linux/drivers/clk/meson/meson8b.c

1194 lines
32 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (c) 2015 Endless Mobile, Inc.
* Author: Carlo Caione <carlo@endlessm.com>
*
* Copyright (c) 2016 BayLibre, Inc.
* Michael Turquette <mturquette@baylibre.com>
*/
#include <linux/clk.h>
#include <linux/clk-provider.h>
#include <linux/init.h>
#include <linux/mfd/syscon.h>
#include <linux/of_address.h>
#include <linux/reset-controller.h>
#include <linux/slab.h>
#include <linux/regmap.h>
#include "clkc.h"
#include "meson8b.h"
#include "clk-regmap.h"
static DEFINE_SPINLOCK(meson_clk_lock);
struct meson8b_clk_reset {
struct reset_controller_dev reset;
struct regmap *regmap;
};
static const struct pll_params_table sys_pll_params_table[] = {
PLL_PARAMS(50, 1),
PLL_PARAMS(51, 1),
PLL_PARAMS(52, 1),
PLL_PARAMS(53, 1),
PLL_PARAMS(54, 1),
PLL_PARAMS(55, 1),
PLL_PARAMS(56, 1),
PLL_PARAMS(57, 1),
PLL_PARAMS(58, 1),
PLL_PARAMS(59, 1),
PLL_PARAMS(60, 1),
PLL_PARAMS(61, 1),
PLL_PARAMS(62, 1),
PLL_PARAMS(63, 1),
PLL_PARAMS(64, 1),
clk: meson: meson8b: add support for more M/N values in sys_pll The sys_pll on the EC-100 board is configured to 1584MHz at boot (either by u-boot, firmware or chip defaults). This is achieved by using M = 66, N = 1 (24MHz * 66 / 1). At boot the CPU clock is running off sys_pll divided by 2 which results in 792MHz. Thus M = 66 is considered to be a "safe" value for Meson8b. To achieve 1608MHz (one of the CPU OPPs on Meson8 and Meson8m2) we need M = 67, N = 1. I ran "stress --cpu 4" while infinitely cycling through all available frequencies on my Meson8m2 board and could not spot any issues with this setting (after ~12 hours of running this). On Meson8, Meson8b and Meson8m2 we also want to be able to use 408MHz and 816MHz CPU frequencies. These can be achieved by dividing sys_pll by 4 (for 408MHz) or 2 (for 816MHz). That means that sys_pll has to run at 1632MHz which can be generated using M = 68, N = 1. Similarily we also want to be able to use 1008MHz as CPU frequency. This means that sys_pll has to run either at 1008MHz or 2016MHz. The former would result in an M value of 42, which is lower than the smallest value used by the 3.10 GPL kernel sources from Amlogic (50 is the lower limit there). Thus we need to run sys_pll at 2016MHz which can ge generated using M = 84, N = 1. I tested M = 68 and M = 84 on my Meson8b Odroid-C1 and my Meson8m2 board by running "stress --cpu 4" while infinitely cycling thorugh all available frequencies. I could not spot any issues after ~12 hours of running this. Amlogic's 3.10 GPL kernel sources have more M/N combinations. I did not add them yet because M = 74 (to achieve close to 1800MHz on Meson8) and M = 82 (to achieve close to 1992MHz on Meson8 as well) caused my Meson8m2 board to hang randomly. It's not clear why this is (for example because the board's voltage regulator design is bad, some missing bits for these values in our clk-pll driver, etc.). Thus the following M values from the Amlogic 3.10 GPL kernel sources are skipped as of now: 69, 70, 71, 72, 73, 74, 76, 78, 80, 82, 84, 86, 88, 90, 92, 94, 96, 98 Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lkml.kernel.org/r/20181115224048.13511-5-martin.blumenstingl@googlemail.com
2018-11-15 22:40:46 +00:00
PLL_PARAMS(65, 1),
PLL_PARAMS(66, 1),
PLL_PARAMS(67, 1),
PLL_PARAMS(68, 1),
PLL_PARAMS(84, 1),
{ /* sentinel */ },
};
static struct clk_fixed_rate meson8b_xtal = {
.fixed_rate = 24000000,
.hw.init = &(struct clk_init_data){
.name = "xtal",
.num_parents = 0,
.ops = &clk_fixed_rate_ops,
},
};
static struct clk_regmap meson8b_fixed_pll_dco = {
.data = &(struct meson_clk_pll_data){
.en = {
.reg_off = HHI_MPLL_CNTL,
.shift = 30,
.width = 1,
},
.m = {
.reg_off = HHI_MPLL_CNTL,
.shift = 0,
.width = 9,
},
.n = {
.reg_off = HHI_MPLL_CNTL,
.shift = 9,
.width = 5,
},
.frac = {
.reg_off = HHI_MPLL_CNTL2,
.shift = 0,
.width = 12,
},
.l = {
.reg_off = HHI_MPLL_CNTL,
.shift = 31,
.width = 1,
},
.rst = {
.reg_off = HHI_MPLL_CNTL,
.shift = 29,
.width = 1,
},
},
.hw.init = &(struct clk_init_data){
.name = "fixed_pll_dco",
.ops = &meson_clk_pll_ro_ops,
.parent_names = (const char *[]){ "xtal" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_fixed_pll = {
.data = &(struct clk_regmap_div_data){
.offset = HHI_MPLL_CNTL,
.shift = 16,
.width = 2,
.flags = CLK_DIVIDER_POWER_OF_TWO,
},
.hw.init = &(struct clk_init_data){
.name = "fixed_pll",
.ops = &clk_regmap_divider_ro_ops,
.parent_names = (const char *[]){ "fixed_pll_dco" },
.num_parents = 1,
/*
* This clock won't ever change at runtime so
* CLK_SET_RATE_PARENT is not required
*/
},
};
static struct clk_regmap meson8b_vid_pll_dco = {
.data = &(struct meson_clk_pll_data){
.en = {
.reg_off = HHI_VID_PLL_CNTL,
.shift = 30,
.width = 1,
},
.m = {
.reg_off = HHI_VID_PLL_CNTL,
.shift = 0,
.width = 9,
},
.n = {
.reg_off = HHI_VID_PLL_CNTL,
.shift = 9,
.width = 5,
},
.l = {
.reg_off = HHI_VID_PLL_CNTL,
.shift = 31,
.width = 1,
},
.rst = {
.reg_off = HHI_VID_PLL_CNTL,
.shift = 29,
.width = 1,
},
},
.hw.init = &(struct clk_init_data){
.name = "vid_pll_dco",
.ops = &meson_clk_pll_ro_ops,
.parent_names = (const char *[]){ "xtal" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_vid_pll = {
.data = &(struct clk_regmap_div_data){
.offset = HHI_VID_PLL_CNTL,
.shift = 16,
.width = 2,
.flags = CLK_DIVIDER_POWER_OF_TWO,
},
.hw.init = &(struct clk_init_data){
.name = "vid_pll",
.ops = &clk_regmap_divider_ro_ops,
.parent_names = (const char *[]){ "vid_pll_dco" },
.num_parents = 1,
.flags = CLK_SET_RATE_PARENT,
},
};
static struct clk_regmap meson8b_sys_pll_dco = {
.data = &(struct meson_clk_pll_data){
.en = {
.reg_off = HHI_SYS_PLL_CNTL,
.shift = 30,
.width = 1,
},
.m = {
.reg_off = HHI_SYS_PLL_CNTL,
.shift = 0,
.width = 9,
},
.n = {
.reg_off = HHI_SYS_PLL_CNTL,
.shift = 9,
.width = 5,
},
.l = {
.reg_off = HHI_SYS_PLL_CNTL,
.shift = 31,
.width = 1,
},
.rst = {
.reg_off = HHI_SYS_PLL_CNTL,
.shift = 29,
.width = 1,
},
.table = sys_pll_params_table,
},
.hw.init = &(struct clk_init_data){
.name = "sys_pll_dco",
.ops = &meson_clk_pll_ro_ops,
.parent_names = (const char *[]){ "xtal" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_sys_pll = {
.data = &(struct clk_regmap_div_data){
.offset = HHI_SYS_PLL_CNTL,
.shift = 16,
.width = 2,
.flags = CLK_DIVIDER_POWER_OF_TWO,
},
.hw.init = &(struct clk_init_data){
.name = "sys_pll",
.ops = &clk_regmap_divider_ro_ops,
.parent_names = (const char *[]){ "sys_pll_dco" },
.num_parents = 1,
.flags = CLK_SET_RATE_PARENT,
},
};
static struct clk_fixed_factor meson8b_fclk_div2_div = {
.mult = 1,
.div = 2,
.hw.init = &(struct clk_init_data){
.name = "fclk_div2_div",
.ops = &clk_fixed_factor_ops,
.parent_names = (const char *[]){ "fixed_pll" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_fclk_div2 = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_MPLL_CNTL6,
.bit_idx = 27,
},
.hw.init = &(struct clk_init_data){
.name = "fclk_div2",
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "fclk_div2_div" },
.num_parents = 1,
/*
* FIXME: Ethernet with a RGMII PHYs is not working if
* fclk_div2 is disabled. it is currently unclear why this
* is. keep it enabled until the Ethernet driver knows how
* to manage this clock.
