leandrof/linux
1
0
Fork 0
forked from Minki/linux
Code Issues Pull Requests Packages Projects Releases Wiki Activity
c91ec5f3ad
linux/drivers/net/usb/qmi_wwan.c

480 lines
17 KiB
C
Raw Normal View History

net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
/*
* Copyright (c) 2012 Bjørn Mork <bjorn@mork.no>
*
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
* The probing code is heavily inspired by cdc_ether, which is:
* Copyright (C) 2003-2005 by David Brownell
* Copyright (C) 2006 by Ole Andre Vadla Ravnas (ActiveSync)
*
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*/
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/ethtool.h>
#include <linux/mii.h>
#include <linux/usb.h>
#include <linux/usb/cdc.h>
#include <linux/usb/usbnet.h>
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
#include <linux/usb/cdc-wdm.h>
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
/* This driver supports wwan (3G/LTE/?) devices using a vendor
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
* specific management protocol called Qualcomm MSM Interface (QMI) -
* in addition to the more common AT commands over serial interface
* management
*
* QMI is wrapped in CDC, using CDC encapsulated commands on the
* control ("master") interface of a two-interface CDC Union
* resembling standard CDC ECM. The devices do not use the control
* interface for any other CDC messages. Most likely because the
* management protocol is used in place of the standard CDC
* notifications NOTIFY_NETWORK_CONNECTION and NOTIFY_SPEED_CHANGE
*
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
* Alternatively, control and data functions can be combined in a
* single USB interface.
*
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
* Handling a protocol like QMI is out of the scope for any driver.
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
* It is exported as a character device using the cdc-wdm driver as
* a subdriver, enabling userspace applications ("modem managers") to
* handle it.
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
*
* These devices may alternatively/additionally be configured using AT
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
* commands on a serial interface
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
*/
net: qmi_wwan: define a structure for driver specific state usbnet allocates a fixed size array for minidriver specific state. Naming the fields and taking advantage of type checking is a bit more failsafe than casting array elements each time they are referenced. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:41:59 +00:00
/* driver specific data */
struct qmi_wwan_state {
struct usb_driver *subdriver;
atomic_t pmcount;
net: qmi_wwan: rearranging to prepare for code sharing Most of the subdriver registration code can be reused for devices with separate control and data interfaces. Move the code a bit around to prepare for such reuse. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:00 +00:00
unsigned long unused;
struct usb_interface *control;
struct usb_interface *data;
net: qmi_wwan: define a structure for driver specific state usbnet allocates a fixed size array for minidriver specific state. Naming the fields and taking advantage of type checking is a bit more failsafe than casting array elements each time they are referenced. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:41:59 +00:00
};
net: qmi_wwan: rearranging to prepare for code sharing Most of the subdriver registration code can be reused for devices with separate control and data interfaces. Move the code a bit around to prepare for such reuse. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:00 +00:00
/* using a counter to merge subdriver requests with our own into a combined state */
static int qmi_wwan_manage_power(struct usbnet *dev, int on)
{
struct qmi_wwan_state *info = (void *)&dev->data;
int rv = 0;
dev_dbg(&dev->intf->dev, "%s() pmcount=%d, on=%d\n", __func__, atomic_read(&info->pmcount), on);
if ((on && atomic_add_return(1, &info->pmcount) == 1) || (!on && atomic_dec_and_test(&info->pmcount))) {
/* need autopm_get/put here to ensure the usbcore sees the new value */
rv = usb_autopm_get_interface(dev->intf);
if (rv < 0)
goto err;
dev->intf->needs_remote_wakeup = on;
usb_autopm_put_interface(dev->intf);
}
err:
return rv;
}
static int qmi_wwan_cdc_wdm_manage_power(struct usb_interface *intf, int on)
{
struct usbnet *dev = usb_get_intfdata(intf);
Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net Conflicts: drivers/net/caif/caif_hsi.c drivers/net/usb/qmi_wwan.c The qmi_wwan merge was trivial. The caif_hsi.c, on the other hand, was not. It's a conflict between 1c385f1fdf6f9c66d982802cd74349c040980b50 ("caif-hsi: Replace platform device with ops structure.") in the net-next tree and commit 39abbaef19cd0a30be93794aa4773c779c3eb1f3 ("caif-hsi: Postpone init of HIS until open()") in the net tree. I did my best with that one and will ask Sjur to check it out. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-29 00:37:00 +00:00
/* can be called while disconnecting */
if (!dev)
return 0;
net: qmi_wwan: rearranging to prepare for code sharing Most of the subdriver registration code can be reused for devices with separate control and data interfaces. Move the code a bit around to prepare for such reuse. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:00 +00:00
return qmi_wwan_manage_power(dev, on);
}
/* collect all three endpoints and register subdriver */
static int qmi_wwan_register_subdriver(struct usbnet *dev)
{
int rv;
struct usb_driver *subdriver = NULL;
struct qmi_wwan_state *info = (void *)&dev->data;
/* collect bulk endpoints */
rv = usbnet_get_endpoints(dev, info->data);
if (rv < 0)
goto err;
/* update status endpoint if separate control interface */
if (info->control != info->data)
dev->status = &info->control->cur_altsetting->endpoint[0];
/* require interrupt endpoint for subdriver */
if (!dev->status) {
rv = -EINVAL;
goto err;
}
/* for subdriver power management */
atomic_set(&info->pmcount, 0);
/* register subdriver */
net: qmi_wwan: increase max QMI message size to 4096 QMI requests exceeding 1500 bytes are possible and device firmware does not handle fragmented messages very well. It is therefore necessary to increase the maximum message size from the current 512 bytes. The protocol message size limit is not documented in any publicly known source, but the out of tree driver from CodeAurora use 4 kB. This is therefore chosen as the new arbitrary default until the real limit is known. This should allow any QMI message to be transmitted without fragmentation, fixing known issues with GPS assistance data upload. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-07 07:36:06 +00:00
subdriver = usb_cdc_wdm_register(info->control, &dev->status->desc, 4096, &qmi_wwan_cdc_wdm_manage_power);
net: qmi_wwan: rearranging to prepare for code sharing Most of the subdriver registration code can be reused for devices with separate control and data interfaces. Move the code a bit around to prepare for such reuse. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:00 +00:00
if (IS_ERR(subdriver)) {
dev_err(&info->control->dev, "subdriver registration failed\n");
rv = PTR_ERR(subdriver);
goto err;
}
/* prevent usbnet from using status endpoint */
dev->status = NULL;
/* save subdriver struct for suspend/resume wrappers */
info->subdriver = subdriver;
err:
return rv;
}
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
static int qmi_wwan_bind(struct usbnet *dev, struct usb_interface *intf)
{
int status = -1;
u8 *buf = intf->cur_altsetting->extra;
int len = intf->cur_altsetting->extralen;
struct usb_interface_descriptor *desc = &intf->cur_altsetting->desc;
struct usb_cdc_union_desc *cdc_union = NULL;
struct usb_cdc_ether_desc *cdc_ether = NULL;
u32 found = 0;
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
struct usb_driver *driver = driver_of(intf);
net: qmi_wwan: define a structure for driver specific state usbnet allocates a fixed size array for minidriver specific state. Naming the fields and taking advantage of type checking is a bit more failsafe than casting array elements each time they are referenced. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:41:59 +00:00
struct qmi_wwan_state *info = (void *)&dev->data;
BUILD_BUG_ON((sizeof(((struct usbnet *)0)->data) < sizeof(struct qmi_wwan_state)));
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
net: qmi_wwan: use a single bind function for all device types Refactoring the bind code lets us use a common driver_info struct for all supported devices, simplifying the code a bit. The real advantage is that devices using the CDC ECM interface layout now also can be added dynamically using the new_id sysfs interface. This simplifies testing of new devices. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-07 07:36:07 +00:00
/* control and data is shared? */
if (intf->cur_altsetting->desc.bNumEndpoints == 3) {
info->control = intf;
info->data = intf;
goto shared;
}
/* else require a single interrupt status endpoint on control intf */
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
if (intf->cur_altsetting->desc.bNumEndpoints != 1)
goto err;
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
net: qmi_wwan: use a single bind function for all device types Refactoring the bind code lets us use a common driver_info struct for all supported devices, simplifying the code a bit. The real advantage is that devices using the CDC ECM interface layout now also can be added dynamically using the new_id sysfs interface. This simplifies testing of new devices. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-07 07:36:07 +00:00
