linux/drivers/dma/dw_dmac.c

1728 lines
44 KiB
C
Raw Normal View History

dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/*
* Driver for the Synopsys DesignWare DMA Controller (aka DMACA on
* AVR32 systems.)
*
* Copyright (C) 2007-2008 Atmel Corporation
* Copyright (C) 2010-2011 ST Microelectronics
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/bitops.h>
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/of.h>
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include "dw_dmac_regs.h"
#include "dmaengine.h"
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/*
* This supports the Synopsys "DesignWare AHB Central DMA Controller",
* (DW_ahb_dmac) which is used with various AMBA 2.0 systems (not all
* of which use ARM any more). See the "Databook" from Synopsys for
* information beyond what licensees probably provide.
*
* The driver has currently been tested only with the Atmel AT32AP7000,
* which does not support descriptor writeback.
*/
static inline unsigned int dwc_get_dms(struct dw_dma_slave *slave)
{
return slave ? slave->dst_master : 0;
}
static inline unsigned int dwc_get_sms(struct dw_dma_slave *slave)
{
return slave ? slave->src_master : 1;
}
#define DWC_DEFAULT_CTLLO(_chan) ({ \
struct dw_dma_slave *__slave = (_chan->private); \
struct dw_dma_chan *_dwc = to_dw_dma_chan(_chan); \
struct dma_slave_config *_sconfig = &_dwc->dma_sconfig; \
int _dms = dwc_get_dms(__slave); \
int _sms = dwc_get_sms(__slave); \
u8 _smsize = __slave ? _sconfig->src_maxburst : \
DW_DMA_MSIZE_16; \
u8 _dmsize = __slave ? _sconfig->dst_maxburst : \
DW_DMA_MSIZE_16; \
\
(DWC_CTLL_DST_MSIZE(_dmsize) \
| DWC_CTLL_SRC_MSIZE(_smsize) \
| DWC_CTLL_LLP_D_EN \
| DWC_CTLL_LLP_S_EN \
| DWC_CTLL_DMS(_dms) \
| DWC_CTLL_SMS(_sms)); \
})
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/*
* Number of descriptors to allocate for each channel. This should be
* made configurable somehow; preferably, the clients (at least the
* ones using slave transfers) should be able to give us a hint.
*/
#define NR_DESCS_PER_CHANNEL 64
/*----------------------------------------------------------------------*/
/*
* Because we're not relying on writeback from the controller (it may not
* even be configured into the core!) we don't need to use dma_pool. These
* descriptors -- and associated data -- are cacheable. We do need to make
* sure their dcache entries are written back before handing them off to
* the controller, though.
*/
static struct device *chan2dev(struct dma_chan *chan)
{
return &chan->dev->device;
}
static struct device *chan2parent(struct dma_chan *chan)
{
return chan->dev->device.parent;
}
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
static struct dw_desc *dwc_first_active(struct dw_dma_chan *dwc)
{
return list_entry(dwc->active_list.next, struct dw_desc, desc_node);
}
static struct dw_desc *dwc_desc_get(struct dw_dma_chan *dwc)
{
struct dw_desc *desc, *_desc;
struct dw_desc *ret = NULL;
unsigned int i = 0;
unsigned long flags;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
spin_lock_irqsave(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
list_for_each_entry_safe(desc, _desc, &dwc->free_list, desc_node) {
i++;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (async_tx_test_ack(&desc->txd)) {
list_del(&desc->desc_node);
ret = desc;
break;
}
dev_dbg(chan2dev(&dwc->chan), "desc %p not ACKed\n", desc);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dev_vdbg(chan2dev(&dwc->chan), "scanned %u descriptors on freelist\n", i);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
return ret;
}
static void dwc_sync_desc_for_cpu(struct dw_dma_chan *dwc, struct dw_desc *desc)
{
struct dw_desc *child;
list_for_each_entry(child, &desc->tx_list, desc_node)
dma_sync_single_for_cpu(chan2parent(&dwc->chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
child->txd.phys, sizeof(child->lli),
DMA_TO_DEVICE);
dma_sync_single_for_cpu(chan2parent(&dwc->chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
desc->txd.phys, sizeof(desc->lli),
DMA_TO_DEVICE);
}
/*
* Move a descriptor, including any children, to the free list.
* `desc' must not be on any lists.
*/
static void dwc_desc_put(struct dw_dma_chan *dwc, struct dw_desc *desc)
{
unsigned long flags;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (desc) {
struct dw_desc *child;
dwc_sync_desc_for_cpu(dwc, desc);
spin_lock_irqsave(&dwc->lock, flags);
list_for_each_entry(child, &desc->tx_list, desc_node)
dev_vdbg(chan2dev(&dwc->chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
"moving child desc %p to freelist\n",
child);
list_splice_init(&desc->tx_list, &dwc->free_list);
dev_vdbg(chan2dev(&dwc->chan), "moving desc %p to freelist\n", desc);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
list_add(&desc->desc_node, &dwc->free_list);
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
}
static void dwc_initialize(struct dw_dma_chan *dwc)
{
struct dw_dma *dw = to_dw_dma(dwc->chan.device);
struct dw_dma_slave *dws = dwc->chan.private;
u32 cfghi = DWC_CFGH_FIFO_MODE;
u32 cfglo = DWC_CFGL_CH_PRIOR(dwc->priority);
if (dwc->initialized == true)
return;
if (dws) {
/*
* We need controller-specific data to set up slave
* transfers.
*/
BUG_ON(!dws->dma_dev || dws->dma_dev != dw->dma.dev);
cfghi = dws->cfg_hi;
cfglo |= dws->cfg_lo & ~DWC_CFGL_CH_PRIOR_MASK;
} else {
if (dwc->dma_sconfig.direction == DMA_MEM_TO_DEV)
cfghi = DWC_CFGH_DST_PER(dwc->dma_sconfig.slave_id);
else if (dwc->dma_sconfig.direction == DMA_DEV_TO_MEM)
cfghi = DWC_CFGH_SRC_PER(dwc->dma_sconfig.slave_id);
}
channel_writel(dwc, CFG_LO, cfglo);
channel_writel(dwc, CFG_HI, cfghi);
/* Enable interrupts */
channel_set_bit(dw, MASK.XFER, dwc->mask);
channel_set_bit(dw, MASK.ERROR, dwc->mask);
dwc->initialized = true;
}
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/*----------------------------------------------------------------------*/
static inline unsigned int dwc_fast_fls(unsigned long long v)
{
/*
* We can be a lot more clever here, but this should take care
* of the most common optimization.