*/
.flags = CLK_IS_CRITICAL,
},
};
static struct clk_fixed_factor meson8b_fclk_div3_div = {
.mult = 1,
.div = 3,
.hw.init = &(struct clk_init_data){
.name = "fclk_div3_div",
.ops = &clk_fixed_factor_ops,
.parent_names = (const char *[]){ "fixed_pll" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_fclk_div3 = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_MPLL_CNTL6,
.bit_idx = 28,
},
.hw.init = &(struct clk_init_data){
.name = "fclk_div3",
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "fclk_div3_div" },
.num_parents = 1,
},
};
static struct clk_fixed_factor meson8b_fclk_div4_div = {
.mult = 1,
.div = 4,
.hw.init = &(struct clk_init_data){
.name = "fclk_div4_div",
.ops = &clk_fixed_factor_ops,
.parent_names = (const char *[]){ "fixed_pll" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_fclk_div4 = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_MPLL_CNTL6,
.bit_idx = 29,
},
.hw.init = &(struct clk_init_data){
.name = "fclk_div4",
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "fclk_div4_div" },
.num_parents = 1,
},
};
static struct clk_fixed_factor meson8b_fclk_div5_div = {
.mult = 1,
.div = 5,
.hw.init = &(struct clk_init_data){
.name = "fclk_div5_div",
.ops = &clk_fixed_factor_ops,
.parent_names = (const char *[]){ "fixed_pll" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_fclk_div5 = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_MPLL_CNTL6,
.bit_idx = 30,
},
.hw.init = &(struct clk_init_data){
.name = "fclk_div5",
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "fclk_div5_div" },
.num_parents = 1,
},
};
static struct clk_fixed_factor meson8b_fclk_div7_div = {
.mult = 1,
.div = 7,
.hw.init = &(struct clk_init_data){
.name = "fclk_div7_div",
.ops = &clk_fixed_factor_ops,
.parent_names = (const char *[]){ "fixed_pll" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_fclk_div7 = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_MPLL_CNTL6,
.bit_idx = 31,
},
.hw.init = &(struct clk_init_data){
.name = "fclk_div7",
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "fclk_div7_div" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_mpll_prediv = {
.data = &(struct clk_regmap_div_data){
.offset = HHI_MPLL_CNTL5,
.shift = 12,
.width = 1,
},
.hw.init = &(struct clk_init_data){
.name = "mpll_prediv",
.ops = &clk_regmap_divider_ro_ops,
.parent_names = (const char *[]){ "fixed_pll" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_mpll0_div = {
.data = &(struct meson_clk_mpll_data){
.sdm = {
.reg_off = HHI_MPLL_CNTL7,
.shift = 0,
.width = 14,
},
.sdm_en = {
.reg_off = HHI_MPLL_CNTL7,
.shift = 15,
.width = 1,
},
.n2 = {
.reg_off = HHI_MPLL_CNTL7,
.shift = 16,
.width = 9,
},
.ssen = {
.reg_off = HHI_MPLL_CNTL,
.shift = 25,
.width = 1,
},
.lock = &meson_clk_lock,
},
.hw.init = &(struct clk_init_data){
.name = "mpll0_div",
.ops = &meson_clk_mpll_ops,
.parent_names = (const char *[]){ "mpll_prediv" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_mpll0 = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_MPLL_CNTL7,
.bit_idx = 14,
},
.hw.init = &(struct clk_init_data){
.name = "mpll0",
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "mpll0_div" },
.num_parents = 1,
.flags = CLK_SET_RATE_PARENT,
},
};
static struct clk_regmap meson8b_mpll1_div = {
.data = &(struct meson_clk_mpll_data){
.sdm = {
.reg_off = HHI_MPLL_CNTL8,
.shift = 0,
.width = 14,
},
.sdm_en = {
.reg_off = HHI_MPLL_CNTL8,
.shift = 15,
.width = 1,
},
.n2 = {
.reg_off = HHI_MPLL_CNTL8,
.shift = 16,
.width = 9,
},
.lock = &meson_clk_lock,
},
.hw.init = &(struct clk_init_data){
.name = "mpll1_div",
.ops = &meson_clk_mpll_ops,
.parent_names = (const char *[]){ "mpll_prediv" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_mpll1 = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_MPLL_CNTL8,
.bit_idx = 14,
},
.hw.init = &(struct clk_init_data){
.name = "mpll1",
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "mpll1_div" },
.num_parents = 1,
.flags = CLK_SET_RATE_PARENT,
},
};
static struct clk_regmap meson8b_mpll2_div = {
.data = &(struct meson_clk_mpll_data){
.sdm = {
.reg_off = HHI_MPLL_CNTL9,
.shift = 0,
.width = 14,
},
.sdm_en = {
.reg_off = HHI_MPLL_CNTL9,
.shift = 15,
.width = 1,
},
.n2 = {
.reg_off = HHI_MPLL_CNTL9,
.shift = 16,
.width = 9,
},
.lock = &meson_clk_lock,
},
.hw.init = &(struct clk_init_data){
.name = "mpll2_div",
.ops = &meson_clk_mpll_ops,
.parent_names = (const char *[]){ "mpll_prediv" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_mpll2 = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_MPLL_CNTL9,
.bit_idx = 14,
},
.hw.init = &(struct clk_init_data){
.name = "mpll2",
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "mpll2_div" },
.num_parents = 1,
.flags = CLK_SET_RATE_PARENT,
},
};
static u32 mux_table_clk81[] = { 6, 5, 7 };
static struct clk_regmap meson8b_mpeg_clk_sel = {
.data = &(struct clk_regmap_mux_data){
.offset = HHI_MPEG_CLK_CNTL,
.mask = 0x7,
.shift = 12,
.table = mux_table_clk81,
},
.hw.init = &(struct clk_init_data){
.name = "mpeg_clk_sel",
.ops = &clk_regmap_mux_ro_ops,
/*
* FIXME bits 14:12 selects from 8 possible parents:
* xtal, 1'b0 (wtf), fclk_div7, mpll_clkout1, mpll_clkout2,
* fclk_div4, fclk_div3, fclk_div5
*/
.parent_names = (const char *[]){ "fclk_div3", "fclk_div4",
"fclk_div5" },
.num_parents = 3,
},
};
static struct clk_regmap meson8b_mpeg_clk_div = {
.data = &(struct clk_regmap_div_data){
.offset = HHI_MPEG_CLK_CNTL,
.shift = 0,
.width = 7,
},
.hw.init = &(struct clk_init_data){
