forked from Minki/linux
55 lines
1.4 KiB
Plaintext
55 lines
1.4 KiB
Plaintext
|
NXP LPC18xx/43xx DMA MUX (DMA request router)
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: "nxp,lpc1850-dmamux"
|
||
|
|
- reg: Memory map for accessing module
|
||
|
|
- #dma-cells: Should be set to <3>.
|
||
|
|
* 1st cell contain the master dma request signal
|
||
|
|
* 2nd cell contain the mux value (0-3) for the peripheral
|
||
|
|
* 3rd cell contain either 1 or 2 depending on the AHB
|
||
|
|
master used.
|
||
|
|
- dma-requests: Number of DMA requests for the mux
|
||
|
|
- dma-masters: phandle pointing to the DMA controller
|
||
|
|
|
||
|
|
The DMA controller node need to have the following poroperties:
|
||
|
|
- dma-requests: Number of DMA requests the controller can handle
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
dmac: dma@40002000 {
|
||
|
|
compatible = "nxp,lpc1850-gpdma", "arm,pl080", "arm,primecell";
|
||
|
|
arm,primecell-periphid = <0x00041080>;
|
||
|
|
reg = <0x40002000 0x1000>;
|
||
|
|
interrupts = <2>;
|
||
|
|
clocks = <&ccu1 CLK_CPU_DMA>;
|
||
|
|
clock-names = "apb_pclk";
|
||
|
|
#dma-cells = <2>;
|
||
|
|
dma-channels = <8>;
|
||
|
|
dma-requests = <16>;
|
||
|
|
lli-bus-interface-ahb1;
|
||
|
|
lli-bus-interface-ahb2;
|
||
|
|
mem-bus-interface-ahb1;
|
||
|
|
mem-bus-interface-ahb2;
|
||
|
|
memcpy-burst-size = <256>;
|
||
|
|
memcpy-bus-width = <32>;
|
||
|
|
};
|
||
|
|
|
||
|
|
dmamux: dma-mux {
|
||
|
|
compatible = "nxp,lpc1850-dmamux";
|
||
|
|
#dma-cells = <3>;
|
||
|
|
dma-requests = <64>;
|
||
|
|
dma-masters = <&dmac>;
|
||
|
|
};
|
||
|
|
|
||
|
|
uart0: serial@40081000 {
|
||
|
|
compatible = "nxp,lpc1850-uart", "ns16550a";
|
||
|
|
reg = <0x40081000 0x1000>;
|
||
|
|
reg-shift = <2>;
|
||
|
|
interrupts = <24>;
|
||
|
|
clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>;
|
||
|
|
clock-names = "uartclk", "reg";
|
||
|
|
dmas = <&dmamux 1 1 2
|
||
|
|
&dmamux 2 1 2>;
|
||
|
|
dma-names = "tx", "rx";
|
||
|
|
};
|