/* and a number of CDC descriptors */
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
while (len > 3) {
struct usb_descriptor_header *h = (void *)buf;
/* ignore any misplaced descriptors */
if (h->bDescriptorType != USB_DT_CS_INTERFACE)
goto next_desc;
/* buf[2] is CDC descriptor subtype */
switch (buf[2]) {
case USB_CDC_HEADER_TYPE:
if (found & 1 << USB_CDC_HEADER_TYPE) {
dev_dbg(&intf->dev, "extra CDC header\n");
goto err;
}
if (h->bLength != sizeof(struct usb_cdc_header_desc)) {
dev_dbg(&intf->dev, "CDC header len %u\n", h->bLength);
goto err;
}
break;
case USB_CDC_UNION_TYPE:
if (found & 1 << USB_CDC_UNION_TYPE) {
dev_dbg(&intf->dev, "extra CDC union\n");
goto err;
}
if (h->bLength != sizeof(struct usb_cdc_union_desc)) {
dev_dbg(&intf->dev, "CDC union len %u\n", h->bLength);
goto err;
}
cdc_union = (struct usb_cdc_union_desc *)buf;
break;
case USB_CDC_ETHERNET_TYPE:
if (found & 1 << USB_CDC_ETHERNET_TYPE) {
dev_dbg(&intf->dev, "extra CDC ether\n");
goto err;
}
if (h->bLength != sizeof(struct usb_cdc_ether_desc)) {
dev_dbg(&intf->dev, "CDC ether len %u\n", h->bLength);
goto err;
}
cdc_ether = (struct usb_cdc_ether_desc *)buf;
break;
}
/*
* Remember which CDC functional descriptors we've seen. Works
* for all types we care about, of which USB_CDC_ETHERNET_TYPE
* (0x0f) is the highest numbered
*/
if (buf[2] < 32)
found |= 1 << buf[2];
next_desc:
len -= h->bLength;
buf += h->bLength;
}
/* did we find all the required ones? */
net: qmi_wwan: simplify a check in qmi_wwan_bind() This code is easier to read if we specify which flags we want at the condition instead of at the top of the function. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-25 22:39:45 +00:00
if (!(found & (1 << USB_CDC_HEADER_TYPE)) ||
!(found & (1 << USB_CDC_UNION_TYPE))) {
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
dev_err(&intf->dev, "CDC functional descriptors missing\n");
goto err;
}
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
/* verify CDC Union */
if (desc->bInterfaceNumber != cdc_union->bMasterInterface0) {
dev_err(&intf->dev, "bogus CDC Union: master=%u\n", cdc_union->bMasterInterface0);
goto err;
}
/* need to save these for unbind */
info->control = intf;
info->data = usb_ifnum_to_if(dev->udev, cdc_union->bSlaveInterface0);
if (!info->data) {
dev_err(&intf->dev, "bogus CDC Union: slave=%u\n", cdc_union->bSlaveInterface0);
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
goto err;
}
/* errors aren't fatal - we can live with the dynamic address */
if (cdc_ether) {
dev->hard_mtu = le16_to_cpu(cdc_ether->wMaxSegmentSize);
usbnet_get_ethernet_addr(dev, cdc_ether->iMACAddress);
}
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
/* claim data interface and set it up */
status = usb_driver_claim_interface(driver, info->data, dev);
if (status < 0)
goto err;
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
net: qmi_wwan: use a single bind function for all device types Refactoring the bind code lets us use a common driver_info struct for all supported devices, simplifying the code a bit. The real advantage is that devices using the CDC ECM interface layout now also can be added dynamically using the new_id sysfs interface. This simplifies testing of new devices. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-07 07:36:07 +00:00
shared:
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
status = qmi_wwan_register_subdriver(dev);
net: qmi_wwan: use a single bind function for all device types Refactoring the bind code lets us use a common driver_info struct for all supported devices, simplifying the code a bit. The real advantage is that devices using the CDC ECM interface layout now also can be added dynamically using the new_id sysfs interface. This simplifies testing of new devices. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-07 07:36:07 +00:00
if (status < 0 && info->control != info->data) {
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
usb_set_intfdata(info->data, NULL);
usb_driver_release_interface(driver, info->data);
}
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
err:
return status;
}
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
static void qmi_wwan_unbind(struct usbnet *dev, struct usb_interface *intf)
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
{
net: qmi_wwan: define a structure for driver specific state usbnet allocates a fixed size array for minidriver specific state. Naming the fields and taking advantage of type checking is a bit more failsafe than casting array elements each time they are referenced. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:41:59 +00:00
struct qmi_wwan_state *info = (void *)&dev->data;
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
struct usb_driver *driver = driver_of(intf);
struct usb_interface *other;
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
net: qmi_wwan: define a structure for driver specific state usbnet allocates a fixed size array for minidriver specific state. Naming the fields and taking advantage of type checking is a bit more failsafe than casting array elements each time they are referenced. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:41:59 +00:00
if (info->subdriver && info->subdriver->disconnect)
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
info->subdriver->disconnect(info->control);
/* allow user to unbind using either control or data */
if (intf == info->control)
other = info->data;
else
other = info->control;
/* only if not shared */
if (other && intf != other) {
usb_set_intfdata(other, NULL);
usb_driver_release_interface(driver, other);
}
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
net: qmi_wwan: define a structure for driver specific state usbnet allocates a fixed size array for minidriver specific state. Naming the fields and taking advantage of type checking is a bit more failsafe than casting array elements each time they are referenced. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:41:59 +00:00
info->subdriver = NULL;
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
info->data = NULL;
info->control = NULL;
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
}
/* suspend/resume wrappers calling both usbnet and the cdc-wdm
* subdriver if present.
*
* NOTE: cdc-wdm also supports pre/post_reset, but we cannot provide
* wrappers for those without adding usbnet reset support first.
*/
static int qmi_wwan_suspend(struct usb_interface *intf, pm_message_t message)
{
struct usbnet *dev = usb_get_intfdata(intf);
net: qmi_wwan: define a structure for driver specific state usbnet allocates a fixed size array for minidriver specific state. Naming the fields and taking advantage of type checking is a bit more failsafe than casting array elements each time they are referenced. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:41:59 +00:00
struct qmi_wwan_state *info = (void *)&dev->data;
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
int ret;
ret = usbnet_suspend(intf, message);
if (ret < 0)
goto err;
net: qmi_wwan: call subdriver with control intf only This fixes a hang on suspend due to calling wdm_suspend on the unregistered data interface. The hang should have been a NULL pointer reference had it not been for a logic error in the cdc_wdm code. commit 230718bd net: qmi_wwan: bind to both control and data interface changed qmi_wwan to use cdc_wdm as a subdriver for devices with a two-interface QMI/wwan function. The commit failed to update qmi_wwan_suspend and qmi_wwan_resume, which were written to handle either a single combined interface function, or no subdriver at all. The result was that we called into the subdriver both when the control interface was suspended and when the data interface was suspended. Calling the subdriver suspend function with an unregistered interface is not supported and will make the subdriver bug out. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-12 20:44:35 +00:00
if (intf == info->control && info->subdriver && info->subdriver->suspend)
net: qmi_wwan: define a structure for driver specific state usbnet allocates a fixed size array for minidriver specific state. Naming the fields and taking advantage of type checking is a bit more failsafe than casting array elements each time they are referenced. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:41:59 +00:00
ret = info->subdriver->suspend(intf, message);
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
if (ret < 0)
usbnet_resume(intf);
err:
return ret;
}
static int qmi_wwan_resume(struct usb_interface *intf)
{
struct usbnet *dev = usb_get_intfdata(intf);
net: qmi_wwan: define a structure for driver specific state usbnet allocates a fixed size array for minidriver specific state. Naming the fields and taking advantage of type checking is a bit more failsafe than casting array elements each time they are referenced. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:41:59 +00:00
struct qmi_wwan_state *info = (void *)&dev->data;
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
int ret = 0;