*/
if (!(v & 7))
return 3;
else if (!(v & 3))
return 2;
else if (!(v & 1))
return 1;
return 0;
}
static inline void dwc_dump_chan_regs(struct dw_dma_chan *dwc)
{
dev_err(chan2dev(&dwc->chan),
" SAR: 0x%x DAR: 0x%x LLP: 0x%x CTL: 0x%x:%08x\n",
channel_readl(dwc, SAR),
channel_readl(dwc, DAR),
channel_readl(dwc, LLP),
channel_readl(dwc, CTL_HI),
channel_readl(dwc, CTL_LO));
}
static inline void dwc_chan_disable(struct dw_dma *dw, struct dw_dma_chan *dwc)
{
channel_clear_bit(dw, CH_EN, dwc->mask);
while (dma_readl(dw, CH_EN) & dwc->mask)
cpu_relax();
}
/*----------------------------------------------------------------------*/
/* Perform single block transfer */
static inline void dwc_do_single_block(struct dw_dma_chan *dwc,
struct dw_desc *desc)
{
struct dw_dma *dw = to_dw_dma(dwc->chan.device);
u32 ctllo;
/* Software emulation of LLP mode relies on interrupts to continue
* multi block transfer. */
ctllo = desc->lli.ctllo | DWC_CTLL_INT_EN;
channel_writel(dwc, SAR, desc->lli.sar);
channel_writel(dwc, DAR, desc->lli.dar);
channel_writel(dwc, CTL_LO, ctllo);
channel_writel(dwc, CTL_HI, desc->lli.ctlhi);
channel_set_bit(dw, CH_EN, dwc->mask);
}
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/* Called with dwc->lock held and bh disabled */
static void dwc_dostart(struct dw_dma_chan *dwc, struct dw_desc *first)
{
struct dw_dma *dw = to_dw_dma(dwc->chan.device);
unsigned long was_soft_llp;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/* ASSERT: channel is idle */
if (dma_readl(dw, CH_EN) & dwc->mask) {
dev_err(chan2dev(&dwc->chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
"BUG: Attempted to start non-idle channel\n");
dwc_dump_chan_regs(dwc);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/* The tasklet will hopefully advance the queue... */
return;
}
if (dwc->nollp) {
was_soft_llp = test_and_set_bit(DW_DMA_IS_SOFT_LLP,
&dwc->flags);
if (was_soft_llp) {
dev_err(chan2dev(&dwc->chan),
"BUG: Attempted to start new LLP transfer "
"inside ongoing one\n");
return;
}
dwc_initialize(dwc);
dwc->tx_list = &first->tx_list;
dwc->tx_node_active = first->tx_list.next;
dwc_do_single_block(dwc, first);
return;
}
dwc_initialize(dwc);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
channel_writel(dwc, LLP, first->txd.phys);
channel_writel(dwc, CTL_LO,
DWC_CTLL_LLP_D_EN | DWC_CTLL_LLP_S_EN);
channel_writel(dwc, CTL_HI, 0);
channel_set_bit(dw, CH_EN, dwc->mask);
}
/*----------------------------------------------------------------------*/
static void
dwc_descriptor_complete(struct dw_dma_chan *dwc, struct dw_desc *desc,
bool callback_required)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
{
dma_async_tx_callback callback = NULL;
void *param = NULL;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
struct dma_async_tx_descriptor *txd = &desc->txd;
struct dw_desc *child;
unsigned long flags;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dev_vdbg(chan2dev(&dwc->chan), "descriptor %u complete\n", txd->cookie);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
spin_lock_irqsave(&dwc->lock, flags);
dma_cookie_complete(txd);
if (callback_required) {
callback = txd->callback;
param = txd->callback_param;
}
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dwc_sync_desc_for_cpu(dwc, desc);
/* async_tx_ack */
list_for_each_entry(child, &desc->tx_list, desc_node)
async_tx_ack(&child->txd);
async_tx_ack(&desc->txd);
list_splice_init(&desc->tx_list, &dwc->free_list);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
list_move(&desc->desc_node, &dwc->free_list);
if (!dwc->chan.private) {
struct device *parent = chan2parent(&dwc->chan);
if (!(txd->flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
if (txd->flags & DMA_COMPL_DEST_UNMAP_SINGLE)
dma_unmap_single(parent, desc->lli.dar,
desc->len, DMA_FROM_DEVICE);
else
dma_unmap_page(parent, desc->lli.dar,
desc->len, DMA_FROM_DEVICE);
}
if (!(txd->flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
if (txd->flags & DMA_COMPL_SRC_UNMAP_SINGLE)
dma_unmap_single(parent, desc->lli.sar,
desc->len, DMA_TO_DEVICE);
else
dma_unmap_page(parent, desc->lli.sar,
desc->len, DMA_TO_DEVICE);
}
}
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
spin_unlock_irqrestore(&dwc->lock, flags);
if (callback_required && callback)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
callback(param);
}
static void dwc_complete_all(struct dw_dma *dw, struct dw_dma_chan *dwc)
{
struct dw_desc *desc, *_desc;
LIST_HEAD(list);
unsigned long flags;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
spin_lock_irqsave(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (dma_readl(dw, CH_EN) & dwc->mask) {
dev_err(chan2dev(&dwc->chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
"BUG: XFER bit set, but channel not idle!\n");
/* Try to continue after resetting the channel... */
dwc_chan_disable(dw, dwc);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
/*
* Submit queued descriptors ASAP, i.e. before we go through
* the completed ones.
*/
list_splice_init(&dwc->active_list, &list);
if (!list_empty(&dwc->queue)) {
list_move(dwc->queue.next, &dwc->active_list);
dwc_dostart(dwc, dwc_first_active(dwc));
}
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
list_for_each_entry_safe(desc, _desc, &list, desc_node)
dwc_descriptor_complete(dwc, desc, true);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
static void dwc_scan_descriptors(struct dw_dma *dw, struct dw_dma_chan *dwc)
{
dma_addr_t llp;
struct dw_desc *desc, *_desc;
struct dw_desc *child;
u32 status_xfer;
unsigned long flags;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
spin_lock_irqsave(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
llp = channel_readl(dwc, LLP);
status_xfer = dma_readl(dw, RAW.XFER);
if (status_xfer & dwc->mask) {
/* Everything we've submitted is done */
dma_writel(dw, CLEAR.XFER, dwc->mask);
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dwc_complete_all(dw, dwc);
return;
}
if (list_empty(&dwc->active_list)) {
spin_unlock_irqrestore(&dwc->lock, flags);
return;
}
dev_vdbg(chan2dev(&dwc->chan), "%s: llp=0x%llx\n", __func__,
(unsigned long long)llp);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
list_for_each_entry_safe(desc, _desc, &dwc->active_list, desc_node) {
/* check first descriptors addr */
if (desc->txd.phys == llp) {
spin_unlock_irqrestore(&dwc->lock, flags);
return;
}
/* check first descriptors llp */
if (desc->lli.llp == llp) {
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/* This one is currently in progress */
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
return;
}
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
list_for_each_entry(child, &desc->tx_list, desc_node)
if (child->lli.llp == llp) {
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/* Currently in progress */
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
return;
}
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/*
* No descriptors so far seem to be in progress, i.e.
* this one must be done.
