2008-08-27 16:53:02 +00:00
|
|
|
#ifndef LINUX_B43_PHY_G_H_
|
|
|
|
#define LINUX_B43_PHY_G_H_
|
|
|
|
|
|
|
|
/* OFDM PHY registers are defined in the A-PHY header. */
|
|
|
|
#include "phy_a.h"
|
|
|
|
|
|
|
|
/* CCK (B) PHY Registers */
|
|
|
|
#define B43_PHY_VERSION_CCK B43_PHY_CCK(0x00) /* Versioning register for B-PHY */
|
|
|
|
#define B43_PHY_CCKBBANDCFG B43_PHY_CCK(0x01) /* Contains antenna 0/1 control bit */
|
|
|
|
#define B43_PHY_PGACTL B43_PHY_CCK(0x15) /* PGA control */
|
|
|
|
#define B43_PHY_PGACTL_LPF 0x1000 /* Low pass filter (?) */
|
|
|
|
#define B43_PHY_PGACTL_LOWBANDW 0x0040 /* Low bandwidth flag */
|
|
|
|
#define B43_PHY_PGACTL_UNKNOWN 0xEFA0
|
|
|
|
#define B43_PHY_FBCTL1 B43_PHY_CCK(0x18) /* Frequency bandwidth control 1 */
|
|
|
|
#define B43_PHY_ITSSI B43_PHY_CCK(0x29) /* Idle TSSI */
|
|
|
|
#define B43_PHY_LO_LEAKAGE B43_PHY_CCK(0x2D) /* Measured LO leakage */
|
|
|
|
#define B43_PHY_ENERGY B43_PHY_CCK(0x33) /* Energy */
|
|
|
|
#define B43_PHY_SYNCCTL B43_PHY_CCK(0x35)
|
|
|
|
#define B43_PHY_FBCTL2 B43_PHY_CCK(0x38) /* Frequency bandwidth control 2 */
|
|
|
|
#define B43_PHY_DACCTL B43_PHY_CCK(0x60) /* DAC control */
|
|
|
|
#define B43_PHY_RCCALOVER B43_PHY_CCK(0x78) /* RC calibration override */
|
|
|
|
|
|
|
|
/* Extended G-PHY Registers */
|
|
|
|
#define B43_PHY_CLASSCTL B43_PHY_EXTG(0x02) /* Classify control */
|
|
|
|
#define B43_PHY_GTABCTL B43_PHY_EXTG(0x03) /* G-PHY table control (see below) */
|
|
|
|
#define B43_PHY_GTABOFF 0x03FF /* G-PHY table offset (see below) */
|
|
|
|
#define B43_PHY_GTABNR 0xFC00 /* G-PHY table number (see below) */
|
|
|
|
#define B43_PHY_GTABNR_SHIFT 10
|
|
|
|
#define B43_PHY_GTABDATA B43_PHY_EXTG(0x04) /* G-PHY table data */
|
|
|
|
#define B43_PHY_LO_MASK B43_PHY_EXTG(0x0F) /* Local Oscillator control mask */
|
|
|
|
#define B43_PHY_LO_CTL B43_PHY_EXTG(0x10) /* Local Oscillator control */
|
|
|
|
#define B43_PHY_RFOVER B43_PHY_EXTG(0x11) /* RF override */
|
|
|
|
#define B43_PHY_RFOVERVAL B43_PHY_EXTG(0x12) /* RF override value */
|
|
|
|
#define B43_PHY_RFOVERVAL_EXTLNA 0x8000
|
|
|
|
#define B43_PHY_RFOVERVAL_LNA 0x7000
|
|
|
|
#define B43_PHY_RFOVERVAL_LNA_SHIFT 12
|
|
|
|
#define B43_PHY_RFOVERVAL_PGA 0x0F00
|
|
|
|
#define B43_PHY_RFOVERVAL_PGA_SHIFT 8
|
|
|
|
#define B43_PHY_RFOVERVAL_UNK 0x0010 /* Unknown, always set. */
|
|
|
|
#define B43_PHY_RFOVERVAL_TRSWRX 0x00E0
|
|
|
|
#define B43_PHY_RFOVERVAL_BW 0x0003 /* Bandwidth flags */
|
|
|
|
#define B43_PHY_RFOVERVAL_BW_LPF 0x0001 /* Low Pass Filter */
|
|
|
|
#define B43_PHY_RFOVERVAL_BW_LBW 0x0002 /* Low Bandwidth (when set), high when unset */
|
|
|
|
#define B43_PHY_ANALOGOVER B43_PHY_EXTG(0x14) /* Analog override */
|
|
|
|
