linux/drivers/gpio/gpiolib.c

4339 lines
116 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0
#include <linux/bitmap.h>
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/interrupt.h>
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
#include <linux/irq.h>
#include <linux/spinlock.h>
#include <linux/list.h>
gpio: sysfs interface This adds a simple sysfs interface for GPIOs. /sys/class/gpio /export ... asks the kernel to export a GPIO to userspace /unexport ... to return a GPIO to the kernel /gpioN ... for each exported GPIO #N /value ... always readable, writes fail for input GPIOs /direction ... r/w as: in, out (default low); write high, low /gpiochipN ... for each gpiochip; #N is its first GPIO /base ... (r/o) same as N /label ... (r/o) descriptive, not necessarily unique /ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1) GPIOs claimed by kernel code may be exported by its owner using a new gpio_export() call, which should be most useful for driver debugging. Such exports may optionally be done without a "direction" attribute. Userspace may ask to take over a GPIO by writing to a sysfs control file, helping to cope with incomplete board support or other "one-off" requirements that don't merit full kernel support: echo 23 > /sys/class/gpio/export ... will gpio_request(23, "sysfs") and gpio_export(23); use /sys/class/gpio/gpio-23/direction to (re)configure it, when that GPIO can be used as both input and output. echo 23 > /sys/class/gpio/unexport ... will gpio_free(23), when it was exported as above The extra D-space footprint is a few hundred bytes, except for the sysfs resources associated with each exported GPIO. The additional I-space footprint is about two thirds of the current size of gpiolib (!). Since no /dev node creation is involved, no "udev" support is needed. Related changes: * This adds a device pointer to "struct gpio_chip". When GPIO providers initialize that, sysfs gpio class devices become children of that device instead of being "virtual" devices. * The (few) gpio_chip providers which have such a device node have been updated. * Some gpio_chip drivers also needed to update their module "owner" field ... for which missing kerneldoc was added. * Some gpio_chips don't support input GPIOs. Those GPIOs are now flagged appropriately when the chip is registered. Based on previous patches, and discussion both on and off LKML. A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this merges to mainline. [akpm@linux-foundation.org: a few maintenance build fixes] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Cc: Greg KH <greg@kroah.com> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-25 08:46:07 +00:00
#include <linux/device.h>
#include <linux/err.h>
#include <linux/debugfs.h>
#include <linux/seq_file.h>
#include <linux/gpio.h>
#include <linux/idr.h>
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 08:04:11 +00:00
#include <linux/slab.h>
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node Modify struct acpi_dev_node to contain a pointer to struct acpi_device associated with the given device object (that is, its ACPI companion device) instead of an ACPI handle corresponding to it. Introduce two new macros for manipulating that pointer in a CONFIG_ACPI-safe way, ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the ACPI_HANDLE() macro to take the above changes into account. Drop the ACPI_HANDLE_SET() macro entirely and rework its users to use ACPI_COMPANION_SET() instead. For some of them who used to pass the result of acpi_get_child() directly to ACPI_HANDLE_SET() introduce a helper routine acpi_preset_companion() doing an equivalent thing. The main motivation for doing this is that there are things represented by struct acpi_device objects that don't have valid ACPI handles (so called fixed ACPI hardware features, such as power and sleep buttons) and we would like to create platform device objects for them and "glue" them to their ACPI companions in the usual way (which currently is impossible due to the lack of valid ACPI handles). However, there are more reasons why it may be useful. First, struct acpi_device pointers allow of much better type checking than void pointers which are ACPI handles, so it should be more difficult to write buggy code using modified struct acpi_dev_node and the new macros. Second, the change should help to reduce (over time) the number of places in which the result of ACPI_HANDLE() is passed to acpi_bus_get_device() in order to obtain a pointer to the struct acpi_device associated with the given "physical" device, because now that pointer is returned by ACPI_COMPANION() directly. Finally, the change should make it easier to write generic code that will build both for CONFIG_ACPI set and unset without adding explicit compiler directives to it. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
2013-11-11 21:41:56 +00:00
#include <linux/acpi.h>
#include <linux/gpio/driver.h>
#include <linux/gpio/machine.h>
#include <linux/pinctrl/consumer.h>
gpio: add a userspace chardev ABI for GPIOs A new chardev that is to be used for userspace GPIO access is added in this patch. It is intended to gradually replace the horribly broken sysfs ABI. Using a chardev has many upsides: - All operations are per-gpiochip, which is the actual device underlying the GPIOs, making us tie in to the kernel device model properly. - Hotpluggable GPIO controllers can come and go, as this kind of problem has been know to userspace for character devices since ages, and if a gpiochip handle is held in userspace we know we will break something, whereas the sysfs is stateless. - The one-value-per-file rule of sysfs is really hard to maintain when you want to twist more than one knob at a time, for example have in-kernel APIs to switch several GPIO lines at the same time, and this will be possible to do with a single ioctl() from userspace, saving a lot of context switching. We also need to add a new bus type for GPIO. This is necessary for example for userspace coldplug, where sysfs is traversed to find the boot-time device nodes and create the character devices in /dev. This new chardev ABI is *non* *optional* and can be counted on to be present in the future, emphasizing the preference of this ABI. The ABI only implements one single ioctl() to get the name and number of GPIO lines of a chip. Even this is debatable: see it as a minimal example for review. This ABI shall be ruthlessly reviewed and etched in stone. The old /sys/class/gpio is still optional to compile in, but will be deprecated. Unique device IDs are created using IDR, which is overkill and insanely scalable, but also well tested. Cc: Johan Hovold <johan@kernel.org> Cc: Michael Welling <mwelling@ieee.org> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 13:29:53 +00:00
#include <linux/fs.h>
#include <linux/compat.h>
gpio: GPIO_GET_LINE{HANDLE,EVENT}_IOCTL: Fix file descriptor leak When allocating a new line handle or event a file is allocated that it is associated to. The file is attached to a file descriptor of the current process and the file descriptor is returned to userspace using copy_to_user(). If this copy operation fails the line handle or event allocation is aborted, all acquired resources are freed and an error is returned. But the file struct is not freed and left attached to the userspace application and even though the file descriptor number was not copied it is trivial to guess. If a userspace application performs a IOCTL on such a left over file descriptor it will trigger a use-after-free and if the file descriptor is closed (latest when the application exits) a double-free is triggered. anon_inode_getfd() performs 3 tasks, allocate a file struct, allocate a file descriptor for the current process and install the file struct in the file descriptor. As soon as the file struct is installed in the file descriptor it is accessible by userspace (even if the IOCTL itself hasn't completed yet), this means uninstalling the fd on the error path is not an option, since userspace might already got a reference to the file. Instead anon_inode_getfd() needs to be broken into its individual steps. The allocation of the file struct and file descriptor is done first, then the copy_to_user() is executed and only if it succeeds the file is installed. Since the file struct is reference counted it can not be just freed, but its reference needs to be dropped, which will also call the release() callback, which will free the state attached to the file. So in this case the normal error cleanup path should not be taken. Cc: stable@vger.kernel.org Fixes: d932cd49182f ("gpio: free handles in fringe cases") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-24 11:59:15 +00:00
#include <linux/file.h>
gpio: add a userspace chardev ABI for GPIOs A new chardev that is to be used for userspace GPIO access is added in this patch. It is intended to gradually replace the horribly broken sysfs ABI. Using a chardev has many upsides: - All operations are per-gpiochip, which is the actual device underlying the GPIOs, making us tie in to the kernel device model properly. - Hotpluggable GPIO controllers can come and go, as this kind of problem has been know to userspace for character devices since ages, and if a gpiochip handle is held in userspace we know we will break something, whereas the sysfs is stateless. - The one-value-per-file rule of sysfs is really hard to maintain when you want to twist more than one knob at a time, for example have in-kernel APIs to switch several GPIO lines at the same time, and this will be possible to do with a single ioctl() from userspace, saving a lot of context switching. We also need to add a new bus type for GPIO. This is necessary for example for userspace coldplug, where sysfs is traversed to find the boot-time device nodes and create the character devices in /dev. This new chardev ABI is *non* *optional* and can be counted on to be present in the future, emphasizing the preference of this ABI. The ABI only implements one single ioctl() to get the name and number of GPIO lines of a chip. Even this is debatable: see it as a minimal example for review. This ABI shall be ruthlessly reviewed and etched in stone. The old /sys/class/gpio is still optional to compile in, but will be deprecated. Unique device IDs are created using IDR, which is overkill and insanely scalable, but also well tested. Cc: Johan Hovold <johan@kernel.org> Cc: Michael Welling <mwelling@ieee.org> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 13:29:53 +00:00
#include <uapi/linux/gpio.h>
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
#include "gpiolib.h"
#include "gpiolib-of.h"
#include "gpiolib-acpi.h"
#include "gpiolib-cdev.h"
#include "gpiolib-sysfs.h"
#define CREATE_TRACE_POINTS
#include <trace/events/gpio.h>
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/* Implementation infrastructure for GPIO interfaces.
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*
* The GPIO programming interface allows for inlining speed-critical
* get/set operations for common cases, so that access to SOC-integrated
* GPIOs can sometimes cost only an instruction or two per bit.
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*/
/* When debugging, extend minimal trust to callers and platform code.
* Also emit diagnostic messages that may help initial bringup, when
* board setup or driver bugs are most common.
*
* Otherwise, minimize overhead in what may be bitbanging codepaths.
*/
#ifdef DEBUG
#define extra_checks 1
#else
#define extra_checks 0
#endif
/* Device and char device-related information */
static DEFINE_IDA(gpio_ida);
gpio: add a userspace chardev ABI for GPIOs A new chardev that is to be used for userspace GPIO access is added in this patch. It is intended to gradually replace the horribly broken sysfs ABI. Using a chardev has many upsides: - All operations are per-gpiochip, which is the actual device underlying the GPIOs, making us tie in to the kernel device model properly. - Hotpluggable GPIO controllers can come and go, as this kind of problem has been know to userspace for character devices since ages, and if a gpiochip handle is held in userspace we know we will break something, whereas the sysfs is stateless. - The one-value-per-file rule of sysfs is really hard to maintain when you want to twist more than one knob at a time, for example have in-kernel APIs to switch several GPIO lines at the same time, and this will be possible to do with a single ioctl() from userspace, saving a lot of context switching. We also need to add a new bus type for GPIO. This is necessary for example for userspace coldplug, where sysfs is traversed to find the boot-time device nodes and create the character devices in /dev. This new chardev ABI is *non* *optional* and can be counted on to be present in the future, emphasizing the preference of this ABI. The ABI only implements one single ioctl() to get the name and number of GPIO lines of a chip. Even this is debatable: see it as a minimal example for review. This ABI shall be ruthlessly reviewed and etched in stone. The old /sys/class/gpio is still optional to compile in, but will be deprecated. Unique device IDs are created using IDR, which is overkill and insanely scalable, but also well tested. Cc: Johan Hovold <johan@kernel.org> Cc: Michael Welling <mwelling@ieee.org> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 13:29:53 +00:00
static dev_t gpio_devt;
#define GPIO_DEV_MAX 256 /* 256 GPIO chip devices supported */
static struct bus_type gpio_bus_type = {
.name = "gpio",
};
/*
* Number of GPIOs to use for the fast path in set array
*/
#define FASTPATH_NGPIO CONFIG_GPIOLIB_FASTPATH_LIMIT
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/* gpio_lock prevents conflicts during gpio_desc[] table updates.
* While any GPIO is requested, its gpio_chip is not removable;
* each GPIO's "requested" flag serves as a lock and refcount.
*/
DEFINE_SPINLOCK(gpio_lock);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
static DEFINE_MUTEX(gpio_lookup_lock);
static LIST_HEAD(gpio_lookup_list);
LIST_HEAD(gpio_devices);
static DEFINE_MUTEX(gpio_machine_hogs_mutex);
static LIST_HEAD(gpio_machine_hogs);
static void gpiochip_free_hogs(struct gpio_chip *gc);
static int gpiochip_add_irqchip(struct gpio_chip *gc,
struct lock_class_key *lock_key,
struct lock_class_key *request_key);
static void gpiochip_irqchip_remove(struct gpio_chip *gc);
static int gpiochip_irqchip_init_hw(struct gpio_chip *gc);
static int gpiochip_irqchip_init_valid_mask(struct gpio_chip *gc);
static void gpiochip_irqchip_free_valid_mask(struct gpio_chip *gc);
static bool gpiolib_initialized;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
static inline void desc_set_label(struct gpio_desc *d, const char *label)
{
d->label = label;
}
/**
* gpio_to_desc - Convert a GPIO number to its descriptor
* @gpio: global GPIO number
*
* Returns:
* The GPIO descriptor associated with the given GPIO, or %NULL if no GPIO
* with the given number exists in the system.
*/
struct gpio_desc *gpio_to_desc(unsigned gpio)
{
struct gpio_device *gdev;
unsigned long flags;
spin_lock_irqsave(&gpio_lock, flags);
list_for_each_entry(gdev, &gpio_devices, list) {
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
if (gdev->base <= gpio &&
gdev->base + gdev->ngpio > gpio) {
spin_unlock_irqrestore(&gpio_lock, flags);
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
return &gdev->descs[gpio - gdev->base];
}
}
spin_unlock_irqrestore(&gpio_lock, flags);
if (!gpio_is_valid(gpio))
WARN(1, "invalid GPIO %d\n", gpio);
return NULL;
}
EXPORT_SYMBOL_GPL(gpio_to_desc);
/**
* gpiochip_get_desc - get the GPIO descriptor corresponding to the given
* hardware number for this chip
* @gc: GPIO chip
* @hwnum: hardware number of the GPIO for this chip
*
* Returns:
* A pointer to the GPIO descriptor or ``ERR_PTR(-EINVAL)`` if no GPIO exists
* in the given chip for the specified hardware number.
*/
struct gpio_desc *gpiochip_get_desc(struct gpio_chip *gc,
unsigned int hwnum)
{
struct gpio_device *gdev = gc->gpiodev;
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
if (hwnum >= gdev->ngpio)
return ERR_PTR(-EINVAL);
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
return &gdev->descs[hwnum];
}
EXPORT_SYMBOL_GPL(gpiochip_get_desc);
/**
* desc_to_gpio - convert a GPIO descriptor to the integer namespace
* @desc: GPIO descriptor
*
* This should disappear in the future but is needed since we still
* use GPIO numbers for error messages and sysfs nodes.
*
* Returns:
* The global GPIO number for the GPIO specified by its descriptor.
*/
int desc_to_gpio(const struct gpio_desc *desc)
{
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
return desc->gdev->base + (desc - &desc->gdev->descs[0]);
}
EXPORT_SYMBOL_GPL(desc_to_gpio);
/**
* gpiod_to_chip - Return the GPIO chip to which a GPIO descriptor belongs
* @desc: descriptor to return the chip of
*/
struct gpio_chip *gpiod_to_chip(const struct gpio_desc *desc)
{
if (!desc || !desc->gdev)
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
return NULL;
return desc->gdev->chip;
}
EXPORT_SYMBOL_GPL(gpiod_to_chip);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/* dynamic allocation of GPIOs, e.g. on a hotplugged device */
static int gpiochip_find_base(int ngpio)
{
struct gpio_device *gdev;
int base = ARCH_NR_GPIOS - ngpio;
list_for_each_entry_reverse(gdev, &gpio_devices, list) {
/* found a free space? */
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
if (gdev->base + gdev->ngpio <= base)
break;
else
/* nope, check the space right before the chip */
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
base = gdev->base - ngpio;
}
if (gpio_is_valid(base)) {
pr_debug("%s: found new base at %d\n", __func__, base);
return base;
} else {
pr_err("%s: cannot find free range\n", __func__);
return -ENOSPC;
}
}
/**
* gpiod_get_direction - return the current direction of a GPIO
* @desc: GPIO to get the direction of
*
* Returns 0 for output, 1 for input, or an error code in case of error.
*
* This function may sleep if gpiod_cansleep() is true.
*/
int gpiod_get_direction(struct gpio_desc *desc)
{
struct gpio_chip *gc;
unsigned int offset;
int ret;
gc = gpiod_to_chip(desc);
offset = gpio_chip_hwgpio(desc);
/*
* Open drain emulation using input mode may incorrectly report
* input here, fix that up.
*/
if (test_bit(FLAG_OPEN_DRAIN, &desc->flags) &&
test_bit(FLAG_IS_OUT, &desc->flags))
return 0;
if (!gc->get_direction)
return -ENOTSUPP;
ret = gc->get_direction(gc, offset);
if (ret < 0)
return ret;
/* GPIOF_DIR_IN or other positive, otherwise GPIOF_DIR_OUT */
if (ret > 0)
ret = 1;
assign_bit(FLAG_IS_OUT, &desc->flags, !ret);
return ret;
}
EXPORT_SYMBOL_GPL(gpiod_get_direction);
/*
* Add a new chip to the global chips list, keeping the list of chips sorted
* by range(means [base, base + ngpio - 1]) order.
*
* Return -EBUSY if the new chip overlaps with some other chip's integer
* space.
*/
static int gpiodev_add_to_list(struct gpio_device *gdev)
{
struct gpio_device *prev, *next;
if (list_empty(&gpio_devices)) {
/* initial entry in list */
list_add_tail(&gdev->list, &gpio_devices);
return 0;
}
next = list_entry(gpio_devices.next, struct gpio_device, list);
if (gdev->base + gdev->ngpio <= next->base) {
/* add before first entry */
list_add(&gdev->list, &gpio_devices);
return 0;
}
prev = list_entry(gpio_devices.prev, struct gpio_device, list);
if (prev->base + prev->ngpio <= gdev->base) {
/* add behind last entry */
list_add_tail(&gdev->list, &gpio_devices);
return 0;
}
list_for_each_entry_safe(prev, next, &gpio_devices, list) {
/* at the end of the list */
if (&next->list == &gpio_devices)
break;
/* add between prev and next */
if (prev->base + prev->ngpio <= gdev->base
&& gdev->base + gdev->ngpio <= next->base) {
list_add(&gdev->list, &prev->list);
return 0;
}
}
dev_err(&gdev->dev, "GPIO integer space overlap, cannot add chip\n");
return -EBUSY;
}
/*
* Convert a GPIO name to its descriptor
* Note that there is no guarantee that GPIO names are globally unique!
* Hence this function will return, if it exists, a reference to the first GPIO
* line found that matches the given name.
*/
static struct gpio_desc *gpio_name_to_desc(const char * const name)
{
struct gpio_device *gdev;
unsigned long flags;
if (!name)
return NULL;
spin_lock_irqsave(&gpio_lock, flags);
list_for_each_entry(gdev, &gpio_devices, list) {
int i;
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
for (i = 0; i != gdev->ngpio; ++i) {
struct gpio_desc *desc = &gdev->descs[i];
if (!desc->name)
continue;
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
if (!strcmp(desc->name, name)) {
spin_unlock_irqrestore(&gpio_lock, flags);
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
return desc;
}
}
}
spin_unlock_irqrestore(&gpio_lock, flags);
return NULL;
}
/*
* Take the names from gc->names and assign them to their GPIO descriptors.
* Warn if a name is already used for a GPIO line on a different GPIO chip.
*
* Note that:
* 1. Non-unique names are still accepted,
* 2. Name collisions within the same GPIO chip are not reported.
*/
static int gpiochip_set_desc_names(struct gpio_chip *gc)
{
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
struct gpio_device *gdev = gc->gpiodev;
int i;
/* First check all names if they are unique */
for (i = 0; i != gc->ngpio; ++i) {
struct gpio_desc *gpio;
gpio = gpio_name_to_desc(gc->names[i]);
if (gpio)
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
dev_warn(&gdev->dev,
"Detected name collision for GPIO name '%s'\n",
gc->names[i]);
}
/* Then add all names to the GPIO descriptors */
for (i = 0; i != gc->ngpio; ++i)
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
gdev->descs[i].name = gc->names[i];
return 0;
}
/*
* devprop_gpiochip_set_names - Set GPIO line names using device properties
* @chip: GPIO chip whose lines should be named, if possible
*
* Looks for device property "gpio-line-names" and if it exists assigns
* GPIO line names for the chip. The memory allocated for the assigned
* names belong to the underlying software node and should not be released
* by the caller.
*/
static int devprop_gpiochip_set_names(struct gpio_chip *chip)
{
struct gpio_device *gdev = chip->gpiodev;
struct device *dev = chip->parent;
const char **names;
int ret, i;
int count;
/* GPIO chip may not have a parent device whose properties we inspect. */
if (!dev)
return 0;
count = device_property_string_array_count(dev, "gpio-line-names");
if (count < 0)
return 0;
if (count > gdev->ngpio) {
dev_warn(&gdev->dev, "gpio-line-names is length %d but should be at most length %d",
count, gdev->ngpio);
count = gdev->ngpio;
}
names = kcalloc(count, sizeof(*names), GFP_KERNEL);
if (!names)
return -ENOMEM;
ret = device_property_read_string_array(dev, "gpio-line-names",
names, count);
if (ret < 0) {
dev_warn(&gdev->dev, "failed to read GPIO line names\n");
kfree(names);
return ret;
}
for (i = 0; i < count; i++)
gdev->descs[i].name = names[i];
kfree(names);
return 0;
}
static unsigned long *gpiochip_allocate_mask(struct gpio_chip *gc)
{
unsigned long *p;
p = bitmap_alloc(gc->ngpio, GFP_KERNEL);
if (!p)
return NULL;
/* Assume by default all GPIOs are valid */
bitmap_fill(p, gc->ngpio);
return p;
}
static int gpiochip_alloc_valid_mask(struct gpio_chip *gc)
{
if (!(of_gpio_need_valid_mask(gc) || gc->init_valid_mask))
return 0;
gc->valid_mask = gpiochip_allocate_mask(gc);
if (!gc->valid_mask)
return -ENOMEM;
return 0;
}
static int gpiochip_init_valid_mask(struct gpio_chip *gc)
{
if (gc->init_valid_mask)
return gc->init_valid_mask(gc,
gc->valid_mask,
gc->ngpio);
return 0;
}
static void gpiochip_free_valid_mask(struct gpio_chip *gc)
{
bitmap_free(gc->valid_mask);
gc->valid_mask = NULL;
}
static int gpiochip_add_pin_ranges(struct gpio_chip *gc)
{
if (gc->add_pin_ranges)
return gc->add_pin_ranges(gc);
return 0;
}
bool gpiochip_line_is_valid(const struct gpio_chip *gc,
unsigned int offset)
{
/* No mask means all valid */
if (likely(!gc->valid_mask))
return true;
return test_bit(offset, gc->valid_mask);
}
EXPORT_SYMBOL_GPL(gpiochip_line_is_valid);
static void gpiodevice_release(struct device *dev)
{
struct gpio_device *gdev = dev_get_drvdata(dev);
list_del(&gdev->list);
ida_free(&gpio_ida, gdev->id);
kfree_const(gdev->label);
kfree(gdev->descs);
kfree(gdev);
}
#ifdef CONFIG_GPIO_CDEV
#define gcdev_register(gdev, devt) gpiolib_cdev_register((gdev), (devt))
#define gcdev_unregister(gdev) gpiolib_cdev_unregister((gdev))
#else
/*
* gpiolib_cdev_register() indirectly calls device_add(), which is still
* required even when cdev is not selected.