*/
spin_unlock_irqrestore(&dwc->lock, flags);
dwc_descriptor_complete(dwc, desc, true);
spin_lock_irqsave(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
dev_err(chan2dev(&dwc->chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
"BUG: All descriptors done, but channel not idle!\n");
/* Try to continue after resetting the channel... */
dwc_chan_disable(dw, dwc);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (!list_empty(&dwc->queue)) {
list_move(dwc->queue.next, &dwc->active_list);
dwc_dostart(dwc, dwc_first_active(dwc));
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
static inline void dwc_dump_lli(struct dw_dma_chan *dwc, struct dw_lli *lli)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
{
dev_printk(KERN_CRIT, chan2dev(&dwc->chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
" desc: s0x%x d0x%x l0x%x c0x%x:%x\n",
lli->sar, lli->dar, lli->llp, lli->ctlhi, lli->ctllo);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
static void dwc_handle_error(struct dw_dma *dw, struct dw_dma_chan *dwc)
{
struct dw_desc *bad_desc;
struct dw_desc *child;
unsigned long flags;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dwc_scan_descriptors(dw, dwc);
spin_lock_irqsave(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/*
* The descriptor currently at the head of the active list is
* borked. Since we don't have any way to report errors, we'll
* just have to scream loudly and try to carry on.
*/
bad_desc = dwc_first_active(dwc);
list_del_init(&bad_desc->desc_node);
list_move(dwc->queue.next, dwc->active_list.prev);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/* Clear the error flag and try to restart the controller */
dma_writel(dw, CLEAR.ERROR, dwc->mask);
if (!list_empty(&dwc->active_list))
dwc_dostart(dwc, dwc_first_active(dwc));
/*
* KERN_CRITICAL may seem harsh, but since this only happens
* when someone submits a bad physical address in a
* descriptor, we should consider ourselves lucky that the
* controller flagged an error instead of scribbling over
* random memory locations.
*/
dev_printk(KERN_CRIT, chan2dev(&dwc->chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
"Bad descriptor submitted for DMA!\n");
dev_printk(KERN_CRIT, chan2dev(&dwc->chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
" cookie: %d\n", bad_desc->txd.cookie);
dwc_dump_lli(dwc, &bad_desc->lli);
list_for_each_entry(child, &bad_desc->tx_list, desc_node)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dwc_dump_lli(dwc, &child->lli);
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/* Pretend the descriptor completed successfully */
dwc_descriptor_complete(dwc, bad_desc, true);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
/* --------------------- Cyclic DMA API extensions -------------------- */
inline dma_addr_t dw_dma_get_src_addr(struct dma_chan *chan)
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
return channel_readl(dwc, SAR);
}
EXPORT_SYMBOL(dw_dma_get_src_addr);
inline dma_addr_t dw_dma_get_dst_addr(struct dma_chan *chan)
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
return channel_readl(dwc, DAR);
}
EXPORT_SYMBOL(dw_dma_get_dst_addr);
/* called with dwc->lock held and all DMAC interrupts disabled */
static void dwc_handle_cyclic(struct dw_dma *dw, struct dw_dma_chan *dwc,
u32 status_err, u32 status_xfer)
{
unsigned long flags;
if (dwc->mask) {
void (*callback)(void *param);
void *callback_param;
dev_vdbg(chan2dev(&dwc->chan), "new cyclic period llp 0x%08x\n",
channel_readl(dwc, LLP));
callback = dwc->cdesc->period_callback;
callback_param = dwc->cdesc->period_callback_param;
if (callback)
callback(callback_param);
}
/*
* Error and transfer complete are highly unlikely, and will most
* likely be due to a configuration error by the user.
*/
if (unlikely(status_err & dwc->mask) ||
unlikely(status_xfer & dwc->mask)) {
int i;
dev_err(chan2dev(&dwc->chan), "cyclic DMA unexpected %s "
"interrupt, stopping DMA transfer\n",
status_xfer ? "xfer" : "error");
spin_lock_irqsave(&dwc->lock, flags);
dwc_dump_chan_regs(dwc);
dwc_chan_disable(dw, dwc);
/* make sure DMA does not restart by loading a new list */
channel_writel(dwc, LLP, 0);
channel_writel(dwc, CTL_LO, 0);
channel_writel(dwc, CTL_HI, 0);
dma_writel(dw, CLEAR.ERROR, dwc->mask);
dma_writel(dw, CLEAR.XFER, dwc->mask);
for (i = 0; i < dwc->cdesc->periods; i++)
dwc_dump_lli(dwc, &dwc->cdesc->desc[i]->lli);
spin_unlock_irqrestore(&dwc->lock, flags);
}
}
/* ------------------------------------------------------------------------- */
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
static void dw_dma_tasklet(unsigned long data)
{
struct dw_dma *dw = (struct dw_dma *)data;
struct dw_dma_chan *dwc;
u32 status_xfer;
u32 status_err;
int i;
status_xfer = dma_readl(dw, RAW.XFER);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
status_err = dma_readl(dw, RAW.ERROR);
dev_vdbg(dw->dma.dev, "%s: status_err=%x\n", __func__, status_err);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
for (i = 0; i < dw->dma.chancnt; i++) {
dwc = &dw->chan[i];
if (test_bit(DW_DMA_IS_CYCLIC, &dwc->flags))
dwc_handle_cyclic(dw, dwc, status_err, status_xfer);
else if (status_err & (1 << i))
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dwc_handle_error(dw, dwc);
else if (status_xfer & (1 << i)) {
unsigned long flags;
spin_lock_irqsave(&dwc->lock, flags);
if (test_bit(DW_DMA_IS_SOFT_LLP, &dwc->flags)) {
if (dwc->tx_node_active != dwc->tx_list) {
struct dw_desc *desc =
list_entry(dwc->tx_node_active,
struct dw_desc,
desc_node);
dma_writel(dw, CLEAR.XFER, dwc->mask);
/* move pointer to next descriptor */
dwc->tx_node_active =
dwc->tx_node_active->next;
dwc_do_single_block(dwc, desc);
spin_unlock_irqrestore(&dwc->lock, flags);
continue;
} else {
/* we are done here */
clear_bit(DW_DMA_IS_SOFT_LLP, &dwc->flags);
}
}
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dwc_scan_descriptors(dw, dwc);
}
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
/*
* Re-enable interrupts.
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
*/
channel_set_bit(dw, MASK.XFER, dw->all_chan_mask);
channel_set_bit(dw, MASK.ERROR, dw->all_chan_mask);
}
static irqreturn_t dw_dma_interrupt(int irq, void *dev_id)
{
struct dw_dma *dw = dev_id;
u32 status;
dev_vdbg(dw->dma.dev, "%s: status=0x%x\n", __func__,
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dma_readl(dw, STATUS_INT));
/*
* Just disable the interrupts. We'll turn them back on in the
* softirq handler.
*/
channel_clear_bit(dw, MASK.XFER, dw->all_chan_mask);
channel_clear_bit(dw, MASK.ERROR, dw->all_chan_mask);
status = dma_readl(dw, STATUS_INT);
if (status) {
dev_err(dw->dma.dev,
"BUG: Unexpected interrupts pending: 0x%x\n",
status);
/* Try to recover */
channel_clear_bit(dw, MASK.XFER, (1 << 8) - 1);
channel_clear_bit(dw, MASK.SRC_TRAN, (1 << 8) - 1);
channel_clear_bit(dw, MASK.DST_TRAN, (1 << 8) - 1);
channel_clear_bit(dw, MASK.ERROR, (1 << 8) - 1);
}
tasklet_schedule(&dw->tasklet);
return IRQ_HANDLED;
}
/*----------------------------------------------------------------------*/
static dma_cookie_t dwc_tx_submit(struct dma_async_tx_descriptor *tx)
{
struct dw_desc *desc = txd_to_dw_desc(tx);
struct dw_dma_chan *dwc = to_dw_dma_chan(tx->chan);
dma_cookie_t cookie;
unsigned long flags;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
spin_lock_irqsave(&dwc->lock, flags);
cookie = dma_cookie_assign(tx);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/*
* REVISIT: We should attempt to chain as many descriptors as
* possible, perhaps even appending to those already submitted
* for DMA. But this is hard to do in a race-free manner.
