Blackfin: DNP5370: new board port

Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This commit is contained in:
Andreas Schallenberg 2010-11-24 22:15:16 +00:00 committed by Mike Frysinger
parent d57bc0feaa
commit 3ea9f2bf5a
4 changed files with 546 additions and 0 deletions

View File

@ -0,0 +1,121 @@
CONFIG_EXPERIMENTAL=y
CONFIG_LOCALVERSION="DNP5370"
CONFIG_SYSVIPC=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
CONFIG_EMBEDDED=y
CONFIG_SLOB=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_IOSCHED_CFQ is not set
CONFIG_BF537=y
CONFIG_BF_REV_0_3=y
CONFIG_DNP5370=y
CONFIG_IRQ_ERROR=7
# CONFIG_CYCLES_CLOCKSOURCE is not set
CONFIG_C_CDPRIO=y
CONFIG_C_AMBEN_B0_B1_B2=y
CONFIG_PM=y
# CONFIG_SUSPEND is not set
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_RARP=y
CONFIG_SYN_COOKIES=y
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
# CONFIG_INET_LRO is not set
# CONFIG_INET_DIAG is not set
# CONFIG_IPV6 is not set
CONFIG_LLC2=y
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_MTD=y
CONFIG_MTD_DEBUG=y
CONFIG_MTD_DEBUG_VERBOSE=1
CONFIG_MTD_PARTITIONS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_NFTL=y
CONFIG_NFTL_RW=y
CONFIG_MTD_CFI=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_MTD_ROM=y
CONFIG_MTD_ABSENT=y
CONFIG_MTD_COMPLEX_MAPPINGS=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_UCLINUX=y
CONFIG_MTD_PLATRAM=y
CONFIG_MTD_DATAFLASH=y
CONFIG_MTD_BLOCK2MTD=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_PLATFORM=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
# CONFIG_MISC_DEVICES is not set
CONFIG_NETDEVICES=y
CONFIG_DAVICOM_PHY=y
CONFIG_NET_ETHERNET=y
CONFIG_BFIN_MAC=y
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_WLAN is not set
# CONFIG_INPUT is not set
# CONFIG_SERIO is not set
# CONFIG_BFIN_DMA_INTERFACE is not set
# CONFIG_VT is not set
# CONFIG_DEVKMEM is not set
CONFIG_BFIN_JTAG_COMM=y
CONFIG_BFIN_JTAG_COMM_CONSOLE=y
CONFIG_SERIAL_BFIN=y
CONFIG_SERIAL_BFIN_CONSOLE=y
CONFIG_SERIAL_BFIN_UART0=y
CONFIG_LEGACY_PTY_COUNT=64
# CONFIG_HW_RANDOM is not set
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_BLACKFIN_TWI=y
CONFIG_SPI=y
CONFIG_SPI_BFIN=y
CONFIG_SPI_SPIDEV=y
CONFIG_GPIOLIB=y
CONFIG_GPIO_SYSFS=y
CONFIG_SENSORS_LM75=y
# CONFIG_USB_SUPPORT is not set
CONFIG_MMC=y
CONFIG_MMC_SPI=y
CONFIG_DMADEVICES=y
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
# CONFIG_DNOTIFY is not set
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=850
CONFIG_JFFS2_FS=y
CONFIG_CRAMFS=y
CONFIG_ROMFS_FS=y
CONFIG_ROMFS_BACKED_BY_BOTH=y
# CONFIG_NETWORK_FILESYSTEMS is not set
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_CODEPAGE_850=y
CONFIG_NLS_ISO8859_1=y
CONFIG_DEBUG_KERNEL=y
CONFIG_DEBUG_SHIRQ=y
CONFIG_DETECT_HUNG_TASK=y
CONFIG_DEBUG_OBJECTS=y
CONFIG_DEBUG_LOCK_ALLOC=y
CONFIG_DEBUG_KOBJECT=y
CONFIG_DEBUG_INFO=y
CONFIG_DEBUG_VM=y
CONFIG_DEBUG_MEMORY_INIT=y
CONFIG_DEBUG_LIST=y
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_PAGE_POISONING=y
# CONFIG_FTRACE is not set
CONFIG_DEBUG_DOUBLEFAULT=y
CONFIG_CPLB_INFO=y
CONFIG_CRC_CCITT=y