.name = "mpeg_clk_div",
.ops = &clk_regmap_divider_ro_ops,
.parent_names = (const char *[]){ "mpeg_clk_sel" },
.num_parents = 1,
},
};
static struct clk_regmap meson8b_clk81 = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_MPEG_CLK_CNTL,
.bit_idx = 7,
},
.hw.init = &(struct clk_init_data){
.name = "clk81",
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "mpeg_clk_div" },
.num_parents = 1,
.flags = CLK_IS_CRITICAL,
},
};
static struct clk_regmap meson8b_cpu_in_sel = {
.data = &(struct clk_regmap_mux_data){
.offset = HHI_SYS_CPU_CLK_CNTL0,
.mask = 0x1,
.shift = 0,
},
.hw.init = &(struct clk_init_data){
.name = "cpu_in_sel",
.ops = &clk_regmap_mux_ro_ops,
.parent_names = (const char *[]){ "xtal", "sys_pll" },
.num_parents = 2,
.flags = (CLK_SET_RATE_PARENT |
CLK_SET_RATE_NO_REPARENT),
},
};
static struct clk_fixed_factor meson8b_cpu_div2 = {
.mult = 1,
.div = 2,
.hw.init = &(struct clk_init_data){
.name = "cpu_div2",
.ops = &clk_fixed_factor_ops,
.parent_names = (const char *[]){ "cpu_in_sel" },
.num_parents = 1,
.flags = CLK_SET_RATE_PARENT,
},
};
static struct clk_fixed_factor meson8b_cpu_div3 = {
.mult = 1,
.div = 3,
.hw.init = &(struct clk_init_data){
.name = "cpu_div3",
.ops = &clk_fixed_factor_ops,
.parent_names = (const char *[]){ "cpu_in_sel" },
.num_parents = 1,
.flags = CLK_SET_RATE_PARENT,
},
};
static const struct clk_div_table cpu_scale_table[] = {
clk: meson: meson8b: fix incorrect divider mapping in cpu_scale_table The public S805 datasheet only mentions that HHI_SYS_CPU_CLK_CNTL1[20:29] contains a divider called "cpu_scale_div". Unfortunately it does not mention how to use the register contents. The Amlogic 3.10 GPL kernel sources are using the following code to calculate the CPU clock based on that register (taken from arch/arm/mach-meson8/clock.c in the 3.10 Amlogic kernel, shortened to make it easier to read): N = (aml_read_reg32(P_HHI_SYS_CPU_CLK_CNTL1) >> 20) & 0x3FF; if (sel == 3) /* use cpu_scale_div */ div = 2 * N; else div = ... /* not relevant for this example */ cpu_clk = parent_clk / div; This suggests that the formula is: parent_rate / 2 * register_value However, running perf (which can measure the CPU clock rate thanks to the ARM PMU) shows that this formula is not correct. This can be reproduced with the following steps: 1. boot into u-boot 2. let the CPU clock run off the XTAL clock: mw.l 0xC110419C 0x30 1 3. set the cpu_scale_div register: to value 0x1: mw.l 0xC110415C 0x801016A2 1 to value 0x2: mw.l 0xC110415C 0x802016A2 1 to value 0x5: mw.l 0xC110415C 0x805016A2 1 4. let the CPU clock run off cpu_scale_div: mw.l 0xC110419C 0xbd 1 5. boot Linux 6. run: perf stat -aB stress --cpu 4 --timeout 10 7. check the "cycles" value I get the following results depending on the cpu_scale_div value: - (cpu_in_sel - this is the input clock for cpu_scale_div - runs at 1.2GHz) - 0x1 = 300MHz - 0x2 = 200MHz - 0x5 = 100MHz This means that the actual formula to calculate the output of the cpu_scale_div clock is: parent_rate / 2 * (register value + 1). The register value 0x0 is reserved. When letting the CPU clock run off the cpu_scale_div while the value is 0x0 the whole board hangs (even in u-boot). I also verified this with the TWD timer: when adding this to the .dts without specifying it's clock it will auto-detect the PERIPH (which is the input clock of the TWD) clock rate (and the result is shown in the kernel log). On Meson8, Meson8b and Meson8m2 the PERIPH clock is CPUCLK divided by 4. This also matched for all three test-cases from above (in all cases the TWD timer clock rate was approx. one fourth of the CPU clock rate). A small note regarding the "fixes" tag: the original issue seems to exist virtually since forever. Even commit 28b9fcd016126e ("clk: meson8b: Add support for Meson8b clocks") seems to handle this wrong. I still decided to use commit 251b6fd38bcb9c ("clk: meson: rework meson8b cpu clock") because this is the first commit which gets the CPU hiearchy correct and thus it's the first commit where the cpu_scale_div register is used correctly (apart from the bug in the cpu_scale_table). Fixes: 251b6fd38bcb9c ("clk: meson: rework meson8b cpu clock") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lkml.kernel.org/r/20180927085921.24627-2-martin.blumenstingl@googlemail.com
2018-09-27 08:59:20 +00:00
{ .val = 1, .div = 4 },
{ .val = 2, .div = 6 },
{ .val = 3, .div = 8 },
{ .val = 4, .div = 10 },
{ .val = 5, .div = 12 },
{ .val = 6, .div = 14 },
{ .val = 7, .div = 16 },
{ .val = 8, .div = 18 },
{ /* sentinel */ },
};
static struct clk_regmap meson8b_cpu_scale_div = {
.data = &(struct clk_regmap_div_data){
.offset = HHI_SYS_CPU_CLK_CNTL1,
.shift = 20,
.width = 10,
.table = cpu_scale_table,
.flags = CLK_DIVIDER_ALLOW_ZERO,
},
.hw.init = &(struct clk_init_data){
.name = "cpu_scale_div",
.ops = &clk_regmap_divider_ro_ops,
.parent_names = (const char *[]){ "cpu_in_sel" },
.num_parents = 1,
.flags = CLK_SET_RATE_PARENT,
},
};
static u32 mux_table_cpu_scale_out_sel[] = { 0, 1, 3 };
static struct clk_regmap meson8b_cpu_scale_out_sel = {
.data = &(struct clk_regmap_mux_data){
.offset = HHI_SYS_CPU_CLK_CNTL0,
.mask = 0x3,
.shift = 2,
.table = mux_table_cpu_scale_out_sel,
},
.hw.init = &(struct clk_init_data){
.name = "cpu_scale_out_sel",
.ops = &clk_regmap_mux_ro_ops,
/*
* NOTE: We are skipping the parent with value 0x2 (which is
* "cpu_div3") because it results in a duty cycle of 33% which
* makes the system unstable and can result in a lockup of the
* whole system.