net: qmi_wwan: call subdriver with control intf only This fixes a hang on suspend due to calling wdm_suspend on the unregistered data interface. The hang should have been a NULL pointer reference had it not been for a logic error in the cdc_wdm code. commit 230718bd net: qmi_wwan: bind to both control and data interface changed qmi_wwan to use cdc_wdm as a subdriver for devices with a two-interface QMI/wwan function. The commit failed to update qmi_wwan_suspend and qmi_wwan_resume, which were written to handle either a single combined interface function, or no subdriver at all. The result was that we called into the subdriver both when the control interface was suspended and when the data interface was suspended. Calling the subdriver suspend function with an unregistered interface is not supported and will make the subdriver bug out. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-12 20:44:35 +00:00
bool callsub = (intf == info->control && info->subdriver && info->subdriver->resume);
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
net: qmi_wwan: call subdriver with control intf only This fixes a hang on suspend due to calling wdm_suspend on the unregistered data interface. The hang should have been a NULL pointer reference had it not been for a logic error in the cdc_wdm code. commit 230718bd net: qmi_wwan: bind to both control and data interface changed qmi_wwan to use cdc_wdm as a subdriver for devices with a two-interface QMI/wwan function. The commit failed to update qmi_wwan_suspend and qmi_wwan_resume, which were written to handle either a single combined interface function, or no subdriver at all. The result was that we called into the subdriver both when the control interface was suspended and when the data interface was suspended. Calling the subdriver suspend function with an unregistered interface is not supported and will make the subdriver bug out. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-12 20:44:35 +00:00
if (callsub)
net: qmi_wwan: define a structure for driver specific state usbnet allocates a fixed size array for minidriver specific state. Naming the fields and taking advantage of type checking is a bit more failsafe than casting array elements each time they are referenced. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:41:59 +00:00
ret = info->subdriver->resume(intf);
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
if (ret < 0)
goto err;
ret = usbnet_resume(intf);
net: qmi_wwan: call subdriver with control intf only This fixes a hang on suspend due to calling wdm_suspend on the unregistered data interface. The hang should have been a NULL pointer reference had it not been for a logic error in the cdc_wdm code. commit 230718bd net: qmi_wwan: bind to both control and data interface changed qmi_wwan to use cdc_wdm as a subdriver for devices with a two-interface QMI/wwan function. The commit failed to update qmi_wwan_suspend and qmi_wwan_resume, which were written to handle either a single combined interface function, or no subdriver at all. The result was that we called into the subdriver both when the control interface was suspended and when the data interface was suspended. Calling the subdriver suspend function with an unregistered interface is not supported and will make the subdriver bug out. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-12 20:44:35 +00:00
if (ret < 0 && callsub && info->subdriver->suspend)
net: qmi_wwan: define a structure for driver specific state usbnet allocates a fixed size array for minidriver specific state. Naming the fields and taking advantage of type checking is a bit more failsafe than casting array elements each time they are referenced. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:41:59 +00:00
info->subdriver->suspend(intf, PMSG_SUSPEND);
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
err:
return ret;
}
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
static const struct driver_info qmi_wwan_info = {
net: qmi_wwan: shorten driver description The description is used in ethtool fixed length fields. Make it shorter to avoid truncation. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:02 +00:00
.description = "WWAN/QMI device",
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
.flags = FLAG_WWAN,
.bind = qmi_wwan_bind,
net: qmi_wwan: bind to both control and data interface Always bind to control interface regardless of whether it is a shared interface or not. A QMI/wwan function is required to provide both a control interface (QMI) and a data interface (wwan). All devices supported by this driver do so. But the vendors may choose to use different USB descriptor layouts, and some vendors even allow the same device to present different layouts. Most of these devices use a USB descriptor layout with a single USB interface for both control and data. But some split control and data into two interfaces, bound together by a CDC Union descriptor on the control interface. Before the cdc-wdm subdriver support was added, this split was used to let cdc-wdm drive the QMI control interface and qmi_wwan drive the wwna data interface. This split driver model has a number of issues: - qmi_wwan must match on the data interface descriptor, which often are indistiguishable from data interfaces belonging to other CDC (like) functions like ACM - supporting a single QMI/wwan function requires adding the device to two drivers - syncronizing the probes among a number of drivers, to ensure selecting the correct driver, is difficult unless all drivers match on the same interface This patch resolves these problems by using the same probing mechanism as cdc-ether for devices with a two- interface USB descriptor layout. This makes the driver behave consistently, supporting both the control and data part of the QMI/wwan function, regardless of the USB descriptors. Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:01 +00:00
.unbind = qmi_wwan_unbind,
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
.manage_power = qmi_wwan_manage_power,
};
#define HUAWEI_VENDOR_ID 0x12D1
net: qmi_wwan: fix Gobi device probing Ignoring interfaces with additional descriptors is not a reliable method for locating the correct interface on Gobi devices. There is at least one device where this method fails: https://bbs.archlinux.org/viewtopic.php?id=143506 The result is that the AT command port (interface #2) is hidden from qcserial, preventing traditional serial modem usage: [ 15.562552] qmi_wwan 4-1.6:1.0: cdc-wdm0: USB WDM device [ 15.562691] qmi_wwan 4-1.6:1.0: wwan0: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b [ 15.563383] qmi_wwan: probe of 4-1.6:1.1 failed with error -22 [ 15.564189] qmi_wwan 4-1.6:1.2: cdc-wdm1: USB WDM device [ 15.564302] qmi_wwan 4-1.6:1.2: wwan1: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b [ 15.564328] qmi_wwan: probe of 4-1.6:1.3 failed with error -22 [ 15.569376] qcserial 4-1.6:1.1: Qualcomm USB modem converter detected [ 15.569440] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB0 [ 15.570372] qcserial 4-1.6:1.3: Qualcomm USB modem converter detected [ 15.570430] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB1 Use static interface numbers taken from the interface map in qcserial for all Gobi devices instead: Gobi 1K USB layout: 0: serial port (doesn't respond) 1: serial port (doesn't respond) 2: AT-capable modem port 3: QMI/net Gobi 2K+ USB layout: 0: QMI/net 1: DM/DIAG (use libqcdm from ModemManager for communication) 2: AT-capable modem port 3: NMEA This should be more reliable over all, and will also prevent the noisy "probe failed" messages. The whitelisting logic is expected to be replaced by direct interface number matching in 3.6. Reported-by: Heinrich Siebmanns (Harvey) <H.Siebmanns@t-online.de> Cc: <stable@vger.kernel.org> # v3.4: 0000188 USB: qmi_wwan: Make forced int 4 whitelist generic Cc: <stable@vger.kernel.org> # v3.4: f7142e6 USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z Cc: <stable@vger.kernel.org> # v3.4 Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-21 02:45:58 +00:00
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
/* map QMI/wwan function by a fixed interface number */
#define QMI_FIXED_INTF(vend, prod, num) \
USB_DEVICE_INTERFACE_NUMBER(vend, prod, num), \
net: qmi_wwan: use a single bind function for all device types Refactoring the bind code lets us use a common driver_info struct for all supported devices, simplifying the code a bit. The real advantage is that devices using the CDC ECM interface layout now also can be added dynamically using the new_id sysfs interface. This simplifies testing of new devices. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-07 07:36:07 +00:00
.driver_info = (unsigned long)&qmi_wwan_info
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
net: qmi_wwan: fix Gobi device probing Ignoring interfaces with additional descriptors is not a reliable method for locating the correct interface on Gobi devices. There is at least one device where this method fails: https://bbs.archlinux.org/viewtopic.php?id=143506 The result is that the AT command port (interface #2) is hidden from qcserial, preventing traditional serial modem usage: [ 15.562552] qmi_wwan 4-1.6:1.0: cdc-wdm0: USB WDM device [ 15.562691] qmi_wwan 4-1.6:1.0: wwan0: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b [ 15.563383] qmi_wwan: probe of 4-1.6:1.1 failed with error -22 [ 15.564189] qmi_wwan 4-1.6:1.2: cdc-wdm1: USB WDM device [ 15.564302] qmi_wwan 4-1.6:1.2: wwan1: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b [ 15.564328] qmi_wwan: probe of 4-1.6:1.3 failed with error -22 [ 15.569376] qcserial 4-1.6:1.1: Qualcomm USB modem converter detected [ 15.569440] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB0 [ 15.570372] qcserial 4-1.6:1.3: Qualcomm USB modem converter detected [ 15.570430] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB1 Use static interface numbers taken from the interface map in qcserial for all Gobi devices instead: Gobi 1K USB layout: 0: serial port (doesn't respond) 1: serial port (doesn't respond) 2: AT-capable modem port 3: QMI/net Gobi 2K+ USB layout: 0: QMI/net 1: DM/DIAG (use libqcdm from ModemManager for communication) 2: AT-capable modem port 3: NMEA This should be more reliable over all, and will also prevent the noisy "probe failed" messages. The whitelisting logic is expected to be replaced by direct interface number matching in 3.6. Reported-by: Heinrich Siebmanns (Harvey) <H.Siebmanns@t-online.de> Cc: <stable@vger.kernel.org> # v3.4: 0000188 USB: qmi_wwan: Make forced int 4 whitelist generic Cc: <stable@vger.kernel.org> # v3.4: f7142e6 USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z Cc: <stable@vger.kernel.org> # v3.4 Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-21 02:45:58 +00:00
