2005-04-16 22:20:36 +00:00
|
|
|
/*
|
2007-02-28 14:33:10 +00:00
|
|
|
* linux/drivers/mmc/core/core.c
|
2005-04-16 22:20:36 +00:00
|
|
|
*
|
|
|
|
* Copyright (C) 2003-2004 Russell King, All Rights Reserved.
|
2005-09-06 22:18:56 +00:00
|
|
|
* SD support Copyright (C) 2004 Ian Molton, All Rights Reserved.
|
2008-06-28 10:52:45 +00:00
|
|
|
* Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved.
|
2006-10-21 10:35:02 +00:00
|
|
|
* MMCv4 support Copyright (C) 2006 Philip Langdale, All Rights Reserved.
|
2005-04-16 22:20:36 +00:00
|
|
|
*
|
|
|
|
* This program is free software; you can redistribute it and/or modify
|
|
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
|
|
* published by the Free Software Foundation.
|
|
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
|
|
#include <linux/init.h>
|
|
|
|
#include <linux/interrupt.h>
|
|
|
|
#include <linux/completion.h>
|
|
|
|
#include <linux/device.h>
|
|
|
|
#include <linux/delay.h>
|
|
|
|
#include <linux/pagemap.h>
|
|
|
|
#include <linux/err.h>
|
2007-09-24 05:15:48 +00:00
|
|
|
#include <linux/leds.h>
|
2005-09-06 22:18:53 +00:00
|
|
|
#include <linux/scatterlist.h>
|
2008-11-26 19:54:17 +00:00
|
|
|
#include <linux/log2.h>
|
2009-03-11 11:30:43 +00:00
|
|
|
#include <linux/regulator/consumer.h>
|
2010-11-28 05:21:30 +00:00
|
|
|
#include <linux/pm_runtime.h>
|
2013-09-20 09:02:35 +00:00
|
|
|
#include <linux/pm_wakeup.h>
|
2011-07-26 00:13:11 +00:00
|
|
|
#include <linux/suspend.h>
|
2011-08-19 12:52:37 +00:00
|
|
|
#include <linux/fault-inject.h>
|
|
|
|
#include <linux/random.h>
|
2012-09-17 08:42:02 +00:00
|
|
|
#include <linux/slab.h>
|
2013-08-26 01:19:22 +00:00
|
|
|
#include <linux/of.h>
|
2005-04-16 22:20:36 +00:00
|
|
|
|
|
|
|
#include <linux/mmc/card.h>
|
|
|
|
#include <linux/mmc/host.h>
|
2006-12-24 21:46:55 +00:00
|
|
|
#include <linux/mmc/mmc.h>
|
|
|
|
#include <linux/mmc/sd.h>
|
2014-03-10 13:02:41 +00:00
|
|
|
#include <linux/mmc/slot-gpio.h>
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2007-02-28 14:33:10 +00:00
|
|
|
#include "core.h"
|
2007-05-19 12:32:22 +00:00
|
|
|
#include "bus.h"
|
|
|
|
#include "host.h"
|
2007-05-26 11:48:18 +00:00
|
|
|
#include "sdio_bus.h"
|
2014-11-28 13:38:36 +00:00
|
|
|
#include "pwrseq.h"
|
2006-12-24 21:46:55 +00:00
|
|
|
|
|
|
|
#include "mmc_ops.h"
|
|
|
|
#include "sd_ops.h"
|
2007-05-21 18:23:20 +00:00
|
|
|
#include "sdio_ops.h"
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2012-11-16 15:31:41 +00:00
|
|
|
/* If the device is not responding */
|
|
|
|
#define MMC_CORE_TIMEOUT_MS (10 * 60 * 1000) /* 10 minute timeout */
|
|
|
|
|
2012-09-17 08:42:02 +00:00
|
|
|
/*
|
|
|
|
* Background operations can take a long time, depending on the housekeeping
|
|
|
|
* operations the card has to perform.
|
|
|
|
*/
|
|
|
|
#define MMC_BKOPS_MAX_TIMEOUT (4 * 60 * 1000) /* max time to wait in ms */
|
|
|
|
|
2007-05-19 12:32:22 +00:00
|
|
|
static struct workqueue_struct *workqueue;
|
2012-05-09 14:15:26 +00:00
|
|
|
static const unsigned freqs[] = { 400000, 300000, 200000, 100000 };
|
2007-05-19 12:32:22 +00:00
|
|
|
|
MMC core learns about SPI
Teach the MMC/SD/SDIO core about using SPI mode.
- Use mmc_host_is_spi() so enumeration works through SPI signaling
and protocols, not just the native versions.
- Provide the SPI response type flags with each request issued,
including requests from the new lock/unlock code.
- Understand that cmd->resp[0] and mmc_get_status() results for SPI
return different values than for "native" MMC/SD protocol; this
affects resetting, checking card lock status, and some others.
- Understand that some commands act a bit differently ... notably:
* OP_COND command doesn't return the OCR
* APP_CMD status doesn't have an R1_APP_CMD analogue
Those changes required some new and updated primitives:
- Provide utilities to access two SPI-only requests, and one
request that wasn't previously needed:
* mmc_spi_read_ocr() ... SPI only
* mmc_spi_set_crc() ... SPI only (override by module parm)
* mmc_send_cid() ... for use without broadcast mode
- Updated internal routines:
* Previous mmc_send_csd() modified into mmc_send_cxd_native();
it uses native "R2" responses, which include 16 bytes of data.
* Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
helper for command-and-data access
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
- Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper
- Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
those helper routines based on whether they're native or SPI
The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
|
|
|
/*
|
|
|
|
* Enabling software CRCs on the data blocks can be a significant (30%)
|
|
|
|
* performance cost, and for other reasons may not always be desired.
|
|
|
|
* So we allow it it to be disabled.
|
|
|
|
*/
|
2012-01-12 23:02:20 +00:00
|
|
|
bool use_spi_crc = 1;
|
MMC core learns about SPI
Teach the MMC/SD/SDIO core about using SPI mode.
- Use mmc_host_is_spi() so enumeration works through SPI signaling
and protocols, not just the native versions.
- Provide the SPI response type flags with each request issued,
including requests from the new lock/unlock code.
- Understand that cmd->resp[0] and mmc_get_status() results for SPI
return different values than for "native" MMC/SD protocol; this
affects resetting, checking card lock status, and some others.
- Understand that some commands act a bit differently ... notably:
* OP_COND command doesn't return the OCR
* APP_CMD status doesn't have an R1_APP_CMD analogue
Those changes required some new and updated primitives:
- Provide utilities to access two SPI-only requests, and one
request that wasn't previously needed:
* mmc_spi_read_ocr() ... SPI only
* mmc_spi_set_crc() ... SPI only (override by module parm)
* mmc_send_cid() ... for use without broadcast mode
- Updated internal routines:
* Previous mmc_send_csd() modified into mmc_send_cxd_native();
it uses native "R2" responses, which include 16 bytes of data.
* Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
helper for command-and-data access
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
- Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper
- Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
those helper routines based on whether they're native or SPI
The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
|
|
|
module_param(use_spi_crc, bool, 0);
|
|
|
|
|
2007-05-19 12:32:22 +00:00
|
|
|
/*
|
|
|
|
* Internal function. Schedule delayed work in the MMC work queue.
|
|
|
|
*/
|
|
|
|
static int mmc_schedule_delayed_work(struct delayed_work *work,
|
|
|
|
unsigned long delay)
|
|
|
|
{
|
|
|
|
return queue_delayed_work(workqueue, work, delay);
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Internal function. Flush all scheduled work from the MMC work queue.
|
|
|
|
*/
|
|
|
|
static void mmc_flush_scheduled_work(void)
|
|
|
|
{
|
|
|
|
flush_workqueue(workqueue);
|
|
|
|
}
|
|
|
|
|
2011-08-19 12:52:37 +00:00
|
|
|
#ifdef CONFIG_FAIL_MMC_REQUEST
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Internal function. Inject random data errors.
|
|
|
|
* If mmc_data is NULL no errors are injected.
