Merge branch 'sti/dt' into next/drivers

This is apparently a dependency for the STi reset controller driver.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/reset/st,sti-powerdown.txt

@@ -0,0 +1,47 @@
+STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip peripheral controllers such as USB and SATA, using
+"powerdown" control bits found in the STi family SoC system configuration
+registers. These have been grouped together into a single reset controller
+device for convenience.
+
+The actual action taken when powerdown is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "st,<chip>-powerdown"
+	ex: "st,stih415-powerdown", "st,stih416-powerdown"
+- #reset-cells: 1, see below
+
+example:
+
+	powerdown: powerdown-controller {
+		#reset-cells = <1>;
+		compatible = "st,stih415-powerdown";
+	};
+
+
+Specifying powerdown control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the powerdown device node and an
+index specifying which channel to use, as described in reset.txt
+
+example:
+
+	usb1: usb@fe200000 {
+		resets	= <&powerdown STIH41X_USB1_POWERDOWN>;
+	};
+
+Macro definitions for the supported reset channels can be found in:
+
+include/dt-bindings/reset-controller/stih415-resets.h
+include/dt-bindings/reset-controller/stih416-resets.h

Documentation/devicetree/bindings/reset/st,sti-softreset.txt

@@ -0,0 +1,46 @@
+STMicroelectronics STi family Sysconfig Peripheral SoftReset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip peripheral controllers such as USB and SATA, using
+"softreset" control bits found in the STi family SoC system configuration
+registers.
+
+The actual action taken when softreset is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "st,<chip>-softreset" example:
+	"st,stih415-softreset" or "st,stih416-softreset";
+- #reset-cells: 1, see below
+
+example:
+
+	softreset: softreset-controller {
+		#reset-cells = <1>;
+		compatible = "st,stih415-softreset";
+	};
+
+
+Specifying softreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the softreset device node and an
+index specifying which channel to use, as described in reset.txt
+
+example:
+
+	ethernet0{
+		resets			= <&softreset STIH415_ETH0_SOFTRESET>;
+	};
+
+Macro definitions for the supported reset channels can be found in:
+
+include/dt-bindings/reset-controller/stih415-resets.h
+include/dt-bindings/reset-controller/stih416-resets.h

arch/arm/boot/dts/stih415-clock.dtsi

@@ -34,5 +34,19 @@
 			compatible = "fixed-clock";
 			clock-frequency = <100000000>;
 		};
+
+		CLKS_GMAC0_PHY: clockgenA1@7 {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <25000000>;
+			clock-output-names = "CLKS_GMAC0_PHY";
+		};
+
+		CLKS_ETH1_PHY: clockgenA0@7 {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <25000000>;
+			clock-output-names = "CLKS_ETH1_PHY";
+		};
 	};
 };

arch/arm/boot/dts/stih415-pinctrl.dtsi

@@ -7,6 +7,7 @@
  * publishhed by the Free Software Foundation.
  */
 #include "st-pincfg.h"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 / {
 
 	aliases {
@@ -45,35 +46,49 @@
 			#size-cells	= <1>;
 			compatible	= "st,stih415-sbc-pinctrl";
 			st,syscfg	= <&syscfg_sbc>;
+			reg 		= <0xfe61f080 0x4>;
+			reg-names	= "irqmux";
+			interrupts 	= <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-names = "irqmux";
 			ranges 		= <0 0xfe610000 0x5000>;
 
