linux/drivers/net/bonding/bond_main.c

5040 lines
133 KiB
C
Raw Normal View History

/*
* originally based on the dummy device.
*
* Copyright 1999, Thomas Davis, tadavis@lbl.gov.
* Licensed under the GPL. Based on dummy.c, and eql.c devices.
*
* bonding.c: an Ethernet Bonding driver
*
* This is useful to talk to a Cisco EtherChannel compatible equipment:
* Cisco 5500
* Sun Trunking (Solaris)
* Alteon AceDirector Trunks
* Linux Bonding
* and probably many L2 switches ...
*
* How it works:
* ifconfig bond0 ipaddress netmask up
* will setup a network device, with an ip address. No mac address
* will be assigned at this time. The hw mac address will come from
* the first slave bonded to the channel. All slaves will then use
* this hw mac address.
*
* ifconfig bond0 down
* will release all slaves, marking them as down.
*
* ifenslave bond0 eth0
* will attach eth0 to bond0 as a slave. eth0 hw mac address will either
* a: be used as initial mac address
* b: if a hw mac address already is there, eth0's hw mac address
* will then be set from bond0.
*
*/
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/types.h>
#include <linux/fcntl.h>
#include <linux/interrupt.h>
#include <linux/ptrace.h>
#include <linux/ioport.h>
#include <linux/in.h>
#include <net/ip.h>
#include <linux/ip.h>
#include <linux/tcp.h>
#include <linux/udp.h>
#include <linux/slab.h>
#include <linux/string.h>
#include <linux/init.h>
#include <linux/timer.h>
#include <linux/socket.h>
#include <linux/ctype.h>
#include <linux/inet.h>
#include <linux/bitops.h>
#include <linux/io.h>
#include <asm/dma.h>
#include <linux/uaccess.h>
#include <linux/errno.h>
#include <linux/netdevice.h>
#include <linux/inetdevice.h>
#include <linux/igmp.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <net/sock.h>
#include <linux/rtnetlink.h>
#include <linux/smp.h>
#include <linux/if_ether.h>
#include <net/arp.h>
#include <linux/mii.h>
#include <linux/ethtool.h>
#include <linux/if_vlan.h>
#include <linux/if_bonding.h>
#include <linux/jiffies.h>
#include <linux/preempt.h>
#include <net/route.h>
#include <net/net_namespace.h>
#include <net/netns/generic.h>
bonding: Fix corrupted queue_mapping In the transmit path of the bonding driver, skb->cb is used to stash the skb->queue_mapping so that the bonding device can set its own queue mapping. This value becomes corrupted since the skb->cb is also used in __dev_xmit_skb. When transmitting through bonding driver, bond_select_queue is called from dev_queue_xmit. In bond_select_queue the original skb->queue_mapping is copied into skb->cb (via bond_queue_mapping) and skb->queue_mapping is overwritten with the bond driver queue. Subsequently in dev_queue_xmit, __dev_xmit_skb is called which writes the packet length into skb->cb, thereby overwriting the stashed queue mappping. In bond_dev_queue_xmit (called from hard_start_xmit), the queue mapping for the skb is set to the stashed value which is now the skb length and hence is an invalid queue for the slave device. If we want to save skb->queue_mapping into skb->cb[], best place is to add a field in struct qdisc_skb_cb, to make sure it wont conflict with other layers (eg : Qdiscc, Infiniband...) This patchs also makes sure (struct qdisc_skb_cb)->data is aligned on 8 bytes : netem qdisc for example assumes it can store an u64 in it, without misalignment penalty. Note : we only have 20 bytes left in (struct qdisc_skb_cb)->data[]. The largest user is CHOKe and it fills it. Based on a previous patch from Tom Herbert. Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Tom Herbert <therbert@google.com> Cc: John Fastabend <john.r.fastabend@intel.com> Cc: Roland Dreier <roland@kernel.org> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-12 06:03:51 +00:00
#include <net/pkt_sched.h>
#include "bonding.h"
#include "bond_3ad.h"
#include "bond_alb.h"
/*---------------------------- Module parameters ----------------------------*/
/* monitor all links that often (in milliseconds). <=0 disables monitoring */
#define BOND_LINK_MON_INTERV 0
#define BOND_LINK_ARP_INTERV 0
static int max_bonds = BOND_DEFAULT_MAX_BONDS;
bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 08:40:18 +00:00
static int tx_queues = BOND_DEFAULT_TX_QUEUES;
static int num_peer_notif = 1;
static int miimon = BOND_LINK_MON_INTERV;
static int updelay;
static int downdelay;
static int use_carrier = 1;
static char *mode;
static char *primary;
static char *primary_reselect;
static char *lacp_rate;
static int min_links;
static char *ad_select;
static char *xmit_hash_policy;
static int arp_interval = BOND_LINK_ARP_INTERV;
static char *arp_ip_target[BOND_MAX_ARP_TARGETS];
static char *arp_validate;
static char *fail_over_mac;
static int all_slaves_active = 0;
static struct bond_params bonding_defaults;
static int resend_igmp = BOND_DEFAULT_RESEND_IGMP;
module_param(max_bonds, int, 0);
MODULE_PARM_DESC(max_bonds, "Max number of bonded devices");
bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 08:40:18 +00:00
module_param(tx_queues, int, 0);
MODULE_PARM_DESC(tx_queues, "Max number of transmit queues (default = 16)");
module_param_named(num_grat_arp, num_peer_notif, int, 0644);
MODULE_PARM_DESC(num_grat_arp, "Number of peer notifications to send on "
"failover event (alias of num_unsol_na)");
module_param_named(num_unsol_na, num_peer_notif, int, 0644);
MODULE_PARM_DESC(num_unsol_na, "Number of peer notifications to send on "
"failover event (alias of num_grat_arp)");
module_param(miimon, int, 0);
MODULE_PARM_DESC(miimon, "Link check interval in milliseconds");
module_param(updelay, int, 0);
MODULE_PARM_DESC(updelay, "Delay before considering link up, in milliseconds");
module_param(downdelay, int, 0);
MODULE_PARM_DESC(downdelay, "Delay before considering link down, "
"in milliseconds");
module_param(use_carrier, int, 0);
MODULE_PARM_DESC(use_carrier, "Use netif_carrier_ok (vs MII ioctls) in miimon; "
"0 for off, 1 for on (default)");
module_param(mode, charp, 0);
MODULE_PARM_DESC(mode, "Mode of operation; 0 for balance-rr, "
"1 for active-backup, 2 for balance-xor, "
"3 for broadcast, 4 for 802.3ad, 5 for balance-tlb, "
"6 for balance-alb");
module_param(primary, charp, 0);
MODULE_PARM_DESC(primary, "Primary network device to use");
module_param(primary_reselect, charp, 0);
MODULE_PARM_DESC(primary_reselect, "Reselect primary slave "
"once it comes up; "
"0 for always (default), "
"1 for only if speed of primary is "
"better, "
"2 for only on active slave "
"failure");
module_param(lacp_rate, charp, 0);
MODULE_PARM_DESC(lacp_rate, "LACPDU tx rate to request from 802.3ad partner; "
"0 for slow, 1 for fast");
module_param(ad_select, charp, 0);
MODULE_PARM_DESC(ad_select, "803.ad aggregation selection logic; "
"0 for stable (default), 1 for bandwidth, "
"2 for count");
module_param(min_links, int, 0);
MODULE_PARM_DESC(min_links, "Minimum number of available links before turning on carrier");
module_param(xmit_hash_policy, charp, 0);
MODULE_PARM_DESC(xmit_hash_policy, "balance-xor and 802.3ad hashing method; "
"0 for layer 2 (default), 1 for layer 3+4, "
"2 for layer 2+3");
module_param(arp_interval, int, 0);
MODULE_PARM_DESC(arp_interval, "arp interval in milliseconds");
module_param_array(arp_ip_target, charp, NULL, 0);
MODULE_PARM_DESC(arp_ip_target, "arp targets in n.n.n.n form");
module_param(arp_validate, charp, 0);
MODULE_PARM_DESC(arp_validate, "validate src/dst of ARP probes; "
"0 for none (default), 1 for active, "
"2 for backup, 3 for all");
module_param(fail_over_mac, charp, 0);
MODULE_PARM_DESC(fail_over_mac, "For active-backup, do not set all slaves to "
"the same MAC; 0 for none (default), "
"1 for active, 2 for follow");
module_param(all_slaves_active, int, 0);
MODULE_PARM_DESC(all_slaves_active, "Keep all frames received on an interface"
"by setting active flag for all slaves; "
"0 for never (default), 1 for always.");
module_param(resend_igmp, int, 0);
MODULE_PARM_DESC(resend_igmp, "Number of IGMP membership reports to send on "
"link failure");
/*----------------------------- Global variables ----------------------------*/
#ifdef CONFIG_NET_POLL_CONTROLLER
net: Convert netpoll blocking api in bonding driver to be a counter A while back I made some changes to enable netpoll in the bonding driver. Among them was a per-cpu flag that indicated we were in a path that held locks which could cause the netpoll path to block in during tx, and as such the tx path should queue the frame for later use. This appears to have given rise to a regression. If one of those paths on which we hold the per-cpu flag yields the cpu, its possible for us to come back on a different cpu, leading to us clearing a different flag than we set. This results in odd netpoll drops, and BUG backtraces appearing in the log, as we check to make sure that we only clear set bits, and only set clear bits. I had though briefly about changing the offending paths so that they wouldn't sleep, but looking at my origional work more closely, it doesn't appear that a per-cpu flag is warranted. We alrady gate the checking of this flag on IFF_IN_NETPOLL, so we don't hit this in the normal tx case anyway. And practically speaking, the normal use case for netpoll is to only have one client anyway, so we're not going to erroneously queue netpoll frames when its actually safe to do so. As such, lets just convert that per-cpu flag to an atomic counter. It fixes the rescheduling bugs, is equivalent from a performance perspective and actually eliminates some code in the process. Tested by the reporter and myself, successfully Reported-by: Liang Zheng <lzheng@redhat.com> CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: David S. Miller <davem@davemloft.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-06 09:05:50 +00:00
atomic_t netpoll_block_tx = ATOMIC_INIT(0);
#endif
int bond_net_id __read_mostly;
static __be32 arp_target[BOND_MAX_ARP_TARGETS];
static int arp_ip_count;
static int bond_mode = BOND_MODE_ROUNDROBIN;
static int xmit_hashtype = BOND_XMIT_POLICY_LAYER2;
static int lacp_fast;
const struct bond_parm_tbl bond_lacp_tbl[] = {
{ "slow", AD_LACP_SLOW},
{ "fast", AD_LACP_FAST},
{ NULL, -1},
};
const struct bond_parm_tbl bond_mode_tbl[] = {
{ "balance-rr", BOND_MODE_ROUNDROBIN},
{ "active-backup", BOND_MODE_ACTIVEBACKUP},
{ "balance-xor", BOND_MODE_XOR},
{ "broadcast", BOND_MODE_BROADCAST},
{ "802.3ad", BOND_MODE_8023AD},
{ "balance-tlb", BOND_MODE_TLB},
{ "balance-alb", BOND_MODE_ALB},
{ NULL, -1},
};
const struct bond_parm_tbl xmit_hashtype_tbl[] = {
{ "layer2", BOND_XMIT_POLICY_LAYER2},
{ "layer3+4", BOND_XMIT_POLICY_LAYER34},
{ "layer2+3", BOND_XMIT_POLICY_LAYER23},
{ NULL, -1},
};
const struct bond_parm_tbl arp_validate_tbl[] = {
{ "none", BOND_ARP_VALIDATE_NONE},
{ "active", BOND_ARP_VALIDATE_ACTIVE},
{ "backup", BOND_ARP_VALIDATE_BACKUP},
{ "all", BOND_ARP_VALIDATE_ALL},
{ NULL, -1},
};
const struct bond_parm_tbl fail_over_mac_tbl[] = {
{ "none", BOND_FOM_NONE},
{ "active", BOND_FOM_ACTIVE},
{ "follow", BOND_FOM_FOLLOW},
{ NULL, -1},
};
const struct bond_parm_tbl pri_reselect_tbl[] = {
{ "always", BOND_PRI_RESELECT_ALWAYS},
{ "better", BOND_PRI_RESELECT_BETTER},
{ "failure", BOND_PRI_RESELECT_FAILURE},
{ NULL, -1},
};
struct bond_parm_tbl ad_select_tbl[] = {
{ "stable", BOND_AD_STABLE},
{ "bandwidth", BOND_AD_BANDWIDTH},
{ "count", BOND_AD_COUNT},
{ NULL, -1},
};
/*-------------------------- Forward declarations ---------------------------*/
static int bond_init(struct net_device *bond_dev);
static void bond_uninit(struct net_device *bond_dev);
/*---------------------------- General routines -----------------------------*/
const char *bond_mode_name(int mode)
{
static const char *names[] = {
[BOND_MODE_ROUNDROBIN] = "load balancing (round-robin)",
[BOND_MODE_ACTIVEBACKUP] = "fault-tolerance (active-backup)",
[BOND_MODE_XOR] = "load balancing (xor)",
[BOND_MODE_BROADCAST] = "fault-tolerance (broadcast)",
[BOND_MODE_8023AD] = "IEEE 802.3ad Dynamic link aggregation",
[BOND_MODE_TLB] = "transmit load balancing",
[BOND_MODE_ALB] = "adaptive load balancing",
};
if (mode < 0 || mode > BOND_MODE_ALB)
return "unknown";
return names[mode];
}
/*---------------------------------- VLAN -----------------------------------*/
/**
* bond_add_vlan - add a new vlan id on bond
* @bond: bond that got the notification
* @vlan_id: the vlan id to add
*
* Returns -ENOMEM if allocation failed.
*/
static int bond_add_vlan(struct bonding *bond, unsigned short vlan_id)
{
struct vlan_entry *vlan;
pr_debug("bond: %s, vlan id %d\n",
(bond ? bond->dev->name : "None"), vlan_id);
vlan = kzalloc(sizeof(struct vlan_entry), GFP_KERNEL);
if (!vlan)
return -ENOMEM;
INIT_LIST_HEAD(&vlan->vlan_list);
vlan->vlan_id = vlan_id;
write_lock_bh(&bond->lock);
list_add_tail(&vlan->vlan_list, &bond->vlan_list);
write_unlock_bh(&bond->lock);
pr_debug("added VLAN ID %d on bond %s\n", vlan_id, bond->dev->name);
return 0;
}
/**
* bond_del_vlan - delete a vlan id from bond
* @bond: bond that got the notification
* @vlan_id: the vlan id to delete
*
* returns -ENODEV if @vlan_id was not found in @bond.
*/
static int bond_del_vlan(struct bonding *bond, unsigned short vlan_id)
{
struct vlan_entry *vlan;
int res = -ENODEV;
pr_debug("bond: %s, vlan id %d\n", bond->dev->name, vlan_id);
block_netpoll_tx();
write_lock_bh(&bond->lock);
list_for_each_entry(vlan, &bond->vlan_list, vlan_list) {
if (vlan->vlan_id == vlan_id) {
list_del(&vlan->vlan_list);
if (bond_is_lb(bond))
bond_alb_clear_vlan(bond, vlan_id);
pr_debug("removed VLAN ID %d from bond %s\n",
vlan_id, bond->dev->name);
kfree(vlan);
res = 0;
goto out;
}
}
pr_debug("couldn't find VLAN ID %d in bond %s\n",
vlan_id, bond->dev->name);
out:
write_unlock_bh(&bond->lock);
unblock_netpoll_tx();
return res;
}
/**
* bond_next_vlan - safely skip to the next item in the vlans list.
* @bond: the bond we're working on
* @curr: item we're advancing from
*
* Returns %NULL if list is empty, bond->next_vlan if @curr is %NULL,
* or @curr->next otherwise (even if it is @curr itself again).
*
* Caller must hold bond->lock
*/
struct vlan_entry *bond_next_vlan(struct bonding *bond, struct vlan_entry *curr)
{
struct vlan_entry *next, *last;
if (list_empty(&bond->vlan_list))
return NULL;
if (!curr) {
next = list_entry(bond->vlan_list.next,
struct vlan_entry, vlan_list);
} else {
last = list_entry(bond->vlan_list.prev,
struct vlan_entry, vlan_list);
if (last == curr) {
next = list_entry(bond->vlan_list.next,
struct vlan_entry, vlan_list);
} else {
next = list_entry(curr->vlan_list.next,
struct vlan_entry, vlan_list);
}
}
return next;
}
/**
* bond_dev_queue_xmit - Prepare skb for xmit.
*
* @bond: bond device that got this skb for tx.
* @skb: hw accel VLAN tagged skb to transmit
* @slave_dev: slave that is supposed to xmit this skbuff
*/
int bond_dev_queue_xmit(struct bonding *bond, struct sk_buff *skb,
struct net_device *slave_dev)
{
skb->dev = slave_dev;
bonding: Fix corrupted queue_mapping In the transmit path of the bonding driver, skb->cb is used to stash the skb->queue_mapping so that the bonding device can set its own queue mapping. This value becomes corrupted since the skb->cb is also used in __dev_xmit_skb. When transmitting through bonding driver, bond_select_queue is called from dev_queue_xmit. In bond_select_queue the original skb->queue_mapping is copied into skb->cb (via bond_queue_mapping) and skb->queue_mapping is overwritten with the bond driver queue. Subsequently in dev_queue_xmit, __dev_xmit_skb is called which writes the packet length into skb->cb, thereby overwriting the stashed queue mappping. In bond_dev_queue_xmit (called from hard_start_xmit), the queue mapping for the skb is set to the stashed value which is now the skb length and hence is an invalid queue for the slave device. If we want to save skb->queue_mapping into skb->cb[], best place is to add a field in struct qdisc_skb_cb, to make sure it wont conflict with other layers (eg : Qdiscc, Infiniband...) This patchs also makes sure (struct qdisc_skb_cb)->data is aligned on 8 bytes : netem qdisc for example assumes it can store an u64 in it, without misalignment penalty. Note : we only have 20 bytes left in (struct qdisc_skb_cb)->data[]. The largest user is CHOKe and it fills it. Based on a previous patch from Tom Herbert. Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Tom Herbert <therbert@google.com> Cc: John Fastabend <john.r.fastabend@intel.com> Cc: Roland Dreier <roland@kernel.org> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-12 06:03:51 +00:00
BUILD_BUG_ON(sizeof(skb->queue_mapping) !=
sizeof(qdisc_skb_cb(skb)->slave_dev_queue_mapping));
skb->queue_mapping = qdisc_skb_cb(skb)->slave_dev_queue_mapping;
if (unlikely(netpoll_tx_running(bond->dev)))
bond_netpoll_send_skb(bond_get_slave_by_dev(bond, slave_dev), skb);
else
dev_queue_xmit(skb);
return 0;
}
/*
* In the following 2 functions, bond_vlan_rx_add_vid and bond_vlan_rx_kill_vid,
* We don't protect the slave list iteration with a lock because:
* a. This operation is performed in IOCTL context,
* b. The operation is protected by the RTNL semaphore in the 8021q code,
* c. Holding a lock with BH disabled while directly calling a base driver
* entry point is generally a BAD idea.
*
* The design of synchronization/protection for this operation in the 8021q
* module is good for one or more VLAN devices over a single physical device
* and cannot be extended for a teaming solution like bonding, so there is a
* potential race condition here where a net device from the vlan group might
* be referenced (either by a base driver or the 8021q code) while it is being
* removed from the system. However, it turns out we're not making matters
* worse, and if it works for regular VLAN usage it will work here too.
*/
/**
* bond_vlan_rx_add_vid - Propagates adding an id to slaves
* @bond_dev: bonding net device that got called
* @vid: vlan id being added
*/
static int bond_vlan_rx_add_vid(struct net_device *bond_dev, uint16_t vid)
{
struct bonding *bond = netdev_priv(bond_dev);
struct slave *slave, *stop_at;
int i, res;
bond_for_each_slave(bond, slave, i) {
res = vlan_vid_add(slave->dev, vid);
if (res)
goto unwind;
}
res = bond_add_vlan(bond, vid);
if (res) {
pr_err("%s: Error: Failed to add vlan id %d\n",
bond_dev->name, vid);
return res;
}
return 0;
unwind:
/* unwind from head to the slave that failed */
stop_at = slave;
bond_for_each_slave_from_to(bond, slave, i, bond->first_slave, stop_at)
vlan_vid_del(slave->dev, vid);
return res;
}
/**
* bond_vlan_rx_kill_vid - Propagates deleting an id to slaves
* @bond_dev: bonding net device that got called
* @vid: vlan id being removed
*/
static int bond_vlan_rx_kill_vid(struct net_device *bond_dev, uint16_t vid)
{
struct bonding *bond = netdev_priv(bond_dev);
struct slave *slave;
int i, res;
bond_for_each_slave(bond, slave, i)
vlan_vid_del(slave->dev, vid);
res = bond_del_vlan(bond, vid);
if (res) {
pr_err("%s: Error: Failed to remove vlan id %d\n",
bond_dev->name, vid);
return res;
}
return 0;
}
static void bond_add_vlans_on_slave(struct bonding *bond, struct net_device *slave_dev)
{
struct vlan_entry *vlan;
int res;
list_for_each_entry(vlan, &bond->vlan_list, vlan_list) {
res = vlan_vid_add(slave_dev, vlan->vlan_id);
if (res)
pr_warning("%s: Failed to add vlan id %d to device %s\n",
bond->dev->name, vlan->vlan_id,
slave_dev->name);
}
}
static void bond_del_vlans_from_slave(struct bonding *bond,
struct net_device *slave_dev)
{
struct vlan_entry *vlan;
list_for_each_entry(vlan, &bond->vlan_list, vlan_list) {
if (!vlan->vlan_id)
continue;
vlan_vid_del(slave_dev, vlan->vlan_id);
}
}
/*------------------------------- Link status -------------------------------*/
/*
* Set the carrier state for the master according to the state of its
* slaves. If any slaves are up, the master is up. In 802.3ad mode,
* do special 802.3ad magic.
*
* Returns zero if carrier state does not change, nonzero if it does.
*/
static int bond_set_carrier(struct bonding *bond)
{
struct slave *slave;
int i;
if (bond->slave_cnt == 0)
goto down;
if (bond->params.mode == BOND_MODE_8023AD)
return bond_3ad_set_carrier(bond);
bond_for_each_slave(bond, slave, i) {
if (slave->link == BOND_LINK_UP) {
if (!netif_carrier_ok(bond->dev)) {
netif_carrier_on(bond->dev);
return 1;
}
return 0;
}
}
down:
if (netif_carrier_ok(bond->dev)) {
netif_carrier_off(bond->dev);
return 1;
}
return 0;
}
/*
* Get link speed and duplex from the slave's base driver
* using ethtool. If for some reason the call fails or the
* values are invalid, set speed and duplex to -1,
* and return.
*/
static void bond_update_speed_duplex(struct slave *slave)
{
struct net_device *slave_dev = slave->dev;
struct ethtool_cmd ecmd;
u32 slave_speed;
int res;
slave->speed = SPEED_UNKNOWN;
slave->duplex = DUPLEX_UNKNOWN;
res = __ethtool_get_settings(slave_dev, &ecmd);
if (res < 0)
return;
slave_speed = ethtool_cmd_speed(&ecmd);
if (slave_speed == 0 || slave_speed == ((__u32) -1))
return;
switch (ecmd.duplex) {
case DUPLEX_FULL:
case DUPLEX_HALF:
break;
default:
return;
}
slave->speed = slave_speed;
slave->duplex = ecmd.duplex;
return;
}
/*
* if <dev> supports MII link status reporting, check its link status.
*
* We either do MII/ETHTOOL ioctls, or check netif_carrier_ok(),
* depending upon the setting of the use_carrier parameter.
*
* Return either BMSR_LSTATUS, meaning that the link is up (or we
* can't tell and just pretend it is), or 0, meaning that the link is
* down.
*
* If reporting is non-zero, instead of faking link up, return -1 if
* both ETHTOOL and MII ioctls fail (meaning the device does not
* support them). If use_carrier is set, return whatever it says.
* It'd be nice if there was a good way to tell if a driver supports
* netif_carrier, but there really isn't.
*/
static int bond_check_dev_link(struct bonding *bond,
struct net_device *slave_dev, int reporting)
{
const struct net_device_ops *slave_ops = slave_dev->netdev_ops;
int (*ioctl)(struct net_device *, struct ifreq *, int);
struct ifreq ifr;
struct mii_ioctl_data *mii;
if (!reporting && !netif_running(slave_dev))
return 0;
if (bond->params.use_carrier)
return netif_carrier_ok(slave_dev) ? BMSR_LSTATUS : 0;
/* Try to get link status using Ethtool first. */
if (slave_dev->ethtool_ops) {
if (slave_dev->ethtool_ops->get_link) {
u32 link;
link = slave_dev->ethtool_ops->get_link(slave_dev);
return link ? BMSR_LSTATUS : 0;
}
}
/* Ethtool can't be used, fallback to MII ioctls. */
ioctl = slave_ops->ndo_do_ioctl;
if (ioctl) {
/* TODO: set pointer to correct ioctl on a per team member */
/* bases to make this more efficient. that is, once */
/* we determine the correct ioctl, we will always */
/* call it and not the others for that team */
/* member. */
/*
* We cannot assume that SIOCGMIIPHY will also read a
* register; not all network drivers (e.g., e100)
* support that.
*/
/* Yes, the mii is overlaid on the ifreq.ifr_ifru */
strncpy(ifr.ifr_name, slave_dev->name, IFNAMSIZ);
mii = if_mii(&ifr);
if (IOCTL(slave_dev, &ifr, SIOCGMIIPHY) == 0) {
mii->reg_num = MII_BMSR;
if (IOCTL(slave_dev, &ifr, SIOCGMIIREG) == 0)
return mii->val_out & BMSR_LSTATUS;
}
}
/*
* If reporting, report that either there's no dev->do_ioctl,
* or both SIOCGMIIREG and get_link failed (meaning that we
* cannot report link status). If not reporting, pretend
* we're ok.
*/
return reporting ? -1 : BMSR_LSTATUS;
}
/*----------------------------- Multicast list ------------------------------*/
/*
* Push the promiscuity flag down to appropriate slaves
*/
static int bond_set_promiscuity(struct bonding *bond, int inc)
{
int err = 0;
if (USES_PRIMARY(bond->params.mode)) {
/* write lock already acquired */
if (bond->curr_active_slave) {
err = dev_set_promiscuity(bond->curr_active_slave->dev,
inc);
}
} else {
struct slave *slave;
int i;
bond_for_each_slave(bond, slave, i) {
err = dev_set_promiscuity(slave->dev, inc);
if (err)
return err;
}
}
return err;
}
/*
* Push the allmulti flag down to all slaves
*/
static int bond_set_allmulti(struct bonding *bond, int inc)
{
int err = 0;
if (USES_PRIMARY(bond->params.mode)) {
/* write lock already acquired */
if (bond->curr_active_slave) {
err = dev_set_allmulti(bond->curr_active_slave->dev,
inc);
}
} else {
struct slave *slave;
int i;
bond_for_each_slave(bond, slave, i) {
err = dev_set_allmulti(slave->dev, inc);
if (err)
return err;
}
}
return err;
}
/*
* Add a Multicast address to slaves
* according to mode
*/
static void bond_mc_add(struct bonding *bond, void *addr)
{
if (USES_PRIMARY(bond->params.mode)) {
/* write lock already acquired */
if (bond->curr_active_slave)
dev_mc_add(bond->curr_active_slave->dev, addr);
} else {
struct slave *slave;
int i;
bond_for_each_slave(bond, slave, i)
dev_mc_add(slave->dev, addr);
}
}
/*
* Remove a multicast address from slave
* according to mode
*/
static void bond_mc_del(struct bonding *bond, void *addr)
{
if (USES_PRIMARY(bond->params.mode)) {
/* write lock already acquired */
if (bond->curr_active_slave)
dev_mc_del(bond->curr_active_slave->dev, addr);
} else {
struct slave *slave;
int i;
bond_for_each_slave(bond, slave, i) {
dev_mc_del(slave->dev, addr);
}
}
}
static void __bond_resend_igmp_join_requests(struct net_device *dev)
{
struct in_device *in_dev;
rcu_read_lock();
in_dev = __in_dev_get_rcu(dev);
if (in_dev)
ip_mc_rejoin_groups(in_dev);
rcu_read_unlock();
}
/*
* Retrieve the list of registered multicast addresses for the bonding
* device and retransmit an IGMP JOIN request to the current active
* slave.
