + rtl8xxxu_write32(priv, REG_TX_AGC_A_CCK1_MCS32, val32); + + val32 = rtl8xxxu_read32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11); + val32 &= 0xff; + val32 |= ((cck << 8) | (cck << 16) | (cck << 24)); + rtl8xxxu_write32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11, val32); + + ofdmbase = priv->ht40_1s_tx_power_index_B[group]; + ofdmbase += priv->ofdm_tx_power_diff[tx_idx].b; + ofdm = ofdmbase | ofdmbase << 8 | ofdmbase << 16 | ofdmbase << 24; + + rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE18_06, ofdm); + rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE54_24, ofdm); + + mcsbase = priv->ht40_1s_tx_power_index_B[group]; + if (ht40) + mcsbase += priv->ht40_tx_power_diff[tx_idx++].b; + else + mcsbase += priv->ht20_tx_power_diff[tx_idx++].b; + mcs = mcsbase | mcsbase << 8 | mcsbase << 16 | mcsbase << 24; + + rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS03_MCS00, mcs); + rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS07_MCS04, mcs); +} + +static int rtl8723bu_parse_efuse(struct rtl8xxxu_priv *priv) +{ + struct rtl8723bu_efuse *efuse = &priv->efuse_wifi.efuse8723bu; + int i; + + if (efuse->rtl_id != cpu_to_le16(0x8129)) + return -EINVAL; + + ether_addr_copy(priv->mac_addr, efuse->mac_addr); + + memcpy(priv->cck_tx_power_index_A, efuse->tx_power_index_A.cck_base, + sizeof(efuse->tx_power_index_A.cck_base)); + memcpy(priv->cck_tx_power_index_B, efuse->tx_power_index_B.cck_base, + sizeof(efuse->tx_power_index_B.cck_base)); + + memcpy(priv->ht40_1s_tx_power_index_A, + efuse->tx_power_index_A.ht40_base, + sizeof(efuse->tx_power_index_A.ht40_base)); + memcpy(priv->ht40_1s_tx_power_index_B, + efuse->tx_power_index_B.ht40_base, + sizeof(efuse->tx_power_index_B.ht40_base)); + + priv->ofdm_tx_power_diff[0].a = + efuse->tx_power_index_A.ht20_ofdm_1s_diff.a; + priv->ofdm_tx_power_diff[0].b = + efuse->tx_power_index_B.ht20_ofdm_1s_diff.a; + + priv->ht20_tx_power_diff[0].a = + efuse->tx_power_index_A.ht20_ofdm_1s_diff.b; + priv->ht20_tx_power_diff[0].b = + efuse->tx_power_index_B.ht20_ofdm_1s_diff.b; + + priv->ht40_tx_power_diff[0].a = 0; + priv->ht40_tx_power_diff[0].b = 0; + + for (i = 1; i < RTL8723B_TX_COUNT; i++) { + priv->ofdm_tx_power_diff[i].a = + efuse->tx_power_index_A.pwr_diff[i - 1].ofdm; + priv->ofdm_tx_power_diff[i].b = + efuse->tx_power_index_B.pwr_diff[i - 1].ofdm; + + priv->ht20_tx_power_diff[i].a = + efuse->tx_power_index_A.pwr_diff[i - 1].ht20; + priv->ht20_tx_power_diff[i].b = + efuse->tx_power_index_B.pwr_diff[i - 1].ht20; + + priv->ht40_tx_power_diff[i].a = + efuse->tx_power_index_A.pwr_diff[i - 1].ht40; + priv->ht40_tx_power_diff[i].b = + efuse->tx_power_index_B.pwr_diff[i - 1].ht40; + } + + priv->has_xtalk = 1; + priv->xtalk = priv->efuse_wifi.efuse8723bu.xtal_k & 0x3f; + + dev_info(&priv->udev->dev, "Vendor: %.7s\n", efuse->vendor_name); + dev_info(&priv->udev->dev, "Product: %.41s\n", efuse->device_name); + + if (rtl8xxxu_debug & RTL8XXXU_DEBUG_EFUSE) { + int i; + unsigned char *raw = priv->efuse_wifi.raw; + + dev_info(&priv->udev->dev, + "%s: dumping efuse (0x%02zx bytes):\n", + __func__, sizeof(struct rtl8723bu_efuse)); + for (i = 0; i < sizeof(struct rtl8723bu_efuse); i += 8) { + dev_info(&priv->udev->dev, "%02x: " + "%02x %02x %02x %02x %02x %02x %02x %02x\n", i, + raw[i], raw[i + 1], raw[i + 2], + raw[i + 3], raw[i + 4], raw[i + 5], + raw[i + 6], raw[i + 7]); + } + } + + return 0; +} + +static int rtl8723bu_load_firmware(struct rtl8xxxu_priv *priv) +{ + char *fw_name; + int ret; + + if (priv->enable_bluetooth) + fw_name = "rtlwifi/rtl8723bu_bt.bin"; + else + fw_name = "rtlwifi/rtl8723bu_nic.bin"; + + ret = rtl8xxxu_load_firmware(priv, fw_name); + return ret; +} + +static void rtl8723bu_init_phy_bb(struct rtl8xxxu_priv *priv) +{ + u8 val8; + u16 val16; + + val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); + val16 |= SYS_FUNC_BB_GLB_RSTN | SYS_FUNC_BBRSTB | SYS_FUNC_DIO_RF; + rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); + + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00); + + /* 6. 0x1f[7:0] = 0x07 */ + val8 = RF_ENABLE | RF_RSTB | RF_SDMRSTB; + rtl8xxxu_write8(priv, REG_RF_CTRL, val8); + + /* Why? */ + rtl8xxxu_write8(priv, REG_SYS_FUNC, 0xe3); + rtl8xxxu_write8(priv, REG_AFE_XTAL_CTRL + 1, 0x80); + rtl8xxxu_init_phy_regs(priv, rtl8723b_phy_1t_init_table); + + rtl8xxxu_init_phy_regs(priv, rtl8xxx_agc_8723bu_table); +} + +static int rtl8723bu_init_phy_rf(struct rtl8xxxu_priv *priv) +{ + int ret; + + ret = rtl8xxxu_init_phy_rf(priv, rtl8723bu_radioa_1t_init_table, RF_A); + /* + * PHY LCK + */ + rtl8xxxu_write_rfreg(priv, RF_A, 0xb0, 0xdfbe0); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_MODE_AG, 0x8c01); + msleep(200); + rtl8xxxu_write_rfreg(priv, RF_A, 0xb0, 0xdffe0); + + return ret; +} + +static void rtl8723bu_phy_init_antenna_selection(struct rtl8xxxu_priv *priv) +{ + u32 val32; + + val32 = rtl8xxxu_read32(priv, REG_PAD_CTRL1); + val32 &= ~(BIT(20) | BIT(24)); + rtl8xxxu_write32(priv, REG_PAD_CTRL1, val32); + + val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG); + val32 &= ~BIT(4); + rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, val32); + + val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG); + val32 |= BIT(3); + rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, val32); + + val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); + val32 |= BIT(24); + rtl8xxxu_write32(priv, REG_LEDCFG0, val32); + + val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); + val32 &= ~BIT(23); + rtl8xxxu_write32(priv, REG_LEDCFG0, val32); + + val32 = rtl8xxxu_read32(priv, REG_RFE_BUFFER); + val32 |= (BIT(0) | BIT(1)); + rtl8xxxu_write32(priv, REG_RFE_BUFFER, val32); + + val32 = rtl8xxxu_read32(priv, REG_RFE_CTRL_ANTA_SRC); + val32 &= 0xffffff00; + val32 |= 0x77; + rtl8xxxu_write32(priv, REG_RFE_CTRL_ANTA_SRC, val32); + + val32 = rtl8xxxu_read32(priv, REG_PWR_DATA); + val32 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN; + rtl8xxxu_write32(priv, REG_PWR_DATA, val32); +} + +static int rtl8723bu_iqk_path_a(struct rtl8xxxu_priv *priv) +{ + u32 reg_eac, reg_e94, reg_e9c, path_sel, val32; + int result = 0; + + path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH); + + /* + * Leave IQK mode + */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + + /* + * Enable path A PA in TX IQK mode + */ + val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); + val32 |= 0x80000; + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x20000); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0003f); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xc7f87); + + /* + * Tx IQK setting + */ + rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00); + rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800); + + /* path-A IQK setting */ + rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c); + rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c); + rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c); + rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c); + + rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x821403ea); + rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28110000); + rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000); + rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000); + + /* LO calibration setting */ + rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x00462911); + + /* + * Enter IQK mode + */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + val32 |= 0x80800000; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + + /* + * The vendor driver indicates the USB module is always using + * S0S1 path 1 for the 8723bu. This may be different for 8192eu + */ + if (priv->rf_paths > 1) + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000); + else + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280); + + /* + * Bit 12 seems to be BT_GRANT, and is only found in the 8723bu. + * No trace of this in the 8192eu or 8188eu vendor drivers. + */ + rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800); + + /* One shot, path A LOK & IQK */ + rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000); + rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000); + + mdelay(1); + + /* Restore Ant Path */ + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel); +#ifdef RTL8723BU_BT + /* GNT_BT = 1 */ + rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800); +#endif + + /* + * Leave IQK mode + */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + + /* Check failed */ + reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2); + reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A); + reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A); + + val32 = (reg_e9c >> 16) & 0x3ff; + if (val32 & 0x200) + val32 = 0x400 - val32; + + if (!(reg_eac & BIT(28)) && + ((reg_e94 & 0x03ff0000) != 0x01420000) && + ((reg_e9c & 0x03ff0000) != 0x00420000) && + ((reg_e94 & 0x03ff0000) < 0x01100000) && + ((reg_e94 & 0x03ff0000) > 0x00f00000) && + val32 < 0xf) + result |= 0x01; + else /* If TX not OK, ignore RX */ + goto out; + +out: + return result; +} + +static int rtl8723bu_rx_iqk_path_a(struct rtl8xxxu_priv *priv) +{ + u32 reg_ea4, reg_eac, reg_e94, reg_e9c, path_sel, val32; + int result = 0; + + path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH); + + /* + * Leave IQK mode + */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + + /* + * Enable path A PA in TX IQK mode + */ + val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); + val32 |= 0x80000; + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7fb7); + + /* + * Tx IQK setting + */ + rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00); + rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800); + + /* path-A IQK setting */ + rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c); + rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c); + rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c); + rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c); + + rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160ff0); + rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28110000); + rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000); + rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000); + + /* LO calibration setting */ + rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a911); + + /* + * Enter IQK mode + */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + val32 |= 0x80800000; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + + /* + * The vendor driver indicates the USB module is always using + * S0S1 path 1 for the 8723bu. This may be different for 8192eu + */ + if (priv->rf_paths > 1) + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000); + else + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280); + + /* + * Bit 12 seems to be BT_GRANT, and is only found in the 8723bu. + * No trace of this in the 8192eu or 8188eu vendor drivers. + */ + rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800); + + /* One shot, path A LOK & IQK */ + rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000); + rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000); + + mdelay(1); + + /* Restore Ant Path */ + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel); +#ifdef RTL8723BU_BT + /* GNT_BT = 1 */ + rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800); +#endif + + /* + * Leave IQK mode + */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + + /* Check failed */ + reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2); + reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A); + reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A); + + val32 = (reg_e9c >> 16) & 0x3ff; + if (val32 & 0x200) + val32 = 0x400 - val32; + + if (!