linux/drivers/mtd/spi-nor/hisi-sfc.c

508 lines
12 KiB
C
Raw Normal View History

/*
* HiSilicon SPI Nor Flash Controller Driver
*
* Copyright (c) 2015-2016 HiSilicon Technologies Co., Ltd.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#include <linux/bitops.h>
#include <linux/clk.h>
#include <linux/dma-mapping.h>
#include <linux/iopoll.h>
#include <linux/module.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/spi-nor.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
/* Hardware register offsets and field definitions */
#define FMC_CFG 0x00
#define FMC_CFG_OP_MODE_MASK BIT_MASK(0)
#define FMC_CFG_OP_MODE_BOOT 0
#define FMC_CFG_OP_MODE_NORMAL 1
#define FMC_CFG_FLASH_SEL(type) (((type) & 0x3) << 1)
#define FMC_CFG_FLASH_SEL_MASK 0x6
#define FMC_ECC_TYPE(type) (((type) & 0x7) << 5)
#define FMC_ECC_TYPE_MASK GENMASK(7, 5)
#define SPI_NOR_ADDR_MODE_MASK BIT_MASK(10)
#define SPI_NOR_ADDR_MODE_3BYTES (0x0 << 10)
#define SPI_NOR_ADDR_MODE_4BYTES (0x1 << 10)
#define FMC_GLOBAL_CFG 0x04
#define FMC_GLOBAL_CFG_WP_ENABLE BIT(6)
#define FMC_SPI_TIMING_CFG 0x08
#define TIMING_CFG_TCSH(nr) (((nr) & 0xf) << 8)
#define TIMING_CFG_TCSS(nr) (((nr) & 0xf) << 4)
#define TIMING_CFG_TSHSL(nr) ((nr) & 0xf)
#define CS_HOLD_TIME 0x6
#define CS_SETUP_TIME 0x6
#define CS_DESELECT_TIME 0xf
#define FMC_INT 0x18
#define FMC_INT_OP_DONE BIT(0)
#define FMC_INT_CLR 0x20
#define FMC_CMD 0x24
#define FMC_CMD_CMD1(cmd) ((cmd) & 0xff)
#define FMC_ADDRL 0x2c
#define FMC_OP_CFG 0x30
#define OP_CFG_FM_CS(cs) ((cs) << 11)
#define OP_CFG_MEM_IF_TYPE(type) (((type) & 0x7) << 7)
#define OP_CFG_ADDR_NUM(addr) (((addr) & 0x7) << 4)
#define OP_CFG_DUMMY_NUM(dummy) ((dummy) & 0xf)
#define FMC_DATA_NUM 0x38
#define FMC_DATA_NUM_CNT(cnt) ((cnt) & GENMASK(13, 0))
#define FMC_OP 0x3c
#define FMC_OP_DUMMY_EN BIT(8)
#define FMC_OP_CMD1_EN BIT(7)
#define FMC_OP_ADDR_EN BIT(6)
#define FMC_OP_WRITE_DATA_EN BIT(5)
#define FMC_OP_READ_DATA_EN BIT(2)
#define FMC_OP_READ_STATUS_EN BIT(1)
#define FMC_OP_REG_OP_START BIT(0)
#define FMC_DMA_LEN 0x40
#define FMC_DMA_LEN_SET(len) ((len) & GENMASK(27, 0))
#define FMC_DMA_SADDR_D0 0x4c
#define HIFMC_DMA_MAX_LEN (4096)
#define HIFMC_DMA_MASK (HIFMC_DMA_MAX_LEN - 1)
#define FMC_OP_DMA 0x68
#define OP_CTRL_RD_OPCODE(code) (((code) & 0xff) << 16)
#define OP_CTRL_WR_OPCODE(code) (((code) & 0xff) << 8)
#define OP_CTRL_RW_OP(op) ((op) << 1)
#define OP_CTRL_DMA_OP_READY BIT(0)
#define FMC_OP_READ 0x0
#define FMC_OP_WRITE 0x1
#define FMC_WAIT_TIMEOUT 1000000
enum hifmc_iftype {
IF_TYPE_STD,
IF_TYPE_DUAL,
IF_TYPE_DIO,
IF_TYPE_QUAD,
IF_TYPE_QIO,
};
struct hifmc_priv {
u32 chipselect;
u32 clkrate;
struct hifmc_host *host;
};
#define HIFMC_MAX_CHIP_NUM 2
struct hifmc_host {
struct device *dev;
struct mutex lock;
void __iomem *regbase;
void __iomem *iobase;
struct clk *clk;
void *buffer;
dma_addr_t dma_buffer;
struct spi_nor *nor[HIFMC_MAX_CHIP_NUM];
u32 num_chip;
};
static inline int wait_op_finish(struct hifmc_host *host)
{
u32 reg;
return readl_poll_timeout(host->regbase + FMC_INT, reg,
(reg & FMC_INT_OP_DONE), 0, FMC_WAIT_TIMEOUT);
}
mtd: spi-nor: introduce SPI 1-2-2 and SPI 1-4-4 protocols This patch changes the prototype of spi_nor_scan(): its 3rd parameter is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor framework about the actual hardware capabilities supported by the SPI controller and its driver. Besides, this patch also introduces a new 'struct spi_nor_flash_parameter' telling the spi-nor framework about the hardware capabilities supported by the SPI flash memory and the associated settings required to use those hardware caps. Then, to improve the readability of spi_nor_scan(), the discovery of the memory settings and the memory initialization are now split into two dedicated functions. 1 - spi_nor_init_params() The spi_nor_init_params() function is responsible for initializing the 'struct spi_nor_flash_parameter'. Currently this structure is filled with legacy values but further patches will allow to override some parameter values dynamically, for instance by reading the JESD216 Serial Flash Discoverable Parameter (SFDP) tables from the SPI memory. The spi_nor_init_params() function only deals with the hardware capabilities of the SPI flash memory: especially it doesn't care about the hardware capabilities supported by the SPI controller. 