*/
static void bond_resend_igmp_join_requests(struct bonding *bond)
{
struct net_device *bond_dev, *vlan_dev, *master_dev;
struct vlan_entry *vlan;
read_lock(&bond->lock);
bond_dev = bond->dev;
/* rejoin all groups on bond device */
__bond_resend_igmp_join_requests(bond_dev);
/*
* if bond is enslaved to a bridge,
* then rejoin all groups on its master
*/
master_dev = bond_dev->master;
if (master_dev)
if ((master_dev->priv_flags & IFF_EBRIDGE)
&& (bond_dev->priv_flags & IFF_BRIDGE_PORT))
__bond_resend_igmp_join_requests(master_dev);
/* rejoin all groups on vlan devices */
list_for_each_entry(vlan, &bond->vlan_list, vlan_list) {
rcu_read_lock();
vlan_dev = __vlan_find_dev_deep(bond_dev,
vlan->vlan_id);
rcu_read_unlock();
if (vlan_dev)
__bond_resend_igmp_join_requests(vlan_dev);
}
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
if (--bond->igmp_retrans > 0)
queue_delayed_work(bond->wq, &bond->mcast_work, HZ/5);
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
read_unlock(&bond->lock);
}
static void bond_resend_igmp_join_requests_delayed(struct work_struct *work)
{
struct bonding *bond = container_of(work, struct bonding,
mcast_work.work);
bond_resend_igmp_join_requests(bond);
}
/*
* flush all members of flush->mc_list from device dev->mc_list
*/
static void bond_mc_list_flush(struct net_device *bond_dev,
struct net_device *slave_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
struct netdev_hw_addr *ha;
netdev_for_each_mc_addr(ha, bond_dev)
dev_mc_del(slave_dev, ha->addr);
if (bond->params.mode == BOND_MODE_8023AD) {
/* del lacpdu mc addr from mc list */
u8 lacpdu_multicast[ETH_ALEN] = MULTICAST_LACPDU_ADDR;
dev_mc_del(slave_dev, lacpdu_multicast);
}
}
/*--------------------------- Active slave change ---------------------------*/
/*
* Update the mc list and multicast-related flags for the new and
* old active slaves (if any) according to the multicast mode, and
* promiscuous flags unconditionally.
*/
static void bond_mc_swap(struct bonding *bond, struct slave *new_active,
struct slave *old_active)
{
struct netdev_hw_addr *ha;
if (!USES_PRIMARY(bond->params.mode))
/* nothing to do - mc list is already up-to-date on
* all slaves
*/
return;
if (old_active) {
if (bond->dev->flags & IFF_PROMISC)
dev_set_promiscuity(old_active->dev, -1);
if (bond->dev->flags & IFF_ALLMULTI)
dev_set_allmulti(old_active->dev, -1);
netdev_for_each_mc_addr(ha, bond->dev)
dev_mc_del(old_active->dev, ha->addr);
}
if (new_active) {
/* FIXME: Signal errors upstream. */
if (bond->dev->flags & IFF_PROMISC)
dev_set_promiscuity(new_active->dev, 1);
if (bond->dev->flags & IFF_ALLMULTI)
dev_set_allmulti(new_active->dev, 1);
netdev_for_each_mc_addr(ha, bond->dev)
dev_mc_add(new_active->dev, ha->addr);
}
}
/*
* bond_do_fail_over_mac
*
* Perform special MAC address swapping for fail_over_mac settings
*
* Called with RTNL, bond->lock for read, curr_slave_lock for write_bh.
*/
static void bond_do_fail_over_mac(struct bonding *bond,
struct slave *new_active,
struct slave *old_active)
__releases(&bond->curr_slave_lock)
__releases(&bond->lock)
__acquires(&bond->lock)
__acquires(&bond->curr_slave_lock)
{
u8 tmp_mac[ETH_ALEN];
struct sockaddr saddr;
int rv;
switch (bond->params.fail_over_mac) {
case BOND_FOM_ACTIVE:
if (new_active) {
memcpy(bond->dev->dev_addr, new_active->dev->dev_addr,
new_active->dev->addr_len);
write_unlock_bh(&bond->curr_slave_lock);
read_unlock(&bond->lock);
call_netdevice_notifiers(NETDEV_CHANGEADDR, bond->dev);
read_lock(&bond->lock);
write_lock_bh(&bond->curr_slave_lock);
}
break;
case BOND_FOM_FOLLOW:
/*
* if new_active && old_active, swap them
* if just old_active, do nothing (going to no active slave)
* if just new_active, set new_active to bond's MAC
*/
if (!new_active)
return;
write_unlock_bh(&bond->curr_slave_lock);
read_unlock(&bond->lock);
if (old_active) {
memcpy(tmp_mac, new_active->dev->dev_addr, ETH_ALEN);
memcpy(saddr.sa_data, old_active->dev->dev_addr,
ETH_ALEN);
saddr.sa_family = new_active->dev->type;
} else {
memcpy(saddr.sa_data, bond->dev->dev_addr, ETH_ALEN);
saddr.sa_family = bond->dev->type;
}
rv = dev_set_mac_address(new_active->dev, &saddr);
if (rv) {
pr_err("%s: Error %d setting MAC of slave %s\n",
bond->dev->name, -rv, new_active->dev->name);
goto out;
}
if (!old_active)
goto out;
memcpy(saddr.sa_data, tmp_mac, ETH_ALEN);
saddr.sa_family = old_active->dev->type;
rv = dev_set_mac_address(old_active->dev, &saddr);
if (rv)
pr_err("%s: Error %d setting MAC of slave %s\n",
bond->dev->name, -rv, new_active->dev->name);
out:
read_lock(&bond->lock);
write_lock_bh(&bond->curr_slave_lock);
break;
default:
pr_err("%s: bond_do_fail_over_mac impossible: bad policy %d\n",
bond->dev->name, bond->params.fail_over_mac);
break;
}
}
static bool bond_should_change_active(struct bonding *bond)
{
struct slave *prim = bond->primary_slave;
struct slave *curr = bond->curr_active_slave;
if (!prim || !curr || curr->link != BOND_LINK_UP)
return true;
if (bond->force_primary) {
bond->force_primary = false;
return true;
}
if (bond->params.primary_reselect == BOND_PRI_RESELECT_BETTER &&
(prim->speed < curr->speed ||
(prim->speed == curr->speed && prim->duplex <= curr->duplex)))
return false;
if (bond->params.primary_reselect == BOND_PRI_RESELECT_FAILURE)
return false;
return true;
}
/**
* find_best_interface - select the best available slave to be the active one
* @bond: our bonding struct
*
* Warning: Caller must hold curr_slave_lock for writing.
*/
static struct slave *bond_find_best_slave(struct bonding *bond)
{
struct slave *new_active, *old_active;
struct slave *bestslave = NULL;
int mintime = bond->params.updelay;
int i;
new_active = bond->curr_active_slave;
if (!new_active) { /* there were no active slaves left */
if (bond->slave_cnt > 0) /* found one slave */
new_active = bond->first_slave;
else
return NULL; /* still no slave, return NULL */
}
if ((bond->primary_slave) &&
bond->primary_slave->link == BOND_LINK_UP &&
bond_should_change_active(bond)) {
new_active = bond->primary_slave;
}
/* remember where to stop iterating over the slaves */
old_active = new_active;
bond_for_each_slave_from(bond, new_active, i, old_active) {
if (new_active->link == BOND_LINK_UP) {
return new_active;
} else if (new_active->link == BOND_LINK_BACK &&
IS_UP(new_active->dev)) {
/* link up, but waiting for stabilization */
if (new_active->delay < mintime) {
mintime = new_active->delay;
bestslave = new_active;
}
}
}
return bestslave;
}
static bool bond_should_notify_peers(struct bonding *bond)
{
struct slave *slave = bond->curr_active_slave;
pr_debug("bond_should_notify_peers: bond %s slave %s\n",
bond->dev->name, slave ? slave->dev->name : "NULL");
if (!slave || !bond->send_peer_notif ||
test_bit(__LINK_STATE_LINKWATCH_PENDING, &slave->dev->state))
return false;
bond->send_peer_notif--;
return true;
}
/**
* change_active_interface - change the active slave into the specified one
* @bond: our bonding struct
* @new: the new slave to make the active one
*
* Set the new slave to the bond's settings and unset them on the old
* curr_active_slave.
* Setting include flags, mc-list, promiscuity, allmulti, etc.
*
* If @new's link state is %BOND_LINK_BACK we'll set it to %BOND_LINK_UP,
* because it is apparently the best available slave we have, even though its
* updelay hasn't timed out yet.
*
* If new_active is not NULL, caller must hold bond->lock for read and
* curr_slave_lock for write_bh.
*/
void bond_change_active_slave(struct bonding *bond, struct slave *new_active)
{
struct slave *old_active = bond->curr_active_slave;
if (old_active == new_active)
return;
if (new_active) {
new_active->jiffies = jiffies;
if (new_active->link == BOND_LINK_BACK) {
if (USES_PRIMARY(bond->params.mode)) {
pr_info("%s: making interface %s the new active one %d ms earlier.\n",
bond->dev->name, new_active->dev->name,
(bond->params.updelay - new_active->delay) * bond->params.miimon);
}
new_active->delay = 0;
new_active->link = BOND_LINK_UP;
if (bond->params.mode == BOND_MODE_8023AD)
bond_3ad_handle_link_change(new_active, BOND_LINK_UP);
if (bond_is_lb(bond))
bond_alb_handle_link_change(bond, new_active, BOND_LINK_UP);
} else {
if (USES_PRIMARY(bond->params.mode)) {
pr_info("%s: making interface %s the new active one.\n",
bond->dev->name, new_active->dev->name);
}
}
}
if (USES_PRIMARY(bond->params.mode))
bond_mc_swap(bond, new_active, old_active);
if (bond_is_lb(bond)) {
bond_alb_handle_active_change(bond, new_active);
if (old_active)
bond_set_slave_inactive_flags(old_active);
if (new_active)
bond_set_slave_active_flags(new_active);
} else {
bond->curr_active_slave = new_active;
}
if (bond->params.mode == BOND_MODE_ACTIVEBACKUP) {
if (old_active)
bond_set_slave_inactive_flags(old_active);
if (new_active) {
bool should_notify_peers = false;
bond_set_slave_active_flags(new_active);
if (bond->params.fail_over_mac)
bond_do_fail_over_mac(bond, new_active,
old_active);
if (netif_running(bond->dev)) {
bond->send_peer_notif =
bond->params.num_peer_notif;
should_notify_peers =
bond_should_notify_peers(bond);
}
write_unlock_bh(&bond->curr_slave_lock);
read_unlock(&bond->lock);
call_netdevice_notifiers(NETDEV_BONDING_FAILOVER, bond->dev);
if (should_notify_peers)
call_netdevice_notifiers(NETDEV_NOTIFY_PEERS,
bond->dev);
read_lock(&bond->lock);
write_lock_bh(&bond->curr_slave_lock);
}
}
/* resend IGMP joins since active slave has changed or
* all were sent on curr_active_slave.
* resend only if bond is brought up with the affected
* bonding modes and the retransmission is enabled */
if (netif_running(bond->dev) && (bond->params.resend_igmp > 0) &&
((USES_PRIMARY(bond->params.mode) && new_active) ||
bond->params.mode == BOND_MODE_ROUNDROBIN)) {
bond->igmp_retrans = bond->params.resend_igmp;
queue_delayed_work(bond->wq, &bond->mcast_work, 0);
}
}
/**
* bond_select_active_slave - select a new active slave, if needed
* @bond: our bonding struct
*
* This functions should be called when one of the following occurs:
* - The old curr_active_slave has been released or lost its link.
* - The primary_slave has got its link back.
* - A slave has got its link back and there's no old curr_active_slave.
*
* Caller must hold bond->lock for read and curr_slave_lock for write_bh.
*/
void bond_select_active_slave(struct bonding *bond)
{
struct slave *best_slave;
int rv;
best_slave = bond_find_best_slave(bond);
if (best_slave != bond->curr_active_slave) {
bond_change_active_slave(bond, best_slave);
rv = bond_set_carrier(bond);
if (!rv)
return;
if (netif_carrier_ok(bond->dev)) {
pr_info("%s: first active interface up!\n",
bond->dev->name);
} else {
pr_info("%s: now running without any active interface !\n",
bond->dev->name);
}
}
}
/*--------------------------- slave list handling ---------------------------*/
/*
* This function attaches the slave to the end of list.
*
* bond->lock held for writing by caller.
*/
static void bond_attach_slave(struct bonding *bond, struct slave *new_slave)
{
if (bond->first_slave == NULL) { /* attaching the first slave */
new_slave->next = new_slave;
new_slave->prev = new_slave;
bond->first_slave = new_slave;
} else {
new_slave->next = bond->first_slave;
new_slave->prev = bond->first_slave->prev;
new_slave->next->prev = new_slave;
new_slave->prev->next = new_slave;
}
bond->slave_cnt++;
}
/*
* This function detaches the slave from the list.
* WARNING: no check is made to verify if the slave effectively
* belongs to <bond>.
* Nothing is freed on return, structures are just unchained.
* If any slave pointer in bond was pointing to <slave>,
* it should be changed by the calling function.
*
* bond->lock held for writing by caller.
*/
static void bond_detach_slave(struct bonding *bond, struct slave *slave)
{
if (slave->next)
slave->next->prev = slave->prev;
if (slave->prev)
slave->prev->next = slave->next;
if (bond->first_slave == slave) { /* slave is the first slave */
if (bond->slave_cnt > 1) { /* there are more slave */
bond->first_slave = slave->next;
} else {
bond->first_slave = NULL; /* slave was the last one */
}
}
slave->next = NULL;
slave->prev = NULL;
bond->slave_cnt--;
}
#ifdef CONFIG_NET_POLL_CONTROLLER
static inline int slave_enable_netpoll(struct slave *slave)
{
struct netpoll *np;
int err = 0;
np = kzalloc(sizeof(*np), GFP_ATOMIC);
err = -ENOMEM;
if (!np)
goto out;
err = __netpoll_setup(np, slave->dev, GFP_ATOMIC);
if (err) {
kfree(np);
goto out;
}
slave->np = np;
out:
return err;
}
static inline void slave_disable_netpoll(struct slave *slave)
{
struct netpoll *np = slave->np;
if (!np)
return;
slave->np = NULL;
__netpoll_free_rcu(np);
}
static inline bool slave_dev_support_netpoll(struct net_device *slave_dev)
{
if (slave_dev->priv_flags & IFF_DISABLE_NETPOLL)
return false;
if (!slave_dev->netdev_ops->ndo_poll_controller)
return false;
return true;
}
static void bond_poll_controller(struct net_device *bond_dev)
{
}
static void __bond_netpoll_cleanup(struct bonding *bond)
{
struct slave *slave;
int i;
bond_for_each_slave(bond, slave, i)
if (IS_UP(slave->dev))
slave_disable_netpoll(slave);
}
static void bond_netpoll_cleanup(struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
read_lock(&bond->lock);
__bond_netpoll_cleanup(bond);
read_unlock(&bond->lock);
}
static int bond_netpoll_setup(struct net_device *dev, struct netpoll_info *ni, gfp_t gfp)
{
struct bonding *bond = netdev_priv(dev);
struct slave *slave;
int i, err = 0;
read_lock(&bond->lock);
bond_for_each_slave(bond, slave, i) {
err = slave_enable_netpoll(slave);
if (err) {
__bond_netpoll_cleanup(bond);
break;
}
}
read_unlock(&bond->lock);
return err;
}
static struct netpoll_info *bond_netpoll_info(struct bonding *bond)
{
return bond->dev->npinfo;
}
#else
static inline int slave_enable_netpoll(struct slave *slave)
{
return 0;
}
static inline void slave_disable_netpoll(struct slave *slave)
{
}
static void bond_netpoll_cleanup(struct net_device *bond_dev)
{
}
#endif
/*---------------------------------- IOCTL ----------------------------------*/
static int bond_sethwaddr(struct net_device *bond_dev,
struct net_device *slave_dev)
{
pr_debug("bond_dev=%p\n", bond_dev);
pr_debug("slave_dev=%p\n", slave_dev);
pr_debug("slave_dev->addr_len=%d\n", slave_dev->addr_len);
memcpy(bond_dev->dev_addr, slave_dev->dev_addr, slave_dev->addr_len);
return 0;
}
static netdev_features_t bond_fix_features(struct net_device *dev,
netdev_features_t features)
{
struct slave *slave;
struct bonding *bond = netdev_priv(dev);
netdev_features_t mask;
int i;
read_lock(&bond->lock);
if (!bond->first_slave) {
/* Disable adding VLANs to empty bond. But why? --mq */
features |= NETIF_F_VLAN_CHALLENGED;
goto out;
}
mask = features;
features &= ~NETIF_F_ONE_FOR_ALL;
features |= NETIF_F_ALL_FOR_ALL;
bond_for_each_slave(bond, slave, i) {
features = netdev_increment_features(features,
slave->dev->features,
mask);
}
out:
read_unlock(&bond->lock);
return features;
}
#define BOND_VLAN_FEATURES (NETIF_F_ALL_CSUM | NETIF_F_SG | \
NETIF_F_FRAGLIST | NETIF_F_ALL_TSO | \
NETIF_F_HIGHDMA | NETIF_F_LRO)
static void bond_compute_features(struct bonding *bond)
{
struct slave *slave;
struct net_device *bond_dev = bond->dev;
netdev_features_t vlan_features = BOND_VLAN_FEATURES;
unsigned short max_hard_header_len = ETH_HLEN;
unsigned int gso_max_size = GSO_MAX_SIZE;
u16 gso_max_segs = GSO_MAX_SEGS;
int i;
unsigned int flags, dst_release_flag = IFF_XMIT_DST_RELEASE;
read_lock(&bond->lock);
if (!bond->first_slave)
goto done;
bond_for_each_slave(bond, slave, i) {
vlan_features = netdev_increment_features(vlan_features,
slave->dev->vlan_features, BOND_VLAN_FEATURES);
dst_release_flag &= slave->dev->priv_flags;
if (slave->dev->hard_header_len > max_hard_header_len)
max_hard_header_len = slave->dev->hard_header_len;
gso_max_size = min(gso_max_size, slave->dev->gso_max_size);
gso_max_segs = min(gso_max_segs, slave->dev->gso_max_segs);
}
done:
bond_dev->vlan_features = vlan_features;
bond_dev->hard_header_len = max_hard_header_len;
bond_dev->gso_max_segs = gso_max_segs;
netif_set_gso_max_size(bond_dev, gso_max_size);
flags = bond_dev->priv_flags & ~IFF_XMIT_DST_RELEASE;
bond_dev->priv_flags = flags | dst_release_flag;
read_unlock(&bond->lock);
netdev_change_features(bond_dev);
}
static void bond_setup_by_slave(struct net_device *bond_dev,
struct net_device *slave_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
bond_dev->header_ops = slave_dev->header_ops;
bond_dev->type = slave_dev->type;
bond_dev->hard_header_len = slave_dev->hard_header_len;
bond_dev->addr_len = slave_dev->addr_len;
memcpy(bond_dev->broadcast, slave_dev->broadcast,
slave_dev->addr_len);
bond->setup_by_slave = 1;
}
/* On bonding slaves other than the currently active slave, suppress
* duplicates except for alb non-mcast/bcast.
*/
static bool bond_should_deliver_exact_match(struct sk_buff *skb,
struct slave *slave,
struct bonding *bond)
{
if (bond_is_slave_inactive(slave)) {
if (bond->params.mode == BOND_MODE_ALB &&
skb->pkt_type != PACKET_BROADCAST &&
skb->pkt_type != PACKET_MULTICAST)
return false;
return true;
}
return false;
}
static rx_handler_result_t bond_handle_frame(struct sk_buff **pskb)
{
struct sk_buff *skb = *pskb;
struct slave *slave;
struct bonding *bond;
int (*recv_probe)(const struct sk_buff *, struct bonding *,
struct slave *);
int ret = RX_HANDLER_ANOTHER;
skb = skb_share_check(skb, GFP_ATOMIC);
if (unlikely(!skb))
return RX_HANDLER_CONSUMED;
*pskb = skb;
slave = bond_slave_get_rcu(skb->dev);
bond = slave->bond;
if (bond->params.arp_interval)
slave->dev->last_rx = jiffies;
recv_probe = ACCESS_ONCE(bond->recv_probe);
if (recv_probe) {
ret = recv_probe(skb, bond, slave);
if (ret == RX_HANDLER_CONSUMED) {
consume_skb(skb);
return ret;
}
}
if (bond_should_deliver_exact_match(skb, slave, bond)) {
return RX_HANDLER_EXACT;
}
skb->dev = bond->dev;
if (bond->params.mode == BOND_MODE_ALB &&
bond->dev->priv_flags & IFF_BRIDGE_PORT &&
skb->pkt_type == PACKET_HOST) {
if (unlikely(skb_cow_head(skb,
skb->data - skb_mac_header(skb)))) {
kfree_skb(skb);
return RX_HANDLER_CONSUMED;
}
memcpy(eth_hdr(skb)->h_dest, bond->dev->dev_addr, ETH_ALEN);
}
return ret;
}
/* enslave device <slave> to bond device <master> */
int bond_enslave(struct net_device *bond_dev, struct net_device *slave_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
const struct net_device_ops *slave_ops = slave_dev->netdev_ops;
struct slave *new_slave = NULL;
struct netdev_hw_addr *ha;
struct sockaddr addr;
int link_reporting;
int res = 0;
if (!bond->params.use_carrier && slave_dev->ethtool_ops == NULL &&
slave_ops->ndo_do_ioctl == NULL) {
pr_warning("%s: Warning: no link monitoring support for %s\n",
bond_dev->name, slave_dev->name);
}
/* already enslaved */
if (slave_dev->flags & IFF_SLAVE) {
pr_debug("Error, Device was already enslaved\n");
return -EBUSY;
}
/* vlan challenged mutual exclusion */
/* no need to lock since we're protected by rtnl_lock */
if (slave_dev->features & NETIF_F_VLAN_CHALLENGED) {
pr_debug("%s: NETIF_F_VLAN_CHALLENGED\n", slave_dev->name);
if (vlan_uses_dev(bond_dev)) {
pr_err("%s: Error: cannot enslave VLAN challenged slave %s on VLAN enabled bond %s\n",
bond_dev->name, slave_dev->name, bond_dev->name);
return -EPERM;
} else {
pr_warning("%s: Warning: enslaved VLAN challenged slave %s. Adding VLANs will be blocked as long as %s is part of bond %s\n",
bond_dev->name, slave_dev->name,
slave_dev->name, bond_dev->name);
}
} else {
pr_debug("%s: ! NETIF_F_VLAN_CHALLENGED\n", slave_dev->name);
}
/*
* Old ifenslave binaries are no longer supported. These can
* be identified with moderate accuracy by the state of the slave:
* the current ifenslave will set the interface down prior to
* enslaving it; the old ifenslave will not.
*/
if ((slave_dev->flags & IFF_UP)) {
pr_err("%s is up. This may be due to an out of date ifenslave.\n",
slave_dev->name);
res = -EPERM;
goto err_undo_flags;
}
/* set bonding device ether type by slave - bonding netdevices are
* created with ether_setup, so when the slave type is not ARPHRD_ETHER
* there is a need to override some of the type dependent attribs/funcs.
*
* bond ether type mutual exclusion - don't allow slaves of dissimilar
* ether type (eg ARPHRD_ETHER and ARPHRD_INFINIBAND) share the same bond
*/
if (bond->slave_cnt == 0) {
bonding: clean muticast addresses when device changes type Bonding device forbids slave device of different types under the same master. However, it is possible for a bonding master to change type during its lifetime. This can be either from ARPHRD_ETHER to ARPHRD_INFINIBAND or the other way arround. The change of type requires device level multicast address cleanup because device level multicast addresses depend on the device type. The patch adds a call to dev_close() before the bonding master changes type and dev_open() just after that. In the example below I enslaved an IPoIB device (ib0) under bond0. Since each bonding master starts as device of type ARPHRD_ETHER by default, a change of type occurs when ib0 is enslaved. This is how /proc/net/dev_mcast looks like without the patch 5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05 5 bond0 1 0 01005e000116 5 bond0 1 0 01005e7ffffd 5 bond0 1 0 01005e000001 5 bond0 1 0 333300000001 6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05 6 ib0 1 0 333300000001 6 ib0 1 0 01005e000001 6 ib0 1 0 01005e7ffffd 6 ib0 1 0 01005e000116 6 ib0 1 0 00ffffffff12401bffff00000000000000000001 6 ib0 1 0 00ffffffff12601bffff00000000000000000001 and this is how it looks like after the patch. 5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05 5 bond0 1 0 00ffffffff12601bffff00000000000000000001 5 bond0 1 0 00ffffffff12401bffff0000000000000ffffffd 5 bond0 1 0 00ffffffff12401bffff00000000000000000116 5 bond0 1 0 00ffffffff12401bffff00000000000000000001 6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05 6 ib0 1 0 00ffffffff12401bffff00000000000000000116 6 ib0 1 0 00ffffffff12401bffff0000000000000ffffffd 6 ib0 2 0 00ffffffff12401bffff00000000000000000001 6 ib0 2 0 00ffffffff12601bffff00000000000000000001 Signed-off-by: Moni Shoua <monis@voltaire.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-15 04:56:31 +00:00
if (bond_dev->type != slave_dev->type) {
pr_debug("%s: change device type from %d to %d\n",
bond_dev->name,
bond_dev->type, slave_dev->type);
res = call_netdevice_notifiers(NETDEV_PRE_TYPE_CHANGE,
bond_dev);
res = notifier_to_errno(res);
if (res) {
pr_err("%s: refused to change device type\n",
bond_dev->name);
res = -EBUSY;
goto err_undo_flags;
}
/* Flush unicast and multicast addresses */
dev_uc_flush(bond_dev);
dev_mc_flush(bond_dev);
bonding: clean muticast addresses when device changes type Bonding device forbids slave device of different types under the same master. However, it is possible for a bonding master to change type during its lifetime. This can be either from ARPHRD_ETHER to ARPHRD_INFINIBAND or the other way arround. The change of type requires device level multicast address cleanup because device level multicast addresses depend on the device type. The patch adds a call to dev_close() before the bonding master changes type and dev_open() just after that. In the example below I enslaved an IPoIB device (ib0) under bond0. Since each bonding master starts as device of type ARPHRD_ETHER by default, a change of type occurs when ib0 is enslaved. This is how /proc/net/dev_mcast looks like without the patch 5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05 5 bond0 1 0 01005e000116 5 bond0 1 0 01005e7ffffd 5 bond0 1 0 01005e000001 5 bond0 1 0 333300000001 6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05 6 ib0 1 0 333300000001 6 ib0 1 0 01005e000001 6 ib0 1 0 01005e7ffffd 6 ib0 1 0 01005e000116 6 ib0 1 0 00ffffffff12401bffff00000000000000000001 6 ib0 1 0 00ffffffff12601bffff00000000000000000001 and this is how it looks like after the patch. 5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05 5 bond0 1 0 00ffffffff12601bffff00000000000000000001 5 bond0 1 0 00ffffffff12401bffff0000000000000ffffffd 5 bond0 1 0 00ffffffff12401bffff00000000000000000116 5 bond0 1 0 00ffffffff12401bffff00000000000000000001 6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05 6 ib0 1 0 00ffffffff12401bffff00000000000000000116 6 ib0 1 0 00ffffffff12401bffff0000000000000ffffffd 6 ib0 2 0 00ffffffff12401bffff00000000000000000001 6 ib0 2 0 00ffffffff12601bffff00000000000000000001 Signed-off-by: Moni Shoua <monis@voltaire.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-15 04:56:31 +00:00
if (slave_dev->type != ARPHRD_ETHER)
bond_setup_by_slave(bond_dev, slave_dev);
else {
bonding: clean muticast addresses when device changes type Bonding device forbids slave device of different types under the same master. However, it is possible for a bonding master to change type during its lifetime. This can be either from ARPHRD_ETHER to ARPHRD_INFINIBAND or the other way arround. The change of type requires device level multicast address cleanup because device level multicast addresses depend on the device type. The patch adds a call to dev_close() before the bonding master changes type and dev_open() just after that. In the example below I enslaved an IPoIB device (ib0) under bond0. Since each bonding master starts as device of type ARPHRD_ETHER by default, a change of type occurs when ib0 is enslaved. This is how /proc/net/dev_mcast looks like without the patch 5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05 5 bond0 1 0 01005e000116 5 bond0 1 0 01005e7ffffd 5 bond0 1 0 01005e000001 5 bond0 1 0 333300000001 6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05 6 ib0 1 0 333300000001 6 ib0 1 0 01005e000001 6 ib0 1 0 01005e7ffffd 6 ib0 1 0 01005e000116 6 ib0 1 0 00ffffffff12401bffff00000000000000000001 6 ib0 1 0 00ffffffff12601bffff00000000000000000001 and this is how it looks like after the patch. 5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05 5 bond0 1 0 00ffffffff12601bffff00000000000000000001 5 bond0 1 0 00ffffffff12401bffff0000000000000ffffffd 5 bond0 1 0 00ffffffff12401bffff00000000000000000116 5 bond0 1 0 00ffffffff12401bffff00000000000000000001 6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05 6 ib0 1 0 00ffffffff12401bffff00000000000000000116 6 ib0 1 0 00ffffffff12401bffff0000000000000ffffffd 6 ib0 2 0 00ffffffff12401bffff00000000000000000001 6 ib0 2 0 00ffffffff12601bffff00000000000000000001 Signed-off-by: Moni Shoua <monis@voltaire.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-15 04:56:31 +00:00
ether_setup(bond_dev);
bond_dev->priv_flags &= ~IFF_TX_SKB_SHARING;
}
call_netdevice_notifiers(NETDEV_POST_TYPE_CHANGE,
bond_dev);
bonding: clean muticast addresses when device changes type Bonding device forbids slave device of different types under the same master. However, it is possible for a bonding master to change type during its lifetime. This can be either from ARPHRD_ETHER to ARPHRD_INFINIBAND or the other way arround. The change of type requires device level multicast address cleanup because device level multicast addresses depend on the device type. The patch adds a call to dev_close() before the bonding master changes type and dev_open() just after that. In the example below I enslaved an IPoIB device (ib0) under bond0. Since each bonding master starts as device of type ARPHRD_ETHER by default, a change of type occurs when ib0 is enslaved. This is how /proc/net/dev_mcast looks like without the patch 5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05 5 bond0 1 0 01005e000116 5 bond0 1 0 01005e7ffffd 5 bond0 1 0 01005e000001 5 bond0 1 0 333300000001 6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05 6 ib0 1 0 333300000001 6 ib0 1 0 01005e000001 6 ib0 1 0 01005e7ffffd 6 ib0 1 0 01005e000116 6 ib0 1 0 00ffffffff12401bffff00000000000000000001 6 ib0 1 0 00ffffffff12601bffff00000000000000000001 and this is how it looks like after the patch. 5 bond0 1 0 00ffffffff12601bffff000000000001ff96ca05 5 bond0 1 0 00ffffffff12601bffff00000000000000000001 5 bond0 1 0 00ffffffff12401bffff0000000000000ffffffd 5 bond0 1 0 00ffffffff12401bffff00000000000000000116 5 bond0 1 0 00ffffffff12401bffff00000000000000000001 6 ib0 1 0 00ffffffff12601bffff000000000001ff96ca05 6 ib0 1 0 00ffffffff12401bffff00000000000000000116 6 ib0 1 0 00ffffffff12401bffff0000000000000ffffffd 6 ib0 2 0 00ffffffff12401bffff00000000000000000001 6 ib0 2 0 00ffffffff12601bffff00000000000000000001 Signed-off-by: Moni Shoua <monis@voltaire.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-15 04:56:31 +00:00
}
} else if (bond_dev->type != slave_dev->type) {
pr_err("%s ether type (%d) is different from other slaves (%d), can not enslave it.\n",
slave_dev->name,
slave_dev->type, bond_dev->type);
res = -EINVAL;
goto err_undo_flags;
}
if (slave_ops->ndo_set_mac_address == NULL) {
if (bond->slave_cnt == 0) {
pr_warning("%s: Warning: The first slave device specified does not support setting the MAC address. Setting fail_over_mac to active.",
bond_dev->name);
bond->params.fail_over_mac = BOND_FOM_ACTIVE;
} else if (bond->params.fail_over_mac != BOND_FOM_ACTIVE) {
pr_err("%s: Error: The slave device specified does not support setting the MAC address, but fail_over_mac is not set to active.\n",
bond_dev->name);
res = -EOPNOTSUPP;
goto err_undo_flags;
}
}
call_netdevice_notifiers(NETDEV_JOIN, slave_dev);
/* If this is the first slave, then we need to set the master's hardware
* address to be the same as the slave's. */
if (is_zero_ether_addr(bond->dev->dev_addr))
memcpy(bond->dev->dev_addr, slave_dev->dev_addr,
slave_dev->addr_len);
new_slave = kzalloc(sizeof(struct slave), GFP_KERNEL);
if (!new_slave) {
res = -ENOMEM;
goto err_undo_flags;
}
bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 08:40:18 +00:00
/*
* Set the new_slave's queue_id to be zero. Queue ID mapping
* is set via sysfs or module option if desired.
