linux/drivers/scsi/g_NCR5380.h

85 lines
2.2 KiB
C
Raw Normal View History

/*
* Generic Generic NCR5380 driver defines
*
* Copyright 1993, Drew Eckhardt
* Visionary Computing
* (Unix and Linux consulting and custom programming)
* drew@colorado.edu
* +1 (303) 440-4894
*
* NCR53C400 extensions (c) 1994,1995,1996, Kevin Lentin
* K.Lentin@cs.monash.edu.au
*/
#ifndef GENERIC_NCR5380_H
#define GENERIC_NCR5380_H
#define __STRVAL(x) #x
#define STRVAL(x) __STRVAL(x)
#ifndef SCSI_G_NCR5380_MEM
#define DRV_MODULE_NAME "g_NCR5380"
#define NCR5380_map_type int
#define NCR5380_map_name port
#define NCR5380_read(reg) \
inb(instance->io_port + (reg))
#define NCR5380_write(reg, value) \
outb(value, instance->io_port + (reg))
#define NCR5380_implementation_fields \
int c400_ctl_status; \
int c400_blk_cnt; \
int c400_host_buf; \
int io_width;
#else
/* therefore SCSI_G_NCR5380_MEM */
#define DRV_MODULE_NAME "g_NCR5380_mmio"
#define NCR5380_map_type unsigned long
#define NCR5380_map_name base
#define NCR53C400_mem_base 0x3880
#define NCR53C400_host_buffer 0x3900
g_ncr5380: Remove CONFIG_SCSI_GENERIC_NCR53C400 This change brings a number of improvements: fewer macros, better test coverage, simpler code and sane Kconfig options. The downside is a small chance of incompatibility (which seems unavoidable). CONFIG_SCSI_GENERIC_NCR53C400 exists to enable or inhibit pseudo DMA transfers when the driver is used with 53C400-compatible cards. Thanks to Ondrej Zary's patches, PDMA now works which means it can be enabled unconditionally. Due to bad design, CONFIG_SCSI_GENERIC_NCR53C400 ties together unrelated functionality as it sets both PSEUDO_DMA and BIOSPARAM macros. This patch effectively enables PSEUDO_DMA and disables BIOSPARAM. The defconfigs and the Kconfig default leave CONFIG_SCSI_GENERIC_NCR53C400 undefined. Red Hat 9 and CentOS 2.1 were the same. This leaves both PSEUDO_DMA and BIOSPARAM disabled. The effect of this patch should be better performance from enabling PSEUDO_DMA. On the other hand, Debian 4 and SLES 10 had CONFIG_SCSI_GENERIC_NCR53C400 enabled, so both PSEUDO_DMA and BIOSPARAM were enabled. This patch might affect configurations like this by disabling BIOSPARAM. My best guess is that this could be a problem only in the vanishingly rare case that 1) the CHS values stored in the boot device partition table are wrong and 2) a 5380 card is in use (because PDMA on 53C400 used to be broken). Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-03-23 10:10:10 +00:00
#define NCR53C400_region_size 0x3a00
#define NCR5380_read(reg) \
readb(((struct NCR5380_hostdata *)shost_priv(instance))->iomem + \
NCR53C400_mem_base + (reg))
#define NCR5380_write(reg, value) \
writeb(value, ((struct NCR5380_hostdata *)shost_priv(instance))->iomem + \
NCR53C400_mem_base + (reg))
#define NCR5380_implementation_fields \
void __iomem *iomem; \
g_ncr5380: Remove CONFIG_SCSI_GENERIC_NCR53C400 This change brings a number of improvements: fewer macros, better test coverage, simpler code and sane Kconfig options. The downside is a small chance of incompatibility (which seems unavoidable). CONFIG_SCSI_GENERIC_NCR53C400 exists to enable or inhibit pseudo DMA transfers when the driver is used with 53C400-compatible cards. Thanks to Ondrej Zary's patches, PDMA now works which means it can be enabled unconditionally. Due to bad design, CONFIG_SCSI_GENERIC_NCR53C400 ties together unrelated functionality as it sets both PSEUDO_DMA and BIOSPARAM macros. This patch effectively enables PSEUDO_DMA and disables BIOSPARAM. The defconfigs and the Kconfig default leave CONFIG_SCSI_GENERIC_NCR53C400 undefined. Red Hat 9 and CentOS 2.1 were the same. This leaves both PSEUDO_DMA and BIOSPARAM disabled. The effect of this patch should be better performance from enabling PSEUDO_DMA. On the other hand, Debian 4 and SLES 10 had CONFIG_SCSI_GENERIC_NCR53C400 enabled, so both PSEUDO_DMA and BIOSPARAM were enabled. This patch might affect configurations like this by disabling BIOSPARAM. My best guess is that this could be a problem only in the vanishingly rare case that 1) the CHS values stored in the boot device partition table are wrong and 2) a 5380 card is in use (because PDMA on 53C400 used to be broken). Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Hannes Reinecke <hare@suse.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2016-03-23 10:10:10 +00:00
resource_size_t iomem_size; \
int c400_ctl_status; \
int c400_blk_cnt; \
int c400_host_buf;
#endif
#define NCR5380_dma_xfer_len(instance, cmd, phase) \
generic_NCR5380_dma_xfer_len(instance, cmd)
#define NCR5380_dma_recv_setup generic_NCR5380_pread
#define NCR5380_dma_send_setup generic_NCR5380_pwrite
#define NCR5380_dma_residual(instance) (0)
#define NCR5380_intr generic_NCR5380_intr
#define NCR5380_queue_command generic_NCR5380_queue_command
#define NCR5380_abort generic_NCR5380_abort
#define NCR5380_bus_reset generic_NCR5380_bus_reset
#define NCR5380_info generic_NCR5380_info
#define NCR5380_io_delay(x) udelay(x)
#define BOARD_NCR5380 0
#define BOARD_NCR53C400 1
#define BOARD_NCR53C400A 2
#define BOARD_DTC3181E 3
#define BOARD_HP_C2502 4
#endif /* GENERIC_NCR5380_H */