2 - spi_nor_setup() The second function is called once the 'struct spi_nor_flash_parameter' has been initialized by spi_nor_init_params(). With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps', the new argument of spi_nor_scan(), spi_nor_setup() computes the best match between hardware caps supported by both the (Q)SPI memory and controller hence selecting the relevant settings for (Fast) Read and Page Program operations. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
2017-04-25 20:08:46 +00:00
static int get_if_type(enum spi_nor_protocol proto)
{
enum hifmc_iftype if_type;
mtd: spi-nor: introduce SPI 1-2-2 and SPI 1-4-4 protocols This patch changes the prototype of spi_nor_scan(): its 3rd parameter is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor framework about the actual hardware capabilities supported by the SPI controller and its driver. Besides, this patch also introduces a new 'struct spi_nor_flash_parameter' telling the spi-nor framework about the hardware capabilities supported by the SPI flash memory and the associated settings required to use those hardware caps. Then, to improve the readability of spi_nor_scan(), the discovery of the memory settings and the memory initialization are now split into two dedicated functions. 1 - spi_nor_init_params() The spi_nor_init_params() function is responsible for initializing the 'struct spi_nor_flash_parameter'. Currently this structure is filled with legacy values but further patches will allow to override some parameter values dynamically, for instance by reading the JESD216 Serial Flash Discoverable Parameter (SFDP) tables from the SPI memory. The spi_nor_init_params() function only deals with the hardware capabilities of the SPI flash memory: especially it doesn't care about the hardware capabilities supported by the SPI controller. 2 - spi_nor_setup() The second function is called once the 'struct spi_nor_flash_parameter' has been initialized by spi_nor_init_params(). With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps', the new argument of spi_nor_scan(), spi_nor_setup() computes the best match between hardware caps supported by both the (Q)SPI memory and controller hence selecting the relevant settings for (Fast) Read and Page Program operations. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
2017-04-25 20:08:46 +00:00
switch (proto) {
case SNOR_PROTO_1_1_2:
if_type = IF_TYPE_DUAL;
break;
mtd: spi-nor: introduce SPI 1-2-2 and SPI 1-4-4 protocols This patch changes the prototype of spi_nor_scan(): its 3rd parameter is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor framework about the actual hardware capabilities supported by the SPI controller and its driver. Besides, this patch also introduces a new 'struct spi_nor_flash_parameter' telling the spi-nor framework about the hardware capabilities supported by the SPI flash memory and the associated settings required to use those hardware caps. Then, to improve the readability of spi_nor_scan(), the discovery of the memory settings and the memory initialization are now split into two dedicated functions. 1 - spi_nor_init_params() The spi_nor_init_params() function is responsible for initializing the 'struct spi_nor_flash_parameter'. Currently this structure is filled with legacy values but further patches will allow to override some parameter values dynamically, for instance by reading the JESD216 Serial Flash Discoverable Parameter (SFDP) tables from the SPI memory. The spi_nor_init_params() function only deals with the hardware capabilities of the SPI flash memory: especially it doesn't care about the hardware capabilities supported by the SPI controller. 2 - spi_nor_setup() The second function is called once the 'struct spi_nor_flash_parameter' has been initialized by spi_nor_init_params(). With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps', the new argument of spi_nor_scan(), spi_nor_setup() computes the best match between hardware caps supported by both the (Q)SPI memory and controller hence selecting the relevant settings for (Fast) Read and Page Program operations. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