*/
.parent_names = (const char *[]) { "cpu_in_sel",
"cpu_div2",
"cpu_scale_div" },
.num_parents = 3,
.flags = CLK_SET_RATE_PARENT,
},
};
static struct clk_regmap meson8b_cpu_clk = {
.data = &(struct clk_regmap_mux_data){
.offset = HHI_SYS_CPU_CLK_CNTL0,
.mask = 0x1,
.shift = 7,
},
.hw.init = &(struct clk_init_data){
.name = "cpu_clk",
.ops = &clk_regmap_mux_ro_ops,
.parent_names = (const char *[]){ "xtal",
"cpu_scale_out_sel" },
.num_parents = 2,
.flags = (CLK_SET_RATE_PARENT |
CLK_SET_RATE_NO_REPARENT |
CLK_IS_CRITICAL),
},
};
clk: meson: meson8b: add support for the NAND clocks This adds the NAND clocks (from the HHI_NAND_CLK_CNTL register) to the Meson8b clock driver. There are three NAND clocks: a gate which enables or disables the NAND clock, a mux and a divider (which divides the mux output). Unfortunately the public S805 datasheet does not document the mux parents. However, the vendor kernel has a few hints for us which allows us to make an educated guess about the clock parents. To do this we need to have a look at set_nand_core_clk() from the vendor's NAND driver (see [0]): - XTAL = (4<<9) | (1<<8) | 0 - 160MHz = (0<<9) | (1<<8) | 3) - 182MHz = (3<<9) | (1<<8) | 1) - 212MHz = (1<<9) | (1<<8) | 3) - 255MHz = (2<<9) | (1<<8) | 1) While there is a comment for the XTAL parent (which indicates that it should only be used for debugging) we have to do a bit of math for the other parents: target_freq * divider = rate of parent clock Bit 8 above is the enable bit, so we can ignore it here. Bits 11:9 are the mux index and bits 6:0 are the 0-based divider (so we need to add 1). This gives us: - mux 0 (160MHz * 4) = fclk_div4 (actual rate = 637.5MHz, off by 2.5MHz) - mux 1 (212MHz * 4) = fclk_div3 (actual rate = 850MHz, off by 2MHz) - mux 2 (255MHz * 2) = fclk_div5 (matches exactly 510MHz) - mux 3 (182MHz * 2) = fclk_div7 (actual rate = 346.3MHz, off by 0.3MHz) [0] https://github.com/khadas/linux/blob/9587681285cb/drivers/amlogic/amlnf/dev/amlnf_ctrl.c#L314 Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
2018-04-23 19:35:09 +00:00
static struct clk_regmap meson8b_nand_clk_sel = {
.data = &(struct clk_regmap_mux_data){
.offset = HHI_NAND_CLK_CNTL,
.mask = 0x7,
.shift = 9,
.flags = CLK_MUX_ROUND_CLOSEST,
},
.hw.init = &(struct clk_init_data){
.name = "nand_clk_sel",
.ops = &clk_regmap_mux_ops,
/* FIXME all other parents are unknown: */
.parent_names = (const char *[]){ "fclk_div4", "fclk_div3",
"fclk_div5", "fclk_div7", "xtal" },
.num_parents = 5,
.flags = CLK_SET_RATE_PARENT,
},
};
static struct clk_regmap meson8b_nand_clk_div = {
.data = &(struct clk_regmap_div_data){
.offset = HHI_NAND_CLK_CNTL,
.shift = 0,
.width = 7,
.flags = CLK_DIVIDER_ROUND_CLOSEST,
},
.hw.init = &(struct clk_init_data){
.name = "nand_clk_div",
.ops = &clk_regmap_divider_ops,
.parent_names = (const char *[]){ "nand_clk_sel" },
.num_parents = 1,
.flags = CLK_SET_RATE_PARENT,
},
};
static struct clk_regmap meson8b_nand_clk_gate = {
.data = &(struct clk_regmap_gate_data){
.offset = HHI_NAND_CLK_CNTL,
.bit_idx = 8,
},
.hw.init = &(struct clk_init_data){
.name = "nand_clk_gate",
.ops = &clk_regmap_gate_ops,
.parent_names = (const char *[]){ "nand_clk_div" },
.num_parents = 1,
.flags = CLK_SET_RATE_PARENT,
},
};
/* Everything Else (EE) domain gates */
static MESON_GATE(meson8b_ddr, HHI_GCLK_MPEG0, 0);
static MESON_GATE(meson8b_dos, HHI_GCLK_MPEG0, 1);
static MESON_GATE(meson8b_isa, HHI_GCLK_MPEG0, 5);
static MESON_GATE(meson8b_pl301, HHI_GCLK_MPEG0, 6);
static MESON_GATE(meson8b_periphs, HHI_GCLK_MPEG0, 7);
static MESON_GATE(meson8b_spicc, HHI_GCLK_MPEG0, 8);
static MESON_GATE(meson8b_i2c, HHI_GCLK_MPEG0, 9);
static MESON_GATE(meson8b_sar_adc, HHI_GCLK_MPEG0, 10);
static MESON_GATE(meson8b_smart_card, HHI_GCLK_MPEG0, 11);
static MESON_GATE(meson8b_rng0, HHI_GCLK_MPEG0, 12);
static MESON_GATE(meson8b_uart0, HHI_GCLK_MPEG0, 13);
static MESON_GATE(meson8b_sdhc, HHI_GCLK_MPEG0, 14);
static MESON_GATE(meson8b_stream, HHI_GCLK_MPEG0, 15);
static MESON_GATE(meson8b_async_fifo, HHI_GCLK_MPEG0, 16);
static MESON_GATE(meson8b_sdio, HHI_GCLK_MPEG0, 17);
static MESON_GATE(meson8b_abuf, HHI_GCLK_MPEG0, 18);
static MESON_GATE(meson8b_hiu_iface, HHI_GCLK_MPEG0, 19);
static MESON_GATE(meson8b_assist_misc, HHI_GCLK_MPEG0, 23);
static MESON_GATE(meson8b_spi, HHI_GCLK_MPEG0, 30);
static MESON_GATE(meson8b_i2s_spdif, HHI_GCLK_MPEG1, 2);
static MESON_GATE(meson8b_eth, HHI_GCLK_MPEG1, 3);