*/
#define gcdev_register(gdev, devt) device_add(&(gdev)->dev)
#define gcdev_unregister(gdev) device_del(&(gdev)->dev)
#endif
static int gpiochip_setup_dev(struct gpio_device *gdev)
{
int ret;
ret = gcdev_register(gdev, gpio_devt);
if (ret)
return ret;
ret = gpiochip_sysfs_register(gdev);
if (ret)
goto err_remove_device;
/* From this point, the .release() function cleans up gpio_device */
gdev->dev.release = gpiodevice_release;
dev_dbg(&gdev->dev, "registered GPIOs %d to %d on %s\n", gdev->base,
gdev->base + gdev->ngpio - 1, gdev->chip->label ? : "generic");
return 0;
err_remove_device:
gcdev_unregister(gdev);
return ret;
}
static void gpiochip_machine_hog(struct gpio_chip *gc, struct gpiod_hog *hog)
{
struct gpio_desc *desc;
int rv;
desc = gpiochip_get_desc(gc, hog->chip_hwnum);
if (IS_ERR(desc)) {
chip_err(gc, "%s: unable to get GPIO desc: %ld\n", __func__,
PTR_ERR(desc));
return;
}
if (test_bit(FLAG_IS_HOGGED, &desc->flags))
return;
rv = gpiod_hog(desc, hog->line_name, hog->lflags, hog->dflags);
if (rv)
gpiod_err(desc, "%s: unable to hog GPIO line (%s:%u): %d\n",
__func__, gc->label, hog->chip_hwnum, rv);
}
static void machine_gpiochip_add(struct gpio_chip *gc)
{
struct gpiod_hog *hog;
mutex_lock(&gpio_machine_hogs_mutex);
list_for_each_entry(hog, &gpio_machine_hogs, list) {
if (!strcmp(gc->label, hog->chip_label))
gpiochip_machine_hog(gc, hog);
}
mutex_unlock(&gpio_machine_hogs_mutex);
}
static void gpiochip_setup_devs(void)
{
struct gpio_device *gdev;
int ret;
list_for_each_entry(gdev, &gpio_devices, list) {
ret = gpiochip_setup_dev(gdev);
if (ret)
dev_err(&gdev->dev,
"Failed to initialize gpio device (%d)\n", ret);
}
}
int gpiochip_add_data_with_key(struct gpio_chip *gc, void *data,
struct lock_class_key *lock_key,
struct lock_class_key *request_key)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
unsigned long flags;
int ret = 0;
unsigned i;
int base = gc->base;
struct gpio_device *gdev;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/*
* First: allocate and populate the internal stat container, and
* set up the struct device.
*/
gdev = kzalloc(sizeof(*gdev), GFP_KERNEL);
if (!gdev)
return -ENOMEM;
gpio: add a userspace chardev ABI for GPIOs A new chardev that is to be used for userspace GPIO access is added in this patch. It is intended to gradually replace the horribly broken sysfs ABI. Using a chardev has many upsides: - All operations are per-gpiochip, which is the actual device underlying the GPIOs, making us tie in to the kernel device model properly. - Hotpluggable GPIO controllers can come and go, as this kind of problem has been know to userspace for character devices since ages, and if a gpiochip handle is held in userspace we know we will break something, whereas the sysfs is stateless. - The one-value-per-file rule of sysfs is really hard to maintain when you want to twist more than one knob at a time, for example have in-kernel APIs to switch several GPIO lines at the same time, and this will be possible to do with a single ioctl() from userspace, saving a lot of context switching. We also need to add a new bus type for GPIO. This is necessary for example for userspace coldplug, where sysfs is traversed to find the boot-time device nodes and create the character devices in /dev. This new chardev ABI is *non* *optional* and can be counted on to be present in the future, emphasizing the preference of this ABI. The ABI only implements one single ioctl() to get the name and number of GPIO lines of a chip. Even this is debatable: see it as a minimal example for review. This ABI shall be ruthlessly reviewed and etched in stone. The old /sys/class/gpio is still optional to compile in, but will be deprecated. Unique device IDs are created using IDR, which is overkill and insanely scalable, but also well tested. Cc: Johan Hovold <johan@kernel.org> Cc: Michael Welling <mwelling@ieee.org> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 13:29:53 +00:00
gdev->dev.bus = &gpio_bus_type;
gdev->chip = gc;
gc->gpiodev = gdev;
if (gc->parent) {
gdev->dev.parent = gc->parent;
gdev->dev.of_node = gc->parent->of_node;
}
#ifdef CONFIG_OF_GPIO
/* If the gpiochip has an assigned OF node this takes precedence */
if (gc->of_node)
gdev->dev.of_node = gc->of_node;
else
gc->of_node = gdev->dev.of_node;
#endif
gdev->id = ida_alloc(&gpio_ida, GFP_KERNEL);
if (gdev->id < 0) {
ret = gdev->id;
goto err_free_gdev;
}
dev_set_name(&gdev->dev, GPIOCHIP_NAME "%d", gdev->id);
device_initialize(&gdev->dev);
dev_set_drvdata(&gdev->dev, gdev);
if (gc->parent && gc->parent->driver)
gdev->owner = gc->parent->driver->owner;
else if (gc->owner)
/* TODO: remove chip->owner */
gdev->owner = gc->owner;
else
gdev->owner = THIS_MODULE;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
gdev->descs = kcalloc(gc->ngpio, sizeof(gdev->descs[0]), GFP_KERNEL);
if (!gdev->descs) {
ret = -ENOMEM;
goto err_free_ida;
}
if (gc->ngpio == 0) {
chip_err(gc, "tried to insert a GPIO chip with zero lines\n");
ret = -EINVAL;
goto err_free_descs;
}
if (gc->ngpio > FASTPATH_NGPIO)
chip_warn(gc, "line cnt %u is greater than fast path cnt %u\n",
gc->ngpio, FASTPATH_NGPIO);
gdev->label = kstrdup_const(gc->label ?: "unknown", GFP_KERNEL);
if (!gdev->label) {
ret = -ENOMEM;
goto err_free_descs;
}
gdev->ngpio = gc->ngpio;
gdev->data = data;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
spin_lock_irqsave(&gpio_lock, flags);
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
/*
* TODO: this allocates a Linux GPIO number base in the global
* GPIO numberspace for this chip. In the long run we want to
* get *rid* of this numberspace and use only descriptors, but
* it may be a pipe dream. It will not happen before we get rid
* of the sysfs interface anyways.
*/
if (base < 0) {
base = gpiochip_find_base(gc->ngpio);
if (base < 0) {
ret = base;
spin_unlock_irqrestore(&gpio_lock, flags);
goto err_free_label;
}
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
/*
* TODO: it should not be necessary to reflect the assigned
* base outside of the GPIO subsystem. Go over drivers and
* see if anyone makes use of this, else drop this and assign
* a poison instead.
*/
gc->base = base;
}
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
gdev->base = base;
ret = gpiodev_add_to_list(gdev);
if (ret) {
spin_unlock_irqrestore(&gpio_lock, flags);
goto err_free_label;
}
for (i = 0; i < gc->ngpio; i++)
gdev->descs[i].gdev = gdev;
spin_unlock_irqrestore(&gpio_lock, flags);
BLOCKING_INIT_NOTIFIER_HEAD(&gdev->notifier);
#ifdef CONFIG_PINCTRL
INIT_LIST_HEAD(&gdev->pin_ranges);
#endif
if (gc->names)
ret = gpiochip_set_desc_names(gc);
else
ret = devprop_gpiochip_set_names(gc);
if (ret)
goto err_remove_from_list;
ret = gpiochip_alloc_valid_mask(gc);
if (ret)
goto err_remove_from_list;
ret = of_gpiochip_add(gc);
if (ret)
goto err_free_gpiochip_mask;
ret = gpiochip_init_valid_mask(gc);
if (ret)
gpio: Fix gpiochip_add_data_with_key() error path The err_remove_chip block is too coarse, and may perform cleanup that must not be done. E.g. if of_gpiochip_add() fails, of_gpiochip_remove() is still called, causing: OF: ERROR: Bad of_node_put() on /soc/gpio@e6050000 CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.1.0-rc2-koelsch+ #407 Hardware name: Generic R-Car Gen2 (Flattened Device Tree) Workqueue: events deferred_probe_work_func [<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14) [<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c) [<c07c1224>] (dump_stack) from [<c07c5a80>] (kobject_put+0x94/0xbc) [<c07c5a80>] (kobject_put) from [<c0470420>] (gpiochip_add_data_with_key+0x8d8/0xa3c) [<c0470420>] (gpiochip_add_data_with_key) from [<c0473738>] (gpio_rcar_probe+0x1d4/0x314) [<c0473738>] (gpio_rcar_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94) and later, if a GPIO consumer tries to use a GPIO from a failed controller: WARNING: CPU: 0 PID: 1 at lib/refcount.c:156 kobject_get+0x38/0x4c refcount_t: increment on 0; use-after-free. Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.1.0-rc2-koelsch+ #407 Hardware name: Generic R-Car Gen2 (Flattened Device Tree) [<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14) [<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c) [<c07c1224>] (dump_stack) from [<c0221580>] (__warn+0xd0/0xec) [<c0221580>] (__warn) from [<c02215e0>] (warn_slowpath_fmt+0x44/0x6c) [<c02215e0>] (warn_slowpath_fmt) from [<c07c58fc>] (kobject_get+0x38/0x4c) [<c07c58fc>] (kobject_get) from [<c068b3ec>] (of_node_get+0x14/0x1c) [<c068b3ec>] (of_node_get) from [<c0686f24>] (of_find_node_by_phandle+0xc0/0xf0) [<c0686f24>] (of_find_node_by_phandle) from [<c0686fbc>] (of_phandle_iterator_next+0x68/0x154) [<c0686fbc>] (of_phandle_iterator_next) from [<c0687fe4>] (__of_parse_phandle_with_args+0x40/0xd0) [<c0687fe4>] (__of_parse_phandle_with_args) from [<c0688204>] (of_parse_phandle_with_args_map+0x100/0x3ac) [<c0688204>] (of_parse_phandle_with_args_map) from [<c0471240>] (of_get_named_gpiod_flags+0x38/0x380) [<c0471240>] (of_get_named_gpiod_flags) from [<c046f864>] (gpiod_get_from_of_node+0x24/0xd8) [<c046f864>] (gpiod_get_from_of_node) from [<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child+0xa0/0x144) [<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child) from [<c05f425c>] (gpio_keys_probe+0x418/0x7bc) [<c05f425c>] (gpio_keys_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94) Fix this by splitting the cleanup block, and adding a missing call to gpiochip_irqchip_remove(). Fixes: 28355f81969962cf ("gpio: defer probe if pinctrl cannot be found") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-04-24 13:59:33 +00:00
goto err_remove_of_chip;
for (i = 0; i < gc->ngpio; i++) {
struct gpio_desc *desc = &gdev->descs[i];
if (gc->get_direction && gpiochip_line_is_valid(gc, i)) {
assign_bit(FLAG_IS_OUT,
&desc->flags, !gc->get_direction(gc, i));
} else {
assign_bit(FLAG_IS_OUT,
&desc->flags, !gc->direction_input);
}
}
ret = gpiochip_add_pin_ranges(gc);
if (ret)
goto err_remove_of_chip;
acpi_gpiochip_add(gc);
machine_gpiochip_add(gc);
ret = gpiochip_irqchip_init_valid_mask(gc);
if (ret)
goto err_remove_acpi_chip;
ret = gpiochip_irqchip_init_hw(gc);
if (ret)
goto err_remove_acpi_chip;
ret = gpiochip_add_irqchip(gc, lock_key, request_key);
if (ret)
goto err_remove_irqchip_mask;
gpio: add a userspace chardev ABI for GPIOs A new chardev that is to be used for userspace GPIO access is added in this patch. It is intended to gradually replace the horribly broken sysfs ABI. Using a chardev has many upsides: - All operations are per-gpiochip, which is the actual device underlying the GPIOs, making us tie in to the kernel device model properly. - Hotpluggable GPIO controllers can come and go, as this kind of problem has been know to userspace for character devices since ages, and if a gpiochip handle is held in userspace we know we will break something, whereas the sysfs is stateless. - The one-value-per-file rule of sysfs is really hard to maintain when you want to twist more than one knob at a time, for example have in-kernel APIs to switch several GPIO lines at the same time, and this will be possible to do with a single ioctl() from userspace, saving a lot of context switching. We also need to add a new bus type for GPIO. This is necessary for example for userspace coldplug, where sysfs is traversed to find the boot-time device nodes and create the character devices in /dev. This new chardev ABI is *non* *optional* and can be counted on to be present in the future, emphasizing the preference of this ABI. The ABI only implements one single ioctl() to get the name and number of GPIO lines of a chip. Even this is debatable: see it as a minimal example for review. This ABI shall be ruthlessly reviewed and etched in stone. The old /sys/class/gpio is still optional to compile in, but will be deprecated. Unique device IDs are created using IDR, which is overkill and insanely scalable, but also well tested. Cc: Johan Hovold <johan@kernel.org> Cc: Michael Welling <mwelling@ieee.org> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 13:29:53 +00:00
/*
* By first adding the chardev, and then adding the device,
* we get a device node entry in sysfs under
* /sys/bus/gpio/devices/gpiochipN/dev that can be used for
* coldplug of device nodes and other udev business.
* We can do this only if gpiolib has been initialized.
* Otherwise, defer until later.
gpio: add a userspace chardev ABI for GPIOs A new chardev that is to be used for userspace GPIO access is added in this patch. It is intended to gradually replace the horribly broken sysfs ABI. Using a chardev has many upsides: - All operations are per-gpiochip, which is the actual device underlying the GPIOs, making us tie in to the kernel device model properly. - Hotpluggable GPIO controllers can come and go, as this kind of problem has been know to userspace for character devices since ages, and if a gpiochip handle is held in userspace we know we will break something, whereas the sysfs is stateless. - The one-value-per-file rule of sysfs is really hard to maintain when you want to twist more than one knob at a time, for example have in-kernel APIs to switch several GPIO lines at the same time, and this will be possible to do with a single ioctl() from userspace, saving a lot of context switching. We also need to add a new bus type for GPIO. This is necessary for example for userspace coldplug, where sysfs is traversed to find the boot-time device nodes and create the character devices in /dev. This new chardev ABI is *non* *optional* and can be counted on to be present in the future, emphasizing the preference of this ABI. The ABI only implements one single ioctl() to get the name and number of GPIO lines of a chip. Even this is debatable: see it as a minimal example for review. This ABI shall be ruthlessly reviewed and etched in stone. The old /sys/class/gpio is still optional to compile in, but will be deprecated. Unique device IDs are created using IDR, which is overkill and insanely scalable, but also well tested. Cc: Johan Hovold <johan@kernel.org> Cc: Michael Welling <mwelling@ieee.org> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 13:29:53 +00:00
*/
if (gpiolib_initialized) {
ret = gpiochip_setup_dev(gdev);
if (ret)
goto err_remove_irqchip;
}
return 0;
err_remove_irqchip:
gpiochip_irqchip_remove(gc);
err_remove_irqchip_mask:
gpiochip_irqchip_free_valid_mask(gc);
gpio: Fix gpiochip_add_data_with_key() error path The err_remove_chip block is too coarse, and may perform cleanup that must not be done. E.g. if of_gpiochip_add() fails, of_gpiochip_remove() is still called, causing: OF: ERROR: Bad of_node_put() on /soc/gpio@e6050000 CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.1.0-rc2-koelsch+ #407 Hardware name: Generic R-Car Gen2 (Flattened Device Tree) Workqueue: events deferred_probe_work_func [<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14) [<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c) [<c07c1224>] (dump_stack) from [<c07c5a80>] (kobject_put+0x94/0xbc) [<c07c5a80>] (kobject_put) from [<c0470420>] (gpiochip_add_data_with_key+0x8d8/0xa3c) [<c0470420>] (gpiochip_add_data_with_key) from [<c0473738>] (gpio_rcar_probe+0x1d4/0x314) [<c0473738>] (gpio_rcar_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94) and later, if a GPIO consumer tries to use a GPIO from a failed controller: WARNING: CPU: 0 PID: 1 at lib/refcount.c:156 kobject_get+0x38/0x4c refcount_t: increment on 0; use-after-free. Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.1.0-rc2-koelsch+ #407 Hardware name: Generic R-Car Gen2 (Flattened Device Tree) [<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14) [<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c) [<c07c1224>] (dump_stack) from [<c0221580>] (__warn+0xd0/0xec) [<c0221580>] (__warn) from [<c02215e0>] (warn_slowpath_fmt+0x44/0x6c) [<c02215e0>] (warn_slowpath_fmt) from [<c07c58fc>] (kobject_get+0x38/0x4c) [<c07c58fc>] (kobject_get) from [<c068b3ec>] (of_node_get+0x14/0x1c) [<c068b3ec>] (of_node_get) from [<c0686f24>] (of_find_node_by_phandle+0xc0/0xf0) [<c0686f24>] (of_find_node_by_phandle) from [<c0686fbc>] (of_phandle_iterator_next+0x68/0x154) [<c0686fbc>] (of_phandle_iterator_next) from [<c0687fe4>] (__of_parse_phandle_with_args+0x40/0xd0) [<c0687fe4>] (__of_parse_phandle_with_args) from [<c0688204>] (of_parse_phandle_with_args_map+0x100/0x3ac) [<c0688204>] (of_parse_phandle_with_args_map) from [<c0471240>] (of_get_named_gpiod_flags+0x38/0x380) [<c0471240>] (of_get_named_gpiod_flags) from [<c046f864>] (gpiod_get_from_of_node+0x24/0xd8) [<c046f864>] (gpiod_get_from_of_node) from [<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child+0xa0/0x144) [<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child) from [<c05f425c>] (gpio_keys_probe+0x418/0x7bc) [<c05f425c>] (gpio_keys_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94) Fix this by splitting the cleanup block, and adding a missing call to gpiochip_irqchip_remove(). Fixes: 28355f81969962cf ("gpio: defer probe if pinctrl cannot be found") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-04-24 13:59:33 +00:00
err_remove_acpi_chip:
acpi_gpiochip_remove(gc);
gpio: Fix gpiochip_add_data_with_key() error path The err_remove_chip block is too coarse, and may perform cleanup that must not be done. E.g. if of_gpiochip_add() fails, of_gpiochip_remove() is still called, causing: OF: ERROR: Bad of_node_put() on /soc/gpio@e6050000 CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.1.0-rc2-koelsch+ #407 Hardware name: Generic R-Car Gen2 (Flattened Device Tree) Workqueue: events deferred_probe_work_func [<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14) [<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c) [<c07c1224>] (dump_stack) from [<c07c5a80>] (kobject_put+0x94/0xbc) [<c07c5a80>] (kobject_put) from [<c0470420>] (gpiochip_add_data_with_key+0x8d8/0xa3c) [<c0470420>] (gpiochip_add_data_with_key) from [<c0473738>] (gpio_rcar_probe+0x1d4/0x314) [<c0473738>] (gpio_rcar_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94) and later, if a GPIO consumer tries to use a GPIO from a failed controller: WARNING: CPU: 0 PID: 1 at lib/refcount.c:156 kobject_get+0x38/0x4c refcount_t: increment on 0; use-after-free. Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.1.0-rc2-koelsch+ #407 Hardware name: Generic R-Car Gen2 (Flattened Device Tree) [<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14) [<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c) [<c07c1224>] (dump_stack) from [<c0221580>] (__warn+0xd0/0xec) [<c0221580>] (__warn) from [<c02215e0>] (warn_slowpath_fmt+0x44/0x6c) [<c02215e0>] (warn_slowpath_fmt) from [<c07c58fc>] (kobject_get+0x38/0x4c) [<c07c58fc>] (kobject_get) from [<c068b3ec>] (of_node_get+0x14/0x1c) [<c068b3ec>] (of_node_get) from [<c0686f24>] (of_find_node_by_phandle+0xc0/0xf0) [<c0686f24>] (of_find_node_by_phandle) from [<c0686fbc>] (of_phandle_iterator_next+0x68/0x154) [<c0686fbc>] (of_phandle_iterator_next) from [<c0687fe4>] (__of_parse_phandle_with_args+0x40/0xd0) [<c0687fe4>] (__of_parse_phandle_with_args) from [<c0688204>] (of_parse_phandle_with_args_map+0x100/0x3ac) [<c0688204>] (of_parse_phandle_with_args_map) from [<c0471240>] (of_get_named_gpiod_flags+0x38/0x380) [<c0471240>] (of_get_named_gpiod_flags) from [<c046f864>] (gpiod_get_from_of_node+0x24/0xd8) [<c046f864>] (gpiod_get_from_of_node) from [<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child+0xa0/0x144) [<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child) from [<c05f425c>] (gpio_keys_probe+0x418/0x7bc) [<c05f425c>] (gpio_keys_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94) Fix this by splitting the cleanup block, and adding a missing call to gpiochip_irqchip_remove(). Fixes: 28355f81969962cf ("gpio: defer probe if pinctrl cannot be found") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-04-24 13:59:33 +00:00
err_remove_of_chip:
gpiochip_free_hogs(gc);
of_gpiochip_remove(gc);
gpio: Fix gpiochip_add_data_with_key() error path The err_remove_chip block is too coarse, and may perform cleanup that must not be done. E.g. if of_gpiochip_add() fails, of_gpiochip_remove() is still called, causing: OF: ERROR: Bad of_node_put() on /soc/gpio@e6050000 CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.1.0-rc2-koelsch+ #407 Hardware name: Generic R-Car Gen2 (Flattened Device Tree) Workqueue: events deferred_probe_work_func [<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14) [<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c) [<c07c1224>] (dump_stack) from [<c07c5a80>] (kobject_put+0x94/0xbc) [<c07c5a80>] (kobject_put) from [<c0470420>] (gpiochip_add_data_with_key+0x8d8/0xa3c) [<c0470420>] (gpiochip_add_data_with_key) from [<c0473738>] (gpio_rcar_probe+0x1d4/0x314) [<c0473738>] (gpio_rcar_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94) and later, if a GPIO consumer tries to use a GPIO from a failed controller: WARNING: CPU: 0 PID: 1 at lib/refcount.c:156 kobject_get+0x38/0x4c refcount_t: increment on 0; use-after-free. Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.1.0-rc2-koelsch+ #407 Hardware name: Generic R-Car Gen2 (Flattened Device Tree) [<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14) [<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c) [<c07c1224>] (dump_stack) from [<c0221580>] (__warn+0xd0/0xec) [<c0221580>] (__warn) from [<c02215e0>] (warn_slowpath_fmt+0x44/0x6c) [<c02215e0>] (warn_slowpath_fmt) from [<c07c58fc>] (kobject_get+0x38/0x4c) [<c07c58fc>] (kobject_get) from [<c068b3ec>] (of_node_get+0x14/0x1c) [<c068b3ec>] (of_node_get) from [<c0686f24>] (of_find_node_by_phandle+0xc0/0xf0) [<c0686f24>] (of_find_node_by_phandle) from [<c0686fbc>] (of_phandle_iterator_next+0x68/0x154) [<c0686fbc>] (of_phandle_iterator_next) from [<c0687fe4>] (__of_parse_phandle_with_args+0x40/0xd0) [<c0687fe4>] (__of_parse_phandle_with_args) from [<c0688204>] (of_parse_phandle_with_args_map+0x100/0x3ac) [<c0688204>] (of_parse_phandle_with_args_map) from [<c0471240>] (of_get_named_gpiod_flags+0x38/0x380) [<c0471240>] (of_get_named_gpiod_flags) from [<c046f864>] (gpiod_get_from_of_node+0x24/0xd8) [<c046f864>] (gpiod_get_from_of_node) from [<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child+0xa0/0x144) [<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child) from [<c05f425c>] (gpio_keys_probe+0x418/0x7bc) [<c05f425c>] (gpio_keys_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94) Fix this by splitting the cleanup block, and adding a missing call to gpiochip_irqchip_remove(). Fixes: 28355f81969962cf ("gpio: defer probe if pinctrl cannot be found") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-04-24 13:59:33 +00:00
err_free_gpiochip_mask:
gpiochip_remove_pin_ranges(gc);
gpiochip_free_valid_mask(gc);
err_remove_from_list:
spin_lock_irqsave(&gpio_lock, flags);
list_del(&gdev->list);
spin_unlock_irqrestore(&gpio_lock, flags);
err_free_label:
kfree_const(gdev->label);
err_free_descs:
kfree(gdev->descs);
err_free_ida:
ida_free(&gpio_ida, gdev->id);
err_free_gdev:
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/* failures here can mean systems won't boot... */
pr_err("%s: GPIOs %d..%d (%s) failed to register, %d\n", __func__,
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
gdev->base, gdev->base + gdev->ngpio - 1,
gc->label ? : "generic", ret);
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
kfree(gdev);
return ret;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
EXPORT_SYMBOL_GPL(gpiochip_add_data_with_key);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiochip_get_data() - get per-subdriver data for the chip
* @gc: GPIO chip
*
* Returns:
* The per-subdriver data for the chip.