/* Gobi 1000 QMI/wwan interface number is 3 according to qcserial */
#define QMI_GOBI1K_DEVICE(vend, prod) \
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
QMI_FIXED_INTF(vend, prod, 3)
net: qmi_wwan: fix Gobi device probing Ignoring interfaces with additional descriptors is not a reliable method for locating the correct interface on Gobi devices. There is at least one device where this method fails: https://bbs.archlinux.org/viewtopic.php?id=143506 The result is that the AT command port (interface #2) is hidden from qcserial, preventing traditional serial modem usage: [ 15.562552] qmi_wwan 4-1.6:1.0: cdc-wdm0: USB WDM device [ 15.562691] qmi_wwan 4-1.6:1.0: wwan0: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b [ 15.563383] qmi_wwan: probe of 4-1.6:1.1 failed with error -22 [ 15.564189] qmi_wwan 4-1.6:1.2: cdc-wdm1: USB WDM device [ 15.564302] qmi_wwan 4-1.6:1.2: wwan1: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b [ 15.564328] qmi_wwan: probe of 4-1.6:1.3 failed with error -22 [ 15.569376] qcserial 4-1.6:1.1: Qualcomm USB modem converter detected [ 15.569440] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB0 [ 15.570372] qcserial 4-1.6:1.3: Qualcomm USB modem converter detected [ 15.570430] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB1 Use static interface numbers taken from the interface map in qcserial for all Gobi devices instead: Gobi 1K USB layout: 0: serial port (doesn't respond) 1: serial port (doesn't respond) 2: AT-capable modem port 3: QMI/net Gobi 2K+ USB layout: 0: QMI/net 1: DM/DIAG (use libqcdm from ModemManager for communication) 2: AT-capable modem port 3: NMEA This should be more reliable over all, and will also prevent the noisy "probe failed" messages. The whitelisting logic is expected to be replaced by direct interface number matching in 3.6. Reported-by: Heinrich Siebmanns (Harvey) <H.Siebmanns@t-online.de> Cc: <stable@vger.kernel.org> # v3.4: 0000188 USB: qmi_wwan: Make forced int 4 whitelist generic Cc: <stable@vger.kernel.org> # v3.4: f7142e6 USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z Cc: <stable@vger.kernel.org> # v3.4 Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-21 02:45:58 +00:00
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
/* Gobi 2000/3000 QMI/wwan interface number is 0 according to qcserial */
net: qmi_wwan: add Gobi and Pantech UML290 device IDs Adding the Pantech UML290 and all non-QDL Gobi device IDs from the qcserial driver now that we have support for shared net/QMI USB interfaces. Most of these are not yet tested with this driver, but should be mostly identical to tested devices, except for device IDs. Gobi devices provide several different interfaces (serial/net/other) using the exact same class, subclass and protocol values. This driver will only support the net/QMI function while there are other drivers supporting other device functions. The net/QMI interface number may also differ from device to device. It has been noted that all the other interfaces have additional functional descriptors, so we use that to detect the interface supported by this driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:06 +00:00
#define QMI_GOBI_DEVICE(vend, prod) \
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
QMI_FIXED_INTF(vend, prod, 0)
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
static const struct usb_device_id products[] = {
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
/* 1. CDC ECM like devices match on the control interface */
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
{ /* Huawei E392, E398 and possibly others sharing both device id and more... */
net: qmi_wwan: compress device_id list using macros Take advantage of the matching macros to make the device id list easier to read and maintain. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:32 +00:00
USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 1, 9),
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
.driver_info = (unsigned long)&qmi_wwan_info,
},
net: qmi_wwan: Add Vodafone/Huawei K5005 support Tested-by: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-19 07:20:31 +00:00
{ /* Vodafone/Huawei K5005 (12d1:14c8) and similar modems */
net: qmi_wwan: compress device_id list using macros Take advantage of the matching macros to make the device id list easier to read and maintain. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:32 +00:00
USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 1, 57),
net: qmi_wwan: Add Vodafone/Huawei K5005 support Tested-by: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-19 07:20:31 +00:00
.driver_info = (unsigned long)&qmi_wwan_info,
},
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
/* 2. Combined interface devices matching on class+protocol */
net: qmi_wwan: adding Huawei E367, ZTE MF683 and Pantech P4200 One of the modes of Huawei E367 has this QMI/wwan interface: I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Huawei use subclass and protocol to identify vendor specific functions, so adding a new vendor rule for this combination. The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use the same subclass to identify the QMI/wwan function. Replace the existing device specific UML290 entries with generic vendor matching, adding support for the Pantech P4200. The ZTE MF683 has 6 vendor specific interfaces, all using ff/ff/ff for cls/sub/prot. Adding a match on interface #5 which is a QMI/wwan interface. Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com> Cc: Thomas Schäfer <tschaefer@t-online.de> Cc: Dan Williams <dcbw@redhat.com> Cc: Shawn J. Goff <shawn7400@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-19 10:03:36 +00:00
{ /* Huawei E367 and possibly others in "Windows mode" */
net: qmi_wwan: adding Huawei E367, ZTE MF683 and Pantech P4200 One of the modes of Huawei E367 has this QMI/wwan interface: I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Huawei use subclass and protocol to identify vendor specific functions, so adding a new vendor rule for this combination. The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use the same subclass to identify the QMI/wwan function. Replace the existing device specific UML290 entries with generic vendor matching, adding support for the Pantech P4200. The ZTE MF683 has 6 vendor specific interfaces, all using ff/ff/ff for cls/sub/prot. Adding a match on interface #5 which is a QMI/wwan interface. Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com> Cc: Thomas Schäfer <tschaefer@t-online.de> Cc: Dan Williams <dcbw@redhat.com> Cc: Shawn J. Goff <shawn7400@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-19 21:18:05 +00:00
USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 1, 7),
.driver_info = (unsigned long)&qmi_wwan_info,
},
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
{ /* Huawei E392, E398 and possibly others in "Windows mode" */
net: qmi_wwan: compress device_id list using macros Take advantage of the matching macros to make the device id list easier to read and maintain. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:32 +00:00
USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 1, 17),
net: qmi_wwan: use a single bind function for all device types Refactoring the bind code lets us use a common driver_info struct for all supported devices, simplifying the code a bit. The real advantage is that devices using the CDC ECM interface layout now also can be added dynamically using the new_id sysfs interface. This simplifies testing of new devices. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-07 07:36:07 +00:00
.driver_info = (unsigned long)&qmi_wwan_info,
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
},
net: qmi_wwan: adding Huawei E367, ZTE MF683 and Pantech P4200 One of the modes of Huawei E367 has this QMI/wwan interface: I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Huawei use subclass and protocol to identify vendor specific functions, so adding a new vendor rule for this combination. The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use the same subclass to identify the QMI/wwan function. Replace the existing device specific UML290 entries with generic vendor matching, adding support for the Pantech P4200. The ZTE MF683 has 6 vendor specific interfaces, all using ff/ff/ff for cls/sub/prot. Adding a match on interface #5 which is a QMI/wwan interface. Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com> Cc: Thomas Schäfer <tschaefer@t-online.de> Cc: Dan Williams <dcbw@redhat.com> Cc: Shawn J. Goff <shawn7400@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-19 10:03:36 +00:00