static MESON_GATE(meson8b_demux, HHI_GCLK_MPEG1, 4);
static MESON_GATE(meson8b_aiu_glue, HHI_GCLK_MPEG1, 6);
static MESON_GATE(meson8b_iec958, HHI_GCLK_MPEG1, 7);
static MESON_GATE(meson8b_i2s_out, HHI_GCLK_MPEG1, 8);
static MESON_GATE(meson8b_amclk, HHI_GCLK_MPEG1, 9);
static MESON_GATE(meson8b_aififo2, HHI_GCLK_MPEG1, 10);
static MESON_GATE(meson8b_mixer, HHI_GCLK_MPEG1, 11);
static MESON_GATE(meson8b_mixer_iface, HHI_GCLK_MPEG1, 12);
static MESON_GATE(meson8b_adc, HHI_GCLK_MPEG1, 13);
static MESON_GATE(meson8b_blkmv, HHI_GCLK_MPEG1, 14);
static MESON_GATE(meson8b_aiu, HHI_GCLK_MPEG1, 15);
static MESON_GATE(meson8b_uart1, HHI_GCLK_MPEG1, 16);
static MESON_GATE(meson8b_g2d, HHI_GCLK_MPEG1, 20);
static MESON_GATE(meson8b_usb0, HHI_GCLK_MPEG1, 21);
static MESON_GATE(meson8b_usb1, HHI_GCLK_MPEG1, 22);
static MESON_GATE(meson8b_reset, HHI_GCLK_MPEG1, 23);
static MESON_GATE(meson8b_nand, HHI_GCLK_MPEG1, 24);
static MESON_GATE(meson8b_dos_parser, HHI_GCLK_MPEG1, 25);
static MESON_GATE(meson8b_usb, HHI_GCLK_MPEG1, 26);
static MESON_GATE(meson8b_vdin1, HHI_GCLK_MPEG1, 28);
static MESON_GATE(meson8b_ahb_arb0, HHI_GCLK_MPEG1, 29);
static MESON_GATE(meson8b_efuse, HHI_GCLK_MPEG1, 30);
static MESON_GATE(meson8b_boot_rom, HHI_GCLK_MPEG1, 31);
static MESON_GATE(meson8b_ahb_data_bus, HHI_GCLK_MPEG2, 1);
static MESON_GATE(meson8b_ahb_ctrl_bus, HHI_GCLK_MPEG2, 2);
static MESON_GATE(meson8b_hdmi_intr_sync, HHI_GCLK_MPEG2, 3);
static MESON_GATE(meson8b_hdmi_pclk, HHI_GCLK_MPEG2, 4);
static MESON_GATE(meson8b_usb1_ddr_bridge, HHI_GCLK_MPEG2, 8);
static MESON_GATE(meson8b_usb0_ddr_bridge, HHI_GCLK_MPEG2, 9);
static MESON_GATE(meson8b_mmc_pclk, HHI_GCLK_MPEG2, 11);
static MESON_GATE(meson8b_dvin, HHI_GCLK_MPEG2, 12);
static MESON_GATE(meson8b_uart2, HHI_GCLK_MPEG2, 15);
static MESON_GATE(meson8b_sana, HHI_GCLK_MPEG2, 22);
static MESON_GATE(meson8b_vpu_intr, HHI_GCLK_MPEG2, 25);
static MESON_GATE(meson8b_sec_ahb_ahb3_bridge, HHI_GCLK_MPEG2, 26);
static MESON_GATE(meson8b_clk81_a9, HHI_GCLK_MPEG2, 29);
static MESON_GATE(meson8b_vclk2_venci0, HHI_GCLK_OTHER, 1);
static MESON_GATE(meson8b_vclk2_venci1, HHI_GCLK_OTHER, 2);
static MESON_GATE(meson8b_vclk2_vencp0, HHI_GCLK_OTHER, 3);
static MESON_GATE(meson8b_vclk2_vencp1, HHI_GCLK_OTHER, 4);
static MESON_GATE(meson8b_gclk_venci_int, HHI_GCLK_OTHER, 8);
static MESON_GATE(meson8b_gclk_vencp_int, HHI_GCLK_OTHER, 9);
static MESON_GATE(meson8b_dac_clk, HHI_GCLK_OTHER, 10);
static MESON_GATE(meson8b_aoclk_gate, HHI_GCLK_OTHER, 14);
static MESON_GATE(meson8b_iec958_gate, HHI_GCLK_OTHER, 16);
static MESON_GATE(meson8b_enc480p, HHI_GCLK_OTHER, 20);
static MESON_GATE(meson8b_rng1, HHI_GCLK_OTHER, 21);
static MESON_GATE(meson8b_gclk_vencl_int, HHI_GCLK_OTHER, 22);
static MESON_GATE(meson8b_vclk2_venclmcc, HHI_GCLK_OTHER, 24);
static MESON_GATE(meson8b_vclk2_vencl, HHI_GCLK_OTHER, 25);
static MESON_GATE(meson8b_vclk2_other, HHI_GCLK_OTHER, 26);
static MESON_GATE(meson8b_edp, HHI_GCLK_OTHER, 31);
/* Always On (AO) domain gates */
static MESON_GATE(meson8b_ao_media_cpu, HHI_GCLK_AO, 0);
static MESON_GATE(meson8b_ao_ahb_sram, HHI_GCLK_AO, 1);
static MESON_GATE(meson8b_ao_ahb_bus, HHI_GCLK_AO, 2);
static MESON_GATE(meson8b_ao_iface, HHI_GCLK_AO, 3);
static struct clk_hw_onecell_data meson8b_hw_onecell_data = {
.hws = {
[CLKID_XTAL] = &meson8b_xtal.hw,
[CLKID_PLL_FIXED] = &meson8b_fixed_pll.hw,
[CLKID_PLL_VID] = &meson8b_vid_pll.hw,
[CLKID_PLL_SYS] = &meson8b_sys_pll.hw,
[CLKID_FCLK_DIV2] = &meson8b_fclk_div2.hw,
[CLKID_FCLK_DIV3] = &meson8b_fclk_div3.hw,
[CLKID_FCLK_DIV4] = &meson8b_fclk_div4.hw,
[CLKID_FCLK_DIV5] = &meson8b_fclk_div5.hw,
[CLKID_FCLK_DIV7] = &meson8b_fclk_div7.hw,
[CLKID_CPUCLK] = &meson8b_cpu_clk.hw,
[CLKID_MPEG_SEL] = &meson8b_mpeg_clk_sel.hw,
[CLKID_MPEG_DIV] = &meson8b_mpeg_clk_div.hw,
[CLKID_CLK81] = &meson8b_clk81.hw,
[CLKID_DDR] = &meson8b_ddr.hw,
[CLKID_DOS] = &meson8b_dos.hw,
[CLKID_ISA] = &meson8b_isa.hw,
[CLKID_PL301] = &meson8b_pl301.hw,
[CLKID_PERIPHS] = &meson8b_periphs.hw,
[CLKID_SPICC] = &meson8b_spicc.hw,
[CLKID_I2C] = &meson8b_i2c.hw,
[CLKID_SAR_ADC] = &meson8b_sar_adc.hw,
[CLKID_SMART_CARD] = &meson8b_smart_card.hw,
[CLKID_RNG0] = &meson8b_rng0.hw,
[CLKID_UART0] = &meson8b_uart0.hw,
[CLKID_SDHC] = &meson8b_sdhc.hw,
[CLKID_STREAM] = &meson8b_stream.hw,
[CLKID_ASYNC_FIFO] = &meson8b_async_fifo.hw,
[CLKID_SDIO] = &meson8b_sdio.hw,
[CLKID_ABUF] = &meson8b_abuf.hw,