 			PIO0: gpio@fe610000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0 0x100>;
 				st,bank-name	= "PIO0";
 			};
 			PIO1: gpio@fe611000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x1000 0x100>;
 				st,bank-name	= "PIO1";
 			};
 			PIO2: gpio@fe612000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x2000 0x100>;
 				st,bank-name	= "PIO2";
 			};
 			PIO3: gpio@fe613000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x3000 0x100>;
 				st,bank-name	= "PIO3";
 			};
 			PIO4: gpio@fe614000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x4000 0x100>;
 				st,bank-name	= "PIO4";
 			};
@@ -104,6 +119,64 @@
 					};
 				};
 			};
+
+			rc{
+				pinctrl_ir: ir0 {
+					st,pins {
+						ir = <&PIO4 0 ALT2 IN>;
+					};
+				};
+			};
+
+			gmac1 {
+				pinctrl_mii1: mii1 {
+						st,pins {
+						 txd0   = <&PIO0 0 ALT1 OUT  SE_NICLK_IO	0	CLK_A>;
+						 txd1   = <&PIO0 1 ALT1 OUT  SE_NICLK_IO	0	CLK_A>;
+						 txd2   = <&PIO0 2 ALT1 OUT  SE_NICLK_IO	0	CLK_A>;
+						 txd3   = <&PIO0 3 ALT1 OUT  SE_NICLK_IO	0	CLK_A>;
+						 txer   = <&PIO0 4 ALT1 OUT  SE_NICLK_IO	0	CLK_A>;
+						 txen   = <&PIO0 5 ALT1 OUT  SE_NICLK_IO	0	CLK_A>;
+						 txclk  = <&PIO0 6 ALT1 IN   NICLK	0	CLK_A>;
+						 col    = <&PIO0 7 ALT1 IN   BYPASS	1000>;
+						 mdio   = <&PIO1 0 ALT1 OUT  BYPASS	0>;
+						 mdc    = <&PIO1 1 ALT1 OUT  NICLK	0	CLK_A>;
+						 crs    = <&PIO1 2 ALT1 IN   BYPASS	1000>;
+						 mdint  = <&PIO1 3 ALT1 IN   BYPASS	0>;
+						 rxd0   = <&PIO1 4 ALT1 IN   SE_NICLK_IO	0	CLK_A>;
+						 rxd1   = <&PIO1 5 ALT1 IN   SE_NICLK_IO	0	CLK_A>;
+						 rxd2   = <&PIO1 6 ALT1 IN   SE_NICLK_IO	0	CLK_A>;
+						 rxd3   = <&PIO1 7 ALT1 IN   SE_NICLK_IO	0	CLK_A>;
+						 rxdv   = <&PIO2 0 ALT1 IN   SE_NICLK_IO	0	CLK_A>;
+						 rx_er  = <&PIO2 1 ALT1 IN   SE_NICLK_IO	0	CLK_A>;
+						 rxclk  = <&PIO2 2 ALT1 IN   NICLK	0	CLK_A>;
+						 phyclk = <&PIO2 3 ALT1 IN   NICLK	1000	CLK_A>;
+					};
+				};
+
+				pinctrl_rgmii1: rgmii1-0 {
+					st,pins {
+						 txd0 =	 <&PIO0 0 ALT1 OUT DE_IO	1000	CLK_A>;
+						 txd1 =	 <&PIO0 1 ALT1 OUT DE_IO	1000	CLK_A>;
+						 txd2 =	 <&PIO0 2 ALT1 OUT DE_IO	1000	CLK_A>;
+						 txd3 =	 <&PIO0 3 ALT1 OUT DE_IO	1000	CLK_A>;
+						 txen =	 <&PIO0 5 ALT1 OUT DE_IO	0	CLK_A>;
+						 txclk = <&PIO0 6 ALT1 IN	NICLK	0	CLK_A>;
+						 mdio =	 <&PIO1 0 ALT1 OUT	BYPASS	0>;
+						 mdc =	 <&PIO1 1 ALT1 OUT	NICLK	0	CLK_A>;
+						 rxd0 =	 <&PIO1 4 ALT1 IN DE_IO	0	CLK_A>;
+						 rxd1 =	 <&PIO1 5 ALT1 IN DE_IO	0	CLK_A>;
+						 rxd2 =	 <&PIO1 6 ALT1 IN DE_IO	0	CLK_A>;
+						 rxd3 =	 <&PIO1 7 ALT1 IN DE_IO	0	CLK_A>;
+
+						 rxdv =	  <&PIO2 0 ALT1 IN DE_IO	500	CLK_A>;
+						 rxclk =  <&PIO2 2 ALT1 IN	NICLK	0	CLK_A>;
+						 phyclk = <&PIO2 3 ALT4 OUT	NICLK	0	CLK_B>;
+
+						 clk125= <&PIO3 7 ALT4 IN 	NICLK	0	CLK_A>;
+					};
+				};
+			};
 		};
 
 		pin-controller-front {
@@ -111,53 +184,73 @@
 			#size-cells	= <1>;
 			compatible	= "st,stih415-front-pinctrl";
 			st,syscfg	= <&syscfg_front>;
+			reg 		= <0xfee0f080 0x4>;
+			reg-names	= "irqmux";
+			interrupts 	= <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-names = "irqmux";
 			ranges		= <0 0xfee00000 0x8000>;
 
 			PIO5: gpio@fee00000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0 0x100>;
 				st,bank-name	= "PIO5";
 			};
 			PIO6: gpio@fee01000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x1000 0x100>;
 				st,bank-name	= "PIO6";
 			};
 			PIO7: gpio@fee02000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x2000 0x100>;
 				st,bank-name	= "PIO7";
 			};
 			PIO8: gpio@fee03000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x3000 0x100>;
 				st,bank-name	= "PIO8";
 			};
 			PIO9: gpio@fee04000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x4000 0x100>;
 				st,bank-name	= "PIO9";
 			};
 			PIO10: gpio@fee05000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x5000 0x100>;
 				st,bank-name	= "PIO10";
 			};
 			PIO11: gpio@fee06000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x6000 0x100>;
 				st,bank-name	= "PIO11";
 			};
 			PIO12: gpio@fee07000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x7000 0x100>;
 				st,bank-name	= "PIO12";
 			};
@@ -186,41 +279,57 @@
 			#size-cells	= <1>;
 			compatible	= "st,stih415-rear-pinctrl";
 			st,syscfg	= <&syscfg_rear>;
+			reg 		= <0xfe82f080 0x4>;
+			reg-names	= "irqmux";
+			interrupts 	= <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-names = "irqmux";
 			ranges		= <0 0xfe820000 0x8000>;
 