*/
void *gpiochip_get_data(struct gpio_chip *gc)
{
return gc->gpiodev->data;
}
EXPORT_SYMBOL_GPL(gpiochip_get_data);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiochip_remove() - unregister a gpio_chip
* @gc: the chip to unregister
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*
* A gpio_chip with any GPIOs still requested may not be removed.
*/
void gpiochip_remove(struct gpio_chip *gc)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
struct gpio_device *gdev = gc->gpiodev;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
unsigned long flags;
unsigned int i;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/* FIXME: should the legacy sysfs handling be moved to gpio_device? */
gpiochip_sysfs_unregister(gdev);
gpiochip_free_hogs(gc);
/* Numb the device, cancelling all outstanding operations */
gdev->chip = NULL;
gpiochip_irqchip_remove(gc);
acpi_gpiochip_remove(gc);
of_gpiochip_remove(gc);
gpiochip_remove_pin_ranges(gc);
gpiochip_free_valid_mask(gc);
/*
* We accept no more calls into the driver from this point, so
* NULL the driver data pointer
*/
gdev->data = NULL;
spin_lock_irqsave(&gpio_lock, flags);
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
for (i = 0; i < gdev->ngpio; i++) {
if (gpiochip_is_requested(gc, i))
break;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
spin_unlock_irqrestore(&gpio_lock, flags);
if (i != gdev->ngpio)
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
dev_crit(&gdev->dev,
gpio: change member .dev to .parent The name .dev in a struct is normally reserved for a struct device that is let us say a superclass to the thing described by the struct. struct gpio_chip stands out by confusingly using a struct device *dev to point to the parent device (such as a platform_device) that represents the hardware. As we want to give gpio_chip:s real devices, this is not working. We need to rename this member to parent. This was done by two coccinelle scripts, I guess it is possible to combine them into one, but I don't know such stuff. They look like this: @@ struct gpio_chip *var; @@ -var->dev +var->parent and: @@ struct gpio_chip var; @@ -var.dev +var.parent and: @@ struct bgpio_chip *var; @@ -var->gc.dev +var->gc.parent Plus a few instances of bgpio that I couldn't figure out how to teach Coccinelle to rewrite. This patch hits all over the place, but I *strongly* prefer this solution to any piecemal approaches that just exercise patch mechanics all over the place. It mainly hits drivers/gpio and drivers/pinctrl which is my own backyard anyway. Cc: Haavard Skinnemoen <hskinnemoen@gmail.com> Cc: Rafał Miłecki <zajec5@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Alek Du <alek.du@intel.com> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Jiri Kosina <jkosina@suse.cz> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-04 08:56:26 +00:00
"REMOVING GPIOCHIP WITH GPIOS STILL REQUESTED\n");
/*
* The gpiochip side puts its use of the device to rest here:
* if there are no userspace clients, the chardev and device will
* be removed, else it will be dangling until the last user is
* gone.
*/
gcdev_unregister(gdev);
put_device(&gdev->dev);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
EXPORT_SYMBOL_GPL(gpiochip_remove);
/**
* gpiochip_find() - iterator for locating a specific gpio_chip
* @data: data to pass to match function
* @match: Callback function to check gpio_chip
*
* Similar to bus_find_device. It returns a reference to a gpio_chip as
* determined by a user supplied @match callback. The callback should return
* 0 if the device doesn't match and non-zero if it does. If the callback is
* non-zero, this function will return to the caller and not iterate over any
* more gpio_chips.
*/
struct gpio_chip *gpiochip_find(void *data,
int (*match)(struct gpio_chip *gc,
void *data))
{
struct gpio_device *gdev;
struct gpio_chip *gc = NULL;
unsigned long flags;
spin_lock_irqsave(&gpio_lock, flags);
list_for_each_entry(gdev, &gpio_devices, list)
if (gdev->chip && match(gdev->chip, data)) {
gc = gdev->chip;
break;
}
spin_unlock_irqrestore(&gpio_lock, flags);
return gc;
}
EXPORT_SYMBOL_GPL(gpiochip_find);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
static int gpiochip_match_name(struct gpio_chip *gc, void *data)
{
const char *name = data;
return !strcmp(gc->label, name);
}
static struct gpio_chip *find_chip_by_name(const char *name)
{
return gpiochip_find((void *)name, gpiochip_match_name);
}
#ifdef CONFIG_GPIOLIB_IRQCHIP
/*
* The following is irqchip helper code for gpiochips.
*/
static int gpiochip_irqchip_init_hw(struct gpio_chip *gc)
{
struct gpio_irq_chip *girq = &gc->irq;
if (!girq->init_hw)
return 0;
return girq->init_hw(gc);
}
static int gpiochip_irqchip_init_valid_mask(struct gpio_chip *gc)
{
struct gpio_irq_chip *girq = &gc->irq;
if (!girq->init_valid_mask)
return 0;
girq->valid_mask = gpiochip_allocate_mask(gc);
if (!girq->valid_mask)
return -ENOMEM;
girq->init_valid_mask(gc, girq->valid_mask, gc->ngpio);
return 0;
}
static void gpiochip_irqchip_free_valid_mask(struct gpio_chip *gc)
{
bitmap_free(gc->irq.valid_mask);
gc->irq.valid_mask = NULL;
}
bool gpiochip_irqchip_irq_valid(const struct gpio_chip *gc,
unsigned int offset)
{
if (!gpiochip_line_is_valid(gc, offset))
return false;
/* No mask means all valid */
if (likely(!gc->irq.valid_mask))
return true;
return test_bit(offset, gc->irq.valid_mask);
}
EXPORT_SYMBOL_GPL(gpiochip_irqchip_irq_valid);
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
#ifdef CONFIG_IRQ_DOMAIN_HIERARCHY
/**
* gpiochip_set_hierarchical_irqchip() - connects a hierarchical irqchip
* to a gpiochip
* @gc: the gpiochip to set the irqchip hierarchical handler to
* @irqchip: the irqchip to handle this level of the hierarchy, the interrupt
* will then percolate up to the parent
*/
static void gpiochip_set_hierarchical_irqchip(struct gpio_chip *gc,
struct irq_chip *irqchip)
{
/* DT will deal with mapping each IRQ as we go along */
if (is_of_node(gc->irq.fwnode))
return;
/*
* This is for legacy and boardfile "irqchip" fwnodes: allocate
* irqs upfront instead of dynamically since we don't have the
* dynamic type of allocation that hardware description languages
* provide. Once all GPIO drivers using board files are gone from
* the kernel we can delete this code, but for a transitional period
* it is necessary to keep this around.
*/
if (is_fwnode_irqchip(gc->irq.fwnode)) {
int i;
int ret;
for (i = 0; i < gc->ngpio; i++) {
struct irq_fwspec fwspec;
unsigned int parent_hwirq;
unsigned int parent_type;
struct gpio_irq_chip *girq = &gc->irq;
/*
* We call the child to parent translation function
* only to check if the child IRQ is valid or not.
* Just pick the rising edge type here as that is what
* we likely need to support.
*/
ret = girq->child_to_parent_hwirq(gc, i,
IRQ_TYPE_EDGE_RISING,
&parent_hwirq,
&parent_type);
if (ret) {
chip_err(gc, "skip set-up on hwirq %d\n",
i);
continue;
}
fwspec.fwnode = gc->irq.fwnode;
/* This is the hwirq for the GPIO line side of things */
fwspec.param[0] = girq->child_offset_to_irq(gc, i);
/* Just pick something */
fwspec.param[1] = IRQ_TYPE_EDGE_RISING;
fwspec.param_count = 2;
ret = __irq_domain_alloc_irqs(gc->irq.domain,
/* just pick something */
-1,
1,
NUMA_NO_NODE,
&fwspec,
false,
NULL);
if (ret < 0) {
chip_err(gc,
"can not allocate irq for GPIO line %d parent hwirq %d in hierarchy domain: %d\n",
i, parent_hwirq,
ret);
}
}
}
chip_err(gc, "%s unknown fwnode type proceed anyway\n", __func__);
return;
}
static int gpiochip_hierarchy_irq_domain_translate(struct irq_domain *d,
struct irq_fwspec *fwspec,
unsigned long *hwirq,
unsigned int *type)
{
/* We support standard DT translation */
if (is_of_node(fwspec->fwnode) && fwspec->param_count == 2) {
return irq_domain_translate_twocell(d, fwspec, hwirq, type);
}
/* This is for board files and others not using DT */
if (is_fwnode_irqchip(fwspec->fwnode)) {
int ret;
ret = irq_domain_translate_twocell(d, fwspec, hwirq, type);
if (ret)
return ret;
WARN_ON(*type == IRQ_TYPE_NONE);
return 0;
}
return -EINVAL;
}
static int gpiochip_hierarchy_irq_domain_alloc(struct irq_domain *d,
unsigned int irq,
unsigned int nr_irqs,
void *data)
{
struct gpio_chip *gc = d->host_data;
irq_hw_number_t hwirq;
unsigned int type = IRQ_TYPE_NONE;
struct irq_fwspec *fwspec = data;
void *parent_arg;
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
unsigned int parent_hwirq;
unsigned int parent_type;
struct gpio_irq_chip *girq = &gc->irq;
int ret;
/*
* The nr_irqs parameter is always one except for PCI multi-MSI
* so this should not happen.
*/
WARN_ON(nr_irqs != 1);
ret = gc->irq.child_irq_domain_ops.translate(d, fwspec, &hwirq, &type);
if (ret)
return ret;
chip_dbg(gc, "allocate IRQ %d, hwirq %lu\n", irq, hwirq);
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
ret = girq->child_to_parent_hwirq(gc, hwirq, type,
&parent_hwirq, &parent_type);
if (ret) {
chip_err(gc, "can't look up hwirq %lu\n", hwirq);
return ret;
}
chip_dbg(gc, "found parent hwirq %u\n", parent_hwirq);
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
/*
* We set handle_bad_irq because the .set_type() should
* always be invoked and set the right type of handler.
*/
irq_domain_set_info(d,
irq,
hwirq,
gc->irq.chip,
gc,
girq->handler,
NULL, NULL);
irq_set_probe(irq);
/* This parent only handles asserted level IRQs */
parent_arg = girq->populate_parent_alloc_arg(gc, parent_hwirq, parent_type);
if (!parent_arg)
return -ENOMEM;
chip_dbg(gc, "alloc_irqs_parent for %d parent hwirq %d\n",
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
irq, parent_hwirq);
gpiolib: Set lockdep class for hierarchical irq domains I see the following lockdep splat in the qcom pinctrl driver when attempting to suspend the device. ============================================ WARNING: possible recursive locking detected 5.4.2 #2 Tainted: G S -------------------------------------------- cat/6536 is trying to acquire lock: ffffff814787ccc0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94 but task is already holding lock: ffffff81436740c0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&irq_desc_lock_class); lock(&irq_desc_lock_class); *** DEADLOCK *** May be due to missing lock nesting notation 7 locks held by cat/6536: #0: ffffff8140e0c420 (sb_writers#7){.+.+}, at: vfs_write+0xc8/0x19c #1: ffffff8121eec480 (&of->mutex){+.+.}, at: kernfs_fop_write+0x128/0x1f4 #2: ffffff8147cad668 (kn->count#263){.+.+}, at: kernfs_fop_write+0x130/0x1f4 #3: ffffffd011446000 (system_transition_mutex){+.+.}, at: pm_suspend+0x108/0x354 #4: ffffff814302b970 (&dev->mutex){....}, at: __device_suspend+0x16c/0x420 #5: ffffff81436740c0 (&irq_desc_lock_class){-.-.}, at: __irq_get_desc_lock+0x64/0x94 #6: ffffff81479b8c10 (&pctrl->lock){....}, at: msm_gpio_irq_set_wake+0x48/0x7c stack backtrace: CPU: 4 PID: 6536 Comm: cat Tainted: G S 5.4.2 #2 Call trace: dump_backtrace+0x0/0x174 show_stack+0x20/0x2c dump_stack+0xdc/0x144 __lock_acquire+0x52c/0x2268 lock_acquire+0x1dc/0x220 _raw_spin_lock_irqsave+0x64/0x80 __irq_get_desc_lock+0x64/0x94 irq_set_irq_wake+0x40/0x144 msm_gpio_irq_set_wake+0x5c/0x7c set_irq_wake_real+0x40/0x5c irq_set_irq_wake+0x70/0x144 cros_ec_rtc_suspend+0x38/0x4c platform_pm_suspend+0x34/0x60 dpm_run_callback+0x64/0xcc __device_suspend+0x314/0x420 dpm_suspend+0xf8/0x298 dpm_suspend_start+0x84/0xb4 suspend_devices_and_enter+0xbc/0x628 pm_suspend+0x214/0x354 state_store+0xb0/0x108 kobj_attr_store+0x14/0x24 sysfs_kf_write+0x4c/0x64 kernfs_fop_write+0x158/0x1f4 __vfs_write+0x54/0x18c vfs_write+0xdc/0x19c ksys_write+0x7c/0xe4 __arm64_sys_write+0x20/0x2c el0_svc_common+0xa8/0x160 el0_svc_compat_handler+0x2c/0x38 el0_svc_compat+0x8/0x10 This is because the msm_gpio_irq_set_wake() function calls irq_set_irq_wake() as a backup in case the irq comes in during the path to idle. Given that we're calling irqchip functions from within an irqchip we need to set the lockdep class to be different for this child controller vs. the default one that the parent irqchip gets. This used to be done before this driver was converted to hierarchical irq domains in commit e35a6ae0eb3a ("pinctrl/msm: Setup GPIO chip in hierarchy") via the gpiochip_irq_map() function. With hierarchical irq domains this function has been replaced by gpiochip_hierarchy_irq_domain_alloc(). Therefore, set the lockdep class like was done previously in the irq domain path so we can avoid this lockdep warning. Fixes: fdd61a013a24 ("gpio: Add support for hierarchical IRQ domains") Cc: Thierry Reding <treding@nvidia.com> Cc: Brian Masney <masneyb@onstation.org> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Marc Zyngier <maz@kernel.org> Cc: Maulik Shah <mkshah@codeaurora.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20200114231103.85641-1-swboyd@chromium.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-01-14 23:11:03 +00:00
irq_set_lockdep_class(irq, gc->irq.lock_key, gc->irq.request_key);
ret = irq_domain_alloc_irqs_parent(d, irq, 1, parent_arg);
/*
* If the parent irqdomain is msi, the interrupts have already
* been allocated, so the EEXIST is good.
*/
if (irq_domain_is_msi(d->parent) && (ret == -EEXIST))
ret = 0;
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
if (ret)
chip_err(gc,
"failed to allocate parent hwirq %d for hwirq %lu\n",
parent_hwirq, hwirq);
kfree(parent_arg);
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
return ret;
}
static unsigned int gpiochip_child_offset_to_irq_noop(struct gpio_chip *gc,
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
unsigned int offset)
{
return offset;
}
static void gpiochip_hierarchy_setup_domain_ops(struct irq_domain_ops *ops)
{
ops->activate = gpiochip_irq_domain_activate;
ops->deactivate = gpiochip_irq_domain_deactivate;
ops->alloc = gpiochip_hierarchy_irq_domain_alloc;
ops->free = irq_domain_free_irqs_common;
/*
* We only allow overriding the translate() function for
* hierarchical chips, and this should only be done if the user
* really need something other than 1:1 translation.
*/
if (!ops->translate)
ops->translate = gpiochip_hierarchy_irq_domain_translate;
}
static int gpiochip_hierarchy_add_domain(struct gpio_chip *gc)
{
if (!gc->irq.child_to_parent_hwirq ||
!gc->irq.fwnode) {
chip_err(gc, "missing irqdomain vital data\n");
return -EINVAL;
}
if (!gc->irq.child_offset_to_irq)
gc->irq.child_offset_to_irq = gpiochip_child_offset_to_irq_noop;
if (!gc->irq.populate_parent_alloc_arg)
gc->irq.populate_parent_alloc_arg =
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
gpiochip_populate_parent_fwspec_twocell;
gpiochip_hierarchy_setup_domain_ops(&gc->irq.child_irq_domain_ops);
gc->irq.domain = irq_domain_create_hierarchy(
gc->irq.parent_domain,
0,
gc->ngpio,
gc->irq.fwnode,
&gc->irq.child_irq_domain_ops,
gc);
if (!gc->irq.domain)
return -ENOMEM;
gpiochip_set_hierarchical_irqchip(gc, gc->irq.chip);
return 0;
}
static bool gpiochip_hierarchy_is_hierarchical(struct gpio_chip *gc)
{
return !!gc->irq.parent_domain;
}
void *gpiochip_populate_parent_fwspec_twocell(struct gpio_chip *gc,
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
unsigned int parent_hwirq,
unsigned int parent_type)
{
struct irq_fwspec *fwspec;
fwspec = kmalloc(sizeof(*fwspec), GFP_KERNEL);
if (!fwspec)
return NULL;
fwspec->fwnode = gc->irq.parent_domain->fwnode;
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
fwspec->param_count = 2;
fwspec->param[0] = parent_hwirq;
fwspec->param[1] = parent_type;
return fwspec;
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
}
EXPORT_SYMBOL_GPL(gpiochip_populate_parent_fwspec_twocell);
void *gpiochip_populate_parent_fwspec_fourcell(struct gpio_chip *gc,
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
unsigned int parent_hwirq,
unsigned int parent_type)
{
struct irq_fwspec *fwspec;
fwspec = kmalloc(sizeof(*fwspec), GFP_KERNEL);
if (!fwspec)
return NULL;
fwspec->fwnode = gc->irq.parent_domain->fwnode;
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
fwspec->param_count = 4;
fwspec->param[0] = 0;
fwspec->param[1] = parent_hwirq;
fwspec->param[2] = 0;
fwspec->param[3] = parent_type;
return fwspec;
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
}
EXPORT_SYMBOL_GPL(gpiochip_populate_parent_fwspec_fourcell);
#else
static int gpiochip_hierarchy_add_domain(struct gpio_chip *gc)
{
return -EINVAL;
}
static bool gpiochip_hierarchy_is_hierarchical(struct gpio_chip *gc)
{
return false;
}
#endif /* CONFIG_IRQ_DOMAIN_HIERARCHY */
/**
* gpiochip_irq_map() - maps an IRQ into a GPIO irqchip
* @d: the irqdomain used by this irqchip
* @irq: the global irq number used by this GPIO irqchip irq
* @hwirq: the local IRQ/GPIO line offset on this gpiochip
*
* This function will set up the mapping for a certain IRQ line on a
* gpiochip by assigning the gpiochip as chip data, and using the irqchip
* stored inside the gpiochip.
*/
int gpiochip_irq_map(struct irq_domain *d, unsigned int irq,
irq_hw_number_t hwirq)
{
struct gpio_chip *gc = d->host_data;
int ret = 0;
if (!gpiochip_irqchip_irq_valid(gc, hwirq))
gpiolib: allow gpio irqchip to map irqs dynamically Now IRQ mappings are always created for all (allowed) GPIOs in gpiochip in gpiochip_irqchip_add_key() which goes against the idea of SPARSE_IRQ and, as result, leads to: - increasing of memory consumption for IRQ descriptors most of which will never ever be used (espessially on platform with a high number of GPIOs). (sizeof(struct irq_desc) == 256 on my tested platforms) - imposibility to use GPIO irqchip APIs by gpio drivers when HW implements GPIO IRQ functionality as IRQ crossbar/router which has only limited number of IRQ outputs (example from [1], all GPIOs can be mapped on only 8 IRQs). Hence, remove static IRQ mapping code from gpiochip_irqchip_add_key() and instead replace irq_find_mapping() with irq_create_mapping() in gpiochip_to_irq(). Also add additional gpiochip_irqchip_irq_valid() calls in gpiochip_to_irq() and gpiochip_irq_map(). After this change gpio2irq mapping will happen the following way when GPIO irqchip APIs are used by gpio driver: - IRQ mappings will be created statically if driver passes first_irq>0 vlaue in gpiochip_irqchip_add_key(). - IRQ mappings will be created dynamically from gpio_to_irq() or of_irq_get(). Tested on am335x-evm and dra72-evm-revc. - dra72-evm-revc: number of created irq mappings decreased from 402 -> 135 Mem savings 267*256 = 68352 (66kB) - am335x-evm: number of created irq mappings decreased from 188 -> 63 Mem savings 125*256 = 32000 (31kB) [1] https://lkml.org/lkml/2017/6/15/428 Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-07-21 16:49:00 +00:00
return -ENXIO;
irq_set_chip_data(irq, gc);
gpiolib: irqchip: use different lockdep class for each gpio irqchip Since IRQ chip helpers were introduced drivers lose ability to register separate lockdep classes for each registered GPIO IRQ chip and the gpiolib now is using shared lockdep class for all GPIO IRQ chips (gpiochip_irq_lock_class). As result, lockdep will produce warning when there are min two stacked GPIO chips and all of them are interrupt controllers. HW configuration which generates lockdep warning (TI dra7-evm): [SOC GPIO bankA.gpioX] <- irq - [pcf875x.gpioY] <- irq - DevZ.enable_irq_wake(pcf_gpioY_irq); The issue was reported in [1] and discussed [2]. ============================================= [ INFO: possible recursive locking detected ] 4.2.0-rc6-00013-g5d050ed-dirty #55 Not tainted --------------------------------------------- sh/63 is trying to acquire lock: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94 but task is already holding lock: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(class); lock(class); *** DEADLOCK *** May be due to missing lock nesting notation 7 locks held by sh/63: #0: (sb_writers#4){.+.+.+}, at: [<c016bbb8>] vfs_write+0x13c/0x164 #1: (&of->mutex){+.+.+.}, at: [<c01debf4>] kernfs_fop_write+0x4c/0x1a0 #2: (s_active#36){.+.+.+}, at: [<c01debfc>] kernfs_fop_write+0x54/0x1a0 #3: (pm_mutex){+.+.+.}, at: [<c009758c>] pm_suspend+0xec/0x4c4 #4: (&dev->mutex){......}, at: [<c03f77f8>] __device_suspend+0xd4/0x398 #5: (&gpio->lock){+.+.+.}, at: [<c009b940>] __irq_get_desc_lock+0x74/0x94 #6: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94 stack backtrace: CPU: 0 PID: 63 Comm: sh Not tainted 4.2.0-rc6-00013-g5d050ed-dirty #55 Hardware name: Generic DRA74X (Flattened Device Tree) [<c0016e24>] (unwind_backtrace) from [<c0013338>] (show_stack+0x10/0x14) [<c0013338>] (show_stack) from [<c05f6b24>] (dump_stack+0x84/0x9c) [<c05f6b24>] (dump_stack) from [<c00903f4>] (__lock_acquire+0x19c0/0x1e20) [<c00903f4>] (__lock_acquire) from [<c0091098>] (lock_acquire+0xa8/0x128) [<c0091098>] (lock_acquire) from [<c05fd61c>] (_raw_spin_lock_irqsave+0x38/0x4c) [<c05fd61c>] (_raw_spin_lock_irqsave) from [<c009b91c>] (__irq_get_desc_lock+0x50/0x94) [<c009b91c>] (__irq_get_desc_lock) from [<c009c4f4>] (irq_set_irq_wake+0x20/0xfc) [<c009c4f4>] (irq_set_irq_wake) from [<c0393ac4>] (pcf857x_irq_set_wake+0x24/0x54) [<c0393ac4>] (pcf857x_irq_set_wake) from [<c009c560>] (irq_set_irq_wake+0x8c/0xfc) [<c009c560>] (irq_set_irq_wake) from [<c04a02ac>] (gpio_keys_suspend+0x70/0xd4) [<c04a02ac>] (gpio_keys_suspend) from [<c03f6a00>] (dpm_run_callback+0x50/0x124) [<c03f6a00>] (dpm_run_callback) from [<c03f7830>] (__device_suspend+0x10c/0x398) [<c03f7830>] (__device_suspend) from [<c03f90f0>] (dpm_suspend+0x134/0x2f4) [<c03f90f0>] (dpm_suspend) from [<c0096e20>] (suspend_devices_and_enter+0xa8/0x728) [<c0096e20>] (suspend_devices_and_enter) from [<c00977cc>] (pm_suspend+0x32c/0x4c4) [<c00977cc>] (pm_suspend) from [<c0096060>] (state_store+0x64/0xb8) [<c0096060>] (state_store) from [<c01dec64>] (kernfs_fop_write+0xbc/0x1a0) [<c01dec64>] (kernfs_fop_write) from [<c016b280>] (__vfs_write+0x20/0xd8) [<c016b280>] (__vfs_write) from [<c016bb0c>] (vfs_write+0x90/0x164) [<c016bb0c>] (vfs_write) from [<c016c330>] (SyS_write+0x44/0x9c) [<c016c330>] (SyS_write) from [<c000f500>] (ret_fast_syscall+0x0/0x54) Lets fix it by using separate lockdep class for each registered GPIO IRQ Chip. This is done by wrapping gpiochip_irqchip_add call into macros. The implementation of this patch inspired by solution done by Nicolas Boichat for regmap [3] [1] http://www.spinics.net/lists/linux-gpio/msg05844.html [2] http://www.spinics.net/lists/linux-gpio/msg06021.html [3] http://www.spinics.net/lists/arm-kernel/msg429834.html Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Roger Quadros <rogerq@ti.com> Reported-by: Roger Quadros <rogerq@ti.com> Tested-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-17 12:35:23 +00:00
/*
* This lock class tells lockdep that GPIO irqs are in a different
* category than their parents, so it won't report false recursion.
