sh: SH-2007 board support.

This patch series adds support for ITO Co., Ltd.'s SH-2007 reference
platform (A PC-104 based SH7780 platform).

This is a direct port of the out-of-tree board support from the vendor's
kernel, originally located at:

	http://ms-n.org/sh-linux/kernel/

More information on the board and the vendor can be obtained from the
vendor's site at:

	http://www.itonet.co.jp/

Presently supported peripherals are CF and ethernet, with support for
the on-board IDE still pending further testing.

Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

arch/sh/boards/Kconfig

@@ -309,6 +309,17 @@ config SH_POLARIS
 	help
 	  Select if configuring for an SMSC Polaris development board
 
+config SH_SH2007
+	bool "SH-2007 board"
+	select NO_IOPORT
+	depends on CPU_SUBTYPE_SH7780
+	help
+	  SH-2007 is a single-board computer based around SH7780 chip
+	  intended for embedded applications.
+	  It has an Ethernet interface (SMC9118), direct connected
+	  Compact Flash socket, two serial ports and PC-104 bus.
+	  More information at <http://sh2000.sh-linux.org>.
+
 endmenu
 
 source "arch/sh/boards/mach-r2d/Kconfig"

arch/sh/boards/Makefile

@@ -2,6 +2,7 @@
 # Specific board support, not covered by a mach group.
 #
 obj-$(CONFIG_SH_MAGIC_PANEL_R2)	+= board-magicpanelr2.o
+obj-$(CONFIG_SH_SH2007)		+= board-sh2007.o
 obj-$(CONFIG_SH_SH7785LCR)	+= board-sh7785lcr.o
 obj-$(CONFIG_SH_URQUELL)	+= board-urquell.o
 obj-$(CONFIG_SH_SHMIN)		+= board-shmin.o

arch/sh/boards/board-sh2007.c

@@ -0,0 +1,133 @@
+/*
+ * SH-2007 board support.
+ *
+ * Copyright (C) 2003, 2004  SUGIOKA Toshinobu
+ * Copyright (C) 2010  Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
+ */
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/smsc911x.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+#include <linux/io.h>
+#include <asm/machvec.h>
+#include <mach/sh2007.h>
+
+struct smsc911x_platform_config smc911x_info = {
+	.flags		= SMSC911X_USE_32BIT,
+	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type	= SMSC911X_IRQ_TYPE_PUSH_PULL,
+};
+
+static struct resource smsc9118_0_resources[] = {
+	[0] = {
+		.start	= SMC0_BASE,
+		.end	= SMC0_BASE + 0xff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= evt2irq(0x240),
+		.end	= evt2irq(0x240),
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static struct resource smsc9118_1_resources[] = {
+	[0] = {
+		.start	= SMC1_BASE,
+		.end	= SMC1_BASE + 0xff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= evt2irq(0x280),
+		.end	= evt2irq(0x280),
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device smsc9118_0_device = {
+	.name		= "smsc911x",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(smsc9118_0_resources),
+	.resource	= smsc9118_0_resources,
+	.dev = {
+		.platform_data = &smc911x_info,
+	},
+};
+
+static struct platform_device smsc9118_1_device = {
+	.name		= "smsc911x",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(smsc9118_1_resources),
+	.resource	= smsc9118_1_resources,
+	.dev = {
+		.platform_data = &smc911x_info,
+	},
+};
+
+static struct resource cf_resources[] = {
+	[0] = {
+		.start	= CF_BASE + CF_OFFSET,
+		.end	= CF_BASE + CF_OFFSET + 0x0f,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= CF_BASE + CF_OFFSET + 0x206,
+		.end	= CF_BASE + CF_OFFSET + 0x20f,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+		.start	= evt2irq(0x2c0),
+		.end	= evt2irq(0x2c0),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device cf_device  = {
+	.name		= "pata_platform",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(cf_resources),
+	.resource	= cf_resources,
+};
+
+static struct platform_device *sh2007_devices[] __initdata = {
+	&smsc9118_0_device,
+	&smsc9118_1_device,
+	&cf_device,
+};
+
+static int __init sh2007_io_init(void)
+{
+	platform_add_devices(sh2007_devices, ARRAY_SIZE(sh2007_devices));
+	return 0;
+}
+subsys_initcall(sh2007_io_init);
+
+static void __init sh2007_init_irq(void)
+{
+	plat_irq_setup_pins(IRQ_MODE_IRQ);
+}
+
+/*
+ * Initialize the board
+ */
+static void __init sh2007_setup(char **cmdline_p)
+{
+	printk(KERN_INFO "SH-2007 Setup...");
+
+	/* setup wait control registers for area 5 */
+	__raw_writel(CS5BCR_D, CS5BCR);
+	__raw_writel(CS5WCR_D, CS5WCR);
+	__raw_writel(CS5PCR_D, CS5PCR);
+
+	printk(KERN_INFO " done.\n");
+}
+
+/*
+ * The Machine Vector
+ */
+struct sh_machine_vector mv_sh2007 __initmv = {
+	.mv_setup		= sh2007_setup,
+	.mv_name		= "sh2007",
+	.mv_init_irq		= sh2007_init_irq,
+};