[CLKID_HIU_IFACE] = &meson8b_hiu_iface.hw,
[CLKID_ASSIST_MISC] = &meson8b_assist_misc.hw,
[CLKID_SPI] = &meson8b_spi.hw,
[CLKID_I2S_SPDIF] = &meson8b_i2s_spdif.hw,
[CLKID_ETH] = &meson8b_eth.hw,
[CLKID_DEMUX] = &meson8b_demux.hw,
[CLKID_AIU_GLUE] = &meson8b_aiu_glue.hw,
[CLKID_IEC958] = &meson8b_iec958.hw,
[CLKID_I2S_OUT] = &meson8b_i2s_out.hw,
[CLKID_AMCLK] = &meson8b_amclk.hw,
[CLKID_AIFIFO2] = &meson8b_aififo2.hw,
[CLKID_MIXER] = &meson8b_mixer.hw,
[CLKID_MIXER_IFACE] = &meson8b_mixer_iface.hw,
[CLKID_ADC] = &meson8b_adc.hw,
[CLKID_BLKMV] = &meson8b_blkmv.hw,
[CLKID_AIU] = &meson8b_aiu.hw,
[CLKID_UART1] = &meson8b_uart1.hw,
[CLKID_G2D] = &meson8b_g2d.hw,
[CLKID_USB0] = &meson8b_usb0.hw,
[CLKID_USB1] = &meson8b_usb1.hw,
[CLKID_RESET] = &meson8b_reset.hw,
[CLKID_NAND] = &meson8b_nand.hw,
[CLKID_DOS_PARSER] = &meson8b_dos_parser.hw,
[CLKID_USB] = &meson8b_usb.hw,
[CLKID_VDIN1] = &meson8b_vdin1.hw,
[CLKID_AHB_ARB0] = &meson8b_ahb_arb0.hw,
[CLKID_EFUSE] = &meson8b_efuse.hw,
[CLKID_BOOT_ROM] = &meson8b_boot_rom.hw,
[CLKID_AHB_DATA_BUS] = &meson8b_ahb_data_bus.hw,
[CLKID_AHB_CTRL_BUS] = &meson8b_ahb_ctrl_bus.hw,
[CLKID_HDMI_INTR_SYNC] = &meson8b_hdmi_intr_sync.hw,
[CLKID_HDMI_PCLK] = &meson8b_hdmi_pclk.hw,
[CLKID_USB1_DDR_BRIDGE] = &meson8b_usb1_ddr_bridge.hw,
[CLKID_USB0_DDR_BRIDGE] = &meson8b_usb0_ddr_bridge.hw,
[CLKID_MMC_PCLK] = &meson8b_mmc_pclk.hw,
[CLKID_DVIN] = &meson8b_dvin.hw,
[CLKID_UART2] = &meson8b_uart2.hw,
[CLKID_SANA] = &meson8b_sana.hw,
[CLKID_VPU_INTR] = &meson8b_vpu_intr.hw,
[CLKID_SEC_AHB_AHB3_BRIDGE] = &meson8b_sec_ahb_ahb3_bridge.hw,
[CLKID_CLK81_A9] = &meson8b_clk81_a9.hw,
[CLKID_VCLK2_VENCI0] = &meson8b_vclk2_venci0.hw,
[CLKID_VCLK2_VENCI1] = &meson8b_vclk2_venci1.hw,
[CLKID_VCLK2_VENCP0] = &meson8b_vclk2_vencp0.hw,
[CLKID_VCLK2_VENCP1] = &meson8b_vclk2_vencp1.hw,
[CLKID_GCLK_VENCI_INT] = &meson8b_gclk_venci_int.hw,
[CLKID_GCLK_VENCP_INT] = &meson8b_gclk_vencp_int.hw,
[CLKID_DAC_CLK] = &meson8b_dac_clk.hw,
[CLKID_AOCLK_GATE] = &meson8b_aoclk_gate.hw,
[CLKID_IEC958_GATE] = &meson8b_iec958_gate.hw,
[CLKID_ENC480P] = &meson8b_enc480p.hw,
[CLKID_RNG1] = &meson8b_rng1.hw,
[CLKID_GCLK_VENCL_INT] = &meson8b_gclk_vencl_int.hw,
[CLKID_VCLK2_VENCLMCC] = &meson8b_vclk2_venclmcc.hw,
[CLKID_VCLK2_VENCL] = &meson8b_vclk2_vencl.hw,
[CLKID_VCLK2_OTHER] = &meson8b_vclk2_other.hw,
[CLKID_EDP] = &meson8b_edp.hw,
[CLKID_AO_MEDIA_CPU] = &meson8b_ao_media_cpu.hw,
[CLKID_AO_AHB_SRAM] = &meson8b_ao_ahb_sram.hw,
[CLKID_AO_AHB_BUS] = &meson8b_ao_ahb_bus.hw,
[CLKID_AO_IFACE] = &meson8b_ao_iface.hw,
[CLKID_MPLL0] = &meson8b_mpll0.hw,
[CLKID_MPLL1] = &meson8b_mpll1.hw,
[CLKID_MPLL2] = &meson8b_mpll2.hw,
[CLKID_MPLL0_DIV] = &meson8b_mpll0_div.hw,
[CLKID_MPLL1_DIV] = &meson8b_mpll1_div.hw,
[CLKID_MPLL2_DIV] = &meson8b_mpll2_div.hw,
[CLKID_CPU_IN_SEL] = &meson8b_cpu_in_sel.hw,
[CLKID_CPU_DIV2] = &meson8b_cpu_div2.hw,
[CLKID_CPU_DIV3] = &meson8b_cpu_div3.hw,
[CLKID_CPU_SCALE_DIV] = &meson8b_cpu_scale_div.hw,
[CLKID_CPU_SCALE_OUT_SEL] = &meson8b_cpu_scale_out_sel.hw,
[CLKID_MPLL_PREDIV] = &meson8b_mpll_prediv.hw,
[CLKID_FCLK_DIV2_DIV] = &meson8b_fclk_div2_div.hw,
[CLKID_FCLK_DIV3_DIV] = &meson8b_fclk_div3_div.hw,
[CLKID_FCLK_DIV4_DIV] = &meson8b_fclk_div4_div.hw,
[CLKID_FCLK_DIV5_DIV] = &meson8b_fclk_div5_div.hw,
[CLKID_FCLK_DIV7_DIV] = &meson8b_fclk_div7_div.hw,
clk: meson: meson8b: add support for the NAND clocks This adds the NAND clocks (from the HHI_NAND_CLK_CNTL register) to the Meson8b clock driver. There are three NAND clocks: a gate which enables or disables the NAND clock, a mux and a divider (which divides the mux output). Unfortunately the public S805 datasheet does not document the mux parents. However, the vendor kernel has a few hints for us which allows us to make an educated guess about the clock parents. To do this we need to have a look at set_nand_core_clk() from the vendor's NAND driver (see [0]): - XTAL = (4<<9) | (1<<8) | 0 - 160MHz = (0<<9) | (1<<8) | 3) - 182MHz = (3<<9) | (1<<8) | 1) - 212MHz = (1<<9) | (1<<8) | 3) - 255MHz = (2<<9) | (1<<8) | 1) While there is a comment for the XTAL parent (which indicates that it should only be used for debugging) we have to do a bit of math for the other parents: target_freq * divider = rate of parent clock Bit 8 above is the enable bit, so we can ignore it here. Bits 11:9 are the mux index and bits 6:0 are the 0-based divider (so we need to add 1). This gives us: - mux 0 (160MHz * 4) = fclk_div4 (actual rate = 637.5MHz, off by 2.5MHz) - mux 1 (212MHz * 4) = fclk_div3 (actual rate = 850MHz, off by 2MHz) - mux 2 (255MHz * 2) = fclk_div5 (matches exactly 510MHz) - mux 3 (182MHz * 2) = fclk_div7 (actual rate = 346.3MHz, off by 0.3MHz) [0] https://github.com/khadas/linux/blob/9587681285cb/drivers/amlogic/amlnf/dev/amlnf_ctrl.c#L314 Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