{ /* Pantech UML290, P4200 and more */
net: qmi_wwan: adding Huawei E367, ZTE MF683 and Pantech P4200 One of the modes of Huawei E367 has this QMI/wwan interface: I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Huawei use subclass and protocol to identify vendor specific functions, so adding a new vendor rule for this combination. The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use the same subclass to identify the QMI/wwan function. Replace the existing device specific UML290 entries with generic vendor matching, adding support for the Pantech P4200. The ZTE MF683 has 6 vendor specific interfaces, all using ff/ff/ff for cls/sub/prot. Adding a match on interface #5 which is a QMI/wwan interface. Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com> Cc: Thomas Schäfer <tschaefer@t-online.de> Cc: Dan Williams <dcbw@redhat.com> Cc: Shawn J. Goff <shawn7400@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-19 21:18:05 +00:00
USB_VENDOR_AND_INTERFACE_INFO(0x106c, USB_CLASS_VENDOR_SPEC, 0xf0, 0xff),
net: qmi_wwan: use a single bind function for all device types Refactoring the bind code lets us use a common driver_info struct for all supported devices, simplifying the code a bit. The real advantage is that devices using the CDC ECM interface layout now also can be added dynamically using the new_id sysfs interface. This simplifies testing of new devices. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-07 07:36:07 +00:00
.driver_info = (unsigned long)&qmi_wwan_info,
net: qmi_wwan: add Gobi and Pantech UML290 device IDs Adding the Pantech UML290 and all non-QDL Gobi device IDs from the qcserial driver now that we have support for shared net/QMI USB interfaces. Most of these are not yet tested with this driver, but should be mostly identical to tested devices, except for device IDs. Gobi devices provide several different interfaces (serial/net/other) using the exact same class, subclass and protocol values. This driver will only support the net/QMI function while there are other drivers supporting other device functions. The net/QMI interface number may also differ from device to device. It has been noted that all the other interfaces have additional functional descriptors, so we use that to detect the interface supported by this driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:06 +00:00
},
net: qmi_wwan: new devices: UML290 and K5006-Z Newer firmware versions for the Pantech UML290 use a different subclass ID. The Windows driver match on both IDs, so we do that as well. The ZTE (Vodafone) K5006-Z is a new device. Cc: Dan Williams <dcbw@redhat.com> Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-15 03:42:57 +00:00
{ /* Pantech UML290 - newer firmware */
net: qmi_wwan: adding Huawei E367, ZTE MF683 and Pantech P4200 One of the modes of Huawei E367 has this QMI/wwan interface: I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Huawei use subclass and protocol to identify vendor specific functions, so adding a new vendor rule for this combination. The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use the same subclass to identify the QMI/wwan function. Replace the existing device specific UML290 entries with generic vendor matching, adding support for the Pantech P4200. The ZTE MF683 has 6 vendor specific interfaces, all using ff/ff/ff for cls/sub/prot. Adding a match on interface #5 which is a QMI/wwan interface. Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com> Cc: Thomas Schäfer <tschaefer@t-online.de> Cc: Dan Williams <dcbw@redhat.com> Cc: Shawn J. Goff <shawn7400@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-19 21:18:05 +00:00
USB_VENDOR_AND_INTERFACE_INFO(0x106c, USB_CLASS_VENDOR_SPEC, 0xf1, 0xff),
net: qmi_wwan: use a single bind function for all device types Refactoring the bind code lets us use a common driver_info struct for all supported devices, simplifying the code a bit. The real advantage is that devices using the CDC ECM interface layout now also can be added dynamically using the new_id sysfs interface. This simplifies testing of new devices. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-07 07:36:07 +00:00
.driver_info = (unsigned long)&qmi_wwan_info,
net: qmi_wwan: new devices: UML290 and K5006-Z Newer firmware versions for the Pantech UML290 use a different subclass ID. The Windows driver match on both IDs, so we do that as well. The ZTE (Vodafone) K5006-Z is a new device. Cc: Dan Williams <dcbw@redhat.com> Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-15 03:42:57 +00:00
},
net: qmi_wwan: fix Gobi device probing Ignoring interfaces with additional descriptors is not a reliable method for locating the correct interface on Gobi devices. There is at least one device where this method fails: https://bbs.archlinux.org/viewtopic.php?id=143506 The result is that the AT command port (interface #2) is hidden from qcserial, preventing traditional serial modem usage: [ 15.562552] qmi_wwan 4-1.6:1.0: cdc-wdm0: USB WDM device [ 15.562691] qmi_wwan 4-1.6:1.0: wwan0: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b [ 15.563383] qmi_wwan: probe of 4-1.6:1.1 failed with error -22 [ 15.564189] qmi_wwan 4-1.6:1.2: cdc-wdm1: USB WDM device [ 15.564302] qmi_wwan 4-1.6:1.2: wwan1: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b [ 15.564328] qmi_wwan: probe of 4-1.6:1.3 failed with error -22 [ 15.569376] qcserial 4-1.6:1.1: Qualcomm USB modem converter detected [ 15.569440] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB0 [ 15.570372] qcserial 4-1.6:1.3: Qualcomm USB modem converter detected [ 15.570430] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB1 Use static interface numbers taken from the interface map in qcserial for all Gobi devices instead: Gobi 1K USB layout: 0: serial port (doesn't respond) 1: serial port (doesn't respond) 2: AT-capable modem port 3: QMI/net Gobi 2K+ USB layout: 0: QMI/net 1: DM/DIAG (use libqcdm from ModemManager for communication) 2: AT-capable modem port 3: NMEA This should be more reliable over all, and will also prevent the noisy "probe failed" messages. The whitelisting logic is expected to be replaced by direct interface number matching in 3.6. Reported-by: Heinrich Siebmanns (Harvey) <H.Siebmanns@t-online.de> Cc: <stable@vger.kernel.org> # v3.4: 0000188 USB: qmi_wwan: Make forced int 4 whitelist generic Cc: <stable@vger.kernel.org> # v3.4: f7142e6 USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z Cc: <stable@vger.kernel.org> # v3.4 Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-21 02:45:58 +00:00
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
/* 3. Combined interface devices matching on interface number */
{QMI_FIXED_INTF(0x19d2, 0x0055, 1)}, /* ZTE (Vodafone) K3520-Z */
{QMI_FIXED_INTF(0x19d2, 0x0063, 4)}, /* ZTE (Vodafone) K3565-Z */
{QMI_FIXED_INTF(0x19d2, 0x0104, 4)}, /* ZTE (Vodafone) K4505-Z */
net: qmi_wwan: adding Huawei E367, ZTE MF683 and Pantech P4200 One of the modes of Huawei E367 has this QMI/wwan interface: I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=07 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Huawei use subclass and protocol to identify vendor specific functions, so adding a new vendor rule for this combination. The Pantech devices UML290 (106c:3718) and P4200 (106c:3721) use the same subclass to identify the QMI/wwan function. Replace the existing device specific UML290 entries with generic vendor matching, adding support for the Pantech P4200. The ZTE MF683 has 6 vendor specific interfaces, all using ff/ff/ff for cls/sub/prot. Adding a match on interface #5 which is a QMI/wwan interface. Cc: Fangxiaozhi (Franko) <fangxiaozhi@huawei.com> Cc: Thomas Schäfer <tschaefer@t-online.de> Cc: Dan Williams <dcbw@redhat.com> Cc: Shawn J. Goff <shawn7400@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-19 21:18:05 +00:00
{QMI_FIXED_INTF(0x19d2, 0x0157, 5)}, /* ZTE MF683 */
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
{QMI_FIXED_INTF(0x19d2, 0x0167, 4)}, /* ZTE MF820D */
{QMI_FIXED_INTF(0x19d2, 0x0326, 4)}, /* ZTE MF821D */
{QMI_FIXED_INTF(0x19d2, 0x1008, 4)}, /* ZTE (Vodafone) K3570-Z */
{QMI_FIXED_INTF(0x19d2, 0x1010, 4)}, /* ZTE (Vodafone) K3571-Z */
net: qmi_wwan: new devices: UML290 and K5006-Z Newer firmware versions for the Pantech UML290 use a different subclass ID. The Windows driver match on both IDs, so we do that as well. The ZTE (Vodafone) K5006-Z is a new device. Cc: Dan Williams <dcbw@redhat.com> Cc: Thomas Schäfer <tschaefer@t-online.de> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-15 03:42:57 +00:00
{QMI_FIXED_INTF(0x19d2, 0x1018, 3)}, /* ZTE (Vodafone) K5006-Z */
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
{QMI_FIXED_INTF(0x19d2, 0x1402, 2)}, /* ZTE MF60 */
{QMI_FIXED_INTF(0x19d2, 0x2002, 4)}, /* ZTE (Vodafone) K3765-Z */
net: qmi_wwan: add Sierra Wireless devices Add 6 new devices and one modified device, based on information from laptop vendor Windows drivers. Sony provides a driver with two new devices using a Gobi 2k+ layout (1199:68a5 and 1199:68a9). The Sony driver also adds a non-standard QMI/net interface to the already supported 1199:9011 Gobi device. We do not know whether this is an alternate interface number or an additional interface which might be present, but that doesn't really matter. Lenovo provides a driver supporting 4 new devices: - MC7770 (1199:901b) with standard Gobi 2k+ layout - MC7700 (0f3d:68a2) with layout similar to MC7710 - MC7750 (114f:68a2) with layout similar to MC7710 - EM7700 (1199:901c) with layout similar to MC7710 Note regaring the three devices similar to MC7710: The Windows drivers only support interface #8 on these devices. The MC7710 can support QMI/net functions on interface #19 and #20 as well, and this driver is verified to work on interface #19 (a firmware bug is suspected to prevent #20 from working). We do not enable these additional interfaces until they either show up in a Windows driver or are verified to work in some other way. Therefore limiting the new devices to interface #8 for now. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:31 +00:00