2017-04-25 20:08:46 +00:00
case SNOR_PROTO_1_2_2:
if_type = IF_TYPE_DIO;
break;
case SNOR_PROTO_1_1_4:
if_type = IF_TYPE_QUAD;
break;
mtd: spi-nor: introduce SPI 1-2-2 and SPI 1-4-4 protocols This patch changes the prototype of spi_nor_scan(): its 3rd parameter is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor framework about the actual hardware capabilities supported by the SPI controller and its driver. Besides, this patch also introduces a new 'struct spi_nor_flash_parameter' telling the spi-nor framework about the hardware capabilities supported by the SPI flash memory and the associated settings required to use those hardware caps. Then, to improve the readability of spi_nor_scan(), the discovery of the memory settings and the memory initialization are now split into two dedicated functions. 1 - spi_nor_init_params() The spi_nor_init_params() function is responsible for initializing the 'struct spi_nor_flash_parameter'. Currently this structure is filled with legacy values but further patches will allow to override some parameter values dynamically, for instance by reading the JESD216 Serial Flash Discoverable Parameter (SFDP) tables from the SPI memory. The spi_nor_init_params() function only deals with the hardware capabilities of the SPI flash memory: especially it doesn't care about the hardware capabilities supported by the SPI controller. 2 - spi_nor_setup() The second function is called once the 'struct spi_nor_flash_parameter' has been initialized by spi_nor_init_params(). With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps', the new argument of spi_nor_scan(), spi_nor_setup() computes the best match between hardware caps supported by both the (Q)SPI memory and controller hence selecting the relevant settings for (Fast) Read and Page Program operations. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
2017-04-25 20:08:46 +00:00
case SNOR_PROTO_1_4_4:
if_type = IF_TYPE_QIO;
break;
case SNOR_PROTO_1_1_1:
default:
if_type = IF_TYPE_STD;
break;
}
return if_type;
}
static void hisi_spi_nor_init(struct hifmc_host *host)
{
u32 reg;
reg = TIMING_CFG_TCSH(CS_HOLD_TIME)
| TIMING_CFG_TCSS(CS_SETUP_TIME)
| TIMING_CFG_TSHSL(CS_DESELECT_TIME);
writel(reg, host->regbase + FMC_SPI_TIMING_CFG);
}
static int hisi_spi_nor_prep(struct spi_nor *nor, enum spi_nor_ops ops)
{
struct hifmc_priv *priv = nor->priv;
struct hifmc_host *host = priv->host;
int ret;
mutex_lock(&host->lock);
ret = clk_set_rate(host->clk, priv->clkrate);
if (ret)
goto out;
ret = clk_prepare_enable(host->clk);
if (ret)
goto out;
return 0;
out:
mutex_unlock(&host->lock);
return ret;
}
static void hisi_spi_nor_unprep(struct spi_nor *nor, enum spi_nor_ops ops)
{
struct hifmc_priv *priv = nor->priv;
struct hifmc_host *host = priv->host;
clk_disable_unprepare(host->clk);
mutex_unlock(&host->lock);
}
static int hisi_spi_nor_op_reg(struct spi_nor *nor,
u8 opcode, int len, u8 optype)
{
struct hifmc_priv *priv = nor->priv;
struct hifmc_host *host = priv->host;
u32 reg;
reg = FMC_CMD_CMD1(opcode);
writel(reg, host->regbase + FMC_CMD);
reg = FMC_DATA_NUM_CNT(len);
writel(reg, host->regbase + FMC_DATA_NUM);
reg = OP_CFG_FM_CS(priv->chipselect);
writel(reg, host->regbase + FMC_OP_CFG);
writel(0xff, host->regbase + FMC_INT_CLR);
reg = FMC_OP_CMD1_EN | FMC_OP_REG_OP_START | optype;
writel(reg, host->regbase + FMC_OP);
return wait_op_finish(host);
}
static int hisi_spi_nor_read_reg(struct spi_nor *nor, u8 opcode, u8 *buf,
int len)
{
struct hifmc_priv *priv = nor->priv;
struct hifmc_host *host = priv->host;
int ret;
ret = hisi_spi_nor_op_reg(nor, opcode, len, FMC_OP_READ_DATA_EN);
if (ret)
return ret;
memcpy_fromio(buf, host->iobase, len);
return 0;
}
static int hisi_spi_nor_write_reg(struct spi_nor *nor, u8 opcode,
u8 *buf, int len)
{
struct hifmc_priv *priv = nor->priv;
struct hifmc_host *host = priv->host;
if (len)
memcpy_toio(host->iobase, buf, len);
return hisi_spi_nor_op_reg(nor, opcode, len, FMC_OP_WRITE_DATA_EN);