|
|
|
|
*/
|
|
|
|
static void mmc_should_fail_request(struct mmc_host *host,
|
|
|
|
struct mmc_request *mrq)
|
|
|
|
{
|
|
|
|
struct mmc_command *cmd = mrq->cmd;
|
|
|
|
struct mmc_data *data = mrq->data;
|
|
|
|
static const int data_errors[] = {
|
|
|
|
-ETIMEDOUT,
|
|
|
|
-EILSEQ,
|
|
|
|
-EIO,
|
|
|
|
};
|
|
|
|
|
|
|
|
if (!data)
|
|
|
|
return;
|
|
|
|
|
|
|
|
if (cmd->error || data->error ||
|
|
|
|
!should_fail(&host->fail_mmc_request, data->blksz * data->blocks))
|
|
|
|
return;
|
|
|
|
|
2013-04-29 23:21:31 +00:00
|
|
|
data->error = data_errors[prandom_u32() % ARRAY_SIZE(data_errors)];
|
|
|
|
data->bytes_xfered = (prandom_u32() % (data->bytes_xfered >> 9)) << 9;
|
2011-08-19 12:52:37 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
#else /* CONFIG_FAIL_MMC_REQUEST */
|
|
|
|
|
|
|
|
static inline void mmc_should_fail_request(struct mmc_host *host,
|
|
|
|
struct mmc_request *mrq)
|
|
|
|
{
|
|
|
|
}
|
|
|
|
|
|
|
|
#endif /* CONFIG_FAIL_MMC_REQUEST */
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
/**
|
2006-05-04 12:51:45 +00:00
|
|
|
* mmc_request_done - finish processing an MMC request
|
|
|
|
* @host: MMC host which completed request
|
|
|
|
* @mrq: MMC request which request
|
2005-04-16 22:20:36 +00:00
|
|
|
*
|
|
|
|
* MMC drivers should call this function when they have completed
|
2006-05-04 12:51:45 +00:00
|
|
|
* their processing of a request.
|
2005-04-16 22:20:36 +00:00
|
|
|
*/
|
|
|
|
void mmc_request_done(struct mmc_host *host, struct mmc_request *mrq)
|
|
|
|
{
|
|
|
|
struct mmc_command *cmd = mrq->cmd;
|
2006-05-04 17:22:51 +00:00
|
|
|
int err = cmd->error;
|
|
|
|
|
2015-05-07 10:10:22 +00:00
|
|
|
/* Flag re-tuning needed on CRC errors */
|
2015-09-30 09:37:18 +00:00
|
|
|
if ((cmd->opcode != MMC_SEND_TUNING_BLOCK &&
|
|
|
|
cmd->opcode != MMC_SEND_TUNING_BLOCK_HS200) &&
|
|
|
|
(err == -EILSEQ || (mrq->sbc && mrq->sbc->error == -EILSEQ) ||
|
2015-05-07 10:10:22 +00:00
|
|
|
(mrq->data && mrq->data->error == -EILSEQ) ||
|
2015-09-30 09:37:18 +00:00
|
|
|
(mrq->stop && mrq->stop->error == -EILSEQ)))
|
2015-05-07 10:10:22 +00:00
|
|
|
mmc_retune_needed(host);
|
|
|
|
|
MMC core learns about SPI
Teach the MMC/SD/SDIO core about using SPI mode.
- Use mmc_host_is_spi() so enumeration works through SPI signaling
and protocols, not just the native versions.
- Provide the SPI response type flags with each request issued,
including requests from the new lock/unlock code.
- Understand that cmd->resp[0] and mmc_get_status() results for SPI
return different values than for "native" MMC/SD protocol; this
affects resetting, checking card lock status, and some others.
- Understand that some commands act a bit differently ... notably:
* OP_COND command doesn't return the OCR
* APP_CMD status doesn't have an R1_APP_CMD analogue
Those changes required some new and updated primitives:
- Provide utilities to access two SPI-only requests, and one
request that wasn't previously needed:
* mmc_spi_read_ocr() ... SPI only
* mmc_spi_set_crc() ... SPI only (override by module parm)
* mmc_send_cid() ... for use without broadcast mode
- Updated internal routines:
* Previous mmc_send_csd() modified into mmc_send_cxd_native();
it uses native "R2" responses, which include 16 bytes of data.
* Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
helper for command-and-data access
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
- Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper
- Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
those helper routines based on whether they're native or SPI
The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-08-08 16:11:32 +00:00
|
|
|
if (err && cmd->retries && mmc_host_is_spi(host)) {
|
|
|
|
if (cmd->resp[0] & R1_SPI_ILLEGAL_COMMAND)
|
|
|
|
cmd->retries = 0;
|
|
|
|
}
|
|
|
|
|
2011-11-28 14:22:00 +00:00
|
|
|
if (err && cmd->retries && !mmc_card_removed(host->card)) {
|
2011-10-03 12:33:33 +00:00
|
|
|
/*
|
|
|
|
* Request starter must handle retries - see
|
|
|
|
* mmc_wait_for_req_done().
|
|
|
|
*/
|
|
|
|
if (mrq->done)
|
|
|
|
mrq->done(mrq);
|
2007-07-24 19:46:49 +00:00
|
|
|
} else {
|
2011-08-19 12:52:37 +00:00
|
|
|
mmc_should_fail_request(host, mrq);
|
|
|
|
|
2007-09-24 05:15:48 +00:00
|
|
|
led_trigger_event(host->led, LED_OFF);
|
|
|
|
|
2014-10-01 12:14:10 +00:00
|
|
|
if (mrq->sbc) {
|
|
|
|
pr_debug("%s: req done <CMD%u>: %d: %08x %08x %08x %08x\n",
|
|
|
|
mmc_hostname(host), mrq->sbc->opcode,
|
|
|
|
mrq->sbc->error,
|
|
|
|
mrq->sbc->resp[0], mrq->sbc->resp[1],
|
|
|
|
mrq->sbc->resp[2], mrq->sbc->resp[3]);
|
|
|
|
}
|
|
|
|
|
2007-07-24 19:46:49 +00:00
|
|
|
pr_debug("%s: req done (CMD%u): %d: %08x %08x %08x %08x\n",
|
|
|
|
mmc_hostname(host), cmd->opcode, err,
|
|
|
|
cmd->resp[0], cmd->resp[1],
|
|
|
|
cmd->resp[2], cmd->resp[3]);
|
|
|
|
|
|
|
|
if (mrq->data) {
|
|
|
|
pr_debug("%s: %d bytes transferred: %d\n",
|
|
|
|
mmc_hostname(host),
|
|
|
|
mrq->data->bytes_xfered, mrq->data->error);
|
|
|
|
}
|
|
|
|
|
|
|
|
if (mrq->stop) {
|
|
|
|
pr_debug("%s: (CMD%u): %d: %08x %08x %08x %08x\n",
|
|
|
|
mmc_hostname(host), mrq->stop->opcode,
|
|
|
|
mrq->stop->error,
|
|
|
|
mrq->stop->resp[0], mrq->stop->resp[1],
|
|
|
|
mrq->stop->resp[2], mrq->stop->resp[3]);
|
|
|
|
}
|
|
|
|
|
|
|
|
if (mrq->done)
|
|
|
|
mrq->done(mrq);
|
2010-11-09 02:36:50 +00:00
|
|
|
|
2011-08-18 12:23:47 +00:00
|
|
|
mmc_host_clk_release(host);
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
EXPORT_SYMBOL(mmc_request_done);
|
|
|
|
|
2015-05-07 10:10:14 +00:00
|
|
|
static void __mmc_start_request(struct mmc_host *host, struct mmc_request *mrq)
|
|
|
|
{
|
|
|
|
int err;
|
|
|
|
|
|
|
|
/* Assumes host controller has been runtime resumed by mmc_claim_host */
|
|
|
|
err = mmc_retune(host);
|
|
|
|
if (err) {
|
|
|
|
mrq->cmd->error = err;
|
|
|
|
mmc_request_done(host, mrq);
|
|
|
|
return;
|
|
|
|
}
|
|
|
|
|
|
|
|
host->ops->request(host, mrq);
|
|
|
|
}
|
|
|
|
|
2014-12-05 17:41:02 +00:00