 			PIO13: gpio@fe820000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0 0x100>;
 				st,bank-name	= "PIO13";
 			};
 			PIO14: gpio@fe821000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x1000 0x100>;
 				st,bank-name	= "PIO14";
 			};
 			PIO15: gpio@fe822000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x2000 0x100>;
 				st,bank-name	= "PIO15";
 			};
 			PIO16: gpio@fe823000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x3000 0x100>;
 				st,bank-name	= "PIO16";
 			};
 			PIO17: gpio@fe824000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x4000 0x100>;
 				st,bank-name	= "PIO17";
 			};
 			PIO18: gpio@fe825000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x5000 0x100>;
 				st,bank-name	= "PIO18";
 			};
@@ -233,6 +342,77 @@
 					};
 				};
 			};
+
+			gmac0{
+				pinctrl_mii0: mii0 {
+					st,pins {
+					 mdint =	<&PIO13 6 ALT2	IN	BYPASS		0>;
+					 txen =		<&PIO13 7 ALT2	OUT	SE_NICLK_IO	0	CLK_A>;
+
+					 txd0 =		<&PIO14 0 ALT2	OUT	SE_NICLK_IO	0	CLK_A>;
+					 txd1 =		<&PIO14 1 ALT2	OUT	SE_NICLK_IO	0	CLK_A>;
+					 txd2 =		<&PIO14 2 ALT2	OUT	SE_NICLK_IO	0	CLK_B>;
+					 txd3 =		<&PIO14 3 ALT2	OUT	SE_NICLK_IO	0	CLK_B>;
+
+					 txclk =	<&PIO15 0 ALT2	IN	NICLK		0	CLK_A>;
+					 txer =		<&PIO15 1 ALT2	OUT	SE_NICLK_IO	0	CLK_A>;
+					 crs =		<&PIO15 2 ALT2	IN	BYPASS		1000>;
+					 col =		<&PIO15 3 ALT2	IN	BYPASS		1000>;
+					 mdio  =        <&PIO15 4 ALT2	OUT	BYPASS 	3000>;
+					 mdc   =        <&PIO15 5 ALT2	OUT     NICLK  	0    	CLK_B>;
+
+					 rxd0 =		<&PIO16 0 ALT2	IN	SE_NICLK_IO	0	CLK_A>;
+					 rxd1 =		<&PIO16 1 ALT2	IN	SE_NICLK_IO	0	CLK_A>;
+					 rxd2 =		<&PIO16 2 ALT2	IN	SE_NICLK_IO	0	CLK_A>;
+					 rxd3 =		<&PIO16 3 ALT2	IN	SE_NICLK_IO	0	CLK_A>;
+					 rxdv =		<&PIO15 6 ALT2	IN	SE_NICLK_IO	0	CLK_A>;
+					 rx_er =	<&PIO15 7 ALT2	IN	SE_NICLK_IO	0	CLK_A>;
+					 rxclk =	<&PIO17 0 ALT2	IN	NICLK		0	CLK_A>;
+					 phyclk =	<&PIO13 5 ALT2	OUT	NICLK	1000	CLK_A>;
+
+					};
+				};
+
+			pinctrl_gmii0: gmii0 {
+				st,pins {
+					 mdint =	<&PIO13 6	ALT2 IN		BYPASS	0>;
+					 mdio  =        <&PIO15 4 	ALT2 OUT	BYPASS 	3000>;
+					 mdc   =        <&PIO15 5 	ALT2 OUT    	NICLK  	0    	CLK_B>;
+					 txen =		<&PIO13 7	ALT2 OUT	SE_NICLK_IO	3000	CLK_A>;
+
+					 txd0 =		<&PIO14 0	ALT2 OUT	SE_NICLK_IO	3000	CLK_A>;
+					 txd1 =		<&PIO14 1	ALT2 OUT	SE_NICLK_IO	3000	CLK_A>;
+					 txd2 =		<&PIO14 2	ALT2 OUT	SE_NICLK_IO	3000	CLK_B>;
+					 txd3 =		<&PIO14 3	ALT2 OUT	SE_NICLK_IO	3000	CLK_B>;
+					 txd4 =		<&PIO14 4	ALT2 OUT	SE_NICLK_IO	3000	CLK_B>;
+					 txd5 =		<&PIO14 5	ALT2 OUT	SE_NICLK_IO	3000	CLK_B>;
+					 txd6 =		<&PIO14 6	ALT2 OUT	SE_NICLK_IO	3000	CLK_B>;
+					 txd7 =		<&PIO14 7	ALT2 OUT	SE_NICLK_IO	3000	CLK_B>;
+
+					 txclk =	<&PIO15 0	ALT2 IN		NICLK	0	CLK_A>;
+					 txer =		<&PIO15 1	ALT2 OUT 	SE_NICLK_IO	3000	CLK_A>;
+					 crs =		<&PIO15 2	ALT2 IN		BYPASS	1000>;
+					 col =		<&PIO15 3	ALT2 IN		BYPASS	1000>;
+					 rxdv =		<&PIO15 6	ALT2 IN		SE_NICLK_IO	1500	CLK_A>;
+					 rx_er =	<&PIO15 7	ALT2 IN		SE_NICLK_IO	1500	CLK_A>;
+
+					 rxd0 =		<&PIO16 0	ALT2 IN		SE_NICLK_IO	1500	CLK_A>;
+					 rxd1 =		<&PIO16 1	ALT2 IN		SE_NICLK_IO	1500	CLK_A>;
+					 rxd2 =		<&PIO16 2	ALT2 IN		SE_NICLK_IO	1500	CLK_A>;
+					 rxd3 =		<&PIO16 3	ALT2 IN		SE_NICLK_IO	1500	CLK_A>;
+					 rxd4 =		<&PIO16 4	ALT2 IN		SE_NICLK_IO	1500	CLK_A>;
+					 rxd5 =		<&PIO16 5	ALT2 IN		SE_NICLK_IO	1500	CLK_A>;
+					 rxd6 =		<&PIO16 6	ALT2 IN		SE_NICLK_IO	1500	CLK_A>;
+					 rxd7 =		<&PIO16 7	ALT2 IN		SE_NICLK_IO	1500	CLK_A>;
+
+					 rxclk =	<&PIO17 0	ALT2 IN	NICLK	0	CLK_A>;
+					 clk125 =	<&PIO17 6	ALT1 IN	NICLK	0	CLK_A>;
+                                         phyclk =       <&PIO13 5       ALT4 OUT NICLK   0       CLK_B>;
+
+
+					};
+				};
+			};
 		};
 