*/
new_slave->queue_id = 0;
/* Save slave's original mtu and then set it to match the bond */
new_slave->original_mtu = slave_dev->mtu;
res = dev_set_mtu(slave_dev, bond->dev->mtu);
if (res) {
pr_debug("Error %d calling dev_set_mtu\n", res);
goto err_free;
}
/*
* Save slave's original ("permanent") mac address for modes
* that need it, and for restoring it upon release, and then
* set it to the master's address
*/
memcpy(new_slave->perm_hwaddr, slave_dev->dev_addr, ETH_ALEN);
if (!bond->params.fail_over_mac) {
/*
* Set slave to master's mac address. The application already
* set the master's mac address to that of the first slave
*/
memcpy(addr.sa_data, bond_dev->dev_addr, bond_dev->addr_len);
addr.sa_family = slave_dev->type;
res = dev_set_mac_address(slave_dev, &addr);
if (res) {
pr_debug("Error %d calling set_mac_address\n", res);
goto err_restore_mtu;
}
}
res = netdev_set_bond_master(slave_dev, bond_dev);
if (res) {
pr_debug("Error %d calling netdev_set_bond_master\n", res);
goto err_restore_mac;
}
/* open the slave since the application closed it */
res = dev_open(slave_dev);
if (res) {
pr_debug("Opening slave %s failed\n", slave_dev->name);
goto err_unset_master;
}
new_slave->bond = bond;
new_slave->dev = slave_dev;
slave_dev->priv_flags |= IFF_BONDING;
if (bond_is_lb(bond)) {
/* bond_alb_init_slave() must be called before all other stages since
* it might fail and we do not want to have to undo everything
*/
res = bond_alb_init_slave(bond, new_slave);
if (res)
goto err_close;
}
/* If the mode USES_PRIMARY, then the new slave gets the
* master's promisc (and mc) settings only if it becomes the
* curr_active_slave, and that is taken care of later when calling
* bond_change_active()
*/
if (!USES_PRIMARY(bond->params.mode)) {
/* set promiscuity level to new slave */
if (bond_dev->flags & IFF_PROMISC) {
res = dev_set_promiscuity(slave_dev, 1);
if (res)
goto err_close;
}
/* set allmulti level to new slave */
if (bond_dev->flags & IFF_ALLMULTI) {
res = dev_set_allmulti(slave_dev, 1);
if (res)
goto err_close;
}
netif_addr_lock_bh(bond_dev);
/* upload master's mc_list to new slave */
netdev_for_each_mc_addr(ha, bond_dev)
dev_mc_add(slave_dev, ha->addr);
netif_addr_unlock_bh(bond_dev);
}
if (bond->params.mode == BOND_MODE_8023AD) {
/* add lacpdu mc addr to mc list */
u8 lacpdu_multicast[ETH_ALEN] = MULTICAST_LACPDU_ADDR;
dev_mc_add(slave_dev, lacpdu_multicast);
}
bond_add_vlans_on_slave(bond, slave_dev);
write_lock_bh(&bond->lock);
bond_attach_slave(bond, new_slave);
new_slave->delay = 0;
new_slave->link_failure_count = 0;
write_unlock_bh(&bond->lock);
bond_compute_features(bond);
read_lock(&bond->lock);
new_slave->last_arp_rx = jiffies -
(msecs_to_jiffies(bond->params.arp_interval) + 1);
if (bond->params.miimon && !bond->params.use_carrier) {
link_reporting = bond_check_dev_link(bond, slave_dev, 1);
if ((link_reporting == -1) && !bond->params.arp_interval) {
/*
* miimon is set but a bonded network driver
* does not support ETHTOOL/MII and
* arp_interval is not set. Note: if
* use_carrier is enabled, we will never go
* here (because netif_carrier is always
* supported); thus, we don't need to change
* the messages for netif_carrier.
*/
pr_warning("%s: Warning: MII and ETHTOOL support not available for interface %s, and arp_interval/arp_ip_target module parameters not specified, thus bonding will not detect link failures! see bonding.txt for details.\n",
bond_dev->name, slave_dev->name);
} else if (link_reporting == -1) {
/* unable get link status using mii/ethtool */
pr_warning("%s: Warning: can't get link status from interface %s; the network driver associated with this interface does not support MII or ETHTOOL link status reporting, thus miimon has no effect on this interface.\n",
bond_dev->name, slave_dev->name);
}
}
/* check for initial state */
if (bond->params.miimon) {
if (bond_check_dev_link(bond, slave_dev, 0) == BMSR_LSTATUS) {
if (bond->params.updelay) {
new_slave->link = BOND_LINK_BACK;
new_slave->delay = bond->params.updelay;
} else {
new_slave->link = BOND_LINK_UP;
}
} else {
new_slave->link = BOND_LINK_DOWN;
}
} else if (bond->params.arp_interval) {
new_slave->link = (netif_carrier_ok(slave_dev) ?
BOND_LINK_UP : BOND_LINK_DOWN);
} else {
new_slave->link = BOND_LINK_UP;
}
if (new_slave->link != BOND_LINK_DOWN)
new_slave->jiffies = jiffies;
pr_debug("Initial state of slave_dev is BOND_LINK_%s\n",
new_slave->link == BOND_LINK_DOWN ? "DOWN" :
(new_slave->link == BOND_LINK_UP ? "UP" : "BACK"));
bond_update_speed_duplex(new_slave);
if (USES_PRIMARY(bond->params.mode) && bond->params.primary[0]) {
/* if there is a primary slave, remember it */
if (strcmp(bond->params.primary, new_slave->dev->name) == 0) {
bond->primary_slave = new_slave;
bond->force_primary = true;
}
}
write_lock_bh(&bond->curr_slave_lock);
switch (bond->params.mode) {
case BOND_MODE_ACTIVEBACKUP:
bond_set_slave_inactive_flags(new_slave);
bond_select_active_slave(bond);
break;
case BOND_MODE_8023AD:
/* in 802.3ad mode, the internal mechanism
* will activate the slaves in the selected
* aggregator
*/
bond_set_slave_inactive_flags(new_slave);
/* if this is the first slave */
if (bond->slave_cnt == 1) {
SLAVE_AD_INFO(new_slave).id = 1;
/* Initialize AD with the number of times that the AD timer is called in 1 second
* can be called only after the mac address of the bond is set
*/
bond_3ad_initialize(bond, 1000/AD_TIMER_INTERVAL);
} else {
SLAVE_AD_INFO(new_slave).id =
SLAVE_AD_INFO(new_slave->prev).id + 1;
}
bond_3ad_bind_slave(new_slave);
break;
case BOND_MODE_TLB:
case BOND_MODE_ALB:
bond_set_active_slave(new_slave);
bond_set_slave_inactive_flags(new_slave);
bonding: select current active slave when enslaving device for mode tlb and alb I've hit an issue on my system when I've been using RealTek RTL8139D cards in bonding interface in mode balancing-alb. When I enslave a card, the current active slave (bond->curr_active_slave) is not set and the link is therefore not functional. ---- # cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008) Bonding Mode: adaptive load balancing Primary Slave: None Currently Active Slave: None MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:1f:1f:01:2f:22 ---- The thing that gets it right is when I unplug the cable and then I put it back into the NIC. Then the current active slave is set to eth1 and link is working just fine. Here is dmesg log with bonding DEBUG messages turned on: ---- ADDRCONF(NETDEV_UP): bond0: link is not ready event_dev: bond0, event: 1 IFF_MASTER event_dev: bond0, event: 8 IFF_MASTER bond_ioctl: master=bond0, cmd=35216 slave_dev=cac5d800: slave_dev->name=eth1: eth1: ! NETIF_F_VLAN_CHALLENGED event_dev: eth1, event: 8 eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1 event_dev: eth1, event: 1 event_dev: eth1, event: 8 IFF_SLAVE Initial state of slave_dev is BOND_LINK_UP bonding: bond0: enslaving eth1 as an active interface with an up link. ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready event_dev: bond0, event: 4 IFF_MASTER bond0: no IPv6 routers present <<<<cable unplug>>>> eth1: link down event_dev: eth1, event: 4 IFF_SLAVE bonding: bond0: link status definitely down for interface eth1, disabling it event_dev: bond0, event: 4 IFF_MASTER <<<<cable plug>>>> eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1 event_dev: eth1, event: 4 IFF_SLAVE bonding: bond0: link status definitely up for interface eth1. bonding: bond0: making interface eth1 the new active one. event_dev: eth1, event: 8 IFF_SLAVE event_dev: eth1, event: 8 IFF_SLAVE bonding: bond0: first active interface up! event_dev: bond0, event: 4 IFF_MASTER ---- The current active slave is set by calling bond_select_active_slave() function from bond_miimon_commit() function when the slave (eth1) link goes to state up. I also tested this on other machine with Broadcom NetXtreme II BCM5708 1000Base-T NIC and there all works fine. The thing is that this adapter is down and goes up after few seconds after it is enslaved. This patch calls bond_select_active_slave() in bond_enslave() function for modes alb and tlb and makes sure that the current active slave is set up properly even when the slave state is already up. Tested on both systems, works fine. Notice: The same problem can maybe also occrur in mode 8023AD but I'm unable to test that. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-26 00:23:38 +00:00
bond_select_active_slave(bond);
break;
default:
pr_debug("This slave is always active in trunk mode\n");
/* always active in trunk mode */
bond_set_active_slave(new_slave);
/* In trunking mode there is little meaning to curr_active_slave
* anyway (it holds no special properties of the bond device),
* so we can change it without calling change_active_interface()
*/
if (!bond->curr_active_slave && new_slave->link == BOND_LINK_UP)
bond->curr_active_slave = new_slave;
break;
} /* switch(bond_mode) */
write_unlock_bh(&bond->curr_slave_lock);
bond_set_carrier(bond);
#ifdef CONFIG_NET_POLL_CONTROLLER
slave_dev->npinfo = bond_netpoll_info(bond);
if (slave_dev->npinfo) {
if (slave_enable_netpoll(new_slave)) {
read_unlock(&bond->lock);
pr_info("Error, %s: master_dev is using netpoll, "
"but new slave device does not support netpoll.\n",
bond_dev->name);
res = -EBUSY;
goto err_detach;
}
}
#endif
read_unlock(&bond->lock);
res = bond_create_slave_symlinks(bond_dev, slave_dev);
if (res)
goto err_detach;
res = netdev_rx_handler_register(slave_dev, bond_handle_frame,
new_slave);
if (res) {
pr_debug("Error %d calling netdev_rx_handler_register\n", res);
goto err_dest_symlinks;
}
pr_info("%s: enslaving %s as a%s interface with a%s link.\n",
bond_dev->name, slave_dev->name,
bond_is_active_slave(new_slave) ? "n active" : " backup",
new_slave->link != BOND_LINK_DOWN ? "n up" : " down");
/* enslave is successful */
return 0;
/* Undo stages on error */
err_dest_symlinks:
bond_destroy_slave_symlinks(bond_dev, slave_dev);
err_detach:
write_lock_bh(&bond->lock);
bond_detach_slave(bond, new_slave);
write_unlock_bh(&bond->lock);
err_close:
dev_close(slave_dev);
err_unset_master:
netdev_set_bond_master(slave_dev, NULL);
err_restore_mac:
if (!bond->params.fail_over_mac) {
/* XXX TODO - fom follow mode needs to change master's
* MAC if this slave's MAC is in use by the bond, or at
* least print a warning.
*/
memcpy(addr.sa_data, new_slave->perm_hwaddr, ETH_ALEN);
addr.sa_family = slave_dev->type;
dev_set_mac_address(slave_dev, &addr);
}
err_restore_mtu:
dev_set_mtu(slave_dev, new_slave->original_mtu);
err_free:
kfree(new_slave);
err_undo_flags:
bond_compute_features(bond);
return res;
}
/*
* Try to release the slave device <slave> from the bond device <master>
* It is legal to access curr_active_slave without a lock because all the function
* is write-locked.
*
* The rules for slave state should be:
* for Active/Backup:
* Active stays on all backups go down
* for Bonded connections:
* The first up interface should be left on and all others downed.
*/
int bond_release(struct net_device *bond_dev, struct net_device *slave_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
struct slave *slave, *oldcurrent;
struct sockaddr addr;
netdev_features_t old_features = bond_dev->features;
/* slave is not a slave or master is not master of this slave */
if (!(slave_dev->flags & IFF_SLAVE) ||
(slave_dev->master != bond_dev)) {
pr_err("%s: Error: cannot release %s.\n",
bond_dev->name, slave_dev->name);
return -EINVAL;
}
block_netpoll_tx();
call_netdevice_notifiers(NETDEV_RELEASE, bond_dev);
write_lock_bh(&bond->lock);
slave = bond_get_slave_by_dev(bond, slave_dev);
if (!slave) {
/* not a slave of this bond */
pr_info("%s: %s not enslaved\n",
bond_dev->name, slave_dev->name);
write_unlock_bh(&bond->lock);
unblock_netpoll_tx();
return -EINVAL;
}
/* unregister rx_handler early so bond_handle_frame wouldn't be called
* for this slave anymore.
*/
netdev_rx_handler_unregister(slave_dev);
write_unlock_bh(&bond->lock);
synchronize_net();
write_lock_bh(&bond->lock);
if (!bond->params.fail_over_mac) {
if (ether_addr_equal(bond_dev->dev_addr, slave->perm_hwaddr) &&
bond->slave_cnt > 1)
pr_warning("%s: Warning: the permanent HWaddr of %s - %pM - is still in use by %s. Set the HWaddr of %s to a different address to avoid conflicts.\n",
bond_dev->name, slave_dev->name,
slave->perm_hwaddr,
bond_dev->name, slave_dev->name);
}
/* Inform AD package of unbinding of slave. */
if (bond->params.mode == BOND_MODE_8023AD) {
/* must be called before the slave is
* detached from the list
*/
bond_3ad_unbind_slave(slave);
}
pr_info("%s: releasing %s interface %s\n",
bond_dev->name,
bond_is_active_slave(slave) ? "active" : "backup",
slave_dev->name);
oldcurrent = bond->curr_active_slave;
bond->current_arp_slave = NULL;
/* release the slave from its bond */
bond_detach_slave(bond, slave);
if (bond->primary_slave == slave)
bond->primary_slave = NULL;
if (oldcurrent == slave)
bond_change_active_slave(bond, NULL);
if (bond_is_lb(bond)) {
/* Must be called only after the slave has been
* detached from the list and the curr_active_slave
* has been cleared (if our_slave == old_current),
* but before a new active slave is selected.
*/
write_unlock_bh(&bond->lock);
bond_alb_deinit_slave(bond, slave);
write_lock_bh(&bond->lock);
}
if (oldcurrent == slave) {
/*
* Note that we hold RTNL over this sequence, so there
* is no concern that another slave add/remove event
* will interfere.
*/
write_unlock_bh(&bond->lock);
read_lock(&bond->lock);
write_lock_bh(&bond->curr_slave_lock);
bond_select_active_slave(bond);
write_unlock_bh(&bond->curr_slave_lock);
read_unlock(&bond->lock);
write_lock_bh(&bond->lock);
}
if (bond->slave_cnt == 0) {
bond_set_carrier(bond);
/* if the last slave was removed, zero the mac address
* of the master so it will be set by the application
* to the mac address of the first slave
*/
memset(bond_dev->dev_addr, 0, bond_dev->addr_len);
if (bond_vlan_used(bond)) {
pr_warning("%s: Warning: clearing HW address of %s while it still has VLANs.\n",
bond_dev->name, bond_dev->name);
pr_warning("%s: When re-adding slaves, make sure the bond's HW address matches its VLANs'.\n",
bond_dev->name);
}
}
write_unlock_bh(&bond->lock);
unblock_netpoll_tx();
if (bond->slave_cnt == 0)
call_netdevice_notifiers(NETDEV_CHANGEADDR, bond->dev);
bond_compute_features(bond);
if (!(bond_dev->features & NETIF_F_VLAN_CHALLENGED) &&
(old_features & NETIF_F_VLAN_CHALLENGED))
pr_info("%s: last VLAN challenged slave %s left bond %s. VLAN blocking is removed\n",
bond_dev->name, slave_dev->name, bond_dev->name);
/* must do this from outside any spinlocks */
bond_destroy_slave_symlinks(bond_dev, slave_dev);
bond_del_vlans_from_slave(bond, slave_dev);
/* If the mode USES_PRIMARY, then we should only remove its
* promisc and mc settings if it was the curr_active_slave, but that was
* already taken care of above when we detached the slave
*/
if (!USES_PRIMARY(bond->params.mode)) {
/* unset promiscuity level from slave */
if (bond_dev->flags & IFF_PROMISC)
dev_set_promiscuity(slave_dev, -1);
/* unset allmulti level from slave */
if (bond_dev->flags & IFF_ALLMULTI)
dev_set_allmulti(slave_dev, -1);
/* flush master's mc_list from slave */
netif_addr_lock_bh(bond_dev);
bond_mc_list_flush(bond_dev, slave_dev);
netif_addr_unlock_bh(bond_dev);
}
netdev_set_bond_master(slave_dev, NULL);
slave_disable_netpoll(slave);
/* close slave before restoring its mac address */
dev_close(slave_dev);
if (bond->params.fail_over_mac != BOND_FOM_ACTIVE) {
/* restore original ("permanent") mac address */
memcpy(addr.sa_data, slave->perm_hwaddr, ETH_ALEN);
addr.sa_family = slave_dev->type;
dev_set_mac_address(slave_dev, &addr);
}
dev_set_mtu(slave_dev, slave->original_mtu);
slave_dev->priv_flags &= ~IFF_BONDING;
kfree(slave);
return 0; /* deletion OK */
}
/*
* First release a slave and then destroy the bond if no more slaves are left.
* Must be under rtnl_lock when this function is called.
*/
static int bond_release_and_destroy(struct net_device *bond_dev,
struct net_device *slave_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
int ret;
ret = bond_release(bond_dev, slave_dev);
if ((ret == 0) && (bond->slave_cnt == 0)) {
bond_dev->priv_flags |= IFF_DISABLE_NETPOLL;
pr_info("%s: destroying bond %s.\n",
bond_dev->name, bond_dev->name);
unregister_netdevice(bond_dev);
}
return ret;
}
/*
* This function releases all slaves.
*/
static int bond_release_all(struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
struct slave *slave;
struct net_device *slave_dev;
struct sockaddr addr;
write_lock_bh(&bond->lock);
netif_carrier_off(bond_dev);
if (bond->slave_cnt == 0)
goto out;
bond->current_arp_slave = NULL;
bond->primary_slave = NULL;
bond_change_active_slave(bond, NULL);
while ((slave = bond->first_slave) != NULL) {
/* Inform AD package of unbinding of slave
* before slave is detached from the list.
*/
if (bond->params.mode == BOND_MODE_8023AD)
bond_3ad_unbind_slave(slave);
slave_dev = slave->dev;
bond_detach_slave(bond, slave);
/* now that the slave is detached, unlock and perform
* all the undo steps that should not be called from
* within a lock.
*/
write_unlock_bh(&bond->lock);
/* unregister rx_handler early so bond_handle_frame wouldn't
* be called for this slave anymore.
*/
netdev_rx_handler_unregister(slave_dev);
synchronize_net();
if (bond_is_lb(bond)) {
/* must be called only after the slave
* has been detached from the list
*/
bond_alb_deinit_slave(bond, slave);
}
bond_destroy_slave_symlinks(bond_dev, slave_dev);
bond_del_vlans_from_slave(bond, slave_dev);
/* If the mode USES_PRIMARY, then we should only remove its
* promisc and mc settings if it was the curr_active_slave, but that was
* already taken care of above when we detached the slave
*/
if (!USES_PRIMARY(bond->params.mode)) {
/* unset promiscuity level from slave */
if (bond_dev->flags & IFF_PROMISC)
dev_set_promiscuity(slave_dev, -1);
/* unset allmulti level from slave */
if (bond_dev->flags & IFF_ALLMULTI)
dev_set_allmulti(slave_dev, -1);
/* flush master's mc_list from slave */
netif_addr_lock_bh(bond_dev);
bond_mc_list_flush(bond_dev, slave_dev);
netif_addr_unlock_bh(bond_dev);
}
netdev_set_bond_master(slave_dev, NULL);
slave_disable_netpoll(slave);
/* close slave before restoring its mac address */
dev_close(slave_dev);
if (!bond->params.fail_over_mac) {
/* restore original ("permanent") mac address*/
memcpy(addr.sa_data, slave->perm_hwaddr, ETH_ALEN);
addr.sa_family = slave_dev->type;
dev_set_mac_address(slave_dev, &addr);
}
kfree(slave);
/* re-acquire the lock before getting the next slave */
write_lock_bh(&bond->lock);
}
/* zero the mac address of the master so it will be
* set by the application to the mac address of the
* first slave
*/
memset(bond_dev->dev_addr, 0, bond_dev->addr_len);
if (bond_vlan_used(bond)) {
pr_warning("%s: Warning: clearing HW address of %s while it still has VLANs.\n",
bond_dev->name, bond_dev->name);
pr_warning("%s: When re-adding slaves, make sure the bond's HW address matches its VLANs'.\n",
bond_dev->name);
}
pr_info("%s: released all slaves\n", bond_dev->name);
out:
write_unlock_bh(&bond->lock);
bond_compute_features(bond);
return 0;
}
/*
* This function changes the active slave to slave <slave_dev>.
* It returns -EINVAL in the following cases.
* - <slave_dev> is not found in the list.
* - There is not active slave now.
* - <slave_dev> is already active.
* - The link state of <slave_dev> is not BOND_LINK_UP.
* - <slave_dev> is not running.
* In these cases, this function does nothing.
* In the other cases, current_slave pointer is changed and 0 is returned.
*/
static int bond_ioctl_change_active(struct net_device *bond_dev, struct net_device *slave_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
struct slave *old_active = NULL;
struct slave *new_active = NULL;
int res = 0;
if (!USES_PRIMARY(bond->params.mode))
return -EINVAL;
/* Verify that master_dev is indeed the master of slave_dev */
if (!(slave_dev->flags & IFF_SLAVE) || (slave_dev->master != bond_dev))
return -EINVAL;
read_lock(&bond->lock);
read_lock(&bond->curr_slave_lock);
old_active = bond->curr_active_slave;
read_unlock(&bond->curr_slave_lock);
new_active = bond_get_slave_by_dev(bond, slave_dev);
/*
* Changing to the current active: do nothing; return success.
*/
if (new_active && (new_active == old_active)) {
read_unlock(&bond->lock);
return 0;
}
if ((new_active) &&
(old_active) &&
(new_active->link == BOND_LINK_UP) &&
IS_UP(new_active->dev)) {
block_netpoll_tx();
write_lock_bh(&bond->curr_slave_lock);
bond_change_active_slave(bond, new_active);
write_unlock_bh(&bond->curr_slave_lock);
unblock_netpoll_tx();
} else
res = -EINVAL;
read_unlock(&bond->lock);
return res;
}
static int bond_info_query(struct net_device *bond_dev, struct ifbond *info)
{
struct bonding *bond = netdev_priv(bond_dev);
info->bond_mode = bond->params.mode;
info->miimon = bond->params.miimon;
read_lock(&bond->lock);
info->num_slaves = bond->slave_cnt;
read_unlock(&bond->lock);
return 0;
}
static int bond_slave_info_query(struct net_device *bond_dev, struct ifslave *info)
{
struct bonding *bond = netdev_priv(bond_dev);
struct slave *slave;
int i, res = -ENODEV;
read_lock(&bond->lock);
bond_for_each_slave(bond, slave, i) {
if (i == (int)info->slave_id) {
res = 0;
strcpy(info->slave_name, slave->dev->name);
info->link = slave->link;
info->state = bond_slave_state(slave);
info->link_failure_count = slave->link_failure_count;
break;
}
}
read_unlock(&bond->lock);
return res;
}
/*-------------------------------- Monitoring -------------------------------*/
static int bond_miimon_inspect(struct bonding *bond)
{
struct slave *slave;
int i, link_state, commit = 0;
bool ignore_updelay;
ignore_updelay = !bond->curr_active_slave ? true : false;
bond_for_each_slave(bond, slave, i) {
slave->new_link = BOND_LINK_NOCHANGE;
link_state = bond_check_dev_link(bond, slave->dev, 0);
switch (slave->link) {
case BOND_LINK_UP:
if (link_state)
continue;
slave->link = BOND_LINK_FAIL;
slave->delay = bond->params.downdelay;
if (slave->delay) {
pr_info("%s: link status down for %sinterface %s, disabling it in %d ms.\n",
bond->dev->name,
(bond->params.mode ==
BOND_MODE_ACTIVEBACKUP) ?