{QMI_FIXED_INTF(0x0f3d, 0x68a2, 8)}, /* Sierra Wireless MC7700 */
{QMI_FIXED_INTF(0x114f, 0x68a2, 8)}, /* Sierra Wireless MC7750 */
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
{QMI_FIXED_INTF(0x1199, 0x68a2, 8)}, /* Sierra Wireless MC7710 in QMI mode */
{QMI_FIXED_INTF(0x1199, 0x68a2, 19)}, /* Sierra Wireless MC7710 in QMI mode */
net: qmi_wwan: add Sierra Wireless devices Add 6 new devices and one modified device, based on information from laptop vendor Windows drivers. Sony provides a driver with two new devices using a Gobi 2k+ layout (1199:68a5 and 1199:68a9). The Sony driver also adds a non-standard QMI/net interface to the already supported 1199:9011 Gobi device. We do not know whether this is an alternate interface number or an additional interface which might be present, but that doesn't really matter. Lenovo provides a driver supporting 4 new devices: - MC7770 (1199:901b) with standard Gobi 2k+ layout - MC7700 (0f3d:68a2) with layout similar to MC7710 - MC7750 (114f:68a2) with layout similar to MC7710 - EM7700 (1199:901c) with layout similar to MC7710 Note regaring the three devices similar to MC7710: The Windows drivers only support interface #8 on these devices. The MC7710 can support QMI/net functions on interface #19 and #20 as well, and this driver is verified to work on interface #19 (a firmware bug is suspected to prevent #20 from working). We do not enable these additional interfaces until they either show up in a Windows driver or are verified to work in some other way. Therefore limiting the new devices to interface #8 for now. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:31 +00:00
{QMI_FIXED_INTF(0x1199, 0x901c, 8)}, /* Sierra Wireless EM7700 */
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
/* 4. Gobi 1000 devices */
net: qmi_wwan: fix Gobi device probing Ignoring interfaces with additional descriptors is not a reliable method for locating the correct interface on Gobi devices. There is at least one device where this method fails: https://bbs.archlinux.org/viewtopic.php?id=143506 The result is that the AT command port (interface #2) is hidden from qcserial, preventing traditional serial modem usage: [ 15.562552] qmi_wwan 4-1.6:1.0: cdc-wdm0: USB WDM device [ 15.562691] qmi_wwan 4-1.6:1.0: wwan0: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b [ 15.563383] qmi_wwan: probe of 4-1.6:1.1 failed with error -22 [ 15.564189] qmi_wwan 4-1.6:1.2: cdc-wdm1: USB WDM device [ 15.564302] qmi_wwan 4-1.6:1.2: wwan1: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b [ 15.564328] qmi_wwan: probe of 4-1.6:1.3 failed with error -22 [ 15.569376] qcserial 4-1.6:1.1: Qualcomm USB modem converter detected [ 15.569440] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB0 [ 15.570372] qcserial 4-1.6:1.3: Qualcomm USB modem converter detected [ 15.570430] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB1 Use static interface numbers taken from the interface map in qcserial for all Gobi devices instead: Gobi 1K USB layout: 0: serial port (doesn't respond) 1: serial port (doesn't respond) 2: AT-capable modem port 3: QMI/net Gobi 2K+ USB layout: 0: QMI/net 1: DM/DIAG (use libqcdm from ModemManager for communication) 2: AT-capable modem port 3: NMEA This should be more reliable over all, and will also prevent the noisy "probe failed" messages. The whitelisting logic is expected to be replaced by direct interface number matching in 3.6. Reported-by: Heinrich Siebmanns (Harvey) <H.Siebmanns@t-online.de> Cc: <stable@vger.kernel.org> # v3.4: 0000188 USB: qmi_wwan: Make forced int 4 whitelist generic Cc: <stable@vger.kernel.org> # v3.4: f7142e6 USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z Cc: <stable@vger.kernel.org> # v3.4 Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-21 02:45:58 +00:00
{QMI_GOBI1K_DEVICE(0x05c6, 0x9212)}, /* Acer Gobi Modem Device */
{QMI_GOBI1K_DEVICE(0x03f0, 0x1f1d)}, /* HP un2400 Gobi Modem Device */
{QMI_GOBI1K_DEVICE(0x04da, 0x250d)}, /* Panasonic Gobi Modem device */
{QMI_GOBI1K_DEVICE(0x413c, 0x8172)}, /* Dell Gobi Modem device */
{QMI_GOBI1K_DEVICE(0x1410, 0xa001)}, /* Novatel Gobi Modem device */
{QMI_GOBI1K_DEVICE(0x0b05, 0x1776)}, /* Asus Gobi Modem device */
{QMI_GOBI1K_DEVICE(0x19d2, 0xfff3)}, /* ONDA Gobi Modem device */
{QMI_GOBI1K_DEVICE(0x05c6, 0x9001)}, /* Generic Gobi Modem device */
{QMI_GOBI1K_DEVICE(0x05c6, 0x9002)}, /* Generic Gobi Modem device */
{QMI_GOBI1K_DEVICE(0x05c6, 0x9202)}, /* Generic Gobi Modem device */
{QMI_GOBI1K_DEVICE(0x05c6, 0x9203)}, /* Generic Gobi Modem device */
{QMI_GOBI1K_DEVICE(0x05c6, 0x9222)}, /* Generic Gobi Modem device */
{QMI_GOBI1K_DEVICE(0x05c6, 0x9009)}, /* Generic Gobi Modem device */
net: qmi_wwan: use fixed interface number matching This driver support many composite USB devices where the interface class/subclass/protocol provides no information about the interface function. Interfaces with different functions may all use ff/ff/ff, like this example of a device with three serial interfaces and three QMI/wwan interfaces: T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1199 ProdID=68a2 Rev= 0.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=MC7710 S: SerialNumber=3581780xxxxxx C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms Instead of class/subclass/protocol the vendor use fixed interface numbers for each function, and the Windows drivers use these numbers to match driver and function. The driver has had its own interface number whitelisting code to simulate this functionality. Replace this with generic interface number matching now that the USB subsystem support is there. This - removes the need for a driver_info structure per interface number, - avoids running the probe function for unsupported interfaces, and - simplifies the code. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:30 +00:00
/* 5. Gobi 2000 and 3000 devices */
net: qmi_wwan: add Gobi and Pantech UML290 device IDs Adding the Pantech UML290 and all non-QDL Gobi device IDs from the qcserial driver now that we have support for shared net/QMI USB interfaces. Most of these are not yet tested with this driver, but should be mostly identical to tested devices, except for device IDs. Gobi devices provide several different interfaces (serial/net/other) using the exact same class, subclass and protocol values. This driver will only support the net/QMI function while there are other drivers supporting other device functions. The net/QMI interface number may also differ from device to device. It has been noted that all the other interfaces have additional functional descriptors, so we use that to detect the interface supported by this driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:06 +00:00
{QMI_GOBI_DEVICE(0x413c, 0x8186)}, /* Dell Gobi 2000 Modem device (N0218, VU936) */
net: qmi_wwan: add several new Gobi devices Gobi devices are composite, needing both the qcserial and qmi_wwan drivers to support all functions. Re-syncing the list of supported devices with qcserial. Cc: Aleksander Morgado <aleksander@lanedo.com> Cc: Thomas Tuttle <ttuttle@chromium.org> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@tempietto.lan>
2012-09-01 03:47:26 +00:00
{QMI_GOBI_DEVICE(0x413c, 0x8194)}, /* Dell Gobi 3000 Composite */
net: qmi_wwan: add Gobi and Pantech UML290 device IDs Adding the Pantech UML290 and all non-QDL Gobi device IDs from the qcserial driver now that we have support for shared net/QMI USB interfaces. Most of these are not yet tested with this driver, but should be mostly identical to tested devices, except for device IDs. Gobi devices provide several different interfaces (serial/net/other) using the exact same class, subclass and protocol values. This driver will only support the net/QMI function while there are other drivers supporting other device functions. The net/QMI interface number may also differ from device to device. It has been noted that all the other interfaces have additional functional descriptors, so we use that to detect the interface supported by this driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:06 +00:00
{QMI_GOBI_DEVICE(0x05c6, 0x920b)}, /* Generic Gobi 2000 Modem device */
net: qmi_wwan: add several new Gobi devices Gobi devices are composite, needing both the qcserial and qmi_wwan drivers to support all functions. Re-syncing the list of supported devices with qcserial. Cc: Aleksander Morgado <aleksander@lanedo.com> Cc: Thomas Tuttle <ttuttle@chromium.org> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@tempietto.lan>
2012-09-01 03:47:26 +00:00
{QMI_GOBI_DEVICE(0x05c6, 0x920d)}, /* Gobi 3000 Composite */