 		pin-controller-left {
@@ -240,23 +420,33 @@
 			#size-cells	= <1>;
 			compatible	= "st,stih415-left-pinctrl";
 			st,syscfg	= <&syscfg_left>;
+			reg 		= <0xfd6bf080 0x4>;
+			reg-names	= "irqmux";
+			interrupts 	= <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-names = "irqmux";
 			ranges		= <0 0xfd6b0000 0x3000>;
 
 			PIO100: gpio@fd6b0000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0 0x100>;
 				st,bank-name	= "PIO100";
 			};
 			PIO101: gpio@fd6b1000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x1000 0x100>;
 				st,bank-name	= "PIO101";
 			};
 			PIO102: gpio@fd6b2000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x2000 0x100>;
 				st,bank-name	= "PIO102";
 			};
@@ -267,35 +457,49 @@
 			#size-cells	= <1>;
 			compatible	= "st,stih415-right-pinctrl";
 			st,syscfg	= <&syscfg_right>;
+			reg 		= <0xfd33f080 0x4>;
+			reg-names	= "irqmux";
+			interrupts 	= <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-names = "irqmux";
 			ranges		= <0 0xfd330000 0x5000>;
 
 			PIO103: gpio@fd330000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0 0x100>;
 				st,bank-name	= "PIO103";
 			};
 			PIO104: gpio@fd331000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x1000 0x100>;
 				st,bank-name	= "PIO104";
 			};
 			PIO105: gpio@fd332000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x2000 0x100>;
 				st,bank-name	= "PIO105";
 			};
 			PIO106: gpio@fd333000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x3000 0x100>;
 				st,bank-name	= "PIO106";
 			};
 			PIO107: gpio@fd334000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x4000 0x100>;
 				st,bank-name	= "PIO107";
 			};

arch/arm/boot/dts/stih415.dtsi

@@ -10,6 +10,7 @@
 #include "stih415-clock.dtsi"
 #include "stih415-pinctrl.dtsi"
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset-controller/stih415-resets.h>
 / {
 
 	L2: cache-controller {
@@ -28,6 +29,16 @@
 		ranges;
 		compatible	= "simple-bus";
 
+		powerdown: powerdown-controller {
+			#reset-cells = <1>;
+			compatible = "st,stih415-powerdown";
+		};
+
+		softreset: softreset-controller {
+			#reset-cells = <1>;
+			compatible = "st,stih415-softreset";
+		};
+
 		syscfg_sbc: sbc-syscfg@fe600000{
 			compatible      = "st,stih415-sbc-syscfg", "syscon";
 			reg		= <0xfe600000 0xb4>;
@@ -136,5 +147,64 @@
 
 			status		= "disabled";
 		};
+
+		ethernet0: dwmac@fe810000 {
+			device_type 	= "network";
+			compatible	= "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610";
+			status 		= "disabled";
+
+			reg 		= <0xfe810000 0x8000>, <0x148 0x4>;
+			reg-names	= "stmmaceth", "sti-ethconf";
+
+			interrupts 	= <0 147 0>, <0 148 0>, <0 149 0>;
+			interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+			resets			= <&softreset STIH415_ETH0_SOFTRESET>;
+			reset-names		= "stmmaceth";
+
+			snps,pbl 	= <32>;
+			snps,mixed-burst;
+			snps,force_sf_dma_mode;
+
+			st,syscon	= <&syscfg_rear>;
+
+			pinctrl-names 	= "default";
+			pinctrl-0	= <&pinctrl_mii0>;
+			clock-names	= "stmmaceth";
+			clocks		= <&CLKS_GMAC0_PHY>;
+		};
+
+		ethernet1: dwmac@fef08000 {
+			device_type = "network";
+			compatible	= "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610";
+			status 		= "disabled";
+			reg		= <0xfef08000 0x8000>, <0x74 0x4>;
+			reg-names	= "stmmaceth", "sti-ethconf";
+			interrupts 	= <0 150 0>, <0 151 0>, <0 152 0>;
+			interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+			snps,pbl	= <32>;
+			snps,mixed-burst;
+			snps,force_sf_dma_mode;
+
+			st,syscon		= <&syscfg_sbc>;
+
+			resets			= <&softreset STIH415_ETH1_SOFTRESET>;
+			reset-names		= "stmmaceth";
+			pinctrl-names 	= "default";
+			pinctrl-0	= <&pinctrl_mii1>;
+			clock-names	= "stmmaceth";
+			clocks		= <&CLKS_ETH1_PHY>;
+		};
+
+		rc: rc@fe518000 {
+			compatible	= "st,comms-irb";
+			reg		= <0xfe518000 0x234>;
+			interrupts	=  <0 203 0>;
+			clocks		= <&CLK_SYSIN>;
+			rx-mode		= "infrared";
+			pinctrl-names 	= "default";
+			pinctrl-0	= <&pinctrl_ir>;
+			resets		= <&softreset STIH415_IRB_SOFTRESET>;
+		};
 	};
 };