|
|
|
static int mmc_start_request(struct mmc_host *host, struct mmc_request *mrq)
|
2005-04-16 22:20:36 +00:00
|
|
|
{
|
2007-04-13 20:47:01 +00:00
|
|
|
#ifdef CONFIG_MMC_DEBUG
|
|
|
|
unsigned int i, sz;
|
2008-07-28 23:09:37 +00:00
|
|
|
struct scatterlist *sg;
|
2007-04-13 20:47:01 +00:00
|
|
|
#endif
|
2015-05-07 10:10:14 +00:00
|
|
|
mmc_retune_hold(host);
|
|
|
|
|
2014-12-05 17:41:02 +00:00
|
|
|
if (mmc_card_removed(host->card))
|
|
|
|
return -ENOMEDIUM;
|
2007-04-13 20:47:01 +00:00
|
|
|
|
2012-02-07 05:13:10 +00:00
|
|
|
if (mrq->sbc) {
|
|
|
|
pr_debug("<%s: starting CMD%u arg %08x flags %08x>\n",
|
|
|
|
mmc_hostname(host), mrq->sbc->opcode,
|
|
|
|
mrq->sbc->arg, mrq->sbc->flags);
|
|
|
|
}
|
|
|
|
|
2006-05-04 17:22:51 +00:00
|
|
|
pr_debug("%s: starting CMD%u arg %08x flags %08x\n",
|
|
|
|
mmc_hostname(host), mrq->cmd->opcode,
|
|
|
|
mrq->cmd->arg, mrq->cmd->flags);
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2007-07-24 19:46:49 +00:00
|
|
|
if (mrq->data) {
|
|
|
|
pr_debug("%s: blksz %d blocks %d flags %08x "
|
|
|
|
"tsac %d ms nsac %d\n",
|
|
|
|
mmc_hostname(host), mrq->data->blksz,
|
|
|
|
mrq->data->blocks, mrq->data->flags,
|
2007-08-07 12:06:18 +00:00
|
|
|
mrq->data->timeout_ns / 1000000,
|
2007-07-24 19:46:49 +00:00
|
|
|
mrq->data->timeout_clks);
|
|
|
|
}
|
|
|
|
|
|
|
|
if (mrq->stop) {
|
|
|
|
pr_debug("%s: CMD%u arg %08x flags %08x\n",
|
|
|
|
mmc_hostname(host), mrq->stop->opcode,
|
|
|
|
mrq->stop->arg, mrq->stop->flags);
|
|
|
|
}
|
|
|
|
|
2006-12-26 14:11:23 +00:00
|
|
|
WARN_ON(!host->claimed);
|
2005-04-16 22:20:36 +00:00
|
|
|
|
|
|
|
mrq->cmd->error = 0;
|
|
|
|
mrq->cmd->mrq = mrq;
|
2014-10-01 12:14:09 +00:00
|
|
|
if (mrq->sbc) {
|
|
|
|
mrq->sbc->error = 0;
|
|
|
|
mrq->sbc->mrq = mrq;
|
|
|
|
}
|
2005-04-16 22:20:36 +00:00
|
|
|
if (mrq->data) {
|
2006-11-21 16:54:23 +00:00
|
|
|
BUG_ON(mrq->data->blksz > host->max_blk_size);
|
2006-11-21 16:55:45 +00:00
|
|
|
BUG_ON(mrq->data->blocks > host->max_blk_count);
|
|
|
|
BUG_ON(mrq->data->blocks * mrq->data->blksz >
|
|
|
|
host->max_req_size);
|
2006-11-21 16:54:23 +00:00
|
|
|
|
2007-04-13 20:47:01 +00:00
|
|
|
#ifdef CONFIG_MMC_DEBUG
|
|
|
|
sz = 0;
|
2008-07-28 23:09:37 +00:00
|
|
|
for_each_sg(mrq->data->sg, sg, mrq->data->sg_len, i)
|
|
|
|
sz += sg->length;
|
2007-04-13 20:47:01 +00:00
|
|
|
BUG_ON(sz != mrq->data->blocks * mrq->data->blksz);
|
|
|
|
#endif
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
mrq->cmd->data = mrq->data;
|
|
|
|
mrq->data->error = 0;
|
|
|
|
mrq->data->mrq = mrq;
|
|
|
|
if (mrq->stop) {
|
|
|
|
mrq->data->stop = mrq->stop;
|
|
|
|
mrq->stop->error = 0;
|
|
|
|
mrq->stop->mrq = mrq;
|
|
|
|
}
|
|
|
|
}
|
2011-08-18 12:23:47 +00:00
|
|
|
mmc_host_clk_hold(host);
|
2011-02-06 18:02:48 +00:00
|
|
|
led_trigger_event(host->led, LED_FULL);
|
2015-05-07 10:10:14 +00:00
|
|
|
__mmc_start_request(host, mrq);
|
2014-12-05 17:41:02 +00:00
|
|
|
|
|
|
|
return 0;
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
|
|
|
|
2012-09-17 08:42:02 +00:00
|
|
|
/**
|
|
|
|
* mmc_start_bkops - start BKOPS for supported cards
|
|
|
|
* @card: MMC card to start BKOPS
|
|
|
|
* @form_exception: A flag to indicate if this function was
|
|
|
|
* called due to an exception raised by the card
|
|
|
|
*
|
|
|
|
* Start background operations whenever requested.
|
|
|
|
* When the urgent BKOPS bit is set in a R1 command response
|
|
|
|
* then background operations should be started immediately.
|
|
|
|
*/
|
|
|
|
void mmc_start_bkops(struct mmc_card *card, bool from_exception)
|
|
|
|
{
|
|
|
|
int err;
|
|
|
|
int timeout;
|
|
|
|
bool use_busy_signal;
|
|
|
|
|
|
|
|
BUG_ON(!card);
|
|
|
|
|
2015-01-29 08:49:43 +00:00
|
|
|
if (!card->ext_csd.man_bkops_en || mmc_card_doing_bkops(card))
|
2012-09-17 08:42:02 +00:00
|
|
|
return;
|
|
|
|
|
|
|
|
err = mmc_read_bkops_status(card);
|
|
|
|
if (err) {
|
|
|
|
pr_err("%s: Failed to read bkops status: %d\n",
|
|
|
|
mmc_hostname(card->host), err);
|
|
|
|
return;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (!card->ext_csd.raw_bkops_status)
|
|
|
|
return;
|
|
|
|
|
|
|
|
if (card->ext_csd.raw_bkops_status < EXT_CSD_BKOPS_LEVEL_2 &&
|
|
|
|
from_exception)
|
|
|
|
return;
|
|
|
|
|
|
|
|
mmc_claim_host(card->host);
|
|
|
|
if (card->ext_csd.raw_bkops_status >= EXT_CSD_BKOPS_LEVEL_2) {
|
|
|
|
timeout = MMC_BKOPS_MAX_TIMEOUT;
|
|
|
|
use_busy_signal = true;
|
|
|
|
} else {
|
|
|
|
timeout = 0;
|
|
|
|
use_busy_signal = false;
|
|
|
|
}
|
|
|
|
|
2015-05-07 10:10:17 +00:00
|
|
|
mmc_retune_hold(card->host);
|
|
|
|
|
2012-09-17 08:42:02 +00:00
|
|
|
err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
|
2014-01-08 15:09:33 +00:00
|
|
|
EXT_CSD_BKOPS_START, 1, timeout,
|
|
|
|
use_busy_signal, true, false);
|
2012-09-17 08:42:02 +00:00
|
|
|
if (err) {
|
|
|
|
pr_warn("%s: Error %d starting bkops\n",
|
|
|
|
mmc_hostname(card->host), err);
|
2015-05-07 10:10:17 +00:00
|
|
|
mmc_retune_release(card->host);
|
2012-09-17 08:42:02 +00:00
|
|
|
goto out;
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* For urgent bkops status (LEVEL_2 and more)
|
|
|
|
* bkops executed synchronously, otherwise
|
|
|
|
* the operation is in progress
|
|
|
|
*/
|
|
|
|
if (!use_busy_signal)
|
|
|
|
mmc_card_set_doing_bkops(card);
|
2015-05-07 10:10:17 +00:00
|
|
|
else
|
|
|
|
mmc_retune_release(card->host);
|
2012-09-17 08:42:02 +00:00
|
|
|
out:
|
|
|
|
mmc_release_host(card->host);
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_start_bkops);
|
|
|
|
|
2013-01-14 19:28:17 +00:00
|
|
|
/*
|
|
|
|
* mmc_wait_data_done() - done callback for data request
|
|
|
|
* @mrq: done data request
|
|
|
|
*
|
|
|
|
* Wakes up mmc context, passed as a callback to host controller driver
|
|
|
|
*/
|
|
|
|
static void mmc_wait_data_done(struct mmc_request *mrq)
|
|
|
|
{
|
mmc: core: fix race condition in mmc_wait_data_done
The following panic is captured in ker3.14, but the issue still exists
in latest kernel.