*/
if (list_empty(&dwc->active_list)) {
dev_vdbg(chan2dev(tx->chan), "%s: started %u\n", __func__,
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
desc->txd.cookie);
list_add_tail(&desc->desc_node, &dwc->active_list);
dwc_dostart(dwc, dwc_first_active(dwc));
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
} else {
dev_vdbg(chan2dev(tx->chan), "%s: queued %u\n", __func__,
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
desc->txd.cookie);
list_add_tail(&desc->desc_node, &dwc->queue);
}
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
return cookie;
}
static struct dma_async_tx_descriptor *
dwc_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src,
size_t len, unsigned long flags)
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
struct dw_dma_slave *dws = chan->private;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
struct dw_desc *desc;
struct dw_desc *first;
struct dw_desc *prev;
size_t xfer_count;
size_t offset;
unsigned int src_width;
unsigned int dst_width;
unsigned int data_width;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
u32 ctllo;
dev_vdbg(chan2dev(chan),
"%s: d0x%llx s0x%llx l0x%zx f0x%lx\n", __func__,
(unsigned long long)dest, (unsigned long long)src,
len, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (unlikely(!len)) {
dev_dbg(chan2dev(chan), "%s: length is zero!\n", __func__);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
return NULL;
}
data_width = min_t(unsigned int, dwc->dw->data_width[dwc_get_sms(dws)],
dwc->dw->data_width[dwc_get_dms(dws)]);
src_width = dst_width = min_t(unsigned int, data_width,
dwc_fast_fls(src | dest | len));
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
ctllo = DWC_DEFAULT_CTLLO(chan)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
| DWC_CTLL_DST_WIDTH(dst_width)
| DWC_CTLL_SRC_WIDTH(src_width)
| DWC_CTLL_DST_INC
| DWC_CTLL_SRC_INC
| DWC_CTLL_FC_M2M;
prev = first = NULL;
for (offset = 0; offset < len; offset += xfer_count << src_width) {
xfer_count = min_t(size_t, (len - offset) >> src_width,
dwc->block_size);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
desc = dwc_desc_get(dwc);
if (!desc)
goto err_desc_get;
desc->lli.sar = src + offset;
desc->lli.dar = dest + offset;
desc->lli.ctllo = ctllo;
desc->lli.ctlhi = xfer_count;
if (!first) {
first = desc;
} else {
prev->lli.llp = desc->txd.phys;
dma_sync_single_for_device(chan2parent(chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
prev->txd.phys, sizeof(prev->lli),
DMA_TO_DEVICE);
list_add_tail(&desc->desc_node,
&first->tx_list);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
prev = desc;
}
if (flags & DMA_PREP_INTERRUPT)
/* Trigger interrupt after last block */
prev->lli.ctllo |= DWC_CTLL_INT_EN;
prev->lli.llp = 0;
dma_sync_single_for_device(chan2parent(chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
prev->txd.phys, sizeof(prev->lli),
DMA_TO_DEVICE);
first->txd.flags = flags;
first->len = len;
return &first->txd;
err_desc_get:
dwc_desc_put(dwc, first);
return NULL;
}
static struct dma_async_tx_descriptor *
dwc_prep_slave_sg(struct dma_chan *chan, struct scatterlist *sgl,
unsigned int sg_len, enum dma_transfer_direction direction,
unsigned long flags, void *context)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
struct dw_dma_slave *dws = chan->private;
struct dma_slave_config *sconfig = &dwc->dma_sconfig;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
struct dw_desc *prev;
struct dw_desc *first;
u32 ctllo;
dma_addr_t reg;
unsigned int reg_width;
unsigned int mem_width;
unsigned int data_width;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
unsigned int i;
struct scatterlist *sg;
size_t total_len = 0;
dev_vdbg(chan2dev(chan), "%s\n", __func__);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (unlikely(!dws || !sg_len))
return NULL;
prev = first = NULL;
switch (direction) {
case DMA_MEM_TO_DEV:
reg_width = __fls(sconfig->dst_addr_width);
reg = sconfig->dst_addr;
ctllo = (DWC_DEFAULT_CTLLO(chan)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
| DWC_CTLL_DST_WIDTH(reg_width)
| DWC_CTLL_DST_FIX
| DWC_CTLL_SRC_INC);
ctllo |= sconfig->device_fc ? DWC_CTLL_FC(DW_DMA_FC_P_M2P) :
DWC_CTLL_FC(DW_DMA_FC_D_M2P);
data_width = dwc->dw->data_width[dwc_get_sms(dws)];
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
for_each_sg(sgl, sg, sg_len, i) {
struct dw_desc *desc;
u32 len, dlen, mem;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
mem = sg_dma_address(sg);
len = sg_dma_len(sg);
mem_width = min_t(unsigned int,
data_width, dwc_fast_fls(mem | len));
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
slave_sg_todev_fill_desc:
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
desc = dwc_desc_get(dwc);
if (!desc) {
dev_err(chan2dev(chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
"not enough descriptors available\n");
goto err_desc_get;
}
desc->lli.sar = mem;
desc->lli.dar = reg;
desc->lli.ctllo = ctllo | DWC_CTLL_SRC_WIDTH(mem_width);
if ((len >> mem_width) > dwc->block_size) {
dlen = dwc->block_size << mem_width;
mem += dlen;
len -= dlen;
} else {
dlen = len;
len = 0;
}
desc->lli.ctlhi = dlen >> mem_width;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (!first) {
first = desc;
} else {
prev->lli.llp = desc->txd.phys;
dma_sync_single_for_device(chan2parent(chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
prev->txd.phys,
sizeof(prev->lli),
DMA_TO_DEVICE);
list_add_tail(&desc->desc_node,
&first->tx_list);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
prev = desc;
total_len += dlen;
if (len)
goto slave_sg_todev_fill_desc;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
break;
case DMA_DEV_TO_MEM:
reg_width = __fls(sconfig->src_addr_width);
reg = sconfig->src_addr;
ctllo = (DWC_DEFAULT_CTLLO(chan)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
| DWC_CTLL_SRC_WIDTH(reg_width)
| DWC_CTLL_DST_INC
| DWC_CTLL_SRC_FIX);
ctllo |= sconfig->device_fc ? DWC_CTLL_FC(DW_DMA_FC_P_P2M) :
DWC_CTLL_FC(DW_DMA_FC_D_P2M);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
data_width = dwc->dw->data_width[dwc_get_dms(dws)];
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
for_each_sg(sgl, sg, sg_len, i) {
struct dw_desc *desc;
u32 len, dlen, mem;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
mem = sg_dma_address(sg);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
len = sg_dma_len(sg);
mem_width = min_t(unsigned int,
data_width, dwc_fast_fls(mem | len));
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
slave_sg_fromdev_fill_desc:
desc = dwc_desc_get(dwc);
if (!desc) {
dev_err(chan2dev(chan),
"not enough descriptors available\n");
goto err_desc_get;
}
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
desc->lli.sar = reg;
desc->lli.dar = mem;
desc->lli.ctllo = ctllo | DWC_CTLL_DST_WIDTH(mem_width);
if ((len >> reg_width) > dwc->block_size) {
dlen = dwc->block_size << reg_width;
mem += dlen;
len -= dlen;
} else {
dlen = len;
len = 0;
}
desc->lli.ctlhi = dlen >> reg_width;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (!first) {
first = desc;
} else {
prev->lli.llp = desc->txd.phys;
dma_sync_single_for_device(chan2parent(chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
prev->txd.phys,
sizeof(prev->lli),
DMA_TO_DEVICE);
list_add_tail(&desc->desc_node,
&first->tx_list);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
prev = desc;
total_len += dlen;
if (len)
goto slave_sg_fromdev_fill_desc;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
break;
default:
return NULL;
}
if (flags & DMA_PREP_INTERRUPT)
/* Trigger interrupt after last block */
prev->lli.ctllo |= DWC_CTLL_INT_EN;
prev->lli.llp = 0;
dma_sync_single_for_device(chan2parent(chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
prev->txd.phys, sizeof(prev->lli),
DMA_TO_DEVICE);
first->len = total_len;
return &first->txd;
err_desc_get:
dwc_desc_put(dwc, first);
return NULL;
}
/*
* Fix sconfig's burst size according to dw_dmac. We need to convert them as:
* 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3.