}
static int hisi_spi_nor_dma_transfer(struct spi_nor *nor, loff_t start_off,
dma_addr_t dma_buf, size_t len, u8 op_type)
{
struct hifmc_priv *priv = nor->priv;
struct hifmc_host *host = priv->host;
u8 if_type = 0;
u32 reg;
reg = readl(host->regbase + FMC_CFG);
reg &= ~(FMC_CFG_OP_MODE_MASK | SPI_NOR_ADDR_MODE_MASK);
reg |= FMC_CFG_OP_MODE_NORMAL;
reg |= (nor->addr_width == 4) ? SPI_NOR_ADDR_MODE_4BYTES
: SPI_NOR_ADDR_MODE_3BYTES;
writel(reg, host->regbase + FMC_CFG);
writel(start_off, host->regbase + FMC_ADDRL);
writel(dma_buf, host->regbase + FMC_DMA_SADDR_D0);
writel(FMC_DMA_LEN_SET(len), host->regbase + FMC_DMA_LEN);
reg = OP_CFG_FM_CS(priv->chipselect);
mtd: spi-nor: introduce SPI 1-2-2 and SPI 1-4-4 protocols This patch changes the prototype of spi_nor_scan(): its 3rd parameter is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor framework about the actual hardware capabilities supported by the SPI controller and its driver. Besides, this patch also introduces a new 'struct spi_nor_flash_parameter' telling the spi-nor framework about the hardware capabilities supported by the SPI flash memory and the associated settings required to use those hardware caps. Then, to improve the readability of spi_nor_scan(), the discovery of the memory settings and the memory initialization are now split into two dedicated functions. 1 - spi_nor_init_params() The spi_nor_init_params() function is responsible for initializing the 'struct spi_nor_flash_parameter'. Currently this structure is filled with legacy values but further patches will allow to override some parameter values dynamically, for instance by reading the JESD216 Serial Flash Discoverable Parameter (SFDP) tables from the SPI memory. The spi_nor_init_params() function only deals with the hardware capabilities of the SPI flash memory: especially it doesn't care about the hardware capabilities supported by the SPI controller. 2 - spi_nor_setup() The second function is called once the 'struct spi_nor_flash_parameter' has been initialized by spi_nor_init_params(). With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps', the new argument of spi_nor_scan(), spi_nor_setup() computes the best match between hardware caps supported by both the (Q)SPI memory and controller hence selecting the relevant settings for (Fast) Read and Page Program operations. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
2017-04-25 20:08:46 +00:00
if (op_type == FMC_OP_READ)
if_type = get_if_type(nor->read_proto);
else
if_type = get_if_type(nor->write_proto);
reg |= OP_CFG_MEM_IF_TYPE(if_type);
if (op_type == FMC_OP_READ)
reg |= OP_CFG_DUMMY_NUM(nor->read_dummy >> 3);
writel(reg, host->regbase + FMC_OP_CFG);
writel(0xff, host->regbase + FMC_INT_CLR);
reg = OP_CTRL_RW_OP(op_type) | OP_CTRL_DMA_OP_READY;
reg |= (op_type == FMC_OP_READ)
? OP_CTRL_RD_OPCODE(nor->read_opcode)
: OP_CTRL_WR_OPCODE(nor->program_opcode);
writel(reg, host->regbase + FMC_OP_DMA);
return wait_op_finish(host);
}
static ssize_t hisi_spi_nor_read(struct spi_nor *nor, loff_t from, size_t len,
u_char *read_buf)
{
struct hifmc_priv *priv = nor->priv;
struct hifmc_host *host = priv->host;
size_t offset;
int ret;
for (offset = 0; offset < len; offset += HIFMC_DMA_MAX_LEN) {
size_t trans = min_t(size_t, HIFMC_DMA_MAX_LEN, len - offset);
ret = hisi_spi_nor_dma_transfer(nor,
from + offset, host->dma_buffer, trans, FMC_OP_READ);
if (ret) {
dev_warn(nor->dev, "DMA read timeout\n");
return ret;
}
memcpy(read_buf + offset, host->buffer, trans);
}
return len;
}
static ssize_t hisi_spi_nor_write(struct spi_nor *nor, loff_t to,
size_t len, const u_char *write_buf)
{
struct hifmc_priv *priv = nor->priv;
struct hifmc_host *host = priv->host;
size_t offset;
int ret;
for (offset = 0; offset < len; offset += HIFMC_DMA_MAX_LEN) {
size_t trans = min_t(size_t, HIFMC_DMA_MAX_LEN, len - offset);
memcpy(host->buffer, write_buf + offset, trans);
ret = hisi_spi_nor_dma_transfer(nor,
to + offset, host->dma_buffer, trans, FMC_OP_WRITE);
if (ret) {
dev_warn(nor->dev, "DMA write timeout\n");
return ret;
}
}
return len;
}
/**
* Get spi flash device information and register it as a mtd device.