---------------------------------------------------------------------
[ 20.738217] c0 3136 (Compiler) Unable to handle kernel NULL pointer dereference
at virtual address 00000578
......
[ 20.738499] c0 3136 (Compiler) PC is at _raw_spin_lock_irqsave+0x24/0x60
[ 20.738527] c0 3136 (Compiler) LR is at _raw_spin_lock_irqsave+0x20/0x60
[ 20.740134] c0 3136 (Compiler) Call trace:
[ 20.740165] c0 3136 (Compiler) [<ffffffc0008ee900>] _raw_spin_lock_irqsave+0x24/0x60
[ 20.740200] c0 3136 (Compiler) [<ffffffc0000dd024>] __wake_up+0x1c/0x54
[ 20.740230] c0 3136 (Compiler) [<ffffffc000639414>] mmc_wait_data_done+0x28/0x34
[ 20.740262] c0 3136 (Compiler) [<ffffffc0006391a0>] mmc_request_done+0xa4/0x220
[ 20.740314] c0 3136 (Compiler) [<ffffffc000656894>] sdhci_tasklet_finish+0xac/0x264
[ 20.740352] c0 3136 (Compiler) [<ffffffc0000a2b58>] tasklet_action+0xa0/0x158
[ 20.740382] c0 3136 (Compiler) [<ffffffc0000a2078>] __do_softirq+0x10c/0x2e4
[ 20.740411] c0 3136 (Compiler) [<ffffffc0000a24bc>] irq_exit+0x8c/0xc0
[ 20.740439] c0 3136 (Compiler) [<ffffffc00008489c>] handle_IRQ+0x48/0xac
[ 20.740469] c0 3136 (Compiler) [<ffffffc000081428>] gic_handle_irq+0x38/0x7c
----------------------------------------------------------------------
Because in SMP, "mrq" has race condition between below two paths:
path1: CPU0: <tasklet context>
static void mmc_wait_data_done(struct mmc_request *mrq)
{
mrq->host->context_info.is_done_rcv = true;
//
// If CPU0 has just finished "is_done_rcv = true" in path1, and at
// this moment, IRQ or ICache line missing happens in CPU0.
// What happens in CPU1 (path2)?
//
// If the mmcqd thread in CPU1(path2) hasn't entered to sleep mode:
// path2 would have chance to break from wait_event_interruptible
// in mmc_wait_for_data_req_done and continue to run for next
// mmc_request (mmc_blk_rw_rq_prep).
//
// Within mmc_blk_rq_prep, mrq is cleared to 0.
// If below line still gets host from "mrq" as the result of
// compiler, the panic happens as we traced.
wake_up_interruptible(&mrq->host->context_info.wait);
}
path2: CPU1: <The mmcqd thread runs mmc_queue_thread>
static int mmc_wait_for_data_req_done(...
{
...
while (1) {
wait_event_interruptible(context_info->wait,
(context_info->is_done_rcv ||
context_info->is_new_req));
static void mmc_blk_rw_rq_prep(...
{
...
memset(brq, 0, sizeof(struct mmc_blk_request));
This issue happens very coincidentally; however adding mdelay(1) in
mmc_wait_data_done as below could duplicate it easily.
static void mmc_wait_data_done(struct mmc_request *mrq)
{
mrq->host->context_info.is_done_rcv = true;
+ mdelay(1);
wake_up_interruptible(&mrq->host->context_info.wait);
}
At runtime, IRQ or ICache line missing may just happen at the same place
of the mdelay(1).
This patch gets the mmc_context_info at the beginning of function, it can
avoid this race condition.
Signed-off-by: Jialing Fu <jlfu@marvell.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 2220eedfd7ae ("mmc: fix async request mechanism ....")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-08-28 03:13:09 +00:00
|
|
|
struct mmc_context_info *context_info = &mrq->host->context_info;
|
|
|
|
|
|
|
|
context_info->is_done_rcv = true;
|
|
|
|
wake_up_interruptible(&context_info->wait);
|
2013-01-14 19:28:17 +00:00
|
|
|
}
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
static void mmc_wait_done(struct mmc_request *mrq)
|
|
|
|
{
|
2011-07-01 16:55:22 +00:00
|
|
|
complete(&mrq->completion);
|
|
|
|
}
|
|
|
|
|
2013-01-14 19:28:17 +00:00
|
|
|
/*
|
|
|
|
*__mmc_start_data_req() - starts data request
|
|
|
|
* @host: MMC host to start the request
|
|
|
|
* @mrq: data request to start
|
|
|
|
*
|
|
|
|
* Sets the done callback to be called when request is completed by the card.
|
|
|
|
* Starts data mmc request execution
|
|
|
|
*/
|
|
|
|
static int __mmc_start_data_req(struct mmc_host *host, struct mmc_request *mrq)
|
|
|
|
{
|
2014-12-05 17:41:02 +00:00
|
|
|
int err;
|
|
|
|
|
2013-01-14 19:28:17 +00:00
|
|
|
mrq->done = mmc_wait_data_done;
|
|
|
|
mrq->host = host;
|
2014-12-05 17:41:02 +00:00
|
|
|
|
|
|
|
err = mmc_start_request(host, mrq);
|
|
|
|
if (err) {
|
|
|
|
mrq->cmd->error = err;
|
2013-01-22 10:48:03 +00:00
|
|
|
mmc_wait_data_done(mrq);
|
2013-01-14 19:28:17 +00:00
|
|
|
}
|
|
|
|
|
2014-12-05 17:41:02 +00:00
|
|
|
return err;
|
2013-01-14 19:28:17 +00:00
|
|
|
}
|
|
|
|
|
2012-03-05 14:52:43 +00:00
|
|
|
static int __mmc_start_req(struct mmc_host *host, struct mmc_request *mrq)
|
2011-07-01 16:55:22 +00:00
|
|
|
{
|
2014-12-05 17:41:02 +00:00
|
|
|
int err;
|
|
|
|
|
2011-07-01 16:55:22 +00:00
|
|
|
init_completion(&mrq->completion);
|
|
|
|
mrq->done = mmc_wait_done;
|
2014-12-05 17:41:02 +00:00
|
|
|
|
|
|
|
err = mmc_start_request(host, mrq);
|
|
|
|
if (err) {
|
|
|
|
mrq->cmd->error = err;
|
2011-11-28 14:22:00 +00:00
|
|
|
complete(&mrq->completion);
|
|
|
|
}
|
2014-12-05 17:41:02 +00:00
|
|
|
|
|
|
|
return err;
|
2011-07-01 16:55:22 +00:00
|
|
|
}
|
|
|
|
|
2013-01-14 19:28:17 +00:00
|
|
|
/*
|
|
|
|
* mmc_wait_for_data_req_done() - wait for request completed
|
|
|
|
* @host: MMC host to prepare the command.
|
|
|
|
* @mrq: MMC request to wait for
|
|
|
|
*
|
|
|
|
* Blocks MMC context till host controller will ack end of data request
|
|
|
|
* execution or new request notification arrives from the block layer.
|
|
|
|
* Handles command retries.
|
|
|
|
*
|
|
|
|
* Returns enum mmc_blk_status after checking errors.
