forked from Minki/linux
ARM: mvebu: dts: Add dts file for DLink DNS-327L
DNS-327L is a 2-bay NAS with the following specs:
- 512MiB RAM
- 128MiB NAND Flash
- 1 GbE interface (Marvell PHY)
- 1 rear USB 3.0 port (via PCIe USB 3.0 controller)
- 2 internal SATA ports handled by the Armada 370:
uses 2 gpios for power control
- two front 2-color leds (amber + white) for both discs,
controlled by the SoC
- One white LED handled by SoC (USB)
- 3 buttons. Power handled by weltrend, USB and
RESET (on the bottom) are wired via GPIOs
- Unidentified i2c device at address 0x13 (via i2cdetect)
- UART0 providing serial console
- Weltrend MCU serving for RTC, temperature, fan control,
and power button handling interfaced via UART1
(Handled via userspace dns320l-daemon)
Signed-off-by: Andrew Andrianov <andrew@ncrmnt.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit is contained in:
Andrew Andrianov
Gregory CLEMENT
parent
e9f3ed4ac4
commit
16b79921e3
@ -624,6 +624,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
|
||||
zynq-zybo.dtb
|
||||
dtb-$(CONFIG_MACH_ARMADA_370) += \
|
||||
armada-370-db.dtb \
|
||||
armada-370-dlink-dns327l.dtb \
|
||||
armada-370-mirabox.dtb \
|
||||
armada-370-netgear-rn102.dtb \
|
||||
armada-370-netgear-rn104.dtb \
|
||||
|
||||
357
arch/arm/boot/dts/armada-370-dlink-dns327l.dts
Normal file
357
arch/arm/boot/dts/armada-370-dlink-dns327l.dts
Normal file
@ -0,0 +1,357 @@
|
||||
/*
|
||||
* Device Tree file for D-Link DNS-327L
|
||||
*
|
||||
* Copyright (C) 2015, Andrew Andrianov <andrew@ncrmnt.org>
|
||||
*
|
||||
* This file is dual-licensed: you can use it either under the terms
|
||||
* of the GPL or the X11 license, at your option. Note that this dual
|
||||
* licensing only applies to this file, and not this project as a
|
||||
* whole.
|
||||
*
|
||||
* a) This file is free software; you can redistribute it and/or
|
||||
* modify it under the terms of the GNU General Public License as
|
||||
* published by the Free Software Foundation; either version 2 of the
|
||||
* License, or (at your option) any later version.
|
||||
*
|
||||
* This file is distributed in the hope that it will be useful
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* Or, alternatively
|
||||
*
|
||||
* b) Permission is hereby granted, free of charge, to any person
|
||||
* obtaining a copy of this software and associated documentation
|
||||
* files (the "Software"), to deal in the Software without
|
||||
* restriction, including without limitation the rights to use
|
||||
* copy, modify, merge, publish, distribute, sublicense, and/or
|
||||
* sell copies of the Software, and to permit persons to whom the
|
||||
* Software is furnished to do so, subject to the following
|
||||
* conditions:
|
||||
*
|
||||
* The above copyright notice and this permission notice shall be
|
||||
* included in all copies or substantial portions of the Software.
|
||||
*
|
||||
* THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
|
||||
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
|
||||
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
|
||||
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
|
||||
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
|
||||
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
|
||||
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
|
||||
* OTHER DEALINGS IN THE SOFTWARE.
|
||||
*/
|
||||
|
||||
/* Remaining unsolved:
|
||||
* There's still some unknown device on i2c address 0x13
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include "armada-370.dtsi"
|
||||
|
||||
/ {
|
||||
model = "D-Link DNS-327L";
|
||||
compatible = "dlink,dns327l",
|
||||
"marvell,armada370",
|
||||
"marvell,armada-370-xp";
|
||||
|
||||
chosen {
|
||||
stdout-path = &uart0;
|
||||
};
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x00000000 0x20000000>; /* 512 MiB */
|
||||
};
|
||||
|
||||
soc {
|
||||
ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
|
||||
MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
|
||||
|
||||
pcie-controller {
|
||||
status = "okay";
|
||||
|
||||
pcie@1,0 {
|
||||
/* Port 0, Lane 0 */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
pcie@2,0 {
|
||||
/* Port 1, Lane 0 */
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
internal-regs {
|
||||
sata@a0000 {
|
||||
nr-ports = <2>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb@50000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
nand@d0000 {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
marvell,nand-keep-config;
|
||||
marvell,nand-enable-arbiter;
|
||||
nand-on-flash-bbt;
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
/* 1.0 MiB */
|
||||
reg = <0x0000000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
/* 128 KiB */
|
||||
reg = <0x100000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@120000 {
|
||||
label = "uImage";
|
||||
/* 7 MiB */
|
||||
reg = <0x120000 0x700000>;
|
||||
};
|
||||
|
||||
partition@820000 {
|
||||
label = "ubifs";
|
||||
/* ~ 84 MiB */
|
||||
reg = <0x820000 0x54e0000>;
|
||||