(bond_is_active_slave(slave) ?
"active " : "backup ") : "",
slave->dev->name,
bond->params.downdelay * bond->params.miimon);
}
/*FALLTHRU*/
case BOND_LINK_FAIL:
if (link_state) {
/*
* recovered before downdelay expired
*/
slave->link = BOND_LINK_UP;
slave->jiffies = jiffies;
pr_info("%s: link status up again after %d ms for interface %s.\n",
bond->dev->name,
(bond->params.downdelay - slave->delay) *
bond->params.miimon,
slave->dev->name);
continue;
}
if (slave->delay <= 0) {
slave->new_link = BOND_LINK_DOWN;
commit++;
continue;
}
slave->delay--;
break;
case BOND_LINK_DOWN:
if (!link_state)
continue;
slave->link = BOND_LINK_BACK;
slave->delay = bond->params.updelay;
if (slave->delay) {
pr_info("%s: link status up for interface %s, enabling it in %d ms.\n",
bond->dev->name, slave->dev->name,
ignore_updelay ? 0 :
bond->params.updelay *
bond->params.miimon);
}
/*FALLTHRU*/
case BOND_LINK_BACK:
if (!link_state) {
slave->link = BOND_LINK_DOWN;
pr_info("%s: link status down again after %d ms for interface %s.\n",
bond->dev->name,
(bond->params.updelay - slave->delay) *
bond->params.miimon,
slave->dev->name);
continue;
}
if (ignore_updelay)
slave->delay = 0;
if (slave->delay <= 0) {
slave->new_link = BOND_LINK_UP;
commit++;
ignore_updelay = false;
continue;
}
slave->delay--;
break;
}
}
return commit;
}
static void bond_miimon_commit(struct bonding *bond)
{
struct slave *slave;
int i;
bond_for_each_slave(bond, slave, i) {
switch (slave->new_link) {
case BOND_LINK_NOCHANGE:
continue;
case BOND_LINK_UP:
slave->link = BOND_LINK_UP;
slave->jiffies = jiffies;
if (bond->params.mode == BOND_MODE_8023AD) {
/* prevent it from being the active one */
bond_set_backup_slave(slave);
} else if (bond->params.mode != BOND_MODE_ACTIVEBACKUP) {
/* make it immediately active */
bond_set_active_slave(slave);
} else if (slave != bond->primary_slave) {
/* prevent it from being the active one */
bond_set_backup_slave(slave);
}
bond_update_speed_duplex(slave);
pr_info("%s: link status definitely up for interface %s, %u Mbps %s duplex.\n",
bond->dev->name, slave->dev->name,
slave->speed, slave->duplex ? "full" : "half");
/* notify ad that the link status has changed */
if (bond->params.mode == BOND_MODE_8023AD)
bond_3ad_handle_link_change(slave, BOND_LINK_UP);
if (bond_is_lb(bond))
bond_alb_handle_link_change(bond, slave,
BOND_LINK_UP);
if (!bond->curr_active_slave ||
(slave == bond->primary_slave))
goto do_failover;
continue;
case BOND_LINK_DOWN:
if (slave->link_failure_count < UINT_MAX)
slave->link_failure_count++;
slave->link = BOND_LINK_DOWN;
if (bond->params.mode == BOND_MODE_ACTIVEBACKUP ||
bond->params.mode == BOND_MODE_8023AD)
bond_set_slave_inactive_flags(slave);
pr_info("%s: link status definitely down for interface %s, disabling it\n",
bond->dev->name, slave->dev->name);
if (bond->params.mode == BOND_MODE_8023AD)
bond_3ad_handle_link_change(slave,
BOND_LINK_DOWN);
if (bond_is_lb(bond))
bond_alb_handle_link_change(bond, slave,
BOND_LINK_DOWN);
if (slave == bond->curr_active_slave)
goto do_failover;
continue;
default:
pr_err("%s: invalid new link %d on slave %s\n",
bond->dev->name, slave->new_link,
slave->dev->name);
slave->new_link = BOND_LINK_NOCHANGE;
continue;
}
do_failover:
ASSERT_RTNL();
block_netpoll_tx();
write_lock_bh(&bond->curr_slave_lock);
bond_select_active_slave(bond);
write_unlock_bh(&bond->curr_slave_lock);
unblock_netpoll_tx();
}
bond_set_carrier(bond);
}
/*
* bond_mii_monitor
*
* Really a wrapper that splits the mii monitor into two phases: an
* inspection, then (if inspection indicates something needs to be done)
* an acquisition of appropriate locks followed by a commit phase to
* implement whatever link state changes are indicated.
*/
void bond_mii_monitor(struct work_struct *work)
{
struct bonding *bond = container_of(work, struct bonding,
mii_work.work);
bool should_notify_peers = false;
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
unsigned long delay;
read_lock(&bond->lock);
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
delay = msecs_to_jiffies(bond->params.miimon);
if (bond->slave_cnt == 0)
goto re_arm;
should_notify_peers = bond_should_notify_peers(bond);
if (bond_miimon_inspect(bond)) {
read_unlock(&bond->lock);
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
/* Race avoidance with bond_close cancel of workqueue */
if (!rtnl_trylock()) {
read_lock(&bond->lock);
delay = 1;
should_notify_peers = false;
goto re_arm;
}
read_lock(&bond->lock);
bond_miimon_commit(bond);
read_unlock(&bond->lock);
rtnl_unlock(); /* might sleep, hold no other locks */
read_lock(&bond->lock);
}
re_arm:
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
if (bond->params.miimon)
queue_delayed_work(bond->wq, &bond->mii_work, delay);
read_unlock(&bond->lock);
if (should_notify_peers) {
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
if (!rtnl_trylock()) {
read_lock(&bond->lock);
bond->send_peer_notif++;
read_unlock(&bond->lock);
return;
}
call_netdevice_notifiers(NETDEV_NOTIFY_PEERS, bond->dev);
rtnl_unlock();
}
}
static int bond_has_this_ip(struct bonding *bond, __be32 ip)
{
struct vlan_entry *vlan;
bonding: remove entries for master_ip and vlan_ip and query devices instead The following patch aimed to resolve an issue where secondary, tertiary, etc. addresses added to bond interfaces could overwrite the bond->master_ip and vlan_ip values. commit 917fbdb32f37e9a93b00bb12ee83532982982df3 Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Date: Wed Nov 23 23:37:15 2011 +0000 bonding: only use primary address for ARP That patch was good because it prevented bonds using ARP monitoring from sending frames with an invalid source IP address. Unfortunately, it didn't always work as expected. When using an ioctl (like ifconfig does) to set the IP address and netmask, 2 separate ioctls are actually called to set the IP and netmask if the mask chosen doesn't match the standard mask for that class of address. The first ioctl did not have a mask that matched the one in the primary address and would still cause the device address to be overwritten. The second ioctl that was called to set the mask would then detect as secondary and ignored, but the damage was already done. This was not an issue when using an application that used netlink sockets as the setting of IP and netmask came down at once. The inconsistent behavior between those two interfaces was something that needed to be resolved. While I was thinking about how I wanted to resolve this, Ralf Zeidler came with a patch that resolved this on a RHEL kernel by keeping a full shadow of the entries in dev->ifa_list for the bonding device and vlan devices in the bonding driver. I didn't like the duplication of the list as I want to see the 'bonding' struct and code shrink rather than grow, but liked the general idea. As the Subject indicates this patch drops the master_ip and vlan_ip elements from the 'bonding' and 'vlan_entry' structs, respectively. This can be done because a device's address-list is now traversed to determine the optimal source IP address for ARP requests and for checks to see if the bonding device has a particular IP address. This code could have all be contained inside the bonding driver, but it made more sense to me to EXPORT and call inet_confirm_addr since it did exactly what was needed. I tested this and a backported patch and everything works as expected. Ralf also helped with verification of the backported patch. Thanks to Ralf for all his help on this. v2: Whitespace and organizational changes based on suggestions from Jay Vosburgh and Dave Miller. v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's suggestion. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Ralf Zeidler <ralf.zeidler@nsn.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 16:14:29 +00:00
struct net_device *vlan_dev;
bonding: remove entries for master_ip and vlan_ip and query devices instead The following patch aimed to resolve an issue where secondary, tertiary, etc. addresses added to bond interfaces could overwrite the bond->master_ip and vlan_ip values. commit 917fbdb32f37e9a93b00bb12ee83532982982df3 Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Date: Wed Nov 23 23:37:15 2011 +0000 bonding: only use primary address for ARP That patch was good because it prevented bonds using ARP monitoring from sending frames with an invalid source IP address. Unfortunately, it didn't always work as expected. When using an ioctl (like ifconfig does) to set the IP address and netmask, 2 separate ioctls are actually called to set the IP and netmask if the mask chosen doesn't match the standard mask for that class of address. The first ioctl did not have a mask that matched the one in the primary address and would still cause the device address to be overwritten. The second ioctl that was called to set the mask would then detect as secondary and ignored, but the damage was already done. This was not an issue when using an application that used netlink sockets as the setting of IP and netmask came down at once. The inconsistent behavior between those two interfaces was something that needed to be resolved. While I was thinking about how I wanted to resolve this, Ralf Zeidler came with a patch that resolved this on a RHEL kernel by keeping a full shadow of the entries in dev->ifa_list for the bonding device and vlan devices in the bonding driver. I didn't like the duplication of the list as I want to see the 'bonding' struct and code shrink rather than grow, but liked the general idea. As the Subject indicates this patch drops the master_ip and vlan_ip elements from the 'bonding' and 'vlan_entry' structs, respectively. This can be done because a device's address-list is now traversed to determine the optimal source IP address for ARP requests and for checks to see if the bonding device has a particular IP address. This code could have all be contained inside the bonding driver, but it made more sense to me to EXPORT and call inet_confirm_addr since it did exactly what was needed. I tested this and a backported patch and everything works as expected. Ralf also helped with verification of the backported patch. Thanks to Ralf for all his help on this. v2: Whitespace and organizational changes based on suggestions from Jay Vosburgh and Dave Miller. v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's suggestion. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Ralf Zeidler <ralf.zeidler@nsn.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 16:14:29 +00:00
if (ip == bond_confirm_addr(bond->dev, 0, ip))
return 1;
list_for_each_entry(vlan, &bond->vlan_list, vlan_list) {
bonding: remove entries for master_ip and vlan_ip and query devices instead The following patch aimed to resolve an issue where secondary, tertiary, etc. addresses added to bond interfaces could overwrite the bond->master_ip and vlan_ip values. commit 917fbdb32f37e9a93b00bb12ee83532982982df3 Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Date: Wed Nov 23 23:37:15 2011 +0000 bonding: only use primary address for ARP That patch was good because it prevented bonds using ARP monitoring from sending frames with an invalid source IP address. Unfortunately, it didn't always work as expected. When using an ioctl (like ifconfig does) to set the IP address and netmask, 2 separate ioctls are actually called to set the IP and netmask if the mask chosen doesn't match the standard mask for that class of address. The first ioctl did not have a mask that matched the one in the primary address and would still cause the device address to be overwritten. The second ioctl that was called to set the mask would then detect as secondary and ignored, but the damage was already done. This was not an issue when using an application that used netlink sockets as the setting of IP and netmask came down at once. The inconsistent behavior between those two interfaces was something that needed to be resolved. While I was thinking about how I wanted to resolve this, Ralf Zeidler came with a patch that resolved this on a RHEL kernel by keeping a full shadow of the entries in dev->ifa_list for the bonding device and vlan devices in the bonding driver. I didn't like the duplication of the list as I want to see the 'bonding' struct and code shrink rather than grow, but liked the general idea. As the Subject indicates this patch drops the master_ip and vlan_ip elements from the 'bonding' and 'vlan_entry' structs, respectively. This can be done because a device's address-list is now traversed to determine the optimal source IP address for ARP requests and for checks to see if the bonding device has a particular IP address. This code could have all be contained inside the bonding driver, but it made more sense to me to EXPORT and call inet_confirm_addr since it did exactly what was needed. I tested this and a backported patch and everything works as expected. Ralf also helped with verification of the backported patch. Thanks to Ralf for all his help on this. v2: Whitespace and organizational changes based on suggestions from Jay Vosburgh and Dave Miller. v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's suggestion. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Ralf Zeidler <ralf.zeidler@nsn.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 16:14:29 +00:00
rcu_read_lock();
vlan_dev = __vlan_find_dev_deep(bond->dev, vlan->vlan_id);
rcu_read_unlock();
if (vlan_dev && ip == bond_confirm_addr(vlan_dev, 0, ip))
return 1;
}
return 0;
}
/*
* We go to the (large) trouble of VLAN tagging ARP frames because
* switches in VLAN mode (especially if ports are configured as
* "native" to a VLAN) might not pass non-tagged frames.
*/
static void bond_arp_send(struct net_device *slave_dev, int arp_op, __be32 dest_ip, __be32 src_ip, unsigned short vlan_id)
{
struct sk_buff *skb;
pr_debug("arp %d on slave %s: dst %x src %x vid %d\n", arp_op,
slave_dev->name, dest_ip, src_ip, vlan_id);
skb = arp_create(arp_op, ETH_P_ARP, dest_ip, slave_dev, src_ip,
NULL, slave_dev->dev_addr, NULL);
if (!skb) {
pr_err("ARP packet allocation failed\n");
return;
}
if (vlan_id) {
skb = vlan_put_tag(skb, vlan_id);
if (!skb) {
pr_err("failed to insert VLAN tag\n");
return;
}
}
arp_xmit(skb);
}
static void bond_arp_send_all(struct bonding *bond, struct slave *slave)
{
int i, vlan_id;
__be32 *targets = bond->params.arp_targets;
struct vlan_entry *vlan;
bonding: remove entries for master_ip and vlan_ip and query devices instead The following patch aimed to resolve an issue where secondary, tertiary, etc. addresses added to bond interfaces could overwrite the bond->master_ip and vlan_ip values. commit 917fbdb32f37e9a93b00bb12ee83532982982df3 Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Date: Wed Nov 23 23:37:15 2011 +0000 bonding: only use primary address for ARP That patch was good because it prevented bonds using ARP monitoring from sending frames with an invalid source IP address. Unfortunately, it didn't always work as expected. When using an ioctl (like ifconfig does) to set the IP address and netmask, 2 separate ioctls are actually called to set the IP and netmask if the mask chosen doesn't match the standard mask for that class of address. The first ioctl did not have a mask that matched the one in the primary address and would still cause the device address to be overwritten. The second ioctl that was called to set the mask would then detect as secondary and ignored, but the damage was already done. This was not an issue when using an application that used netlink sockets as the setting of IP and netmask came down at once. The inconsistent behavior between those two interfaces was something that needed to be resolved. While I was thinking about how I wanted to resolve this, Ralf Zeidler came with a patch that resolved this on a RHEL kernel by keeping a full shadow of the entries in dev->ifa_list for the bonding device and vlan devices in the bonding driver. I didn't like the duplication of the list as I want to see the 'bonding' struct and code shrink rather than grow, but liked the general idea. As the Subject indicates this patch drops the master_ip and vlan_ip elements from the 'bonding' and 'vlan_entry' structs, respectively. This can be done because a device's address-list is now traversed to determine the optimal source IP address for ARP requests and for checks to see if the bonding device has a particular IP address. This code could have all be contained inside the bonding driver, but it made more sense to me to EXPORT and call inet_confirm_addr since it did exactly what was needed. I tested this and a backported patch and everything works as expected. Ralf also helped with verification of the backported patch. Thanks to Ralf for all his help on this. v2: Whitespace and organizational changes based on suggestions from Jay Vosburgh and Dave Miller. v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's suggestion. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Ralf Zeidler <ralf.zeidler@nsn.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 16:14:29 +00:00
struct net_device *vlan_dev = NULL;
struct rtable *rt;
for (i = 0; (i < BOND_MAX_ARP_TARGETS); i++) {
bonding: remove entries for master_ip and vlan_ip and query devices instead The following patch aimed to resolve an issue where secondary, tertiary, etc. addresses added to bond interfaces could overwrite the bond->master_ip and vlan_ip values. commit 917fbdb32f37e9a93b00bb12ee83532982982df3 Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Date: Wed Nov 23 23:37:15 2011 +0000 bonding: only use primary address for ARP That patch was good because it prevented bonds using ARP monitoring from sending frames with an invalid source IP address. Unfortunately, it didn't always work as expected. When using an ioctl (like ifconfig does) to set the IP address and netmask, 2 separate ioctls are actually called to set the IP and netmask if the mask chosen doesn't match the standard mask for that class of address. The first ioctl did not have a mask that matched the one in the primary address and would still cause the device address to be overwritten. The second ioctl that was called to set the mask would then detect as secondary and ignored, but the damage was already done. This was not an issue when using an application that used netlink sockets as the setting of IP and netmask came down at once. The inconsistent behavior between those two interfaces was something that needed to be resolved. While I was thinking about how I wanted to resolve this, Ralf Zeidler came with a patch that resolved this on a RHEL kernel by keeping a full shadow of the entries in dev->ifa_list for the bonding device and vlan devices in the bonding driver. I didn't like the duplication of the list as I want to see the 'bonding' struct and code shrink rather than grow, but liked the general idea. As the Subject indicates this patch drops the master_ip and vlan_ip elements from the 'bonding' and 'vlan_entry' structs, respectively. This can be done because a device's address-list is now traversed to determine the optimal source IP address for ARP requests and for checks to see if the bonding device has a particular IP address. This code could have all be contained inside the bonding driver, but it made more sense to me to EXPORT and call inet_confirm_addr since it did exactly what was needed. I tested this and a backported patch and everything works as expected. Ralf also helped with verification of the backported patch. Thanks to Ralf for all his help on this. v2: Whitespace and organizational changes based on suggestions from Jay Vosburgh and Dave Miller. v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's suggestion. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Ralf Zeidler <ralf.zeidler@nsn.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 16:14:29 +00:00
__be32 addr;
if (!targets[i])
break;
pr_debug("basa: target %x\n", targets[i]);
if (!bond_vlan_used(bond)) {
pr_debug("basa: empty vlan: arp_send\n");
bonding: remove entries for master_ip and vlan_ip and query devices instead The following patch aimed to resolve an issue where secondary, tertiary, etc. addresses added to bond interfaces could overwrite the bond->master_ip and vlan_ip values. commit 917fbdb32f37e9a93b00bb12ee83532982982df3 Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Date: Wed Nov 23 23:37:15 2011 +0000 bonding: only use primary address for ARP That patch was good because it prevented bonds using ARP monitoring from sending frames with an invalid source IP address. Unfortunately, it didn't always work as expected. When using an ioctl (like ifconfig does) to set the IP address and netmask, 2 separate ioctls are actually called to set the IP and netmask if the mask chosen doesn't match the standard mask for that class of address. The first ioctl did not have a mask that matched the one in the primary address and would still cause the device address to be overwritten. The second ioctl that was called to set the mask would then detect as secondary and ignored, but the damage was already done. This was not an issue when using an application that used netlink sockets as the setting of IP and netmask came down at once. The inconsistent behavior between those two interfaces was something that needed to be resolved. While I was thinking about how I wanted to resolve this, Ralf Zeidler came with a patch that resolved this on a RHEL kernel by keeping a full shadow of the entries in dev->ifa_list for the bonding device and vlan devices in the bonding driver. I didn't like the duplication of the list as I want to see the 'bonding' struct and code shrink rather than grow, but liked the general idea. As the Subject indicates this patch drops the master_ip and vlan_ip elements from the 'bonding' and 'vlan_entry' structs, respectively. This can be done because a device's address-list is now traversed to determine the optimal source IP address for ARP requests and for checks to see if the bonding device has a particular IP address. This code could have all be contained inside the bonding driver, but it made more sense to me to EXPORT and call inet_confirm_addr since it did exactly what was needed. I tested this and a backported patch and everything works as expected. Ralf also helped with verification of the backported patch. Thanks to Ralf for all his help on this. v2: Whitespace and organizational changes based on suggestions from Jay Vosburgh and Dave Miller. v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's suggestion. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Ralf Zeidler <ralf.zeidler@nsn.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 16:14:29 +00:00
addr = bond_confirm_addr(bond->dev, targets[i], 0);
bond_arp_send(slave->dev, ARPOP_REQUEST, targets[i],
bonding: remove entries for master_ip and vlan_ip and query devices instead The following patch aimed to resolve an issue where secondary, tertiary, etc. addresses added to bond interfaces could overwrite the bond->master_ip and vlan_ip values. commit 917fbdb32f37e9a93b00bb12ee83532982982df3 Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Date: Wed Nov 23 23:37:15 2011 +0000 bonding: only use primary address for ARP That patch was good because it prevented bonds using ARP monitoring from sending frames with an invalid source IP address. Unfortunately, it didn't always work as expected. When using an ioctl (like ifconfig does) to set the IP address and netmask, 2 separate ioctls are actually called to set the IP and netmask if the mask chosen doesn't match the standard mask for that class of address. The first ioctl did not have a mask that matched the one in the primary address and would still cause the device address to be overwritten. The second ioctl that was called to set the mask would then detect as secondary and ignored, but the damage was already done. This was not an issue when using an application that used netlink sockets as the setting of IP and netmask came down at once. The inconsistent behavior between those two interfaces was something that needed to be resolved. While I was thinking about how I wanted to resolve this, Ralf Zeidler came with a patch that resolved this on a RHEL kernel by keeping a full shadow of the entries in dev->ifa_list for the bonding device and vlan devices in the bonding driver. I didn't like the duplication of the list as I want to see the 'bonding' struct and code shrink rather than grow, but liked the general idea. As the Subject indicates this patch drops the master_ip and vlan_ip elements from the 'bonding' and 'vlan_entry' structs, respectively. This can be done because a device's address-list is now traversed to determine the optimal source IP address for ARP requests and for checks to see if the bonding device has a particular IP address. This code could have all be contained inside the bonding driver, but it made more sense to me to EXPORT and call inet_confirm_addr since it did exactly what was needed. I tested this and a backported patch and everything works as expected. Ralf also helped with verification of the backported patch. Thanks to Ralf for all his help on this. v2: Whitespace and organizational changes based on suggestions from Jay Vosburgh and Dave Miller. v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's suggestion. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Ralf Zeidler <ralf.zeidler@nsn.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 16:14:29 +00:00
addr, 0);
continue;
}
/*
* If VLANs are configured, we do a route lookup to
* determine which VLAN interface would be used, so we
* can tag the ARP with the proper VLAN tag.