|
|
|
|
*/
|
|
|
|
static int mmc_wait_for_data_req_done(struct mmc_host *host,
|
|
|
|
struct mmc_request *mrq,
|
|
|
|
struct mmc_async_req *next_req)
|
|
|
|
{
|
|
|
|
struct mmc_command *cmd;
|
|
|
|
struct mmc_context_info *context_info = &host->context_info;
|
|
|
|
int err;
|
|
|
|
unsigned long flags;
|
|
|
|
|
|
|
|
while (1) {
|
|
|
|
wait_event_interruptible(context_info->wait,
|
|
|
|
(context_info->is_done_rcv ||
|
|
|
|
context_info->is_new_req));
|
|
|
|
spin_lock_irqsave(&context_info->lock, flags);
|
|
|
|
context_info->is_waiting_last_req = false;
|
|
|
|
spin_unlock_irqrestore(&context_info->lock, flags);
|
|
|
|
if (context_info->is_done_rcv) {
|
|
|
|
context_info->is_done_rcv = false;
|
|
|
|
context_info->is_new_req = false;
|
|
|
|
cmd = mrq->cmd;
|
2013-04-18 12:41:55 +00:00
|
|
|
|
2013-01-14 19:28:17 +00:00
|
|
|
if (!cmd->error || !cmd->retries ||
|
|
|
|
mmc_card_removed(host->card)) {
|
|
|
|
err = host->areq->err_check(host->card,
|
|
|
|
host->areq);
|
|
|
|
break; /* return err */
|
|
|
|
} else {
|
2015-05-07 10:10:14 +00:00
|
|
|
mmc_retune_recheck(host);
|
2013-01-14 19:28:17 +00:00
|
|
|
pr_info("%s: req failed (CMD%u): %d, retrying...\n",
|
|
|
|
mmc_hostname(host),
|
|
|
|
cmd->opcode, cmd->error);
|
|
|
|
cmd->retries--;
|
|
|
|
cmd->error = 0;
|
2015-05-07 10:10:14 +00:00
|
|
|
__mmc_start_request(host, mrq);
|
2013-01-14 19:28:17 +00:00
|
|
|
continue; /* wait for done/new event again */
|
|
|
|
}
|
|
|
|
} else if (context_info->is_new_req) {
|
|
|
|
context_info->is_new_req = false;
|
2015-05-07 10:10:14 +00:00
|
|
|
if (!next_req)
|
|
|
|
return MMC_BLK_NEW_REQUEST;
|
2013-01-14 19:28:17 +00:00
|
|
|
}
|
|
|
|
}
|
2015-05-07 10:10:14 +00:00
|
|
|
mmc_retune_release(host);
|
2013-01-14 19:28:17 +00:00
|
|
|
return err;
|
|
|
|
}
|
|
|
|
|
2011-07-01 16:55:22 +00:00
|
|
|
static void mmc_wait_for_req_done(struct mmc_host *host,
|
|
|
|
struct mmc_request *mrq)
|
|
|
|
{
|
2011-10-03 12:33:33 +00:00
|
|
|
struct mmc_command *cmd;
|
|
|
|
|
|
|
|
while (1) {
|
|
|
|
wait_for_completion(&mrq->completion);
|
|
|
|
|
|
|
|
cmd = mrq->cmd;
|
2013-04-18 12:41:55 +00:00
|
|
|
|
|
|
|
/*
|
|
|
|
* If host has timed out waiting for the sanitize
|
|
|
|
* to complete, card might be still in programming state
|
|
|
|
* so let's try to bring the card out of programming
|
|
|
|
* state.
|
|
|
|
*/
|
|
|
|
if (cmd->sanitize_busy && cmd->error == -ETIMEDOUT) {
|
|
|
|
if (!mmc_interrupt_hpi(host->card)) {
|
2014-09-12 21:56:56 +00:00
|
|
|
pr_warn("%s: %s: Interrupted sanitize\n",
|
|
|
|
mmc_hostname(host), __func__);
|
2013-04-18 12:41:55 +00:00
|
|
|
cmd->error = 0;
|
|
|
|
break;
|
|
|
|
} else {
|
|
|
|
pr_err("%s: %s: Failed to interrupt sanitize\n",
|
|
|
|
mmc_hostname(host), __func__);
|
|
|
|
}
|
|
|
|
}
|
2011-11-28 14:22:00 +00:00
|
|
|
if (!cmd->error || !cmd->retries ||
|
|
|
|
mmc_card_removed(host->card))
|
2011-10-03 12:33:33 +00:00
|
|
|
break;
|
|
|
|
|
2015-05-07 10:10:14 +00:00
|
|
|
mmc_retune_recheck(host);
|
|
|
|
|
2011-10-03 12:33:33 +00:00
|
|
|
pr_debug("%s: req failed (CMD%u): %d, retrying...\n",
|
|
|
|
mmc_hostname(host), cmd->opcode, cmd->error);
|
|
|
|
cmd->retries--;
|
|
|
|
cmd->error = 0;
|
2015-05-07 10:10:14 +00:00
|
|
|
__mmc_start_request(host, mrq);
|
2011-10-03 12:33:33 +00:00
|
|
|
}
|
2015-05-07 10:10:14 +00:00
|
|
|
|
|
|
|
mmc_retune_release(host);
|
2011-07-01 16:55:22 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
/**
|
|
|
|
* mmc_pre_req - Prepare for a new request
|
|
|
|
* @host: MMC host to prepare command
|
|
|
|
* @mrq: MMC request to prepare for
|
|
|
|
* @is_first_req: true if there is no previous started request
|
|
|
|
* that may run in parellel to this call, otherwise false
|
|
|
|
*
|
|
|
|
* mmc_pre_req() is called in prior to mmc_start_req() to let
|
|
|
|
* host prepare for the new request. Preparation of a request may be
|
|
|
|
* performed while another request is running on the host.
|
|
|
|
*/
|
|
|
|
static void mmc_pre_req(struct mmc_host *host, struct mmc_request *mrq,
|
|
|
|
bool is_first_req)
|
|
|
|
{
|
2012-02-04 21:14:50 +00:00
|
|
|
if (host->ops->pre_req) {
|
|
|
|
mmc_host_clk_hold(host);
|
2011-07-01 16:55:22 +00:00
|
|
|
host->ops->pre_req(host, mrq, is_first_req);
|
2012-02-04 21:14:50 +00:00
|
|
|
mmc_host_clk_release(host);
|
|
|
|
}
|
2011-07-01 16:55:22 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
/**
|
|
|
|
* mmc_post_req - Post process a completed request
|
|
|
|
* @host: MMC host to post process command
|
|
|
|
* @mrq: MMC request to post process for
|
|
|
|
* @err: Error, if non zero, clean up any resources made in pre_req
|
|
|
|
*
|
|
|
|
* Let the host post process a completed request. Post processing of
|
|
|
|
* a request may be performed while another reuqest is running.
|
|
|
|
*/
|
|
|
|
static void mmc_post_req(struct mmc_host *host, struct mmc_request *mrq,
|
|
|
|
int err)
|
|
|
|
{
|
2012-02-04 21:14:50 +00:00
|
|
|
if (host->ops->post_req) {
|
|
|
|
mmc_host_clk_hold(host);
|
2011-07-01 16:55:22 +00:00
|
|
|
host->ops->post_req(host, mrq, err);
|
2012-02-04 21:14:50 +00:00
|
|
|
mmc_host_clk_release(host);
|
|
|
|
}
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
|
|
|
|
2011-07-01 16:55:22 +00:00
|
|
|
/**
|
|
|
|
* mmc_start_req - start a non-blocking request
|
|
|
|
* @host: MMC host to start command
|
|
|
|
* @areq: async request to start
|
|
|
|
* @error: out parameter returns 0 for success, otherwise non zero
|
|
|
|
*
|
|
|
|
* Start a new MMC custom command request for a host.
|
|
|
|
* If there is on ongoing async request wait for completion
|
|
|
|
* of that request and start the new one and return.
|
|
|
|
* Does not wait for the new request to complete.
|
|
|
|
*
|
|
|
|
* Returns the completed request, NULL in case of none completed.
|
|
|
|
* Wait for the an ongoing request (previoulsy started) to complete and
|
|
|
|
* return the completed request. If there is no ongoing request, NULL
|
|
|
|
* is returned without waiting. NULL is not an error condition.