(reg_eac & BIT(28)) && + ((reg_e94 & 0x03ff0000) != 0x01420000) && + ((reg_e9c & 0x03ff0000) != 0x00420000) && + ((reg_e94 & 0x03ff0000) < 0x01100000) && + ((reg_e94 & 0x03ff0000) > 0x00f00000) && + val32 < 0xf) + result |= 0x01; + else /* If TX not OK, ignore RX */ + goto out; + + val32 = 0x80007c00 | (reg_e94 &0x3ff0000) | + ((reg_e9c & 0x3ff0000) >> 16); + rtl8xxxu_write32(priv, REG_TX_IQK, val32); + + /* + * Modify RX IQK mode + */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); + val32 |= 0x80000; + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7d77); + + /* + * PA, PAD setting + */ + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0xf80); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_55, 0x4021f); + + /* + * RX IQK setting + */ + rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800); + + /* path-A IQK setting */ + rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c); + rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x18008c1c); + rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c); + rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c); + + rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82110000); + rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x2816001f); + rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000); + rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000); + + /* LO calibration setting */ + rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a8d1); + + /* + * Enter IQK mode + */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + val32 |= 0x80800000; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + + if (priv->rf_paths > 1) + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000); + else + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280); + + /* + * Disable BT + */ + rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800); + + /* One shot, path A LOK & IQK */ + rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000); + rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000); + + mdelay(1); + + /* Restore Ant Path */ + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel); +#ifdef RTL8723BU_BT + /* GNT_BT = 1 */ + rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800); +#endif + + /* + * Leave IQK mode + */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + + /* Check failed */ + reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2); + reg_ea4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_A_2); + + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x780); + + val32 = (reg_eac >> 16) & 0x3ff; + if (val32 & 0x200) + val32 = 0x400 - val32; + + if (!(reg_eac & BIT(27)) && + ((reg_ea4 & 0x03ff0000) != 0x01320000) && + ((reg_eac & 0x03ff0000) != 0x00360000) && + ((reg_ea4 & 0x03ff0000) < 0x01100000) && + ((reg_ea4 & 0x03ff0000) > 0x00f00000) && + val32 < 0xf) + result |= 0x02; + else /* If TX not OK, ignore RX */ + goto out; +out: + return result; +} + +static void rtl8723bu_phy_iqcalibrate(struct rtl8xxxu_priv *priv, + int result[][8], int t) +{ + struct device *dev = &priv->udev->dev; + u32 i, val32; + int path_a_ok /*, path_b_ok */; + int retry = 2; + const u32 adda_regs[RTL8XXXU_ADDA_REGS] = { + REG_FPGA0_XCD_SWITCH_CTRL, REG_BLUETOOTH, + REG_RX_WAIT_CCA, REG_TX_CCK_RFON, + REG_TX_CCK_BBON, REG_TX_OFDM_RFON, + REG_TX_OFDM_BBON, REG_TX_TO_RX, + REG_TX_TO_TX, REG_RX_CCK, + REG_RX_OFDM, REG_RX_WAIT_RIFS, + REG_RX_TO_RX, REG_STANDBY, + REG_SLEEP, REG_PMPD_ANAEN + }; + const u32 iqk_mac_regs[RTL8XXXU_MAC_REGS] = { + REG_TXPAUSE, REG_BEACON_CTRL, + REG_BEACON_CTRL_1, REG_GPIO_MUXCFG + }; + const u32 iqk_bb_regs[RTL8XXXU_BB_REGS] = { + REG_OFDM0_TRX_PATH_ENABLE, REG_OFDM0_TR_MUX_PAR, + REG_FPGA0_XCD_RF_SW_CTRL, REG_CONFIG_ANT_A, REG_CONFIG_ANT_B, + REG_FPGA0_XAB_RF_SW_CTRL, REG_FPGA0_XA_RF_INT_OE, + REG_FPGA0_XB_RF_INT_OE, REG_FPGA0_RF_MODE + }; + u8 xa_agc = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1) & 0xff; + u8 xb_agc = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1) & 0xff; + + /* + * Note: IQ calibration must be performed after loading + * PHY_REG.txt , and radio_a, radio_b.txt + */ + + if (t == 0) { + /* Save ADDA parameters, turn Path A ADDA on */ + rtl8xxxu_save_regs(priv, adda_regs, priv->adda_backup, + RTL8XXXU_ADDA_REGS); + rtl8xxxu_save_mac_regs(priv, iqk_mac_regs, priv->mac_backup); + rtl8xxxu_save_regs(priv, iqk_bb_regs, + priv->bb_backup, RTL8XXXU_BB_REGS); + } + + rtl8xxxu_path_adda_on(priv, adda_regs, true); + + /* MAC settings */ + rtl8xxxu_mac_calibration(priv, iqk_mac_regs, priv->mac_backup); + + val32 = rtl8xxxu_read32(priv, REG_CCK0_AFE_SETTING); + val32 |= 0x0f000000; + rtl8xxxu_write32(priv, REG_CCK0_AFE_SETTING, val32); + + rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, 0x03a05600); + rtl8xxxu_write32(priv, REG_OFDM0_TR_MUX_PAR, 0x000800e4); + rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_SW_CTRL, 0x22204000); + + /* + * RX IQ calibration setting for 8723B D cut large current issue + * when leaving IPS + */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + + val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); + val32 |= 0x80000; + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); + + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7fb7); + + val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED); + val32 |= 0x20; + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32); + + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_43, 0x60fbd); + + for (i = 0; i < retry; i++) { + path_a_ok = rtl8723bu_iqk_path_a(priv); + if (path_a_ok == 0x01) { + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + + val32 = rtl8xxxu_read32(priv, + REG_TX_POWER_BEFORE_IQK_A); + result[t][0] = (val32 >> 16) & 0x3ff; + val32 = rtl8xxxu_read32(priv, + REG_TX_POWER_AFTER_IQK_A); + result[t][1] = (val32 >> 16) & 0x3ff; + + break; + } + } + + if (!path_a_ok) + dev_dbg(dev, "%s: Path A TX IQK failed!\n", __func__); + + for (i = 0; i < retry; i++) { + path_a_ok = rtl8723bu_rx_iqk_path_a(priv); + if (path_a_ok == 0x03) { + val32 = rtl8xxxu_read32(priv, + REG_RX_POWER_BEFORE_IQK_A_2); + result[t][2] = (val32 >> 16) & 0x3ff; + val32 = rtl8xxxu_read32(priv, + REG_RX_POWER_AFTER_IQK_A_2); + result[t][3] = (val32 >> 16) & 0x3ff; + + break; + } + } + + if (!path_a_ok) + dev_dbg(dev, "%s: Path A RX IQK failed!\n", __func__); + + if (priv->tx_paths > 1) { +#if 1 + dev_warn(dev, "%s: Path B not supported\n", __func__); +#else + + /* + * Path A into standby + */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, 0x10000); + + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + val32 |= 0x80800000; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + + /* Turn Path B ADDA on */ + rtl8xxxu_path_adda_on(priv, adda_regs, false); + + for (i = 0; i < retry; i++) { + path_b_ok = rtl8xxxu_iqk_path_b(priv); + if (path_b_ok == 0x03) { + val32 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B); + result[t][4] = (val32 >> 16) & 0x3ff; + val32 = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B); + result[t][5] = (val32 >> 16) & 0x3ff; + break; + } + } + + if (!path_b_ok) + dev_dbg(dev, "%s: Path B IQK failed!\n", __func__); + + for (i = 0; i < retry; i++) { + path_b_ok = rtl8723bu_rx_iqk_path_b(priv); + if (path_a_ok == 0x03) { + val32 = rtl8xxxu_read32(priv, + REG_RX_POWER_BEFORE_IQK_B_2); + result[t][6] = (val32 >> 16) & 0x3ff; + val32 = rtl8xxxu_read32(priv, + REG_RX_POWER_AFTER_IQK_B_2); + result[t][7] = (val32 >> 16) & 0x3ff; + break; + } + } + + if (!path_b_ok) + dev_dbg(dev, "%s: Path B RX IQK failed!\n", __func__); +#endif + } + + /* Back to BB mode, load original value */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 &= 0x000000ff; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + + if (t) { + /* Reload ADDA power saving parameters */ + rtl8xxxu_restore_regs(priv, adda_regs, priv->adda_backup, + RTL8XXXU_ADDA_REGS); + + /* Reload MAC parameters */ + rtl8xxxu_restore_mac_regs(priv, iqk_mac_regs, priv->mac_backup); + + /* Reload BB parameters */ + rtl8xxxu_restore_regs(priv, iqk_bb_regs, + priv->bb_backup, RTL8XXXU_BB_REGS); + + /* Restore RX initial gain */ + val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1); + val32 &= 0xffffff00; + rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | 0x50); + rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | xa_agc); + + if (priv->tx_paths > 1) { + val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1); + val32 &= 0xffffff00; + rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1, + val32 | 0x50); + rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1, + val32 | xb_agc); + } + + /* Load 0xe30 IQC default value */ + rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x01008c00); + rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x01008c00); + } +} + +static void rtl8723bu_phy_iq_calibrate(struct rtl8xxxu_priv *priv) +{ + struct device *dev = &priv->udev->dev; + int result[4][8]; /* last is final result */ + int i, candidate; + bool path_a_ok, path_b_ok; + u32 reg_e94, reg_e9c, reg_ea4, reg_eac; + u32 reg_eb4, reg_ebc, reg_ec4, reg_ecc; + u32 val32, bt_control; + s32 reg_tmp = 0; + bool simu; + + rtl8xxxu_prepare_calibrate(priv, 1); + + memset(result, 0, sizeof(result)); + candidate = -1; + + path_a_ok = false; + path_b_ok = false; + + bt_control = rtl8xxxu_read32(priv, REG_BT_CONTROL_8723BU); + + for (i = 0; i < 3; i++) { + rtl8723bu_phy_iqcalibrate(priv, result, i); + + if (i == 1) { + simu = rtl8xxxu_gen2_simularity_compare(priv, + result, 0, 1); + if (simu) { + candidate = 0; + break; + } + } + + if (i == 2) { + simu = rtl8xxxu_gen2_simularity_compare(priv, + result, 0, 2); + if (simu) { + candidate = 0; + break; + } + + simu = rtl8xxxu_gen2_simularity_compare(priv, + result, 1, 2); + if (simu) { + candidate = 1; + } else { + for (i = 0; i < 8; i++) + reg_tmp += result[3][i]; + + if (reg_tmp) + candidate = 3; + else + candidate = -1; + } + } + } + + for (i = 0; i < 4; i++) { + reg_e94 = result[i][0]; + reg_e9c = result[i][1]; + reg_ea4 = result[i][2]; + reg_eac = result[i][3]; + reg_eb4 = result[i][4]; + reg_ebc = result[i][5]; + reg_ec4 = result[i][6]; + reg_ecc = result[i][7]; + } + + if (candidate >= 0) { + reg_e94 = result[candidate][0]; + priv->rege94 = reg_e94; + reg_e9c = result[candidate][1]; + priv->rege9c = reg_e9c; + reg_ea4 = result[candidate][2]; + reg_eac = result[candidate][3]; + reg_eb4 = result[candidate][4]; + priv->regeb4 = reg_eb4; + reg_ebc = result[candidate][5]; + priv->regebc = reg_ebc; + reg_ec4 = result[candidate][6]; + reg_ecc = result[candidate][7]; + dev_dbg(dev, "%s: candidate is %x\n", __func__, candidate); + dev_dbg(dev, + "%s: e94 =%x e9c=%x ea4=%x eac=%x eb4=%x ebc=%x ec4=%x " + "ecc=%x\n ", __func__, reg_e94, reg_e9c, + reg_ea4, reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc); + path_a_ok = true; + path_b_ok = true; + } else { + reg_e94 = reg_eb4 = priv->rege94 = priv->regeb4 = 0x100; + reg_e9c = reg_ebc = priv->rege9c = priv->regebc = 0x0; + } + + if (reg_e94 && candidate >= 0) + rtl8xxxu_fill_iqk_matrix_a(priv, path_a_ok, result, + candidate, (reg_ea4 == 0)); + + if (priv->tx_paths > 1 && reg_eb4) + rtl8xxxu_fill_iqk_matrix_b(priv, path_b_ok, result, + candidate, (reg_ec4 == 0)); + + rtl8xxxu_save_regs(priv, rtl8xxxu_iqk_phy_iq_bb_reg, + priv->bb_recovery_backup, RTL8XXXU_BB_REGS); + + rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, bt_control); + + val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); + val32 |= 0x80000; + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x18000); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f); + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xe6177); + val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED); + val32 |= 0x20; + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32); + rtl8xxxu_write_rfreg(priv, RF_A, 0x43, 0x300bd); + + if (priv->rf_paths > 