arch/arm/boot/dts/stih416-clock.dtsi

@@ -37,5 +37,19 @@
 			clock-frequency = <100000000>;
 			clock-output-names = "CLK_S_ICN_REG_0";
 		};
+
+		CLK_S_GMAC0_PHY: clockgenA1@7 {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <25000000>;
+			clock-output-names = "CLK_S_GMAC0_PHY";
+		};
+
+		CLK_S_ETH1_PHY: clockgenA0@7 {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <25000000>;
+			clock-output-names = "CLK_S_ETH1_PHY";
+		};
 	};
 };

arch/arm/boot/dts/stih416-pinctrl.dtsi

@@ -8,6 +8,7 @@
  * publishhed by the Free Software Foundation.
  */
 #include "st-pincfg.h"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 / {
 
 	aliases {
@@ -49,46 +50,69 @@
 			#size-cells	= <1>;
 			compatible	= "st,stih416-sbc-pinctrl";
 			st,syscfg	= <&syscfg_sbc>;
+			reg 		= <0xfe61f080 0x4>;
+			reg-names	= "irqmux";
+			interrupts 	= <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-names = "irqmux";
 			ranges		= <0 0xfe610000 0x6000>;
 
 			PIO0: gpio@fe610000 {
 				gpio-controller;
 				#gpio-cells = <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0 0x100>;
 				st,bank-name	= "PIO0";
 			};
 			PIO1: gpio@fe611000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x1000 0x100>;
 				st,bank-name	= "PIO1";
 			};
 			PIO2: gpio@fe612000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x2000 0x100>;
 				st,bank-name	= "PIO2";
 			};
 			PIO3: gpio@fe613000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x3000 0x100>;
 				st,bank-name	= "PIO3";
 			};
 			PIO4: gpio@fe614000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x4000 0x100>;
 				st,bank-name	= "PIO4";
 			};
 			PIO40: gpio@fe615000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x5000 0x100>;
 				st,bank-name	= "PIO40";
 				st,retime-pin-mask = <0x7f>;
 			};
 
+			rc{
+				pinctrl_ir: ir0 {
+					st,pins {
+						ir = <&PIO4 0 ALT2 IN>;
+					};
+				};
+			};
 			sbc_serial1 {
 				pinctrl_sbc_serial1: sbc_serial1 {
 					st,pins {
@@ -115,6 +139,58 @@
 					};
 				};
 			};
+
+			gmac1 {
+				pinctrl_mii1: mii1 {
+					st,pins {
+						txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>;
+						txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>;
+						col =   <&PIO0 7 ALT1 IN BYPASS 1000>;
+
+						mdio =  <&PIO1 0 ALT1 OUT BYPASS 1500>;
+						mdc =   <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>;
+						crs =   <&PIO1 2 ALT1 IN BYPASS 1000>;
+						mdint = <&PIO1 3 ALT1 IN BYPASS 0>;
+						rxd0 =  <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						rxd1 =  <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						rxd2 =  <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						rxd3 =  <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+
+						rxdv =  <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>;
+						rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>;
+						phyclk = <&PIO2 3 ALT1 OUT NICLK 0 CLK_A>;
+					};
+				};
+				pinctrl_rgmii1: rgmii1-0 {
+					st,pins {
+						txd0 =  <&PIO0 0 ALT1 OUT DE_IO 500 CLK_A>;
+						txd1 =  <&PIO0 1 ALT1 OUT DE_IO 500 CLK_A>;
+						txd2 =  <&PIO0 2 ALT1 OUT DE_IO 500 CLK_A>;
+						txd3 =  <&PIO0 3 ALT1 OUT DE_IO 500 CLK_A>;
+						txen =  <&PIO0 5 ALT1 OUT DE_IO 0   CLK_A>;
+						txclk = <&PIO0 6 ALT1 IN  NICLK 0   CLK_A>;
+
+						mdio = <&PIO1 0 ALT1 OUT BYPASS 0>;
+						mdc  = <&PIO1 1 ALT1 OUT NICLK  0 CLK_A>;
+						rxd0 = <&PIO1 4 ALT1 IN DE_IO 500 CLK_A>;
+						rxd1 = <&PIO1 5 ALT1 IN DE_IO 500 CLK_A>;
+						rxd2 = <&PIO1 6 ALT1 IN DE_IO 500 CLK_A>;
+						rxd3 = <&PIO1 7 ALT1 IN DE_IO 500 CLK_A>;
+
+						rxdv   = <&PIO2 0 ALT1 IN  DE_IO 500 CLK_A>;
+						rxclk  = <&PIO2 2 ALT1 IN  NICLK 0   CLK_A>;
+						phyclk = <&PIO2 3 ALT4 OUT NICLK 0   CLK_B>;
+
+						clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>;
+					};
+				};
+			};
 		};
 
 		pin-controller-front {
@@ -122,65 +198,89 @@
 			#size-cells	= <1>;
 			compatible	= "st,stih416-front-pinctrl";
 			st,syscfg	= <&syscfg_front>;
+			reg 		= <0xfee0f080 0x4>;
+			reg-names	= "irqmux";
+			interrupts 	= <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-names = "irqmux";
 			ranges		= <0 0xfee00000 0x10000>;
 