*/
rt = ip_route_output(dev_net(bond->dev), targets[i], 0,
RTO_ONLINK, 0);
if (IS_ERR(rt)) {
if (net_ratelimit()) {
pr_warning("%s: no route to arp_ip_target %pI4\n",
bond->dev->name, &targets[i]);
}
continue;
}
/*
* This target is not on a VLAN
*/
if (rt->dst.dev == bond->dev) {
ip_rt_put(rt);
pr_debug("basa: rtdev == bond->dev: arp_send\n");
bonding: remove entries for master_ip and vlan_ip and query devices instead The following patch aimed to resolve an issue where secondary, tertiary, etc. addresses added to bond interfaces could overwrite the bond->master_ip and vlan_ip values. commit 917fbdb32f37e9a93b00bb12ee83532982982df3 Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Date: Wed Nov 23 23:37:15 2011 +0000 bonding: only use primary address for ARP That patch was good because it prevented bonds using ARP monitoring from sending frames with an invalid source IP address. Unfortunately, it didn't always work as expected. When using an ioctl (like ifconfig does) to set the IP address and netmask, 2 separate ioctls are actually called to set the IP and netmask if the mask chosen doesn't match the standard mask for that class of address. The first ioctl did not have a mask that matched the one in the primary address and would still cause the device address to be overwritten. The second ioctl that was called to set the mask would then detect as secondary and ignored, but the damage was already done. This was not an issue when using an application that used netlink sockets as the setting of IP and netmask came down at once. The inconsistent behavior between those two interfaces was something that needed to be resolved. While I was thinking about how I wanted to resolve this, Ralf Zeidler came with a patch that resolved this on a RHEL kernel by keeping a full shadow of the entries in dev->ifa_list for the bonding device and vlan devices in the bonding driver. I didn't like the duplication of the list as I want to see the 'bonding' struct and code shrink rather than grow, but liked the general idea. As the Subject indicates this patch drops the master_ip and vlan_ip elements from the 'bonding' and 'vlan_entry' structs, respectively. This can be done because a device's address-list is now traversed to determine the optimal source IP address for ARP requests and for checks to see if the bonding device has a particular IP address. This code could have all be contained inside the bonding driver, but it made more sense to me to EXPORT and call inet_confirm_addr since it did exactly what was needed. I tested this and a backported patch and everything works as expected. Ralf also helped with verification of the backported patch. Thanks to Ralf for all his help on this. v2: Whitespace and organizational changes based on suggestions from Jay Vosburgh and Dave Miller. v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's suggestion. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Ralf Zeidler <ralf.zeidler@nsn.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 16:14:29 +00:00
addr = bond_confirm_addr(bond->dev, targets[i], 0);
bond_arp_send(slave->dev, ARPOP_REQUEST, targets[i],
bonding: remove entries for master_ip and vlan_ip and query devices instead The following patch aimed to resolve an issue where secondary, tertiary, etc. addresses added to bond interfaces could overwrite the bond->master_ip and vlan_ip values. commit 917fbdb32f37e9a93b00bb12ee83532982982df3 Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Date: Wed Nov 23 23:37:15 2011 +0000 bonding: only use primary address for ARP That patch was good because it prevented bonds using ARP monitoring from sending frames with an invalid source IP address. Unfortunately, it didn't always work as expected. When using an ioctl (like ifconfig does) to set the IP address and netmask, 2 separate ioctls are actually called to set the IP and netmask if the mask chosen doesn't match the standard mask for that class of address. The first ioctl did not have a mask that matched the one in the primary address and would still cause the device address to be overwritten. The second ioctl that was called to set the mask would then detect as secondary and ignored, but the damage was already done. This was not an issue when using an application that used netlink sockets as the setting of IP and netmask came down at once. The inconsistent behavior between those two interfaces was something that needed to be resolved. While I was thinking about how I wanted to resolve this, Ralf Zeidler came with a patch that resolved this on a RHEL kernel by keeping a full shadow of the entries in dev->ifa_list for the bonding device and vlan devices in the bonding driver. I didn't like the duplication of the list as I want to see the 'bonding' struct and code shrink rather than grow, but liked the general idea. As the Subject indicates this patch drops the master_ip and vlan_ip elements from the 'bonding' and 'vlan_entry' structs, respectively. This can be done because a device's address-list is now traversed to determine the optimal source IP address for ARP requests and for checks to see if the bonding device has a particular IP address. This code could have all be contained inside the bonding driver, but it made more sense to me to EXPORT and call inet_confirm_addr since it did exactly what was needed. I tested this and a backported patch and everything works as expected. Ralf also helped with verification of the backported patch. Thanks to Ralf for all his help on this. v2: Whitespace and organizational changes based on suggestions from Jay Vosburgh and Dave Miller. v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's suggestion. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Ralf Zeidler <ralf.zeidler@nsn.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 16:14:29 +00:00
addr, 0);
continue;
}
vlan_id = 0;
list_for_each_entry(vlan, &bond->vlan_list, vlan_list) {
rcu_read_lock();
vlan_dev = __vlan_find_dev_deep(bond->dev,
vlan->vlan_id);
rcu_read_unlock();
if (vlan_dev == rt->dst.dev) {
vlan_id = vlan->vlan_id;
pr_debug("basa: vlan match on %s %d\n",
vlan_dev->name, vlan_id);
break;
}
}
bonding: remove entries for master_ip and vlan_ip and query devices instead The following patch aimed to resolve an issue where secondary, tertiary, etc. addresses added to bond interfaces could overwrite the bond->master_ip and vlan_ip values. commit 917fbdb32f37e9a93b00bb12ee83532982982df3 Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Date: Wed Nov 23 23:37:15 2011 +0000 bonding: only use primary address for ARP That patch was good because it prevented bonds using ARP monitoring from sending frames with an invalid source IP address. Unfortunately, it didn't always work as expected. When using an ioctl (like ifconfig does) to set the IP address and netmask, 2 separate ioctls are actually called to set the IP and netmask if the mask chosen doesn't match the standard mask for that class of address. The first ioctl did not have a mask that matched the one in the primary address and would still cause the device address to be overwritten. The second ioctl that was called to set the mask would then detect as secondary and ignored, but the damage was already done. This was not an issue when using an application that used netlink sockets as the setting of IP and netmask came down at once. The inconsistent behavior between those two interfaces was something that needed to be resolved. While I was thinking about how I wanted to resolve this, Ralf Zeidler came with a patch that resolved this on a RHEL kernel by keeping a full shadow of the entries in dev->ifa_list for the bonding device and vlan devices in the bonding driver. I didn't like the duplication of the list as I want to see the 'bonding' struct and code shrink rather than grow, but liked the general idea. As the Subject indicates this patch drops the master_ip and vlan_ip elements from the 'bonding' and 'vlan_entry' structs, respectively. This can be done because a device's address-list is now traversed to determine the optimal source IP address for ARP requests and for checks to see if the bonding device has a particular IP address. This code could have all be contained inside the bonding driver, but it made more sense to me to EXPORT and call inet_confirm_addr since it did exactly what was needed. I tested this and a backported patch and everything works as expected. Ralf also helped with verification of the backported patch. Thanks to Ralf for all his help on this. v2: Whitespace and organizational changes based on suggestions from Jay Vosburgh and Dave Miller. v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's suggestion. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Ralf Zeidler <ralf.zeidler@nsn.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 16:14:29 +00:00
if (vlan_id && vlan_dev) {
ip_rt_put(rt);
bonding: remove entries for master_ip and vlan_ip and query devices instead The following patch aimed to resolve an issue where secondary, tertiary, etc. addresses added to bond interfaces could overwrite the bond->master_ip and vlan_ip values. commit 917fbdb32f37e9a93b00bb12ee83532982982df3 Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Date: Wed Nov 23 23:37:15 2011 +0000 bonding: only use primary address for ARP That patch was good because it prevented bonds using ARP monitoring from sending frames with an invalid source IP address. Unfortunately, it didn't always work as expected. When using an ioctl (like ifconfig does) to set the IP address and netmask, 2 separate ioctls are actually called to set the IP and netmask if the mask chosen doesn't match the standard mask for that class of address. The first ioctl did not have a mask that matched the one in the primary address and would still cause the device address to be overwritten. The second ioctl that was called to set the mask would then detect as secondary and ignored, but the damage was already done. This was not an issue when using an application that used netlink sockets as the setting of IP and netmask came down at once. The inconsistent behavior between those two interfaces was something that needed to be resolved. While I was thinking about how I wanted to resolve this, Ralf Zeidler came with a patch that resolved this on a RHEL kernel by keeping a full shadow of the entries in dev->ifa_list for the bonding device and vlan devices in the bonding driver. I didn't like the duplication of the list as I want to see the 'bonding' struct and code shrink rather than grow, but liked the general idea. As the Subject indicates this patch drops the master_ip and vlan_ip elements from the 'bonding' and 'vlan_entry' structs, respectively. This can be done because a device's address-list is now traversed to determine the optimal source IP address for ARP requests and for checks to see if the bonding device has a particular IP address. This code could have all be contained inside the bonding driver, but it made more sense to me to EXPORT and call inet_confirm_addr since it did exactly what was needed. I tested this and a backported patch and everything works as expected. Ralf also helped with verification of the backported patch. Thanks to Ralf for all his help on this. v2: Whitespace and organizational changes based on suggestions from Jay Vosburgh and Dave Miller. v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's suggestion. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Ralf Zeidler <ralf.zeidler@nsn.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 16:14:29 +00:00
addr = bond_confirm_addr(vlan_dev, targets[i], 0);
bond_arp_send(slave->dev, ARPOP_REQUEST, targets[i],
bonding: remove entries for master_ip and vlan_ip and query devices instead The following patch aimed to resolve an issue where secondary, tertiary, etc. addresses added to bond interfaces could overwrite the bond->master_ip and vlan_ip values. commit 917fbdb32f37e9a93b00bb12ee83532982982df3 Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Date: Wed Nov 23 23:37:15 2011 +0000 bonding: only use primary address for ARP That patch was good because it prevented bonds using ARP monitoring from sending frames with an invalid source IP address. Unfortunately, it didn't always work as expected. When using an ioctl (like ifconfig does) to set the IP address and netmask, 2 separate ioctls are actually called to set the IP and netmask if the mask chosen doesn't match the standard mask for that class of address. The first ioctl did not have a mask that matched the one in the primary address and would still cause the device address to be overwritten. The second ioctl that was called to set the mask would then detect as secondary and ignored, but the damage was already done. This was not an issue when using an application that used netlink sockets as the setting of IP and netmask came down at once. The inconsistent behavior between those two interfaces was something that needed to be resolved. While I was thinking about how I wanted to resolve this, Ralf Zeidler came with a patch that resolved this on a RHEL kernel by keeping a full shadow of the entries in dev->ifa_list for the bonding device and vlan devices in the bonding driver. I didn't like the duplication of the list as I want to see the 'bonding' struct and code shrink rather than grow, but liked the general idea. As the Subject indicates this patch drops the master_ip and vlan_ip elements from the 'bonding' and 'vlan_entry' structs, respectively. This can be done because a device's address-list is now traversed to determine the optimal source IP address for ARP requests and for checks to see if the bonding device has a particular IP address. This code could have all be contained inside the bonding driver, but it made more sense to me to EXPORT and call inet_confirm_addr since it did exactly what was needed. I tested this and a backported patch and everything works as expected. Ralf also helped with verification of the backported patch. Thanks to Ralf for all his help on this. v2: Whitespace and organizational changes based on suggestions from Jay Vosburgh and Dave Miller. v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's suggestion. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> CC: Ralf Zeidler <ralf.zeidler@nsn.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-22 16:14:29 +00:00
addr, vlan_id);
continue;
}
if (net_ratelimit()) {
pr_warning("%s: no path to arp_ip_target %pI4 via rt.dev %s\n",
bond->dev->name, &targets[i],
rt->dst.dev ? rt->dst.dev->name : "NULL");
}
ip_rt_put(rt);
}
}
static void bond_validate_arp(struct bonding *bond, struct slave *slave, __be32 sip, __be32 tip)
{
int i;
__be32 *targets = bond->params.arp_targets;
for (i = 0; (i < BOND_MAX_ARP_TARGETS) && targets[i]; i++) {
pr_debug("bva: sip %pI4 tip %pI4 t[%d] %pI4 bhti(tip) %d\n",
&sip, &tip, i, &targets[i],
bond_has_this_ip(bond, tip));
if (sip == targets[i]) {
if (bond_has_this_ip(bond, tip))
slave->last_arp_rx = jiffies;
return;
}
}
}
static int bond_arp_rcv(const struct sk_buff *skb, struct bonding *bond,
struct slave *slave)
{
struct arphdr *arp = (struct arphdr *)skb->data;
unsigned char *arp_ptr;
__be32 sip, tip;
int alen;
if (skb->protocol != __cpu_to_be16(ETH_P_ARP))
return RX_HANDLER_ANOTHER;
read_lock(&bond->lock);
alen = arp_hdr_len(bond->dev);
pr_debug("bond_arp_rcv: bond %s skb->dev %s\n",
bond->dev->name, skb->dev->name);
if (alen > skb_headlen(skb)) {
arp = kmalloc(alen, GFP_ATOMIC);
if (!arp)
goto out_unlock;
if (skb_copy_bits(skb, 0, arp, alen) < 0)
goto out_unlock;
}
if (arp->ar_hln != bond->dev->addr_len ||
skb->pkt_type == PACKET_OTHERHOST ||
skb->pkt_type == PACKET_LOOPBACK ||
arp->ar_hrd != htons(ARPHRD_ETHER) ||
arp->ar_pro != htons(ETH_P_IP) ||
arp->ar_pln != 4)
goto out_unlock;
arp_ptr = (unsigned char *)(arp + 1);
arp_ptr += bond->dev->addr_len;
memcpy(&sip, arp_ptr, 4);
arp_ptr += 4 + bond->dev->addr_len;
memcpy(&tip, arp_ptr, 4);
pr_debug("bond_arp_rcv: %s %s/%d av %d sv %d sip %pI4 tip %pI4\n",
bond->dev->name, slave->dev->name, bond_slave_state(slave),
bond->params.arp_validate, slave_do_arp_validate(bond, slave),
&sip, &tip);
/*
* Backup slaves won't see the ARP reply, but do come through
* here for each ARP probe (so we swap the sip/tip to validate
* the probe). In a "redundant switch, common router" type of
* configuration, the ARP probe will (hopefully) travel from
* the active, through one switch, the router, then the other
* switch before reaching the backup.
*/
if (bond_is_active_slave(slave))
bond_validate_arp(bond, slave, sip, tip);
else
bond_validate_arp(bond, slave, tip, sip);
out_unlock:
read_unlock(&bond->lock);
if (arp != (struct arphdr *)skb->data)
kfree(arp);
return RX_HANDLER_ANOTHER;
}
/*
* this function is called regularly to monitor each slave's link
* ensuring that traffic is being sent and received when arp monitoring
* is used in load-balancing mode. if the adapter has been dormant, then an
* arp is transmitted to generate traffic. see activebackup_arp_monitor for
* arp monitoring in active backup mode.
*/
void bond_loadbalance_arp_mon(struct work_struct *work)
{
struct bonding *bond = container_of(work, struct bonding,
arp_work.work);
struct slave *slave, *oldcurrent;
int do_failover = 0;
int delta_in_ticks, extra_ticks;
int i;
read_lock(&bond->lock);
delta_in_ticks = msecs_to_jiffies(bond->params.arp_interval);
extra_ticks = delta_in_ticks / 2;
if (bond->slave_cnt == 0)
goto re_arm;
read_lock(&bond->curr_slave_lock);
oldcurrent = bond->curr_active_slave;
read_unlock(&bond->curr_slave_lock);
/* see if any of the previous devices are up now (i.e. they have
* xmt and rcv traffic). the curr_active_slave does not come into
* the picture unless it is null. also, slave->jiffies is not needed
* here because we send an arp on each slave and give a slave as
* long as it needs to get the tx/rx within the delta.
* TODO: what about up/down delay in arp mode? it wasn't here before
* so it can wait
*/
bond_for_each_slave(bond, slave, i) {
unsigned long trans_start = dev_trans_start(slave->dev);
if (slave->link != BOND_LINK_UP) {
if (time_in_range(jiffies,
trans_start - delta_in_ticks,
trans_start + delta_in_ticks + extra_ticks) &&
time_in_range(jiffies,
slave->dev->last_rx - delta_in_ticks,
slave->dev->last_rx + delta_in_ticks + extra_ticks)) {
slave->link = BOND_LINK_UP;
bond_set_active_slave(slave);
/* primary_slave has no meaning in round-robin
* mode. the window of a slave being up and
* curr_active_slave being null after enslaving
* is closed.
*/
if (!oldcurrent) {
pr_info("%s: link status definitely up for interface %s, ",
bond->dev->name,
slave->dev->name);
do_failover = 1;
} else {
pr_info("%s: interface %s is now up\n",
bond->dev->name,
slave->dev->name);
}
}
} else {
/* slave->link == BOND_LINK_UP */
/* not all switches will respond to an arp request
* when the source ip is 0, so don't take the link down
* if we don't know our ip yet
*/
if (!time_in_range(jiffies,
trans_start - delta_in_ticks,
trans_start + 2 * delta_in_ticks + extra_ticks) ||
!time_in_range(jiffies,
slave->dev->last_rx - delta_in_ticks,
slave->dev->last_rx + 2 * delta_in_ticks + extra_ticks)) {
slave->link = BOND_LINK_DOWN;
bond_set_backup_slave(slave);
if (slave->link_failure_count < UINT_MAX)
slave->link_failure_count++;
pr_info("%s: interface %s is now down.\n",
bond->dev->name,
slave->dev->name);
if (slave == oldcurrent)
do_failover = 1;
}
}
/* note: if switch is in round-robin mode, all links
* must tx arp to ensure all links rx an arp - otherwise
* links may oscillate or not come up at all; if switch is
* in something like xor mode, there is nothing we can
* do - all replies will be rx'ed on same link causing slaves
* to be unstable during low/no traffic periods
*/
if (IS_UP(slave->dev))
bond_arp_send_all(bond, slave);
}
if (do_failover) {
block_netpoll_tx();
write_lock_bh(&bond->curr_slave_lock);
bond_select_active_slave(bond);
write_unlock_bh(&bond->curr_slave_lock);
unblock_netpoll_tx();
}
re_arm:
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
if (bond->params.arp_interval)
queue_delayed_work(bond->wq, &bond->arp_work, delta_in_ticks);
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
read_unlock(&bond->lock);
}
/*
* Called to inspect slaves for active-backup mode ARP monitor link state
* changes. Sets new_link in slaves to specify what action should take
* place for the slave. Returns 0 if no changes are found, >0 if changes
* to link states must be committed.
*
* Called with bond->lock held for read.
*/
static int bond_ab_arp_inspect(struct bonding *bond, int delta_in_ticks)
{
struct slave *slave;
int i, commit = 0;
unsigned long trans_start;
int extra_ticks;
/* All the time comparisons below need some extra time. Otherwise, on
* fast networks the ARP probe/reply may arrive within the same jiffy
* as it was sent. Then, the next time the ARP monitor is run, one
* arp_interval will already have passed in the comparisons.
*/
extra_ticks = delta_in_ticks / 2;
bond_for_each_slave(bond, slave, i) {
slave->new_link = BOND_LINK_NOCHANGE;
if (slave->link != BOND_LINK_UP) {
if (time_in_range(jiffies,
slave_last_rx(bond, slave) - delta_in_ticks,
slave_last_rx(bond, slave) + delta_in_ticks + extra_ticks)) {
slave->new_link = BOND_LINK_UP;
commit++;
}
continue;
}
/*
* Give slaves 2*delta after being enslaved or made
* active. This avoids bouncing, as the last receive
* times need a full ARP monitor cycle to be updated.
*/
if (time_in_range(jiffies,
slave->jiffies - delta_in_ticks,
slave->jiffies + 2 * delta_in_ticks + extra_ticks))
continue;
/*
* Backup slave is down if:
* - No current_arp_slave AND
* - more than 3*delta since last receive AND
* - the bond has an IP address
*
* Note: a non-null current_arp_slave indicates
* the curr_active_slave went down and we are
* searching for a new one; under this condition
* we only take the curr_active_slave down - this
* gives each slave a chance to tx/rx traffic
* before being taken out
*/
if (!bond_is_active_slave(slave) &&
!bond->current_arp_slave &&
!time_in_range(jiffies,
slave_last_rx(bond, slave) - delta_in_ticks,
slave_last_rx(bond, slave) + 3 * delta_in_ticks + extra_ticks)) {
slave->new_link = BOND_LINK_DOWN;
commit++;
}
/*
* Active slave is down if:
* - more than 2*delta since transmitting OR
* - (more than 2*delta since receive AND
* the bond has an IP address)
*/
trans_start = dev_trans_start(slave->dev);
if (bond_is_active_slave(slave) &&
(!time_in_range(jiffies,
trans_start - delta_in_ticks,
trans_start + 2 * delta_in_ticks + extra_ticks) ||
!time_in_range(jiffies,
slave_last_rx(bond, slave) - delta_in_ticks,
slave_last_rx(bond, slave) + 2 * delta_in_ticks + extra_ticks))) {
slave->new_link = BOND_LINK_DOWN;
commit++;
}
}
return commit;
}
/*
* Called to commit link state changes noted by inspection step of
* active-backup mode ARP monitor.
*
* Called with RTNL and bond->lock for read.
*/
static void bond_ab_arp_commit(struct bonding *bond, int delta_in_ticks)
{
struct slave *slave;
int i;
unsigned long trans_start;
bond_for_each_slave(bond, slave, i) {
switch (slave->new_link) {
case BOND_LINK_NOCHANGE:
continue;
case BOND_LINK_UP:
trans_start = dev_trans_start(slave->dev);
if ((!bond->curr_active_slave &&
time_in_range(jiffies,
trans_start - delta_in_ticks,
trans_start + delta_in_ticks + delta_in_ticks / 2)) ||
bond->curr_active_slave != slave) {
slave->link = BOND_LINK_UP;
if (bond->current_arp_slave) {
bond_set_slave_inactive_flags(
bond->current_arp_slave);
bond->current_arp_slave = NULL;
}
pr_info("%s: link status definitely up for interface %s.\n",
bond->dev->name, slave->dev->name);
if (!bond->curr_active_slave ||
(slave == bond->primary_slave))
goto do_failover;
}
continue;
case BOND_LINK_DOWN:
if (slave->link_failure_count < UINT_MAX)
slave->link_failure_count++;
slave->link = BOND_LINK_DOWN;
bond_set_slave_inactive_flags(slave);
pr_info("%s: link status definitely down for interface %s, disabling it\n",
bond->dev->name, slave->dev->name);
if (slave == bond->curr_active_slave) {
bond->current_arp_slave = NULL;
goto do_failover;
}
continue;
default:
pr_err("%s: impossible: new_link %d on slave %s\n",
bond->dev->name, slave->new_link,
slave->dev->name);
continue;
}
do_failover:
ASSERT_RTNL();
block_netpoll_tx();
write_lock_bh(&bond->curr_slave_lock);
bond_select_active_slave(bond);
write_unlock_bh(&bond->curr_slave_lock);
unblock_netpoll_tx();
}
bond_set_carrier(bond);
}
/*
* Send ARP probes for active-backup mode ARP monitor.
*
* Called with bond->lock held for read.
*/
static void bond_ab_arp_probe(struct bonding *bond)
{
struct slave *slave;
int i;
read_lock(&bond->curr_slave_lock);
if (bond->current_arp_slave && bond->curr_active_slave)
pr_info("PROBE: c_arp %s && cas %s BAD\n",
bond->current_arp_slave->dev->name,
bond->curr_active_slave->dev->name);
if (bond->curr_active_slave) {
bond_arp_send_all(bond, bond->curr_active_slave);
read_unlock(&bond->curr_slave_lock);
return;
}
read_unlock(&bond->curr_slave_lock);
/* if we don't have a curr_active_slave, search for the next available
* backup slave from the current_arp_slave and make it the candidate
* for becoming the curr_active_slave
*/
if (!bond->current_arp_slave) {
bond->current_arp_slave = bond->first_slave;
if (!bond->current_arp_slave)
return;
}
bond_set_slave_inactive_flags(bond->current_arp_slave);
/* search for next candidate */
bond_for_each_slave_from(bond, slave, i, bond->current_arp_slave->next) {
if (IS_UP(slave->dev)) {
slave->link = BOND_LINK_BACK;
bond_set_slave_active_flags(slave);
bond_arp_send_all(bond, slave);
slave->jiffies = jiffies;
bond->current_arp_slave = slave;
break;
}
/* if the link state is up at this point, we
* mark it down - this can happen if we have
* simultaneous link failures and
* reselect_active_interface doesn't make this
* one the current slave so it is still marked
* up when it is actually down
*/
if (slave->link == BOND_LINK_UP) {
slave->link = BOND_LINK_DOWN;
if (slave->link_failure_count < UINT_MAX)
slave->link_failure_count++;
bond_set_slave_inactive_flags(slave);
pr_info("%s: backup interface %s is now down.\n",
bond->dev->name, slave->dev->name);
}
}
}
void bond_activebackup_arp_mon(struct work_struct *work)
{
struct bonding *bond = container_of(work, struct bonding,
arp_work.work);
bool should_notify_peers = false;
int delta_in_ticks;
read_lock(&bond->lock);
delta_in_ticks = msecs_to_jiffies(bond->params.arp_interval);
if (bond->slave_cnt == 0)
goto re_arm;
should_notify_peers = bond_should_notify_peers(bond);
if (bond_ab_arp_inspect(bond, delta_in_ticks)) {
read_unlock(&bond->lock);
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
/* Race avoidance with bond_close flush of workqueue */
if (!rtnl_trylock()) {
read_lock(&bond->lock);
delta_in_ticks = 1;
should_notify_peers = false;
goto re_arm;
}
read_lock(&bond->lock);
bond_ab_arp_commit(bond, delta_in_ticks);
read_unlock(&bond->lock);
rtnl_unlock();
read_lock(&bond->lock);
}
bond_ab_arp_probe(bond);
re_arm:
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
if (bond->params.arp_interval)
queue_delayed_work(bond->wq, &bond->arp_work, delta_in_ticks);
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
read_unlock(&bond->lock);
if (should_notify_peers) {
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
if (!rtnl_trylock()) {
read_lock(&bond->lock);
bond->send_peer_notif++;
read_unlock(&bond->lock);
return;
}
call_netdevice_notifiers(NETDEV_NOTIFY_PEERS, bond->dev);
rtnl_unlock();
}
}
/*-------------------------- netdev event handling --------------------------*/
/*
* Change device name
*/
static int bond_event_changename(struct bonding *bond)
{
bond_remove_proc_entry(bond);
bond_create_proc_entry(bond);
bond_debug_reregister(bond);
return NOTIFY_DONE;
}
static int bond_master_netdev_event(unsigned long event,
struct net_device *bond_dev)
{
struct bonding *event_bond = netdev_priv(bond_dev);
switch (event) {
case NETDEV_CHANGENAME:
return bond_event_changename(event_bond);
case NETDEV_UNREGISTER:
bond_remove_proc_entry(event_bond);
break;
case NETDEV_REGISTER:
bond_create_proc_entry(event_bond);
break;
default:
break;
}
return NOTIFY_DONE;
}
static int bond_slave_netdev_event(unsigned long event,
struct net_device *slave_dev)
{
struct net_device *bond_dev = slave_dev->master;
struct bonding *bond = netdev_priv(bond_dev);
struct slave *slave = NULL;
switch (event) {
case NETDEV_UNREGISTER:
if (bond_dev) {
if (bond->setup_by_slave)
bond_release_and_destroy(bond_dev, slave_dev);
else
bond_release(bond_dev, slave_dev);
}
break;
case NETDEV_UP:
case NETDEV_CHANGE:
slave = bond_get_slave_by_dev(bond, slave_dev);
if (slave) {
u32 old_speed = slave->speed;
u8 old_duplex = slave->duplex;
bond_update_speed_duplex(slave);
if (bond->params.mode == BOND_MODE_8023AD) {
if (old_speed != slave->speed)
bond_3ad_adapter_speed_changed(slave);
if (old_duplex != slave->duplex)
bond_3ad_adapter_duplex_changed(slave);
}
}
break;
case NETDEV_DOWN:
/*
* ... Or is it this?
*/
break;
case NETDEV_CHANGEMTU:
/*
* TODO: Should slaves be allowed to
* independently alter their MTU? For
* an active-backup bond, slaves need
* not be the same type of device, so
* MTUs may vary. For other modes,
* slaves arguably should have the
* same MTUs. To do this, we'd need to
* take over the slave's change_mtu
* function for the duration of their
* servitude.
*/
break;
case NETDEV_CHANGENAME:
/*
* TODO: handle changing the primary's name
*/
break;
case NETDEV_FEAT_CHANGE:
bond_compute_features(bond);
break;
default:
break;
}
return NOTIFY_DONE;
}
/*
* bond_netdev_event: handle netdev notifier chain events.
*
* This function receives events for the netdev chain. The caller (an
[PATCH] Notifier chain update: API changes The kernel's implementation of notifier chains is unsafe. There is no protection against entries being added to or removed from a chain while the chain is in use. The issues were discussed in this thread: http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2 We noticed that notifier chains in the kernel fall into two basic usage classes: "Blocking" chains are always called from a process context and the callout routines are allowed to sleep; "Atomic" chains can be called from an atomic context and the callout routines are not allowed to sleep. We decided to codify this distinction and make it part of the API. Therefore this set of patches introduces three new, parallel APIs: one for blocking notifiers, one for atomic notifiers, and one for "raw" notifiers (which is really just the old API under a new name). New kinds of data structures are used for the heads of the chains, and new routines are defined for registration, unregistration, and calling a chain. The three APIs are explained in include/linux/notifier.h and their implementation is in kernel/sys.c. With atomic and blocking chains, the implementation guarantees that the chain links will not be corrupted and that chain callers will not get messed up by entries being added or removed. For raw chains the implementation provides no guarantees at all; users of this API must provide their own protections. (The idea was that situations may come up where the assumptions of the atomic and blocking APIs are not appropriate, so it should be possible for users to handle these things in their own way.) There are some limitations, which should not be too hard to live with. For atomic/blocking chains, registration and unregistration must always be done in a process context since the chain is protected by a mutex/rwsem. Also, a callout routine for a non-raw chain must not try to register or unregister entries on its own chain. (This did happen in a couple of places and the code had to be changed to avoid it.) Since atomic chains may be called from within an NMI handler, they cannot use spinlocks for synchronization. Instead we use RCU. The overhead falls almost entirely in the unregister routine, which is okay since unregistration is much less frequent that calling a chain. Here is the list of chains that we adjusted and their classifications. None of them use the raw API, so for the moment it is only a placeholder. ATOMIC CHAINS ------------- arch/i386/kernel/traps.c: i386die_chain arch/ia64/kernel/traps.c: ia64die_chain arch/powerpc/kernel/traps.c: powerpc_die_chain arch/sparc64/kernel/traps.c: sparc64die_chain arch/x86_64/kernel/traps.c: die_chain drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list kernel/panic.c: panic_notifier_list kernel/profile.c: task_free_notifier net/bluetooth/hci_core.c: hci_notifier net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain net/ipv6/addrconf.c: inet6addr_chain net/netfilter/nf_conntrack_core.c: nf_conntrack_chain net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain net/netlink/af_netlink.c: netlink_chain BLOCKING CHAINS --------------- arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain arch/s390/kernel/process.c: idle_chain arch/x86_64/kernel/process.c idle_notifier drivers/base/memory.c: memory_chain drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list drivers/macintosh/adb.c: adb_client_list drivers/macintosh/via-pmu.c sleep_notifier_list drivers/macintosh/via-pmu68k.c sleep_notifier_list drivers/macintosh/windfarm_core.c wf_client_list drivers/usb/core/notify.c usb_notifier_list drivers/video/fbmem.c fb_notifier_list kernel/cpu.c cpu_chain kernel/module.c module_notify_list kernel/profile.c munmap_notifier kernel/profile.c task_exit_notifier kernel/sys.c reboot_notifier_list net/core/dev.c netdev_chain net/decnet/dn_dev.c: dnaddr_chain net/ipv4/devinet.c: inetaddr_chain It's possible that some of these classifications are wrong. If they are, please let us know or submit a patch to fix them. Note that any chain that gets called very frequently should be atomic, because the rwsem read-locking used for blocking chains is very likely to incur cache misses on SMP systems. (However, if the chain's callout routines may sleep then the chain cannot be atomic.) The patch set was written by Alan Stern and Chandra Seetharaman, incorporating material written by Keith Owens and suggestions from Paul McKenney and Andrew Morton. [jes@sgi.com: restructure the notifier chain initialization macros] Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: Jes Sorensen <jes@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-27 09:16:30 +00:00
* ioctl handler calling blocking_notifier_call_chain) holds the necessary
* locks for us to safely manipulate the slave devices (RTNL lock,
* dev_probe_lock).