1) + dev_dbg(dev, "%s: 8723BU 2T not supported\n", __func__); + + rtl8xxxu_prepare_calibrate(priv, 0); +} + +static int rtl8723bu_active_to_emu(struct rtl8xxxu_priv *priv) +{ + u8 val8; + u16 val16; + u32 val32; + int count, ret = 0; + + /* Turn off RF */ + rtl8xxxu_write8(priv, REG_RF_CTRL, 0); + + /* Enable rising edge triggering interrupt */ + val16 = rtl8xxxu_read16(priv, REG_GPIO_INTM); + val16 &= ~GPIO_INTM_EDGE_TRIG_IRQ; + rtl8xxxu_write16(priv, REG_GPIO_INTM, val16); + + /* Release WLON reset 0x04[16]= 1*/ + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + val32 |= APS_FSMCO_WLON_RESET; + rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); + + /* 0x0005[1] = 1 turn off MAC by HW state machine*/ + val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); + val8 |= BIT(1); + rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); + + for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { + val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); + if ((val8 & BIT(1)) == 0) + break; + udelay(10); + } + + if (!count) { + dev_warn(&priv->udev->dev, "%s: Disabling MAC timed out\n", + __func__); + ret = -EBUSY; + goto exit; + } + + /* Enable BT control XTAL setting */ + val8 = rtl8xxxu_read8(priv, REG_AFE_MISC); + val8 &= ~AFE_MISC_WL_XTAL_CTRL; + rtl8xxxu_write8(priv, REG_AFE_MISC, val8); + + /* 0x0000[5] = 1 analog Ips to digital, 1:isolation */ + val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL); + val8 |= SYS_ISO_ANALOG_IPS; + rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8); + + /* 0x0020[0] = 0 disable LDOA12 MACRO block*/ + val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL); + val8 &= ~LDOA15_ENABLE; + rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8); + +exit: + return ret; +} + +static int rtl8723b_emu_to_active(struct rtl8xxxu_priv *priv) +{ + u8 val8; + u32 val32; + int count, ret = 0; + + /* 0x20[0] = 1 enable LDOA12 MACRO block for all interface */ + val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL); + val8 |= LDOA15_ENABLE; + rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8); + + /* 0x67[0] = 0 to disable BT_GPS_SEL pins*/ + val8 = rtl8xxxu_read8(priv, 0x0067); + val8 &= ~BIT(4); + rtl8xxxu_write8(priv, 0x0067, val8); + + mdelay(1); + + /* 0x00[5] = 0 release analog Ips to digital, 1:isolation */ + val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL); + val8 &= ~SYS_ISO_ANALOG_IPS; + rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8); + + /* Disable SW LPS 0x04[10]= 0 */ + val32 = rtl8xxxu_read8(priv, REG_APS_FSMCO); + val32 &= ~APS_FSMCO_SW_LPS; + rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); + + /* Wait until 0x04[17] = 1 power ready */ + for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + if (val32 & BIT(17)) + break; + + udelay(10); + } + + if (!count) { + ret = -EBUSY; + goto exit; + } + + /* We should be able to optimize the following three entries into one */ + + /* Release WLON reset 0x04[16]= 1*/ + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + val32 |= APS_FSMCO_WLON_RESET; + rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); + + /* Disable HWPDN 0x04[15]= 0*/ + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + val32 &= ~APS_FSMCO_HW_POWERDOWN; + rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); + + /* Disable WL suspend*/ + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + val32 &= ~(APS_FSMCO_HW_SUSPEND | APS_FSMCO_PCIE); + rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); + + /* Set, then poll until 0 */ + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + val32 |= APS_FSMCO_MAC_ENABLE; + rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); + + for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { + val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); + if ((val32 & APS_FSMCO_MAC_ENABLE) == 0) { + ret = 0; + break; + } + udelay(10); + } + + if (!count) { + ret = -EBUSY; + goto exit; + } + + /* Enable WL control XTAL setting */ + val8 = rtl8xxxu_read8(priv, REG_AFE_MISC); + val8 |= AFE_MISC_WL_XTAL_CTRL; + rtl8xxxu_write8(priv, REG_AFE_MISC, val8); + + /* Enable falling edge triggering interrupt */ + val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 1); + val8 |= BIT(1); + rtl8xxxu_write8(priv, REG_GPIO_INTM + 1, val8); + + /* Enable GPIO9 interrupt mode */ + val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2 + 1); + val8 |= BIT(1); + rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2 + 1, val8); + + /* Enable GPIO9 input mode */ + val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2); + val8 &= ~BIT(1); + rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2, val8); + + /* Enable HSISR GPIO[C:0] interrupt */ + val8 = rtl8xxxu_read8(priv, REG_HSIMR); + val8 |= BIT(0); + rtl8xxxu_write8(priv, REG_HSIMR, val8); + + /* Enable HSISR GPIO9 interrupt */ + val8 = rtl8xxxu_read8(priv, REG_HSIMR + 2); + val8 |= BIT(1); + rtl8xxxu_write8(priv, REG_HSIMR + 2, val8); + + val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL); + val8 |= MULTI_WIFI_HW_ROF_EN; + rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL, val8); + + /* For GPIO9 internal pull high setting BIT(14) */ + val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL + 1); + val8 |= BIT(6); + rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL + 1, val8); + +exit: + return ret; +} + +static int rtl8723bu_power_on(struct rtl8xxxu_priv *priv) +{ + u8 val8; + u16 val16; + u32 val32; + int ret; + + rtl8723a_disabled_to_emu(priv); + + ret = rtl8723b_emu_to_active(priv); + if (ret) + goto exit; + + /* + * Enable MAC DMA/WMAC/SCHEDULE/SEC block + * Set CR bit10 to enable 32k calibration. + */ + val16 = rtl8xxxu_read16(priv, REG_CR); + val16 |= (CR_HCI_TXDMA_ENABLE | CR_HCI_RXDMA_ENABLE | + CR_TXDMA_ENABLE | CR_RXDMA_ENABLE | + CR_PROTOCOL_ENABLE | CR_SCHEDULE_ENABLE | + CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE | + CR_SECURITY_ENABLE | CR_CALTIMER_ENABLE); + rtl8xxxu_write16(priv, REG_CR, val16); + + /* + * BT coexist power on settings. This is identical for 1 and 2 + * antenna parts. + */ + rtl8xxxu_write8(priv, REG_PAD_CTRL1 + 3, 0x20); + + val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); + val16 |= SYS_FUNC_BBRSTB | SYS_FUNC_BB_GLB_RSTN; + rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); + + rtl8xxxu_write8(priv, REG_BT_CONTROL_8723BU + 1, 0x18); + rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04); + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00); + /* Antenna inverse */ + rtl8xxxu_write8(priv, 0xfe08, 0x01); + + val16 = rtl8xxxu_read16(priv, REG_PWR_DATA); + val16 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN; + rtl8xxxu_write16(priv, REG_PWR_DATA, val16); + + val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); + val32 |= LEDCFG0_DPDT_SELECT; + rtl8xxxu_write32(priv, REG_LEDCFG0, val32); + + val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1); + val8 &= ~PAD_CTRL1_SW_DPDT_SEL_DATA; + rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8); +exit: + return ret; +} + +static void rtl8723bu_power_off(struct rtl8xxxu_priv *priv) +{ + u8 val8; + u16 val16; + + rtl8xxxu_flush_fifo(priv); + + /* + * Disable TX report timer + */ + val8 = rtl8xxxu_read8(priv, REG_TX_REPORT_CTRL); + val8 &= ~TX_REPORT_CTRL_TIMER_ENABLE; + rtl8xxxu_write8(priv, REG_TX_REPORT_CTRL, val8); + + rtl8xxxu_write8(priv, REG_CR, 0x0000); + + rtl8xxxu_active_to_lps(priv); + + /* Reset Firmware if running in RAM */ + if (rtl8xxxu_read8(priv, REG_MCU_FW_DL) & MCU_FW_RAM_SEL) + rtl8xxxu_firmware_self_reset(priv); + + /* Reset MCU */ + val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); + val16 &= ~SYS_FUNC_CPU_ENABLE; + rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); + + /* Reset MCU ready status */ + rtl8xxxu_write8(priv, REG_MCU_FW_DL, 0x00); + + rtl8723bu_active_to_emu(priv); + + val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); + val8 |= BIT(3); /* APS_FSMCO_HW_SUSPEND */ + rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); + + /* 0x48[16] = 1 to enable GPIO9 as EXT wakeup */ + val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 2); + val8 |= BIT(0); + rtl8xxxu_write8(priv, REG_GPIO_INTM + 2, val8); +} + +static void rtl8723b_enable_rf(struct rtl8xxxu_priv *priv) +{ + struct h2c_cmd h2c; + u32 val32; + u8 val8; + + /* + * No indication anywhere as to what 0x0790 does. The 2 antenna + * vendor code preserves bits 6-7 here. + */ + rtl8xxxu_write8(priv, 0x0790, 0x05); + /* + * 0x0778 seems to be related to enabling the number of antennas + * In the vendor driver halbtc8723b2ant_InitHwConfig() sets it + * to 0x03, while halbtc8723b1ant_InitHwConfig() sets it to 0x01 + */ + rtl8xxxu_write8(priv, 0x0778, 0x01); + + val8 = rtl8xxxu_read8(priv, REG_GPIO_MUXCFG); + val8 |= BIT(5); + rtl8xxxu_write8(priv, REG_GPIO_MUXCFG, val8); + + rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_IQADJ_G1, 0x780); + + rtl8723bu_write_btreg(priv, 0x3c, 0x15); /* BT TRx Mask on */ + + /* + * Set BT grant to low + */ + memset(&h2c, 0, sizeof(struct h2c_cmd)); + h2c.bt_grant.cmd = H2C_8723B_BT_GRANT; + h2c.bt_grant.data = 0; + rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_grant)); + + /* + * WLAN action by PTA + */ + rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04); + + /* + * BT select S0/S1 controlled by WiFi + */ + val8 = rtl8xxxu_read8(priv, 0x0067); + val8 |= BIT(5); + rtl8xxxu_write8(priv, 0x0067, val8); + + val32 = rtl8xxxu_read32(priv, REG_PWR_DATA); + val32 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN; + rtl8xxxu_write32(priv, REG_PWR_DATA, val32); + + /* + * Bits 6/7 are marked in/out ... but for what? + */ + rtl8xxxu_write8(priv, 0x0974, 0xff); + + val32 = rtl8xxxu_read32(priv, REG_RFE_BUFFER); + val32 |= (BIT(0) | BIT(1)); + rtl8xxxu_write32(priv, REG_RFE_BUFFER, val32); + + rtl8xxxu_write8(priv, REG_RFE_CTRL_ANTA_SRC, 0x77); + + val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); + val32 &= ~BIT(24); + val32 |= BIT(23); + rtl8xxxu_write32(priv, REG_LEDCFG0, val32); + + /* + * Fix external switch Main->S1, Aux->S0 + */ + val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1); + val8 &= ~BIT(0); + rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8); + + memset(&h2c, 0, sizeof(struct h2c_cmd)); + h2c.ant_sel_rsv.cmd = H2C_8723B_ANT_SEL_RSV; + h2c.ant_sel_rsv.ant_inverse = 1; + h2c.ant_sel_rsv.int_switch_type = 0; + rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.ant_sel_rsv)); + + /* + * 0x280, 0x00, 0x200, 0x80 - not clear + */ + rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00); + + /* + * Software control, antenna at WiFi side + */ +#ifdef NEED_PS_TDMA + rtl8723bu_set_ps_tdma(priv, 0x08, 0x00, 0x00, 0x00, 0x00); +#endif + + rtl8xxxu_write32(priv, REG_BT_COEX_TABLE1, 0x55555555); + rtl8xxxu_write32(priv, REG_BT_COEX_TABLE2, 0x55555555); + rtl8xxxu_write32(priv, REG_BT_COEX_TABLE3, 0x00ffffff); + rtl8xxxu_write8(priv, REG_BT_COEX_TABLE4, 0x03); + + memset(&h2c, 0, sizeof(struct h2c_cmd)); + h2c.bt_info.cmd = H2C_8723B_BT_INFO; + h2c.bt_info.data = BIT(0); + rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_info)); + + memset(&h2c, 0, sizeof(struct h2c_cmd)); + h2c.ignore_wlan.cmd = H2C_8723B_BT_IGNORE_WLANACT; + h2c.ignore_wlan.data = 0; + rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.ignore_wlan)); +} + +static void rtl8723bu_init_aggregation(struct rtl8xxxu_priv *priv) +{ + u32 agg_rx; + u8 agg_ctrl; + + /* + * For now simply disable RX aggregation + */ + agg_ctrl = rtl8xxxu_read8(priv, REG_TRXDMA_CTRL); + agg_ctrl &= ~TRXDMA_CTRL_RXDMA_AGG_EN; + + agg_rx = rtl8xxxu_read32(priv, REG_RXDMA_AGG_PG_TH); + agg_rx &= ~RXDMA_USB_AGG_ENABLE; + agg_rx &= ~0xff0f; + + rtl8xxxu_write8(priv, REG_TRXDMA_CTRL, agg_ctrl); + rtl8xxxu_write32(priv, REG_RXDMA_AGG_PG_TH, agg_rx); +} + +static void rtl8723bu_init_statistics(struct