#define B43_PHY_ANALOGOVERVAL B43_PHY_EXTG(0x15) /* Analog override value */
|
|
|
|
|
|
|
|
|
|
|
|
/*** G-PHY table numbers */
|
|
|
|
#define B43_GTAB(number, offset) (((number) << B43_PHY_GTABNR_SHIFT) | (offset))
|
|
|
|
#define B43_GTAB_NRSSI B43_GTAB(0x00, 0)
|
|
|
|
#define B43_GTAB_TRFEMW B43_GTAB(0x0C, 0x120)
|
|
|
|
#define B43_GTAB_ORIGTR B43_GTAB(0x2E, 0x298)
|
|
|
|
|
|
|
|
u16 b43_gtab_read(struct b43_wldev *dev, u16 table, u16 offset);
|
|
|
|
void b43_gtab_write(struct b43_wldev *dev, u16 table, u16 offset, u16 value);
|
|
|
|
|
|
|
|
|
|
|
|
/* Returns the boolean whether "TX Magnification" is enabled. */
|
|
|
|
#define has_tx_magnification(phy) \
|
|
|
|
(((phy)->rev >= 2) && \
|
|
|
|
((phy)->radio_ver == 0x2050) && \
|
|
|
|
((phy)->radio_rev == 8))
|
|
|
|
/* Card uses the loopback gain stuff */
|
|
|
|
#define has_loopback_gain(phy) \
|
|
|
|
(((phy)->rev > 1) || ((phy)->gmode))
|
|
|
|
|
|
|
|
/* Radio Attenuation (RF Attenuation) */
|
|
|
|
struct b43_rfatt {
|
|
|
|
u8 att; /* Attenuation value */
|
|
|
|
bool with_padmix; /* Flag, PAD Mixer enabled. */
|
|
|
|
};
|
|
|
|
struct b43_rfatt_list {
|
|
|
|
/* Attenuation values list */
|
|
|
|
const struct b43_rfatt *list;
|
|
|
|
u8 len;
|
|
|
|
/* Minimum/Maximum attenuation values */
|
|
|
|
u8 min_val;
|
|
|
|
u8 max_val;
|
|
|
|
};
|
|
|
|
|
|
|
|
/* Returns true, if the values are the same. */
|
|
|
|
static inline bool b43_compare_rfatt(const struct b43_rfatt *a,
|
|
|
|
const struct b43_rfatt *b)
|
|
|
|
{
|
|
|
|
return ((a->att == b->att) &&
|
|
|
|
(a->with_padmix == b->with_padmix));
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Baseband Attenuation */
|
|
|
|
struct b43_bbatt {
|
|
|
|
u8 att; /* Attenuation value */
|
|
|
|
};
|
|
|
|
struct b43_bbatt_list {
|
|
|
|
/* Attenuation values list */
|
|
|
|
const struct b43_bbatt *list;
|
|
|
|
u8 len;
|
|
|
|
/* Minimum/Maximum attenuation values */
|
|
|
|
u8 min_val;
|
|
|
|
u8 max_val;
|
|
|
|
};
|
|
|
|
|
|
|
|
/* Returns true, if the values are the same. */
|
|
|
|
static inline bool b43_compare_bbatt(const struct b43_bbatt *a,
|
|
|
|
const struct b43_bbatt *b)
|
|
|
|
{
|
|
|
|
return (a->att == b->att);
|
|
|
|
}
|
|
|
|
|
|
|
|
/* tx_control bits. */
|
|
|
|
#define B43_TXCTL_PA3DB 0x40 /* PA Gain 3dB */
|
|
|
|
#define B43_TXCTL_PA2DB 0x20 /* PA Gain 2dB */
|
|
|
|
#define B43_TXCTL_TXMIX 0x10 /* TX Mixer Gain */
|
|
|
|
|
|
|
|
struct b43_txpower_lo_control;
|
|
|
|
|
|
|
|
struct b43_phy_g {
|
|
|
|
/* ACI (adjacent channel interference) flags. */
|
|
|
|
bool aci_enable;
|
|
|
|
bool aci_wlan_automatic;
|
|
|
|
bool aci_hw_rssi;
|
|
|
|
|
|
|
|
/* Radio switched on/off */
|
|
|
|
bool radio_on;
|
|
|
|
struct {
|
|
|
|
/* Values saved when turning the radio off.