*/
static int bond_netdev_event(struct notifier_block *this,
unsigned long event, void *ptr)
{
struct net_device *event_dev = (struct net_device *)ptr;
pr_debug("event_dev: %s, event: %lx\n",
event_dev ? event_dev->name : "None",
event);
if (!(event_dev->priv_flags & IFF_BONDING))
return NOTIFY_DONE;
if (event_dev->flags & IFF_MASTER) {
pr_debug("IFF_MASTER\n");
return bond_master_netdev_event(event, event_dev);
}
if (event_dev->flags & IFF_SLAVE) {
pr_debug("IFF_SLAVE\n");
return bond_slave_netdev_event(event, event_dev);
}
return NOTIFY_DONE;
}
static struct notifier_block bond_netdev_notifier = {
.notifier_call = bond_netdev_event,
};
/*---------------------------- Hashing Policies -----------------------------*/
bonding: support for IPv6 transmit hashing Currently the "bonding" driver does not support load balancing outgoing traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4) are currently supported; this patch adds transmit hashing for IPv6 (and TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the bonding driver. In addition, bounds checking has been added to all transmit hashing functions. The algorithm chosen (xor'ing the bottom three quads of the source and destination addresses together, then xor'ing each byte of that result into the bottom byte, finally xor'ing with the last bytes of the MAC addresses) was selected after testing almost 400,000 unique IPv6 addresses harvested from server logs. This algorithm had the most even distribution for both big- and little-endian architectures while still using few instructions. Its behavior also attempts to closely match that of the IPv4 algorithm. The IPv6 flow label was intentionally not included in the hash as it appears to be unset in the vast majority of IPv6 traffic sampled, and the current algorithm not using the flow label already offers a very even distribution. Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets, ie, they are not balanced based on layer 4 information. Additionally, IPv6 packets with intermediate headers are not balanced based on layer 4 information. In practice these intermediate headers are not common and this should not cause any problems, and the alternative (a packet-parsing loop and look-up table) seemed slow and complicated for little gain. Tested-by: John Eaglesham <linux@8192.net> Signed-off-by: John Eaglesham <linux@8192.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-21 20:43:35 +00:00
/*
* Hash for the output device based upon layer 2 data
*/
static int bond_xmit_hash_policy_l2(struct sk_buff *skb, int count)
{
struct ethhdr *data = (struct ethhdr *)skb->data;
if (skb_headlen(skb) >= offsetof(struct ethhdr, h_proto))
return (data->h_dest[5] ^ data->h_source[5]) % count;
return 0;
}
/*
* Hash for the output device based upon layer 2 and layer 3 data. If
bonding: support for IPv6 transmit hashing Currently the "bonding" driver does not support load balancing outgoing traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4) are currently supported; this patch adds transmit hashing for IPv6 (and TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the bonding driver. In addition, bounds checking has been added to all transmit hashing functions. The algorithm chosen (xor'ing the bottom three quads of the source and destination addresses together, then xor'ing each byte of that result into the bottom byte, finally xor'ing with the last bytes of the MAC addresses) was selected after testing almost 400,000 unique IPv6 addresses harvested from server logs. This algorithm had the most even distribution for both big- and little-endian architectures while still using few instructions. Its behavior also attempts to closely match that of the IPv4 algorithm. The IPv6 flow label was intentionally not included in the hash as it appears to be unset in the vast majority of IPv6 traffic sampled, and the current algorithm not using the flow label already offers a very even distribution. Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets, ie, they are not balanced based on layer 4 information. Additionally, IPv6 packets with intermediate headers are not balanced based on layer 4 information. In practice these intermediate headers are not common and this should not cause any problems, and the alternative (a packet-parsing loop and look-up table) seemed slow and complicated for little gain. Tested-by: John Eaglesham <linux@8192.net> Signed-off-by: John Eaglesham <linux@8192.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-21 20:43:35 +00:00
* the packet is not IP, fall back on bond_xmit_hash_policy_l2()
*/
static int bond_xmit_hash_policy_l23(struct sk_buff *skb, int count)
{
struct ethhdr *data = (struct ethhdr *)skb->data;
bonding: support for IPv6 transmit hashing Currently the "bonding" driver does not support load balancing outgoing traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4) are currently supported; this patch adds transmit hashing for IPv6 (and TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the bonding driver. In addition, bounds checking has been added to all transmit hashing functions. The algorithm chosen (xor'ing the bottom three quads of the source and destination addresses together, then xor'ing each byte of that result into the bottom byte, finally xor'ing with the last bytes of the MAC addresses) was selected after testing almost 400,000 unique IPv6 addresses harvested from server logs. This algorithm had the most even distribution for both big- and little-endian architectures while still using few instructions. Its behavior also attempts to closely match that of the IPv4 algorithm. The IPv6 flow label was intentionally not included in the hash as it appears to be unset in the vast majority of IPv6 traffic sampled, and the current algorithm not using the flow label already offers a very even distribution. Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets, ie, they are not balanced based on layer 4 information. Additionally, IPv6 packets with intermediate headers are not balanced based on layer 4 information. In practice these intermediate headers are not common and this should not cause any problems, and the alternative (a packet-parsing loop and look-up table) seemed slow and complicated for little gain. Tested-by: John Eaglesham <linux@8192.net> Signed-off-by: John Eaglesham <linux@8192.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-21 20:43:35 +00:00
struct iphdr *iph;
struct ipv6hdr *ipv6h;
u32 v6hash;
__be32 *s, *d;
if (skb->protocol == htons(ETH_P_IP) &&
skb_network_header_len(skb) >= sizeof(*iph)) {
iph = ip_hdr(skb);
return ((ntohl(iph->saddr ^ iph->daddr) & 0xffff) ^
(data->h_dest[5] ^ data->h_source[5])) % count;
bonding: support for IPv6 transmit hashing Currently the "bonding" driver does not support load balancing outgoing traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4) are currently supported; this patch adds transmit hashing for IPv6 (and TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the bonding driver. In addition, bounds checking has been added to all transmit hashing functions. The algorithm chosen (xor'ing the bottom three quads of the source and destination addresses together, then xor'ing each byte of that result into the bottom byte, finally xor'ing with the last bytes of the MAC addresses) was selected after testing almost 400,000 unique IPv6 addresses harvested from server logs. This algorithm had the most even distribution for both big- and little-endian architectures while still using few instructions. Its behavior also attempts to closely match that of the IPv4 algorithm. The IPv6 flow label was intentionally not included in the hash as it appears to be unset in the vast majority of IPv6 traffic sampled, and the current algorithm not using the flow label already offers a very even distribution. Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets, ie, they are not balanced based on layer 4 information. Additionally, IPv6 packets with intermediate headers are not balanced based on layer 4 information. In practice these intermediate headers are not common and this should not cause any problems, and the alternative (a packet-parsing loop and look-up table) seemed slow and complicated for little gain. Tested-by: John Eaglesham <linux@8192.net> Signed-off-by: John Eaglesham <linux@8192.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-21 20:43:35 +00:00
} else if (skb->protocol == htons(ETH_P_IPV6) &&
skb_network_header_len(skb) >= sizeof(*ipv6h)) {
ipv6h = ipv6_hdr(skb);
s = &ipv6h->saddr.s6_addr32[0];
d = &ipv6h->daddr.s6_addr32[0];
v6hash = (s[1] ^ d[1]) ^ (s[2] ^ d[2]) ^ (s[3] ^ d[3]);
v6hash ^= (v6hash >> 24) ^ (v6hash >> 16) ^ (v6hash >> 8);
return (v6hash ^ data->h_dest[5] ^ data->h_source[5]) % count;
}
bonding: support for IPv6 transmit hashing Currently the "bonding" driver does not support load balancing outgoing traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4) are currently supported; this patch adds transmit hashing for IPv6 (and TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the bonding driver. In addition, bounds checking has been added to all transmit hashing functions. The algorithm chosen (xor'ing the bottom three quads of the source and destination addresses together, then xor'ing each byte of that result into the bottom byte, finally xor'ing with the last bytes of the MAC addresses) was selected after testing almost 400,000 unique IPv6 addresses harvested from server logs. This algorithm had the most even distribution for both big- and little-endian architectures while still using few instructions. Its behavior also attempts to closely match that of the IPv4 algorithm. The IPv6 flow label was intentionally not included in the hash as it appears to be unset in the vast majority of IPv6 traffic sampled, and the current algorithm not using the flow label already offers a very even distribution. Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets, ie, they are not balanced based on layer 4 information. Additionally, IPv6 packets with intermediate headers are not balanced based on layer 4 information. In practice these intermediate headers are not common and this should not cause any problems, and the alternative (a packet-parsing loop and look-up table) seemed slow and complicated for little gain. Tested-by: John Eaglesham <linux@8192.net> Signed-off-by: John Eaglesham <linux@8192.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-21 20:43:35 +00:00
return bond_xmit_hash_policy_l2(skb, count);
}
/*
* Hash for the output device based upon layer 3 and layer 4 data. If
* the packet is a frag or not TCP or UDP, just use layer 3 data. If it is
bonding: support for IPv6 transmit hashing Currently the "bonding" driver does not support load balancing outgoing traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4) are currently supported; this patch adds transmit hashing for IPv6 (and TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the bonding driver. In addition, bounds checking has been added to all transmit hashing functions. The algorithm chosen (xor'ing the bottom three quads of the source and destination addresses together, then xor'ing each byte of that result into the bottom byte, finally xor'ing with the last bytes of the MAC addresses) was selected after testing almost 400,000 unique IPv6 addresses harvested from server logs. This algorithm had the most even distribution for both big- and little-endian architectures while still using few instructions. Its behavior also attempts to closely match that of the IPv4 algorithm. The IPv6 flow label was intentionally not included in the hash as it appears to be unset in the vast majority of IPv6 traffic sampled, and the current algorithm not using the flow label already offers a very even distribution. Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets, ie, they are not balanced based on layer 4 information. Additionally, IPv6 packets with intermediate headers are not balanced based on layer 4 information. In practice these intermediate headers are not common and this should not cause any problems, and the alternative (a packet-parsing loop and look-up table) seemed slow and complicated for little gain. Tested-by: John Eaglesham <linux@8192.net> Signed-off-by: John Eaglesham <linux@8192.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-21 20:43:35 +00:00
* altogether not IP, fall back on bond_xmit_hash_policy_l2()
*/
static int bond_xmit_hash_policy_l34(struct sk_buff *skb, int count)
{
bonding: support for IPv6 transmit hashing Currently the "bonding" driver does not support load balancing outgoing traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4) are currently supported; this patch adds transmit hashing for IPv6 (and TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the bonding driver. In addition, bounds checking has been added to all transmit hashing functions. The algorithm chosen (xor'ing the bottom three quads of the source and destination addresses together, then xor'ing each byte of that result into the bottom byte, finally xor'ing with the last bytes of the MAC addresses) was selected after testing almost 400,000 unique IPv6 addresses harvested from server logs. This algorithm had the most even distribution for both big- and little-endian architectures while still using few instructions. Its behavior also attempts to closely match that of the IPv4 algorithm. The IPv6 flow label was intentionally not included in the hash as it appears to be unset in the vast majority of IPv6 traffic sampled, and the current algorithm not using the flow label already offers a very even distribution. Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets, ie, they are not balanced based on layer 4 information. Additionally, IPv6 packets with intermediate headers are not balanced based on layer 4 information. In practice these intermediate headers are not common and this should not cause any problems, and the alternative (a packet-parsing loop and look-up table) seemed slow and complicated for little gain. Tested-by: John Eaglesham <linux@8192.net> Signed-off-by: John Eaglesham <linux@8192.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-21 20:43:35 +00:00
u32 layer4_xor = 0;
struct iphdr *iph;
struct ipv6hdr *ipv6h;
__be32 *s, *d;
__be16 *layer4hdr;
bonding: support for IPv6 transmit hashing Currently the "bonding" driver does not support load balancing outgoing traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4) are currently supported; this patch adds transmit hashing for IPv6 (and TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the bonding driver. In addition, bounds checking has been added to all transmit hashing functions. The algorithm chosen (xor'ing the bottom three quads of the source and destination addresses together, then xor'ing each byte of that result into the bottom byte, finally xor'ing with the last bytes of the MAC addresses) was selected after testing almost 400,000 unique IPv6 addresses harvested from server logs. This algorithm had the most even distribution for both big- and little-endian architectures while still using few instructions. Its behavior also attempts to closely match that of the IPv4 algorithm. The IPv6 flow label was intentionally not included in the hash as it appears to be unset in the vast majority of IPv6 traffic sampled, and the current algorithm not using the flow label already offers a very even distribution. Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets, ie, they are not balanced based on layer 4 information. Additionally, IPv6 packets with intermediate headers are not balanced based on layer 4 information. In practice these intermediate headers are not common and this should not cause any problems, and the alternative (a packet-parsing loop and look-up table) seemed slow and complicated for little gain. Tested-by: John Eaglesham <linux@8192.net> Signed-off-by: John Eaglesham <linux@8192.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-21 20:43:35 +00:00
if (skb->protocol == htons(ETH_P_IP) &&
skb_network_header_len(skb) >= sizeof(*iph)) {
iph = ip_hdr(skb);
if (!ip_is_fragment(iph) &&
(iph->protocol == IPPROTO_TCP ||
bonding: support for IPv6 transmit hashing Currently the "bonding" driver does not support load balancing outgoing traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4) are currently supported; this patch adds transmit hashing for IPv6 (and TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the bonding driver. In addition, bounds checking has been added to all transmit hashing functions. The algorithm chosen (xor'ing the bottom three quads of the source and destination addresses together, then xor'ing each byte of that result into the bottom byte, finally xor'ing with the last bytes of the MAC addresses) was selected after testing almost 400,000 unique IPv6 addresses harvested from server logs. This algorithm had the most even distribution for both big- and little-endian architectures while still using few instructions. Its behavior also attempts to closely match that of the IPv4 algorithm. The IPv6 flow label was intentionally not included in the hash as it appears to be unset in the vast majority of IPv6 traffic sampled, and the current algorithm not using the flow label already offers a very even distribution. Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets, ie, they are not balanced based on layer 4 information. Additionally, IPv6 packets with intermediate headers are not balanced based on layer 4 information. In practice these intermediate headers are not common and this should not cause any problems, and the alternative (a packet-parsing loop and look-up table) seemed slow and complicated for little gain. Tested-by: John Eaglesham <linux@8192.net> Signed-off-by: John Eaglesham <linux@8192.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-21 20:43:35 +00:00
iph->protocol == IPPROTO_UDP) &&
(skb_headlen(skb) - skb_network_offset(skb) >=
iph->ihl * sizeof(u32) + sizeof(*layer4hdr) * 2)) {
layer4hdr = (__be16 *)((u32 *)iph + iph->ihl);
layer4_xor = ntohs(*layer4hdr ^ *(layer4hdr + 1));
}
return (layer4_xor ^
((ntohl(iph->saddr ^ iph->daddr)) & 0xffff)) % count;
bonding: support for IPv6 transmit hashing Currently the "bonding" driver does not support load balancing outgoing traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4) are currently supported; this patch adds transmit hashing for IPv6 (and TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the bonding driver. In addition, bounds checking has been added to all transmit hashing functions. The algorithm chosen (xor'ing the bottom three quads of the source and destination addresses together, then xor'ing each byte of that result into the bottom byte, finally xor'ing with the last bytes of the MAC addresses) was selected after testing almost 400,000 unique IPv6 addresses harvested from server logs. This algorithm had the most even distribution for both big- and little-endian architectures while still using few instructions. Its behavior also attempts to closely match that of the IPv4 algorithm. The IPv6 flow label was intentionally not included in the hash as it appears to be unset in the vast majority of IPv6 traffic sampled, and the current algorithm not using the flow label already offers a very even distribution. Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets, ie, they are not balanced based on layer 4 information. Additionally, IPv6 packets with intermediate headers are not balanced based on layer 4 information. In practice these intermediate headers are not common and this should not cause any problems, and the alternative (a packet-parsing loop and look-up table) seemed slow and complicated for little gain. Tested-by: John Eaglesham <linux@8192.net> Signed-off-by: John Eaglesham <linux@8192.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-21 20:43:35 +00:00
} else if (skb->protocol == htons(ETH_P_IPV6) &&
skb_network_header_len(skb) >= sizeof(*ipv6h)) {
ipv6h = ipv6_hdr(skb);
if ((ipv6h->nexthdr == IPPROTO_TCP ||
ipv6h->nexthdr == IPPROTO_UDP) &&
(skb_headlen(skb) - skb_network_offset(skb) >=
sizeof(*ipv6h) + sizeof(*layer4hdr) * 2)) {
layer4hdr = (__be16 *)(ipv6h + 1);
layer4_xor = ntohs(*layer4hdr ^ *(layer4hdr + 1));
}
s = &ipv6h->saddr.s6_addr32[0];
d = &ipv6h->daddr.s6_addr32[0];
layer4_xor ^= (s[1] ^ d[1]) ^ (s[2] ^ d[2]) ^ (s[3] ^ d[3]);
layer4_xor ^= (layer4_xor >> 24) ^ (layer4_xor >> 16) ^
(layer4_xor >> 8);
return layer4_xor % count;
}
bonding: support for IPv6 transmit hashing Currently the "bonding" driver does not support load balancing outgoing traffic in LACP mode for IPv6 traffic. IPv4 (and TCP or UDP over IPv4) are currently supported; this patch adds transmit hashing for IPv6 (and TCP or UDP over IPv6), bringing IPv6 up to par with IPv4 support in the bonding driver. In addition, bounds checking has been added to all transmit hashing functions. The algorithm chosen (xor'ing the bottom three quads of the source and destination addresses together, then xor'ing each byte of that result into the bottom byte, finally xor'ing with the last bytes of the MAC addresses) was selected after testing almost 400,000 unique IPv6 addresses harvested from server logs. This algorithm had the most even distribution for both big- and little-endian architectures while still using few instructions. Its behavior also attempts to closely match that of the IPv4 algorithm. The IPv6 flow label was intentionally not included in the hash as it appears to be unset in the vast majority of IPv6 traffic sampled, and the current algorithm not using the flow label already offers a very even distribution. Fragmented IPv6 packets are handled the same way as fragmented IPv4 packets, ie, they are not balanced based on layer 4 information. Additionally, IPv6 packets with intermediate headers are not balanced based on layer 4 information. In practice these intermediate headers are not common and this should not cause any problems, and the alternative (a packet-parsing loop and look-up table) seemed slow and complicated for little gain. Tested-by: John Eaglesham <linux@8192.net> Signed-off-by: John Eaglesham <linux@8192.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-21 20:43:35 +00:00
return bond_xmit_hash_policy_l2(skb, count);
}
/*-------------------------- Device entry points ----------------------------*/
static int bond_open(struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
struct slave *slave;
int i;
/* reset slave->backup and slave->inactive */
read_lock(&bond->lock);
if (bond->slave_cnt > 0) {
read_lock(&bond->curr_slave_lock);
bond_for_each_slave(bond, slave, i) {
if ((bond->params.mode == BOND_MODE_ACTIVEBACKUP)
&& (slave != bond->curr_active_slave)) {
bond_set_slave_inactive_flags(slave);
} else {
bond_set_slave_active_flags(slave);
}
}
read_unlock(&bond->curr_slave_lock);
}
read_unlock(&bond->lock);
INIT_DELAYED_WORK(&bond->mcast_work, bond_resend_igmp_join_requests_delayed);
if (bond_is_lb(bond)) {
/* bond_alb_initialize must be called before the timer
* is started.
*/
if (bond_alb_initialize(bond, (bond->params.mode == BOND_MODE_ALB))) {
/* something went wrong - fail the open operation */
return -ENOMEM;
}
INIT_DELAYED_WORK(&bond->alb_work, bond_alb_monitor);
queue_delayed_work(bond->wq, &bond->alb_work, 0);
}
if (bond->params.miimon) { /* link check interval, in milliseconds. */
INIT_DELAYED_WORK(&bond->mii_work, bond_mii_monitor);
queue_delayed_work(bond->wq, &bond->mii_work, 0);
}
if (bond->params.arp_interval) { /* arp interval, in milliseconds. */
if (bond->params.mode == BOND_MODE_ACTIVEBACKUP)
INIT_DELAYED_WORK(&bond->arp_work,
bond_activebackup_arp_mon);
else
INIT_DELAYED_WORK(&bond->arp_work,
bond_loadbalance_arp_mon);
queue_delayed_work(bond->wq, &bond->arp_work, 0);
if (bond->params.arp_validate)
bond->recv_probe = bond_arp_rcv;
}
if (bond->params.mode == BOND_MODE_8023AD) {
INIT_DELAYED_WORK(&bond->ad_work, bond_3ad_state_machine_handler);
queue_delayed_work(bond->wq, &bond->ad_work, 0);
/* register to receive LACPDUs */
bond->recv_probe = bond_3ad_lacpdu_recv;
bond_3ad_initiate_agg_selection(bond, 1);
}
return 0;
}
static int bond_close(struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
write_lock_bh(&bond->lock);
bond->send_peer_notif = 0;
write_unlock_bh(&bond->lock);
if (bond->params.miimon) { /* link check interval, in milliseconds. */
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
cancel_delayed_work_sync(&bond->mii_work);
}
if (bond->params.arp_interval) { /* arp interval, in milliseconds. */
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
cancel_delayed_work_sync(&bond->arp_work);
}
switch (bond->params.mode) {
case BOND_MODE_8023AD:
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
cancel_delayed_work_sync(&bond->ad_work);
break;
case BOND_MODE_TLB:
case BOND_MODE_ALB:
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
cancel_delayed_work_sync(&bond->alb_work);
break;
default:
break;
}
if (delayed_work_pending(&bond->mcast_work))
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
cancel_delayed_work_sync(&bond->mcast_work);
if (bond_is_lb(bond)) {
/* Must be called only after all
* slaves have been released
*/
bond_alb_deinitialize(bond);
}
bond->recv_probe = NULL;
return 0;
}
static struct rtnl_link_stats64 *bond_get_stats(struct net_device *bond_dev,
struct rtnl_link_stats64 *stats)
{
struct bonding *bond = netdev_priv(bond_dev);
struct rtnl_link_stats64 temp;
struct slave *slave;
int i;
memset(stats, 0, sizeof(*stats));
read_lock_bh(&bond->lock);
bond_for_each_slave(bond, slave, i) {
const struct rtnl_link_stats64 *sstats =
dev_get_stats(slave->dev, &temp);
stats->rx_packets += sstats->rx_packets;
stats->rx_bytes += sstats->rx_bytes;
stats->rx_errors += sstats->rx_errors;
stats->rx_dropped += sstats->rx_dropped;
stats->tx_packets += sstats->tx_packets;
stats->tx_bytes += sstats->tx_bytes;
stats->tx_errors += sstats->tx_errors;
stats->tx_dropped += sstats->tx_dropped;
stats->multicast += sstats->multicast;
stats->collisions += sstats->collisions;
stats->rx_length_errors += sstats->rx_length_errors;
stats->rx_over_errors += sstats->rx_over_errors;
stats->rx_crc_errors += sstats->rx_crc_errors;
stats->rx_frame_errors += sstats->rx_frame_errors;
stats->rx_fifo_errors += sstats->rx_fifo_errors;
stats->rx_missed_errors += sstats->rx_missed_errors;
stats->tx_aborted_errors += sstats->tx_aborted_errors;
stats->tx_carrier_errors += sstats->tx_carrier_errors;
stats->tx_fifo_errors += sstats->tx_fifo_errors;
stats->tx_heartbeat_errors += sstats->tx_heartbeat_errors;
stats->tx_window_errors += sstats->tx_window_errors;
}
read_unlock_bh(&bond->lock);
return stats;
}
static int bond_do_ioctl(struct net_device *bond_dev, struct ifreq *ifr, int cmd)
{
struct net_device *slave_dev = NULL;
struct ifbond k_binfo;
struct ifbond __user *u_binfo = NULL;
struct ifslave k_sinfo;
struct ifslave __user *u_sinfo = NULL;
struct mii_ioctl_data *mii = NULL;
int res = 0;
pr_debug("bond_ioctl: master=%s, cmd=%d\n", bond_dev->name, cmd);
switch (cmd) {
case SIOCGMIIPHY:
mii = if_mii(ifr);
if (!mii)
return -EINVAL;
mii->phy_id = 0;
/* Fall Through */
case SIOCGMIIREG:
/*
* We do this again just in case we were called by SIOCGMIIREG
* instead of SIOCGMIIPHY.
*/
mii = if_mii(ifr);
if (!mii)
return -EINVAL;
if (mii->reg_num == 1) {
struct bonding *bond = netdev_priv(bond_dev);
mii->val_out = 0;
read_lock(&bond->lock);
read_lock(&bond->curr_slave_lock);
if (netif_carrier_ok(bond->dev))
mii->val_out = BMSR_LSTATUS;
read_unlock(&bond->curr_slave_lock);
read_unlock(&bond->lock);
}
return 0;
case BOND_INFO_QUERY_OLD:
case SIOCBONDINFOQUERY:
u_binfo = (struct ifbond __user *)ifr->ifr_data;
if (copy_from_user(&k_binfo, u_binfo, sizeof(ifbond)))
return -EFAULT;
res = bond_info_query(bond_dev, &k_binfo);
if (res == 0 &&
copy_to_user(u_binfo, &k_binfo, sizeof(ifbond)))
return -EFAULT;
return res;
case BOND_SLAVE_INFO_QUERY_OLD:
case SIOCBONDSLAVEINFOQUERY:
u_sinfo = (struct ifslave __user *)ifr->ifr_data;
if (copy_from_user(&k_sinfo, u_sinfo, sizeof(ifslave)))
return -EFAULT;
res = bond_slave_info_query(bond_dev, &k_sinfo);
if (res == 0 &&
copy_to_user(u_sinfo, &k_sinfo, sizeof(ifslave)))
return -EFAULT;
return res;
default:
/* Go on */
break;
}
if (!capable(CAP_NET_ADMIN))
return -EPERM;
slave_dev = dev_get_by_name(dev_net(bond_dev), ifr->ifr_slave);
pr_debug("slave_dev=%p:\n", slave_dev);
if (!slave_dev)
res = -ENODEV;
else {
pr_debug("slave_dev->name=%s:\n", slave_dev->name);
switch (cmd) {
case BOND_ENSLAVE_OLD:
case SIOCBONDENSLAVE:
res = bond_enslave(bond_dev, slave_dev);
break;
case BOND_RELEASE_OLD:
case SIOCBONDRELEASE:
res = bond_release(bond_dev, slave_dev);
break;
case BOND_SETHWADDR_OLD:
case SIOCBONDSETHWADDR:
res = bond_sethwaddr(bond_dev, slave_dev);
break;
case BOND_CHANGE_ACTIVE_OLD:
case SIOCBONDCHANGEACTIVE:
res = bond_ioctl_change_active(bond_dev, slave_dev);
break;
default:
res = -EOPNOTSUPP;
}
dev_put(slave_dev);
}
return res;
}
static bool bond_addr_in_mc_list(unsigned char *addr,
struct netdev_hw_addr_list *list,
int addrlen)
{
struct netdev_hw_addr *ha;
netdev_hw_addr_list_for_each(ha, list)
if (!memcmp(ha->addr, addr, addrlen))
return true;
return false;
}
static void bond_change_rx_flags(struct net_device *bond_dev, int change)
{
struct bonding *bond = netdev_priv(bond_dev);
if (change & IFF_PROMISC)
bond_set_promiscuity(bond,
bond_dev->flags & IFF_PROMISC ? 1 : -1);
if (change & IFF_ALLMULTI)
bond_set_allmulti(bond,
bond_dev->flags & IFF_ALLMULTI ? 1 : -1);
}
static void bond_set_multicast_list(struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
struct netdev_hw_addr *ha;
bool found;
read_lock(&bond->lock);
/* looking for addresses to add to slaves' mc list */
netdev_for_each_mc_addr(ha, bond_dev) {
found = bond_addr_in_mc_list(ha->addr, &bond->mc_list,
bond_dev->addr_len);
if (!found)
bond_mc_add(bond, ha->addr);
}
/* looking for addresses to delete from slaves' list */
netdev_hw_addr_list_for_each(ha, &bond->mc_list) {
found = bond_addr_in_mc_list(ha->addr, &bond_dev->mc,
bond_dev->addr_len);
if (!found)
bond_mc_del(bond, ha->addr);
}
/* save master's multicast list */
__hw_addr_flush(&bond->mc_list);
__hw_addr_add_multiple(&bond->mc_list, &bond_dev->mc,
bond_dev->addr_len, NETDEV_HW_ADDR_T_MULTICAST);
read_unlock(&bond->lock);
}
static int bond_neigh_init(struct neighbour *n)
{
struct bonding *bond = netdev_priv(n->dev);
struct slave *slave = bond->first_slave;
const struct net_device_ops *slave_ops;
struct neigh_parms parms;
int ret;
if (!slave)
return 0;
slave_ops = slave->dev->netdev_ops;
if (!slave_ops->ndo_neigh_setup)
return 0;
parms.neigh_setup = NULL;
parms.neigh_cleanup = NULL;
ret = slave_ops->ndo_neigh_setup(slave->dev, &parms);
if (ret)
return ret;
/*
* Assign slave's neigh_cleanup to neighbour in case cleanup is called
* after the last slave has been detached. Assumes that all slaves
* utilize the same neigh_cleanup (true at this writing as only user
* is ipoib).