rtl8xxxu_priv *priv) +{ + u32 val32; + + /* Time duration for NHM unit: 4us, 0x2710=40ms */ + rtl8xxxu_write16(priv, REG_NHM_TIMER_8723B + 2, 0x2710); + rtl8xxxu_write16(priv, REG_NHM_TH9_TH10_8723B + 2, 0xffff); + rtl8xxxu_write32(priv, REG_NHM_TH3_TO_TH0_8723B, 0xffffff52); + rtl8xxxu_write32(priv, REG_NHM_TH7_TO_TH4_8723B, 0xffffffff); + /* TH8 */ + val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); + val32 |= 0xff; + rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); + /* Enable CCK */ + val32 = rtl8xxxu_read32(priv, REG_NHM_TH9_TH10_8723B); + val32 |= BIT(8) | BIT(9) | BIT(10); + rtl8xxxu_write32(priv, REG_NHM_TH9_TH10_8723B, val32); + /* Max power amongst all RX antennas */ + val32 = rtl8xxxu_read32(priv, REG_OFDM0_FA_RSTC); + val32 |= BIT(7); + rtl8xxxu_write32(priv, REG_OFDM0_FA_RSTC, val32); +} + +struct rtl8xxxu_fileops rtl8723bu_fops = { + .parse_efuse = rtl8723bu_parse_efuse, + .load_firmware = rtl8723bu_load_firmware, + .power_on = rtl8723bu_power_on, + .power_off = rtl8723bu_power_off, + .reset_8051 = rtl8723bu_reset_8051, + .llt_init = rtl8xxxu_auto_llt_table, + .init_phy_bb = rtl8723bu_init_phy_bb, + .init_phy_rf = rtl8723bu_init_phy_rf, + .phy_init_antenna_selection = rtl8723bu_phy_init_antenna_selection, + .phy_iq_calibrate = rtl8723bu_phy_iq_calibrate, + .config_channel = rtl8xxxu_gen2_config_channel, + .parse_rx_desc = rtl8xxxu_parse_rxdesc24, + .init_aggregation = rtl8723bu_init_aggregation, + .init_statistics = rtl8723bu_init_statistics, + .enable_rf = rtl8723b_enable_rf, + .disable_rf = rtl8xxxu_gen2_disable_rf, + .usb_quirks = rtl8xxxu_gen2_usb_quirks, + .set_tx_power = rtl8723b_set_tx_power, + .update_rate_mask = rtl8xxxu_gen2_update_rate_mask, + .report_connect = rtl8xxxu_gen2_report_connect, + .writeN_block_size = 1024, + .mbox_ext_reg = REG_HMBOX_EXT0_8723B, + .mbox_ext_width = 4, + .tx_desc_size = sizeof(struct rtl8xxxu_txdesc40), + .rx_desc_size = sizeof(struct rtl8xxxu_rxdesc24), + .has_s0s1 = 1, + .adda_1t_init = 0x01c00014, + .adda_1t_path_on = 0x01c00014, + .adda_2t_path_on_a = 0x01c00014, + .adda_2t_path_on_b = 0x01c00014, + .trxff_boundary = 0x3f7f, + .pbp_rx = PBP_PAGE_SIZE_256, + .pbp_tx = PBP_PAGE_SIZE_256, + .mactable = rtl8723b_mac_init_table, +}; diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c index d97de86d88df..5542a41f4d27 100644 --- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c +++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c @@ -153,37 +153,6 @@ static struct rtl8xxxu_reg8val rtl8xxxu_gen1_mac_init_table[] = { {0x70a, 0x65}, {0x70b, 0x87}, {0xffff, 0xff}, }; -static struct rtl8xxxu_reg8val rtl8723b_mac_init_table[] = { - {0x02f, 0x30}, {0x035, 0x00}, {0x039, 0x08}, {0x04e, 0xe0}, - {0x064, 0x00}, {0x067, 0x20}, {0x428, 0x0a}, {0x429, 0x10}, - {0x430, 0x00}, {0x431, 0x00}, - {0x432, 0x00}, {0x433, 0x01}, {0x434, 0x04}, {0x435, 0x05}, - {0x436, 0x07}, {0x437, 0x08}, {0x43c, 0x04}, {0x43d, 0x05}, - {0x43e, 0x07}, {0x43f, 0x08}, {0x440, 0x5d}, {0x441, 0x01}, - {0x442, 0x00}, {0x444, 0x10}, {0x445, 0x00}, {0x446, 0x00}, - {0x447, 0x00}, {0x448, 0x00}, {0x449, 0xf0}, {0x44a, 0x0f}, - {0x44b, 0x3e}, {0x44c, 0x10}, {0x44d, 0x00}, {0x44e, 0x00}, - {0x44f, 0x00}, {0x450, 0x00}, {0x451, 0xf0}, {0x452, 0x0f}, - {0x453, 0x00}, {0x456, 0x5e}, {0x460, 0x66}, {0x461, 0x66}, - {0x4c8, 0xff}, {0x4c9, 0x08}, {0x4cc, 0xff}, - {0x4cd, 0xff}, {0x4ce, 0x01}, {0x500, 0x26}, {0x501, 0xa2}, - {0x502, 0x2f}, {0x503, 0x00}, {0x504, 0x28}, {0x505, 0xa3}, - {0x506, 0x5e}, {0x507, 0x00}, {0x508, 0x2b}, {0x509, 0xa4}, - {0x50a, 0x5e}, {0x50b, 0x00}, {0x50c, 0x4f}, {0x50d, 0xa4}, - {0x50e, 0x00}, {0x50f, 0x00}, {0x512, 0x1c}, {0x514, 0x0a}, - {0x516, 0x0a}, {0x525, 0x4f}, - {0x550, 0x10}, {0x551, 0x10}, {0x559, 0x02}, {0x55c, 0x50}, - {0x55d, 0xff}, {0x605, 0x30}, {0x608, 0x0e}, {0x609, 0x2a}, - {0x620, 0xff}, {0x621, 0xff}, {0x622, 0xff}, {0x623, 0xff}, - {0x624, 0xff}, {0x625, 0xff}, {0x626, 0xff}, {0x627, 0xff}, - {0x638, 0x50}, {0x63c, 0x0a}, {0x63d, 0x0a}, {0x63e, 0x0e}, - {0x63f, 0x0e}, {0x640, 0x40}, {0x642, 0x40}, {0x643, 0x00}, - {0x652, 0xc8}, {0x66e, 0x05}, {0x700, 0x21}, {0x701, 0x43}, - {0x702, 0x65}, {0x703, 0x87}, {0x708, 0x21}, {0x709, 0x43}, - {0x70a, 0x65}, {0x70b, 0x87}, {0x765, 0x18}, {0x76e, 0x04}, - {0xffff, 0xff}, -}; - #ifdef CONFIG_RTL8XXXU_UNTESTED static struct rtl8xxxu_power_base rtl8188r_power_base = { .reg_0e00 = 0x06080808, @@ -350,107 +319,6 @@ static struct rtl8xxxu_reg32val rtl8723a_phy_1t_init_table[] = { {0xffff, 0xffffffff}, }; -static struct rtl8xxxu_reg32val rtl8723b_phy_1t_init_table[] = { - {0x800, 0x80040000}, {0x804, 0x00000003}, - {0x808, 0x0000fc00}, {0x80c, 0x0000000a}, - {0x810, 0x10001331}, {0x814, 0x020c3d10}, - {0x818, 0x02200385}, {0x81c, 0x00000000}, - {0x820, 0x01000100}, {0x824, 0x00190204}, - {0x828, 0x00000000}, {0x82c, 0x00000000}, - {0x830, 0x00000000}, {0x834, 0x00000000}, - {0x838, 0x00000000}, {0x83c, 0x00000000}, - {0x840, 0x00010000}, {0x844, 0x00000000}, - {0x848, 0x00000000}, {0x84c, 0x00000000}, - {0x850, 0x00000000}, {0x854, 0x00000000}, - {0x858, 0x569a11a9}, {0x85c, 0x01000014}, - {0x860, 0x66f60110}, {0x864, 0x061f0649}, - {0x868, 0x00000000}, {0x86c, 0x27272700}, - {0x870, 0x07000760}, {0x874, 0x25004000}, - {0x878, 0x00000808}, {0x87c, 0x00000000}, - {0x880, 0xb0000c1c}, {0x884, 0x00000001}, - {0x888, 0x00000000}, {0x88c, 0xccc000c0}, - {0x890, 0x00000800}, {0x894, 0xfffffffe}, - {0x898, 0x40302010}, {0x89c, 0x00706050}, - {0x900, 0x00000000}, {0x904, 0x00000023}, - {0x908, 0x00000000}, {0x90c, 0x81121111}, - {0x910, 0x00000002}, {0x914, 0x00000201}, - {0xa00, 0x00d047c8}, {0xa04, 0x80ff800c}, - {0xa08, 0x8c838300}, {0xa0c, 0x2e7f120f}, - {0xa10, 0x9500bb78}, {0xa14, 0x1114d028}, - {0xa18, 0x00881117}, {0xa1c, 0x89140f00}, - {0xa20, 0x1a1b0000}, {0xa24, 0x090e1317}, - {0xa28, 0x00000204}, {0xa2c, 0x00d30000}, - {0xa70, 0x101fbf00}, {0xa74, 0x00000007}, - {0xa78, 0x00000900}, {0xa7c, 0x225b0606}, - {0xa80, 0x21806490}, {0xb2c, 0x00000000}, - {0xc00, 0x48071d40}, {0xc04, 0x03a05611}, - {0xc08, 0x000000e4}, {0xc0c, 0x6c6c6c6c}, - {0xc10, 0x08800000}, {0xc14, 0x40000100}, - {0xc18, 0x08800000}, {0xc1c, 0x40000100}, - {0xc20, 0x00000000}, {0xc24, 0x00000000}, - {0xc28, 0x00000000}, {0xc2c, 0x00000000}, - {0xc30, 0x69e9ac44}, {0xc34, 0x469652af}, - {0xc38, 0x49795994}, {0xc3c, 0x0a97971c}, - {0xc40, 0x1f7c403f}, {0xc44, 0x000100b7}, - {0xc48, 0xec020107}, {0xc4c, 0x007f037f}, - {0xc50, 0x69553420}, {0xc54, 0x43bc0094}, - {0xc58, 0x00013149}, {0xc5c, 0x00250492}, - {0xc60, 0x00000000}, {0xc64, 0x7112848b}, - {0xc68, 0x47c00bff}, {0xc6c, 0x00000036}, - {0xc70, 0x2c7f000d}, {0xc74, 0x020610db}, - {0xc78, 0x0000001f}, {0xc7c, 0x00b91612}, - {0xc80, 0x390000e4}, {0xc84, 0x20f60000}, - {0xc88, 0x40000100}, {0xc8c, 0x20200000}, - {0xc90, 0x00020e1a}, {0xc94, 0x00000000}, - {0xc98, 0x00020e1a}, {0xc9c, 0x00007f7f}, - {0xca0, 0x00000000}, {0xca4, 0x000300a0}, - {0xca8, 0x00000000}, {0xcac, 0x00000000}, - {0xcb0, 0x00000000}, {0xcb4, 0x00000000}, - {0xcb8, 0x00000000}, {0xcbc, 0x28000000}, - {0xcc0, 0x00000000}, {0xcc4, 0x00000000}, - {0xcc8, 0x00000000}, {0xccc, 0x00000000}, - {0xcd0, 0x00000000}, {0xcd4, 0x00000000}, - {0xcd8, 0x64b22427}, {0xcdc, 0x00766932}, - {0xce0, 0x00222222}, {0xce4, 0x00000000}, - {0xce8, 0x37644302}, {0xcec, 0x2f97d40c}, - {0xd00, 0x00000740}, {0xd04, 0x40020401}, - {0xd08, 0x0000907f}, {0xd0c, 0x20010201}, - {0xd10, 0xa0633333}, {0xd14, 0x3333bc53}, - {0xd18, 0x7a8f5b6f}, {0xd2c, 0xcc979975}, - {0xd30, 0x00000000}, {0xd34, 0x80608000}, - {0xd38, 0x00000000}, {0xd3c, 0x00127353}, - {0xd40, 0x00000000}, {0xd44, 0x00000000}, - {0xd48, 0x00000000}, {0xd4c, 0x00000000}, - {0xd50, 0x6437140a}, {0xd54, 0x00000000}, - {0xd58, 0x00000282}, {0xd5c, 0x30032064}, - {0xd60, 0x4653de68}, {0xd64, 0x04518a3c}, - {0xd68, 0x00002101}, {0xd6c, 0x2a201c16}, - {0xd70, 0x1812362e}, {0xd74, 0x322c2220}, - {0xd78, 0x000e3c24}, {0xe00, 0x2d2d2d2d}, - {0xe04, 0x2d2d2d2d}, {0xe08, 0x0390272d}, - {0xe10, 0x2d2d2d2d}, {0xe14, 0x2d2d2d2d}, - {0xe18, 0x2d2d2d2d}, {0xe1c, 0x2d2d2d2d}, - {0xe28, 0x00000000}, {0xe30, 0x1000dc1f}, - {0xe34, 0x10008c1f}, {0xe38, 0x02140102}, - {0xe3c, 0x681604c2}, {0xe40, 0x01007c00}, - {0xe44, 0x01004800}, {0xe48, 0xfb000000}, - {0xe4c, 0x000028d1}, {0xe50, 0x1000dc1f}, - {0xe54, 0x10008c1f}, {0xe58, 0x02140102}, - {0xe5c, 0x28160d05}, {0xe60, 0x00000008}, - {0xe68, 0x001b2556}, {0xe6c, 0x00c00096}, - {0xe70, 0x00c00096}, {0xe74, 0x01000056}, - {0xe78, 0x01000014}, {0xe7c, 0x01000056}, - {0xe80, 0x01000014}, {0xe84, 0x00c00096}, - {0xe88, 0x01000056}, {0xe8c, 0x00c00096}, - {0xed0, 0x00c00096}, {0xed4, 0x00c00096}, - {0xed8, 0x00c00096}, {0xedc, 0x000000d6}, - {0xee0, 0x000000d6}, {0xeec, 0x01c00016}, - {0xf14, 0x00000003}, {0xf4c, 0x00000000}, - {0xf00, 0x00000300}, - {0x820, 0x01000100}, {0x800, 0x83040000}, - {0xffff, 0xffffffff}, -}; - static struct rtl8xxxu_reg32val rtl8192cu_phy_2t_init_table[] = { {0x024, 0x0011800f}, {0x028, 0x00ffdb83}, {0x800, 0x80040002}, {0x804, 0x00000003}, @@ -816,77 +684,6 @@ static struct rtl8xxxu_reg32val rtl8xxx_agc_highpa_table[] = { {0xffff, 0xffffffff} }; -static struct rtl8xxxu_reg32val rtl8xxx_agc_8723bu_table[] = { - {0xc78, 0xfd000001}, {0xc78, 0xfc010001}, - {0xc78, 0xfb020001}, {0xc78, 0xfa030001}, - {0xc78, 0xf9040001}, {0xc78, 0xf8050001}, - {0xc78, 0xf7060001}, {0xc78, 0xf6070001}, - {0xc78, 0xf5080001}, {0xc78, 0xf4090001}, - {0xc78, 0xf30a0001}, {0xc78, 0xf20b0001}, - {0xc78, 0xf10c0001}, {0xc78, 0xf00d0001}, - {0xc78, 0xef0e0001}, {0xc78, 0xee0f0001}, - {0xc78, 0xed100001}, {0xc78, 0xec110001}, - {0xc78, 0xeb120001}, {0xc78, 0xea130001}, - {0xc78, 0xe9140001}, {0xc78, 0xe8150001}, - {0xc78, 0xe7160001}, {0xc78, 0xe6170001}, - {0xc78, 0xe5180001}, {0xc78, 0xe4190001}, - {0xc78, 0xe31a0001}, {0xc78, 0xa51b0001}, - {0xc78, 0xa41c0001}, {0xc78, 0xa31d0001}, - {0xc78, 0x671e0001}, {0xc78, 0x661f0001}, - {0xc78, 0x65200001}, {0xc78, 0x64210001}, - {0xc78, 0x63220001}, {0xc78, 0x4a230001}, - {0xc78, 0x49240001}, {0xc78, 0x48250001}, - {0xc78, 0x47260001}, {0xc78, 0x46270001}, - {0xc78, 0x45280001}, {0xc78, 0x44290001}, - {0xc78, 0x432a0001}, {0xc78, 0x422b0001}, - {0xc78, 0x292c0001}, {0xc78, 0x282d0001}, - {0xc78, 0x272e0001}, {0xc78, 0x262f0001}, - {0xc78, 0x0a300001}, {0xc78, 0x09310001}, - {0xc78, 0x08320001}, {0xc78, 0x07330001}, - {0xc78, 0x06340001}, {0xc78, 0x05350001}, - {0xc78, 0x04360001}, {0xc78, 0x03370001}, - {0xc78, 0x02380001}, {0xc78, 0x01390001}, - {0xc78, 0x013a0001}, {0xc78, 0x013b0001}, - {0xc78, 0x013c0001}, {0xc78, 0x013d0001}, - {0xc78, 0x013e0001}, {0xc78, 0x013f0001}, - {0xc78, 0xfc400001}, {0xc78, 0xfb410001}, - {0xc78, 0xfa420001}, {0xc78, 0xf9430001}, - {0xc78, 0xf8440001}, {0xc78, 0xf7450001}, - {0xc78, 0xf6460001}, {0xc78, 0xf5470001}, - {0xc78, 0xf4480001}, {0xc78, 0xf3490001}, - {0xc78, 0xf24a0001}, {0xc78, 0xf14b0001}, - {0xc78, 0xf04c0001}, {0xc78, 0xef4d0001}, - {0xc78, 0xee4e0001}, {0xc78, 0xed4f0001}, - {0xc78, 0xec500001}, {0xc78, 0xeb510001}, - {0xc78, 0xea520001}, {0xc78, 0xe9530001}, - {0xc78, 0xe8540001}, {0xc78, 0xe7550001}, - {0xc78, 0xe6560001}, {0xc78, 0xe5570001}, - {0xc78, 0xe4580001}, {0xc78, 0xe3590001}, - {0xc78, 0xa65a0001}, {0xc78, 0xa55b0001}, - {0xc78, 0xa45c0001}, {0xc78, 0xa35d0001}, - {0xc78, 0x675e0001}, {0xc78, 0x665f0001}, - {0xc78, 0x65600001}, {0xc78, 0x64610001}, - {0xc78, 0x63620001}, {0xc78, 0x62630001}, - {0xc78, 0x61640001}, {0xc78, 0x48650001}, - {0xc78, 0x47660001}, {0xc78, 0x46670001}, - {0xc78, 0x45680001}, {0xc78, 0x44690001}, - {0xc78, 0x436a0001}, {0xc78, 0x426b0001}, - {0xc78, 0x286c0001}, {0xc78, 0x276d0001}, - {0xc78, 0x266e0001}, {0xc78, 0x256f0001}, - {0xc78, 0x24700001}, {0xc78, 0x09710001}, - {0xc78, 0x08720001}, {0xc78, 0x07730001}, - {0xc78, 0x06740001}, {0xc78, 0x05750001}, - {0xc78, 0x04760001}, {0xc78, 0x03770001}, - {0xc78, 