*/
irq_set_lockdep_class(irq, gc->irq.lock_key, gc->irq.request_key);
irq_set_chip_and_handler(irq, gc->irq.chip, gc->irq.handler);
gpio: simplify adding threaded interrupts This tries to simplify the use of CONFIG_GPIOLIB_IRQCHIP when using threaded interrupts: add a new call gpiochip_irqchip_add_nested() to indicate that we're dealing with a nested rather than a chained irqchip, then create a separate gpiochip_set_nested_irqchip() to mirror the gpiochip_set_chained_irqchip() call to connect the parent and child interrupts. In the nested case gpiochip_set_nested_irqchip() does nothing more than call irq_set_parent() on each valid child interrupt, which has little semantic effect in the kernel, but this is probably still formally correct. Update all drivers using nested interrupts to use gpiochip_irqchip_add_nested() so we can now see clearly which these users are. The DLN2 driver can drop its specific hack with .irq_not_threaded as we now recognize whether a chip is threaded or not from its use of gpiochip_irqchip_add_nested() signature rather than from inspecting .can_sleep. We rename the .irq_parent to .irq_chained_parent since this parent IRQ is only really kept around for the chained interrupt handlers. Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Octavian Purdila <octavian.purdila@intel.com> Cc: Daniel Baluta <daniel.baluta@intel.com> Cc: Bin Gao <bin.gao@linux.intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com> Cc: Semen Protsenko <semen.protsenko@globallogic.com> Cc: Alexander Stein <alexander.stein@systec-electronic.com> Cc: Phil Reid <preid@electromag.com.au> Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com> Cc: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-11-24 09:57:25 +00:00
/* Chips that use nested thread handlers have them marked */
if (gc->irq.threaded)
irq_set_nested_thread(irq, 1);
irq_set_noprobe(irq);
if (gc->irq.num_parents == 1)
ret = irq_set_parent(irq, gc->irq.parents[0]);
else if (gc->irq.map)
ret = irq_set_parent(irq, gc->irq.map[hwirq]);
if (ret < 0)
return ret;
/*
* No set-up of the hardware will happen if IRQ_TYPE_NONE
* is passed as default type.
*/
if (gc->irq.default_type != IRQ_TYPE_NONE)
irq_set_irq_type(irq, gc->irq.default_type);
return 0;
}
EXPORT_SYMBOL_GPL(gpiochip_irq_map);
void gpiochip_irq_unmap(struct irq_domain *d, unsigned int irq)
{
struct gpio_chip *gc = d->host_data;
if (gc->irq.threaded)
irq_set_nested_thread(irq, 0);
irq_set_chip_and_handler(irq, NULL, NULL);
irq_set_chip_data(irq, NULL);
}
EXPORT_SYMBOL_GPL(gpiochip_irq_unmap);
static const struct irq_domain_ops gpiochip_domain_ops = {
.map = gpiochip_irq_map,
.unmap = gpiochip_irq_unmap,
/* Virtually all GPIO irqchips are twocell:ed */
.xlate = irq_domain_xlate_twocell,
};
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
/*
* TODO: move these activate/deactivate in under the hierarchicial
* irqchip implementation as static once SPMI and SSBI (all external
* users) are phased over.
*/
/**
* gpiochip_irq_domain_activate() - Lock a GPIO to be used as an IRQ
* @domain: The IRQ domain used by this IRQ chip
* @data: Outermost irq_data associated with the IRQ
* @reserve: If set, only reserve an interrupt vector instead of assigning one
*
* This function is a wrapper that calls gpiochip_lock_as_irq() and is to be
* used as the activate function for the &struct irq_domain_ops. The host_data
* for the IRQ domain must be the &struct gpio_chip.
*/
int gpiochip_irq_domain_activate(struct irq_domain *domain,
struct irq_data *data, bool reserve)
{
struct gpio_chip *gc = domain->host_data;
return gpiochip_lock_as_irq(gc, data->hwirq);
}
EXPORT_SYMBOL_GPL(gpiochip_irq_domain_activate);
/**
* gpiochip_irq_domain_deactivate() - Unlock a GPIO used as an IRQ
* @domain: The IRQ domain used by this IRQ chip
* @data: Outermost irq_data associated with the IRQ
*
* This function is a wrapper that will call gpiochip_unlock_as_irq() and is to
* be used as the deactivate function for the &struct irq_domain_ops. The
* host_data for the IRQ domain must be the &struct gpio_chip.
*/
void gpiochip_irq_domain_deactivate(struct irq_domain *domain,
struct irq_data *data)
{
struct gpio_chip *gc = domain->host_data;
return gpiochip_unlock_as_irq(gc, data->hwirq);
}
EXPORT_SYMBOL_GPL(gpiochip_irq_domain_deactivate);
static int gpiochip_to_irq(struct gpio_chip *gc, unsigned int offset)
{
struct irq_domain *domain = gc->irq.domain;
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
if (!gpiochip_irqchip_irq_valid(gc, offset))
return -ENXIO;
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
#ifdef CONFIG_IRQ_DOMAIN_HIERARCHY
if (irq_domain_is_hierarchy(domain)) {
struct irq_fwspec spec;
spec.fwnode = domain->fwnode;
spec.param_count = 2;
spec.param[0] = gc->irq.child_offset_to_irq(gc, offset);
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
spec.param[1] = IRQ_TYPE_NONE;
return irq_create_fwspec_mapping(&spec);
}
#endif
return irq_create_mapping(domain, offset);
}
static int gpiochip_irq_reqres(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
return gpiochip_reqres_irq(gc, d->hwirq);
}
static void gpiochip_irq_relres(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
gpiochip_relres_irq(gc, d->hwirq);
}
static void gpiochip_irq_mask(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
if (gc->irq.irq_mask)
gc->irq.irq_mask(d);
gpiochip_disable_irq(gc, d->hwirq);
}
static void gpiochip_irq_unmask(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
gpiochip_enable_irq(gc, d->hwirq);
if (gc->irq.irq_unmask)
gc->irq.irq_unmask(d);
}
static void gpiochip_irq_enable(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
gpiochip_enable_irq(gc, d->hwirq);
gc->irq.irq_enable(d);
}
static void gpiochip_irq_disable(struct irq_data *d)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
gc->irq.irq_disable(d);
gpiochip_disable_irq(gc, d->hwirq);
}
static void gpiochip_set_irq_hooks(struct gpio_chip *gc)
{
struct irq_chip *irqchip = gc->irq.chip;
if (!irqchip->irq_request_resources &&
!irqchip->irq_release_resources) {
irqchip->irq_request_resources = gpiochip_irq_reqres;
irqchip->irq_release_resources = gpiochip_irq_relres;
}
if (WARN_ON(gc->irq.irq_enable))
return;
/* Check if the irqchip already has this hook... */
if (irqchip->irq_enable == gpiochip_irq_enable) {
/*
* ...and if so, give a gentle warning that this is bad
* practice.
*/
chip_info(gc,
"detected irqchip that is shared with multiple gpiochips: please fix the driver.\n");
return;
}
if (irqchip->irq_disable) {
gc->irq.irq_disable = irqchip->irq_disable;
irqchip->irq_disable = gpiochip_irq_disable;
} else {
gc->irq.irq_mask = irqchip->irq_mask;
irqchip->irq_mask = gpiochip_irq_mask;
}
if (irqchip->irq_enable) {
gc->irq.irq_enable = irqchip->irq_enable;
irqchip->irq_enable = gpiochip_irq_enable;
} else {
gc->irq.irq_unmask = irqchip->irq_unmask;
irqchip->irq_unmask = gpiochip_irq_unmask;
}
}
/**
* gpiochip_add_irqchip() - adds an IRQ chip to a GPIO chip
* @gc: the GPIO chip to add the IRQ chip to
* @lock_key: lockdep class for IRQ lock
* @request_key: lockdep class for IRQ request
*/
static int gpiochip_add_irqchip(struct gpio_chip *gc,
struct lock_class_key *lock_key,
struct lock_class_key *request_key)
{
struct irq_chip *irqchip = gc->irq.chip;
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
const struct irq_domain_ops *ops = NULL;
struct device_node *np;
unsigned int type;
unsigned int i;
if (!irqchip)
return 0;
if (gc->irq.parent_handler && gc->can_sleep) {
chip_err(gc, "you cannot have chained interrupts on a chip that may sleep\n");
return -EINVAL;
}
np = gc->gpiodev->dev.of_node;
type = gc->irq.default_type;
/*
* Specifying a default trigger is a terrible idea if DT or ACPI is
* used to configure the interrupts, as you may end up with
* conflicting triggers. Tell the user, and reset to NONE.
*/
if (WARN(np && type != IRQ_TYPE_NONE,
"%s: Ignoring %u default trigger\n", np->full_name, type))
type = IRQ_TYPE_NONE;
if (has_acpi_companion(gc->parent) && type != IRQ_TYPE_NONE) {
acpi_handle_warn(ACPI_HANDLE(gc->parent),
"Ignoring %u default trigger\n", type);
type = IRQ_TYPE_NONE;
}
gc->to_irq = gpiochip_to_irq;
gc->irq.default_type = type;
gc->irq.lock_key = lock_key;
gc->irq.request_key = request_key;
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
/* If a parent irqdomain is provided, let's build a hierarchy */
if (gpiochip_hierarchy_is_hierarchical(gc)) {
int ret = gpiochip_hierarchy_add_domain(gc);
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
if (ret)
return ret;
} else {
/* Some drivers provide custom irqdomain ops */
if (gc->irq.domain_ops)
ops = gc->irq.domain_ops;
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
if (!ops)
ops = &gpiochip_domain_ops;
gc->irq.domain = irq_domain_add_simple(np,
gc->ngpio,
gc->irq.first,
ops, gc);
if (!gc->irq.domain)
gpio: Add support for hierarchical IRQ domains Hierarchical IRQ domains can be used to stack different IRQ controllers on top of each other. Bring hierarchical IRQ domains into the GPIOLIB core with the following basic idea: Drivers that need their interrupts handled hierarchically specify a callback to translate the child hardware IRQ and IRQ type for each GPIO offset to a parent hardware IRQ and parent hardware IRQ type. Users have to pass the callback, fwnode, and parent irqdomain before calling gpiochip_irqchip_add(). We use the new method of just filling in the struct gpio_irq_chip before adding the gpiochip for all hierarchical irqchips of this type. The code path for device tree is pretty straight-forward, while the code path for old boardfiles or anything else will be more convoluted requireing upfront allocation of the interrupts when adding the chip. One specific use-case where this can be useful is if a power management controller has top-level controls for wakeup interrupts. In such cases, the power management controller can be a parent to other interrupt controllers and program additional registers when an IRQ has its wake capability enabled or disabled. The hierarchical irqchip helper code will only be available when IRQ_DOMAIN_HIERARCHY is selected to GPIO chips using this should select or depend on that symbol. When using hierarchical IRQs, the parent interrupt controller must also be hierarchical all the way up to the top interrupt controller wireing directly into the CPU, so on systems that do not have this we can get rid of all the extra code for supporting hierarchical irqs. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Lina Iyer <ilina@codeaurora.org> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Sowjanya Komatineni <skomatineni@nvidia.com> Cc: Bitan Biswas <bbiswas@nvidia.com> Cc: linux-tegra@vger.kernel.org Cc: David Daney <david.daney@cavium.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Brian Masney <masneyb@onstation.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Brian Masney <masneyb@onstation.org> Co-developed-by: Brian Masney <masneyb@onstation.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20190808123242.5359-1-linus.walleij@linaro.org
2019-08-08 12:32:37 +00:00
return -EINVAL;
}
if (gc->irq.parent_handler) {
void *data = gc->irq.parent_handler_data ?: gc;
for (i = 0; i < gc->irq.num_parents; i++) {
/*
* The parent IRQ chip is already using the chip_data
* for this IRQ chip, so our callbacks simply use the
* handler_data.
*/
irq_set_chained_handler_and_data(gc->irq.parents[i],
gc->irq.parent_handler,
data);
}
}
gpiochip_set_irq_hooks(gc);
acpi_gpiochip_request_interrupts(gc);
return 0;
}
/**
* gpiochip_irqchip_remove() - removes an irqchip added to a gpiochip
* @gc: the gpiochip to remove the irqchip from
*
* This is called only from gpiochip_remove()
*/
static void gpiochip_irqchip_remove(struct gpio_chip *gc)
{
struct irq_chip *irqchip = gc->irq.chip;
unsigned int offset;
acpi_gpiochip_free_interrupts(gc);
if (irqchip && gc->irq.parent_handler) {
struct gpio_irq_chip *irq = &gc->irq;
unsigned int i;
for (i = 0; i < irq->num_parents; i++)
irq_set_chained_handler_and_data(irq->parents[i],
NULL, NULL);
}
/* Remove all IRQ mappings and delete the domain */
if (gc->irq.domain) {
unsigned int irq;
for (offset = 0; offset < gc->ngpio; offset++) {
if (!gpiochip_irqchip_irq_valid(gc, offset))
continue;
irq = irq_find_mapping(gc->irq.domain, offset);
irq_dispose_mapping(irq);
}
irq_domain_remove(gc->irq.domain);
}
if (irqchip) {
if (irqchip->irq_request_resources == gpiochip_irq_reqres) {
irqchip->irq_request_resources = NULL;
irqchip->irq_release_resources = NULL;
}
if (irqchip->irq_enable == gpiochip_irq_enable) {
irqchip->irq_enable = gc->irq.irq_enable;
irqchip->irq_disable = gc->irq.irq_disable;
}
}
gc->irq.irq_enable = NULL;
gc->irq.irq_disable = NULL;
gc->irq.chip = NULL;
gpiochip_irqchip_free_valid_mask(gc);
}
/**
* gpiochip_irqchip_add_domain() - adds an irqdomain to a gpiochip
* @gc: the gpiochip to add the irqchip to
* @domain: the irqdomain to add to the gpiochip
*
* This function adds an IRQ domain to the gpiochip.
*/
int gpiochip_irqchip_add_domain(struct gpio_chip *gc,
struct irq_domain *domain)
{
if (!domain)
return -EINVAL;
gc->to_irq = gpiochip_to_irq;
gc->irq.domain = domain;
return 0;
}
EXPORT_SYMBOL_GPL(gpiochip_irqchip_add_domain);
#else /* CONFIG_GPIOLIB_IRQCHIP */
static inline int gpiochip_add_irqchip(struct gpio_chip *gc,
struct lock_class_key *lock_key,
struct lock_class_key *request_key)
{
return 0;
}
static void gpiochip_irqchip_remove(struct gpio_chip *gc) {}
static inline int gpiochip_irqchip_init_hw(struct gpio_chip *gc)
{
return 0;
}
static inline int gpiochip_irqchip_init_valid_mask(struct gpio_chip *gc)
{
return 0;
}
static inline void gpiochip_irqchip_free_valid_mask(struct gpio_chip *gc)
{ }
#endif /* CONFIG_GPIOLIB_IRQCHIP */
/**
* gpiochip_generic_request() - request the gpio function for a pin
* @gc: the gpiochip owning the GPIO
* @offset: the offset of the GPIO to request for GPIO function
*/
int gpiochip_generic_request(struct gpio_chip *gc, unsigned int offset)
{
#ifdef CONFIG_PINCTRL
if (list_empty(&gc->gpiodev->pin_ranges))
return 0;
#endif
return pinctrl_gpio_request(gc->gpiodev->base + offset);
}
EXPORT_SYMBOL_GPL(gpiochip_generic_request);
/**
* gpiochip_generic_free() - free the gpio function from a pin
* @gc: the gpiochip to request the gpio function for
* @offset: the offset of the GPIO to free from GPIO function
*/
void gpiochip_generic_free(struct gpio_chip *gc, unsigned int offset)
{
pinctrl_gpio_free(gc->gpiodev->base + offset);
}
EXPORT_SYMBOL_GPL(gpiochip_generic_free);
/**
* gpiochip_generic_config() - apply configuration for a pin
* @gc: the gpiochip owning the GPIO
* @offset: the offset of the GPIO to apply the configuration
* @config: the configuration to be applied
*/
int gpiochip_generic_config(struct gpio_chip *gc, unsigned int offset,
unsigned long config)
{
return pinctrl_gpio_set_config(gc->gpiodev->base + offset, config);
}
EXPORT_SYMBOL_GPL(gpiochip_generic_config);
#ifdef CONFIG_PINCTRL
/**
* gpiochip_add_pingroup_range() - add a range for GPIO <-> pin mapping
* @gc: the gpiochip to add the range for
* @pctldev: the pin controller to map to
* @gpio_offset: the start offset in the current gpio_chip number space
* @pin_group: name of the pin group inside the pin controller
*
* Calling this function directly from a DeviceTree-supported
* pinctrl driver is DEPRECATED. Please see Section 2.1 of
* Documentation/devicetree/bindings/gpio/gpio.txt on how to
* bind pinctrl and gpio drivers via the "gpio-ranges" property.
*/
int gpiochip_add_pingroup_range(struct gpio_chip *gc,
struct pinctrl_dev *pctldev,
unsigned int gpio_offset, const char *pin_group)
{
struct gpio_pin_range *pin_range;
struct gpio_device *gdev = gc->gpiodev;
int ret;
pin_range = kzalloc(sizeof(*pin_range), GFP_KERNEL);
if (!pin_range) {
chip_err(gc, "failed to allocate pin ranges\n");
return -ENOMEM;
}
/* Use local offset as range ID */
pin_range->range.id = gpio_offset;
pin_range->range.gc = gc;
pin_range->range.name = gc->label;
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
pin_range->range.base = gdev->base + gpio_offset;
pin_range->pctldev = pctldev;
ret = pinctrl_get_group_pins(pctldev, pin_group,
&pin_range->range.pins,
&pin_range->range.npins);
if (ret < 0) {
kfree(pin_range);
return ret;
}
pinctrl_add_gpio_range(pctldev, &pin_range->range);
chip_dbg(gc, "created GPIO range %d->%d ==> %s PINGRP %s\n",
gpio_offset, gpio_offset + pin_range->range.npins - 1,
pinctrl_dev_get_devname(pctldev), pin_group);
list_add_tail(&pin_range->node, &gdev->pin_ranges);
return 0;
}
EXPORT_SYMBOL_GPL(gpiochip_add_pingroup_range);
/**
* gpiochip_add_pin_range() - add a range for GPIO <-> pin mapping
* @gc: the gpiochip to add the range for
* @pinctl_name: the dev_name() of the pin controller to map to
* @gpio_offset: the start offset in the current gpio_chip number space
* @pin_offset: the start offset in the pin controller number space
* @npins: the number of pins from the offset of each pin space (GPIO and
* pin controller) to accumulate in this range
*
* Returns:
* 0 on success, or a negative error-code on failure.
*
* Calling this function directly from a DeviceTree-supported
* pinctrl driver is DEPRECATED. Please see Section 2.1 of
* Documentation/devicetree/bindings/gpio/gpio.txt on how to
* bind pinctrl and gpio drivers via the "gpio-ranges" property.
*/
int gpiochip_add_pin_range(struct gpio_chip *gc, const char *pinctl_name,
unsigned int gpio_offset, unsigned int pin_offset,
unsigned int npins)
{
struct gpio_pin_range *pin_range;
struct gpio_device *gdev = gc->gpiodev;
int ret;
pin_range = kzalloc(sizeof(*pin_range), GFP_KERNEL);
if (!pin_range) {
chip_err(gc, "failed to allocate pin ranges\n");
return -ENOMEM;
}
/* Use local offset as range ID */
pin_range->range.id = gpio_offset;
pin_range->range.gc = gc;
pin_range->range.name = gc->label;
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
pin_range->range.base = gdev->base + gpio_offset;
pin_range->range.pin_base = pin_offset;
pin_range->range.npins = npins;
pin_range->pctldev = pinctrl_find_and_add_gpio_range(pinctl_name,
&pin_range->range);
if (IS_ERR(pin_range->pctldev)) {
ret = PTR_ERR(pin_range->pctldev);
chip_err(gc, "could not create pin range\n");
kfree(pin_range);
return ret;
}
chip_dbg(gc, "created GPIO range %d->%d ==> %s PIN %d->%d\n",
gpio_offset, gpio_offset + npins - 1,
pinctl_name,
pin_offset, pin_offset + npins - 1);
list_add_tail(&pin_range->node, &gdev->pin_ranges);
return 0;
}
EXPORT_SYMBOL_GPL(gpiochip_add_pin_range);
/**
* gpiochip_remove_pin_ranges() - remove all the GPIO <-> pin mappings
* @gc: the chip to remove all the mappings for
*/
void gpiochip_remove_pin_ranges(struct gpio_chip *gc)
{
struct gpio_pin_range *pin_range, *tmp;
struct gpio_device *gdev = gc->gpiodev;
list_for_each_entry_safe(pin_range, tmp, &gdev->pin_ranges, node) {
list_del(&pin_range->node);
pinctrl_remove_gpio_range(pin_range->pctldev,
&pin_range->range);
kfree(pin_range);
}
}
EXPORT_SYMBOL_GPL(gpiochip_remove_pin_ranges);
#endif /* CONFIG_PINCTRL */
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/* These "optional" allocation calls help prevent drivers from stomping
* on each other, and help provide better diagnostics in debugfs.
* They're called even less than the "set direction" calls.
*/
static int gpiod_request_commit(struct gpio_desc *desc, const char *label)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
struct gpio_chip *gc = desc->gdev->chip;
int ret;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
unsigned long flags;
unsigned offset;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
if (label) {
label = kstrdup_const(label, GFP_KERNEL);
if (!label)
return -ENOMEM;
}
spin_lock_irqsave(&gpio_lock, flags);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/* NOTE: gpio_request() can be called in early boot,
* before IRQs are enabled, for non-sleeping (SOC) GPIOs.
