forked from Minki/linux
53 lines
1.4 KiB
Plaintext
53 lines
1.4 KiB
Plaintext
|
NXP LPC32xx SoC NAND SLC controller
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: "nxp,lpc3220-slc"
|
||
|
|
- reg: Address and size of the controller
|
||
|
|
- nand-on-flash-bbt: Use bad block table on flash
|
||
|
|
- gpios: GPIO specification for NAND write protect
|
||
|
|
|
||
|
|
The following required properties are very controller specific. See the LPC32xx
|
||
|
|
User Manual:
|
||
|
|
- nxp,wdr-clks: Delay before Ready signal is tested on write (W_RDY)
|
||
|
|
- nxp,rdr-clks: Delay before Ready signal is tested on read (R_RDY)
|
||
|
|
(The following values are specified in Hz, to make them independent of actual
|
||
|
|
clock speed:)
|
||
|
|
- nxp,wwidth: Write pulse width (W_WIDTH)
|
||
|
|
- nxp,whold: Write hold time (W_HOLD)
|
||
|
|
- nxp,wsetup: Write setup time (W_SETUP)
|
||
|
|
- nxp,rwidth: Read pulse width (R_WIDTH)
|
||
|
|
- nxp,rhold: Read hold time (R_HOLD)
|
||
|
|
- nxp,rsetup: Read setup time (R_SETUP)
|
||
|
|
|
||
|
|
Optional subnodes:
|
||
|
|
- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
|
||
|
|
|
||
|
|
Example:
|
||
|
|
|
||
|
|
slc: flash@20020000 {
|
||
|
|
compatible = "nxp,lpc3220-slc";
|
||
|
|
reg = <0x20020000 0x1000>;
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <1>;
|
||
|
|
|
||
|
|
nxp,wdr-clks = <14>;
|
||
|
|
nxp,wwidth = <40000000>;
|
||
|
|
nxp,whold = <100000000>;
|
||
|
|
nxp,wsetup = <100000000>;
|
||
|
|
nxp,rdr-clks = <14>;
|
||
|
|
nxp,rwidth = <40000000>;
|
||
|
|
nxp,rhold = <66666666>;
|
||
|
|
nxp,rsetup = <100000000>;
|
||
|
|
nand-on-flash-bbt;
|
||
|
|
gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
|
||
|
|
|
||
|
|
mtd0@00000000 {
|
||
|
|
label = "phy3250-boot";
|
||
|
|
reg = <0x00000000 0x00064000>;
|
||
|
|
read-only;
|
||
|
|
};
|
||
|
|
|
||
|
|
...
|
||
|
|
|
||
|
|
};
|