0x02780001}, {0xc78, 0x01790001}, - {0xc78, 0x017a0001}, {0xc78, 0x017b0001}, - {0xc78, 0x017c0001}, {0xc78, 0x017d0001}, - {0xc78, 0x017e0001}, {0xc78, 0x017f0001}, - {0xc50, 0x69553422}, - {0xc50, 0x69553420}, - {0x824, 0x00390204}, - {0xffff, 0xffffffff} -}; - static struct rtl8xxxu_rfregval rtl8723au_radioa_1t_init_table[] = { {0x00, 0x00030159}, {0x01, 0x00031284}, {0x02, 0x00098000}, {0x03, 0x00039c63}, @@ -962,75 +759,6 @@ static struct rtl8xxxu_rfregval rtl8723au_radioa_1t_init_table[] = { {0xff, 0xffffffff} }; -static struct rtl8xxxu_rfregval rtl8723bu_radioa_1t_init_table[] = { - {0x00, 0x00010000}, {0xb0, 0x000dffe0}, - {0xfe, 0x00000000}, {0xfe, 0x00000000}, - {0xfe, 0x00000000}, {0xb1, 0x00000018}, - {0xfe, 0x00000000}, {0xfe, 0x00000000}, - {0xfe, 0x00000000}, {0xb2, 0x00084c00}, - {0xb5, 0x0000d2cc}, {0xb6, 0x000925aa}, - {0xb7, 0x00000010}, {0xb8, 0x0000907f}, - {0x5c, 0x00000002}, {0x7c, 0x00000002}, - {0x7e, 0x00000005}, {0x8b, 0x0006fc00}, - {0xb0, 0x000ff9f0}, {0x1c, 0x000739d2}, - {0x1e, 0x00000000}, {0xdf, 0x00000780}, - {0x50, 0x00067435}, - /* - * The 8723bu vendor driver indicates that bit 8 should be set in - * 0x51 for package types TFBGA90, TFBGA80, and TFBGA79. However - * they never actually check the package type - and just default - * to not setting it. - */ - {0x51, 0x0006b04e}, - {0x52, 0x000007d2}, {0x53, 0x00000000}, - {0x54, 0x00050400}, {0x55, 0x0004026e}, - {0xdd, 0x0000004c}, {0x70, 0x00067435}, - /* - * 0x71 has same package type condition as for register 0x51 - */ - {0x71, 0x0006b04e}, - {0x72, 0x000007d2}, {0x73, 0x00000000}, - {0x74, 0x00050400}, {0x75, 0x0004026e}, - {0xef, 0x00000100}, {0x34, 0x0000add7}, - {0x35, 0x00005c00}, {0x34, 0x00009dd4}, - {0x35, 0x00005000}, {0x34, 0x00008dd1}, - {0x35, 0x00004400}, {0x34, 0x00007dce}, - {0x35, 0x00003800}, {0x34, 0x00006cd1}, - {0x35, 0x00004400}, {0x34, 0x00005cce}, - {0x35, 0x00003800}, {0x34, 0x000048ce}, - {0x35, 0x00004400}, {0x34, 0x000034ce}, - {0x35, 0x00003800}, {0x34, 0x00002451}, - {0x35, 0x00004400}, {0x34, 0x0000144e}, - {0x35, 0x00003800}, {0x34, 0x00000051}, - {0x35, 0x00004400}, {0xef, 0x00000000}, - {0xef, 0x00000100}, {0xed, 0x00000010}, - {0x44, 0x0000add7}, {0x44, 0x00009dd4}, - {0x44, 0x00008dd1}, {0x44, 0x00007dce}, - {0x44, 0x00006cc1}, {0x44, 0x00005cce}, - {0x44, 0x000044d1}, {0x44, 0x000034ce}, - {0x44, 0x00002451}, {0x44, 0x0000144e}, - {0x44, 0x00000051}, {0xef, 0x00000000}, - {0xed, 0x00000000}, {0x7f, 0x00020080}, - {0xef, 0x00002000}, {0x3b, 0x000380ef}, - {0x3b, 0x000302fe}, {0x3b, 0x00028ce6}, - {0x3b, 0x000200bc}, {0x3b, 0x000188a5}, - {0x3b, 0x00010fbc}, {0x3b, 0x00008f71}, - {0x3b, 0x00000900}, {0xef, 0x00000000}, - {0xed, 0x00000001}, {0x40, 0x000380ef}, - {0x40, 0x000302fe}, {0x40, 0x00028ce6}, - {0x40, 0x000200bc}, {0x40, 0x000188a5}, - {0x40, 0x00010fbc}, {0x40, 0x00008f71}, - {0x40, 0x00000900}, {0xed, 0x00000000}, - {0x82, 0x00080000}, {0x83, 0x00008000}, - {0x84, 0x00048d80}, {0x85, 0x00068000}, - {0xa2, 0x00080000}, {0xa3, 0x00008000}, - {0xa4, 0x00048d80}, {0xa5, 0x00068000}, - {0xed, 0x00000002}, {0xef, 0x00000002}, - {0x56, 0x00000032}, {0x76, 0x00000032}, - {0x01, 0x00000780}, - {0xff, 0xffffffff} -}; - #ifdef CONFIG_RTL8XXXU_UNTESTED static struct rtl8xxxu_rfregval rtl8192cu_radioa_2t_init_table[] = { {0x00, 0x00030159}, {0x01, 0x00031284}, @@ -1553,8 +1281,7 @@ int rtl8xxxu_write_rfreg(struct rtl8xxxu_priv *priv, return retval; } -static int rtl8723a_h2c_cmd(struct rtl8xxxu_priv *priv, - struct h2c_cmd *h2c, int len) +int rtl8723a_h2c_cmd(struct rtl8xxxu_priv *priv, struct h2c_cmd *h2c, int len) { struct device *dev = &priv->udev->dev; int mbox_nr, retry, retval = 0; @@ -1613,27 +1340,6 @@ error: return retval; } -static void rtl8723bu_write_btreg(struct rtl8xxxu_priv *priv, u8 reg, u8 data) -{ - struct h2c_cmd h2c; - int reqnum = 0; - - memset(&h2c, 0, sizeof(struct h2c_cmd)); - h2c.bt_mp_oper.cmd = H2C_8723B_BT_MP_OPER; - h2c.bt_mp_oper.operreq = 0 | (reqnum << 4); - h2c.bt_mp_oper.opcode = BT_MP_OP_WRITE_REG_VALUE; - h2c.bt_mp_oper.data = data; - rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_mp_oper)); - - reqnum++; - memset(&h2c, 0, sizeof(struct h2c_cmd)); - h2c.bt_mp_oper.cmd = H2C_8723B_BT_MP_OPER; - h2c.bt_mp_oper.operreq = 0 | (reqnum << 4); - h2c.bt_mp_oper.opcode = BT_MP_OP_WRITE_REG_VALUE; - h2c.bt_mp_oper.addr = reg; - rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_mp_oper)); -} - static void rtl8xxxu_gen1_enable_rf(struct rtl8xxxu_priv *priv) { u8 val8; @@ -2163,45 +1869,6 @@ rtl8xxxu_gen1_set_tx_power(struct rtl8xxxu_priv *priv, int channel, bool ht40) } } -static void -rtl8723b_set_tx_power(struct rtl8xxxu_priv *priv, int channel, bool ht40) -{ - u32 val32, ofdm, mcs; - u8 cck, ofdmbase, mcsbase; - int group, tx_idx; - - tx_idx = 0; - group = rtl8xxxu_gen2_channel_to_group(channel); - - cck = priv->cck_tx_power_index_B[group]; - val32 = rtl8xxxu_read32(priv, REG_TX_AGC_A_CCK1_MCS32); - val32 &= 0xffff00ff; - val32 |= (cck << 8); - rtl8xxxu_write32(priv, REG_TX_AGC_A_CCK1_MCS32, val32); - - val32 = rtl8xxxu_read32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11); - val32 &= 0xff; - val32 |= ((cck << 8) | (cck << 16) | (cck << 24)); - rtl8xxxu_write32(priv, REG_TX_AGC_B_CCK11_A_CCK2_11, val32); - - ofdmbase = priv->ht40_1s_tx_power_index_B[group]; - ofdmbase += priv->ofdm_tx_power_diff[tx_idx].b; - ofdm = ofdmbase | ofdmbase << 8 | ofdmbase << 16 | ofdmbase << 24; - - rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE18_06, ofdm); - rtl8xxxu_write32(priv, REG_TX_AGC_A_RATE54_24, ofdm); - - mcsbase = priv->ht40_1s_tx_power_index_B[group]; - if (ht40) - mcsbase += priv->ht40_tx_power_diff[tx_idx++].b; - else - mcsbase += priv->ht20_tx_power_diff[tx_idx++].b; - mcs = mcsbase | mcsbase << 8 | mcsbase << 16 | mcsbase << 24; - - rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS03_MCS00, mcs); - rtl8xxxu_write32(priv, REG_TX_AGC_A_MCS07_MCS04, mcs); -} - static void rtl8xxxu_set_linktype(struct rtl8xxxu_priv *priv, enum nl80211_iftype linktype) { @@ -2494,83 +2161,6 @@ static int rtl8723au_parse_efuse(struct rtl8xxxu_priv *priv) return 0; } -static int rtl8723bu_parse_efuse(struct rtl8xxxu_priv *priv) -{ - struct rtl8723bu_efuse *efuse = &priv->efuse_wifi.efuse8723bu; - int i; - - if (efuse->rtl_id != cpu_to_le16(0x8129)) - return -EINVAL; - - ether_addr_copy(priv->mac_addr, efuse->mac_addr); - - memcpy(priv->cck_tx_power_index_A, efuse->tx_power_index_A.cck_base, - sizeof(efuse->tx_power_index_A.cck_base)); - memcpy(priv->cck_tx_power_index_B, efuse->tx_power_index_B.cck_base, - sizeof(efuse->tx_power_index_B.cck_base)); - - memcpy(priv->ht40_1s_tx_power_index_A, - efuse->tx_power_index_A.ht40_base, - sizeof(efuse->tx_power_index_A.ht40_base)); - memcpy(priv->ht40_1s_tx_power_index_B, - efuse->tx_power_index_B.ht40_base, - sizeof(efuse->tx_power_index_B.ht40_base)); - - priv->ofdm_tx_power_diff[0].a = - efuse->tx_power_index_A.ht20_ofdm_1s_diff.a; - priv->ofdm_tx_power_diff[0].b = - efuse->tx_power_index_B.ht20_ofdm_1s_diff.a; - - priv->ht20_tx_power_diff[0].a = - efuse->tx_power_index_A.ht20_ofdm_1s_diff.b; - priv->ht20_tx_power_diff[0].b = - efuse->tx_power_index_B.ht20_ofdm_1s_diff.b; - - priv->ht40_tx_power_diff[0].a = 0; - priv->ht40_tx_power_diff[0].b = 0; - - for (i = 1; i < RTL8723B_TX_COUNT; i++) { - priv->ofdm_tx_power_diff[i].a = - efuse->tx_power_index_A.pwr_diff[i - 1].ofdm; - priv->ofdm_tx_power_diff[i].b = - efuse->tx_power_index_B.pwr_diff[i - 1].ofdm; - - priv->ht20_tx_power_diff[i].a = - efuse->tx_power_index_A.pwr_diff[i - 1].ht20; - priv->ht20_tx_power_diff[i].b = - efuse->tx_power_index_B.pwr_diff[i - 1].ht20; - - priv->ht40_tx_power_diff[i].a = - efuse->tx_power_index_A.pwr_diff[i - 1].ht40; - priv->ht40_tx_power_diff[i].b = - efuse->tx_power_index_B.pwr_diff[i - 1].ht40; - } - - priv->has_xtalk = 1; - priv->xtalk = priv->efuse_wifi.efuse8723bu.xtal_k & 0x3f; - - dev_info(&priv->udev->dev, "Vendor: %.7s\n", efuse->vendor_name); - dev_info(&priv->udev->dev, "Product: %.41s\n", efuse->device_name); - - if (rtl8xxxu_debug & RTL8XXXU_DEBUG_EFUSE) { - int i; - unsigned char *raw = priv->efuse_wifi.raw; - - dev_info(&priv->udev->dev, - "%s: dumping efuse (0x%02zx bytes):\n", - __func__, sizeof(struct rtl8723bu_efuse)); - for (i = 0; i < sizeof(struct rtl8723bu_efuse); i += 8) { - dev_info(&priv->udev->dev, "%02x: " - "%02x %02x %02x %02x %02x %02x %02x %02x\n", i, - raw[i], raw[i + 1], raw[i + 2], - raw[i + 3], raw[i + 4], raw[i + 5], - raw[i + 6], raw[i + 7]); - } - } - - return 0; -} - #ifdef CONFIG_RTL8XXXU_UNTESTED static int rtl8192cu_parse_efuse(struct rtl8xxxu_priv *priv) @@ -2816,35 +2406,6 @@ void rtl8xxxu_reset_8051(struct rtl8xxxu_priv *priv) rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func); } -static void rtl8723bu_reset_8051(struct rtl8xxxu_priv *priv) -{ - u8 val8; - u16 sys_func; - - val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL); - val8 &= ~BIT(1); - rtl8xxxu_write8(priv, REG_RSV_CTRL, val8); - - val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1); - val8 &= ~BIT(0); - rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8); - - sys_func = rtl8xxxu_read16(priv, REG_SYS_FUNC); - sys_func &= ~SYS_FUNC_CPU_ENABLE; - rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func); - - val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL); - val8 &= ~BIT(1); - rtl8xxxu_write8(priv, REG_RSV_CTRL, val8); - - val8 = rtl8xxxu_read8(priv, REG_RSV_CTRL + 1); - val8 |= BIT(0); - rtl8xxxu_write8(priv, REG_RSV_CTRL + 1, val8); - - sys_func |= SYS_FUNC_CPU_ENABLE; - rtl8xxxu_write16(priv, REG_SYS_FUNC, sys_func); -} - static int rtl8xxxu_start_firmware(struct rtl8xxxu_priv *priv) { struct device *dev = &priv->udev->dev; @@ -3053,20 +2614,6 @@ static int rtl8723au_load_firmware(struct rtl8xxxu_priv *priv) return ret; } -static int rtl8723bu_load_firmware(struct rtl8xxxu_priv *priv) -{ - char *fw_name; - int ret; - - if (priv->enable_bluetooth) - fw_name = "rtlwifi/rtl8723bu_bt.bin"; - else - fw_name = "rtlwifi/rtl8723bu_nic.bin"; - - ret = rtl8xxxu_load_firmware(priv, fw_name); - return ret; -} - #ifdef CONFIG_RTL8XXXU_UNTESTED static int rtl8192cu_load_firmware(struct rtl8xxxu_priv *priv) @@ -3088,7 +2635,7 @@ static int rtl8192cu_load_firmware(struct rtl8xxxu_priv *priv) #endif -static void rtl8xxxu_firmware_self_reset(struct rtl8xxxu_priv *priv) +void rtl8xxxu_firmware_self_reset(struct rtl8xxxu_priv *priv) { u16 val16; int i = 100; @@ -3115,44 +2662,6 @@ static void rtl8xxxu_firmware_self_reset(struct rtl8xxxu_priv *priv) } } -static void rtl8723bu_phy_init_antenna_selection(struct rtl8xxxu_priv *priv) -{ - u32 val32; - - val32 = rtl8xxxu_read32(priv, REG_PAD_CTRL1); - val32 &= ~(BIT(20) | BIT(24)); - rtl8xxxu_write32(priv, REG_PAD_CTRL1, val32); - - val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG); - val32 &= ~BIT(4); - rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, val32); - - val32 = rtl8xxxu_read32(priv, REG_GPIO_MUXCFG); - val32 |= BIT(3); - rtl8xxxu_write32(priv, REG_GPIO_MUXCFG, val32); - - val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); - val32 |= BIT(24); - rtl8xxxu_write32(priv, REG_LEDCFG0, val32); - - val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); - val32 &= ~BIT(23); - rtl8xxxu_write32(priv, REG_LEDCFG0, val32); - - val32 = rtl8xxxu_read32(priv, REG_RFE_BUFFER); - val32 |= (BIT(0) | BIT(1)); - rtl8xxxu_write32(priv, REG_RFE_BUFFER, val32); - - val32 = rtl8xxxu_read32(priv, REG_RFE_CTRL_ANTA_SRC); - val32 &= 0xffffff00; - val32 |= 0x77; - rtl8xxxu_write32(priv, REG_RFE_CTRL_ANTA_SRC, val32); - - val32 = rtl8xxxu_read32(priv, REG_PWR_DATA); - val32 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN; - rtl8xxxu_write32(priv, REG_PWR_DATA, val32); -} - static int rtl8xxxu_init_mac(struct rtl8xxxu_priv *priv) { @@ -3262,29 +2771,6 @@ static void rtl8xxxu_gen1_init_phy_bb(struct rtl8xxxu_priv *priv) rtl8xxxu_write32(priv, REG_LDOA15_CTRL, val32); } -static void rtl8723bu_init_phy_bb(struct rtl8xxxu_priv *priv) -{ - u8 val8; - u16 val16; - - val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); - val16 |= SYS_FUNC_BB_GLB_RSTN | SYS_FUNC_BBRSTB | SYS_FUNC_DIO_RF; - rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); - - rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00); - - /* 6. 