|
|
|
|
*/
|
|
|
|
struct mmc_async_req *mmc_start_req(struct mmc_host *host,
|
|
|
|
struct mmc_async_req *areq, int *error)
|
|
|
|
{
|
|
|
|
int err = 0;
|
2012-03-05 14:52:43 +00:00
|
|
|
int start_err = 0;
|
2011-07-01 16:55:22 +00:00
|
|
|
struct mmc_async_req *data = host->areq;
|
|
|
|
|
|
|
|
/* Prepare a new request */
|
|
|
|
if (areq)
|
|
|
|
mmc_pre_req(host, areq->mrq, !host->areq);
|
|
|
|
|
|
|
|
if (host->areq) {
|
2013-02-01 05:32:22 +00:00
|
|
|
err = mmc_wait_for_data_req_done(host, host->areq->mrq, areq);
|
|
|
|
if (err == MMC_BLK_NEW_REQUEST) {
|
|
|
|
if (error)
|
|
|
|
*error = err;
|
|
|
|
/*
|
|
|
|
* The previous request was not completed,
|
|
|
|
* nothing to return
|
|
|
|
*/
|
|
|
|
return NULL;
|
|
|
|
}
|
2012-09-17 08:42:02 +00:00
|
|
|
/*
|
|
|
|
* Check BKOPS urgency for each R1 response
|
|
|
|
*/
|
|
|
|
if (host->card && mmc_card_mmc(host->card) &&
|
|
|
|
((mmc_resp_type(host->areq->mrq->cmd) == MMC_RSP_R1) ||
|
|
|
|
(mmc_resp_type(host->areq->mrq->cmd) == MMC_RSP_R1B)) &&
|
2014-10-08 11:24:24 +00:00
|
|
|
(host->areq->mrq->cmd->resp[0] & R1_EXCEPTION_EVENT)) {
|
|
|
|
|
|
|
|
/* Cancel the prepared request */
|
|
|
|
if (areq)
|
|
|
|
mmc_post_req(host, areq->mrq, -EINVAL);
|
|
|
|
|
2012-09-17 08:42:02 +00:00
|
|
|
mmc_start_bkops(host->card, true);
|
2014-10-08 11:24:24 +00:00
|
|
|
|
|
|
|
/* prepare the request again */
|
|
|
|
if (areq)
|
|
|
|
mmc_pre_req(host, areq->mrq, !host->areq);
|
|
|
|
}
|
2011-07-01 16:55:22 +00:00
|
|
|
}
|
|
|
|
|
2012-03-05 14:52:43 +00:00
|
|
|
if (!err && areq)
|
2013-01-14 19:28:17 +00:00
|
|
|
start_err = __mmc_start_data_req(host, areq->mrq);
|
2011-07-01 16:55:22 +00:00
|
|
|
|
|
|
|
if (host->areq)
|
|
|
|
mmc_post_req(host, host->areq->mrq, 0);
|
|
|
|
|
2012-03-05 14:52:43 +00:00
|
|
|
/* Cancel a prepared request if it was not started. */
|
|
|
|
if ((err || start_err) && areq)
|
2013-02-01 05:32:22 +00:00
|
|
|
mmc_post_req(host, areq->mrq, -EINVAL);
|
2012-03-05 14:52:43 +00:00
|
|
|
|
|
|
|
if (err)
|
|
|
|
host->areq = NULL;
|
|
|
|
else
|
|
|
|
host->areq = areq;
|
|
|
|
|
2011-07-01 16:55:22 +00:00
|
|
|
if (error)
|
|
|
|
*error = err;
|
|
|
|
return data;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_start_req);
|
|
|
|
|
2007-07-11 18:22:11 +00:00
|
|
|
/**
|
|
|
|
* mmc_wait_for_req - start a request and wait for completion
|
|
|
|
* @host: MMC host to start command
|
|
|
|
* @mrq: MMC request to start
|
|
|
|
*
|
|
|
|
* Start a new MMC custom command request for a host, and wait
|
|
|
|
* for the command to complete. Does not attempt to parse the
|
|
|
|
* response.
|
|
|
|
*/
|
|
|
|
void mmc_wait_for_req(struct mmc_host *host, struct mmc_request *mrq)
|
2005-04-16 22:20:36 +00:00
|
|
|
{
|
2011-07-01 16:55:22 +00:00
|
|
|
__mmc_start_req(host, mrq);
|
|
|
|
mmc_wait_for_req_done(host, mrq);
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_wait_for_req);
|
|
|
|
|
2011-10-18 05:26:42 +00:00
|
|
|
/**
|
|
|
|
* mmc_interrupt_hpi - Issue for High priority Interrupt
|
|
|
|
* @card: the MMC card associated with the HPI transfer
|
|
|
|
*
|
|
|
|
* Issued High Priority Interrupt, and check for card status
|
2012-09-17 08:42:02 +00:00
|
|
|
* until out-of prg-state.
|
2011-10-18 05:26:42 +00:00
|
|
|
*/
|
|
|
|
int mmc_interrupt_hpi(struct mmc_card *card)
|
|
|
|
{
|
|
|
|
int err;
|
|
|
|
u32 status;
|
2012-06-22 06:12:36 +00:00
|
|
|
unsigned long prg_wait;
|
2011-10-18 05:26:42 +00:00
|
|
|
|
|
|
|
BUG_ON(!card);
|
|
|
|
|
|
|
|
if (!card->ext_csd.hpi_en) {
|
|
|
|
pr_info("%s: HPI enable bit unset\n", mmc_hostname(card->host));
|
|
|
|
return 1;
|
|
|
|
}
|
|
|
|
|
|
|
|
mmc_claim_host(card->host);
|
|
|
|
err = mmc_send_status(card, &status);
|
|
|
|
if (err) {
|
|
|
|
pr_err("%s: Get card status fail\n", mmc_hostname(card->host));
|
|
|
|
goto out;
|
|
|
|
}
|
|
|
|
|
2012-06-22 06:12:36 +00:00
|
|
|
switch (R1_CURRENT_STATE(status)) {
|
|
|
|
case R1_STATE_IDLE:
|
|
|
|
case R1_STATE_READY:
|
|
|
|
case R1_STATE_STBY:
|
2012-08-07 13:54:45 +00:00
|
|
|
case R1_STATE_TRAN:
|
2012-06-22 06:12:36 +00:00
|
|
|
/*
|
2012-08-07 13:54:45 +00:00
|
|
|
* In idle and transfer states, HPI is not needed and the caller
|
2012-06-22 06:12:36 +00:00
|
|
|
* can issue the next intended command immediately
|
|
|
|
*/
|
|
|
|
goto out;
|
|
|
|
case R1_STATE_PRG:
|
|
|
|
break;
|
|
|
|
default:
|
|
|
|
/* In all other states, it's illegal to issue HPI */
|
|
|
|
pr_debug("%s: HPI cannot be sent. Card state=%d\n",
|
|
|
|
mmc_hostname(card->host), R1_CURRENT_STATE(status));
|
|
|
|
err = -EINVAL;
|
|
|
|
goto out;
|
|
|
|
}
|
|
|
|
|
|
|
|
err = mmc_send_hpi_cmd(card, &status);
|
|
|
|
if (err)
|
|
|
|
goto out;
|
|
|
|
|
|
|
|
prg_wait = jiffies + msecs_to_jiffies(card->ext_csd.out_of_int_time);
|
|
|
|
do {
|
|
|
|
err = mmc_send_status(card, &status);
|
|
|
|
|
|
|
|
if (!err && R1_CURRENT_STATE(status) == R1_STATE_TRAN)
|
|
|
|
break;
|
|
|
|
if (time_after(jiffies, prg_wait))
|
|
|
|
err = -ETIMEDOUT;
|
|
|
|
} while (!err);
|
2011-10-18 05:26:42 +00:00
|
|
|
|
|
|
|
out:
|
|
|
|
mmc_release_host(card->host);
|
|
|
|
return err;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_interrupt_hpi);
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
/**
|
|
|
|
* mmc_wait_for_cmd - start a command and wait for completion
|
|
|
|
* @host: MMC host to start command
|
|
|
|
* @cmd: MMC command to start
|
|
|
|
* @retries: maximum number of retries
|
|
|
|
*
|
|
|
|
* Start a new MMC command for a host, and wait for the command
|
|
|
|
* to complete. Return any error that occurred while the command
|
|
|
|
* was executing. Do not attempt to parse the response.