2018-04-23 19:35:09 +00:00
[CLKID_NAND_SEL] = &meson8b_nand_clk_sel.hw,
[CLKID_NAND_DIV] = &meson8b_nand_clk_div.hw,
[CLKID_NAND_CLK] = &meson8b_nand_clk_gate.hw,
[CLKID_PLL_FIXED_DCO] = &meson8b_fixed_pll_dco.hw,
[CLKID_PLL_VID_DCO] = &meson8b_vid_pll_dco.hw,
[CLKID_PLL_SYS_DCO] = &meson8b_sys_pll_dco.hw,
[CLK_NR_CLKS] = NULL,
},
.num = CLK_NR_CLKS,
};
static struct clk_regmap *const meson8b_clk_regmaps[] = {
&meson8b_clk81,
&meson8b_ddr,
&meson8b_dos,
&meson8b_isa,
&meson8b_pl301,
&meson8b_periphs,
&meson8b_spicc,
&meson8b_i2c,
&meson8b_sar_adc,
&meson8b_smart_card,
&meson8b_rng0,
&meson8b_uart0,
&meson8b_sdhc,
&meson8b_stream,
&meson8b_async_fifo,
&meson8b_sdio,
&meson8b_abuf,
&meson8b_hiu_iface,
&meson8b_assist_misc,
&meson8b_spi,
&meson8b_i2s_spdif,
&meson8b_eth,
&meson8b_demux,
&meson8b_aiu_glue,
&meson8b_iec958,
&meson8b_i2s_out,
&meson8b_amclk,
&meson8b_aififo2,
&meson8b_mixer,
&meson8b_mixer_iface,
&meson8b_adc,
&meson8b_blkmv,
&meson8b_aiu,
&meson8b_uart1,
&meson8b_g2d,
&meson8b_usb0,
&meson8b_usb1,
&meson8b_reset,
&meson8b_nand,
&meson8b_dos_parser,
&meson8b_usb,
&meson8b_vdin1,
&meson8b_ahb_arb0,
&meson8b_efuse,
&meson8b_boot_rom,
&meson8b_ahb_data_bus,
&meson8b_ahb_ctrl_bus,
&meson8b_hdmi_intr_sync,
&meson8b_hdmi_pclk,
&meson8b_usb1_ddr_bridge,
&meson8b_usb0_ddr_bridge,
&meson8b_mmc_pclk,
&meson8b_dvin,
&meson8b_uart2,
&meson8b_sana,
&meson8b_vpu_intr,
&meson8b_sec_ahb_ahb3_bridge,
&meson8b_clk81_a9,
&meson8b_vclk2_venci0,
&meson8b_vclk2_venci1,
&meson8b_vclk2_vencp0,
&meson8b_vclk2_vencp1,
&meson8b_gclk_venci_int,
&meson8b_gclk_vencp_int,
&meson8b_dac_clk,
&meson8b_aoclk_gate,
&meson8b_iec958_gate,
&meson8b_enc480p,
&meson8b_rng1,
&meson8b_gclk_vencl_int,
&meson8b_vclk2_venclmcc,
&meson8b_vclk2_vencl,
&meson8b_vclk2_other,
&meson8b_edp,
&meson8b_ao_media_cpu,
&meson8b_ao_ahb_sram,
&meson8b_ao_ahb_bus,
&meson8b_ao_iface,
&meson8b_mpeg_clk_div,
&meson8b_mpeg_clk_sel,
&meson8b_mpll0,
&meson8b_mpll1,
&meson8b_mpll2,
&meson8b_mpll0_div,
&meson8b_mpll1_div,
&meson8b_mpll2_div,
&meson8b_fixed_pll,
&meson8b_vid_pll,
&meson8b_sys_pll,
&meson8b_cpu_in_sel,
&meson8b_cpu_scale_div,
&meson8b_cpu_scale_out_sel,
&meson8b_cpu_clk,
&meson8b_mpll_prediv,
&meson8b_fclk_div2,
&meson8b_fclk_div3,
&meson8b_fclk_div4,
&meson8b_fclk_div5,
&meson8b_fclk_div7,
clk: meson: meson8b: add support for the NAND clocks This adds the NAND clocks (from the HHI_NAND_CLK_CNTL register) to the Meson8b clock driver. There are three NAND clocks: a gate which enables or disables the NAND clock, a mux and a divider (which divides the mux output). Unfortunately the public S805 datasheet does not document the mux parents. However, the vendor kernel has a few hints for us which allows us to make an educated guess about the clock parents. To do this we need to have a look at set_nand_core_clk() from the vendor's NAND driver (see [0]): - XTAL = (4<<9) | (1<<8) | 0 - 160MHz = (0<<9) | (1<<8) | 3) - 182MHz = (3<<9) | (1<<8) | 1) - 212MHz = (1<<9) | (1<<8) | 3) - 255MHz = (2<<9) | (1<<8) | 1) While there is a comment for the XTAL parent (which indicates that it should only be used for debugging) we have to do a bit of math for the other parents: target_freq * divider = rate of parent clock Bit 8 above is the enable bit, so we can ignore it here. Bits 11:9 are the mux index and bits 6:0 are the 0-based divider (so we need to add 1). This gives us: - mux 0 (160MHz * 4) = fclk_div4 (actual rate = 637.5MHz, off by 2.5MHz) - mux 1 (212MHz * 4) = fclk_div3 (actual rate = 850MHz, off by 2MHz) - mux 2 (255MHz * 2) = fclk_div5 (matches exactly 510MHz) - mux 3 (182MHz * 2) = fclk_div7 (actual rate = 346.3MHz, off by 0.3MHz) [0] https://github.com/khadas/linux/blob/9587681285cb/drivers/amlogic/amlnf/dev/amlnf_ctrl.c#L314 Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
2018-04-23 19:35:09 +00:00
&meson8b_nand_clk_sel,
&meson8b_nand_clk_div,
&meson8b_nand_clk_gate,
&meson8b_fixed_pll_dco,
&meson8b_vid_pll_dco,
&meson8b_sys_pll_dco,
};