0x1f[7:0] = 0x07 */ - val8 = RF_ENABLE | RF_RSTB | RF_SDMRSTB; - rtl8xxxu_write8(priv, REG_RF_CTRL, val8); - - /* Why? */ - rtl8xxxu_write8(priv, REG_SYS_FUNC, 0xe3); - rtl8xxxu_write8(priv, REG_AFE_XTAL_CTRL + 1, 0x80); - rtl8xxxu_init_phy_regs(priv, rtl8723b_phy_1t_init_table); - - rtl8xxxu_init_phy_regs(priv, rtl8xxx_agc_8723bu_table); -} - /* * Most of this is black magic retrieved from the old rtl8723au driver */ @@ -3499,22 +2985,6 @@ static int rtl8723au_init_phy_rf(struct rtl8xxxu_priv *priv) return ret; } -static int rtl8723bu_init_phy_rf(struct rtl8xxxu_priv *priv) -{ - int ret; - - ret = rtl8xxxu_init_phy_rf(priv, rtl8723bu_radioa_1t_init_table, RF_A); - /* - * PHY LCK - */ - rtl8xxxu_write_rfreg(priv, RF_A, 0xb0, 0xdfbe0); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_MODE_AG, 0x8c01); - msleep(200); - rtl8xxxu_write_rfreg(priv, RF_A, 0xb0, 0xdffe0); - - return ret; -} - #ifdef CONFIG_RTL8XXXU_UNTESTED static int rtl8192cu_init_phy_rf(struct rtl8xxxu_priv *priv) { @@ -4199,325 +3669,6 @@ out: return result; } -static int rtl8723bu_iqk_path_a(struct rtl8xxxu_priv *priv) -{ - u32 reg_eac, reg_e94, reg_e9c, path_sel, val32; - int result = 0; - - path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH); - - /* - * Leave IQK mode - */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - - /* - * Enable path A PA in TX IQK mode - */ - val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); - val32 |= 0x80000; - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x20000); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0003f); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xc7f87); - - /* - * Tx IQK setting - */ - rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00); - rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800); - - /* path-A IQK setting */ - rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c); - rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c); - rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c); - rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c); - - rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x821403ea); - rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28110000); - rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000); - rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000); - - /* LO calibration setting */ - rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x00462911); - - /* - * Enter IQK mode - */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - val32 |= 0x80800000; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - - /* - * The vendor driver indicates the USB module is always using - * S0S1 path 1 for the 8723bu. This may be different for 8192eu - */ - if (priv->rf_paths > 1) - rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000); - else - rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280); - - /* - * Bit 12 seems to be BT_GRANT, and is only found in the 8723bu. - * No trace of this in the 8192eu or 8188eu vendor drivers. - */ - rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800); - - /* One shot, path A LOK & IQK */ - rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000); - rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000); - - mdelay(1); - - /* Restore Ant Path */ - rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel); -#ifdef RTL8723BU_BT - /* GNT_BT = 1 */ - rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800); -#endif - - /* - * Leave IQK mode - */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - - /* Check failed */ - reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2); - reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A); - reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A); - - val32 = (reg_e9c >> 16) & 0x3ff; - if (val32 & 0x200) - val32 = 0x400 - val32; - - if (!(reg_eac & BIT(28)) && - ((reg_e94 & 0x03ff0000) != 0x01420000) && - ((reg_e9c & 0x03ff0000) != 0x00420000) && - ((reg_e94 & 0x03ff0000) < 0x01100000) && - ((reg_e94 & 0x03ff0000) > 0x00f00000) && - val32 < 0xf) - result |= 0x01; - else /* If TX not OK, ignore RX */ - goto out; - -out: - return result; -} - -static int rtl8723bu_rx_iqk_path_a(struct rtl8xxxu_priv *priv) -{ - u32 reg_ea4, reg_eac, reg_e94, reg_e9c, path_sel, val32; - int result = 0; - - path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH); - - /* - * Leave IQK mode - */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - - /* - * Enable path A PA in TX IQK mode - */ - val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); - val32 |= 0x80000; - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7fb7); - - /* - * Tx IQK setting - */ - rtl8xxxu_write32(priv, REG_TX_IQK, 0x01007c00); - rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800); - - /* path-A IQK setting */ - rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x18008c1c); - rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x38008c1c); - rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c); - rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c); - - rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82160ff0); - rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x28110000); - rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000); - rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000); - - /* LO calibration setting */ - rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a911); - - /* - * Enter IQK mode - */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - val32 |= 0x80800000; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - - /* - * The vendor driver indicates the USB module is always using - * S0S1 path 1 for the 8723bu. This may be different for 8192eu - */ - if (priv->rf_paths > 1) - rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000); - else - rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280); - - /* - * Bit 12 seems to be BT_GRANT, and is only found in the 8723bu. - * No trace of this in the 8192eu or 8188eu vendor drivers. - */ - rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800); - - /* One shot, path A LOK & IQK */ - rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000); - rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000); - - mdelay(1); - - /* Restore Ant Path */ - rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel); -#ifdef RTL8723BU_BT - /* GNT_BT = 1 */ - rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800); -#endif - - /* - * Leave IQK mode - */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - - /* Check failed */ - reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2); - reg_e94 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_A); - reg_e9c = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_A); - - val32 = (reg_e9c >> 16) & 0x3ff; - if (val32 & 0x200) - val32 = 0x400 - val32; - - if (!(reg_eac & BIT(28)) && - ((reg_e94 & 0x03ff0000) != 0x01420000) && - ((reg_e9c & 0x03ff0000) != 0x00420000) && - ((reg_e94 & 0x03ff0000) < 0x01100000) && - ((reg_e94 & 0x03ff0000) > 0x00f00000) && - val32 < 0xf) - result |= 0x01; - else /* If TX not OK, ignore RX */ - goto out; - - val32 = 0x80007c00 | (reg_e94 &0x3ff0000) | - ((reg_e9c & 0x3ff0000) >> 16); - rtl8xxxu_write32(priv, REG_TX_IQK, val32); - - /* - * Modify RX IQK mode - */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); - val32 |= 0x80000; - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7d77); - - /* - * PA, PAD setting - */ - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0xf80); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_55, 0x4021f); - - /* - * RX IQK setting - */ - rtl8xxxu_write32(priv, REG_RX_IQK, 0x01004800); - - /* path-A IQK setting */ - rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x38008c1c); - rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x18008c1c); - rtl8xxxu_write32(priv, REG_TX_IQK_TONE_B, 0x38008c1c); - rtl8xxxu_write32(priv, REG_RX_IQK_TONE_B, 0x38008c1c); - - rtl8xxxu_write32(priv, REG_TX_IQK_PI_A, 0x82110000); - rtl8xxxu_write32(priv, REG_RX_IQK_PI_A, 0x2816001f); - rtl8xxxu_write32(priv, REG_TX_IQK_PI_B, 0x82110000); - rtl8xxxu_write32(priv, REG_RX_IQK_PI_B, 0x28110000); - - /* LO calibration setting */ - rtl8xxxu_write32(priv, REG_IQK_AGC_RSP, 0x0046a8d1); - - /* - * Enter IQK mode - */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - val32 |= 0x80800000; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - - if (priv->rf_paths > 1) - rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000000); - else - rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00000280); - - /* - * Disable BT - */ - rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00000800); - - /* One shot, path A LOK & IQK */ - rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf9000000); - rtl8xxxu_write32(priv, REG_IQK_AGC_PTS, 0xf8000000); - - mdelay(1); - - /* Restore Ant Path */ - rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, path_sel); -#ifdef RTL8723BU_BT - /* GNT_BT = 1 */ - rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, 0x00001800); -#endif - - /* - * Leave IQK mode - */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - - /* Check failed */ - reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2); - reg_ea4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_A_2); - - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_DF, 0x780); - - val32 = (reg_eac >> 16) & 0x3ff; - if (val32 & 0x200) - val32 = 0x400 - val32; - - if (!(reg_eac & BIT(27)) && - ((reg_ea4 & 0x03ff0000) != 0x01320000) && - ((reg_eac & 0x03ff0000) != 0x00360000) && - ((reg_ea4 & 0x03ff0000) < 0x01100000) && - ((reg_ea4 & 0x03ff0000) > 0x00f00000) && - val32 < 0xf) - result |= 0x02; - else /* If TX not OK, ignore RX */ - goto out; -out: - return result; -} - static void rtl8xxxu_phy_iqcalibrate(struct rtl8xxxu_priv *priv, int result[][8], int t) { @@ -4723,215 +3874,7 @@ static void rtl8xxxu_phy_iqcalibrate(struct rtl8xxxu_priv *priv, } } -static void rtl8723bu_phy_iqcalibrate(struct rtl8xxxu_priv *priv, - int result[][8], int t) -{ - struct device *dev = &priv->udev->dev; - u32 i, val32; - int path_a_ok /*, path_b_ok */; - int retry = 2; - const u32 adda_regs[RTL8XXXU_ADDA_REGS] = { - REG_FPGA0_XCD_SWITCH_CTRL, REG_BLUETOOTH, - REG_RX_WAIT_CCA, REG_TX_CCK_RFON, - REG_TX_CCK_BBON, REG_TX_OFDM_RFON, - REG_TX_OFDM_BBON, REG_TX_TO_RX, - REG_TX_TO_TX, REG_RX_CCK, - REG_RX_OFDM, REG_RX_WAIT_RIFS, - REG_RX_TO_RX, REG_STANDBY, - REG_SLEEP, REG_PMPD_ANAEN - }; - const u32 iqk_mac_regs[RTL8XXXU_MAC_REGS] = { - REG_TXPAUSE, REG_BEACON_CTRL, - REG_BEACON_CTRL_1, REG_GPIO_MUXCFG - }; - const u32 iqk_bb_regs[RTL8XXXU_BB_REGS] = { - REG_OFDM0_TRX_PATH_ENABLE, REG_OFDM0_TR_MUX_PAR, - REG_FPGA0_XCD_RF_SW_CTRL, REG_CONFIG_ANT_A, REG_CONFIG_ANT_B, - REG_FPGA0_XAB_RF_SW_CTRL, REG_FPGA0_XA_RF_INT_OE, - REG_FPGA0_XB_RF_INT_OE, REG_FPGA0_RF_MODE - }; - u8 xa_agc = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1) & 0xff; - u8 xb_agc = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1) & 0xff; - - /* - * Note: IQ calibration must be performed after loading - * PHY_REG.txt , and radio_a, radio_b.txt - */ - - if (t == 0) { - /* Save ADDA parameters, turn Path A ADDA on */ - rtl8xxxu_save_regs(priv, adda_regs, priv->adda_backup, - RTL8XXXU_ADDA_REGS); - rtl8xxxu_save_mac_regs(priv, iqk_mac_regs, priv->mac_backup); - rtl8xxxu_save_regs(priv, iqk_bb_regs, - priv->bb_backup, RTL8XXXU_BB_REGS); - } - - rtl8xxxu_path_adda_on(priv, adda_regs, true); - - /* MAC settings */ - rtl8xxxu_mac_calibration(priv, iqk_mac_regs, priv->mac_backup); - - val32 = rtl8xxxu_read32(priv, REG_CCK0_AFE_SETTING); - val32 |= 0x0f000000; - rtl8xxxu_write32(priv, REG_CCK0_AFE_SETTING, val32); - - rtl8xxxu_write32(priv, REG_OFDM0_TRX_PATH_ENABLE, 0x03a05600); - rtl8xxxu_write32(priv, REG_OFDM0_TR_MUX_PAR, 0x000800e4); - rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_SW_CTRL, 0x22204000); - - /* - * RX IQ calibration setting for 8723B D cut large current issue - * when leaving IPS - */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - - val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); - val32 |= 0x80000; - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); - - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x30000); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xf7fb7); - - val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED); - val32 |= 0x20; - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32); - - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_43, 0x60fbd); - - for (i = 0; i < retry; i++) { - path_a_ok = rtl8723bu_iqk_path_a(priv); - if (path_a_ok == 0x01) { - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - - val32 = rtl8xxxu_read32(priv, - REG_TX_POWER_BEFORE_IQK_A); - result[t][0] = (val32 >> 16) & 0x3ff; - val32 = rtl8xxxu_read32(priv, - REG_TX_POWER_AFTER_IQK_A); - result[t][1] = (val32 >> 16) & 0x3ff; - - break; - } - } - - if (!path_a_ok) - dev_dbg(dev, "%s: Path A TX IQK failed!