net: qmi_wwan: add Gobi and Pantech UML290 device IDs Adding the Pantech UML290 and all non-QDL Gobi device IDs from the qcserial driver now that we have support for shared net/QMI USB interfaces. Most of these are not yet tested with this driver, but should be mostly identical to tested devices, except for device IDs. Gobi devices provide several different interfaces (serial/net/other) using the exact same class, subclass and protocol values. This driver will only support the net/QMI function while there are other drivers supporting other device functions. The net/QMI interface number may also differ from device to device. It has been noted that all the other interfaces have additional functional descriptors, so we use that to detect the interface supported by this driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:06 +00:00
{QMI_GOBI_DEVICE(0x05c6, 0x9225)}, /* Sony Gobi 2000 Modem device (N0279, VU730) */
{QMI_GOBI_DEVICE(0x05c6, 0x9245)}, /* Samsung Gobi 2000 Modem device (VL176) */
{QMI_GOBI_DEVICE(0x03f0, 0x251d)}, /* HP Gobi 2000 Modem device (VP412) */
{QMI_GOBI_DEVICE(0x05c6, 0x9215)}, /* Acer Gobi 2000 Modem device (VP413) */
{QMI_GOBI_DEVICE(0x05c6, 0x9265)}, /* Asus Gobi 2000 Modem device (VR305) */
{QMI_GOBI_DEVICE(0x05c6, 0x9235)}, /* Top Global Gobi 2000 Modem device (VR306) */
{QMI_GOBI_DEVICE(0x05c6, 0x9275)}, /* iRex Technologies Gobi 2000 Modem device (VR307) */
net: qmi_wwan: add Sierra Wireless devices Add 6 new devices and one modified device, based on information from laptop vendor Windows drivers. Sony provides a driver with two new devices using a Gobi 2k+ layout (1199:68a5 and 1199:68a9). The Sony driver also adds a non-standard QMI/net interface to the already supported 1199:9011 Gobi device. We do not know whether this is an alternate interface number or an additional interface which might be present, but that doesn't really matter. Lenovo provides a driver supporting 4 new devices: - MC7770 (1199:901b) with standard Gobi 2k+ layout - MC7700 (0f3d:68a2) with layout similar to MC7710 - MC7750 (114f:68a2) with layout similar to MC7710 - EM7700 (1199:901c) with layout similar to MC7710 Note regaring the three devices similar to MC7710: The Windows drivers only support interface #8 on these devices. The MC7710 can support QMI/net functions on interface #19 and #20 as well, and this driver is verified to work on interface #19 (a firmware bug is suspected to prevent #20 from working). We do not enable these additional interfaces until they either show up in a Windows driver or are verified to work in some other way. Therefore limiting the new devices to interface #8 for now. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:31 +00:00
{QMI_GOBI_DEVICE(0x1199, 0x68a5)}, /* Sierra Wireless Modem */
{QMI_GOBI_DEVICE(0x1199, 0x68a9)}, /* Sierra Wireless Modem */
net: qmi_wwan: add Gobi and Pantech UML290 device IDs Adding the Pantech UML290 and all non-QDL Gobi device IDs from the qcserial driver now that we have support for shared net/QMI USB interfaces. Most of these are not yet tested with this driver, but should be mostly identical to tested devices, except for device IDs. Gobi devices provide several different interfaces (serial/net/other) using the exact same class, subclass and protocol values. This driver will only support the net/QMI function while there are other drivers supporting other device functions. The net/QMI interface number may also differ from device to device. It has been noted that all the other interfaces have additional functional descriptors, so we use that to detect the interface supported by this driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:06 +00:00
{QMI_GOBI_DEVICE(0x1199, 0x9001)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
{QMI_GOBI_DEVICE(0x1199, 0x9002)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
{QMI_GOBI_DEVICE(0x1199, 0x9003)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
{QMI_GOBI_DEVICE(0x1199, 0x9004)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
{QMI_GOBI_DEVICE(0x1199, 0x9005)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
{QMI_GOBI_DEVICE(0x1199, 0x9006)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
{QMI_GOBI_DEVICE(0x1199, 0x9007)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
{QMI_GOBI_DEVICE(0x1199, 0x9008)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
{QMI_GOBI_DEVICE(0x1199, 0x9009)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
{QMI_GOBI_DEVICE(0x1199, 0x900a)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
{QMI_GOBI_DEVICE(0x1199, 0x9011)}, /* Sierra Wireless Gobi 2000 Modem device (MC8305) */
net: qmi_wwan: add Sierra Wireless devices Add 6 new devices and one modified device, based on information from laptop vendor Windows drivers. Sony provides a driver with two new devices using a Gobi 2k+ layout (1199:68a5 and 1199:68a9). The Sony driver also adds a non-standard QMI/net interface to the already supported 1199:9011 Gobi device. We do not know whether this is an alternate interface number or an additional interface which might be present, but that doesn't really matter. Lenovo provides a driver supporting 4 new devices: - MC7770 (1199:901b) with standard Gobi 2k+ layout - MC7700 (0f3d:68a2) with layout similar to MC7710 - MC7750 (114f:68a2) with layout similar to MC7710 - EM7700 (1199:901c) with layout similar to MC7710 Note regaring the three devices similar to MC7710: The Windows drivers only support interface #8 on these devices. The MC7710 can support QMI/net functions on interface #19 and #20 as well, and this driver is verified to work on interface #19 (a firmware bug is suspected to prevent #20 from working). We do not enable these additional interfaces until they either show up in a Windows driver or are verified to work in some other way. Therefore limiting the new devices to interface #8 for now. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:31 +00:00
{QMI_FIXED_INTF(0x1199, 0x9011, 5)}, /* alternate interface number!? */
net: qmi_wwan: add Gobi and Pantech UML290 device IDs Adding the Pantech UML290 and all non-QDL Gobi device IDs from the qcserial driver now that we have support for shared net/QMI USB interfaces. Most of these are not yet tested with this driver, but should be mostly identical to tested devices, except for device IDs. Gobi devices provide several different interfaces (serial/net/other) using the exact same class, subclass and protocol values. This driver will only support the net/QMI function while there are other drivers supporting other device functions. The net/QMI interface number may also differ from device to device. It has been noted that all the other interfaces have additional functional descriptors, so we use that to detect the interface supported by this driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:06 +00:00
{QMI_GOBI_DEVICE(0x16d8, 0x8002)}, /* CMDTech Gobi 2000 Modem device (VU922) */
{QMI_GOBI_DEVICE(0x05c6, 0x9205)}, /* Gobi 2000 Modem device */
{QMI_GOBI_DEVICE(0x1199, 0x9013)}, /* Sierra Wireless Gobi 3000 Modem device (MC8355) */
net: qmi_wwan: fix Gobi device probing for un2430 HP un2430 is a Gobi 3000 device. It was mistakenly treated as Gobi 1000 in patch b9f90eb2740203ff2592efe640409ad48335d1c2. I own this device and qmi_wwan works again with this fix. Signed-off-by: Pierre Sauter <pierre.sauter@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-10 07:02:59 +00:00
{QMI_GOBI_DEVICE(0x03f0, 0x371d)}, /* HP un2430 Mobile Broadband Module */
net: qmi_wwan: Add Sierra Wireless device IDs Some additional Gobi3K IDs found in the BSD/GPL licensed out-of-tree GobiNet driver from Sierra Wireless. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-23 23:19:32 +00:00
{QMI_GOBI_DEVICE(0x1199, 0x9015)}, /* Sierra Wireless Gobi 3000 Modem device */
{QMI_GOBI_DEVICE(0x1199, 0x9019)}, /* Sierra Wireless Gobi 3000 Modem device */
net: qmi_wwan: add Sierra Wireless devices Add 6 new devices and one modified device, based on information from laptop vendor Windows drivers. Sony provides a driver with two new devices using a Gobi 2k+ layout (1199:68a5 and 1199:68a9). The Sony driver also adds a non-standard QMI/net interface to the already supported 1199:9011 Gobi device. We do not know whether this is an alternate interface number or an additional interface which might be present, but that doesn't really matter. Lenovo provides a driver supporting 4 new devices: - MC7770 (1199:901b) with standard Gobi 2k+ layout - MC7700 (0f3d:68a2) with layout similar to MC7710 - MC7750 (114f:68a2) with layout similar to MC7710 - EM7700 (1199:901c) with layout similar to MC7710 Note regaring the three devices similar to MC7710: The Windows drivers only support interface #8 on these devices. The MC7710 can support QMI/net functions on interface #19 and #20 as well, and this driver is verified to work on interface #19 (a firmware bug is suspected to prevent #20 from working). We do not enable these additional interfaces until they either show up in a Windows driver or are verified to work in some other way. Therefore limiting the new devices to interface #8 for now. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:31 +00:00
{QMI_GOBI_DEVICE(0x1199, 0x901b)}, /* Sierra Wireless MC7770 */
net: qmi_wwan: add several new Gobi devices Gobi devices are composite, needing both the qcserial and qmi_wwan drivers to support all functions. Re-syncing the list of supported devices with qcserial. Cc: Aleksander Morgado <aleksander@lanedo.com> Cc: Thomas Tuttle <ttuttle@chromium.org> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@tempietto.lan>
2012-09-01 03:47:26 +00:00
{QMI_GOBI_DEVICE(0x12d1, 0x14f1)}, /* Sony Gobi 3000 Composite */
net: qmi_wwan: new device: Foxconn/Novatel E396 Foxconn-branded Novatel E396, Gobi3k modem. Cc: Dan Williams <dcbw@redhat.com> Cc: Bjørn Mork <bjorn@mork.no> Cc: Ben Chan <benchan@google.com> Signed-off-by: Aleksander Morgado <aleksander@lanedo.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-28 02:30:32 +00:00