*
* NOTE: burst size 2 is not supported by controller.
*
* This can be done by finding least significant bit set: n & (n - 1)
*/
static inline void convert_burst(u32 *maxburst)
{
if (*maxburst > 1)
*maxburst = fls(*maxburst) - 2;
else
*maxburst = 0;
}
static int
set_runtime_config(struct dma_chan *chan, struct dma_slave_config *sconfig)
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
/* Check if it is chan is configured for slave transfers */
if (!chan->private)
return -EINVAL;
memcpy(&dwc->dma_sconfig, sconfig, sizeof(*sconfig));
convert_burst(&dwc->dma_sconfig.src_maxburst);
convert_burst(&dwc->dma_sconfig.dst_maxburst);
return 0;
}
static int dwc_control(struct dma_chan *chan, enum dma_ctrl_cmd cmd,
unsigned long arg)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
struct dw_dma *dw = to_dw_dma(chan->device);
struct dw_desc *desc, *_desc;
unsigned long flags;
u32 cfglo;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
LIST_HEAD(list);
if (cmd == DMA_PAUSE) {
spin_lock_irqsave(&dwc->lock, flags);
cfglo = channel_readl(dwc, CFG_LO);
channel_writel(dwc, CFG_LO, cfglo | DWC_CFGL_CH_SUSP);
while (!(channel_readl(dwc, CFG_LO) & DWC_CFGL_FIFO_EMPTY))
cpu_relax();
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dwc->paused = true;
spin_unlock_irqrestore(&dwc->lock, flags);
} else if (cmd == DMA_RESUME) {
if (!dwc->paused)
return 0;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
spin_lock_irqsave(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
cfglo = channel_readl(dwc, CFG_LO);
channel_writel(dwc, CFG_LO, cfglo & ~DWC_CFGL_CH_SUSP);
dwc->paused = false;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
spin_unlock_irqrestore(&dwc->lock, flags);
} else if (cmd == DMA_TERMINATE_ALL) {
spin_lock_irqsave(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
clear_bit(DW_DMA_IS_SOFT_LLP, &dwc->flags);
dwc_chan_disable(dw, dwc);
dwc->paused = false;
/* active_list entries will end up before queued entries */
list_splice_init(&dwc->queue, &list);
list_splice_init(&dwc->active_list, &list);
spin_unlock_irqrestore(&dwc->lock, flags);
/* Flush all pending and queued descriptors */
list_for_each_entry_safe(desc, _desc, &list, desc_node)
dwc_descriptor_complete(dwc, desc, false);
} else if (cmd == DMA_SLAVE_CONFIG) {
return set_runtime_config(chan, (struct dma_slave_config *)arg);
} else {
return -ENXIO;
}
return 0;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
static enum dma_status
dwc_tx_status(struct dma_chan *chan,
dma_cookie_t cookie,
struct dma_tx_state *txstate)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
enum dma_status ret;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
ret = dma_cookie_status(chan, cookie, txstate);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (ret != DMA_SUCCESS) {
dwc_scan_descriptors(to_dw_dma(chan->device), dwc);
ret = dma_cookie_status(chan, cookie, txstate);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
if (ret != DMA_SUCCESS)
dma_set_residue(txstate, dwc_first_active(dwc)->len);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (dwc->paused)
return DMA_PAUSED;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
return ret;
}
static void dwc_issue_pending(struct dma_chan *chan)
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
if (!list_empty(&dwc->queue))
dwc_scan_descriptors(to_dw_dma(chan->device), dwc);
}
static int dwc_alloc_chan_resources(struct dma_chan *chan)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
struct dw_dma *dw = to_dw_dma(chan->device);
struct dw_desc *desc;
int i;
unsigned long flags;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dev_vdbg(chan2dev(chan), "%s\n", __func__);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/* ASSERT: channel is idle */
if (dma_readl(dw, CH_EN) & dwc->mask) {
dev_dbg(chan2dev(chan), "DMA channel not idle?\n");
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
return -EIO;
}
dma_cookie_init(chan);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/*
* NOTE: some controllers may have additional features that we
* need to initialize here, like "scatter-gather" (which
* doesn't mean what you think it means), and status writeback.
*/
spin_lock_irqsave(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
i = dwc->descs_allocated;
while (dwc->descs_allocated < NR_DESCS_PER_CHANNEL) {
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
desc = kzalloc(sizeof(struct dw_desc), GFP_KERNEL);
if (!desc) {
dev_info(chan2dev(chan),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
"only allocated %d descriptors\n", i);
spin_lock_irqsave(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
break;
}
INIT_LIST_HEAD(&desc->tx_list);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dma_async_tx_descriptor_init(&desc->txd, chan);
desc->txd.tx_submit = dwc_tx_submit;
desc->txd.flags = DMA_CTRL_ACK;
desc->txd.phys = dma_map_single(chan2parent(chan), &desc->lli,
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
sizeof(desc->lli), DMA_TO_DEVICE);
dwc_desc_put(dwc, desc);
spin_lock_irqsave(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
i = ++dwc->descs_allocated;
}
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dev_dbg(chan2dev(chan), "%s: allocated %d descriptors\n", __func__, i);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
return i;
}
static void dwc_free_chan_resources(struct dma_chan *chan)
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
struct dw_dma *dw = to_dw_dma(chan->device);
struct dw_desc *desc, *_desc;
unsigned long flags;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
LIST_HEAD(list);
dev_dbg(chan2dev(chan), "%s: descs allocated=%u\n", __func__,
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dwc->descs_allocated);
/* ASSERT: channel is idle */
BUG_ON(!list_empty(&dwc->active_list));
BUG_ON(!list_empty(&dwc->queue));
BUG_ON(dma_readl(to_dw_dma(chan->device), CH_EN) & dwc->mask);
spin_lock_irqsave(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
list_splice_init(&dwc->free_list, &list);
dwc->descs_allocated = 0;
dwc->initialized = false;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/* Disable interrupts */
channel_clear_bit(dw, MASK.XFER, dwc->mask);
channel_clear_bit(dw, MASK.ERROR, dwc->mask);
spin_unlock_irqrestore(&dwc->lock, flags);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
list_for_each_entry_safe(desc, _desc, &list, desc_node) {
dev_vdbg(chan2dev(chan), " freeing descriptor %p\n", desc);
dma_unmap_single(chan2parent(chan), desc->txd.phys,
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
sizeof(desc->lli), DMA_TO_DEVICE);
kfree(desc);
}
dev_vdbg(chan2dev(chan), "%s: done\n", __func__);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
/* --------------------- Cyclic DMA API extensions -------------------- */
/**
* dw_dma_cyclic_start - start the cyclic DMA transfer
* @chan: the DMA channel to start
*
* Must be called with soft interrupts disabled. Returns zero on success or
* -errno on failure.