\n", __func__); - - for (i = 0; i < retry; i++) { - path_a_ok = rtl8723bu_rx_iqk_path_a(priv); - if (path_a_ok == 0x03) { - val32 = rtl8xxxu_read32(priv, - REG_RX_POWER_BEFORE_IQK_A_2); - result[t][2] = (val32 >> 16) & 0x3ff; - val32 = rtl8xxxu_read32(priv, - REG_RX_POWER_AFTER_IQK_A_2); - result[t][3] = (val32 >> 16) & 0x3ff; - - break; - } - } - - if (!path_a_ok) - dev_dbg(dev, "%s: Path A RX IQK failed!\n", __func__); - - if (priv->tx_paths > 1) { -#if 1 - dev_warn(dev, "%s: Path B not supported\n", __func__); -#else - - /* - * Path A into standby - */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_AC, 0x10000); - - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - val32 |= 0x80800000; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - - /* Turn Path B ADDA on */ - rtl8xxxu_path_adda_on(priv, adda_regs, false); - - for (i = 0; i < retry; i++) { - path_b_ok = rtl8xxxu_iqk_path_b(priv); - if (path_b_ok == 0x03) { - val32 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B); - result[t][4] = (val32 >> 16) & 0x3ff; - val32 = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B); - result[t][5] = (val32 >> 16) & 0x3ff; - break; - } - } - - if (!path_b_ok) - dev_dbg(dev, "%s: Path B IQK failed!\n", __func__); - - for (i = 0; i < retry; i++) { - path_b_ok = rtl8723bu_rx_iqk_path_b(priv); - if (path_a_ok == 0x03) { - val32 = rtl8xxxu_read32(priv, - REG_RX_POWER_BEFORE_IQK_B_2); - result[t][6] = (val32 >> 16) & 0x3ff; - val32 = rtl8xxxu_read32(priv, - REG_RX_POWER_AFTER_IQK_B_2); - result[t][7] = (val32 >> 16) & 0x3ff; - break; - } - } - - if (!path_b_ok) - dev_dbg(dev, "%s: Path B RX IQK failed!\n", __func__); -#endif - } - - /* Back to BB mode, load original value */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 &= 0x000000ff; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - - if (t) { - /* Reload ADDA power saving parameters */ - rtl8xxxu_restore_regs(priv, adda_regs, priv->adda_backup, - RTL8XXXU_ADDA_REGS); - - /* Reload MAC parameters */ - rtl8xxxu_restore_mac_regs(priv, iqk_mac_regs, priv->mac_backup); - - /* Reload BB parameters */ - rtl8xxxu_restore_regs(priv, iqk_bb_regs, - priv->bb_backup, RTL8XXXU_BB_REGS); - - /* Restore RX initial gain */ - val32 = rtl8xxxu_read32(priv, REG_OFDM0_XA_AGC_CORE1); - val32 &= 0xffffff00; - rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | 0x50); - rtl8xxxu_write32(priv, REG_OFDM0_XA_AGC_CORE1, val32 | xa_agc); - - if (priv->tx_paths > 1) { - val32 = rtl8xxxu_read32(priv, REG_OFDM0_XB_AGC_CORE1); - val32 &= 0xffffff00; - rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1, - val32 | 0x50); - rtl8xxxu_write32(priv, REG_OFDM0_XB_AGC_CORE1, - val32 | xb_agc); - } - - /* Load 0xe30 IQC default value */ - rtl8xxxu_write32(priv, REG_TX_IQK_TONE_A, 0x01008c00); - rtl8xxxu_write32(priv, REG_RX_IQK_TONE_A, 0x01008c00); - } -} - -static void rtl8xxxu_prepare_calibrate(struct rtl8xxxu_priv *priv, u8 start) +void rtl8xxxu_prepare_calibrate(struct rtl8xxxu_priv *priv, u8 start) { struct h2c_cmd h2c; @@ -5049,130 +3992,6 @@ static void rtl8xxxu_gen1_phy_iq_calibrate(struct rtl8xxxu_priv *priv) rtl8xxxu_prepare_calibrate(priv, 0); } -static void rtl8723bu_phy_iq_calibrate(struct rtl8xxxu_priv *priv) -{ - struct device *dev = &priv->udev->dev; - int result[4][8]; /* last is final result */ - int i, candidate; - bool path_a_ok, path_b_ok; - u32 reg_e94, reg_e9c, reg_ea4, reg_eac; - u32 reg_eb4, reg_ebc, reg_ec4, reg_ecc; - u32 val32, bt_control; - s32 reg_tmp = 0; - bool simu; - - rtl8xxxu_prepare_calibrate(priv, 1); - - memset(result, 0, sizeof(result)); - candidate = -1; - - path_a_ok = false; - path_b_ok = false; - - bt_control = rtl8xxxu_read32(priv, REG_BT_CONTROL_8723BU); - - for (i = 0; i < 3; i++) { - rtl8723bu_phy_iqcalibrate(priv, result, i); - - if (i == 1) { - simu = rtl8xxxu_gen2_simularity_compare(priv, - result, 0, 1); - if (simu) { - candidate = 0; - break; - } - } - - if (i == 2) { - simu = rtl8xxxu_gen2_simularity_compare(priv, - result, 0, 2); - if (simu) { - candidate = 0; - break; - } - - simu = rtl8xxxu_gen2_simularity_compare(priv, - result, 1, 2); - if (simu) { - candidate = 1; - } else { - for (i = 0; i < 8; i++) - reg_tmp += result[3][i]; - - if (reg_tmp) - candidate = 3; - else - candidate = -1; - } - } - } - - for (i = 0; i < 4; i++) { - reg_e94 = result[i][0]; - reg_e9c = result[i][1]; - reg_ea4 = result[i][2]; - reg_eac = result[i][3]; - reg_eb4 = result[i][4]; - reg_ebc = result[i][5]; - reg_ec4 = result[i][6]; - reg_ecc = result[i][7]; - } - - if (candidate >= 0) { - reg_e94 = result[candidate][0]; - priv->rege94 = reg_e94; - reg_e9c = result[candidate][1]; - priv->rege9c = reg_e9c; - reg_ea4 = result[candidate][2]; - reg_eac = result[candidate][3]; - reg_eb4 = result[candidate][4]; - priv->regeb4 = reg_eb4; - reg_ebc = result[candidate][5]; - priv->regebc = reg_ebc; - reg_ec4 = result[candidate][6]; - reg_ecc = result[candidate][7]; - dev_dbg(dev, "%s: candidate is %x\n", __func__, candidate); - dev_dbg(dev, - "%s: e94 =%x e9c=%x ea4=%x eac=%x eb4=%x ebc=%x ec4=%x " - "ecc=%x\n ", __func__, reg_e94, reg_e9c, - reg_ea4, reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc); - path_a_ok = true; - path_b_ok = true; - } else { - reg_e94 = reg_eb4 = priv->rege94 = priv->regeb4 = 0x100; - reg_e9c = reg_ebc = priv->rege9c = priv->regebc = 0x0; - } - - if (reg_e94 && candidate >= 0) - rtl8xxxu_fill_iqk_matrix_a(priv, path_a_ok, result, - candidate, (reg_ea4 == 0)); - - if (priv->tx_paths > 1 && reg_eb4) - rtl8xxxu_fill_iqk_matrix_b(priv, path_b_ok, result, - candidate, (reg_ec4 == 0)); - - rtl8xxxu_save_regs(priv, rtl8xxxu_iqk_phy_iq_bb_reg, - priv->bb_recovery_backup, RTL8XXXU_BB_REGS); - - rtl8xxxu_write32(priv, REG_BT_CONTROL_8723BU, bt_control); - - val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_WE_LUT); - val32 |= 0x80000; - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_WE_LUT, val32); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_RCK_OS, 0x18000); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G1, 0x0001f); - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_TXPA_G2, 0xe6177); - val32 = rtl8xxxu_read_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED); - val32 |= 0x20; - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32); - rtl8xxxu_write_rfreg(priv, RF_A, 0x43, 0x300bd); - - if (priv->rf_paths > 1) - dev_dbg(dev, "%s: 8723BU 2T not supported\n", __func__); - - rtl8xxxu_prepare_calibrate(priv, 0); -} - static void rtl8723a_phy_lc_calibrate(struct rtl8xxxu_priv *priv) { u32 val32; @@ -5341,65 +4160,7 @@ exit: return ret; } -static int rtl8723bu_active_to_emu(struct rtl8xxxu_priv *priv) -{ - u8 val8; - u16 val16; - u32 val32; - int count, ret = 0; - - /* Turn off RF */ - rtl8xxxu_write8(priv, REG_RF_CTRL, 0); - - /* Enable rising edge triggering interrupt */ - val16 = rtl8xxxu_read16(priv, REG_GPIO_INTM); - val16 &= ~GPIO_INTM_EDGE_TRIG_IRQ; - rtl8xxxu_write16(priv, REG_GPIO_INTM, val16); - - /* Release WLON reset 0x04[16]= 1*/ - val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); - val32 |= APS_FSMCO_WLON_RESET; - rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); - - /* 0x0005[1] = 1 turn off MAC by HW state machine*/ - val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); - val8 |= BIT(1); - rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); - - for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { - val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); - if ((val8 & BIT(1)) == 0) - break; - udelay(10); - } - - if (!count) { - dev_warn(&priv->udev->dev, "%s: Disabling MAC timed out\n", - __func__); - ret = -EBUSY; - goto exit; - } - - /* Enable BT control XTAL setting */ - val8 = rtl8xxxu_read8(priv, REG_AFE_MISC); - val8 &= ~AFE_MISC_WL_XTAL_CTRL; - rtl8xxxu_write8(priv, REG_AFE_MISC, val8); - - /* 0x0000[5] = 1 analog Ips to digital, 1:isolation */ - val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL); - val8 |= SYS_ISO_ANALOG_IPS; - rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8); - - /* 0x0020[0] = 0 disable LDOA12 MACRO block*/ - val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL); - val8 &= ~LDOA15_ENABLE; - rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8); - -exit: - return ret; -} - -static int rtl8xxxu_active_to_lps(struct rtl8xxxu_priv *priv) +int rtl8xxxu_active_to_lps(struct rtl8xxxu_priv *priv) { u8 val8; u8 val32; @@ -5455,7 +4216,7 @@ exit: return ret; } -static void rtl8723a_disabled_to_emu(struct rtl8xxxu_priv *priv) +void rtl8723a_disabled_to_emu(struct rtl8xxxu_priv *priv) { u8 val8; @@ -5567,127 +4328,6 @@ exit: return ret; } -static int rtl8723b_emu_to_active(struct rtl8xxxu_priv *priv) -{ - u8 val8; - u32 val32; - int count, ret = 0; - - /* 0x20[0] = 1 enable LDOA12 MACRO block for all interface */ - val8 = rtl8xxxu_read8(priv, REG_LDOA15_CTRL); - val8 |= LDOA15_ENABLE; - rtl8xxxu_write8(priv, REG_LDOA15_CTRL, val8); - - /* 0x67[0] = 0 to disable BT_GPS_SEL pins*/ - val8 = rtl8xxxu_read8(priv, 0x0067); - val8 &= ~BIT(4); - rtl8xxxu_write8(priv, 0x0067, val8); - - mdelay(1); - - /* 0x00[5] = 0 release analog Ips to digital, 1:isolation */ - val8 = rtl8xxxu_read8(priv, REG_SYS_ISO_CTRL); - val8 &= ~SYS_ISO_ANALOG_IPS; - rtl8xxxu_write8(priv, REG_SYS_ISO_CTRL, val8); - - /* Disable SW LPS 0x04[10]= 0 */ - val32 = rtl8xxxu_read8(priv, REG_APS_FSMCO); - val32 &= ~APS_FSMCO_SW_LPS; - rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); - - /* Wait until 0x04[17] = 1 power ready */ - for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { - val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); - if (val32 & BIT(17)) - break; - - udelay(10); - } - - if (!count) { - ret = -EBUSY; - goto exit; - } - - /* We should be able to optimize the following three entries into one */ - - /* Release WLON reset 0x04[16]= 1*/ - val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); - val32 |= APS_FSMCO_WLON_RESET; - rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); - - /* Disable HWPDN 0x04[15]= 0*/ - val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); - val32 &= ~APS_FSMCO_HW_POWERDOWN; - rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); - - /* Disable WL suspend*/ - val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); - val32 &= ~(APS_FSMCO_HW_SUSPEND | APS_FSMCO_PCIE); - rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); - - /* Set, then poll until 0 */ - val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); - val32 |= APS_FSMCO_MAC_ENABLE; - rtl8xxxu_write32(priv, REG_APS_FSMCO, val32); - - for (count = RTL8XXXU_MAX_REG_POLL; count; count--) { - val32 = rtl8xxxu_read32(priv, REG_APS_FSMCO); - if ((val32 & APS_FSMCO_MAC_ENABLE) == 0) { - ret = 0; - break; - } - udelay(10); - } - - if (!count) { - ret = -EBUSY; - goto exit; - } - - /* Enable WL control XTAL setting */ - val8 = rtl8xxxu_read8(priv, REG_AFE_MISC); - val8 |= AFE_MISC_WL_XTAL_CTRL; - rtl8xxxu_write8(priv, REG_AFE_MISC, val8); - - /* Enable falling edge triggering interrupt */ - val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 1); - val8 |= BIT(1); - rtl8xxxu_write8(priv, REG_GPIO_INTM + 1, val8); - - /* Enable GPIO9 interrupt mode */ - val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2 + 1); - val8 |= BIT(1); - rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2 + 1, val8); - - /* Enable GPIO9 input mode */ - val8 = rtl8xxxu_read8(priv, REG_GPIO_IO_SEL_2); - val8 &= ~BIT(1); - rtl8xxxu_write8(priv, REG_GPIO_IO_SEL_2, val8); - - /* Enable HSISR GPIO[C:0] interrupt */ - val8 = rtl8xxxu_read8(priv, REG_HSIMR); - val8 |= BIT(0); - rtl8xxxu_write8(priv, REG_HSIMR, val8); - - /* Enable HSISR GPIO9 interrupt */ - val8 = rtl8xxxu_read8(priv, REG_HSIMR + 2); - val8 |= BIT(1); - rtl8xxxu_write8(priv, REG_HSIMR + 2, val8); - - val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL); - val8 |= MULTI_WIFI_HW_ROF_EN; - rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL, val8); - - /* For GPIO9 internal pull high setting BIT(14) */ - val8 = rtl8xxxu_read8(priv, REG_MULTI_FUNC_CTRL + 1); - val8 |= BIT(6); - rtl8xxxu_write8(priv, REG_MULTI_FUNC_CTRL + 1, val8); - -exit: - return ret; -} - static int rtl8xxxu_emu_to_disabled(struct rtl8xxxu_priv *priv) { u8 val8; @@ -5713,7 +4353,7 @@ static int rtl8xxxu_emu_to_disabled(struct rtl8xxxu_priv *priv) return 0; } -static int rtl8xxxu_flush_fifo(struct rtl8xxxu_priv *priv) +int rtl8xxxu_flush_fifo(struct rtl8xxxu_priv *priv) { struct device *dev = &priv->udev->dev; u32 val32; @@ -5836,62 +4476,6 @@ exit: return ret; } -static int rtl8723bu_power_on(struct rtl8xxxu_priv *priv) -{ - u8 val8; - u16 val16; - u32 val32; - int ret; - - rtl8723a_disabled_to_emu(priv); - - ret = rtl8723b_emu_to_active(priv); - if (ret) - goto exit; - - /* - * Enable MAC DMA/WMAC/SCHEDULE/SEC block - * Set CR bit10 to enable 32k calibration. - */ - val16 = rtl8xxxu_read16(priv, REG_CR); - val16 |= (CR_HCI_TXDMA_ENABLE | CR_HCI_RXDMA_ENABLE | - CR_TXDMA_ENABLE | CR_RXDMA_ENABLE | - CR_PROTOCOL_ENABLE | CR_SCHEDULE_ENABLE | - CR_MAC_TX_ENABLE | CR_MAC_RX_ENABLE | - CR_SECURITY_ENABLE | CR_CALTIMER_ENABLE); - rtl8xxxu_write16(priv, REG_CR, val16); - - /* - * BT coexist power on settings. This is identical for 1 and 2 - * antenna parts. - */ - rtl8xxxu_write8(priv, REG_PAD_CTRL1 + 3, 0x20); - - val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); - val16 |= SYS_FUNC_BBRSTB | SYS_FUNC_BB_GLB_RSTN; - rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); - - rtl8xxxu_write8(priv, REG_BT_CONTROL_8723BU + 1, 0x18); - rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04); - rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00); - /* Antenna inverse */ - rtl8xxxu_write8(priv, 0xfe08, 0x01); - - val16 = rtl8xxxu_read16(priv, REG_PWR_DATA); - val16 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN; - rtl8xxxu_write16(priv, REG_PWR_DATA, val16); - - val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); - val32 |= LEDCFG0_DPDT_SELECT; - rtl8xxxu_write32(priv, REG_LEDCFG0, val32); - - val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1); - val8 &= ~PAD_CTRL1_SW_DPDT_SEL_DATA; - rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8); -exit: - return ret; -} - #ifdef CONFIG_RTL8XXXU_UNTESTED static int rtl8192cu_power_on(struct rtl8xxxu_priv *priv) @@ -6051,48 +4635,6 @@ void rtl8xxxu_power_off(struct rtl8xxxu_priv *priv) rtl8xxxu_write8(priv, REG_RSV_CTRL, 0x0e); } -static void rtl8723bu_power_off(struct rtl8xxxu_priv *priv) -{ - u8 val8; - u16 val16; - - rtl8xxxu_flush_fifo(priv); - - /* - * Disable TX report timer - */ - val8 = rtl8xxxu_read8(priv, REG_TX_REPORT_CTRL); - val8 &= ~TX_REPORT_CTRL_TIMER_ENABLE; - rtl8xxxu_write8(priv, REG_TX_REPORT_CTRL, val8); - - rtl8xxxu_write8(priv, REG_CR, 0x0000); - - rtl8xxxu_active_to_lps(priv); - - /* Reset Firmware if running in RAM */ - if (rtl8xxxu_read8(priv, REG_MCU_FW_DL) & MCU_FW_RAM_SEL) - rtl8xxxu_firmware_self_reset(priv); - - /* Reset MCU */ - val16 = rtl8xxxu_read16(priv, REG_SYS_FUNC); - val16 &= ~SYS_FUNC_CPU_ENABLE; - rtl8xxxu_write16(priv, REG_SYS_FUNC, val16); - - /* Reset MCU ready status */ - rtl8xxxu_write8(priv, REG_MCU_FW_DL, 0x00); - - rtl8723bu_active_to_emu(priv); - - val8 = rtl8xxxu_read8(priv, REG_APS_FSMCO + 1); - val8 |= BIT(3); /* APS_FSMCO_HW_SUSPEND */ - rtl8xxxu_write8(priv, REG_APS_FSMCO + 1, val8); - - /* 0x48[16] = 1 to enable GPIO9 as EXT wakeup */ - val8 = rtl8xxxu_read8(priv, REG_GPIO_INTM + 2); - val8 |= BIT(0); - rtl8xxxu_write8(priv, REG_GPIO_INTM + 2, val8); -} - #ifdef NEED_PS_TDMA static void rtl8723bu_set_ps_tdma(struct rtl8xxxu_priv *priv, u8 arg1, u8 arg2, u8 arg3, u8 arg4, u8 arg5) @@ -6110,113 +4652,6 @@ static void rtl8723bu_set_ps_tdma(struct rtl8xxxu_priv *priv, } #endif -static void rtl8723b_enable_rf(struct rtl8xxxu_priv *priv) -{ - struct h2c_cmd h2c; - u32 val32; - u8 val8; - - /* - * No indication anywhere as to what 0x0790 does. The 2 antenna - * vendor code preserves bits 6-7 here. - */ - rtl8xxxu_write8(priv, 0x0790, 0x05); - /* - * 0x0778 seems to be related to enabling the number of antennas - * In the vendor driver halbtc8723b2ant_InitHwConfig() sets it - * to 0x03, while halbtc8723b1ant_InitHwConfig() sets it to 0x01 - */ - rtl8xxxu_write8(priv, 0x0778, 0x01); - - val8 = rtl8xxxu_read8(priv, REG_GPIO_MUXCFG); - val8 |= BIT(5); - rtl8xxxu_write8(priv, REG_GPIO_MUXCFG, val8); - - rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_IQADJ_G1, 0x780); - - rtl8723bu_write_btreg(priv, 0x3c, 0x15); /* BT TRx Mask on */ - - /* - * Set BT grant to low - */ - memset(&h2c, 0, sizeof(struct h2c_cmd)); - h2c.bt_grant.cmd = H2C_8723B_BT_GRANT; - h2c.bt_grant.data = 0; - rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_grant)); - - /* - * WLAN action by PTA - */ - rtl8xxxu_write8(priv, REG_WLAN_ACT_CONTROL_8723B, 0x04); - - /* - * BT select S0/S1 controlled by WiFi - */ - val8 = rtl8xxxu_read8(priv, 0x0067); - val8 |= BIT(5); - rtl8xxxu_write8(priv, 0x0067, val8); - - val32 = rtl8xxxu_read32(priv, REG_PWR_DATA); - val32 |= PWR_DATA_EEPRPAD_RFE_CTRL_EN; - rtl8xxxu_write32(priv, REG_PWR_DATA, val32); - - /* - * Bits 6/7 are marked in/out ... but for what? - */ - rtl8xxxu_write8(priv, 0x0974, 0xff); - - val32 = rtl8xxxu_read32(priv, REG_RFE_BUFFER); - val32 |= (BIT(0) | BIT(1)); - rtl8xxxu_write32(priv, REG_RFE_BUFFER, val32); - - rtl8xxxu_write8(priv, REG_RFE_CTRL_ANTA_SRC, 0x77); - - val32 = rtl8xxxu_read32(priv, REG_LEDCFG0); - val32 &= ~BIT(24); - val32 |= BIT(23); - rtl8xxxu_write32(priv, REG_LEDCFG0, val32); - - /* - * Fix external switch Main->S1, Aux->S0 - */ - val8 = rtl8xxxu_read8(priv, REG_PAD_CTRL1); - val8 &= ~BIT(0); - rtl8xxxu_write8(priv, REG_PAD_CTRL1, val8); - - memset(&h2c, 0, sizeof(struct h2c_cmd)); - h2c.ant_sel_rsv.cmd = H2C_8723B_ANT_SEL_RSV; - h2c.ant_sel_rsv.ant_inverse = 1; - h2c.ant_sel_rsv.int_switch_type = 0; - rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.ant_sel_rsv)); - - /* - * 0x280, 0x00, 0x200, 0x80 - not clear - */ - rtl8xxxu_write32(priv, REG_S0S1_PATH_SWITCH, 0x00); - - /* - * Software control, antenna at WiFi side - */ -#ifdef NEED_PS_TDMA - rtl8723bu_set_ps_tdma(priv, 0x08, 0x00, 0x00, 0x00, 0x00); -#endif - - rtl8xxxu_write32(priv, REG_BT_COEX_TABLE1, 0x55555555); - rtl8xxxu_write32(priv, REG_BT_COEX_TABLE2, 0x55555555); - rtl8xxxu_write32(priv, REG_BT_COEX_TABLE3, 0x00ffffff); - rtl8xxxu_write8(priv, REG_BT_COEX_TABLE4, 0x03); - - memset(&h2c, 0, sizeof(struct h2c_cmd)); - h2c.bt_info.cmd = H2C_8723B_BT_INFO; - h2c.bt_info.data = BIT(0); - rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.bt_info)); - - memset(&h2c, 0, sizeof(struct h2c_cmd)); - h2c.ignore_wlan.cmd = H2C_8723B_BT_IGNORE_WLANACT; - h2c.ignore_wlan.data = 0; - rtl8723a_h2c_cmd(priv, &h2c, sizeof(h2c.ignore_wlan)); -} - void rtl8xxxu_gen2_disable_rf(struct rtl8xxxu_priv *priv) { u32 val32; @@ -6226,48 +4661,6 @@ void rtl8xxxu_gen2_disable_rf(struct rtl8xxxu_priv *priv) rtl8xxxu_write32(priv, REG_RX_WAIT_CCA, val32); } -static void rtl8723bu_init_aggregation(struct rtl8xxxu_priv *priv) -{ - u32 agg_rx; - u8 agg_ctrl; - - /* - * For now simply disable RX aggregation - */ - agg_ctrl = rtl8xxxu_read8(priv, REG_TRXDMA_CTRL); - agg_ctrl &= ~TRXDMA_CTRL_RXDMA_AGG_EN; - - agg_rx = rtl8xxxu_read32(priv, REG_RXDMA_AGG_PG_TH); - agg_rx &= ~RXDMA_USB_AGG_ENABLE; - agg_rx &= ~0xff0f; - - rtl8xxxu_write8(priv, REG_TRXDMA_CTRL, agg_ctrl); - rtl8xxxu_write32(priv, REG_RXDMA_AGG_PG_TH, agg_rx); -} - -static void rtl8723bu_init_statistics(struct rtl8xxxu_priv *priv) -{ - u32 val32; - - /* Time duration for NHM unit: 4us, 0x2710=40ms */ - rtl8xxxu_write16(priv, REG_NHM_TIMER_8723B + 2, 0x2710); - rtl8xxxu_write16(priv, REG_NHM_TH9_TH10_8723B + 2, 0xffff); - rtl8xxxu_write32(priv, REG_NHM_TH3_TO_TH0_8723B, 0xffffff52); - rtl8xxxu_write32(priv, REG_NHM_TH7_TO_TH4_8723B, 0xffffffff); - /* TH8 */ - val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK); - val32 |= 0xff; - rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32); - /* Enable CCK */ - val32 = rtl8xxxu_read32(priv, REG_NHM_TH9_TH10_8723B); - val32 |= BIT(8) | BIT(9) | BIT(10); - rtl8xxxu_write32(priv, REG_NHM_TH9_TH10_8723B, val32); - /* Max power amongst all RX antennas */ - val32 = rtl8xxxu_read32(priv, REG_OFDM0_FA_RSTC); - val32 |= BIT(7); - rtl8xxxu_write32(priv, REG_OFDM0_FA_RSTC, val32); -} - static void rtl8xxxu_old_init_queue_reserved_page(struct rtl8xxxu_priv *priv) { u8 val8; @@ -8459,43 +6852,6 @@ static struct rtl8xxxu_fileops rtl8723au_fops = { .mactable = rtl8xxxu_gen1_mac_init_table, }; -static struct rtl8xxxu_fileops rtl8723bu_fops = { - .parse_efuse = rtl8723bu_parse_efuse, - .load_firmware = rtl8723bu_load_firmware, - .power_on = rtl8723bu_power_on, - .power_off = rtl8723bu_power_off, - .reset_8051 = rtl8723bu_reset_8051, - .llt_init = rtl8xxxu_auto_llt_table, - .init_phy_bb = rtl8723bu_init_phy_bb, - .init_phy_rf = rtl8723bu_init_phy_rf, - .phy_init_antenna_selection = rtl8723bu_phy_init_antenna_selection, - .phy_iq_calibrate = rtl8723bu_phy_iq_calibrate, - .config_channel = rtl8xxxu_gen2_config_channel, - .parse_rx_desc = rtl8xxxu_parse_rxdesc24, - .init_aggregation = rtl8723bu_init_aggregation, - .init_statistics = rtl8723bu_init_statistics, - .enable_rf = rtl8723b_enable_rf, - .disable_rf = rtl8xxxu_gen2_disable_rf, - .usb_quirks = rtl8xxxu_gen2_usb_quirks, - .set_tx_power = rtl8723b_set_tx_power, - .update_rate_mask = rtl8xxxu_gen2_update_rate_mask, - .report_connect = rtl8xxxu_gen2_report_connect, - .writeN_block_size = 1024, - .mbox_ext_reg = REG_HMBOX_EXT0_8723B, - .mbox_ext_width = 4, - .tx_desc_size = sizeof(struct rtl8xxxu_txdesc40), - .rx_desc_size = sizeof(struct rtl8xxxu_rxdesc24), - .has_s0s1 = 1, - .adda_1t_init = 0x01c00014, - .adda_1t_path_on = 0x01c00014, - .adda_2t_path_on_a = 0x01c00014, - .adda_2t_path_on_b = 0x01c00014, - .trxff_boundary = 0x3f7f, - .pbp_rx = PBP_PAGE_SIZE_256, - .pbp_tx = PBP_PAGE_SIZE_256, - .mactable = rtl8723b_mac_init_table, -}; - #ifdef CONFIG_RTL8XXXU_UNTESTED static struct rtl8xxxu_fileops rtl8192cu_fops = {