 			PIO5: gpio@fee00000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0 0x100>;
 				st,bank-name	= "PIO5";
 			};
 			PIO6: gpio@fee01000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x1000 0x100>;
 				st,bank-name	= "PIO6";
 			};
 			PIO7: gpio@fee02000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x2000 0x100>;
 				st,bank-name	= "PIO7";
 			};
 			PIO8: gpio@fee03000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x3000 0x100>;
 				st,bank-name	= "PIO8";
 			};
 			PIO9: gpio@fee04000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x4000 0x100>;
 				st,bank-name	= "PIO9";
 			};
 			PIO10: gpio@fee05000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x5000 0x100>;
 				st,bank-name	= "PIO10";
 			};
 			PIO11: gpio@fee06000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x6000 0x100>;
 				st,bank-name	= "PIO11";
 			};
 			PIO12: gpio@fee07000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x7000 0x100>;
 				st,bank-name	= "PIO12";
 			};
 			PIO30: gpio@fee08000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x8000 0x100>;
 				st,bank-name	= "PIO30";
 			};
 			PIO31: gpio@fee09000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x9000 0x100>;
 				st,bank-name	= "PIO31";
 			};
@@ -217,41 +317,57 @@
 			#size-cells	= <1>;
 			compatible	= "st,stih416-rear-pinctrl";
 			st,syscfg	= <&syscfg_rear>;
+			reg 		= <0xfe82f080 0x4>;
+			reg-names	= "irqmux";
+			interrupts 	= <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-names = "irqmux";
 			ranges 		= <0 0xfe820000 0x6000>;
 
 			PIO13: gpio@fe820000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0 0x100>;
 				st,bank-name	= "PIO13";
 			};
 			PIO14: gpio@fe821000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x1000 0x100>;
 				st,bank-name	= "PIO14";
 			};
 			PIO15: gpio@fe822000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x2000 0x100>;
 				st,bank-name	= "PIO15";
 			};
 			PIO16: gpio@fe823000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x3000 0x100>;
 				st,bank-name	= "PIO16";
 			};
 			PIO17: gpio@fe824000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x4000 0x100>;
 				st,bank-name	= "PIO17";
 			};
 			PIO18: gpio@fe825000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x5000 0x100>;
 				st,bank-name	= "PIO18";
 				st,retime-pin-mask = <0xf>;
@@ -265,6 +381,63 @@
 					};
 				};
 			};
+
+			gmac0 {
+				pinctrl_mii0: mii0 {
+					st,pins {
+						mdint = <&PIO13 6 ALT2 IN  BYPASS      0>;
+						txen =  <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+						txd0 =  <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+						txd1 =  <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+						txd2 =  <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+						txd3 =  <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>;
+
+						txclk = <&PIO15 0 ALT2 IN  NICLK       0 CLK_A>;
+						txer =  <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>;
+						crs = <&PIO15 2 ALT2 IN  BYPASS 1000>;
+						col = <&PIO15 3 ALT2 IN  BYPASS 1000>;
+						mdio= <&PIO15 4 ALT2 OUT BYPASS 1500>;
+						mdc = <&PIO15 5 ALT2 OUT NICLK  0    CLK_B>;
+
+						rxd0 =  <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						rxd1 =  <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						rxd2 =  <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						rxd3 =  <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						rxdv =  <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>;
+						rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+						phyclk = <&PIO13 5 ALT2 OUT NICLK 0 CLK_B>;
+					};
+				};
+
+				pinctrl_gmii0: gmii0 {
+					st,pins {
+						};
+				};
+				pinctrl_rgmii0: rgmii0 {
+					st,pins {
+						 phyclk = <&PIO13  5 ALT4 OUT NICLK 0 CLK_B>;
+						 txen = <&PIO13 7 ALT2 OUT DE_IO 0 CLK_A>;
+						 txd0  = <&PIO14 0 ALT2 OUT DE_IO 500 CLK_A>;
+						 txd1  = <&PIO14 1 ALT2 OUT DE_IO 500 CLK_A>;
+						 txd2  = <&PIO14 2 ALT2 OUT DE_IO 500 CLK_B>;
+						 txd3  = <&PIO14 3 ALT2 OUT DE_IO 500 CLK_B>;
+						 txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>;
+
+						 mdio = <&PIO15 4 ALT2 OUT BYPASS 0>;
+						 mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>;
+
+						 rxdv = <&PIO15 6 ALT2 IN DE_IO 500 CLK_A>;
+						 rxd0 =<&PIO16 0 ALT2 IN DE_IO	500 CLK_A>;
+						 rxd1 =<&PIO16 1 ALT2 IN DE_IO	500 CLK_A>;
+						 rxd2 =<&PIO16 2 ALT2 IN DE_IO	500 CLK_A>;
+						 rxd3  =<&PIO16 3 ALT2 IN DE_IO 500 CLK_A>;
+						 rxclk =<&PIO17 0 ALT2 IN NICLK 0 CLK_A>;
+
+						 clk125=<&PIO17 6 ALT1 IN NICLK 0 CLK_A>;
+					};
+				};
+			};
 		};
 
 		pin-controller-fvdp-fe {
@@ -272,23 +445,33 @@
 			#size-cells	= <1>;
 			compatible	= "st,stih416-fvdp-fe-pinctrl";
 			st,syscfg	= <&syscfg_fvdp_fe>;
+			reg 		= <0xfd6bf080 0x4>;
+			reg-names	= "irqmux";
+			interrupts 	= <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-names = "irqmux";
 			ranges		= <0 0xfd6b0000 0x3000>;
 