static const struct meson8b_clk_reset_line {
u32 reg;
u8 bit_idx;
} meson8b_clk_reset_bits[] = {
[CLKC_RESET_L2_CACHE_SOFT_RESET] = {
.reg = HHI_SYS_CPU_CLK_CNTL0, .bit_idx = 30
},
[CLKC_RESET_AXI_64_TO_128_BRIDGE_A5_SOFT_RESET] = {
.reg = HHI_SYS_CPU_CLK_CNTL0, .bit_idx = 29
},
[CLKC_RESET_SCU_SOFT_RESET] = {
.reg = HHI_SYS_CPU_CLK_CNTL0, .bit_idx = 28
},
[CLKC_RESET_CPU3_SOFT_RESET] = {
.reg = HHI_SYS_CPU_CLK_CNTL0, .bit_idx = 27
},
[CLKC_RESET_CPU2_SOFT_RESET] = {
.reg = HHI_SYS_CPU_CLK_CNTL0, .bit_idx = 26
},
[CLKC_RESET_CPU1_SOFT_RESET] = {
.reg = HHI_SYS_CPU_CLK_CNTL0, .bit_idx = 25
},
[CLKC_RESET_CPU0_SOFT_RESET] = {
.reg = HHI_SYS_CPU_CLK_CNTL0, .bit_idx = 24
},
[CLKC_RESET_A5_GLOBAL_RESET] = {
.reg = HHI_SYS_CPU_CLK_CNTL0, .bit_idx = 18
},
[CLKC_RESET_A5_AXI_SOFT_RESET] = {
.reg = HHI_SYS_CPU_CLK_CNTL0, .bit_idx = 17
},
[CLKC_RESET_A5_ABP_SOFT_RESET] = {
.reg = HHI_SYS_CPU_CLK_CNTL0, .bit_idx = 16
},
[CLKC_RESET_AXI_64_TO_128_BRIDGE_MMC_SOFT_RESET] = {
.reg = HHI_SYS_CPU_CLK_CNTL1, .bit_idx = 30
},
[CLKC_RESET_VID_CLK_CNTL_SOFT_RESET] = {
.reg = HHI_VID_CLK_CNTL, .bit_idx = 15
},
[CLKC_RESET_VID_DIVIDER_CNTL_SOFT_RESET_POST] = {
.reg = HHI_VID_DIVIDER_CNTL, .bit_idx = 7
},
[CLKC_RESET_VID_DIVIDER_CNTL_SOFT_RESET_PRE] = {
.reg = HHI_VID_DIVIDER_CNTL, .bit_idx = 3
},
[CLKC_RESET_VID_DIVIDER_CNTL_RESET_N_POST] = {
.reg = HHI_VID_DIVIDER_CNTL, .bit_idx = 1
},
[CLKC_RESET_VID_DIVIDER_CNTL_RESET_N_PRE] = {
.reg = HHI_VID_DIVIDER_CNTL, .bit_idx = 0
},
};
static int meson8b_clk_reset_update(struct reset_controller_dev *rcdev,
unsigned long id, bool assert)
{
struct meson8b_clk_reset *meson8b_clk_reset =
container_of(rcdev, struct meson8b_clk_reset, reset);
unsigned long flags;
const struct meson8b_clk_reset_line *reset;
if (id >= ARRAY_SIZE(meson8b_clk_reset_bits))
return -EINVAL;
reset = &meson8b_clk_reset_bits[id];
spin_lock_irqsave(&meson_clk_lock, flags);
if (assert)
regmap_update_bits(meson8b_clk_reset->regmap, reset->reg,
BIT(reset->bit_idx), BIT(reset->bit_idx));
else
regmap_update_bits(meson8b_clk_reset->regmap, reset->reg,
BIT(reset->bit_idx), 0);
spin_unlock_irqrestore(&meson_clk_lock, flags);
return 0;
}
static int meson8b_clk_reset_assert(struct reset_controller_dev *rcdev,
unsigned long id)
{
return meson8b_clk_reset_update(rcdev, id, true);
}
static int meson8b_clk_reset_deassert(struct reset_controller_dev *rcdev,
unsigned long id)
{
return meson8b_clk_reset_update(rcdev, id, false);
}
static const struct reset_control_ops meson8b_clk_reset_ops = {
.assert = meson8b_clk_reset_assert,
.deassert = meson8b_clk_reset_deassert,
};
static const struct regmap_config clkc_regmap_config = {
.reg_bits = 32,
.val_bits = 32,
.reg_stride = 4,
};
static void __init meson8b_clkc_init(struct device_node *np)
{
struct meson8b_clk_reset *rstc;
void __iomem *clk_base;
struct regmap *map;
int i, ret;
map = syscon_node_to_regmap(of_get_parent(np));
if (IS_ERR(map)) {
pr_info("failed to get HHI regmap - Trying obsolete regs\n");
/* Generic clocks, PLLs and some of the reset-bits */
clk_base = of_iomap(np, 1);
if (!clk_base) {
pr_err("%s: Unable to map clk base\n", __func__);
return;
}
map = regmap_init_mmio(NULL, clk_base, &clkc_regmap_config);
if (IS_ERR(map))
return;
}
rstc = kzalloc(sizeof(*rstc), GFP_KERNEL);
if (!rstc)
return;
/* Reset Controller */
rstc->regmap = map;
rstc->reset.ops = &meson8b_clk_reset_ops;
rstc->reset.nr_resets = ARRAY_SIZE(meson8b_clk_reset_bits);
rstc->reset.of_node = np;
ret = reset_controller_register(&rstc->reset);
if (ret) {
pr_err("%s: Failed to register clkc reset controller: %d\n",
__func__, ret);
return;
}
/* Populate regmap for the regmap backed clocks */
for (i = 0; i < ARRAY_SIZE(meson8b_clk_regmaps); i++)
meson8b_clk_regmaps[i]->map = map;
/*
* register all clks
* CLKID_UNUSED = 0, so skip it and start with CLKID_XTAL = 1
*/
for (i = CLKID_XTAL; i < CLK_NR_CLKS; i++) {
/* array might be sparse */
if (!meson8b_hw_onecell_data.hws[i])
continue;
ret = clk_hw_register(NULL, meson8b_hw_onecell_data.hws[i]);
if (ret)
return;
}
ret = of_clk_add_hw_provider(np, of_clk_hw_onecell_get,
&meson8b_hw_onecell_data);
if (ret)
pr_err("%s: failed to register clock provider\n", __func__);
}
CLK_OF_DECLARE_DRIVER(meson8_clkc, "amlogic,meson8-clkc",
meson8b_clkc_init);
CLK_OF_DECLARE_DRIVER(meson8b_clkc, "amlogic,meson8b-clkc",
meson8b_clkc_init);
CLK_OF_DECLARE_DRIVER(meson8m2_clkc, "amlogic,meson8m2-clkc",
meson8b_clkc_init);