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*/
if (test_and_set_bit(FLAG_REQUESTED, &desc->flags) == 0) {
desc_set_label(desc, label ? : "?");
ret = 0;
} else {
kfree_const(label);
ret = -EBUSY;
goto done;
}
if (gc->request) {
/* gc->request may sleep */
spin_unlock_irqrestore(&gpio_lock, flags);
offset = gpio_chip_hwgpio(desc);
if (gpiochip_line_is_valid(gc, offset))
ret = gc->request(gc, offset);
else
ret = -EINVAL;
spin_lock_irqsave(&gpio_lock, flags);
if (ret < 0) {
desc_set_label(desc, NULL);
kfree_const(label);
clear_bit(FLAG_REQUESTED, &desc->flags);
goto done;
}
}
if (gc->get_direction) {
/* gc->get_direction may sleep */
spin_unlock_irqrestore(&gpio_lock, flags);
gpiod_get_direction(desc);
spin_lock_irqsave(&gpio_lock, flags);
}
done:
spin_unlock_irqrestore(&gpio_lock, flags);
return ret;
}
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
/*
* This descriptor validation needs to be inserted verbatim into each
* function taking a descriptor, so we need to use a preprocessor
* macro to avoid endless duplication. If the desc is NULL it is an
* optional GPIO and calls should just bail out.
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
*/
static int validate_desc(const struct gpio_desc *desc, const char *func)
{
if (!desc)
return 0;
if (IS_ERR(desc)) {
pr_warn("%s: invalid GPIO (errorpointer)\n", func);
return PTR_ERR(desc);
}
if (!desc->gdev) {
pr_warn("%s: invalid GPIO (no device)\n", func);
return -EINVAL;
}
if (!desc->gdev->chip) {
dev_warn(&desc->gdev->dev,
"%s: backing chip is gone\n", func);
return 0;
}
return 1;
}
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
#define VALIDATE_DESC(desc) do { \
int __valid = validate_desc(desc, __func__); \
if (__valid <= 0) \
return __valid; \
} while (0)
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
#define VALIDATE_DESC_VOID(desc) do { \
int __valid = validate_desc(desc, __func__); \
if (__valid <= 0) \
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
return; \
} while (0)
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
int gpiod_request(struct gpio_desc *desc, const char *label)
{
int ret = -EPROBE_DEFER;
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
struct gpio_device *gdev;
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC(desc);
gdev = desc->gdev;
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
if (try_module_get(gdev->owner)) {
ret = gpiod_request_commit(desc, label);
if (ret < 0)
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
module_put(gdev->owner);
else
get_device(&gdev->dev);
}
if (ret)
gpiod_dbg(desc, "%s: status %d\n", __func__, ret);
return ret;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
static bool gpiod_free_commit(struct gpio_desc *desc)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
bool ret = false;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
unsigned long flags;
struct gpio_chip *gc;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
might_sleep();
gpiod_unexport(desc);
gpio: sysfs interface This adds a simple sysfs interface for GPIOs. /sys/class/gpio /export ... asks the kernel to export a GPIO to userspace /unexport ... to return a GPIO to the kernel /gpioN ... for each exported GPIO #N /value ... always readable, writes fail for input GPIOs /direction ... r/w as: in, out (default low); write high, low /gpiochipN ... for each gpiochip; #N is its first GPIO /base ... (r/o) same as N /label ... (r/o) descriptive, not necessarily unique /ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1) GPIOs claimed by kernel code may be exported by its owner using a new gpio_export() call, which should be most useful for driver debugging. Such exports may optionally be done without a "direction" attribute. Userspace may ask to take over a GPIO by writing to a sysfs control file, helping to cope with incomplete board support or other "one-off" requirements that don't merit full kernel support: echo 23 > /sys/class/gpio/export ... will gpio_request(23, "sysfs") and gpio_export(23); use /sys/class/gpio/gpio-23/direction to (re)configure it, when that GPIO can be used as both input and output. echo 23 > /sys/class/gpio/unexport ... will gpio_free(23), when it was exported as above The extra D-space footprint is a few hundred bytes, except for the sysfs resources associated with each exported GPIO. The additional I-space footprint is about two thirds of the current size of gpiolib (!). Since no /dev node creation is involved, no "udev" support is needed. Related changes: * This adds a device pointer to "struct gpio_chip". When GPIO providers initialize that, sysfs gpio class devices become children of that device instead of being "virtual" devices. * The (few) gpio_chip providers which have such a device node have been updated. * Some gpio_chip drivers also needed to update their module "owner" field ... for which missing kerneldoc was added. * Some gpio_chips don't support input GPIOs. Those GPIOs are now flagged appropriately when the chip is registered. Based on previous patches, and discussion both on and off LKML. A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this merges to mainline. [akpm@linux-foundation.org: a few maintenance build fixes] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Cc: Greg KH <greg@kroah.com> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-25 08:46:07 +00:00
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
spin_lock_irqsave(&gpio_lock, flags);
gc = desc->gdev->chip;
if (gc && test_bit(FLAG_REQUESTED, &desc->flags)) {
if (gc->free) {
spin_unlock_irqrestore(&gpio_lock, flags);
might_sleep_if(gc->can_sleep);
gc->free(gc, gpio_chip_hwgpio(desc));
spin_lock_irqsave(&gpio_lock, flags);
}
kfree_const(desc->label);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
desc_set_label(desc, NULL);
clear_bit(FLAG_ACTIVE_LOW, &desc->flags);
clear_bit(FLAG_REQUESTED, &desc->flags);
clear_bit(FLAG_OPEN_DRAIN, &desc->flags);
clear_bit(FLAG_OPEN_SOURCE, &desc->flags);
clear_bit(FLAG_PULL_UP, &desc->flags);
clear_bit(FLAG_PULL_DOWN, &desc->flags);
clear_bit(FLAG_BIAS_DISABLE, &desc->flags);
clear_bit(FLAG_EDGE_RISING, &desc->flags);
clear_bit(FLAG_EDGE_FALLING, &desc->flags);
clear_bit(FLAG_IS_HOGGED, &desc->flags);
#ifdef CONFIG_OF_DYNAMIC
desc->hog = NULL;
#endif
#ifdef CONFIG_GPIO_CDEV
WRITE_ONCE(desc->debounce_period_us, 0);
#endif
ret = true;
}
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
spin_unlock_irqrestore(&gpio_lock, flags);
blocking_notifier_call_chain(&desc->gdev->notifier,
GPIOLINE_CHANGED_RELEASED, desc);
return ret;
}
void gpiod_free(struct gpio_desc *desc)
{
if (desc && desc->gdev && gpiod_free_commit(desc)) {
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
module_put(desc->gdev->owner);
put_device(&desc->gdev->dev);
} else {
WARN_ON(extra_checks);
}
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiochip_is_requested - return string iff signal was requested
* @gc: controller managing the signal
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
* @offset: of signal within controller's 0..(ngpio - 1) range
*
* Returns NULL if the GPIO is not currently requested, else a string.
* The string returned is the label passed to gpio_request(); if none has been
* passed it is a meaningless, non-NULL constant.
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*
* This function is for use by GPIO controller drivers. The label can
* help with diagnostics, and knowing that the signal is used as a GPIO
* can help avoid accidentally multiplexing it to another controller.
*/
const char *gpiochip_is_requested(struct gpio_chip *gc, unsigned int offset)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
struct gpio_desc *desc;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
if (offset >= gc->ngpio)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
return NULL;
desc = gpiochip_get_desc(gc, offset);
if (IS_ERR(desc))
return NULL;
if (test_bit(FLAG_REQUESTED, &desc->flags) == 0)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
return NULL;
return desc->label;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
EXPORT_SYMBOL_GPL(gpiochip_is_requested);
/**
* gpiochip_request_own_desc - Allow GPIO chip to request its own descriptor
* @gc: GPIO chip
* @hwnum: hardware number of the GPIO for which to request the descriptor
* @label: label for the GPIO
* @lflags: lookup flags for this GPIO or 0 if default, this can be used to
* specify things like line inversion semantics with the machine flags
* such as GPIO_OUT_LOW
* @dflags: descriptor request flags for this GPIO or 0 if default, this
* can be used to specify consumer semantics such as open drain
*
* Function allows GPIO chip drivers to request and use their own GPIO
* descriptors via gpiolib API. Difference to gpiod_request() is that this
* function will not increase reference count of the GPIO chip module. This
* allows the GPIO chip module to be unloaded as needed (we assume that the
* GPIO chip driver handles freeing the GPIOs it has requested).
*
* Returns:
* A pointer to the GPIO descriptor, or an ERR_PTR()-encoded negative error
* code on failure.
*/
struct gpio_desc *gpiochip_request_own_desc(struct gpio_chip *gc,
unsigned int hwnum,
const char *label,
enum gpio_lookup_flags lflags,
enum gpiod_flags dflags)
{
struct gpio_desc *desc = gpiochip_get_desc(gc, hwnum);
int ret;
if (IS_ERR(desc)) {
chip_err(gc, "failed to get GPIO descriptor\n");
return desc;
}
ret = gpiod_request_commit(desc, label);
if (ret < 0)
return ERR_PTR(ret);
ret = gpiod_configure_flags(desc, label, lflags, dflags);
if (ret) {
chip_err(gc, "setup of own GPIO %s failed\n", label);
gpiod_free_commit(desc);
return ERR_PTR(ret);
}
return desc;
}
EXPORT_SYMBOL_GPL(gpiochip_request_own_desc);
/**
* gpiochip_free_own_desc - Free GPIO requested by the chip driver
* @desc: GPIO descriptor to free
*
* Function frees the given GPIO requested previously with
* gpiochip_request_own_desc().
*/
void gpiochip_free_own_desc(struct gpio_desc *desc)
{
if (desc)
gpiod_free_commit(desc);
}
EXPORT_SYMBOL_GPL(gpiochip_free_own_desc);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
/*
* Drivers MUST set GPIO direction before making get/set calls. In
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
* some cases this is done in early boot, before IRQs are enabled.
*
* As a rule these aren't called more than once (except for drivers
* using the open-drain emulation idiom) so these are natural places
* to accumulate extra debugging checks. Note that we can't (yet)
* rely on gpio_request() having been called beforehand.
*/
static int gpio_do_set_config(struct gpio_chip *gc, unsigned int offset,
unsigned long config)
{
if (!gc->set_config)
return -ENOTSUPP;
return gc->set_config(gc, offset, config);
}
static int gpio_set_config(struct gpio_desc *desc, enum pin_config_param mode)
{
struct gpio_chip *gc = desc->gdev->chip;
unsigned long config;
unsigned int arg;
switch (mode) {
case PIN_CONFIG_BIAS_PULL_DOWN:
case PIN_CONFIG_BIAS_PULL_UP:
arg = 1;
break;
default:
arg = 0;
break;
}
config = pinconf_to_config_packed(mode, arg);
return gpio_do_set_config(gc, gpio_chip_hwgpio(desc), config);
}
static int gpio_set_bias(struct gpio_desc *desc)
{
enum pin_config_param bias;
int ret;
if (test_bit(FLAG_BIAS_DISABLE, &desc->flags))
bias = PIN_CONFIG_BIAS_DISABLE;
else if (test_bit(FLAG_PULL_UP, &desc->flags))
bias = PIN_CONFIG_BIAS_PULL_UP;
else if (test_bit(FLAG_PULL_DOWN, &desc->flags))
bias = PIN_CONFIG_BIAS_PULL_DOWN;
else
return 0;
ret = gpio_set_config(desc, bias);
if (ret != -ENOTSUPP)
return ret;
return 0;
}
/**
* gpiod_direction_input - set the GPIO direction to input
* @desc: GPIO to set to input
*
* Set the direction of the passed GPIO to input, such as gpiod_get_value() can
* be called safely on it.
*
* Return 0 in case of success, else an error code.
*/
int gpiod_direction_input(struct gpio_desc *desc)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
struct gpio_chip *gc;
int ret = 0;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC(desc);
gc = desc->gdev->chip;
/*
* It is legal to have no .get() and .direction_input() specified if
* the chip is output-only, but you can't specify .direction_input()
* and not support the .get() operation, that doesn't make sense.
*/
if (!gc->get && gc->direction_input) {
gpiod_warn(desc,
"%s: missing get() but have direction_input()\n",
__func__);
return -EIO;
}
/*
* If we have a .direction_input() callback, things are simple,
* just call it. Else we are some input-only chip so try to check the
* direction (if .get_direction() is supported) else we silently
* assume we are in input mode after this.
*/
if (gc->direction_input) {
ret = gc->direction_input(gc, gpio_chip_hwgpio(desc));
} else if (gc->get_direction &&
(gc->get_direction(gc, gpio_chip_hwgpio(desc)) != 1)) {
gpiod_warn(desc,
"%s: missing direction_input() operation and line is output\n",
__func__);
return -EIO;
}
if (ret == 0) {
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
clear_bit(FLAG_IS_OUT, &desc->flags);
ret = gpio_set_bias(desc);
}
trace_gpio_direction(desc_to_gpio(desc), 1, ret);
return ret;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
EXPORT_SYMBOL_GPL(gpiod_direction_input);
static int gpiod_direction_output_raw_commit(struct gpio_desc *desc, int value)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
struct gpio_chip *gc = desc->gdev->chip;
int val = !!value;
int ret = 0;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/*
* It's OK not to specify .direction_output() if the gpiochip is
* output-only, but if there is then not even a .set() operation it
* is pretty tricky to drive the output line.
*/
if (!gc->set && !gc->direction_output) {
gpiod_warn(desc,
"%s: missing set() and direction_output() operations\n",
__func__);
return -EIO;
}
if (gc->direction_output) {
ret = gc->direction_output(gc, gpio_chip_hwgpio(desc), val);
} else {
/* Check that we are in output mode if we can */
if (gc->get_direction &&
gc->get_direction(gc, gpio_chip_hwgpio(desc))) {
gpiod_warn(desc,
"%s: missing direction_output() operation\n",
__func__);
return -EIO;
}
/*
* If we can't actively set the direction, we are some
* output-only chip, so just drive the output as desired.
*/
gc->set(gc, gpio_chip_hwgpio(desc), val);
}
if (!ret)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
set_bit(FLAG_IS_OUT, &desc->flags);
trace_gpio_value(desc_to_gpio(desc), 0, val);
trace_gpio_direction(desc_to_gpio(desc), 0, ret);
return ret;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
/**
* gpiod_direction_output_raw - set the GPIO direction to output
* @desc: GPIO to set to output
* @value: initial output value of the GPIO
*
* Set the direction of the passed GPIO to output, such as gpiod_set_value() can
* be called safely on it. The initial value of the output must be specified
* as raw value on the physical line without regard for the ACTIVE_LOW status.
*
* Return 0 in case of success, else an error code.
*/
int gpiod_direction_output_raw(struct gpio_desc *desc, int value)
{
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC(desc);
return gpiod_direction_output_raw_commit(desc, value);
}
EXPORT_SYMBOL_GPL(gpiod_direction_output_raw);
/**
* gpiod_direction_output - set the GPIO direction to output
* @desc: GPIO to set to output
* @value: initial output value of the GPIO
*
* Set the direction of the passed GPIO to output, such as gpiod_set_value() can
* be called safely on it. The initial value of the output must be specified
* as the logical value of the GPIO, i.e. taking its ACTIVE_LOW status into
* account.
*
* Return 0 in case of success, else an error code.
*/
int gpiod_direction_output(struct gpio_desc *desc, int value)
{
int ret;
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC(desc);
if (test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
else
value = !!value;
/* GPIOs used for enabled IRQs shall not be set as output */
if (test_bit(FLAG_USED_AS_IRQ, &desc->flags) &&
test_bit(FLAG_IRQ_IS_ENABLED, &desc->flags)) {
gpiod_err(desc,
"%s: tried to set a GPIO tied to an IRQ as output\n",
__func__);
return -EIO;
}
if (test_bit(FLAG_OPEN_DRAIN, &desc->flags)) {
/* First see if we can enable open drain in hardware */
ret = gpio_set_config(desc, PIN_CONFIG_DRIVE_OPEN_DRAIN);
if (!ret)
goto set_output_value;
/* Emulate open drain by not actively driving the line high */
if (value) {
ret = gpiod_direction_input(desc);
goto set_output_flag;
}
}
else if (test_bit(FLAG_OPEN_SOURCE, &desc->flags)) {
ret = gpio_set_config(desc, PIN_CONFIG_DRIVE_OPEN_SOURCE);
if (!ret)
goto set_output_value;
/* Emulate open source by not actively driving the line low */
if (!value) {
ret = gpiod_direction_input(desc);
goto set_output_flag;
}
} else {
gpio_set_config(desc, PIN_CONFIG_DRIVE_PUSH_PULL);
}
set_output_value:
ret = gpio_set_bias(desc);
if (ret)
return ret;
return gpiod_direction_output_raw_commit(desc, value);
set_output_flag:
/*
* When emulating open-source or open-drain functionalities by not
* actively driving the line (setting mode to input) we still need to
* set the IS_OUT flag or otherwise we won't be able to set the line
* value anymore.
*/
if (ret == 0)
set_bit(FLAG_IS_OUT, &desc->flags);
return ret;
}
EXPORT_SYMBOL_GPL(gpiod_direction_output);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiod_set_config - sets @config for a GPIO
* @desc: descriptor of the GPIO for which to set the configuration
* @config: Same packed config format as generic pinconf
*
* Returns:
* 0 on success, %-ENOTSUPP if the controller doesn't support setting the
* configuration.
*/
int gpiod_set_config(struct gpio_desc *desc, unsigned long config)
{
struct gpio_chip *gc;
VALIDATE_DESC(desc);
gc = desc->gdev->chip;
return gpio_do_set_config(gc, gpio_chip_hwgpio(desc), config);
}
EXPORT_SYMBOL_GPL(gpiod_set_config);
2010-05-26 21:42:23 +00:00
/**
* gpiod_set_debounce - sets @debounce time for a GPIO
* @desc: descriptor of the GPIO for which to set debounce time
* @debounce: debounce time in microseconds
*
* Returns:
* 0 on success, %-ENOTSUPP if the controller doesn't support setting the
* debounce time.
2010-05-26 21:42:23 +00:00
*/
int gpiod_set_debounce(struct gpio_desc *desc, unsigned int debounce)
2010-05-26 21:42:23 +00:00
{
unsigned long config;
config = pinconf_to_config_packed(PIN_CONFIG_INPUT_DEBOUNCE, debounce);
return gpiod_set_config(desc, config);
2010-05-26 21:42:23 +00:00
}
EXPORT_SYMBOL_GPL(gpiod_set_debounce);
/**
* gpiod_set_transitory - Lose or retain GPIO state on suspend or reset
* @desc: descriptor of the GPIO for which to configure persistence
* @transitory: True to lose state on suspend or reset, false for persistence
*
* Returns:
* 0 on success, otherwise a negative error code.
*/
int gpiod_set_transitory(struct gpio_desc *desc, bool transitory)
{
struct gpio_chip *gc;
unsigned long packed;
int gpio;
int rc;
VALIDATE_DESC(desc);
/*
* Handle FLAG_TRANSITORY first, enabling queries to gpiolib for
* persistence state.
*/
assign_bit(FLAG_TRANSITORY, &desc->flags, transitory);
/* If the driver supports it, set the persistence state now */
gc = desc->gdev->chip;
if (!gc->set_config)
return 0;
packed = pinconf_to_config_packed(PIN_CONFIG_PERSIST_STATE,
!transitory);
gpio = gpio_chip_hwgpio(desc);
rc = gpio_do_set_config(gc, gpio, packed);
if (rc == -ENOTSUPP) {
dev_dbg(&desc->gdev->dev, "Persistence not supported for GPIO %d\n",
gpio);
return 0;
}
return rc;
}
EXPORT_SYMBOL_GPL(gpiod_set_transitory);
/**
* gpiod_is_active_low - test whether a GPIO is active-low or not
* @desc: the gpio descriptor to test
*
* Returns 1 if the GPIO is active-low, 0 otherwise.
*/
int gpiod_is_active_low(const struct gpio_desc *desc)
{
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC(desc);
return test_bit(FLAG_ACTIVE_LOW, &desc->flags);
}
EXPORT_SYMBOL_GPL(gpiod_is_active_low);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiod_toggle_active_low - toggle whether a GPIO is active-low or not
* @desc: the gpio descriptor to change
*/
void gpiod_toggle_active_low(struct gpio_desc *desc)
{
VALIDATE_DESC_VOID(desc);
change_bit(FLAG_ACTIVE_LOW, &desc->flags);
}
EXPORT_SYMBOL_GPL(gpiod_toggle_active_low);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/* I/O calls are only valid after configuration completed; the relevant
* "is this a valid GPIO" error checks should already have been done.
*
* "Get" operations are often inlinable as reading a pin value register,
* and masking the relevant bit in that register.
*
* When "set" operations are inlinable, they involve writing that mask to
* one register to set a low value, or a different register to set it high.
* Otherwise locking is needed, so there may be little value to inlining.
*
*------------------------------------------------------------------------
*
* IMPORTANT!!! The hot paths -- get/set value -- assume that callers
* have requested the GPIO. That can include implicit requesting by
* a direction setting call. Marking a gpio as requested locks its chip
* in memory, guaranteeing that these table lookups need no more locking
* and that gpiochip_remove() will fail.
*
* REVISIT when debugging, consider adding some instrumentation to ensure
* that the GPIO was actually requested.
*/
static int gpiod_get_raw_value_commit(const struct gpio_desc *desc)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
struct gpio_chip *gc;
int offset;
int value;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
gc = desc->gdev->chip;
offset = gpio_chip_hwgpio(desc);
value = gc->get ? gc->get(gc, offset) : -EIO;
value = value < 0 ? value : !!value;
trace_gpio_value(desc_to_gpio(desc), 1, value);
return value;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
static int gpio_chip_get_multiple(struct gpio_chip *gc,
unsigned long *mask, unsigned long *bits)
{
if (gc->get_multiple) {
return gc->get_multiple(gc, mask, bits);
} else if (gc->get) {
int i, value;
for_each_set_bit(i, mask, gc->ngpio) {
value = gc->get(gc, i);
if (value < 0)
return value;
__assign_bit(i, bits, value);
}
return 0;
}
return -EIO;
}
int gpiod_get_array_value_complex(bool raw, bool can_sleep,
unsigned int array_size,
struct gpio_desc **desc_array,
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
struct gpio_array *array_info,
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
unsigned long *value_bitmap)
{
int ret, i = 0;
/*
* Validate array_info against desc_array and its size.
* It should immediately follow desc_array if both
* have been obtained from the same gpiod_get_array() call.