View File

@ -39,4 +39,10 @@ config CAMSIG_MINOTAUR
help
Board supply package for CSP Minotaur
config DNP5370
bool "SSV Dil/NetPC DNP/5370"
depends on (BF537)
help
Board supply package for DNP/5370 DIL64 module
endchoice

View File

@ -8,3 +8,4 @@ obj-$(CONFIG_BFIN537_BLUETECHNIX_CM_U) += cm_bf537u.o
obj-$(CONFIG_BFIN537_BLUETECHNIX_TCM) += tcm_bf537.o
obj-$(CONFIG_PNAV10) += pnav10.o
obj-$(CONFIG_CAMSIG_MINOTAUR) += minotaur.o
obj-$(CONFIG_DNP5370) += dnp5370.o

View File

@ -0,0 +1,418 @@
/*
* This is the configuration for SSV Dil/NetPC DNP/5370 board.
*
* DIL module: http://www.dilnetpc.com/dnp0086.htm
* SK28 (starter kit): http://www.dilnetpc.com/dnp0088.htm
*
* Copyright 2010 3ality Digital Systems
* Copyright 2005 National ICT Australia (NICTA)
* Copyright 2004-2006 Analog Devices Inc.
*
* Licensed under the GPL-2 or later.
*/
#include <linux/device.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/plat-ram.h>
#include <linux/mtd/physmap.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/irq.h>
#include <linux/interrupt.h>
#include <linux/i2c.h>
#include <linux/spi/mmc_spi.h>
#include <linux/phy.h>
#include <asm/dma.h>
#include <asm/bfin5xx_spi.h>
#include <asm/reboot.h>
#include <asm/portmux.h>
#include <asm/dpmc.h>
/*
* Name the Board for the /proc/cpuinfo
*/
const char bfin_board_name[] = "DNP/5370";
#define FLASH_MAC 0x202f0000
#define CONFIG_MTD_PHYSMAP_LEN 0x300000
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
.id = -1,
};
#endif
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
#include <linux/bfin_mac.h>
static const unsigned short bfin_mac_peripherals[] = P_RMII0;
static struct bfin_phydev_platform_data bfin_phydev_data[] = {
{
.addr = 1,
.irq = PHY_POLL, /* IRQ_MAC_PHYINT */
},
};
static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
.phydev_number = 1,
.phydev_data = bfin_phydev_data,
.phy_mode = PHY_INTERFACE_MODE_RMII,
.mac_peripherals = bfin_mac_peripherals,
};
static struct platform_device bfin_mii_bus = {
.name = "bfin_mii_bus",
.dev = {
.platform_data = &bfin_mii_bus_data,
}
};
static struct platform_device bfin_mac_device = {
.name = "bfin_mac",
.dev = {
.platform_data = &bfin_mii_bus,
}
};
#endif
#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
static struct mtd_partition asmb_flash_partitions[] = {
{
.name = "bootloader(nor)",
.size = 0x30000,
.offset = 0,
}, {
.name = "linux kernel and rootfs(nor)",
.size = 0x300000 - 0x30000 - 0x10000,
.offset = MTDPART_OFS_APPEND,
}, {
.name = "MAC address(nor)",
.size = 0x10000,
.offset = MTDPART_OFS_APPEND,
.mask_flags = MTD_WRITEABLE,
}
};
static struct physmap_flash_data asmb_flash_data = {
.width = 1,
.parts = asmb_flash_partitions,
.nr_parts = ARRAY_SIZE(asmb_flash_partitions),
};
static struct resource asmb_flash_resource = {
.start = 0x20000000,
.end = 0x202fffff,
.flags = IORESOURCE_MEM,
};
/* 4 MB NOR flash attached to async memory banks 0-2,
* therefore only 3 MB visible.
*/
static struct platform_device asmb_flash_device = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &asmb_flash_data,
},
.num_resources = 1,
.resource = &asmb_flash_resource,
};