{QMI_GOBI_DEVICE(0x1410, 0xa021)}, /* Foxconn Gobi 3000 Modem device (Novatel E396) */
net: qmi_wwan: add Sierra Wireless devices Add 6 new devices and one modified device, based on information from laptop vendor Windows drivers. Sony provides a driver with two new devices using a Gobi 2k+ layout (1199:68a5 and 1199:68a9). The Sony driver also adds a non-standard QMI/net interface to the already supported 1199:9011 Gobi device. We do not know whether this is an alternate interface number or an additional interface which might be present, but that doesn't really matter. Lenovo provides a driver supporting 4 new devices: - MC7770 (1199:901b) with standard Gobi 2k+ layout - MC7700 (0f3d:68a2) with layout similar to MC7710 - MC7750 (114f:68a2) with layout similar to MC7710 - EM7700 (1199:901c) with layout similar to MC7710 Note regaring the three devices similar to MC7710: The Windows drivers only support interface #8 on these devices. The MC7710 can support QMI/net functions on interface #19 and #20 as well, and this driver is verified to work on interface #19 (a firmware bug is suspected to prevent #20 from working). We do not enable these additional interfaces until they either show up in a Windows driver or are verified to work in some other way. Therefore limiting the new devices to interface #8 for now. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-12 09:16:31 +00:00
net: qmi_wwan: add Gobi and Pantech UML290 device IDs Adding the Pantech UML290 and all non-QDL Gobi device IDs from the qcserial driver now that we have support for shared net/QMI USB interfaces. Most of these are not yet tested with this driver, but should be mostly identical to tested devices, except for device IDs. Gobi devices provide several different interfaces (serial/net/other) using the exact same class, subclass and protocol values. This driver will only support the net/QMI function while there are other drivers supporting other device functions. The net/QMI interface number may also differ from device to device. It has been noted that all the other interfaces have additional functional descriptors, so we use that to detect the interface supported by this driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:06 +00:00
{ } /* END */
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
};
MODULE_DEVICE_TABLE(usb, products);
net: qmi_wwan: make dynamic device IDs work The usbnet API use the device ID table to store a pointer to a minidriver. Setting a generic pointer for dynamic device IDs will in most cases make them work as expected. usbnet will otherwise treat the dynamic IDs as blacklisted. That is rarely useful. There is no standard class describing devices supported by this driver, and most vendors don't even provide enough information to allow vendor specific wildcard matching. The result is that most of the supported devices must be explicitly listed in the device table. Allowing dynamic IDs to work both simplifies testing and verification of new devices, and provides a way for end users to use a device before the ID is added to the driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-17 11:14:32 +00:00
static int qmi_wwan_probe(struct usb_interface *intf, const struct usb_device_id *prod)
{
struct usb_device_id *id = (struct usb_device_id *)prod;
/* Workaround to enable dynamic IDs. This disables usbnet
* blacklisting functionality. Which, if required, can be
* reimplemented here by using a magic "blacklist" value
* instead of 0 in the static device id table
*/
if (!id->driver_info) {
dev_dbg(&intf->dev, "setting defaults for dynamic device id\n");
net: qmi_wwan: use a single bind function for all device types Refactoring the bind code lets us use a common driver_info struct for all supported devices, simplifying the code a bit. The real advantage is that devices using the CDC ECM interface layout now also can be added dynamically using the new_id sysfs interface. This simplifies testing of new devices. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-09-07 07:36:07 +00:00
id->driver_info = (unsigned long)&qmi_wwan_info;
net: qmi_wwan: make dynamic device IDs work The usbnet API use the device ID table to store a pointer to a minidriver. Setting a generic pointer for dynamic device IDs will in most cases make them work as expected. usbnet will otherwise treat the dynamic IDs as blacklisted. That is rarely useful. There is no standard class describing devices supported by this driver, and most vendors don't even provide enough information to allow vendor specific wildcard matching. The result is that most of the supported devices must be explicitly listed in the device table. Allowing dynamic IDs to work both simplifies testing and verification of new devices, and provides a way for end users to use a device before the ID is added to the driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-17 11:14:32 +00:00
}
return usbnet_probe(intf, id);
}
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
static struct usb_driver qmi_wwan_driver = {
.name = "qmi_wwan",
.id_table = products,
net: qmi_wwan: make dynamic device IDs work The usbnet API use the device ID table to store a pointer to a minidriver. Setting a generic pointer for dynamic device IDs will in most cases make them work as expected. usbnet will otherwise treat the dynamic IDs as blacklisted. That is rarely useful. There is no standard class describing devices supported by this driver, and most vendors don't even provide enough information to allow vendor specific wildcard matching. The result is that most of the supported devices must be explicitly listed in the device table. Allowing dynamic IDs to work both simplifies testing and verification of new devices, and provides a way for end users to use a device before the ID is added to the driver. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-17 11:14:32 +00:00
.probe = qmi_wwan_probe,
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
.disconnect = usbnet_disconnect,
net: qmi_wwan: support devices having a shared QMI/wwan interface Use the new cdc-wdm subdriver interface to create a device management device even for USB devices having a single combined QMI/wwan USB interface with three endpoints (int, bulk in, bulk out) instead of separate data and control interfaces. Some Huawei devices can be switched to a single interface mode for use with other operating systems than Linux. This adds support for these devices when they run in such non-Linux modes. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-03-09 11:35:05 +00:00
.suspend = qmi_wwan_suspend,
.resume = qmi_wwan_resume,
.reset_resume = qmi_wwan_resume,
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
.supports_autosuspend = 1,
USB: Disable hub-initiated LPM for comms devices. Hub-initiated LPM is not good for USB communications devices. Comms devices should be able to tell when their link can go into a lower power state, because they know when an incoming transmission is finished. Ideally, these devices would slam their links into a lower power state, using the device-initiated LPM, after finishing the last packet of their data transfer. If we enable the idle timeouts for the parent hubs to enable hub-initiated LPM, we will get a lot of useless LPM packets on the bus as the devices reject LPM transitions when they're in the middle of receiving data. Worse, some devices might blindly accept the hub-initiated LPM and power down their radios while they're in the middle of receiving a transmission. The Intel Windows folks are disabling hub-initiated LPM for all USB communications devices under a xHCI USB 3.0 host. In order to keep the Linux behavior as close as possible to Windows, we need to do the same in Linux. Set the disable_hub_initiated_lpm flag for for all USB communications drivers. I know there aren't currently any USB 3.0 devices that implement these class specifications, but we should be ready if they do. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Hansjoerg Lipp <hjlipp@web.de> Cc: Tilman Schmidt <tilman@imap.cc> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Jan Dumon <j.dumon@option.com> Cc: Petko Manolov <petkan@users.sourceforge.net> Cc: Steve Glendinning <steve.glendinning@smsc.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com> Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Brett Rudley <brudley@broadcom.com> Cc: Roland Vossen <rvossen@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com> Cc: Kan Yan <kanyan@broadcom.com> Cc: Dan Williams <dcbw@redhat.com> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: Herton Ronaldo Krzesinski <herton@canonical.com> Cc: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Cc: Daniel Drake <dsd@gentoo.org> Cc: Ulrich Kunitz <kune@deine-taler.de> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-04-23 17:08:51 +00:00
.disable_hub_initiated_lpm = 1,
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
};
net: qmi_wwan: use module_usb_driver macro Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-19 00:42:03 +00:00
module_usb_driver(qmi_wwan_driver);
net: usb: qmi_wwan: New driver for Huawei QMI based WWAN devices Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-01-19 15:37:22 +00:00
MODULE_AUTHOR("Bjørn Mork <bjorn@mork.no>");
MODULE_DESCRIPTION("Qualcomm MSM Interface (QMI) WWAN driver");
MODULE_LICENSE("GPL");
Reference in New Issue Copy Permalink