*/
if (array_info && array_info->desc == desc_array &&
array_size <= array_info->size &&
(void *)array_info == desc_array + array_info->size) {
if (!can_sleep)
WARN_ON(array_info->chip->can_sleep);
ret = gpio_chip_get_multiple(array_info->chip,
array_info->get_mask,
value_bitmap);
if (ret)
return ret;
if (!raw && !bitmap_empty(array_info->invert_mask, array_size))
bitmap_xor(value_bitmap, value_bitmap,
array_info->invert_mask, array_size);
i = find_first_zero_bit(array_info->get_mask, array_size);
if (i == array_size)
return 0;
} else {
array_info = NULL;
}
while (i < array_size) {
struct gpio_chip *gc = desc_array[i]->gdev->chip;
unsigned long fastpath[2 * BITS_TO_LONGS(FASTPATH_NGPIO)];
unsigned long *mask, *bits;
int first, j, ret;
if (likely(gc->ngpio <= FASTPATH_NGPIO)) {
mask = fastpath;
} else {
mask = kmalloc_array(2 * BITS_TO_LONGS(gc->ngpio),
sizeof(*mask),
can_sleep ? GFP_KERNEL : GFP_ATOMIC);
if (!mask)
return -ENOMEM;
}
bits = mask + BITS_TO_LONGS(gc->ngpio);
bitmap_zero(mask, gc->ngpio);
if (!can_sleep)
WARN_ON(gc->can_sleep);
/* collect all inputs belonging to the same chip */
first = i;
do {
const struct gpio_desc *desc = desc_array[i];
int hwgpio = gpio_chip_hwgpio(desc);
__set_bit(hwgpio, mask);
i++;
if (array_info)
i = find_next_zero_bit(array_info->get_mask,
array_size, i);
} while ((i < array_size) &&
(desc_array[i]->gdev->chip == gc));
ret = gpio_chip_get_multiple(gc, mask, bits);
if (ret) {
if (mask != fastpath)
kfree(mask);
return ret;
}
for (j = first; j < i; ) {
const struct gpio_desc *desc = desc_array[j];
int hwgpio = gpio_chip_hwgpio(desc);
int value = test_bit(hwgpio, bits);
if (!raw && test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
__assign_bit(j, value_bitmap, value);
trace_gpio_value(desc_to_gpio(desc), 1, value);
j++;
if (array_info)
j = find_next_zero_bit(array_info->get_mask, i,
j);
}
if (mask != fastpath)
kfree(mask);
}
return 0;
}
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiod_get_raw_value() - return a gpio's raw value
* @desc: gpio whose value will be returned
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*
* Return the GPIO's raw value, i.e. the value of the physical line disregarding
* its ACTIVE_LOW status, or negative errno on failure.
*
* This function can be called from contexts where we cannot sleep, and will
* complain if the GPIO chip functions potentially sleep.
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*/
int gpiod_get_raw_value(const struct gpio_desc *desc)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC(desc);
/* Should be using gpiod_get_raw_value_cansleep() */
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
WARN_ON(desc->gdev->chip->can_sleep);
return gpiod_get_raw_value_commit(desc);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
EXPORT_SYMBOL_GPL(gpiod_get_raw_value);
/**
* gpiod_get_value() - return a gpio's value
* @desc: gpio whose value will be returned
*
* Return the GPIO's logical value, i.e. taking the ACTIVE_LOW status into
* account, or negative errno on failure.
*
* This function can be called from contexts where we cannot sleep, and will
* complain if the GPIO chip functions potentially sleep.
*/
int gpiod_get_value(const struct gpio_desc *desc)
{
int value;
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC(desc);
/* Should be using gpiod_get_value_cansleep() */
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
WARN_ON(desc->gdev->chip->can_sleep);
value = gpiod_get_raw_value_commit(desc);
if (value < 0)
return value;
if (test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
return value;
}
EXPORT_SYMBOL_GPL(gpiod_get_value);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiod_get_raw_array_value() - read raw values from an array of GPIOs
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @array_size: number of elements in the descriptor array / value bitmap
* @desc_array: array of GPIO descriptors whose values will be read
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
* @array_info: information on applicability of fast bitmap processing path
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @value_bitmap: bitmap to store the read values
*
* Read the raw values of the GPIOs, i.e. the values of the physical lines
* without regard for their ACTIVE_LOW status. Return 0 in case of success,
* else an error code.
*
* This function can be called from contexts where we cannot sleep,
* and it will complain if the GPIO chip functions potentially sleep.
*/
int gpiod_get_raw_array_value(unsigned int array_size,
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
struct gpio_desc **desc_array,
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
struct gpio_array *array_info,
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
unsigned long *value_bitmap)
{
if (!desc_array)
return -EINVAL;
return gpiod_get_array_value_complex(true, false, array_size,
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
desc_array, array_info,
value_bitmap);
}
EXPORT_SYMBOL_GPL(gpiod_get_raw_array_value);
/**
* gpiod_get_array_value() - read values from an array of GPIOs
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @array_size: number of elements in the descriptor array / value bitmap
* @desc_array: array of GPIO descriptors whose values will be read
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
* @array_info: information on applicability of fast bitmap processing path
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @value_bitmap: bitmap to store the read values
*
* Read the logical values of the GPIOs, i.e. taking their ACTIVE_LOW status
* into account. Return 0 in case of success, else an error code.
*
* This function can be called from contexts where we cannot sleep,
* and it will complain if the GPIO chip functions potentially sleep.
*/
int gpiod_get_array_value(unsigned int array_size,
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
struct gpio_desc **desc_array,
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
struct gpio_array *array_info,
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
unsigned long *value_bitmap)
{
if (!desc_array)
return -EINVAL;
return gpiod_get_array_value_complex(false, false, array_size,
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
desc_array, array_info,
value_bitmap);
}
EXPORT_SYMBOL_GPL(gpiod_get_array_value);
/*
* gpio_set_open_drain_value_commit() - Set the open drain gpio's value.
* @desc: gpio descriptor whose state need to be set.
* @value: Non-zero for setting it HIGH otherwise it will set to LOW.
*/
static void gpio_set_open_drain_value_commit(struct gpio_desc *desc, bool value)
{
int ret = 0;
struct gpio_chip *gc = desc->gdev->chip;
int offset = gpio_chip_hwgpio(desc);
if (value) {
ret = gc->direction_input(gc, offset);
} else {
ret = gc->direction_output(gc, offset, 0);
if (!ret)
set_bit(FLAG_IS_OUT, &desc->flags);
}
trace_gpio_direction(desc_to_gpio(desc), value, ret);
if (ret < 0)
gpiod_err(desc,
"%s: Error in set_value for open drain err %d\n",
__func__, ret);
}
/*
* _gpio_set_open_source_value() - Set the open source gpio's value.
* @desc: gpio descriptor whose state need to be set.
* @value: Non-zero for setting it HIGH otherwise it will set to LOW.
*/
static void gpio_set_open_source_value_commit(struct gpio_desc *desc, bool value)
{
int ret = 0;
struct gpio_chip *gc = desc->gdev->chip;
int offset = gpio_chip_hwgpio(desc);
if (value) {
ret = gc->direction_output(gc, offset, 1);
if (!ret)
set_bit(FLAG_IS_OUT, &desc->flags);
} else {
ret = gc->direction_input(gc, offset);
}
trace_gpio_direction(desc_to_gpio(desc), !value, ret);
if (ret < 0)
gpiod_err(desc,
"%s: Error in set_value for open source err %d\n",
__func__, ret);
}
static void gpiod_set_raw_value_commit(struct gpio_desc *desc, bool value)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
struct gpio_chip *gc;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
gc = desc->gdev->chip;
trace_gpio_value(desc_to_gpio(desc), 0, value);
gc->set(gc, gpio_chip_hwgpio(desc), value);
}
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
/*
* set multiple outputs on the same chip;
* use the chip's set_multiple function if available;
* otherwise set the outputs sequentially;
* @chip: the GPIO chip we operate on
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
* @mask: bit mask array; one bit per output; BITS_PER_LONG bits per word
* defines which outputs are to be changed
* @bits: bit value array; one bit per output; BITS_PER_LONG bits per word
* defines the values the outputs specified by mask are to be set to
*/
static void gpio_chip_set_multiple(struct gpio_chip *gc,
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
unsigned long *mask, unsigned long *bits)
{
if (gc->set_multiple) {
gc->set_multiple(gc, mask, bits);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
} else {
unsigned int i;
/* set outputs if the corresponding mask bit is set */
for_each_set_bit(i, mask, gc->ngpio)
gc->set(gc, i, test_bit(i, bits));
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
}
}
int gpiod_set_array_value_complex(bool raw, bool can_sleep,
unsigned int array_size,
struct gpio_desc **desc_array,
struct gpio_array *array_info,
unsigned long *value_bitmap)
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
{
int i = 0;
/*
* Validate array_info against desc_array and its size.
* It should immediately follow desc_array if both
* have been obtained from the same gpiod_get_array() call.
*/
if (array_info && array_info->desc == desc_array &&
array_size <= array_info->size &&
(void *)array_info == desc_array + array_info->size) {
if (!can_sleep)
WARN_ON(array_info->chip->can_sleep);
if (!raw && !bitmap_empty(array_info->invert_mask, array_size))
bitmap_xor(value_bitmap, value_bitmap,
array_info->invert_mask, array_size);
gpio_chip_set_multiple(array_info->chip, array_info->set_mask,
value_bitmap);
i = find_first_zero_bit(array_info->set_mask, array_size);
if (i == array_size)
return 0;
} else {
array_info = NULL;
}
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
while (i < array_size) {
struct gpio_chip *gc = desc_array[i]->gdev->chip;
unsigned long fastpath[2 * BITS_TO_LONGS(FASTPATH_NGPIO)];
unsigned long *mask, *bits;
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
int count = 0;
if (likely(gc->ngpio <= FASTPATH_NGPIO)) {
mask = fastpath;
} else {
mask = kmalloc_array(2 * BITS_TO_LONGS(gc->ngpio),
sizeof(*mask),
can_sleep ? GFP_KERNEL : GFP_ATOMIC);
if (!mask)
return -ENOMEM;
}
bits = mask + BITS_TO_LONGS(gc->ngpio);
bitmap_zero(mask, gc->ngpio);
if (!can_sleep)
WARN_ON(gc->can_sleep);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
do {
struct gpio_desc *desc = desc_array[i];
int hwgpio = gpio_chip_hwgpio(desc);
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
int value = test_bit(i, value_bitmap);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
/*
* Pins applicable for fast input but not for
* fast output processing may have been already
* inverted inside the fast path, skip them.
*/
if (!raw && !(array_info &&
test_bit(i, array_info->invert_mask)) &&
test_bit(FLAG_ACTIVE_LOW, &desc->flags))
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
value = !value;
trace_gpio_value(desc_to_gpio(desc), 0, value);
/*
* collect all normal outputs belonging to the same chip
* open drain and open source outputs are set individually
*/
if (test_bit(FLAG_OPEN_DRAIN, &desc->flags) && !raw) {
gpio_set_open_drain_value_commit(desc, value);
} else if (test_bit(FLAG_OPEN_SOURCE, &desc->flags) && !raw) {
gpio_set_open_source_value_commit(desc, value);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
} else {
__set_bit(hwgpio, mask);
__assign_bit(hwgpio, bits, value);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
count++;
}
i++;
if (array_info)
i = find_next_zero_bit(array_info->set_mask,
array_size, i);
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
} while ((i < array_size) &&
(desc_array[i]->gdev->chip == gc));
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
/* push collected bits to outputs */
if (count != 0)
gpio_chip_set_multiple(gc, mask, bits);
if (mask != fastpath)
kfree(mask);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
}
return 0;
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
}
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiod_set_raw_value() - assign a gpio's raw value
* @desc: gpio whose value will be assigned
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
* @value: value to assign
*
* Set the raw value of the GPIO, i.e. the value of its physical line without
* regard for its ACTIVE_LOW status.
*
* This function can be called from contexts where we cannot sleep, and will
* complain if the GPIO chip functions potentially sleep.
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*/
void gpiod_set_raw_value(struct gpio_desc *desc, int value)
{
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC_VOID(desc);
/* Should be using gpiod_set_raw_value_cansleep() */
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
WARN_ON(desc->gdev->chip->can_sleep);
gpiod_set_raw_value_commit(desc, value);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
EXPORT_SYMBOL_GPL(gpiod_set_raw_value);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiod_set_value_nocheck() - set a GPIO line value without checking
* @desc: the descriptor to set the value on
* @value: value to set
*
* This sets the value of a GPIO line backing a descriptor, applying
* different semantic quirks like active low and open drain/source
* handling.
*/
static void gpiod_set_value_nocheck(struct gpio_desc *desc, int value)
{
if (test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
if (test_bit(FLAG_OPEN_DRAIN, &desc->flags))
gpio_set_open_drain_value_commit(desc, value);
else if (test_bit(FLAG_OPEN_SOURCE, &desc->flags))
gpio_set_open_source_value_commit(desc, value);
else
gpiod_set_raw_value_commit(desc, value);
}
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiod_set_value() - assign a gpio's value
* @desc: gpio whose value will be assigned
* @value: value to assign
*
* Set the logical value of the GPIO, i.e. taking its ACTIVE_LOW,
* OPEN_DRAIN and OPEN_SOURCE flags into account.
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*
* This function can be called from contexts where we cannot sleep, and will
* complain if the GPIO chip functions potentially sleep.
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*/
void gpiod_set_value(struct gpio_desc *desc, int value)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC_VOID(desc);
/* Should be using gpiod_set_value_cansleep() */
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
WARN_ON(desc->gdev->chip->can_sleep);
gpiod_set_value_nocheck(desc, value);
}
EXPORT_SYMBOL_GPL(gpiod_set_value);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
/**
* gpiod_set_raw_array_value() - assign values to an array of GPIOs
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @array_size: number of elements in the descriptor array / value bitmap
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
* @desc_array: array of GPIO descriptors whose values will be assigned
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
* @array_info: information on applicability of fast bitmap processing path
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @value_bitmap: bitmap of values to assign
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
*
* Set the raw values of the GPIOs, i.e. the values of the physical lines
* without regard for their ACTIVE_LOW status.
*
* This function can be called from contexts where we cannot sleep, and will
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
* complain if the GPIO chip functions potentially sleep.
*/
int gpiod_set_raw_array_value(unsigned int array_size,
struct gpio_desc **desc_array,
struct gpio_array *array_info,
unsigned long *value_bitmap)
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
{
if (!desc_array)
return -EINVAL;
return gpiod_set_array_value_complex(true, false, array_size,
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
desc_array, array_info, value_bitmap);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
}
EXPORT_SYMBOL_GPL(gpiod_set_raw_array_value);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
/**
* gpiod_set_array_value() - assign values to an array of GPIOs
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @array_size: number of elements in the descriptor array / value bitmap
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
* @desc_array: array of GPIO descriptors whose values will be assigned
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
* @array_info: information on applicability of fast bitmap processing path
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @value_bitmap: bitmap of values to assign
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
*
* Set the logical values of the GPIOs, i.e. taking their ACTIVE_LOW status
* into account.
*
* This function can be called from contexts where we cannot sleep, and will
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
* complain if the GPIO chip functions potentially sleep.
*/
int gpiod_set_array_value(unsigned int array_size,
struct gpio_desc **desc_array,
struct gpio_array *array_info,
unsigned long *value_bitmap)
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
{
if (!desc_array)
return -EINVAL;
return gpiod_set_array_value_complex(false, false, array_size,
desc_array, array_info,
value_bitmap);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
}
EXPORT_SYMBOL_GPL(gpiod_set_array_value);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiod_cansleep() - report whether gpio value access may sleep
* @desc: gpio to check
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*
*/
int gpiod_cansleep(const struct gpio_desc *desc)
{
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC(desc);
return desc->gdev->chip->can_sleep;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
EXPORT_SYMBOL_GPL(gpiod_cansleep);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiod_set_consumer_name() - set the consumer name for the descriptor
* @desc: gpio to set the consumer name on
* @name: the new consumer name
*/
int gpiod_set_consumer_name(struct gpio_desc *desc, const char *name)
{
VALIDATE_DESC(desc);
if (name) {
name = kstrdup_const(name, GFP_KERNEL);
if (!name)
return -ENOMEM;
}
kfree_const(desc->label);
desc_set_label(desc, name);
return 0;
}
EXPORT_SYMBOL_GPL(gpiod_set_consumer_name);
/**
* gpiod_to_irq() - return the IRQ corresponding to a GPIO
* @desc: gpio whose IRQ will be returned (already requested)
*
* Return the IRQ corresponding to the passed GPIO, or an error code in case of
* error.
*/
int gpiod_to_irq(const struct gpio_desc *desc)
{
struct gpio_chip *gc;
int offset;
/*
* Cannot VALIDATE_DESC() here as gpiod_to_irq() consumer semantics
* requires this function to not return zero on an invalid descriptor
* but rather a negative error number.
*/
if (!desc || IS_ERR(desc) || !desc->gdev || !desc->gdev->chip)
return -EINVAL;
gc = desc->gdev->chip;
offset = gpio_chip_hwgpio(desc);
if (gc->to_irq) {
int retirq = gc->to_irq(gc, offset);
/* Zero means NO_IRQ */
if (!retirq)
return -ENXIO;
return retirq;
}
return -ENXIO;
}
EXPORT_SYMBOL_GPL(gpiod_to_irq);
/**
* gpiochip_lock_as_irq() - lock a GPIO to be used as IRQ
* @gc: the chip the GPIO to lock belongs to
* @offset: the offset of the GPIO to lock as IRQ
*
* This is used directly by GPIO drivers that want to lock down
* a certain GPIO line to be used for IRQs.
*/
int gpiochip_lock_as_irq(struct gpio_chip *gc, unsigned int offset)
{
struct gpio_desc *desc;
desc = gpiochip_get_desc(gc, offset);
if (IS_ERR(desc))
return PTR_ERR(desc);
/*
* If it's fast: flush the direction setting if something changed
* behind our back
*/
if (!gc->can_sleep && gc->get_direction) {
int dir = gpiod_get_direction(desc);
if (dir < 0) {
chip_err(gc, "%s: cannot get GPIO direction\n",
__func__);
return dir;
}
}
/* To be valid for IRQ the line needs to be input or open drain */
if (test_bit(FLAG_IS_OUT, &desc->flags) &&
!test_bit(FLAG_OPEN_DRAIN, &desc->flags)) {
chip_err(gc,
"%s: tried to flag a GPIO set as output for IRQ\n",
__func__);
return -EIO;
}
set_bit(FLAG_USED_AS_IRQ, &desc->flags);
set_bit(FLAG_IRQ_IS_ENABLED, &desc->flags);
/*
* If the consumer has not set up a label (such as when the
* IRQ is referenced from .to_irq()) we set up a label here
* so it is clear this is used as an interrupt.
*/
if (!desc->label)
desc_set_label(desc, "interrupt");
return 0;
}
EXPORT_SYMBOL_GPL(gpiochip_lock_as_irq);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiochip_unlock_as_irq() - unlock a GPIO used as IRQ
* @gc: the chip the GPIO to lock belongs to
* @offset: the offset of the GPIO to lock as IRQ
*
* This is used directly by GPIO drivers that want to indicate
* that a certain GPIO is no longer used exclusively for IRQ.
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*/
void gpiochip_unlock_as_irq(struct gpio_chip *gc, unsigned int offset)
{
struct gpio_desc *desc;
desc = gpiochip_get_desc(gc, offset);
if (IS_ERR(desc))
return;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
clear_bit(FLAG_USED_AS_IRQ, &desc->flags);
clear_bit(FLAG_IRQ_IS_ENABLED, &desc->flags);
/* If we only had this marking, erase it */
if (desc->label && !strcmp(desc->label, "interrupt"))
desc_set_label(desc, NULL);
}
EXPORT_SYMBOL_GPL(gpiochip_unlock_as_irq);
void gpiochip_disable_irq(struct gpio_chip *gc, unsigned int offset)
{
struct gpio_desc *desc = gpiochip_get_desc(gc, offset);
if (!IS_ERR(desc) &&
!WARN_ON(!test_bit(FLAG_USED_AS_IRQ, &desc->flags)))
clear_bit(FLAG_IRQ_IS_ENABLED, &desc->flags);
}
EXPORT_SYMBOL_GPL(gpiochip_disable_irq);
void gpiochip_enable_irq(struct gpio_chip *gc, unsigned int offset)
{
struct gpio_desc *desc = gpiochip_get_desc(gc, offset);
if (!IS_ERR(desc) &&
!WARN_ON(!test_bit(FLAG_USED_AS_IRQ, &desc->flags))) {
/*
* We must not be output when using IRQ UNLESS we are
* open drain.
*/
WARN_ON(test_bit(FLAG_IS_OUT, &desc->flags) &&
!test_bit(FLAG_OPEN_DRAIN, &desc->flags));
set_bit(FLAG_IRQ_IS_ENABLED, &desc->flags);
}
}
EXPORT_SYMBOL_GPL(gpiochip_enable_irq);
bool gpiochip_line_is_irq(struct gpio_chip *gc, unsigned int offset)
{
if (offset >= gc->ngpio)
return false;
return test_bit(FLAG_USED_AS_IRQ, &gc->gpiodev->descs[offset].flags);
}
EXPORT_SYMBOL_GPL(gpiochip_line_is_irq);
int gpiochip_reqres_irq(struct gpio_chip *gc, unsigned int offset)
{
int ret;
if (!try_module_get(gc->gpiodev->owner))
return -ENODEV;
ret = gpiochip_lock_as_irq(gc, offset);
if (ret) {
chip_err(gc, "unable to lock HW IRQ %u for IRQ\n", offset);
module_put(gc->gpiodev->owner);
return ret;
}
return 0;
}
EXPORT_SYMBOL_GPL(gpiochip_reqres_irq);
void gpiochip_relres_irq(struct gpio_chip *gc, unsigned int offset)
{
gpiochip_unlock_as_irq(gc, offset);
module_put(gc->gpiodev->owner);
}
EXPORT_SYMBOL_GPL(gpiochip_relres_irq);
bool gpiochip_line_is_open_drain(struct gpio_chip *gc, unsigned int offset)
{
if (offset >= gc->ngpio)
return false;
return test_bit(FLAG_OPEN_DRAIN, &gc->gpiodev->descs[offset].flags);
}
EXPORT_SYMBOL_GPL(gpiochip_line_is_open_drain);
bool gpiochip_line_is_open_source(struct gpio_chip *gc, unsigned int offset)
{
if (offset >= gc->ngpio)
return false;
return test_bit(FLAG_OPEN_SOURCE, &gc->gpiodev->descs[offset].flags);
}
EXPORT_SYMBOL_GPL(gpiochip_line_is_open_source);
bool gpiochip_line_is_persistent(struct gpio_chip *gc, unsigned int offset)
{
if (offset >= gc->ngpio)
return false;
return !test_bit(FLAG_TRANSITORY, &gc->gpiodev->descs[offset].flags);
}
EXPORT_SYMBOL_GPL(gpiochip_line_is_persistent);
/**
* gpiod_get_raw_value_cansleep() - return a gpio's raw value
* @desc: gpio whose value will be returned
*
* Return the GPIO's raw value, i.e. the value of the physical line disregarding
* its ACTIVE_LOW status, or negative errno on failure.
*
* This function is to be called from contexts that can sleep.
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
*/
int gpiod_get_raw_value_cansleep(const struct gpio_desc *desc)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
might_sleep_if(extra_checks);
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC(desc);
return gpiod_get_raw_value_commit(desc);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
EXPORT_SYMBOL_GPL(gpiod_get_raw_value_cansleep);
/**
* gpiod_get_value_cansleep() - return a gpio's value
* @desc: gpio whose value will be returned
*
* Return the GPIO's logical value, i.e. taking the ACTIVE_LOW status into
* account, or negative errno on failure.
*
* This function is to be called from contexts that can sleep.
*/
int gpiod_get_value_cansleep(const struct gpio_desc *desc)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
int value;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
might_sleep_if(extra_checks);
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC(desc);
value = gpiod_get_raw_value_commit(desc);
if (value < 0)
return value;
if (test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
return value;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
}
EXPORT_SYMBOL_GPL(gpiod_get_value_cansleep);
/**
* gpiod_get_raw_array_value_cansleep() - read raw values from an array of GPIOs
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @array_size: number of elements in the descriptor array / value bitmap
* @desc_array: array of GPIO descriptors whose values will be read
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
* @array_info: information on applicability of fast bitmap processing path
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @value_bitmap: bitmap to store the read values
*
* Read the raw values of the GPIOs, i.e. the values of the physical lines
* without regard for their ACTIVE_LOW status. Return 0 in case of success,
* else an error code.
*
* This function is to be called from contexts that can sleep.