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
#define MMC_SPI_CARD_DETECT_INT IRQ_PF5
static int bfin_mmc_spi_init(struct device *dev,
irqreturn_t (*detect_int)(int, void *), void *data)
{
return request_irq(MMC_SPI_CARD_DETECT_INT, detect_int,
IRQF_TRIGGER_FALLING, "mmc-spi-detect", data);
}
static void bfin_mmc_spi_exit(struct device *dev, void *data)
{
free_irq(MMC_SPI_CARD_DETECT_INT, data);
}
static struct bfin5xx_spi_chip mmc_spi_chip_info = {
.enable_dma = 0, /* use no dma transfer with this chip*/
.bits_per_word = 8,
};
static struct mmc_spi_platform_data bfin_mmc_spi_pdata = {
.init = bfin_mmc_spi_init,
.exit = bfin_mmc_spi_exit,
.detect_delay = 100, /* msecs */
};
#endif
#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
/* This mapping is for at45db642 it has 1056 page size,
* partition size and offset should be page aligned
*/
static struct mtd_partition bfin_spi_dataflash_partitions[] = {
{
.name = "JFFS2 dataflash(nor)",
#ifdef CONFIG_MTD_PAGESIZE_1024
.offset = 0x40000,
.size = 0x7C0000,
#else
.offset = 0x0,
.size = 0x840000,
#endif
}
};
static struct flash_platform_data bfin_spi_dataflash_data = {
.name = "mtd_dataflash",
.parts = bfin_spi_dataflash_partitions,
.nr_parts = ARRAY_SIZE(bfin_spi_dataflash_partitions),
.type = "mtd_dataflash",
};
static struct bfin5xx_spi_chip spi_dataflash_chip_info = {
.enable_dma = 0, /* use no dma transfer with this chip*/
.bits_per_word = 8,
};
#endif
static struct spi_board_info bfin_spi_board_info[] __initdata = {
/* SD/MMC card reader at SPI bus */
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{
.modalias = "mmc_spi",
.max_speed_hz = 20000000,
.bus_num = 0,
.chip_select = 1,
.platform_data = &bfin_mmc_spi_pdata,
.controller_data = &mmc_spi_chip_info,
.mode = SPI_MODE_3,
},
#endif
/* 8 Megabyte Atmel NOR flash chip at SPI bus */
#if defined(CONFIG_MTD_DATAFLASH) || defined(CONFIG_MTD_DATAFLASH_MODULE)
{
.modalias = "mtd_dataflash",
.max_speed_hz = 16700000,
.bus_num = 0,
.chip_select = 2,
.platform_data = &bfin_spi_dataflash_data,
.controller_data = &spi_dataflash_chip_info,
.mode = SPI_MODE_3, /* SPI_CPHA and SPI_CPOL */
},
#endif
};
/* SPI controller data */
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[0] = {
.start = SPI0_REGBASE,
.end = SPI0_REGBASE + 0xFF,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = CH_SPI,
.end = CH_SPI,
.flags = IORESOURCE_DMA,
},
[2] = {
.start = IRQ_SPI,
.end = IRQ_SPI,
.flags = IORESOURCE_IRQ,
},
};
static struct bfin5xx_spi_master spi_bfin_master_info = {
.num_chipselect = 8,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
static struct platform_device spi_bfin_master_device = {
.name = "bfin-spi",
.id = 0, /* Bus number */
.num_resources = ARRAY_SIZE(bfin_spi0_resource),
.resource = bfin_spi0_resource,
.dev = {
.platform_data = &spi_bfin_master_info, /* Passed to driver */
},
};
#endif
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
#ifdef CONFIG_SERIAL_BFIN_UART0
static struct resource bfin_uart0_resources[] = {
{
.start = UART0_THR,
.end = UART0_GCTL+2,
.flags = IORESOURCE_MEM,
},
{
.start = IRQ_UART0_RX,
.end = IRQ_UART0_RX+1,
.flags = IORESOURCE_IRQ,
},
{