*/
int dw_dma_cyclic_start(struct dma_chan *chan)
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
struct dw_dma *dw = to_dw_dma(dwc->chan.device);
unsigned long flags;
if (!test_bit(DW_DMA_IS_CYCLIC, &dwc->flags)) {
dev_err(chan2dev(&dwc->chan), "missing prep for cyclic DMA\n");
return -ENODEV;
}
spin_lock_irqsave(&dwc->lock, flags);
/* assert channel is idle */
if (dma_readl(dw, CH_EN) & dwc->mask) {
dev_err(chan2dev(&dwc->chan),
"BUG: Attempted to start non-idle channel\n");
dwc_dump_chan_regs(dwc);
spin_unlock_irqrestore(&dwc->lock, flags);
return -EBUSY;
}
dma_writel(dw, CLEAR.ERROR, dwc->mask);
dma_writel(dw, CLEAR.XFER, dwc->mask);
/* setup DMAC channel registers */
channel_writel(dwc, LLP, dwc->cdesc->desc[0]->txd.phys);
channel_writel(dwc, CTL_LO, DWC_CTLL_LLP_D_EN | DWC_CTLL_LLP_S_EN);
channel_writel(dwc, CTL_HI, 0);
channel_set_bit(dw, CH_EN, dwc->mask);
spin_unlock_irqrestore(&dwc->lock, flags);
return 0;
}
EXPORT_SYMBOL(dw_dma_cyclic_start);
/**
* dw_dma_cyclic_stop - stop the cyclic DMA transfer
* @chan: the DMA channel to stop
*
* Must be called with soft interrupts disabled.
*/
void dw_dma_cyclic_stop(struct dma_chan *chan)
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
struct dw_dma *dw = to_dw_dma(dwc->chan.device);
unsigned long flags;
spin_lock_irqsave(&dwc->lock, flags);
dwc_chan_disable(dw, dwc);
spin_unlock_irqrestore(&dwc->lock, flags);
}
EXPORT_SYMBOL(dw_dma_cyclic_stop);
/**
* dw_dma_cyclic_prep - prepare the cyclic DMA transfer
* @chan: the DMA channel to prepare
* @buf_addr: physical DMA address where the buffer starts
* @buf_len: total number of bytes for the entire buffer
* @period_len: number of bytes for each period
* @direction: transfer direction, to or from device
*
* Must be called before trying to start the transfer. Returns a valid struct
* dw_cyclic_desc if successful or an ERR_PTR(-errno) if not successful.
*/
struct dw_cyclic_desc *dw_dma_cyclic_prep(struct dma_chan *chan,
dma_addr_t buf_addr, size_t buf_len, size_t period_len,
enum dma_transfer_direction direction)
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
struct dma_slave_config *sconfig = &dwc->dma_sconfig;
struct dw_cyclic_desc *cdesc;
struct dw_cyclic_desc *retval = NULL;
struct dw_desc *desc;
struct dw_desc *last = NULL;
unsigned long was_cyclic;
unsigned int reg_width;
unsigned int periods;
unsigned int i;
unsigned long flags;
spin_lock_irqsave(&dwc->lock, flags);
if (dwc->nollp) {
spin_unlock_irqrestore(&dwc->lock, flags);
dev_dbg(chan2dev(&dwc->chan),
"channel doesn't support LLP transfers\n");
return ERR_PTR(-EINVAL);
}
if (!list_empty(&dwc->queue) || !list_empty(&dwc->active_list)) {
spin_unlock_irqrestore(&dwc->lock, flags);
dev_dbg(chan2dev(&dwc->chan),
"queue and/or active list are not empty\n");
return ERR_PTR(-EBUSY);
}
was_cyclic = test_and_set_bit(DW_DMA_IS_CYCLIC, &dwc->flags);
spin_unlock_irqrestore(&dwc->lock, flags);
if (was_cyclic) {
dev_dbg(chan2dev(&dwc->chan),
"channel already prepared for cyclic DMA\n");
return ERR_PTR(-EBUSY);
}
retval = ERR_PTR(-EINVAL);
if (direction == DMA_MEM_TO_DEV)
reg_width = __ffs(sconfig->dst_addr_width);
else
reg_width = __ffs(sconfig->src_addr_width);
periods = buf_len / period_len;
/* Check for too big/unaligned periods and unaligned DMA buffer. */
if (period_len > (dwc->block_size << reg_width))
goto out_err;
if (unlikely(period_len & ((1 << reg_width) - 1)))
goto out_err;
if (unlikely(buf_addr & ((1 << reg_width) - 1)))
goto out_err;
if (unlikely(!(direction & (DMA_MEM_TO_DEV | DMA_DEV_TO_MEM))))
goto out_err;
retval = ERR_PTR(-ENOMEM);
if (periods > NR_DESCS_PER_CHANNEL)
goto out_err;
cdesc = kzalloc(sizeof(struct dw_cyclic_desc), GFP_KERNEL);
if (!cdesc)
goto out_err;
cdesc->desc = kzalloc(sizeof(struct dw_desc *) * periods, GFP_KERNEL);
if (!cdesc->desc)
goto out_err_alloc;
for (i = 0; i < periods; i++) {
desc = dwc_desc_get(dwc);
if (!desc)
goto out_err_desc_get;
switch (direction) {
case DMA_MEM_TO_DEV:
desc->lli.dar = sconfig->dst_addr;
desc->lli.sar = buf_addr + (period_len * i);
desc->lli.ctllo = (DWC_DEFAULT_CTLLO(chan)
| DWC_CTLL_DST_WIDTH(reg_width)
| DWC_CTLL_SRC_WIDTH(reg_width)
| DWC_CTLL_DST_FIX
| DWC_CTLL_SRC_INC
| DWC_CTLL_INT_EN);
desc->lli.ctllo |= sconfig->device_fc ?