|
|
|
|
*/
|
|
|
|
int mmc_wait_for_cmd(struct mmc_host *host, struct mmc_command *cmd, int retries)
|
|
|
|
{
|
2011-08-24 19:00:50 +00:00
|
|
|
struct mmc_request mrq = {NULL};
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2007-08-09 11:23:56 +00:00
|
|
|
WARN_ON(!host->claimed);
|
2005-04-16 22:20:36 +00:00
|
|
|
|
|
|
|
memset(cmd->resp, 0, sizeof(cmd->resp));
|
|
|
|
cmd->retries = retries;
|
|
|
|
|
|
|
|
mrq.cmd = cmd;
|
|
|
|
cmd->data = NULL;
|
|
|
|
|
|
|
|
mmc_wait_for_req(host, &mrq);
|
|
|
|
|
|
|
|
return cmd->error;
|
|
|
|
}
|
|
|
|
|
|
|
|
EXPORT_SYMBOL(mmc_wait_for_cmd);
|
|
|
|
|
2012-09-17 08:42:02 +00:00
|
|
|
/**
|
|
|
|
* mmc_stop_bkops - stop ongoing BKOPS
|
|
|
|
* @card: MMC card to check BKOPS
|
|
|
|
*
|
|
|
|
* Send HPI command to stop ongoing background operations to
|
|
|
|
* allow rapid servicing of foreground operations, e.g. read/
|
|
|
|
* writes. Wait until the card comes out of the programming state
|
|
|
|
* to avoid errors in servicing read/write requests.
|
|
|
|
*/
|
|
|
|
int mmc_stop_bkops(struct mmc_card *card)
|
|
|
|
{
|
|
|
|
int err = 0;
|
|
|
|
|
|
|
|
BUG_ON(!card);
|
|
|
|
err = mmc_interrupt_hpi(card);
|
|
|
|
|
|
|
|
/*
|
|
|
|
* If err is EINVAL, we can't issue an HPI.
|
|
|
|
* It should complete the BKOPS.
|
|
|
|
*/
|
|
|
|
if (!err || (err == -EINVAL)) {
|
|
|
|
mmc_card_clr_doing_bkops(card);
|
2015-05-07 10:10:17 +00:00
|
|
|
mmc_retune_release(card->host);
|
2012-09-17 08:42:02 +00:00
|
|
|
err = 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
return err;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_stop_bkops);
|
|
|
|
|
|
|
|
int mmc_read_bkops_status(struct mmc_card *card)
|
|
|
|
{
|
|
|
|
int err;
|
|
|
|
u8 *ext_csd;
|
|
|
|
|
|
|
|
mmc_claim_host(card->host);
|
2014-10-17 09:48:23 +00:00
|
|
|
err = mmc_get_ext_csd(card, &ext_csd);
|
2012-09-17 08:42:02 +00:00
|
|
|
mmc_release_host(card->host);
|
|
|
|
if (err)
|
2014-10-17 09:48:23 +00:00
|
|
|
return err;
|
2012-09-17 08:42:02 +00:00
|
|
|
|
|
|
|
card->ext_csd.raw_bkops_status = ext_csd[EXT_CSD_BKOPS_STATUS];
|
|
|
|
card->ext_csd.raw_exception_status = ext_csd[EXT_CSD_EXP_EVENTS_STATUS];
|
|
|
|
kfree(ext_csd);
|
2014-10-17 09:48:23 +00:00
|
|
|
return 0;
|
2012-09-17 08:42:02 +00:00
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_read_bkops_status);
|
|
|
|
|
2006-09-07 14:57:12 +00:00
|
|
|
/**
|
|
|
|
* mmc_set_data_timeout - set the timeout for a data command
|
|
|
|
* @data: data phase for command
|
|
|
|
* @card: the MMC card associated with the data transfer
|
2007-07-11 18:22:11 +00:00
|
|
|
*
|
|
|
|
* Computes the data timeout parameters according to the
|
|
|
|
* correct algorithm given the card type.
|
2006-09-07 14:57:12 +00:00
|
|
|
*/
|
2007-07-24 17:16:54 +00:00
|
|
|
void mmc_set_data_timeout(struct mmc_data *data, const struct mmc_card *card)
|
2006-09-07 14:57:12 +00:00
|
|
|
{
|
|
|
|
unsigned int mult;
|
|
|
|
|
2007-08-07 12:11:55 +00:00
|
|
|
/*
|
|
|
|
* SDIO cards only define an upper 1 s limit on access.
|
|
|
|
*/
|
|
|
|
if (mmc_card_sdio(card)) {
|
|
|
|
data->timeout_ns = 1000000000;
|
|
|
|
data->timeout_clks = 0;
|
|
|
|
return;
|
|
|
|
}
|
|
|
|
|
2006-09-07 14:57:12 +00:00
|
|
|
/*
|
|
|
|
* SD cards use a 100 multiplier rather than 10
|
|
|
|
*/
|
|
|
|
mult = mmc_card_sd(card) ? 100 : 10;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Scale up the multiplier (and therefore the timeout) by
|
|
|
|
* the r2w factor for writes.
|
|
|
|
*/
|
2007-07-24 17:16:54 +00:00
|
|
|
if (data->flags & MMC_DATA_WRITE)
|
2006-09-07 14:57:12 +00:00
|
|
|
mult <<= card->csd.r2w_factor;
|
|
|
|
|
|
|
|
data->timeout_ns = card->csd.tacc_ns * mult;
|
|
|
|
data->timeout_clks = card->csd.tacc_clks * mult;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* SD cards also have an upper limit on the timeout.
|
|
|
|
*/
|
|
|
|
if (mmc_card_sd(card)) {
|
|
|
|
unsigned int timeout_us, limit_us;
|
|
|
|
|
|
|
|
timeout_us = data->timeout_ns / 1000;
|
2011-01-04 23:44:32 +00:00
|
|
|
if (mmc_host_clk_rate(card->host))
|
|
|
|
timeout_us += data->timeout_clks * 1000 /
|
|
|
|
(mmc_host_clk_rate(card->host) / 1000);
|
2006-09-07 14:57:12 +00:00
|
|
|
|
2007-07-24 17:16:54 +00:00
|
|
|
if (data->flags & MMC_DATA_WRITE)
|
2008-10-26 11:37:25 +00:00
|
|
|
/*
|
2012-03-12 10:58:00 +00:00
|
|
|
* The MMC spec "It is strongly recommended
|
|
|
|
* for hosts to implement more than 500ms
|
|
|
|
* timeout value even if the card indicates
|
|
|
|
* the 250ms maximum busy length." Even the
|
|
|
|
* previous value of 300ms is known to be
|
|
|
|
* insufficient for some cards.
|
2008-10-26 11:37:25 +00:00
|
|
|
*/
|
2012-03-12 10:58:00 +00:00
|
|
|
limit_us = 3000000;
|
2006-09-07 14:57:12 +00:00
|
|
|
else
|
|
|
|
limit_us = 100000;
|
|
|
|
|
2007-01-04 14:57:32 +00:00
|
|
|
/*
|
|
|
|
* SDHC cards always use these fixed values.
|
|
|
|
*/
|
|
|
|
if (timeout_us > limit_us || mmc_card_blockaddr(card)) {
|
2006-09-07 14:57:12 +00:00
|
|
|
data->timeout_ns = limit_us * 1000;
|
|
|
|
data->timeout_clks = 0;
|
|
|
|
}
|
2014-04-03 15:32:05 +00:00
|
|
|
|
|
|
|
/* assign limit value if invalid */
|
|
|
|
if (timeout_us == 0)
|
|
|
|
data->timeout_ns = limit_us * 1000;
|
2006-09-07 14:57:12 +00:00
|
|
|
}
|
2011-11-03 08:44:12 +00:00
|
|
|
|
|
|
|
/*
|
|
|
|
* Some cards require longer data read timeout than indicated in CSD.
|
|
|
|
* Address this by setting the read timeout to a "reasonably high"
|
|
|
|
* value. For the cards tested, 300ms has proven enough. If necessary,
|
|
|
|
* this value can be increased if other problematic cards require this.