};
|
||||
|
||||
/* Hardcoded into stock bootloader */
|
||||
partition@5d00000 {
|
||||
label = "failsafe-uImage";
|
||||
/* 5 MiB */
|
||||
reg = <0x5d00000 0x500000>;
|
||||
};
|
||||
|
||||
partition@6200000 {
|
||||
label = "failsafe-fs";
|
||||
/* 29 MiB */
|
||||
reg = <0x6200000 0x1d00000>;
|
||||
};
|
||||
|
||||
partition@7f00000 {
|
||||
label = "bbt";
|
||||
/* 1 MiB for BBT */
|
||||
reg = <0x7f00000 0x100000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <
|
||||
&backup_button_pin
|
||||
&power_button_pin
|
||||
&reset_button_pin>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
power-button {
|
||||
label = "Power Button";
|
||||
linux,code = <KEY_POWER>;
|
||||
gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
backup-button {
|
||||
label = "Backup Button";
|
||||
linux,code = <KEY_COPY>;
|
||||
gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
reset-button {
|
||||
label = "Reset Button";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <
|
||||
&sata_l_amber_pin
|
||||
&sata_r_amber_pin
|
||||
&backup_led_pin
|
||||
/* Ensure these are managed by hardware */
|
||||
&sata_l_white_pin
|
||||
&sata_r_white_pin>;
|
||||
|
||||
pinctrl-names = "default";
|
||||
|
||||
sata-r-amber-pin {
|
||||
label = "dns327l:amber:sata-r";
|
||||
gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "keep";
|
||||
};
|
||||
|
||||
sata-l-amber-pin {
|
||||
label = "dns327l:amber:sata-l";
|
||||
gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "keep";
|
||||
};
|
||||
|
||||
backup-led-pin {
|
||||
label = "dns327l:white:usb";
|
||||
gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "keep";
|
||||
};
|
||||
};
|
||||
|
||||
regulators {
|
||||
compatible = "simple-bus";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
usb_power: regulator@1 {
|
||||
compatible = "regulator-fixed";
|
||||
reg = <1>;
|
||||
pinctrl-0 = <&xhci_pwr_pin>;
|
||||
pinctrl-names = "default";
|
||||
regulator-name = "USB3.0 Port Power";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
enable-active-high;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
sata_r_power: regulator@2 {
|
||||
compatible = "regulator-fixed";
|
||||
reg = <2>;
|
||||
pinctrl-0 = <&sata_r_pwr_pin>;
|
||||
pinctrl-names = "default";
|
||||
regulator-name = "SATA-R Power";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
startup-delay-us = <2000000>;
|
||||
enable-active-high;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
sata_l_power: regulator@3 {
|
||||
compatible = "regulator-fixed";
|
||||
reg = <3>;
|
||||
pinctrl-0 = <&sata_l_pwr_pin>;
|
||||
pinctrl-names = "default";
|
||||
regulator-name = "SATA-L Power";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
startup-delay-us = <4000000>;
|
||||
enable-active-high;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
gpio = <&gpio1 24 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
sata_l_white_pin: sata-l-white-pin {
|
||||
marvell,pins = "mpp57";
|
||||
marvell,function = "sata0";
|
||||
};
|
||||
|
||||
sata_r_white_pin: sata-r-white-pin {
|
||||
marvell,pins = "mpp55";
|
||||
marvell,function = "sata1";
|
||||
};
|
||||
|
||||
sata_r_amber_pin: sata-r-amber-pin {
|
||||
marvell,pins = "mpp52";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
sata_l_amber_pin: sata-l-amber-pin {
|
||||
marvell,pins = "mpp53";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
backup_led_pin: backup-led-pin {
|
||||
marvell,pins = "mpp61";
|
||||
marvell,function = "gpo";
|
||||
};
|
||||
|
||||
xhci_pwr_pin: xhci-pwr-pin {
|
||||
marvell,pins = "mpp13";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
sata_r_pwr_pin: sata-r-pwr-pin {
|
||||
marvell,pins = "mpp54";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
sata_l_pwr_pin: sata-l-pwr-pin {
|
||||
marvell,pins = "mpp56";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
uart1_pins: uart1-pins {
|
||||
marvell,pins = "mpp60", "mpp61";
|
||||
marvell,function = "uart1";
|
||||
};
|
||||
|
||||
power_button_pin: power-button-pin {
|
||||
marvell,pins = "mpp65";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
backup_button_pin: backup-button-pin {
|
||||
marvell,pins = "mpp63";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
|
||||
reset_button_pin: reset-button-pin {
|
||||
marvell,pins = "mpp64";
|
||||
marvell,function = "gpio";
|
||||
};
|
||||
};
|
||||
|
||||
/* Serial console */
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/* Connected to Weltrend MCU */
|
||||
&uart1 {
|
||||
pinctrl-0 = <&uart1_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
phy0: ethernet-phy@0 { /* Marvell 88E1318 */
|
||||
reg = <0>;
|
||||
marvell,reg-init = <0x0 0x16 0x0 0x0002>,
|
||||
<0x0 0x19 0x0 0x0077>,
|
||||
<0x0 0x18 0x0 0x5747>;
|
||||
};
|
||||
};
|
||||
|
||||
ð1 {
|
||||
phy = <&phy0>;
|
||||
phy-mode = "rgmii-id";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c0 {
|
||||
compatible = "marvell,mv64xxx-i2c";
|
||||
clock-frequency = <100000>;
|
||||
status = "okay";
|
||||
};
|
||||
Loading…
Reference in New Issue
Block a user