*/
static int hisi_spi_nor_register(struct device_node *np,
struct hifmc_host *host)
{
mtd: spi-nor: introduce SPI 1-2-2 and SPI 1-4-4 protocols This patch changes the prototype of spi_nor_scan(): its 3rd parameter is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor framework about the actual hardware capabilities supported by the SPI controller and its driver. Besides, this patch also introduces a new 'struct spi_nor_flash_parameter' telling the spi-nor framework about the hardware capabilities supported by the SPI flash memory and the associated settings required to use those hardware caps. Then, to improve the readability of spi_nor_scan(), the discovery of the memory settings and the memory initialization are now split into two dedicated functions. 1 - spi_nor_init_params() The spi_nor_init_params() function is responsible for initializing the 'struct spi_nor_flash_parameter'. Currently this structure is filled with legacy values but further patches will allow to override some parameter values dynamically, for instance by reading the JESD216 Serial Flash Discoverable Parameter (SFDP) tables from the SPI memory. The spi_nor_init_params() function only deals with the hardware capabilities of the SPI flash memory: especially it doesn't care about the hardware capabilities supported by the SPI controller. 2 - spi_nor_setup() The second function is called once the 'struct spi_nor_flash_parameter' has been initialized by spi_nor_init_params(). With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps', the new argument of spi_nor_scan(), spi_nor_setup() computes the best match between hardware caps supported by both the (Q)SPI memory and controller hence selecting the relevant settings for (Fast) Read and Page Program operations. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
2017-04-25 20:08:46 +00:00
const struct spi_nor_hwcaps hwcaps = {
.mask = SNOR_HWCAPS_READ |
SNOR_HWCAPS_READ_FAST |
SNOR_HWCAPS_READ_1_1_2 |
SNOR_HWCAPS_READ_1_1_4 |
SNOR_HWCAPS_PP,
};
struct device *dev = host->dev;
struct spi_nor *nor;
struct hifmc_priv *priv;
struct mtd_info *mtd;
int ret;
nor = devm_kzalloc(dev, sizeof(*nor), GFP_KERNEL);
if (!nor)
return -ENOMEM;
nor->dev = dev;
spi_nor_set_flash_node(nor, np);
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
ret = of_property_read_u32(np, "reg", &priv->chipselect);
if (ret) {
dev_err(dev, "There's no reg property for %pOF\n",
np);
return ret;
}
ret = of_property_read_u32(np, "spi-max-frequency",
&priv->clkrate);
if (ret) {
dev_err(dev, "There's no spi-max-frequency property for %pOF\n",
np);
return ret;
}
priv->host = host;
nor->priv = priv;
nor->prepare = hisi_spi_nor_prep;
nor->unprepare = hisi_spi_nor_unprep;
nor->read_reg = hisi_spi_nor_read_reg;
nor->write_reg = hisi_spi_nor_write_reg;
nor->read = hisi_spi_nor_read;
nor->write = hisi_spi_nor_write;
nor->erase = NULL;
mtd: spi-nor: introduce SPI 1-2-2 and SPI 1-4-4 protocols This patch changes the prototype of spi_nor_scan(): its 3rd parameter is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor framework about the actual hardware capabilities supported by the SPI controller and its driver. Besides, this patch also introduces a new 'struct spi_nor_flash_parameter' telling the spi-nor framework about the hardware capabilities supported by the SPI flash memory and the associated settings required to use those hardware caps. Then, to improve the readability of spi_nor_scan(), the discovery of the memory settings and the memory initialization are now split into two dedicated functions. 