*/
int gpiod_get_raw_array_value_cansleep(unsigned int array_size,
struct gpio_desc **desc_array,
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
struct gpio_array *array_info,
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
unsigned long *value_bitmap)
{
might_sleep_if(extra_checks);
if (!desc_array)
return -EINVAL;
return gpiod_get_array_value_complex(true, true, array_size,
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
desc_array, array_info,
value_bitmap);
}
EXPORT_SYMBOL_GPL(gpiod_get_raw_array_value_cansleep);
/**
* gpiod_get_array_value_cansleep() - read values from an array of GPIOs
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @array_size: number of elements in the descriptor array / value bitmap
* @desc_array: array of GPIO descriptors whose values will be read
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
* @array_info: information on applicability of fast bitmap processing path
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @value_bitmap: bitmap to store the read values
*
* Read the logical values of the GPIOs, i.e. taking their ACTIVE_LOW status
* into account. Return 0 in case of success, else an error code.
*
* This function is to be called from contexts that can sleep.
*/
int gpiod_get_array_value_cansleep(unsigned int array_size,
struct gpio_desc **desc_array,
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
struct gpio_array *array_info,
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
unsigned long *value_bitmap)
{
might_sleep_if(extra_checks);
if (!desc_array)
return -EINVAL;
return gpiod_get_array_value_complex(false, true, array_size,
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
desc_array, array_info,
value_bitmap);
}
EXPORT_SYMBOL_GPL(gpiod_get_array_value_cansleep);
/**
* gpiod_set_raw_value_cansleep() - assign a gpio's raw value
* @desc: gpio whose value will be assigned
* @value: value to assign
*
* Set the raw value of the GPIO, i.e. the value of its physical line without
* regard for its ACTIVE_LOW status.
*
* This function is to be called from contexts that can sleep.
*/
void gpiod_set_raw_value_cansleep(struct gpio_desc *desc, int value)
{
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
might_sleep_if(extra_checks);
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC_VOID(desc);
gpiod_set_raw_value_commit(desc, value);
}
EXPORT_SYMBOL_GPL(gpiod_set_raw_value_cansleep);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiod_set_value_cansleep() - assign a gpio's value
* @desc: gpio whose value will be assigned
* @value: value to assign
*
* Set the logical value of the GPIO, i.e. taking its ACTIVE_LOW status into
* account
*
* This function is to be called from contexts that can sleep.
*/
void gpiod_set_value_cansleep(struct gpio_desc *desc, int value)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
might_sleep_if(extra_checks);
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
VALIDATE_DESC_VOID(desc);
gpiod_set_value_nocheck(desc, value);
}
EXPORT_SYMBOL_GPL(gpiod_set_value_cansleep);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
/**
* gpiod_set_raw_array_value_cansleep() - assign values to an array of GPIOs
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @array_size: number of elements in the descriptor array / value bitmap
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
* @desc_array: array of GPIO descriptors whose values will be assigned
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
* @array_info: information on applicability of fast bitmap processing path
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @value_bitmap: bitmap of values to assign
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
*
* Set the raw values of the GPIOs, i.e. the values of the physical lines
* without regard for their ACTIVE_LOW status.
*
* This function is to be called from contexts that can sleep.
*/
int gpiod_set_raw_array_value_cansleep(unsigned int array_size,
struct gpio_desc **desc_array,
struct gpio_array *array_info,
unsigned long *value_bitmap)
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
{
might_sleep_if(extra_checks);
if (!desc_array)
return -EINVAL;
return gpiod_set_array_value_complex(true, true, array_size, desc_array,
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
array_info, value_bitmap);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
}
EXPORT_SYMBOL_GPL(gpiod_set_raw_array_value_cansleep);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
/**
* gpiod_add_lookup_tables() - register GPIO device consumers
* @tables: list of tables of consumers to register
* @n: number of tables in the list
*/
void gpiod_add_lookup_tables(struct gpiod_lookup_table **tables, size_t n)
{
unsigned int i;
mutex_lock(&gpio_lookup_lock);
for (i = 0; i < n; i++)
list_add_tail(&tables[i]->list, &gpio_lookup_list);
mutex_unlock(&gpio_lookup_lock);
}
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
/**
* gpiod_set_array_value_cansleep() - assign values to an array of GPIOs
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @array_size: number of elements in the descriptor array / value bitmap
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
* @desc_array: array of GPIO descriptors whose values will be assigned
gpiolib: Pass array info to get/set array functions In order to make use of array info obtained from gpiod_get_array() and speed up processing of arrays matching single GPIO chip layout, that information must be passed to get/set array functions. Extend the functions' API with that additional parameter and update all users. Pass NULL if a user builds an array itself from single GPIOs. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:07 +00:00
* @array_info: information on applicability of fast bitmap processing path
gpiolib: Pass bitmaps, not integer arrays, to get/set array Most users of get/set array functions iterate consecutive bits of data, usually a single integer, while processing array of results obtained from, or building an array of values to be passed to those functions. Save time wasted on those iterations by changing the functions' API to accept bitmaps. All current users are updated as well. More benefits from the change are expected as soon as planned support for accepting/passing those bitmaps directly from/to respective GPIO chip callbacks if applicable is implemented. Cc: Jonathan Corbet <corbet@lwn.net> Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com> Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Cc: Lukas Wunner <lukas@wunner.de> Cc: Peter Korsgaard <peter.korsgaard@barco.com> Cc: Peter Rosin <peda@axentia.se> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Michael Hennerich <Michael.Hennerich@analog.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-09-05 21:50:05 +00:00
* @value_bitmap: bitmap of values to assign
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
*
* Set the logical values of the GPIOs, i.e. taking their ACTIVE_LOW status
* into account.
*
* This function is to be called from contexts that can sleep.
*/
int gpiod_set_array_value_cansleep(unsigned int array_size,
struct gpio_desc **desc_array,
struct gpio_array *array_info,
unsigned long *value_bitmap)
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
{
might_sleep_if(extra_checks);
if (!desc_array)
return -EINVAL;
return gpiod_set_array_value_complex(false, true, array_size,
desc_array, array_info,
value_bitmap);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
}
EXPORT_SYMBOL_GPL(gpiod_set_array_value_cansleep);
gpiolib: allow simultaneous setting of multiple GPIO outputs Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer interface which allow setting multiple outputs with just one function call. Also add an optional set_multiple function to the driver interface. Without an implementation of that function in the chip driver outputs are set sequentially. Implementing the set_multiple function in a chip driver allows for: - Improved performance for certain use cases. The original motivation for this was the task of configuring an FPGA. In that specific case, where 9 GPIO lines have to be set many times, configuration time goes down from 48 s to 20 s when using the new function. - Simultaneous glitch-free setting of multiple pins on any kind of parallel bus attached to GPIOs provided they all reside on the same chip and bank. Limitations: Performance is only improved for normal high-low outputs. Open drain and open source outputs are always set separately from each other. Those kinds of outputs could probably be accelerated in a similar way if we could forgo the error checking when setting GPIO directions. Change log: v6: - rebase on current linux-gpio devel branch v5: - check can_sleep property per chip - remove superfluous checks - supplement documentation v4: - add gpiod_set_array function for setting logical values - change interface of the set_multiple driver function to use unsigned long as type for the bit fields - use generic bitops (which also use unsigned long for bit fields) - do not use ARCH_NR_GPIOS any more v3: - add documentation - change commit message v2: - use descriptor interface - allow arbitrary groups of GPIOs spanning multiple chips Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-11-04 16:12:06 +00:00
/**
* gpiod_add_lookup_table() - register GPIO device consumers
* @table: table of consumers to register
*/
void gpiod_add_lookup_table(struct gpiod_lookup_table *table)
{
mutex_lock(&gpio_lookup_lock);
list_add_tail(&table->list, &gpio_lookup_list);
mutex_unlock(&gpio_lookup_lock);
}
EXPORT_SYMBOL_GPL(gpiod_add_lookup_table);
/**
* gpiod_remove_lookup_table() - unregister GPIO device consumers
* @table: table of consumers to unregister
*/
void gpiod_remove_lookup_table(struct gpiod_lookup_table *table)
{
mutex_lock(&gpio_lookup_lock);
list_del(&table->list);
mutex_unlock(&gpio_lookup_lock);
}
EXPORT_SYMBOL_GPL(gpiod_remove_lookup_table);
/**
* gpiod_add_hogs() - register a set of GPIO hogs from machine code
* @hogs: table of gpio hog entries with a zeroed sentinel at the end
*/
void gpiod_add_hogs(struct gpiod_hog *hogs)
{
struct gpio_chip *gc;
struct gpiod_hog *hog;
mutex_lock(&gpio_machine_hogs_mutex);
for (hog = &hogs[0]; hog->chip_label; hog++) {
list_add_tail(&hog->list, &gpio_machine_hogs);
/*
* The chip may have been registered earlier, so check if it
* exists and, if so, try to hog the line now.
*/
gc = find_chip_by_name(hog->chip_label);
if (gc)
gpiochip_machine_hog(gc, hog);
}
mutex_unlock(&gpio_machine_hogs_mutex);
}
EXPORT_SYMBOL_GPL(gpiod_add_hogs);
static struct gpiod_lookup_table *gpiod_find_lookup_table(struct device *dev)
{
const char *dev_id = dev ? dev_name(dev) : NULL;
struct gpiod_lookup_table *table;
mutex_lock(&gpio_lookup_lock);
list_for_each_entry(table, &gpio_lookup_list, list) {
if (table->dev_id && dev_id) {
/*
* Valid strings on both ends, must be identical to have
* a match
*/
if (!strcmp(table->dev_id, dev_id))
goto found;
} else {
/*
* One of the pointers is NULL, so both must be to have
* a match
*/
if (dev_id == table->dev_id)
goto found;
}
}
table = NULL;
found:
mutex_unlock(&gpio_lookup_lock);
return table;
}
static struct gpio_desc *gpiod_find(struct device *dev, const char *con_id,
unsigned int idx, unsigned long *flags)
{
struct gpio_desc *desc = ERR_PTR(-ENOENT);
struct gpiod_lookup_table *table;
struct gpiod_lookup *p;
table = gpiod_find_lookup_table(dev);
if (!table)
return desc;
for (p = &table->table[0]; p->key; p++) {
struct gpio_chip *gc;
/* idx must always match exactly */
if (p->idx != idx)
continue;
/* If the lookup entry has a con_id, require exact match */
if (p->con_id && (!con_id || strcmp(p->con_id, con_id)))
continue;
if (p->chip_hwnum == U16_MAX) {
desc = gpio_name_to_desc(p->key);
if (desc) {
*flags = p->flags;
return desc;
}
dev_warn(dev, "cannot find GPIO line %s, deferring\n",
p->key);
return ERR_PTR(-EPROBE_DEFER);
}
gc = find_chip_by_name(p->key);
if (!gc) {
/*
* As the lookup table indicates a chip with
* p->key should exist, assume it may
* still appear later and let the interested
* consumer be probed again or let the Deferred
* Probe infrastructure handle the error.
*/
dev_warn(dev, "cannot find GPIO chip %s, deferring\n",
p->key);
return ERR_PTR(-EPROBE_DEFER);
}
if (gc->ngpio <= p->chip_hwnum) {
dev_err(dev,
"requested GPIO %u (%u) is out of range [0..%u] for chip %s\n",
idx, p->chip_hwnum, gc->ngpio - 1,
gc->label);
return ERR_PTR(-EINVAL);
}
desc = gpiochip_get_desc(gc, p->chip_hwnum);
*flags = p->flags;
return desc;
}
return desc;
}
static int platform_gpio_count(struct device *dev, const char *con_id)
{
struct gpiod_lookup_table *table;
struct gpiod_lookup *p;
unsigned int count = 0;
table = gpiod_find_lookup_table(dev);
if (!table)
return -ENOENT;
for (p = &table->table[0]; p->key; p++) {
if ((con_id && p->con_id && !strcmp(con_id, p->con_id)) ||
(!con_id && !p->con_id))
count++;
}
if (!count)
return -ENOENT;
return count;
}
/**
* fwnode_gpiod_get_index - obtain a GPIO from firmware node
* @fwnode: handle of the firmware node
* @con_id: function within the GPIO consumer
* @index: index of the GPIO to obtain for the consumer
* @flags: GPIO initialization flags
* @label: label to attach to the requested GPIO
*
* This function can be used for drivers that get their configuration
* from opaque firmware.
*
* The function properly finds the corresponding GPIO using whatever is the
* underlying firmware interface and then makes sure that the GPIO
* descriptor is requested before it is returned to the caller.
*
* Returns:
* On successful request the GPIO pin is configured in accordance with
* provided @flags.
*
* In case of error an ERR_PTR() is returned.
*/
struct gpio_desc *fwnode_gpiod_get_index(struct fwnode_handle *fwnode,
const char *con_id, int index,
enum gpiod_flags flags,
const char *label)
{
struct gpio_desc *desc;
char prop_name[32]; /* 32 is max size of property name */
unsigned int i;
for (i = 0; i < ARRAY_SIZE(gpio_suffixes); i++) {
if (con_id)
snprintf(prop_name, sizeof(prop_name), "%s-%s",
con_id, gpio_suffixes[i]);
else
snprintf(prop_name, sizeof(prop_name), "%s",
gpio_suffixes[i]);
desc = fwnode_get_named_gpiod(fwnode, prop_name, index, flags,
label);
if (!IS_ERR(desc) || (PTR_ERR(desc) != -ENOENT))
break;
}
return desc;
}
EXPORT_SYMBOL_GPL(fwnode_gpiod_get_index);
/**
* gpiod_count - return the number of GPIOs associated with a device / function
* or -ENOENT if no GPIO has been assigned to the requested function
* @dev: GPIO consumer, can be NULL for system-global GPIOs
* @con_id: function within the GPIO consumer
*/
int gpiod_count(struct device *dev, const char *con_id)
{
int count = -ENOENT;
if (IS_ENABLED(CONFIG_OF) && dev && dev->of_node)
count = of_gpio_get_count(dev, con_id);
else if (IS_ENABLED(CONFIG_ACPI) && dev && ACPI_HANDLE(dev))
count = acpi_gpio_count(dev, con_id);
if (count < 0)
count = platform_gpio_count(dev, con_id);
return count;
}
EXPORT_SYMBOL_GPL(gpiod_count);
/**
* gpiod_get - obtain a GPIO for a given GPIO function
* @dev: GPIO consumer, can be NULL for system-global GPIOs
* @con_id: function within the GPIO consumer
* @flags: optional GPIO initialization flags
*
* Return the GPIO descriptor corresponding to the function con_id of device
* dev, -ENOENT if no GPIO has been assigned to the requested function, or
* another IS_ERR() code if an error occurred while trying to acquire the GPIO.
*/
struct gpio_desc *__must_check gpiod_get(struct device *dev, const char *con_id,
enum gpiod_flags flags)
{
return gpiod_get_index(dev, con_id, 0, flags);
}
EXPORT_SYMBOL_GPL(gpiod_get);
/**
* gpiod_get_optional - obtain an optional GPIO for a given GPIO function
* @dev: GPIO consumer, can be NULL for system-global GPIOs
* @con_id: function within the GPIO consumer
* @flags: optional GPIO initialization flags
*
* This is equivalent to gpiod_get(), except that when no GPIO was assigned to
* the requested function it will return NULL. This is convenient for drivers
* that need to handle optional GPIOs.
*/
struct gpio_desc *__must_check gpiod_get_optional(struct device *dev,
const char *con_id,
enum gpiod_flags flags)
{
return gpiod_get_index_optional(dev, con_id, 0, flags);
}
EXPORT_SYMBOL_GPL(gpiod_get_optional);
/**
* gpiod_configure_flags - helper function to configure a given GPIO
* @desc: gpio whose value will be assigned
* @con_id: function within the GPIO consumer
* @lflags: bitmask of gpio_lookup_flags GPIO_* values - returned from
* of_find_gpio() or of_get_gpio_hog()
* @dflags: gpiod_flags - optional GPIO initialization flags
*
* Return 0 on success, -ENOENT if no GPIO has been assigned to the
* requested function and/or index, or another IS_ERR() code if an error
* occurred while trying to acquire the GPIO.
*/
int gpiod_configure_flags(struct gpio_desc *desc, const char *con_id,
unsigned long lflags, enum gpiod_flags dflags)
{
int ret;
if (lflags & GPIO_ACTIVE_LOW)
set_bit(FLAG_ACTIVE_LOW, &desc->flags);
if (lflags & GPIO_OPEN_DRAIN)
set_bit(FLAG_OPEN_DRAIN, &desc->flags);
else if (dflags & GPIOD_FLAGS_BIT_OPEN_DRAIN) {
/*
* This enforces open drain mode from the consumer side.
* This is necessary for some busses like I2C, but the lookup
* should *REALLY* have specified them as open drain in the
* first place, so print a little warning here.
*/
set_bit(FLAG_OPEN_DRAIN, &desc->flags);
gpiod_warn(desc,
"enforced open drain please flag it properly in DT/ACPI DSDT/board file\n");
}
if (lflags & GPIO_OPEN_SOURCE)
set_bit(FLAG_OPEN_SOURCE, &desc->flags);
if ((lflags & GPIO_PULL_UP) && (lflags & GPIO_PULL_DOWN)) {
gpiod_err(desc,
"both pull-up and pull-down enabled, invalid configuration\n");
return -EINVAL;
}
if (lflags & GPIO_PULL_UP)
set_bit(FLAG_PULL_UP, &desc->flags);
else if (lflags & GPIO_PULL_DOWN)
set_bit(FLAG_PULL_DOWN, &desc->flags);
ret = gpiod_set_transitory(desc, (lflags & GPIO_TRANSITORY));
if (ret < 0)
return ret;
/* No particular flag request, return here... */
if (!(dflags & GPIOD_FLAGS_BIT_DIR_SET)) {
gpiod_dbg(desc, "no flags found for %s\n", con_id);
return 0;
}
/* Process flags */
if (dflags & GPIOD_FLAGS_BIT_DIR_OUT)
ret = gpiod_direction_output(desc,
!!(dflags & GPIOD_FLAGS_BIT_DIR_VAL));
else
ret = gpiod_direction_input(desc);
return ret;
}
/**
* gpiod_get_index - obtain a GPIO from a multi-index GPIO function
* @dev: GPIO consumer, can be NULL for system-global GPIOs
* @con_id: function within the GPIO consumer
* @idx: index of the GPIO to obtain in the consumer
* @flags: optional GPIO initialization flags
*
* This variant of gpiod_get() allows to access GPIOs other than the first
* defined one for functions that define several GPIOs.
*
* Return a valid GPIO descriptor, -ENOENT if no GPIO has been assigned to the
* requested function and/or index, or another IS_ERR() code if an error
* occurred while trying to acquire the GPIO.
*/
struct gpio_desc *__must_check gpiod_get_index(struct device *dev,
const char *con_id,
unsigned int idx,
enum gpiod_flags flags)
{
unsigned long lookupflags = GPIO_LOOKUP_FLAGS_DEFAULT;
struct gpio_desc *desc = NULL;
int ret;
/* Maybe we have a device name, maybe not */
const char *devname = dev ? dev_name(dev) : "?";
dev_dbg(dev, "GPIO lookup for consumer %s\n", con_id);
if (dev) {
/* Using device tree? */
if (IS_ENABLED(CONFIG_OF) && dev->of_node) {
dev_dbg(dev, "using device tree for GPIO lookup\n");
desc = of_find_gpio(dev, con_id, idx, &lookupflags);
} else if (ACPI_COMPANION(dev)) {
dev_dbg(dev, "using ACPI for GPIO lookup\n");
desc = acpi_find_gpio(dev, con_id, idx, &flags, &lookupflags);
}
}
/*
* Either we are not using DT or ACPI, or their lookup did not return
* a result. In that case, use platform lookup as a fallback.
*/
if (!desc || desc == ERR_PTR(-ENOENT)) {
dev_dbg(dev, "using lookup tables for GPIO lookup\n");
desc = gpiod_find(dev, con_id, idx, &lookupflags);
}
if (IS_ERR(desc)) {
dev_dbg(dev, "No GPIO consumer %s found\n", con_id);
return desc;
}
/*
* If a connection label was passed use that, else attempt to use
* the device name as label
*/
ret = gpiod_request(desc, con_id ? con_id : devname);
if (ret < 0) {
if (ret == -EBUSY && flags & GPIOD_FLAGS_BIT_NONEXCLUSIVE) {
/*
* This happens when there are several consumers for
* the same GPIO line: we just return here without
* further initialization. It is a bit if a hack.
* This is necessary to support fixed regulators.
*
* FIXME: Make this more sane and safe.
*/
dev_info(dev, "nonexclusive access to GPIO for %s\n",
con_id ? con_id : devname);
return desc;
} else {
return ERR_PTR(ret);
}
}
ret = gpiod_configure_flags(desc, con_id, lookupflags, flags);
if (ret < 0) {
dev_dbg(dev, "setup of GPIO %s failed\n", con_id);
gpiod_put(desc);
return ERR_PTR(ret);
}
blocking_notifier_call_chain(&desc->gdev->notifier,
GPIOLINE_CHANGED_REQUESTED, desc);
return desc;
}
EXPORT_SYMBOL_GPL(gpiod_get_index);
/**
* fwnode_get_named_gpiod - obtain a GPIO from firmware node
* @fwnode: handle of the firmware node
* @propname: name of the firmware property representing the GPIO
* @index: index of the GPIO to obtain for the consumer
* @dflags: GPIO initialization flags
* @label: label to attach to the requested GPIO
*
* This function can be used for drivers that get their configuration
* from opaque firmware.
*
* The function properly finds the corresponding GPIO using whatever is the
* underlying firmware interface and then makes sure that the GPIO
* descriptor is requested before it is returned to the caller.
*
* Returns:
* On successful request the GPIO pin is configured in accordance with
* provided @dflags.
*
* In case of error an ERR_PTR() is returned.
*/
struct gpio_desc *fwnode_get_named_gpiod(struct fwnode_handle *fwnode,
const char *propname, int index,
enum gpiod_flags dflags,
const char *label)
{
unsigned long lflags = GPIO_LOOKUP_FLAGS_DEFAULT;
struct gpio_desc *desc = ERR_PTR(-ENODEV);
int ret;
if (!fwnode)
return ERR_PTR(-EINVAL);
if (is_of_node(fwnode)) {
desc = gpiod_get_from_of_node(to_of_node(fwnode),
propname, index,
dflags,
label);
return desc;
} else if (is_acpi_node(fwnode)) {
struct acpi_gpio_info info;
desc = acpi_node_get_gpiod(fwnode, propname, index, &info);
if (IS_ERR(desc))
return desc;
acpi_gpio_update_gpiod_flags(&dflags, &info);
acpi_gpio_update_gpiod_lookup_flags(&lflags, &info);
}
/* Currently only ACPI takes this path */
ret = gpiod_request(desc, label);
if (ret)
return ERR_PTR(ret);
ret = gpiod_configure_flags(desc, propname, lflags, dflags);
if (ret < 0) {
gpiod_put(desc);
return ERR_PTR(ret);
}
blocking_notifier_call_chain(&desc->gdev->notifier,
GPIOLINE_CHANGED_REQUESTED, desc);
return desc;
}
EXPORT_SYMBOL_GPL(fwnode_get_named_gpiod);
/**
* gpiod_get_index_optional - obtain an optional GPIO from a multi-index GPIO
* function
* @dev: GPIO consumer, can be NULL for system-global GPIOs
* @con_id: function within the GPIO consumer
* @index: index of the GPIO to obtain in the consumer
* @flags: optional GPIO initialization flags
*
* This is equivalent to gpiod_get_index(), except that when no GPIO with the
* specified index was assigned to the requested function it will return NULL.
* This is convenient for drivers that need to handle optional GPIOs.