.start = IRQ_UART0_ERROR,
.end = IRQ_UART0_ERROR,
.flags = IORESOURCE_IRQ,
},
{
.start = CH_UART0_TX,
.end = CH_UART0_TX,
.flags = IORESOURCE_DMA,
},
{
.start = CH_UART0_RX,
.end = CH_UART0_RX,
.flags = IORESOURCE_DMA,
},
};
static unsigned short bfin_uart0_peripherals[] = {
P_UART0_TX, P_UART0_RX, 0
};
static struct platform_device bfin_uart0_device = {
.name = "bfin-uart",
.id = 0,
.num_resources = ARRAY_SIZE(bfin_uart0_resources),
.resource = bfin_uart0_resources,
.dev = {
.platform_data = &bfin_uart0_peripherals, /* Passed to driver */
},
};
#endif
#ifdef CONFIG_SERIAL_BFIN_UART1
static struct resource bfin_uart1_resources[] = {
{
.start = UART1_THR,
.end = UART1_GCTL+2,
.flags = IORESOURCE_MEM,
},
{
.start = IRQ_UART1_RX,
.end = IRQ_UART1_RX+1,
.flags = IORESOURCE_IRQ,
},
{
.start = IRQ_UART1_ERROR,
.end = IRQ_UART1_ERROR,
.flags = IORESOURCE_IRQ,
},
{
.start = CH_UART1_TX,
.end = CH_UART1_TX,
.flags = IORESOURCE_DMA,
},
{
.start = CH_UART1_RX,
.end = CH_UART1_RX,
.flags = IORESOURCE_DMA,
},
};
static unsigned short bfin_uart1_peripherals[] = {
P_UART1_TX, P_UART1_RX, 0
};
static struct platform_device bfin_uart1_device = {
.name = "bfin-uart",
.id = 1,
.num_resources = ARRAY_SIZE(bfin_uart1_resources),
.resource = bfin_uart1_resources,
.dev = {
.platform_data = &bfin_uart1_peripherals, /* Passed to driver */
},
};
#endif
#endif
#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
static struct resource bfin_twi0_resource[] = {
[0] = {
.start = TWI0_REGBASE,
.end = TWI0_REGBASE + 0xff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_TWI,
.end = IRQ_TWI,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device i2c_bfin_twi_device = {
.name = "i2c-bfin-twi",
.id = 0,
.num_resources = ARRAY_SIZE(bfin_twi0_resource),
.resource = bfin_twi0_resource,
};
#endif
static struct platform_device *dnp5370_devices[] __initdata = {
#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
#ifdef CONFIG_SERIAL_BFIN_UART0
&bfin_uart0_device,
#endif
#ifdef CONFIG_SERIAL_BFIN_UART1
&bfin_uart1_device,
#endif
#endif
#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
&asmb_flash_device,
#endif
#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
&bfin_mii_bus,
&bfin_mac_device,
#endif
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
&spi_bfin_master_device,
#endif
#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
&i2c_bfin_twi_device,
#endif
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
&rtc_device,
#endif
};
static int __init dnp5370_init(void)
{
printk(KERN_INFO "DNP/5370: registering device resources\n");
platform_add_devices(dnp5370_devices, ARRAY_SIZE(dnp5370_devices));
printk(KERN_INFO "DNP/5370: registering %zu SPI slave devices\n",
ARRAY_SIZE(bfin_spi_board_info));
spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
printk(KERN_INFO "DNP/5370: MAC %pM\n", (void *)FLASH_MAC);
return 0;
}
arch_initcall(dnp5370_init);
/*
* Currently the MAC address is saved in Flash by U-Boot
*/
void bfin_get_ether_addr(char *addr)
{
*(u32 *)(&(addr[0])) = bfin_read32(FLASH_MAC);
*(u16 *)(&(addr[4])) = bfin_read16(FLASH_MAC + 4);
}
EXPORT_SYMBOL(bfin_get_ether_addr);