DWC_CTLL_FC(DW_DMA_FC_P_M2P) :
DWC_CTLL_FC(DW_DMA_FC_D_M2P);
break;
case DMA_DEV_TO_MEM:
desc->lli.dar = buf_addr + (period_len * i);
desc->lli.sar = sconfig->src_addr;
desc->lli.ctllo = (DWC_DEFAULT_CTLLO(chan)
| DWC_CTLL_SRC_WIDTH(reg_width)
| DWC_CTLL_DST_WIDTH(reg_width)
| DWC_CTLL_DST_INC
| DWC_CTLL_SRC_FIX
| DWC_CTLL_INT_EN);
desc->lli.ctllo |= sconfig->device_fc ?
DWC_CTLL_FC(DW_DMA_FC_P_P2M) :
DWC_CTLL_FC(DW_DMA_FC_D_P2M);
break;
default:
break;
}
desc->lli.ctlhi = (period_len >> reg_width);
cdesc->desc[i] = desc;
if (last) {
last->lli.llp = desc->txd.phys;
dma_sync_single_for_device(chan2parent(chan),
last->txd.phys, sizeof(last->lli),
DMA_TO_DEVICE);
}
last = desc;
}
/* lets make a cyclic list */
last->lli.llp = cdesc->desc[0]->txd.phys;
dma_sync_single_for_device(chan2parent(chan), last->txd.phys,
sizeof(last->lli), DMA_TO_DEVICE);
dev_dbg(chan2dev(&dwc->chan), "cyclic prepared buf 0x%llx len %zu "
"period %zu periods %d\n", (unsigned long long)buf_addr,
buf_len, period_len, periods);
cdesc->periods = periods;
dwc->cdesc = cdesc;
return cdesc;
out_err_desc_get:
while (i--)
dwc_desc_put(dwc, cdesc->desc[i]);
out_err_alloc:
kfree(cdesc);
out_err:
clear_bit(DW_DMA_IS_CYCLIC, &dwc->flags);
return (struct dw_cyclic_desc *)retval;
}
EXPORT_SYMBOL(dw_dma_cyclic_prep);
/**
* dw_dma_cyclic_free - free a prepared cyclic DMA transfer
* @chan: the DMA channel to free
*/
void dw_dma_cyclic_free(struct dma_chan *chan)
{
struct dw_dma_chan *dwc = to_dw_dma_chan(chan);
struct dw_dma *dw = to_dw_dma(dwc->chan.device);
struct dw_cyclic_desc *cdesc = dwc->cdesc;
int i;
unsigned long flags;
dev_dbg(chan2dev(&dwc->chan), "%s\n", __func__);
if (!cdesc)
return;
spin_lock_irqsave(&dwc->lock, flags);
dwc_chan_disable(dw, dwc);
dma_writel(dw, CLEAR.ERROR, dwc->mask);
dma_writel(dw, CLEAR.XFER, dwc->mask);
spin_unlock_irqrestore(&dwc->lock, flags);
for (i = 0; i < cdesc->periods; i++)
dwc_desc_put(dwc, cdesc->desc[i]);
kfree(cdesc->desc);
kfree(cdesc);
clear_bit(DW_DMA_IS_CYCLIC, &dwc->flags);
}
EXPORT_SYMBOL(dw_dma_cyclic_free);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/*----------------------------------------------------------------------*/
static void dw_dma_off(struct dw_dma *dw)
{
int i;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dma_writel(dw, CFG, 0);
channel_clear_bit(dw, MASK.XFER, dw->all_chan_mask);
channel_clear_bit(dw, MASK.SRC_TRAN, dw->all_chan_mask);
channel_clear_bit(dw, MASK.DST_TRAN, dw->all_chan_mask);
channel_clear_bit(dw, MASK.ERROR, dw->all_chan_mask);
while (dma_readl(dw, CFG) & DW_CFG_DMA_EN)
cpu_relax();
for (i = 0; i < dw->dma.chancnt; i++)
dw->chan[i].initialized = false;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
static int __devinit dw_probe(struct platform_device *pdev)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
{
struct dw_dma_platform_data *pdata;
struct resource *io;
struct dw_dma *dw;
size_t size;
void __iomem *regs;
bool autocfg;
unsigned int dw_params;
unsigned int nr_channels;
unsigned int max_blk_size = 0;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
int irq;
int err;
int i;
pdata = dev_get_platdata(&pdev->dev);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (!pdata || pdata->nr_channels > DW_DMA_MAX_NR_CHANNELS)
return -EINVAL;
io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!io)
return -EINVAL;
irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
regs = devm_request_and_ioremap(&pdev->dev, io);
if (!regs)
return -EBUSY;
dw_params = dma_read_byaddr(regs, DW_PARAMS);
autocfg = dw_params >> DW_PARAMS_EN & 0x1;
if (autocfg)
nr_channels = (dw_params >> DW_PARAMS_NR_CHAN & 0x7) + 1;
else
nr_channels = pdata->nr_channels;
size = sizeof(struct dw_dma) + nr_channels * sizeof(struct dw_dma_chan);
dw = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (!dw)
return -ENOMEM;
dw->clk = devm_clk_get(&pdev->dev, "hclk");
if (IS_ERR(dw->clk))
return PTR_ERR(dw->clk);
clk_prepare_enable(dw->clk);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dw->regs = regs;
/* get hardware configuration parameters */
if (autocfg) {
max_blk_size = dma_readl(dw, MAX_BLK_SIZE);
dw->nr_masters = (dw_params >> DW_PARAMS_NR_MASTER & 3) + 1;
for (i = 0; i < dw->nr_masters; i++) {
dw->data_width[i] =
(dw_params >> DW_PARAMS_DATA_WIDTH(i) & 3) + 2;
}
} else {
dw->nr_masters = pdata->nr_masters;
memcpy(dw->data_width, pdata->data_width, 4);
}
/* Calculate all channel mask before DMA setup */
dw->all_chan_mask = (1 << nr_channels) - 1;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/* force dma off, just in case */
dw_dma_off(dw);
/* disable BLOCK interrupts as well */
channel_clear_bit(dw, MASK.BLOCK, dw->all_chan_mask);
err = devm_request_irq(&pdev->dev, irq, dw_dma_interrupt, 0,
"dw_dmac", dw);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
if (err)
return err;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
platform_set_drvdata(pdev, dw);
tasklet_init(&dw->tasklet, dw_dma_tasklet, (unsigned long)dw);
INIT_LIST_HEAD(&dw->dma.channels);
for (i = 0; i < nr_channels; i++) {
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
struct dw_dma_chan *dwc = &dw->chan[i];
int r = nr_channels - i - 1;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dwc->chan.device = &dw->dma;
dma_cookie_init(&dwc->chan);
if (pdata->chan_allocation_order == CHAN_ALLOCATION_ASCENDING)
list_add_tail(&dwc->chan.device_node,
&dw->dma.channels);
else
list_add(&dwc->chan.device_node, &dw->dma.channels);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
/* 7 is highest priority & 0 is lowest. */
if (pdata->chan_priority == CHAN_PRIORITY_ASCENDING)
dwc->priority = r;
else
dwc->priority = i;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dwc->ch_regs = &__dw_regs(dw)->CHAN[i];
spin_lock_init(&dwc->lock);
dwc->mask = 1 << i;
INIT_LIST_HEAD(&dwc->active_list);
INIT_LIST_HEAD(&dwc->queue);
INIT_LIST_HEAD(&dwc->free_list);
channel_clear_bit(dw, CH_EN, dwc->mask);
dwc->dw = dw;
/* hardware configuration */
if (autocfg) {
unsigned int dwc_params;
dwc_params = dma_read_byaddr(regs + r * sizeof(u32),
DWC_PARAMS);
/* Decode maximum block size for given channel. The
* stored 4 bit value represents blocks from 0x00 for 3
* up to 0x0a for 4095. */
dwc->block_size =
(4 << ((max_blk_size >> 4 * i) & 0xf)) - 1;
dwc->nollp =
(dwc_params >> DWC_PARAMS_MBLK_EN & 0x1) == 0;
} else {
dwc->block_size = pdata->block_size;