|
|
|
|
* They are needed when turning it on again. */
|
|
|
|
bool valid;
|
|
|
|
u16 rfover;
|
|
|
|
u16 rfoverval;
|
|
|
|
} radio_off_context;
|
|
|
|
|
|
|
|
u16 minlowsig[2];
|
|
|
|
u16 minlowsigpos[2];
|
|
|
|
|
2008-08-28 17:33:40 +00:00
|
|
|
/* Pointer to the table used to convert a
|
|
|
|
* TSSI value to dBm-Q5.2 */
|
2008-08-27 16:53:02 +00:00
|
|
|
const s8 *tssi2dbm;
|
2008-08-28 17:33:40 +00:00
|
|
|
/* tssi2dbm is kmalloc()ed. Only used for free()ing. */
|
|
|
|
bool dyn_tssi_tbl;
|
2008-08-27 16:53:02 +00:00
|
|
|
/* Target idle TSSI */
|
|
|
|
int tgt_idle_tssi;
|
|
|
|
/* Current idle TSSI */
|
|
|
|
int cur_idle_tssi;
|
2008-08-28 17:33:40 +00:00
|
|
|
/* The current average TSSI.
|
|
|
|
* Needs irq_lock, as it's updated in the IRQ path. */
|
|
|
|
u8 average_tssi;
|
|
|
|
/* Current TX power level attenuation control values */
|
|
|
|
struct b43_bbatt bbatt;
|
|
|
|
struct b43_rfatt rfatt;
|
|
|
|
u8 tx_control; /* B43_TXCTL_XXX */
|
|
|
|
/* The calculated attenuation deltas that are used later
|
|
|
|
* when adjusting the actual power output. */
|
|
|
|
int bbatt_delta;
|
|
|
|
int rfatt_delta;
|
2008-08-27 16:53:02 +00:00
|
|
|
|
|
|
|
/* LocalOscillator control values. */
|
|
|
|
struct b43_txpower_lo_control *lo_control;
|
|
|
|
/* Values from b43_calc_loopback_gain() */
|
|
|
|
s16 max_lb_gain; /* Maximum Loopback gain in hdB */
|
|
|
|
s16 trsw_rx_gain; /* TRSW RX gain in hdB */
|
|
|
|
s16 lna_lod_gain; /* LNA lod */
|
|
|
|
s16 lna_gain; /* LNA */
|
|
|
|
s16 pga_gain; /* PGA */
|
|
|
|
|
|
|
|
/* Current Interference Mitigation mode */
|
|
|
|
int interfmode;
|
|
|
|
/* Stack of saved values from the Interference Mitigation code.
|
|
|
|
* Each value in the stack is layed out as follows:
|
|
|
|
* bit 0-11: offset
|
|
|
|
* bit 12-15: register ID
|
|
|
|
* bit 16-32: value
|
|
|
|
* register ID is: 0x1 PHY, 0x2 Radio, 0x3 ILT
|
|
|
|
*/
|
|
|
|
#define B43_INTERFSTACK_SIZE 26
|
|
|
|
u32 interfstack[B43_INTERFSTACK_SIZE]; //FIXME: use a data structure
|
|
|
|
|
|
|
|
/* Saved values from the NRSSI Slope calculation */
|
|
|
|
s16 nrssi[2];
|
|
|
|
s32 nrssislope;
|
|
|
|
/* In memory nrssi lookup table. */
|
|
|
|
s8 nrssi_lt[64];
|
|
|
|
|
|
|
|
u16 lofcal;
|
|
|
|
|
|
|
|
u16 initval; //FIXME rename?
|
|
|
|
|
|
|
|
/* The device does address auto increment for the OFDM tables.
|
|
|
|
* We cache the previously used address here and omit the address
|
|
|
|
* write on the next table access, if possible. */
|
|
|
|
u16 ofdmtab_addr; /* The address currently set in hardware. */
|
|
|
|
enum { /* The last data flow direction. */
|
|
|
|
B43_OFDMTAB_DIRECTION_UNKNOWN = 0,
|
|
|
|
B43_OFDMTAB_DIRECTION_READ,
|
|
|
|
B43_OFDMTAB_DIRECTION_WRITE,
|
|
|
|
} ofdmtab_addr_direction;
|
|
|
|
};
|
|
|
|
|
|
|
|
void b43_gphy_set_baseband_attenuation(struct b43_wldev *dev,
|
|
|
|
u16 baseband_attenuation);
|
|
|
|
void b43_gphy_channel_switch(struct b43_wldev *dev,
|
|
|
|
unsigned int channel,
|
|
|
|
bool synthetic_pu_workaround);
|
2008-08-30 00:09:08 +00:00
|
|
|
u8 * b43_generate_dyn_tssi2dbm_tab(struct b43_wldev *dev,
|
|
|
|
s16 pab0, s16 pab1, s16 pab2);
|
2008-08-27 16:53:02 +00:00
|
|
|
|
|
|
|
struct b43_phy_operations;
|
|
|
|
extern const struct b43_phy_operations b43_phyops_g;
|
|
|
|
|
|
|
|
#endif /* LINUX_B43_PHY_G_H_ */
|