 			PIO100: gpio@fd6b0000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0 0x100>;
 				st,bank-name	= "PIO100";
 			};
 			PIO101: gpio@fd6b1000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x1000 0x100>;
 				st,bank-name	= "PIO101";
 			};
 			PIO102: gpio@fd6b2000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x2000 0x100>;
 				st,bank-name	= "PIO102";
 			};
@@ -299,29 +482,41 @@
 			#size-cells	= <1>;
 			compatible	= "st,stih416-fvdp-lite-pinctrl";
 			st,syscfg		= <&syscfg_fvdp_lite>;
+			reg 		= <0xfd33f080 0x4>;
+			reg-names	= "irqmux";
+			interrupts 	= <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-names = "irqmux";
 			ranges			= <0 0xfd330000 0x5000>;
 
 			PIO103: gpio@fd330000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0 0x100>;
 				st,bank-name	= "PIO103";
 			};
 			PIO104: gpio@fd331000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x1000 0x100>;
 				st,bank-name	= "PIO104";
 			};
 			PIO105: gpio@fd332000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x2000 0x100>;
 				st,bank-name	= "PIO105";
 			};
 			PIO106: gpio@fd333000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x3000 0x100>;
 				st,bank-name	= "PIO106";
 			};
@@ -329,6 +524,8 @@
 			PIO107: gpio@fd334000 {
 				gpio-controller;
 				#gpio-cells	= <1>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 				reg		= <0x4000 0x100>;
 				st,bank-name	= "PIO107";
 				st,retime-pin-mask = <0xf>;

arch/arm/boot/dts/stih416.dtsi

@@ -10,6 +10,7 @@
 #include "stih416-clock.dtsi"
 #include "stih416-pinctrl.dtsi"
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset-controller/stih416-resets.h>
 / {
 	L2: cache-controller {
 		compatible = "arm,pl310-cache";
@@ -27,6 +28,16 @@
 		ranges;
 		compatible	= "simple-bus";
 
+		powerdown: powerdown-controller {
+			#reset-cells = <1>;
+			compatible = "st,stih416-powerdown";
+		};
+
+		softreset: softreset-controller {
+			#reset-cells = <1>;
+			compatible = "st,stih416-softreset";
+		};
+
 		syscfg_sbc:sbc-syscfg@fe600000{
 			compatible	= "st,stih416-sbc-syscfg", "syscon";
 			reg		= <0xfe600000 0x1000>;
@@ -145,5 +156,61 @@
 
 			status		= "disabled";
 		};
+
+		ethernet0: dwmac@fe810000 {
+			device_type 	= "network";
+			compatible	= "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+			status 		= "disabled";
+			reg 		= <0xfe810000 0x8000>, <0x8bc 0x4>;
+			reg-names	= "stmmaceth", "sti-ethconf";
+
+			interrupts = <0 133 0>, <0 134 0>, <0 135 0>;
+			interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+			snps,pbl 	= <32>;
+			snps,mixed-burst;
+
+			st,syscon		= <&syscfg_rear>;
+			resets			= <&softreset STIH416_ETH0_SOFTRESET>;
+			reset-names		= "stmmaceth";
+			pinctrl-names 	= "default";
+			pinctrl-0	= <&pinctrl_mii0>;
+			clock-names	= "stmmaceth";
+			clocks		= <&CLK_S_GMAC0_PHY>;
+		};
+
+		ethernet1: dwmac@fef08000 {
+			device_type = "network";
+			compatible		= "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+			status 		= "disabled";
+			reg		= <0xfef08000 0x8000>, <0x7f0 0x4>;
+			reg-names	= "stmmaceth", "sti-ethconf";
+			interrupts = <0 136 0>, <0 137 0>, <0 138 0>;
+			interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+			snps,pbl	= <32>;
+			snps,mixed-burst;
+
+			st,syscon	= <&syscfg_sbc>;
+
+			resets		= <&softreset STIH416_ETH1_SOFTRESET>;
+			reset-names	= "stmmaceth";
+			pinctrl-names 	= "default";
+			pinctrl-0	= <&pinctrl_mii1>;
+			clock-names	= "stmmaceth";
+			clocks		= <&CLK_S_ETH1_PHY>;
+		};
+
+		rc: rc@fe518000 {
+			compatible	= "st,comms-irb";
+			reg		= <0xfe518000 0x234>;
+			interrupts	=  <0 203 0>;
+			rx-mode         = "infrared";
+			clocks		= <&CLK_SYSIN>;
+			pinctrl-names 	= "default";
+			pinctrl-0	= <&pinctrl_ir>;
+			resets		= <&softreset STIH416_IRB_SOFTRESET>;
+		};
+
 	};
 };

arch/arm/boot/dts/stih41x-b2000.dtsi

@@ -20,6 +20,8 @@
 
 	aliases {
 		ttyAS0 = &serial2;
+		ethernet0 = &ethernet0;
+		ethernet1 = &ethernet1;
 	};
 