*/
n->parms->neigh_cleanup = parms.neigh_cleanup;
if (!parms.neigh_setup)
return 0;
return parms.neigh_setup(n);
}
/*
* The bonding ndo_neigh_setup is called at init time beofre any
* slave exists. So we must declare proxy setup function which will
* be used at run time to resolve the actual slave neigh param setup.
*/
static int bond_neigh_setup(struct net_device *dev,
struct neigh_parms *parms)
{
parms->neigh_setup = bond_neigh_init;
return 0;
}
/*
* Change the MTU of all of a master's slaves to match the master
*/
static int bond_change_mtu(struct net_device *bond_dev, int new_mtu)
{
struct bonding *bond = netdev_priv(bond_dev);
struct slave *slave, *stop_at;
int res = 0;
int i;
pr_debug("bond=%p, name=%s, new_mtu=%d\n", bond,
(bond_dev ? bond_dev->name : "None"), new_mtu);
/* Can't hold bond->lock with bh disabled here since
* some base drivers panic. On the other hand we can't
* hold bond->lock without bh disabled because we'll
* deadlock. The only solution is to rely on the fact
* that we're under rtnl_lock here, and the slaves
* list won't change. This doesn't solve the problem
* of setting the slave's MTU while it is
* transmitting, but the assumption is that the base
* driver can handle that.
*
* TODO: figure out a way to safely iterate the slaves
* list, but without holding a lock around the actual
* call to the base driver.
*/
bond_for_each_slave(bond, slave, i) {
pr_debug("s %p s->p %p c_m %p\n",
slave,
slave->prev,
slave->dev->netdev_ops->ndo_change_mtu);
res = dev_set_mtu(slave->dev, new_mtu);
if (res) {
/* If we failed to set the slave's mtu to the new value
* we must abort the operation even in ACTIVE_BACKUP
* mode, because if we allow the backup slaves to have
* different mtu values than the active slave we'll
* need to change their mtu when doing a failover. That
* means changing their mtu from timer context, which
* is probably not a good idea.
*/
pr_debug("err %d %s\n", res, slave->dev->name);
goto unwind;
}
}
bond_dev->mtu = new_mtu;
return 0;
unwind:
/* unwind from head to the slave that failed */
stop_at = slave;
bond_for_each_slave_from_to(bond, slave, i, bond->first_slave, stop_at) {
int tmp_res;
tmp_res = dev_set_mtu(slave->dev, bond_dev->mtu);
if (tmp_res) {
pr_debug("unwind err %d dev %s\n",
tmp_res, slave->dev->name);
}
}
return res;
}
/*
* Change HW address
*
* Note that many devices must be down to change the HW address, and
* downing the master releases all slaves. We can make bonds full of
* bonding devices to test this, however.
*/
static int bond_set_mac_address(struct net_device *bond_dev, void *addr)
{
struct bonding *bond = netdev_priv(bond_dev);
struct sockaddr *sa = addr, tmp_sa;
struct slave *slave, *stop_at;
int res = 0;
int i;
if (bond->params.mode == BOND_MODE_ALB)
return bond_alb_set_mac_address(bond_dev, addr);
pr_debug("bond=%p, name=%s\n",
bond, bond_dev ? bond_dev->name : "None");
/*
* If fail_over_mac is set to active, do nothing and return
* success. Returning an error causes ifenslave to fail.
*/
if (bond->params.fail_over_mac == BOND_FOM_ACTIVE)
return 0;
if (!is_valid_ether_addr(sa->sa_data))
return -EADDRNOTAVAIL;
/* Can't hold bond->lock with bh disabled here since
* some base drivers panic. On the other hand we can't
* hold bond->lock without bh disabled because we'll
* deadlock. The only solution is to rely on the fact
* that we're under rtnl_lock here, and the slaves
* list won't change. This doesn't solve the problem
* of setting the slave's hw address while it is
* transmitting, but the assumption is that the base
* driver can handle that.
*
* TODO: figure out a way to safely iterate the slaves
* list, but without holding a lock around the actual
* call to the base driver.
*/
bond_for_each_slave(bond, slave, i) {
const struct net_device_ops *slave_ops = slave->dev->netdev_ops;
pr_debug("slave %p %s\n", slave, slave->dev->name);
if (slave_ops->ndo_set_mac_address == NULL) {
res = -EOPNOTSUPP;
pr_debug("EOPNOTSUPP %s\n", slave->dev->name);
goto unwind;
}
res = dev_set_mac_address(slave->dev, addr);
if (res) {
/* TODO: consider downing the slave
* and retry ?
* User should expect communications
* breakage anyway until ARP finish
* updating, so...
*/
pr_debug("err %d %s\n", res, slave->dev->name);
goto unwind;
}
}
/* success */
memcpy(bond_dev->dev_addr, sa->sa_data, bond_dev->addr_len);
return 0;
unwind:
memcpy(tmp_sa.sa_data, bond_dev->dev_addr, bond_dev->addr_len);
tmp_sa.sa_family = bond_dev->type;
/* unwind from head to the slave that failed */
stop_at = slave;
bond_for_each_slave_from_to(bond, slave, i, bond->first_slave, stop_at) {
int tmp_res;
tmp_res = dev_set_mac_address(slave->dev, &tmp_sa);
if (tmp_res) {
pr_debug("unwind err %d dev %s\n",
tmp_res, slave->dev->name);
}
}
return res;
}
static int bond_xmit_roundrobin(struct sk_buff *skb, struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
struct slave *slave, *start_at;
int i, slave_no, res = 1;
struct iphdr *iph = ip_hdr(skb);
/*
* Start with the curr_active_slave that joined the bond as the
* default for sending IGMP traffic. For failover purposes one
* needs to maintain some consistency for the interface that will
* send the join/membership reports. The curr_active_slave found
* will send all of this type of traffic.
*/
if ((iph->protocol == IPPROTO_IGMP) &&
(skb->protocol == htons(ETH_P_IP))) {
read_lock(&bond->curr_slave_lock);
slave = bond->curr_active_slave;
read_unlock(&bond->curr_slave_lock);
if (!slave)
goto out;
} else {
/*
* Concurrent TX may collide on rr_tx_counter; we accept
* that as being rare enough not to justify using an
* atomic op here.
*/
slave_no = bond->rr_tx_counter++ % bond->slave_cnt;
bond_for_each_slave(bond, slave, i) {
slave_no--;
if (slave_no < 0)
break;
}
}
start_at = slave;
bond_for_each_slave_from(bond, slave, i, start_at) {
if (IS_UP(slave->dev) &&
(slave->link == BOND_LINK_UP) &&
bond_is_active_slave(slave)) {
res = bond_dev_queue_xmit(bond, skb, slave->dev);
break;
}
}
out:
if (res) {
/* no suitable interface, frame not sent */
kfree_skb(skb);
}
return NETDEV_TX_OK;
}
/*
* in active-backup mode, we know that bond->curr_active_slave is always valid if
* the bond has a usable interface.
*/
static int bond_xmit_activebackup(struct sk_buff *skb, struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
int res = 1;
read_lock(&bond->curr_slave_lock);
if (bond->curr_active_slave)
res = bond_dev_queue_xmit(bond, skb,
bond->curr_active_slave->dev);
read_unlock(&bond->curr_slave_lock);
if (res)
/* no suitable interface, frame not sent */
kfree_skb(skb);
return NETDEV_TX_OK;
}
/*
* In bond_xmit_xor() , we determine the output device by using a pre-
* determined xmit_hash_policy(), If the selected device is not enabled,
* find the next active slave.
*/
static int bond_xmit_xor(struct sk_buff *skb, struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
struct slave *slave, *start_at;
int slave_no;
int i;
int res = 1;
slave_no = bond->xmit_hash_policy(skb, bond->slave_cnt);
bond_for_each_slave(bond, slave, i) {
slave_no--;
if (slave_no < 0)
break;
}
start_at = slave;
bond_for_each_slave_from(bond, slave, i, start_at) {
if (IS_UP(slave->dev) &&
(slave->link == BOND_LINK_UP) &&
bond_is_active_slave(slave)) {
res = bond_dev_queue_xmit(bond, skb, slave->dev);
break;
}
}
if (res) {
/* no suitable interface, frame not sent */
kfree_skb(skb);
}
return NETDEV_TX_OK;
}
/*
* in broadcast mode, we send everything to all usable interfaces.
*/
static int bond_xmit_broadcast(struct sk_buff *skb, struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
struct slave *slave, *start_at;
struct net_device *tx_dev = NULL;
int i;
int res = 1;
read_lock(&bond->curr_slave_lock);
start_at = bond->curr_active_slave;
read_unlock(&bond->curr_slave_lock);
if (!start_at)
goto out;
bond_for_each_slave_from(bond, slave, i, start_at) {
if (IS_UP(slave->dev) &&
(slave->link == BOND_LINK_UP) &&
bond_is_active_slave(slave)) {
if (tx_dev) {
struct sk_buff *skb2 = skb_clone(skb, GFP_ATOMIC);
if (!skb2) {
pr_err("%s: Error: bond_xmit_broadcast(): skb_clone() failed\n",
bond_dev->name);
continue;
}
res = bond_dev_queue_xmit(bond, skb2, tx_dev);
if (res) {
kfree_skb(skb2);
continue;
}
}
tx_dev = slave->dev;
}
}
if (tx_dev)
res = bond_dev_queue_xmit(bond, skb, tx_dev);
out:
if (res)
/* no suitable interface, frame not sent */
kfree_skb(skb);
/* frame sent to all suitable interfaces */
return NETDEV_TX_OK;
}
/*------------------------- Device initialization ---------------------------*/
static void bond_set_xmit_hash_policy(struct bonding *bond)
{
switch (bond->params.xmit_policy) {
case BOND_XMIT_POLICY_LAYER23:
bond->xmit_hash_policy = bond_xmit_hash_policy_l23;
break;
case BOND_XMIT_POLICY_LAYER34:
bond->xmit_hash_policy = bond_xmit_hash_policy_l34;
break;
case BOND_XMIT_POLICY_LAYER2:
default:
bond->xmit_hash_policy = bond_xmit_hash_policy_l2;
break;
}
}
bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 08:40:18 +00:00
/*
* Lookup the slave that corresponds to a qid
*/
static inline int bond_slave_override(struct bonding *bond,
struct sk_buff *skb)
{
int i, res = 1;
struct slave *slave = NULL;
struct slave *check_slave;
if (!skb->queue_mapping)
return 1;
bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 08:40:18 +00:00
/* Find out if any slaves have the same mapping as this skb. */
bond_for_each_slave(bond, check_slave, i) {
if (check_slave->queue_id == skb->queue_mapping) {
slave = check_slave;
break;
}
}
/* If the slave isn't UP, use default transmit policy. */
if (slave && slave->queue_id && IS_UP(slave->dev) &&
(slave->link == BOND_LINK_UP)) {
res = bond_dev_queue_xmit(bond, skb, slave->dev);
}
return res;
}
bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 08:40:18 +00:00
static u16 bond_select_queue(struct net_device *dev, struct sk_buff *skb)
{
/*
* This helper function exists to help dev_pick_tx get the correct
* destination queue. Using a helper function skips a call to
bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 08:40:18 +00:00
* skb_tx_hash and will put the skbs in the queue we expect on their
* way down to the bonding driver.
*/
u16 txq = skb_rx_queue_recorded(skb) ? skb_get_rx_queue(skb) : 0;
/*
* Save the original txq to restore before passing to the driver
*/
qdisc_skb_cb(skb)->slave_dev_queue_mapping = skb->queue_mapping;
if (unlikely(txq >= dev->real_num_tx_queues)) {
do {
txq -= dev->real_num_tx_queues;
} while (txq >= dev->real_num_tx_queues);
}
return txq;
bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 08:40:18 +00:00
}
static netdev_tx_t __bond_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 08:40:18 +00:00
struct bonding *bond = netdev_priv(dev);
if (TX_QUEUE_OVERRIDE(bond->params.mode)) {
if (!bond_slave_override(bond, skb))
return NETDEV_TX_OK;
}
switch (bond->params.mode) {
case BOND_MODE_ROUNDROBIN:
return bond_xmit_roundrobin(skb, dev);
case BOND_MODE_ACTIVEBACKUP:
return bond_xmit_activebackup(skb, dev);
case BOND_MODE_XOR:
return bond_xmit_xor(skb, dev);
case BOND_MODE_BROADCAST:
return bond_xmit_broadcast(skb, dev);
case BOND_MODE_8023AD:
return bond_3ad_xmit_xor(skb, dev);
case BOND_MODE_ALB:
case BOND_MODE_TLB:
return bond_alb_xmit(skb, dev);
default:
/* Should never happen, mode already checked */
pr_err("%s: Error: Unknown bonding mode %d\n",
dev->name, bond->params.mode);
WARN_ON_ONCE(1);
kfree_skb(skb);
return NETDEV_TX_OK;
}
}
static netdev_tx_t bond_start_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct bonding *bond = netdev_priv(dev);
netdev_tx_t ret = NETDEV_TX_OK;
/*
* If we risk deadlock from transmitting this in the
* netpoll path, tell netpoll to queue the frame for later tx
*/
if (is_netpoll_tx_blocked(dev))
return NETDEV_TX_BUSY;
read_lock(&bond->lock);
if (bond->slave_cnt)
ret = __bond_start_xmit(skb, dev);
else
kfree_skb(skb);
read_unlock(&bond->lock);
return ret;
}
/*
* set bond mode specific net device operations
*/
void bond_set_mode_ops(struct bonding *bond, int mode)
{
struct net_device *bond_dev = bond->dev;
switch (mode) {
case BOND_MODE_ROUNDROBIN:
break;
case BOND_MODE_ACTIVEBACKUP:
break;
case BOND_MODE_XOR:
bond_set_xmit_hash_policy(bond);
break;
case BOND_MODE_BROADCAST:
break;
case BOND_MODE_8023AD:
bond_set_xmit_hash_policy(bond);
break;
case BOND_MODE_ALB:
/* FALLTHRU */
case BOND_MODE_TLB:
break;
default:
/* Should never happen, mode already checked */
pr_err("%s: Error: Unknown bonding mode %d\n",
bond_dev->name, mode);
break;
}
}
static void bond_ethtool_get_drvinfo(struct net_device *bond_dev,
struct ethtool_drvinfo *drvinfo)
{
strncpy(drvinfo->driver, DRV_NAME, 32);
strncpy(drvinfo->version, DRV_VERSION, 32);
snprintf(drvinfo->fw_version, 32, "%d", BOND_ABI_VERSION);
}
static const struct ethtool_ops bond_ethtool_ops = {
.get_drvinfo = bond_ethtool_get_drvinfo,
.get_link = ethtool_op_get_link,
};
static const struct net_device_ops bond_netdev_ops = {
.ndo_init = bond_init,
.ndo_uninit = bond_uninit,
.ndo_open = bond_open,
.ndo_stop = bond_close,
.ndo_start_xmit = bond_start_xmit,
bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 08:40:18 +00:00
.ndo_select_queue = bond_select_queue,
.ndo_get_stats64 = bond_get_stats,
.ndo_do_ioctl = bond_do_ioctl,
.ndo_change_rx_flags = bond_change_rx_flags,
.ndo_set_rx_mode = bond_set_multicast_list,
.ndo_change_mtu = bond_change_mtu,
.ndo_set_mac_address = bond_set_mac_address,
.ndo_neigh_setup = bond_neigh_setup,
.ndo_vlan_rx_add_vid = bond_vlan_rx_add_vid,
.ndo_vlan_rx_kill_vid = bond_vlan_rx_kill_vid,
#ifdef CONFIG_NET_POLL_CONTROLLER
.ndo_netpoll_setup = bond_netpoll_setup,
.ndo_netpoll_cleanup = bond_netpoll_cleanup,
.ndo_poll_controller = bond_poll_controller,
#endif
.ndo_add_slave = bond_enslave,
.ndo_del_slave = bond_release,
.ndo_fix_features = bond_fix_features,
};
static void bond_destructor(struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
if (bond->wq)
destroy_workqueue(bond->wq);
free_netdev(bond_dev);
}
static void bond_setup(struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
/* initialize rwlocks */
rwlock_init(&bond->lock);
rwlock_init(&bond->curr_slave_lock);
bond->params = bonding_defaults;
/* Initialize pointers */
bond->dev = bond_dev;
INIT_LIST_HEAD(&bond->vlan_list);
/* Initialize the device entry points */
ether_setup(bond_dev);
bond_dev->netdev_ops = &bond_netdev_ops;
bond_dev->ethtool_ops = &bond_ethtool_ops;
bond_set_mode_ops(bond, bond->params.mode);
bond_dev->destructor = bond_destructor;
/* Initialize the device options */
bond_dev->tx_queue_len = 0;
bond_dev->flags |= IFF_MASTER|IFF_MULTICAST;
bond_dev->priv_flags |= IFF_BONDING;
bond_dev->priv_flags &= ~(IFF_XMIT_DST_RELEASE | IFF_TX_SKB_SHARING);
/* At first, we block adding VLANs. That's the only way to
* prevent problems that occur when adding VLANs over an
* empty bond. The block will be removed once non-challenged
* slaves are enslaved.
*/
bond_dev->features |= NETIF_F_VLAN_CHALLENGED;
[NET]: Add netif_tx_lock Various drivers use xmit_lock internally to synchronise with their transmission routines. They do so without setting xmit_lock_owner. This is fine as long as netpoll is not in use. With netpoll it is possible for deadlocks to occur if xmit_lock_owner isn't set. This is because if a printk occurs while xmit_lock is held and xmit_lock_owner is not set can cause netpoll to attempt to take xmit_lock recursively. While it is possible to resolve this by getting netpoll to use trylock, it is suboptimal because netpoll's sole objective is to maximise the chance of getting the printk out on the wire. So delaying or dropping the message is to be avoided as much as possible. So the only alternative is to always set xmit_lock_owner. The following patch does this by introducing the netif_tx_lock family of functions that take care of setting/unsetting xmit_lock_owner. I renamed xmit_lock to _xmit_lock to indicate that it should not be used directly. I didn't provide irq versions of the netif_tx_lock functions since xmit_lock is meant to be a BH-disabling lock. This is pretty much a straight text substitution except for a small bug fix in winbond. It currently uses netif_stop_queue/spin_unlock_wait to stop transmission. This is unsafe as an IRQ can potentially wake up the queue. So it is safer to use netif_tx_disable. The hamradio bits used spin_lock_irq but it is unnecessary as xmit_lock must never be taken in an IRQ handler. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2006-06-09 19:20:56 +00:00
/* don't acquire bond device's netif_tx_lock when
* transmitting */
bond_dev->features |= NETIF_F_LLTX;
/* By default, we declare the bond to be fully
* VLAN hardware accelerated capable. Special
* care is taken in the various xmit functions
* when there are slaves that are not hw accel
* capable
*/
bond_dev->hw_features = BOND_VLAN_FEATURES |
NETIF_F_HW_VLAN_TX |
NETIF_F_HW_VLAN_RX |
NETIF_F_HW_VLAN_FILTER;
bond_dev->hw_features &= ~(NETIF_F_ALL_CSUM & ~NETIF_F_HW_CSUM);
bond_dev->features |= bond_dev->hw_features;
}
static void bond_work_cancel_all(struct bonding *bond)
{
if (bond->params.miimon && delayed_work_pending(&bond->mii_work))
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
cancel_delayed_work_sync(&bond->mii_work);
if (bond->params.arp_interval && delayed_work_pending(&bond->arp_work))
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
cancel_delayed_work_sync(&bond->arp_work);
if (bond->params.mode == BOND_MODE_ALB &&
delayed_work_pending(&bond->alb_work))
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
cancel_delayed_work_sync(&bond->alb_work);
if (bond->params.mode == BOND_MODE_8023AD &&
delayed_work_pending(&bond->ad_work))
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
cancel_delayed_work_sync(&bond->ad_work);
if (delayed_work_pending(&bond->mcast_work))
bonding: eliminate bond_close race conditions This patch resolves two sets of race conditions. Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> reported the first, as follows: The bond_close() calls cancel_delayed_work() to cancel delayed works. It, however, cannot cancel works that were already queued in workqueue. The bond_open() initializes work->data, and proccess_one_work() refers get_work_cwq(work)->wq->flags. The get_work_cwq() returns NULL when work->data has been initialized. Thus, a panic occurs. He included a patch that converted the cancel_delayed_work calls in bond_close to flush_delayed_work_sync, which eliminated the above problem. His patch is incorporated, at least in principle, into this patch. In this patch, we use cancel_delayed_work_sync in place of flush_delayed_work_sync, and also convert bond_uninit in addition to bond_close. This conversion to _sync, however, opens new races between bond_close and three periodically executing workqueue functions: bond_mii_monitor, bond_alb_monitor and bond_activebackup_arp_mon. The race occurs because bond_close and bond_uninit are always called with RTNL held, and these workqueue functions may acquire RTNL to perform failover-related activities. If bond_close or bond_uninit is waiting in cancel_delayed_work_sync, deadlock occurs. These deadlocks are resolved by having the workqueue functions acquire RTNL conditionally. If the rtnl_trylock() fails, the functions reschedule and return immediately. For the cases that are attempting to perform link failover, a delay of 1 is used; for the other cases, the normal interval is used (as those activities are not as time critical). Additionally, the bond_mii_monitor function now stores the delay in a variable (mimicing the structure of activebackup_arp_mon). Lastly, all of the above renders the kill_timers sentinel moot, and therefore it has been removed. Tested-by: Mitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-28 15:42:50 +00:00
cancel_delayed_work_sync(&bond->mcast_work);
}
/*
* Destroy a bonding device.
* Must be under rtnl_lock when this function is called.
*/
static void bond_uninit(struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
struct vlan_entry *vlan, *tmp;
bond_netpoll_cleanup(bond_dev);
/* Release the bonded slaves */
bond_release_all(bond_dev);
list_del(&bond->bond_list);
bond_work_cancel_all(bond);
bond_debug_unregister(bond);
__hw_addr_flush(&bond->mc_list);
list_for_each_entry_safe(vlan, tmp, &bond->vlan_list, vlan_list) {
list_del(&vlan->vlan_list);
kfree(vlan);
}
}
/*------------------------- Module initialization ---------------------------*/
/*
* Convert string input module parms. Accept either the
* number of the mode or its string name. A bit complicated because
* some mode names are substrings of other names, and calls from sysfs
* may have whitespace in the name (trailing newlines, for example).
*/
int bond_parse_parm(const char *buf, const struct bond_parm_tbl *tbl)
{
int modeint = -1, i, rv;
char *p, modestr[BOND_MAX_MODENAME_LEN + 1] = { 0, };
for (p = (char *)buf; *p; p++)
if (!(isdigit(*p) || isspace(*p)))
break;
if (*p)
rv = sscanf(buf, "%20s", modestr);
else
rv = sscanf(buf, "%d", &modeint);
if (!rv)
return -1;
for (i = 0; tbl[i].modename; i++) {
if (modeint == tbl[i].mode)
return tbl[i].mode;
if (strcmp(modestr, tbl[i].modename) == 0)
return tbl[i].mode;
}
return -1;
}
static int bond_check_params(struct bond_params *params)
{
int arp_validate_value, fail_over_mac_value, primary_reselect_value;
/*
* Convert string parameters.
*/
if (mode) {
bond_mode = bond_parse_parm(mode, bond_mode_tbl);
if (bond_mode == -1) {
pr_err("Error: Invalid bonding mode \"%s\"\n",
mode == NULL ? "NULL" : mode);
return -EINVAL;
}
}
if (xmit_hash_policy) {
if ((bond_mode != BOND_MODE_XOR) &&
(bond_mode != BOND_MODE_8023AD)) {
pr_info("xmit_hash_policy param is irrelevant in mode %s\n",
bond_mode_name(bond_mode));
} else {
xmit_hashtype = bond_parse_parm(xmit_hash_policy,
xmit_hashtype_tbl);
if (xmit_hashtype == -1) {
pr_err("Error: Invalid xmit_hash_policy \"%s\"\n",
xmit_hash_policy == NULL ? "NULL" :
xmit_hash_policy);
return -EINVAL;
}
}
}
if (lacp_rate) {
if (bond_mode != BOND_MODE_8023AD) {
pr_info("lacp_rate param is irrelevant in mode %s\n",
bond_mode_name(bond_mode));
} else {
lacp_fast = bond_parse_parm(lacp_rate, bond_lacp_tbl);
if (lacp_fast == -1) {
pr_err("Error: Invalid lacp rate \"%s\"\n",
lacp_rate == NULL ? "NULL" : lacp_rate);
return -EINVAL;
}
}
}
if (ad_select) {
params->ad_select = bond_parse_parm(ad_select, ad_select_tbl);
if (params->ad_select == -1) {
pr_err("Error: Invalid ad_select \"%s\"\n",
ad_select == NULL ? "NULL" : ad_select);
return -EINVAL;
}
if (bond_mode != BOND_MODE_8023AD) {
pr_warning("ad_select param only affects 802.3ad mode\n");
}
} else {
params->ad_select = BOND_AD_STABLE;
}
if (max_bonds < 0) {
pr_warning("Warning: max_bonds (%d) not in range %d-%d, so it was reset to BOND_DEFAULT_MAX_BONDS (%d)\n",
max_bonds, 0, INT_MAX, BOND_DEFAULT_MAX_BONDS);
max_bonds = BOND_DEFAULT_MAX_BONDS;
}
if (miimon < 0) {
pr_warning("Warning: miimon module parameter (%d), not in range 0-%d, so it was reset to %d\n",
miimon, INT_MAX, BOND_LINK_MON_INTERV);
miimon = BOND_LINK_MON_INTERV;
}
if (updelay < 0) {
pr_warning("Warning: updelay module parameter (%d), not in range 0-%d, so it was reset to 0\n",
updelay, INT_MAX);
updelay = 0;
}
if (downdelay < 0) {
pr_warning("Warning: downdelay module parameter (%d), not in range 0-%d, so it was reset to 0\n",
downdelay, INT_MAX);
downdelay = 0;
}
if ((use_carrier != 0) && (use_carrier != 1)) {
pr_warning("Warning: use_carrier module parameter (%d), not of valid value (0/1), so it was set to 1\n",
use_carrier);
use_carrier = 1;
}
if (num_peer_notif < 0 || num_peer_notif > 255) {
pr_warning("Warning: num_grat_arp/num_unsol_na (%d) not in range 0-255 so it was reset to 1\n",
num_peer_notif);
num_peer_notif = 1;
}
/* reset values for 802.3ad */
if (bond_mode == BOND_MODE_8023AD) {
if (!miimon) {
pr_warning("Warning: miimon must be specified, otherwise bonding will not detect link failure, speed and duplex which are essential for 802.3ad operation\n");
pr_warning("Forcing miimon to 100msec\n");
miimon = 100;
}
}
bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 08:40:18 +00:00
if (tx_queues < 1 || tx_queues > 255) {
pr_warning("Warning: tx_queues (%d) should be between "
"1 and 255, resetting to %d\n",
tx_queues, BOND_DEFAULT_TX_QUEUES);
tx_queues = BOND_DEFAULT_TX_QUEUES;
}
if ((all_slaves_active != 0) && (all_slaves_active != 1)) {
pr_warning("Warning: all_slaves_active module parameter (%d), "
"not of valid value (0/1), so it was set to "
"0\n", all_slaves_active);
all_slaves_active = 0;
}
if (resend_igmp < 0 || resend_igmp > 255) {
pr_warning("Warning: resend_igmp (%d) should be between "
"0 and 255, resetting to %d\n",
resend_igmp, BOND_DEFAULT_RESEND_IGMP);
resend_igmp = BOND_DEFAULT_RESEND_IGMP;
}
/* reset values for TLB/ALB */
if ((bond_mode == BOND_MODE_TLB) ||
(bond_mode == BOND_MODE_ALB)) {
if (!miimon) {
pr_warning("Warning: miimon must be specified, otherwise bonding will not detect link failure and link speed which are essential for TLB/ALB load balancing\n");
pr_warning("Forcing miimon to 100msec\n");
miimon = 100;
}
}
if (bond_mode == BOND_MODE_ALB) {
pr_notice("In ALB mode you might experience client disconnections upon reconnection of a link if the bonding module updelay parameter (%d msec) is incompatible with the forwarding delay time of the switch\n",
updelay);
}
if (!miimon) {
if (updelay || downdelay) {
/* just warn the user the up/down delay will have
* no effect since miimon is zero...