arch/sh/include/mach-common/mach/sh2007.h

@@ -0,0 +1,117 @@
+#ifndef __MACH_SH2007_H
+#define __MACH_SH2007_H
+
+#define CS5BCR		0xff802050
+#define CS5WCR		0xff802058
+#define CS5PCR		0xff802070
+
+#define BUS_SZ8		1
+#define BUS_SZ16	2
+#define BUS_SZ32	3
+
+#define PCMCIA_IODYN	1
+#define PCMCIA_ATA	0
+#define PCMCIA_IO8	2
+#define PCMCIA_IO16	3
+#define PCMCIA_COMM8	4
+#define PCMCIA_COMM16	5
+#define PCMCIA_ATTR8	6
+#define PCMCIA_ATTR16	7
+
+#define TYPE_SRAM	0
+#define TYPE_PCMCIA	4
+
+/* write-read/write-write delay (0-7:0,1,2,3,4,5,6,7) */
+#define IWW5		0
+#define IWW6		3
+/* different area, read-write delay (0-7:0,1,2,3,4,5,6,7) */
+#define IWRWD5		2
+#define IWRWD6		2
+/* same area, read-write delay (0-7:0,1,2,3,4,5,6,7) */
+#define IWRWS5		2
+#define IWRWS6		2
+/* different area, read-read delay (0-7:0,1,2,3,4,5,6,7) */
+#define IWRRD5		2
+#define IWRRD6		2
+/* same area, read-read delay (0-7:0,1,2,3,4,5,6,7) */
+#define IWRRS5		0
+#define IWRRS6		2
+/* burst count (0-3:4,8,16,32) */
+#define BST5		0
+#define BST6		0
+/* bus size */
+#define SZ5		BUS_SZ16
+#define SZ6		BUS_SZ16
+/* RD hold for SRAM (0-1:0,1) */
+#define RDSPL5		0
+#define RDSPL6		0
+/* Burst pitch (0-7:0,1,2,3,4,5,6,7) */
+#define BW5		0
+#define BW6		0
+/* Multiplex (0-1:0,1) */
+#define MPX5		0
+#define MPX6		0
+/* device type */
+#define TYPE5		TYPE_PCMCIA
+#define TYPE6		TYPE_PCMCIA
+/* address setup before assert CSn for SRAM (0-7:0,1,2,3,4,5,6,7) */
+#define ADS5		0
+#define ADS6		0
+/* address hold after negate CSn for SRAM (0-7:0,1,2,3,4,5,6,7) */
+#define ADH5		0
+#define ADH6		0
+/* CSn assert to RD assert delay for SRAM (0-7:0,1,2,3,4,5,6,7) */
+#define RDS5		0
+#define RDS6		0
+/* RD negate to CSn negate delay for SRAM (0-7:0,1,2,3,4,5,6,7) */
+#define RDH5		0
+#define RDH6		0
+/* CSn assert to WE assert delay for SRAM (0-7:0,1,2,3,4,5,6,7) */
+#define WTS5		0
+#define WTS6		0
+/* WE negate to CSn negate delay for SRAM (0-7:0,1,2,3,4,5,6,7) */
+#define WTH5		0
+#define WTH6		0
+/* BS hold (0-1:1,2) */
+#define BSH5		0
+#define BSH6		0
+/* wait cycle (0-15:0,1,2,3,4,5,6,7,8,9,11,13,15,17,21,25) */
+#define IW5		6	/* 60ns PIO mode 4 */
+#define IW6		15	/* 250ns */
+
+#define SAA5		PCMCIA_IODYN	/* IDE area b4000000-b5ffffff */
+#define SAB5		PCMCIA_IODYN	/* CF  area b6000000-b7ffffff */
+#define PCWA5		0	/* additional wait A (0-3:0,15,30,50) */
+#define PCWB5		0	/* additional wait B (0-3:0,15,30,50) */
+/* wait B (0-15:0,1,2,3,4,5,6,7,8,9,11,13,15,17,21,25) */
+#define PCIW5		12
+/* Address->OE/WE assert delay A (0-7:0,1,2,3,6,9,12,15) */
+#define TEDA5		2
+/* Address->OE/WE assert delay B (0-7:0,1,2,3,6,9,12,15) */
+#define TEDB5		4
+/* OE/WE negate->Address delay A (0-7:0,1,2,3,6,9,12,15) */
+#define TEHA5		2
+/* OE/WE negate->Address delay B (0-7:0,1,2,3,6,9,12,15) */
+#define TEHB5		3
+
+#define CS5BCR_D	((IWW5<<28)|(IWRWD5<<24)|(IWRWS5<<20)|		\
+			(IWRRD5<<16)|(IWRRS5<<12)|(BST5<<10)|		\
+			(SZ5<<8)|(RDSPL5<<7)|(BW5<<4)|(MPX5<<3)|TYPE5)
+#define CS5WCR_D	((ADS5<<28)|(ADH5<<24)|(RDS5<<20)|	\
+			(RDH5<<16)|(WTS5<<12)|(WTH5<<8)|(BSH5<<4)|IW5)
+#define CS5PCR_D	((SAA5<<28)|(SAB5<<24)|(PCWA5<<22)|		\
+			(PCWB5<<20)|(PCIW5<<16)|(TEDA5<<12)|		\
+			(TEDB5<<8)|(TEHA5<<4)|TEHB5)
+
+#define SMC0_BASE       0xb0800000      /* eth0 */
+#define SMC1_BASE       0xb0900000      /* eth1 */
+#define CF_BASE         0xb6100000      /* Compact Flash (I/O area) */
+#define IDE_BASE        0xb4000000      /* IDE */
+#define PC104_IO_BASE   0xb8000000
+#define PC104_MEM_BASE  0xba000000
+#define SMC_IO_SIZE     0x100
+
+#define CF_OFFSET       0x1f0
+#define IDE_OFFSET      0x170
+
+#endif /* __MACH_SH2007_H */