/* Check if channel supports multi block transfer */
channel_writel(dwc, LLP, 0xfffffffc);
dwc->nollp =
(channel_readl(dwc, LLP) & 0xfffffffc) == 0;
channel_writel(dwc, LLP, 0);
}
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
/* Clear all interrupts on all channels. */
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dma_writel(dw, CLEAR.XFER, dw->all_chan_mask);
dma_writel(dw, CLEAR.BLOCK, dw->all_chan_mask);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dma_writel(dw, CLEAR.SRC_TRAN, dw->all_chan_mask);
dma_writel(dw, CLEAR.DST_TRAN, dw->all_chan_mask);
dma_writel(dw, CLEAR.ERROR, dw->all_chan_mask);
dma_cap_set(DMA_MEMCPY, dw->dma.cap_mask);
dma_cap_set(DMA_SLAVE, dw->dma.cap_mask);
if (pdata->is_private)
dma_cap_set(DMA_PRIVATE, dw->dma.cap_mask);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dw->dma.dev = &pdev->dev;
dw->dma.device_alloc_chan_resources = dwc_alloc_chan_resources;
dw->dma.device_free_chan_resources = dwc_free_chan_resources;
dw->dma.device_prep_dma_memcpy = dwc_prep_dma_memcpy;
dw->dma.device_prep_slave_sg = dwc_prep_slave_sg;
dw->dma.device_control = dwc_control;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dw->dma.device_tx_status = dwc_tx_status;
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dw->dma.device_issue_pending = dwc_issue_pending;
dma_writel(dw, CFG, DW_CFG_DMA_EN);
printk(KERN_INFO "%s: DesignWare DMA Controller, %d channels\n",
dev_name(&pdev->dev), nr_channels);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dma_async_device_register(&dw->dma);
return 0;
}
static int __devexit dw_remove(struct platform_device *pdev)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
{
struct dw_dma *dw = platform_get_drvdata(pdev);
struct dw_dma_chan *dwc, *_dwc;
dw_dma_off(dw);
dma_async_device_unregister(&dw->dma);
tasklet_kill(&dw->tasklet);
list_for_each_entry_safe(dwc, _dwc, &dw->dma.channels,
chan.device_node) {
list_del(&dwc->chan.device_node);
channel_clear_bit(dw, CH_EN, dwc->mask);
}
return 0;
}
static void dw_shutdown(struct platform_device *pdev)
{
struct dw_dma *dw = platform_get_drvdata(pdev);
dw_dma_off(platform_get_drvdata(pdev));
clk_disable_unprepare(dw->clk);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
}
static int dw_suspend_noirq(struct device *dev)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
{
struct platform_device *pdev = to_platform_device(dev);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
struct dw_dma *dw = platform_get_drvdata(pdev);
dw_dma_off(platform_get_drvdata(pdev));
clk_disable_unprepare(dw->clk);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
return 0;
}
static int dw_resume_noirq(struct device *dev)
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
{
struct platform_device *pdev = to_platform_device(dev);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
struct dw_dma *dw = platform_get_drvdata(pdev);
clk_prepare_enable(dw->clk);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
dma_writel(dw, CFG, DW_CFG_DMA_EN);
return 0;
}
static const struct dev_pm_ops dw_dev_pm_ops = {
.suspend_noirq = dw_suspend_noirq,
.resume_noirq = dw_resume_noirq,
.freeze_noirq = dw_suspend_noirq,
.thaw_noirq = dw_resume_noirq,
.restore_noirq = dw_resume_noirq,
.poweroff_noirq = dw_suspend_noirq,
};
#ifdef CONFIG_OF
static const struct of_device_id dw_dma_id_table[] = {
{ .compatible = "snps,dma-spear1340" },
{}
};
MODULE_DEVICE_TABLE(of, dw_dma_id_table);
#endif
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
static struct platform_driver dw_driver = {
.remove = __devexit_p(dw_remove),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
.shutdown = dw_shutdown,
.driver = {
.name = "dw_dmac",
.pm = &dw_dev_pm_ops,
.of_match_table = of_match_ptr(dw_dma_id_table),
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
},
};
static int __init dw_init(void)
{
return platform_driver_probe(&dw_driver, dw_probe);
}
subsys_initcall(dw_init);
dmaengine: Driver for the Synopsys DesignWare DMA controller This adds a driver for the Synopsys DesignWare DMA controller (aka DMACA on AVR32 systems.) This DMA controller can be found integrated on the AT32AP7000 chip and is primarily meant for peripheral DMA transfer, but can also be used for memory-to-memory transfers. This patch is based on a driver from David Brownell which was based on an older version of the DMA Engine framework. It also implements the proposed extensions to the DMA Engine API for slave DMA operations. The dmatest client shows no problems, but there may still be room for improvement performance-wise. DMA slave transfer performance is definitely "good enough"; reading 100 MiB from an SD card running at ~20 MHz yields ~7.2 MiB/s average transfer rate. Full documentation for this controller can be found in the Synopsys DW AHB DMAC Databook: http://www.synopsys.com/designware/docs/iip/DW_ahb_dmac/latest/doc/dw_ahb_dmac_db.pdf The controller has lots of implementation options, so it's usually a good idea to check the data sheet of the chip it's intergrated on as well. The AT32AP7000 data sheet can be found here: http://www.atmel.com/dyn/products/datasheets.asp?family_id=682 Changes since v4: * Use client_count instead of dma_chan_is_in_use() * Add missing include * Unmap buffers unless client told us not to Changes since v3: * Update to latest DMA engine and DMA slave APIs * Embed the hw descriptor into the sw descriptor * Clean up and update MODULE_DESCRIPTION, copyright date, etc. Changes since v2: * Dequeue all pending transfers in terminate_all() * Rename dw_dmac.h -> dw_dmac_regs.h * Define and use controller-specific dma_slave data * Fix up a few outdated comments * Define hardware registers as structs (doesn't generate better code, unfortunately, but it looks nicer.) * Get number of channels from platform_data instead of hardcoding it based on CONFIG_WHATEVER_CPU. * Give slave clients exclusive access to the channel Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>, Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2008-07-08 18:59:42 +00:00
static void __exit dw_exit(void)
{
platform_driver_unregister(&dw_driver);
}
module_exit(dw_exit);
MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("Synopsys DesignWare DMA Controller driver");
MODULE_AUTHOR("Haavard Skinnemoen (Atmel)");
MODULE_AUTHOR("Viresh Kumar <viresh.linux@gmail.com>");