1 - spi_nor_init_params() The spi_nor_init_params() function is responsible for initializing the 'struct spi_nor_flash_parameter'. Currently this structure is filled with legacy values but further patches will allow to override some parameter values dynamically, for instance by reading the JESD216 Serial Flash Discoverable Parameter (SFDP) tables from the SPI memory. The spi_nor_init_params() function only deals with the hardware capabilities of the SPI flash memory: especially it doesn't care about the hardware capabilities supported by the SPI controller. 2 - spi_nor_setup() The second function is called once the 'struct spi_nor_flash_parameter' has been initialized by spi_nor_init_params(). With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps', the new argument of spi_nor_scan(), spi_nor_setup() computes the best match between hardware caps supported by both the (Q)SPI memory and controller hence selecting the relevant settings for (Fast) Read and Page Program operations. Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
2017-04-25 20:08:46 +00:00
ret = spi_nor_scan(nor, NULL, &hwcaps);
if (ret)
return ret;
mtd = &nor->mtd;
mtd->name = np->name;
ret = mtd_device_register(mtd, NULL, 0);
if (ret)
return ret;
host->nor[host->num_chip] = nor;
host->num_chip++;
return 0;
}
static void hisi_spi_nor_unregister_all(struct hifmc_host *host)
{
int i;
for (i = 0; i < host->num_chip; i++)
mtd_device_unregister(&host->nor[i]->mtd);
}
static int hisi_spi_nor_register_all(struct hifmc_host *host)
{
struct device *dev = host->dev;
struct device_node *np;
int ret;
for_each_available_child_of_node(dev->of_node, np) {
ret = hisi_spi_nor_register(np, host);
if (ret)
goto fail;
if (host->num_chip == HIFMC_MAX_CHIP_NUM) {
dev_warn(dev, "Flash device number exceeds the maximum chipselect number\n");
break;
}
}
return 0;
fail:
hisi_spi_nor_unregister_all(host);
return ret;
}
static int hisi_spi_nor_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct resource *res;
struct hifmc_host *host;
int ret;
host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL);
if (!host)
return -ENOMEM;
platform_set_drvdata(pdev, host);
host->dev = dev;
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "control");
host->regbase = devm_ioremap_resource(dev, res);
if (IS_ERR(host->regbase))
return PTR_ERR(host->regbase);
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "memory");
host->iobase = devm_ioremap_resource(dev, res);
if (IS_ERR(host->iobase))
return PTR_ERR(host->iobase);
host->clk = devm_clk_get(dev, NULL);
if (IS_ERR(host->clk))
return PTR_ERR(host->clk);
ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
if (ret) {
dev_warn(dev, "Unable to set dma mask\n");
return ret;
}
host->buffer = dmam_alloc_coherent(dev, HIFMC_DMA_MAX_LEN,
&host->dma_buffer, GFP_KERNEL);
if (!host->buffer)
return -ENOMEM;
ret = clk_prepare_enable(host->clk);
if (ret)
return ret;
mutex_init(&host->lock);
hisi_spi_nor_init(host);
ret = hisi_spi_nor_register_all(host);
if (ret)
mutex_destroy(&host->lock);
clk_disable_unprepare(host->clk);
return ret;
}
static int hisi_spi_nor_remove(struct platform_device *pdev)
{
struct hifmc_host *host = platform_get_drvdata(pdev);
hisi_spi_nor_unregister_all(host);
mutex_destroy(&host->lock);
clk_disable_unprepare(host->clk);
return 0;
}
static const struct of_device_id hisi_spi_nor_dt_ids[] = {
{ .compatible = "hisilicon,fmc-spi-nor"},
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, hisi_spi_nor_dt_ids);
static struct platform_driver hisi_spi_nor_driver = {
.driver = {
.name = "hisi-sfc",
.of_match_table = hisi_spi_nor_dt_ids,
},
.probe = hisi_spi_nor_probe,
.remove = hisi_spi_nor_remove,
};
module_platform_driver(hisi_spi_nor_driver);
MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("HiSilicon SPI Nor Flash Controller Driver");