arch/sh/tools/mach-types

@@ -52,6 +52,7 @@ MIGOR			SH_MIGOR
 RSK7201			SH_RSK7201
 RSK7203			SH_RSK7203
 AP325RXA		SH_AP325RXA
+SH2007			SH_SH2007
 SH7763RDP		SH_SH7763RDP
 SH7785LCR		SH_SH7785LCR
 SH7785LCR_PT		SH_SH7785LCR_PT

drivers/serial/sh-sci.h

@@ -140,7 +140,15 @@
 # define SCSPTR0	0xffe00024	/* 16 bit SCIF */
 # define SCSPTR1	0xffe10024	/* 16 bit SCIF */
 # define SCIF_ORER	0x0001		/* Overrun error bit */
-# define SCSCR_INIT(port)	0x3a	/* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
+
+#if defined(CONFIG_SH_SH2007)
+/* TIE=0,RIE=0,TE=1,RE=1,REIE=1,CKE1=0 */
+# define SCSCR_INIT(port)	0x38
+#else
+/* TIE=0,RIE=0,TE=1,RE=1,REIE=1,CKE1=1 */
+# define SCSCR_INIT(port)	0x3a
+#endif
+
 #elif defined(CONFIG_CPU_SUBTYPE_SH7785) || \
       defined(CONFIG_CPU_SUBTYPE_SH7786)
 # define SCSPTR0	0xffea0024	/* 16 bit SCIF */
@@ -599,9 +607,10 @@ static inline int sci_rxd_in(struct uart_port *port)
  * -- Mitch Davis - 15 Jul 2000
  */
 
-#if defined(CONFIG_CPU_SUBTYPE_SH7780) || \
+#if (defined(CONFIG_CPU_SUBTYPE_SH7780)  || \
      defined(CONFIG_CPU_SUBTYPE_SH7785)  || \
-    defined(CONFIG_CPU_SUBTYPE_SH7786)
+     defined(CONFIG_CPU_SUBTYPE_SH7786)) && \
+    !defined(CONFIG_SH_SH2007)
 #define SCBRR_VALUE(bps, clk) ((clk+16*bps)/(16*bps)-1)
 #elif defined(CONFIG_CPU_SUBTYPE_SH7705) || \
       defined(CONFIG_CPU_SUBTYPE_SH7720) || \