*/
pr_warning("Warning: miimon module parameter not set and updelay (%d) or downdelay (%d) module parameter is set; updelay and downdelay have no effect unless miimon is set\n",
updelay, downdelay);
}
} else {
/* don't allow arp monitoring */
if (arp_interval) {
pr_warning("Warning: miimon (%d) and arp_interval (%d) can't be used simultaneously, disabling ARP monitoring\n",
miimon, arp_interval);
arp_interval = 0;
}
if ((updelay % miimon) != 0) {
pr_warning("Warning: updelay (%d) is not a multiple of miimon (%d), updelay rounded to %d ms\n",
updelay, miimon,
(updelay / miimon) * miimon);
}
updelay /= miimon;
if ((downdelay % miimon) != 0) {
pr_warning("Warning: downdelay (%d) is not a multiple of miimon (%d), downdelay rounded to %d ms\n",
downdelay, miimon,
(downdelay / miimon) * miimon);
}
downdelay /= miimon;
}
if (arp_interval < 0) {
pr_warning("Warning: arp_interval module parameter (%d) , not in range 0-%d, so it was reset to %d\n",
arp_interval, INT_MAX, BOND_LINK_ARP_INTERV);
arp_interval = BOND_LINK_ARP_INTERV;
}
for (arp_ip_count = 0;
(arp_ip_count < BOND_MAX_ARP_TARGETS) && arp_ip_target[arp_ip_count];
arp_ip_count++) {
/* not complete check, but should be good enough to
catch mistakes */
if (!isdigit(arp_ip_target[arp_ip_count][0])) {
pr_warning("Warning: bad arp_ip_target module parameter (%s), ARP monitoring will not be performed\n",
arp_ip_target[arp_ip_count]);
arp_interval = 0;
} else {
__be32 ip = in_aton(arp_ip_target[arp_ip_count]);
arp_target[arp_ip_count] = ip;
}
}
if (arp_interval && !arp_ip_count) {
/* don't allow arping if no arp_ip_target given... */
pr_warning("Warning: arp_interval module parameter (%d) specified without providing an arp_ip_target parameter, arp_interval was reset to 0\n",
arp_interval);
arp_interval = 0;
}
if (arp_validate) {
if (bond_mode != BOND_MODE_ACTIVEBACKUP) {
pr_err("arp_validate only supported in active-backup mode\n");
return -EINVAL;
}
if (!arp_interval) {
pr_err("arp_validate requires arp_interval\n");
return -EINVAL;
}
arp_validate_value = bond_parse_parm(arp_validate,
arp_validate_tbl);
if (arp_validate_value == -1) {
pr_err("Error: invalid arp_validate \"%s\"\n",
arp_validate == NULL ? "NULL" : arp_validate);
return -EINVAL;
}
} else
arp_validate_value = 0;
if (miimon) {
pr_info("MII link monitoring set to %d ms\n", miimon);
} else if (arp_interval) {
int i;
pr_info("ARP monitoring set to %d ms, validate %s, with %d target(s):",
arp_interval,
arp_validate_tbl[arp_validate_value].modename,
arp_ip_count);
for (i = 0; i < arp_ip_count; i++)
pr_info(" %s", arp_ip_target[i]);
pr_info("\n");
} else if (max_bonds) {
/* miimon and arp_interval not set, we need one so things
* work as expected, see bonding.txt for details
*/
pr_debug("Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.\n");
}
if (primary && !USES_PRIMARY(bond_mode)) {
/* currently, using a primary only makes sense
* in active backup, TLB or ALB modes
*/
pr_warning("Warning: %s primary device specified but has no effect in %s mode\n",
primary, bond_mode_name(bond_mode));
primary = NULL;
}
if (primary && primary_reselect) {
primary_reselect_value = bond_parse_parm(primary_reselect,
pri_reselect_tbl);
if (primary_reselect_value == -1) {
pr_err("Error: Invalid primary_reselect \"%s\"\n",
primary_reselect ==
NULL ? "NULL" : primary_reselect);
return -EINVAL;
}
} else {
primary_reselect_value = BOND_PRI_RESELECT_ALWAYS;
}
if (fail_over_mac) {
fail_over_mac_value = bond_parse_parm(fail_over_mac,
fail_over_mac_tbl);
if (fail_over_mac_value == -1) {
pr_err("Error: invalid fail_over_mac \"%s\"\n",
arp_validate == NULL ? "NULL" : arp_validate);
return -EINVAL;
}
if (bond_mode != BOND_MODE_ACTIVEBACKUP)
pr_warning("Warning: fail_over_mac only affects active-backup mode.\n");
} else {
fail_over_mac_value = BOND_FOM_NONE;
}
/* fill params struct with the proper values */
params->mode = bond_mode;
params->xmit_policy = xmit_hashtype;
params->miimon = miimon;
params->num_peer_notif = num_peer_notif;
params->arp_interval = arp_interval;
params->arp_validate = arp_validate_value;
params->updelay = updelay;
params->downdelay = downdelay;
params->use_carrier = use_carrier;
params->lacp_fast = lacp_fast;
params->primary[0] = 0;
params->primary_reselect = primary_reselect_value;
params->fail_over_mac = fail_over_mac_value;
bonding: allow user-controlled output slave selection v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-02 08:40:18 +00:00
params->tx_queues = tx_queues;
params->all_slaves_active = all_slaves_active;
params->resend_igmp = resend_igmp;
params->min_links = min_links;
if (primary) {
strncpy(params->primary, primary, IFNAMSIZ);
params->primary[IFNAMSIZ - 1] = 0;
}
memcpy(params->arp_targets, arp_target, sizeof(arp_target));
return 0;
}
static struct lock_class_key bonding_netdev_xmit_lock_key;
static struct lock_class_key bonding_netdev_addr_lock_key;
bonding: set qdisc_tx_busylock to avoid LOCKDEP splat If a qdisc is installed on a bonding device, its possible to get following lockdep splat under stress : ============================================= [ INFO: possible recursive locking detected ] 3.6.0+ #211 Not tainted --------------------------------------------- ping/4876 is trying to acquire lock: (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+.-...}, at: [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830 but task is already holding lock: (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+.-...}, at: [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(dev->qdisc_tx_busylock ?: &qdisc_tx_busylock); lock(dev->qdisc_tx_busylock ?: &qdisc_tx_busylock); *** DEADLOCK *** May be due to missing lock nesting notation 6 locks held by ping/4876: #0: (sk_lock-AF_INET){+.+.+.}, at: [<ffffffff815e5030>] raw_sendmsg+0x600/0xc30 #1: (rcu_read_lock_bh){.+....}, at: [<ffffffff815ba4bd>] ip_finish_output+0x12d/0x870 #2: (rcu_read_lock_bh){.+....}, at: [<ffffffff8157a0b0>] dev_queue_xmit+0x0/0x830 #3: (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+.-...}, at: [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830 #4: (&bond->lock){++.?..}, at: [<ffffffffa02128c1>] bond_start_xmit+0x31/0x4b0 [bonding] #5: (rcu_read_lock_bh){.+....}, at: [<ffffffff8157a0b0>] dev_queue_xmit+0x0/0x830 stack backtrace: Pid: 4876, comm: ping Not tainted 3.6.0+ #211 Call Trace: [<ffffffff810a0145>] __lock_acquire+0x715/0x1b80 [<ffffffff810a256b>] ? mark_held_locks+0x9b/0x100 [<ffffffff810a1bf2>] lock_acquire+0x92/0x1d0 [<ffffffff8157a191>] ? dev_queue_xmit+0xe1/0x830 [<ffffffff81726b7c>] _raw_spin_lock+0x3c/0x50 [<ffffffff8157a191>] ? dev_queue_xmit+0xe1/0x830 [<ffffffff8106264d>] ? rcu_read_lock_bh_held+0x5d/0x90 [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830 [<ffffffff8157a0b0>] ? netdev_pick_tx+0x570/0x570 [<ffffffffa0212a6a>] bond_start_xmit+0x1da/0x4b0 [bonding] [<ffffffff815796d0>] dev_hard_start_xmit+0x240/0x6b0 [<ffffffff81597c6e>] sch_direct_xmit+0xfe/0x2a0 [<ffffffff8157a249>] dev_queue_xmit+0x199/0x830 [<ffffffff8157a0b0>] ? netdev_pick_tx+0x570/0x570 [<ffffffff815ba96f>] ip_finish_output+0x5df/0x870 [<ffffffff815ba4bd>] ? ip_finish_output+0x12d/0x870 [<ffffffff815bb964>] ip_output+0x54/0xf0 [<ffffffff815bad48>] ip_local_out+0x28/0x90 [<ffffffff815bc444>] ip_send_skb+0x14/0x50 [<ffffffff815bc4b2>] ip_push_pending_frames+0x32/0x40 [<ffffffff815e536a>] raw_sendmsg+0x93a/0xc30 [<ffffffff8128d570>] ? selinux_file_send_sigiotask+0x1f0/0x1f0 [<ffffffff8109ddb4>] ? __lock_is_held+0x54/0x80 [<ffffffff815f6730>] ? inet_recvmsg+0x220/0x220 [<ffffffff8109ddb4>] ? __lock_is_held+0x54/0x80 [<ffffffff815f6855>] inet_sendmsg+0x125/0x240 [<ffffffff815f6730>] ? inet_recvmsg+0x220/0x220 [<ffffffff8155cddb>] sock_sendmsg+0xab/0xe0 [<ffffffff810a1650>] ? lock_release_non_nested+0xa0/0x2e0 [<ffffffff810a1650>] ? lock_release_non_nested+0xa0/0x2e0 [<ffffffff8155d18c>] __sys_sendmsg+0x37c/0x390 [<ffffffff81195b2a>] ? fsnotify+0x2ca/0x7e0 [<ffffffff811958e8>] ? fsnotify+0x88/0x7e0 [<ffffffff81361f36>] ? put_ldisc+0x56/0xd0 [<ffffffff8116f98a>] ? fget_light+0x3da/0x510 [<ffffffff8155f6c4>] sys_sendmsg+0x44/0x80 [<ffffffff8172fc22>] system_call_fastpath+0x16/0x1b Avoid this problem using a distinct lock_class_key for bonding devices. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jay Vosburgh <fubar@us.ibm.com> Cc: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-03 23:05:26 +00:00
static struct lock_class_key bonding_tx_busylock_key;
static void bond_set_lockdep_class_one(struct net_device *dev,
struct netdev_queue *txq,
void *_unused)
{
lockdep_set_class(&txq->_xmit_lock,
&bonding_netdev_xmit_lock_key);
}
static void bond_set_lockdep_class(struct net_device *dev)
{
lockdep_set_class(&dev->addr_list_lock,
&bonding_netdev_addr_lock_key);
netdev_for_each_tx_queue(dev, bond_set_lockdep_class_one, NULL);
bonding: set qdisc_tx_busylock to avoid LOCKDEP splat If a qdisc is installed on a bonding device, its possible to get following lockdep splat under stress : ============================================= [ INFO: possible recursive locking detected ] 3.6.0+ #211 Not tainted --------------------------------------------- ping/4876 is trying to acquire lock: (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+.-...}, at: [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830 but task is already holding lock: (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+.-...}, at: [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(dev->qdisc_tx_busylock ?: &qdisc_tx_busylock); lock(dev->qdisc_tx_busylock ?: &qdisc_tx_busylock); *** DEADLOCK *** May be due to missing lock nesting notation 6 locks held by ping/4876: #0: (sk_lock-AF_INET){+.+.+.}, at: [<ffffffff815e5030>] raw_sendmsg+0x600/0xc30 #1: (rcu_read_lock_bh){.+....}, at: [<ffffffff815ba4bd>] ip_finish_output+0x12d/0x870 #2: (rcu_read_lock_bh){.+....}, at: [<ffffffff8157a0b0>] dev_queue_xmit+0x0/0x830 #3: (dev->qdisc_tx_busylock ?: &qdisc_tx_busylock){+.-...}, at: [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830 #4: (&bond->lock){++.?..}, at: [<ffffffffa02128c1>] bond_start_xmit+0x31/0x4b0 [bonding] #5: (rcu_read_lock_bh){.+....}, at: [<ffffffff8157a0b0>] dev_queue_xmit+0x0/0x830 stack backtrace: Pid: 4876, comm: ping Not tainted 3.6.0+ #211 Call Trace: [<ffffffff810a0145>] __lock_acquire+0x715/0x1b80 [<ffffffff810a256b>] ? mark_held_locks+0x9b/0x100 [<ffffffff810a1bf2>] lock_acquire+0x92/0x1d0 [<ffffffff8157a191>] ? dev_queue_xmit+0xe1/0x830 [<ffffffff81726b7c>] _raw_spin_lock+0x3c/0x50 [<ffffffff8157a191>] ? dev_queue_xmit+0xe1/0x830 [<ffffffff8106264d>] ? rcu_read_lock_bh_held+0x5d/0x90 [<ffffffff8157a191>] dev_queue_xmit+0xe1/0x830 [<ffffffff8157a0b0>] ? netdev_pick_tx+0x570/0x570 [<ffffffffa0212a6a>] bond_start_xmit+0x1da/0x4b0 [bonding] [<ffffffff815796d0>] dev_hard_start_xmit+0x240/0x6b0 [<ffffffff81597c6e>] sch_direct_xmit+0xfe/0x2a0 [<ffffffff8157a249>] dev_queue_xmit+0x199/0x830 [<ffffffff8157a0b0>] ? netdev_pick_tx+0x570/0x570 [<ffffffff815ba96f>] ip_finish_output+0x5df/0x870 [<ffffffff815ba4bd>] ? ip_finish_output+0x12d/0x870 [<ffffffff815bb964>] ip_output+0x54/0xf0 [<ffffffff815bad48>] ip_local_out+0x28/0x90 [<ffffffff815bc444>] ip_send_skb+0x14/0x50 [<ffffffff815bc4b2>] ip_push_pending_frames+0x32/0x40 [<ffffffff815e536a>] raw_sendmsg+0x93a/0xc30 [<ffffffff8128d570>] ? selinux_file_send_sigiotask+0x1f0/0x1f0 [<ffffffff8109ddb4>] ? __lock_is_held+0x54/0x80 [<ffffffff815f6730>] ? inet_recvmsg+0x220/0x220 [<ffffffff8109ddb4>] ? __lock_is_held+0x54/0x80 [<ffffffff815f6855>] inet_sendmsg+0x125/0x240 [<ffffffff815f6730>] ? inet_recvmsg+0x220/0x220 [<ffffffff8155cddb>] sock_sendmsg+0xab/0xe0 [<ffffffff810a1650>] ? lock_release_non_nested+0xa0/0x2e0 [<ffffffff810a1650>] ? lock_release_non_nested+0xa0/0x2e0 [<ffffffff8155d18c>] __sys_sendmsg+0x37c/0x390 [<ffffffff81195b2a>] ? fsnotify+0x2ca/0x7e0 [<ffffffff811958e8>] ? fsnotify+0x88/0x7e0 [<ffffffff81361f36>] ? put_ldisc+0x56/0xd0 [<ffffffff8116f98a>] ? fget_light+0x3da/0x510 [<ffffffff8155f6c4>] sys_sendmsg+0x44/0x80 [<ffffffff8172fc22>] system_call_fastpath+0x16/0x1b Avoid this problem using a distinct lock_class_key for bonding devices. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jay Vosburgh <fubar@us.ibm.com> Cc: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-10-03 23:05:26 +00:00
dev->qdisc_tx_busylock = &bonding_tx_busylock_key;
}
/*
* Called from registration process
*/
static int bond_init(struct net_device *bond_dev)
{
struct bonding *bond = netdev_priv(bond_dev);
struct bond_net *bn = net_generic(dev_net(bond_dev), bond_net_id);
bonding: prevent deadlock on slave store with alb mode (v3) This soft lockup was recently reported: [root@dell-per715-01 ~]# echo +bond5 > /sys/class/net/bonding_masters [root@dell-per715-01 ~]# echo +eth1 > /sys/class/net/bond5/bonding/slaves bonding: bond5: doing slave updates when interface is down. bonding bond5: master_dev is not up in bond_enslave [root@dell-per715-01 ~]# echo -eth1 > /sys/class/net/bond5/bonding/slaves bonding: bond5: doing slave updates when interface is down. BUG: soft lockup - CPU#12 stuck for 60s! [bash:6444] CPU 12: Modules linked in: bonding autofs4 hidp rfcomm l2cap bluetooth lockd sunrpc be2d Pid: 6444, comm: bash Not tainted 2.6.18-262.el5 #1 RIP: 0010:[<ffffffff80064bf0>] [<ffffffff80064bf0>] .text.lock.spinlock+0x26/00 RSP: 0018:ffff810113167da8 EFLAGS: 00000286 RAX: ffff810113167fd8 RBX: ffff810123a47800 RCX: 0000000000ff1025 RDX: 0000000000000000 RSI: ffff810123a47800 RDI: ffff81021b57f6f8 RBP: ffff81021b57f500 R08: 0000000000000000 R09: 000000000000000c R10: 00000000ffffffff R11: ffff81011d41c000 R12: ffff81021b57f000 R13: 0000000000000000 R14: 0000000000000282 R15: 0000000000000282 FS: 00002b3b41ef3f50(0000) GS:ffff810123b27940(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00002b3b456dd000 CR3: 000000031fc60000 CR4: 00000000000006e0 Call Trace: [<ffffffff80064af9>] _spin_lock_bh+0x9/0x14 [<ffffffff886937d7>] :bonding:tlb_clear_slave+0x22/0xa1 [<ffffffff8869423c>] :bonding:bond_alb_deinit_slave+0xba/0xf0 [<ffffffff8868dda6>] :bonding:bond_release+0x1b4/0x450 [<ffffffff8006457b>] __down_write_nested+0x12/0x92 [<ffffffff88696ae4>] :bonding:bonding_store_slaves+0x25c/0x2f7 [<ffffffff801106f7>] sysfs_write_file+0xb9/0xe8 [<ffffffff80016b87>] vfs_write+0xce/0x174 [<ffffffff80017450>] sys_write+0x45/0x6e [<ffffffff8005d28d>] tracesys+0xd5/0xe0 It occurs because we are able to change the slave configuarion of a bond while the bond interface is down. The bonding driver initializes some data structures only after its ndo_open routine is called. Among them is the initalization of the alb tx and rx hash locks. So if we add or remove a slave without first opening the bond master device, we run the risk of trying to lock/unlock a spinlock that has garbage for data in it, which results in our above softlock. Note that sometimes this works, because in many cases an unlocked spinlock has the raw_lock parameter initialized to zero (meaning that the kzalloc of the net_device private data is equivalent to calling spin_lock_init), but thats not true in all cases, and we aren't guaranteed that condition, so we need to pass the relevant spinlocks through the spin_lock_init function. Fix it by moving the spin_lock_init calls for the tx and rx hashtable locks to the ndo_init path, so they are ready for use by the bond_store_slaves path. Change notes: v2) Based on conversation with Jay and Nicolas it seems that the ability to enslave devices while the bond master is down should be safe to do. As such this is an outlier bug, and so instead we'll just initalize the errant spinlocks in the init path rather than the open path, solving the problem. We'll also remove the warnings about the bond being down during enslave operations, since it should be safe v3) Fix spelling error Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: jtluka@redhat.com CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: nicolas.2p.debian@gmail.com CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-25 08:13:01 +00:00
struct alb_bond_info *bond_info = &(BOND_ALB_INFO(bond));
pr_debug("Begin bond_init for %s\n", bond_dev->name);
bonding: prevent deadlock on slave store with alb mode (v3) This soft lockup was recently reported: [root@dell-per715-01 ~]# echo +bond5 > /sys/class/net/bonding_masters [root@dell-per715-01 ~]# echo +eth1 > /sys/class/net/bond5/bonding/slaves bonding: bond5: doing slave updates when interface is down. bonding bond5: master_dev is not up in bond_enslave [root@dell-per715-01 ~]# echo -eth1 > /sys/class/net/bond5/bonding/slaves bonding: bond5: doing slave updates when interface is down. BUG: soft lockup - CPU#12 stuck for 60s! [bash:6444] CPU 12: Modules linked in: bonding autofs4 hidp rfcomm l2cap bluetooth lockd sunrpc be2d Pid: 6444, comm: bash Not tainted 2.6.18-262.el5 #1 RIP: 0010:[<ffffffff80064bf0>] [<ffffffff80064bf0>] .text.lock.spinlock+0x26/00 RSP: 0018:ffff810113167da8 EFLAGS: 00000286 RAX: ffff810113167fd8 RBX: ffff810123a47800 RCX: 0000000000ff1025 RDX: 0000000000000000 RSI: ffff810123a47800 RDI: ffff81021b57f6f8 RBP: ffff81021b57f500 R08: 0000000000000000 R09: 000000000000000c R10: 00000000ffffffff R11: ffff81011d41c000 R12: ffff81021b57f000 R13: 0000000000000000 R14: 0000000000000282 R15: 0000000000000282 FS: 00002b3b41ef3f50(0000) GS:ffff810123b27940(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00002b3b456dd000 CR3: 000000031fc60000 CR4: 00000000000006e0 Call Trace: [<ffffffff80064af9>] _spin_lock_bh+0x9/0x14 [<ffffffff886937d7>] :bonding:tlb_clear_slave+0x22/0xa1 [<ffffffff8869423c>] :bonding:bond_alb_deinit_slave+0xba/0xf0 [<ffffffff8868dda6>] :bonding:bond_release+0x1b4/0x450 [<ffffffff8006457b>] __down_write_nested+0x12/0x92 [<ffffffff88696ae4>] :bonding:bonding_store_slaves+0x25c/0x2f7 [<ffffffff801106f7>] sysfs_write_file+0xb9/0xe8 [<ffffffff80016b87>] vfs_write+0xce/0x174 [<ffffffff80017450>] sys_write+0x45/0x6e [<ffffffff8005d28d>] tracesys+0xd5/0xe0 It occurs because we are able to change the slave configuarion of a bond while the bond interface is down. The bonding driver initializes some data structures only after its ndo_open routine is called. Among them is the initalization of the alb tx and rx hash locks. So if we add or remove a slave without first opening the bond master device, we run the risk of trying to lock/unlock a spinlock that has garbage for data in it, which results in our above softlock. Note that sometimes this works, because in many cases an unlocked spinlock has the raw_lock parameter initialized to zero (meaning that the kzalloc of the net_device private data is equivalent to calling spin_lock_init), but thats not true in all cases, and we aren't guaranteed that condition, so we need to pass the relevant spinlocks through the spin_lock_init function. Fix it by moving the spin_lock_init calls for the tx and rx hashtable locks to the ndo_init path, so they are ready for use by the bond_store_slaves path. Change notes: v2) Based on conversation with Jay and Nicolas it seems that the ability to enslave devices while the bond master is down should be safe to do. As such this is an outlier bug, and so instead we'll just initalize the errant spinlocks in the init path rather than the open path, solving the problem. We'll also remove the warnings about the bond being down during enslave operations, since it should be safe v3) Fix spelling error Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: jtluka@redhat.com CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: nicolas.2p.debian@gmail.com CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-05-25 08:13:01 +00:00
/*
* Initialize locks that may be required during
* en/deslave operations. All of the bond_open work
* (of which this is part) should really be moved to
* a phase prior to dev_open
*/
spin_lock_init(&(bond_info->tx_hashtbl_lock));
spin_lock_init(&(bond_info->rx_hashtbl_lock));
bond->wq = create_singlethread_workqueue(bond_dev->name);
if (!bond->wq)
return -ENOMEM;
bond_set_lockdep_class(bond_dev);
list_add_tail(&bond->bond_list, &bn->dev_list);
bond_prepare_sysfs_group(bond);
bond_debug_register(bond);
__hw_addr_init(&bond->mc_list);
return 0;
}
static int bond_validate(struct nlattr *tb[], struct nlattr *data[])
{
if (tb[IFLA_ADDRESS]) {
if (nla_len(tb[IFLA_ADDRESS]) != ETH_ALEN)
return -EINVAL;
if (!is_valid_ether_addr(nla_data(tb[IFLA_ADDRESS])))
return -EADDRNOTAVAIL;
}
return 0;
}
static unsigned int bond_get_num_tx_queues(void)
{
return tx_queues;
}
static struct rtnl_link_ops bond_link_ops __read_mostly = {
.kind = "bond",
.priv_size = sizeof(struct bonding),
.setup = bond_setup,
.validate = bond_validate,
.get_num_tx_queues = bond_get_num_tx_queues,
.get_num_rx_queues = bond_get_num_tx_queues, /* Use the same number
as for TX queues */
};
/* Create a new bond based on the specified name and bonding parameters.
* If name is NULL, obtain a suitable "bond%d" name for us.
* Caller must NOT hold rtnl_lock; we need to release it here before we
* set up our sysfs entries.
*/
int bond_create(struct net *net, const char *name)
{
struct net_device *bond_dev;
int res;
rtnl_lock();
bond_dev = alloc_netdev_mq(sizeof(struct bonding),
name ? name : "bond%d",
bond_setup, tx_queues);
if (!bond_dev) {
pr_err("%s: eek! can't alloc netdev!\n", name);
rtnl_unlock();
return -ENOMEM;
}
dev_net_set(bond_dev, net);
bond_dev->rtnl_link_ops = &bond_link_ops;
res = register_netdevice(bond_dev);
netif_carrier_off(bond_dev);
rtnl_unlock();
if (res < 0)
bond_destructor(bond_dev);
return res;
}
static int __net_init bond_net_init(struct net *net)
{
struct bond_net *bn = net_generic(net, bond_net_id);
bn->net = net;
INIT_LIST_HEAD(&bn->dev_list);
bond_create_proc_dir(bn);
bond_create_sysfs(bn);
return 0;
}
static void __net_exit bond_net_exit(struct net *net)
{
struct bond_net *bn = net_generic(net, bond_net_id);
bond_destroy_sysfs(bn);
bond_destroy_proc_dir(bn);
}
static struct pernet_operations bond_net_ops = {
.init = bond_net_init,
.exit = bond_net_exit,
.id = &bond_net_id,
.size = sizeof(struct bond_net),
};
static int __init bonding_init(void)
{
int i;
int res;
pr_info("%s", bond_version);
res = bond_check_params(&bonding_defaults);
if (res)
goto out;
res = register_pernet_subsys(&bond_net_ops);
if (res)
goto out;
res = rtnl_link_register(&bond_link_ops);
if (res)
goto err_link;
bond_create_debugfs();
for (i = 0; i < max_bonds; i++) {
res = bond_create(&init_net, NULL);
if (res)
goto err;
}
register_netdevice_notifier(&bond_netdev_notifier);
out:
return res;
err:
rtnl_link_unregister(&bond_link_ops);
err_link:
unregister_pernet_subsys(&bond_net_ops);
goto out;
}
static void __exit bonding_exit(void)
{
unregister_netdevice_notifier(&bond_netdev_notifier);
bond_destroy_debugfs();
rtnl_link_unregister(&bond_link_ops);
unregister_pernet_subsys(&bond_net_ops);
#ifdef CONFIG_NET_POLL_CONTROLLER
net: Convert netpoll blocking api in bonding driver to be a counter A while back I made some changes to enable netpoll in the bonding driver. Among them was a per-cpu flag that indicated we were in a path that held locks which could cause the netpoll path to block in during tx, and as such the tx path should queue the frame for later use. This appears to have given rise to a regression. If one of those paths on which we hold the per-cpu flag yields the cpu, its possible for us to come back on a different cpu, leading to us clearing a different flag than we set. This results in odd netpoll drops, and BUG backtraces appearing in the log, as we check to make sure that we only clear set bits, and only set clear bits. I had though briefly about changing the offending paths so that they wouldn't sleep, but looking at my origional work more closely, it doesn't appear that a per-cpu flag is warranted. We alrady gate the checking of this flag on IFF_IN_NETPOLL, so we don't hit this in the normal tx case anyway. And practically speaking, the normal use case for netpoll is to only have one client anyway, so we're not going to erroneously queue netpoll frames when its actually safe to do so. As such, lets just convert that per-cpu flag to an atomic counter. It fixes the rescheduling bugs, is equivalent from a performance perspective and actually eliminates some code in the process. Tested by the reporter and myself, successfully Reported-by: Liang Zheng <lzheng@redhat.com> CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: David S. Miller <davem@davemloft.net> Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-06 09:05:50 +00:00
/*
* Make sure we don't have an imbalance on our netpoll blocking
*/
WARN_ON(atomic_read(&netpoll_block_tx));
#endif
}
module_init(bonding_init);
module_exit(bonding_exit);
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);
MODULE_DESCRIPTION(DRV_DESCRIPTION ", v" DRV_VERSION);
MODULE_AUTHOR("Thomas Davis, tadavis@lbl.gov and many others");
MODULE_ALIAS_RTNL_LINK("bond");