*/
struct gpio_desc *__must_check gpiod_get_index_optional(struct device *dev,
const char *con_id,
unsigned int index,
enum gpiod_flags flags)
{
struct gpio_desc *desc;
desc = gpiod_get_index(dev, con_id, index, flags);
if (IS_ERR(desc)) {
if (PTR_ERR(desc) == -ENOENT)
return NULL;
}
return desc;
}
EXPORT_SYMBOL_GPL(gpiod_get_index_optional);
/**
* gpiod_hog - Hog the specified GPIO desc given the provided flags
* @desc: gpio whose value will be assigned
* @name: gpio line name
* @lflags: bitmask of gpio_lookup_flags GPIO_* values - returned from
* of_find_gpio() or of_get_gpio_hog()
* @dflags: gpiod_flags - optional GPIO initialization flags
*/
int gpiod_hog(struct gpio_desc *desc, const char *name,
unsigned long lflags, enum gpiod_flags dflags)
{
struct gpio_chip *gc;
struct gpio_desc *local_desc;
int hwnum;
int ret;
gc = gpiod_to_chip(desc);
hwnum = gpio_chip_hwgpio(desc);
local_desc = gpiochip_request_own_desc(gc, hwnum, name,
lflags, dflags);
if (IS_ERR(local_desc)) {
ret = PTR_ERR(local_desc);
pr_err("requesting hog GPIO %s (chip %s, offset %d) failed, %d\n",
name, gc->label, hwnum, ret);
return ret;
}
/* Mark GPIO as hogged so it can be identified and removed later */
set_bit(FLAG_IS_HOGGED, &desc->flags);
gpiod_info(desc, "hogged as %s%s\n",
(dflags & GPIOD_FLAGS_BIT_DIR_OUT) ? "output" : "input",
(dflags & GPIOD_FLAGS_BIT_DIR_OUT) ?
(dflags & GPIOD_FLAGS_BIT_DIR_VAL) ? "/high" : "/low" : "");
return 0;
}
/**
* gpiochip_free_hogs - Scan gpio-controller chip and release GPIO hog
* @gc: gpio chip to act on
*/
static void gpiochip_free_hogs(struct gpio_chip *gc)
{
int id;
for (id = 0; id < gc->ngpio; id++) {
if (test_bit(FLAG_IS_HOGGED, &gc->gpiodev->descs[id].flags))
gpiochip_free_own_desc(&gc->gpiodev->descs[id]);
}
}
/**
* gpiod_get_array - obtain multiple GPIOs from a multi-index GPIO function
* @dev: GPIO consumer, can be NULL for system-global GPIOs
* @con_id: function within the GPIO consumer
* @flags: optional GPIO initialization flags
*
* This function acquires all the GPIOs defined under a given function.
*
* Return a struct gpio_descs containing an array of descriptors, -ENOENT if
* no GPIO has been assigned to the requested function, or another IS_ERR()
* code if an error occurred while trying to acquire the GPIOs.
*/
struct gpio_descs *__must_check gpiod_get_array(struct device *dev,
const char *con_id,
enum gpiod_flags flags)
{
struct gpio_desc *desc;
struct gpio_descs *descs;
struct gpio_array *array_info = NULL;
struct gpio_chip *gc;
int count, bitmap_size;
count = gpiod_count(dev, con_id);
if (count < 0)
return ERR_PTR(count);
treewide: Use struct_size() for kmalloc()-family One of the more common cases of allocation size calculations is finding the size of a structure that has a zero-sized array at the end, along with memory for some number of elements for that array. For example: struct foo { int stuff; void *entry[]; }; instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL); Instead of leaving these open-coded and prone to type mistakes, we can now use the new struct_size() helper: instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL); This patch makes the changes for kmalloc()-family (and kvmalloc()-family) uses. It was done via automatic conversion with manual review for the "CHECKME" non-standard cases noted below, using the following Coccinelle script: // pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len * // sizeof *pkey_cache->table, GFP_KERNEL); @@ identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc"; expression GFP; identifier VAR, ELEMENT; expression COUNT; @@ - alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP) + alloc(struct_size(VAR, ELEMENT, COUNT), GFP) // mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL); @@ identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc"; expression GFP; identifier VAR, ELEMENT; expression COUNT; @@ - alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP) + alloc(struct_size(VAR, ELEMENT, COUNT), GFP) // Same pattern, but can't trivially locate the trailing element name, // or variable name. @@ identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc"; expression GFP; expression SOMETHING, COUNT, ELEMENT; @@ - alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP) + alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-05-08 20:45:50 +00:00
descs = kzalloc(struct_size(descs, desc, count), GFP_KERNEL);
if (!descs)
return ERR_PTR(-ENOMEM);
for (descs->ndescs = 0; descs->ndescs < count; ) {
desc = gpiod_get_index(dev, con_id, descs->ndescs, flags);
if (IS_ERR(desc)) {
gpiod_put_array(descs);
return ERR_CAST(desc);
}
descs->desc[descs->ndescs] = desc;
gc = gpiod_to_chip(desc);
/*
2018-09-23 23:53:36 +00:00
* If pin hardware number of array member 0 is also 0, select
* its chip as a candidate for fast bitmap processing path.
*/
2018-09-23 23:53:36 +00:00
if (descs->ndescs == 0 && gpio_chip_hwgpio(desc) == 0) {
struct gpio_descs *array;
bitmap_size = BITS_TO_LONGS(gc->ngpio > count ?
gc->ngpio : count);
array = kzalloc(struct_size(descs, desc, count) +
struct_size(array_info, invert_mask,
3 * bitmap_size), GFP_KERNEL);
if (!array) {
gpiod_put_array(descs);
return ERR_PTR(-ENOMEM);
}
memcpy(array, descs,
struct_size(descs, desc, descs->ndescs + 1));
kfree(descs);
descs = array;
array_info = (void *)(descs->desc + count);
array_info->get_mask = array_info->invert_mask +
bitmap_size;
array_info->set_mask = array_info->get_mask +
bitmap_size;
array_info->desc = descs->desc;
array_info->size = count;
array_info->chip = gc;
bitmap_set(array_info->get_mask, descs->ndescs,
count - descs->ndescs);
bitmap_set(array_info->set_mask, descs->ndescs,
count - descs->ndescs);
descs->info = array_info;
}
2018-09-23 23:53:36 +00:00
/* Unmark array members which don't belong to the 'fast' chip */
if (array_info && array_info->chip != gc) {
__clear_bit(descs->ndescs, array_info->get_mask);
__clear_bit(descs->ndescs, array_info->set_mask);
2018-09-23 23:53:36 +00:00
}
/*
* Detect array members which belong to the 'fast' chip
* but their pins are not in hardware order.
*/
else if (array_info &&
gpio_chip_hwgpio(desc) != descs->ndescs) {
/*
* Don't use fast path if all array members processed so
* far belong to the same chip as this one but its pin
* hardware number is different from its array index.
*/
if (bitmap_full(array_info->get_mask, descs->ndescs)) {
array_info = NULL;
} else {
__clear_bit(descs->ndescs,
array_info->get_mask);
__clear_bit(descs->ndescs,
array_info->set_mask);
}
} else if (array_info) {
/* Exclude open drain or open source from fast output */
if (gpiochip_line_is_open_drain(gc, descs->ndescs) ||
gpiochip_line_is_open_source(gc, descs->ndescs))
__clear_bit(descs->ndescs,
array_info->set_mask);
/* Identify 'fast' pins which require invertion */
if (gpiod_is_active_low(desc))
__set_bit(descs->ndescs,
array_info->invert_mask);
}
descs->ndescs++;
}
if (array_info)
dev_dbg(dev,
"GPIO array info: chip=%s, size=%d, get_mask=%lx, set_mask=%lx, invert_mask=%lx\n",
array_info->chip->label, array_info->size,
*array_info->get_mask, *array_info->set_mask,
*array_info->invert_mask);
return descs;
}
EXPORT_SYMBOL_GPL(gpiod_get_array);
/**
* gpiod_get_array_optional - obtain multiple GPIOs from a multi-index GPIO
* function
* @dev: GPIO consumer, can be NULL for system-global GPIOs
* @con_id: function within the GPIO consumer
* @flags: optional GPIO initialization flags
*
* This is equivalent to gpiod_get_array(), except that when no GPIO was
* assigned to the requested function it will return NULL.
*/
struct gpio_descs *__must_check gpiod_get_array_optional(struct device *dev,
const char *con_id,
enum gpiod_flags flags)
{
struct gpio_descs *descs;
descs = gpiod_get_array(dev, con_id, flags);
if (PTR_ERR(descs) == -ENOENT)
return NULL;
return descs;
}
EXPORT_SYMBOL_GPL(gpiod_get_array_optional);
/**
* gpiod_put - dispose of a GPIO descriptor
* @desc: GPIO descriptor to dispose of
*
* No descriptor can be used after gpiod_put() has been called on it.
*/
void gpiod_put(struct gpio_desc *desc)
{
if (desc)
gpiod_free(desc);
}
EXPORT_SYMBOL_GPL(gpiod_put);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
/**
* gpiod_put_array - dispose of multiple GPIO descriptors
* @descs: struct gpio_descs containing an array of descriptors
*/
void gpiod_put_array(struct gpio_descs *descs)
{
unsigned int i;
for (i = 0; i < descs->ndescs; i++)
gpiod_put(descs->desc[i]);
kfree(descs);
}
EXPORT_SYMBOL_GPL(gpiod_put_array);
gpio: add a userspace chardev ABI for GPIOs A new chardev that is to be used for userspace GPIO access is added in this patch. It is intended to gradually replace the horribly broken sysfs ABI. Using a chardev has many upsides: - All operations are per-gpiochip, which is the actual device underlying the GPIOs, making us tie in to the kernel device model properly. - Hotpluggable GPIO controllers can come and go, as this kind of problem has been know to userspace for character devices since ages, and if a gpiochip handle is held in userspace we know we will break something, whereas the sysfs is stateless. - The one-value-per-file rule of sysfs is really hard to maintain when you want to twist more than one knob at a time, for example have in-kernel APIs to switch several GPIO lines at the same time, and this will be possible to do with a single ioctl() from userspace, saving a lot of context switching. We also need to add a new bus type for GPIO. This is necessary for example for userspace coldplug, where sysfs is traversed to find the boot-time device nodes and create the character devices in /dev. This new chardev ABI is *non* *optional* and can be counted on to be present in the future, emphasizing the preference of this ABI. The ABI only implements one single ioctl() to get the name and number of GPIO lines of a chip. Even this is debatable: see it as a minimal example for review. This ABI shall be ruthlessly reviewed and etched in stone. The old /sys/class/gpio is still optional to compile in, but will be deprecated. Unique device IDs are created using IDR, which is overkill and insanely scalable, but also well tested. Cc: Johan Hovold <johan@kernel.org> Cc: Michael Welling <mwelling@ieee.org> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 13:29:53 +00:00
static int __init gpiolib_dev_init(void)
{
int ret;
/* Register GPIO sysfs bus */
ret = bus_register(&gpio_bus_type);
gpio: add a userspace chardev ABI for GPIOs A new chardev that is to be used for userspace GPIO access is added in this patch. It is intended to gradually replace the horribly broken sysfs ABI. Using a chardev has many upsides: - All operations are per-gpiochip, which is the actual device underlying the GPIOs, making us tie in to the kernel device model properly. - Hotpluggable GPIO controllers can come and go, as this kind of problem has been know to userspace for character devices since ages, and if a gpiochip handle is held in userspace we know we will break something, whereas the sysfs is stateless. - The one-value-per-file rule of sysfs is really hard to maintain when you want to twist more than one knob at a time, for example have in-kernel APIs to switch several GPIO lines at the same time, and this will be possible to do with a single ioctl() from userspace, saving a lot of context switching. We also need to add a new bus type for GPIO. This is necessary for example for userspace coldplug, where sysfs is traversed to find the boot-time device nodes and create the character devices in /dev. This new chardev ABI is *non* *optional* and can be counted on to be present in the future, emphasizing the preference of this ABI. The ABI only implements one single ioctl() to get the name and number of GPIO lines of a chip. Even this is debatable: see it as a minimal example for review. This ABI shall be ruthlessly reviewed and etched in stone. The old /sys/class/gpio is still optional to compile in, but will be deprecated. Unique device IDs are created using IDR, which is overkill and insanely scalable, but also well tested. Cc: Johan Hovold <johan@kernel.org> Cc: Michael Welling <mwelling@ieee.org> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 13:29:53 +00:00
if (ret < 0) {
pr_err("gpiolib: could not register GPIO bus type\n");
return ret;
}
ret = alloc_chrdev_region(&gpio_devt, 0, GPIO_DEV_MAX, GPIOCHIP_NAME);
gpio: add a userspace chardev ABI for GPIOs A new chardev that is to be used for userspace GPIO access is added in this patch. It is intended to gradually replace the horribly broken sysfs ABI. Using a chardev has many upsides: - All operations are per-gpiochip, which is the actual device underlying the GPIOs, making us tie in to the kernel device model properly. - Hotpluggable GPIO controllers can come and go, as this kind of problem has been know to userspace for character devices since ages, and if a gpiochip handle is held in userspace we know we will break something, whereas the sysfs is stateless. - The one-value-per-file rule of sysfs is really hard to maintain when you want to twist more than one knob at a time, for example have in-kernel APIs to switch several GPIO lines at the same time, and this will be possible to do with a single ioctl() from userspace, saving a lot of context switching. We also need to add a new bus type for GPIO. This is necessary for example for userspace coldplug, where sysfs is traversed to find the boot-time device nodes and create the character devices in /dev. This new chardev ABI is *non* *optional* and can be counted on to be present in the future, emphasizing the preference of this ABI. The ABI only implements one single ioctl() to get the name and number of GPIO lines of a chip. Even this is debatable: see it as a minimal example for review. This ABI shall be ruthlessly reviewed and etched in stone. The old /sys/class/gpio is still optional to compile in, but will be deprecated. Unique device IDs are created using IDR, which is overkill and insanely scalable, but also well tested. Cc: Johan Hovold <johan@kernel.org> Cc: Michael Welling <mwelling@ieee.org> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 13:29:53 +00:00
if (ret < 0) {
pr_err("gpiolib: failed to allocate char dev region\n");
bus_unregister(&gpio_bus_type);
return ret;
gpio: add a userspace chardev ABI for GPIOs A new chardev that is to be used for userspace GPIO access is added in this patch. It is intended to gradually replace the horribly broken sysfs ABI. Using a chardev has many upsides: - All operations are per-gpiochip, which is the actual device underlying the GPIOs, making us tie in to the kernel device model properly. - Hotpluggable GPIO controllers can come and go, as this kind of problem has been know to userspace for character devices since ages, and if a gpiochip handle is held in userspace we know we will break something, whereas the sysfs is stateless. - The one-value-per-file rule of sysfs is really hard to maintain when you want to twist more than one knob at a time, for example have in-kernel APIs to switch several GPIO lines at the same time, and this will be possible to do with a single ioctl() from userspace, saving a lot of context switching. We also need to add a new bus type for GPIO. This is necessary for example for userspace coldplug, where sysfs is traversed to find the boot-time device nodes and create the character devices in /dev. This new chardev ABI is *non* *optional* and can be counted on to be present in the future, emphasizing the preference of this ABI. The ABI only implements one single ioctl() to get the name and number of GPIO lines of a chip. Even this is debatable: see it as a minimal example for review. This ABI shall be ruthlessly reviewed and etched in stone. The old /sys/class/gpio is still optional to compile in, but will be deprecated. Unique device IDs are created using IDR, which is overkill and insanely scalable, but also well tested. Cc: Johan Hovold <johan@kernel.org> Cc: Michael Welling <mwelling@ieee.org> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 13:29:53 +00:00
}
gpiolib_initialized = true;
gpiochip_setup_devs();
#if IS_ENABLED(CONFIG_OF_DYNAMIC) && IS_ENABLED(CONFIG_OF_GPIO)
WARN_ON(of_reconfig_notifier_register(&gpio_of_notifier));
#endif /* CONFIG_OF_DYNAMIC && CONFIG_OF_GPIO */
gpio: add a userspace chardev ABI for GPIOs A new chardev that is to be used for userspace GPIO access is added in this patch. It is intended to gradually replace the horribly broken sysfs ABI. Using a chardev has many upsides: - All operations are per-gpiochip, which is the actual device underlying the GPIOs, making us tie in to the kernel device model properly. - Hotpluggable GPIO controllers can come and go, as this kind of problem has been know to userspace for character devices since ages, and if a gpiochip handle is held in userspace we know we will break something, whereas the sysfs is stateless. - The one-value-per-file rule of sysfs is really hard to maintain when you want to twist more than one knob at a time, for example have in-kernel APIs to switch several GPIO lines at the same time, and this will be possible to do with a single ioctl() from userspace, saving a lot of context switching. We also need to add a new bus type for GPIO. This is necessary for example for userspace coldplug, where sysfs is traversed to find the boot-time device nodes and create the character devices in /dev. This new chardev ABI is *non* *optional* and can be counted on to be present in the future, emphasizing the preference of this ABI. The ABI only implements one single ioctl() to get the name and number of GPIO lines of a chip. Even this is debatable: see it as a minimal example for review. This ABI shall be ruthlessly reviewed and etched in stone. The old /sys/class/gpio is still optional to compile in, but will be deprecated. Unique device IDs are created using IDR, which is overkill and insanely scalable, but also well tested. Cc: Johan Hovold <johan@kernel.org> Cc: Michael Welling <mwelling@ieee.org> Cc: Markus Pargmann <mpa@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-10-21 13:29:53 +00:00
return ret;
}
core_initcall(gpiolib_dev_init);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
#ifdef CONFIG_DEBUG_FS
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
static void gpiolib_dbg_show(struct seq_file *s, struct gpio_device *gdev)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
unsigned i;
struct gpio_chip *gc = gdev->chip;
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
unsigned gpio = gdev->base;
struct gpio_desc *gdesc = &gdev->descs[0];
bool is_out;
bool is_irq;
bool active_low;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
for (i = 0; i < gdev->ngpio; i++, gpio++, gdesc++) {
if (!test_bit(FLAG_REQUESTED, &gdesc->flags)) {
if (gdesc->name) {
seq_printf(s, " gpio-%-3d (%-20.20s)\n",
gpio, gdesc->name);
}
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
continue;
}
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
gpiod_get_direction(gdesc);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
is_out = test_bit(FLAG_IS_OUT, &gdesc->flags);
is_irq = test_bit(FLAG_USED_AS_IRQ, &gdesc->flags);
active_low = test_bit(FLAG_ACTIVE_LOW, &gdesc->flags);
seq_printf(s, " gpio-%-3d (%-20.20s|%-20.20s) %s %s %s%s",
gpio, gdesc->name ? gdesc->name : "", gdesc->label,
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
is_out ? "out" : "in ",
gc->get ? (gc->get(gc, i) ? "hi" : "lo") : "? ",
is_irq ? "IRQ " : "",
active_low ? "ACTIVE LOW" : "");
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
seq_printf(s, "\n");
}
}
static void *gpiolib_seq_start(struct seq_file *s, loff_t *pos)
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
{
unsigned long flags;
struct gpio_device *gdev = NULL;
loff_t index = *pos;
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
s->private = "";
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
spin_lock_irqsave(&gpio_lock, flags);
list_for_each_entry(gdev, &gpio_devices, list)
if (index-- == 0) {
spin_unlock_irqrestore(&gpio_lock, flags);
return gdev;
}
spin_unlock_irqrestore(&gpio_lock, flags);
return NULL;
}
static void *gpiolib_seq_next(struct seq_file *s, void *v, loff_t *pos)
{
unsigned long flags;
struct gpio_device *gdev = v;
void *ret = NULL;
spin_lock_irqsave(&gpio_lock, flags);
if (list_is_last(&gdev->list, &gpio_devices))
ret = NULL;
else
ret = list_entry(gdev->list.next, struct gpio_device, list);
spin_unlock_irqrestore(&gpio_lock, flags);
s->private = "\n";
++*pos;
return ret;
}
static void gpiolib_seq_stop(struct seq_file *s, void *v)
{
}
static int gpiolib_seq_show(struct seq_file *s, void *v)
{
struct gpio_device *gdev = v;
struct gpio_chip *gc = gdev->chip;
struct device *parent;
if (!gc) {
seq_printf(s, "%s%s: (dangling chip)", (char *)s->private,
dev_name(&gdev->dev));
return 0;
}
seq_printf(s, "%s%s: GPIOs %d-%d", (char *)s->private,
dev_name(&gdev->dev),
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
gdev->base, gdev->base + gdev->ngpio - 1);
parent = gc->parent;
if (parent)
seq_printf(s, ", parent: %s/%s",
parent->bus ? parent->bus->name : "no-bus",
dev_name(parent));
if (gc->label)
seq_printf(s, ", %s", gc->label);
if (gc->can_sleep)
seq_printf(s, ", can sleep");
seq_printf(s, ":\n");
if (gc->dbg_show)
gc->dbg_show(s, gc);
else
gpio: reflect base and ngpio into gpio_device Some information about the GPIO chip need to stay around also after the gpio_chip has been removed and only the gpio_device persist. The base and ngpio are such things, for example we don't want a new chip arriving to overlap the number space of a dangling gpio_device, and the chardev may still query the device for the number of lines etc. Note that the code that assigns base and insert gpio_device into the global list no longer check for a missing gpio_chip: we respect the number space allocated by any other gpio_device. As a consequence of the gdev being referenced directly from the gpio_desc, we need to verify it differently from all in-kernel API calls that fall through to direct queries to the gpio_chip vtable: we first check that desc is !NULL, then that desc->gdev is !NULL, then, if desc->gdev->chip is NULL, we *BAIL OUT* without any error, so as to manage the case where operations are requested on a device that is gone. These checks were non-uniform and partly missing in the past: so to simplify: create the macros VALIDATE_DESC() that will return -EINVAL if the desc or desc->gdev is missing and just 0 if the chip is gone, and conversely VALIDATE_DESC_VOID() for the case where the function does not return an error. By using these macros, we get warning messages about missing gdev with reference to the right function in the kernel log. Despite the macro business this simplifies the code and make it more readable than if we copy/paste the same descriptor checking code into all code ABI call sites (IMHO). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-02-10 09:57:36 +00:00
gpiolib_dbg_show(s, gdev);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
return 0;
}
static const struct seq_operations gpiolib_sops = {
.start = gpiolib_seq_start,
.next = gpiolib_seq_next,
.stop = gpiolib_seq_stop,
.show = gpiolib_seq_show,
};
DEFINE_SEQ_ATTRIBUTE(gpiolib);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
static int __init gpiolib_debugfs_init(void)
{
/* /sys/kernel/debug/gpio */
debugfs_create_file("gpio", 0444, NULL, NULL, &gpiolib_fops);
gpiolib: add gpio provider infrastructure Provide new implementation infrastructure that platforms may choose to use when implementing the GPIO programming interface. Platforms can update their GPIO support to use this. In many cases the incremental cost to access a non-inlined GPIO should be less than a dozen instructions, with the memory cost being about a page (total) of extra data and code. The upside is: * Providing two features which were "want to have (but OK to defer)" when GPIO interfaces were first discussed in November 2006: - A "struct gpio_chip" to plug in GPIOs that aren't directly supported by SOC platforms, but come from FPGAs or other multifunction devices using conventional device registers (like UCB-1x00 or SM501 GPIOs, and southbridges in PCs with more open specs than usual). - Full support for message-based GPIO expanders, where registers are accessed through sleeping I/O calls. Previous support for these "cansleep" calls was just stubs. (One example: the widely used pcf8574 I2C chips, with 8 GPIOs each.) * Including a non-stub implementation of the gpio_{request,free}() calls, making those calls much more useful. The diagnostic labels are also recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot of all GPIOs known to this infrastructure. The driver programming interfaces introduced in 2.6.21 do not change at all; this infrastructure is entirely below those covers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 06:28:20 +00:00
return 0;
}
subsys_initcall(gpiolib_debugfs_init);
#endif /* DEBUG_FS */