 	soc {
@@ -46,5 +48,25 @@
 
 			status = "okay";
 		};
+
+		ethernet0: dwmac@fe810000 {
+			status			= "okay";
+			phy-mode		= "mii";
+			pinctrl-0		= <&pinctrl_mii0>;
+
+			snps,reset-gpio 	= <&PIO106 2>;
+			snps,reset-active-low;
+			snps,reset-delays-us 	= <0 10000 10000>;
+		};
+
+		ethernet1: dwmac@fef08000 {
+			status			= "disabled";
+			phy-mode		= "mii";
+			st,tx-retime-src	= "txclk";
+
+			snps,reset-gpio 	= <&PIO4 7>;
+			snps,reset-active-low;
+			snps,reset-delays-us 	= <0 10000 10000>;
+		};
 	};
 };

arch/arm/boot/dts/stih41x-b2020.dtsi

@@ -19,6 +19,7 @@
 
 	aliases {
 		ttyAS0 = &sbc_serial1;
+		ethernet1 = &ethernet1;
 	};
 	soc {
 		sbc_serial1: serial@fe531000 {
@@ -60,5 +61,17 @@
 		i2c@fe541000 {
 			status = "okay";
 		};
+
+		ethernet1: dwmac@fef08000 {
+			status			= "okay";
+			phy-mode		= "rgmii-id";
+			max-speed		= <1000>;
+			st,tx-retime-src	= "clk_125";
+			snps,reset-gpio 	= <&PIO3 0>;
+			snps,reset-active-low;
+			snps,reset-delays-us 	= <0 10000 10000>;
+
+			pinctrl-0	= <&pinctrl_rgmii1>;
+		};
 	};
 };

include/dt-bindings/reset-controller/stih415-resets.h

@@ -0,0 +1,26 @@
+/*
+ * This header provides constants for the reset controller
+ * based peripheral powerdown requests on the STMicroelectronics
+ * STiH415 SoC.
+ */
+#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH415
+#define _DT_BINDINGS_RESET_CONTROLLER_STIH415
+
+#define STIH415_EMISS_POWERDOWN		0
+#define STIH415_NAND_POWERDOWN		1
+#define STIH415_KEYSCAN_POWERDOWN	2
+#define STIH415_USB0_POWERDOWN		3
+#define STIH415_USB1_POWERDOWN		4
+#define STIH415_USB2_POWERDOWN		5
+#define STIH415_SATA0_POWERDOWN		6
+#define STIH415_SATA1_POWERDOWN		7
+#define STIH415_PCIE_POWERDOWN		8
+
+#define STIH415_ETH0_SOFTRESET		0
+#define STIH415_ETH1_SOFTRESET		1
+#define STIH415_IRB_SOFTRESET		2
+#define STIH415_USB0_SOFTRESET		3
+#define STIH415_USB1_SOFTRESET		4
+#define STIH415_USB2_SOFTRESET		5
+
+#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH415 */

include/dt-bindings/reset-controller/stih416-resets.h

@@ -0,0 +1,50 @@
+/*
+ * This header provides constants for the reset controller
+ * based peripheral powerdown requests on the STMicroelectronics
+ * STiH416 SoC.
+ */
+#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH416
+#define _DT_BINDINGS_RESET_CONTROLLER_STIH416
+
+#define STIH416_EMISS_POWERDOWN		0
+#define STIH416_NAND_POWERDOWN		1
+#define STIH416_KEYSCAN_POWERDOWN	2
+#define STIH416_USB0_POWERDOWN		3
+#define STIH416_USB1_POWERDOWN		4
+#define STIH416_USB2_POWERDOWN		5
+#define STIH416_USB3_POWERDOWN		6
+#define STIH416_SATA0_POWERDOWN		7
+#define STIH416_SATA1_POWERDOWN		8
+#define STIH416_PCIE0_POWERDOWN		9
+#define STIH416_PCIE1_POWERDOWN		10
+
+#define STIH416_ETH0_SOFTRESET		0
+#define STIH416_ETH1_SOFTRESET		1
+#define STIH416_IRB_SOFTRESET		2
+#define STIH416_USB0_SOFTRESET		3
+#define STIH416_USB1_SOFTRESET		4
+#define STIH416_USB2_SOFTRESET		5
+#define STIH416_USB3_SOFTRESET		6
+#define STIH416_SATA0_SOFTRESET		7
+#define STIH416_SATA1_SOFTRESET		8
+#define STIH416_PCIE0_SOFTRESET		9
+#define STIH416_PCIE1_SOFTRESET		10
+#define STIH416_AUD_DAC_SOFTRESET	11
+#define STIH416_HDTVOUT_SOFTRESET	12
+#define STIH416_VTAC_M_RX_SOFTRESET	13
+#define STIH416_VTAC_A_RX_SOFTRESET	14
+#define STIH416_SYNC_HD_SOFTRESET	15
+#define STIH416_SYNC_SD_SOFTRESET	16
+#define STIH416_BLITTER_SOFTRESET	17
+#define STIH416_GPU_SOFTRESET		18
+#define STIH416_VTAC_M_TX_SOFTRESET	19
+#define STIH416_VTAC_A_TX_SOFTRESET	20
+#define STIH416_VTG_AUX_SOFTRESET	21
+#define STIH416_JPEG_DEC_SOFTRESET	22
+#define STIH416_HVA_SOFTRESET		23
+#define STIH416_COMPO_M_SOFTRESET	24
+#define STIH416_COMPO_A_SOFTRESET	25
+#define STIH416_VP8_DEC_SOFTRESET	26
+#define STIH416_VTG_MAIN_SOFTRESET	27
+
+#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH416 */