|
|
|
|
*/
|
|
|
|
if (mmc_card_long_read_time(card) && data->flags & MMC_DATA_READ) {
|
|
|
|
data->timeout_ns = 300000000;
|
|
|
|
data->timeout_clks = 0;
|
|
|
|
}
|
|
|
|
|
2009-03-11 13:28:39 +00:00
|
|
|
/*
|
|
|
|
* Some cards need very high timeouts if driven in SPI mode.
|
|
|
|
* The worst observed timeout was 900ms after writing a
|
|
|
|
* continuous stream of data until the internal logic
|
|
|
|
* overflowed.
|
|
|
|
*/
|
|
|
|
if (mmc_host_is_spi(card->host)) {
|
|
|
|
if (data->flags & MMC_DATA_WRITE) {
|
|
|
|
if (data->timeout_ns < 1000000000)
|
|
|
|
data->timeout_ns = 1000000000; /* 1s */
|
|
|
|
} else {
|
|
|
|
if (data->timeout_ns < 100000000)
|
|
|
|
data->timeout_ns = 100000000; /* 100ms */
|
|
|
|
}
|
|
|
|
}
|
2006-09-07 14:57:12 +00:00
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_set_data_timeout);
|
|
|
|
|
2008-06-28 10:52:45 +00:00
|
|
|
/**
|
|
|
|
* mmc_align_data_size - pads a transfer size to a more optimal value
|
|
|
|
* @card: the MMC card associated with the data transfer
|
|
|
|
* @sz: original transfer size
|
|
|
|
*
|
|
|
|
* Pads the original data size with a number of extra bytes in
|
|
|
|
* order to avoid controller bugs and/or performance hits
|
|
|
|
* (e.g. some controllers revert to PIO for certain sizes).
|
|
|
|
*
|
|
|
|
* Returns the improved size, which might be unmodified.
|
|
|
|
*
|
|
|
|
* Note that this function is only relevant when issuing a
|
|
|
|
* single scatter gather entry.
|
|
|
|
*/
|
|
|
|
unsigned int mmc_align_data_size(struct mmc_card *card, unsigned int sz)
|
|
|
|
{
|
|
|
|
/*
|
|
|
|
* FIXME: We don't have a system for the controller to tell
|
|
|
|
* the core about its problems yet, so for now we just 32-bit
|
|
|
|
* align the size.
|
|
|
|
*/
|
|
|
|
sz = ((sz + 3) / 4) * 4;
|
|
|
|
|
|
|
|
return sz;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_align_data_size);
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
/**
|
2007-06-30 14:21:52 +00:00
|
|
|
* __mmc_claim_host - exclusively claim a host
|
2005-04-16 22:20:36 +00:00
|
|
|
* @host: mmc host to claim
|
2007-06-30 14:21:52 +00:00
|
|
|
* @abort: whether or not the operation should be aborted
|
2005-04-16 22:20:36 +00:00
|
|
|
*
|
2007-06-30 14:21:52 +00:00
|
|
|
* Claim a host for a set of operations. If @abort is non null and
|
|
|
|
* dereference a non-zero value then this will return prematurely with
|
|
|
|
* that non-zero value without acquiring the lock. Returns zero
|
|
|
|
* with the lock held otherwise.
|
2005-04-16 22:20:36 +00:00
|
|
|
*/
|
2007-06-30 14:21:52 +00:00
|
|
|
int __mmc_claim_host(struct mmc_host *host, atomic_t *abort)
|
2005-04-16 22:20:36 +00:00
|
|
|
{
|
|
|
|
DECLARE_WAITQUEUE(wait, current);
|
|
|
|
unsigned long flags;
|
2007-06-30 14:21:52 +00:00
|
|
|
int stop;
|
2015-03-27 11:15:15 +00:00
|
|
|
bool pm = false;
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2007-07-11 18:28:02 +00:00
|
|
|
might_sleep();
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
add_wait_queue(&host->wq, &wait);
|
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
|
|
|
while (1) {
|
|
|
|
set_current_state(TASK_UNINTERRUPTIBLE);
|
2007-06-30 14:21:52 +00:00
|
|
|
stop = abort ? atomic_read(abort) : 0;
|
2009-09-22 23:44:30 +00:00
|
|
|
if (stop || !host->claimed || host->claimer == current)
|
2005-04-16 22:20:36 +00:00
|
|
|
break;
|
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
|
|
|
schedule();
|
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
|
|
|
}
|
|
|
|
set_current_state(TASK_RUNNING);
|
2009-09-22 23:44:30 +00:00
|
|
|
if (!stop) {
|
2007-06-30 14:21:52 +00:00
|
|
|
host->claimed = 1;
|
2009-09-22 23:44:30 +00:00
|
|
|
host->claimer = current;
|
|
|
|
host->claim_cnt += 1;
|
2015-03-27 11:15:15 +00:00
|
|
|
if (host->claim_cnt == 1)
|
|
|
|
pm = true;
|
2009-09-22 23:44:30 +00:00
|
|
|
} else
|
2007-06-30 14:21:52 +00:00
|
|
|
wake_up(&host->wq);
|
2005-04-16 22:20:36 +00:00
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
|
|
|
remove_wait_queue(&host->wq, &wait);
|
2015-03-27 11:15:15 +00:00
|
|
|
|
|
|
|
if (pm)
|
|
|
|
pm_runtime_get_sync(mmc_dev(host));
|
|
|
|
|
2007-06-30 14:21:52 +00:00
|
|
|
return stop;
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
2007-06-30 14:21:52 +00:00
|
|
|
EXPORT_SYMBOL(__mmc_claim_host);
|
2009-09-22 23:44:29 +00:00
|
|
|
|
2011-03-09 08:11:02 +00:00
|
|
|
/**
|
2012-02-29 07:17:21 +00:00
|
|
|
* mmc_release_host - release a host
|
2011-03-09 08:11:02 +00:00
|
|
|
* @host: mmc host to release
|
|
|
|
*
|
2012-02-29 07:17:21 +00:00
|
|
|
* Release a MMC host, allowing others to claim the host
|
|
|
|
* for their operations.
|
2011-03-09 08:11:02 +00:00
|
|
|
*/
|
2012-02-29 07:17:21 +00:00
|
|
|
void mmc_release_host(struct mmc_host *host)
|
2009-09-22 23:44:29 +00:00
|
|
|
{
|
|
|
|
unsigned long flags;
|
|
|
|
|
2012-02-29 07:17:21 +00:00
|
|
|
WARN_ON(!host->claimed);
|
|
|
|
|
2009-09-22 23:44:29 +00:00
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
2009-09-22 23:44:30 +00:00
|
|
|
if (--host->claim_cnt) {
|
|
|
|
/* Release for nested claim */
|
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
|
|
|
} else {
|
|
|
|
host->claimed = 0;
|
|
|
|
host->claimer = NULL;
|
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
|
|
|
wake_up(&host->wq);
|
2015-03-27 11:15:15 +00:00
|
|
|
pm_runtime_mark_last_busy(mmc_dev(host));
|
|
|
|
pm_runtime_put_autosuspend(mmc_dev(host));
|
2009-09-22 23:44:30 +00:00
|
|
|
}
|
2009-09-22 23:44:29 +00:00
|
|
|
}
|
2005-04-16 22:20:36 +00:00
|
|
|
EXPORT_SYMBOL(mmc_release_host);
|
|
|
|
|
2013-05-02 12:02:38 +00:00
|
|
|
/*
|
|
|
|
* This is a helper function, which fetches a runtime pm reference for the
|
|
|
|
* card device and also claims the host.
|
|
|
|
*/
|
|
|
|
void mmc_get_card(struct mmc_card *card)
|
|
|
|
{
|
|
|
|
pm_runtime_get_sync(&card->dev);
|
|
|
|
mmc_claim_host(card->host);
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_get_card);
|
|
|
|
|
|
|
|
/*
|
|
|
|
* This is a helper function, which releases the host and drops the runtime
|
|
|
|
* pm reference for the card device.
|
|
|
|
*/
|
|
|
|
void mmc_put_card(struct mmc_card *card)
|
|
|
|
{
|
|
|
|
mmc_release_host(card->host);
|
|
|
|
pm_runtime_mark_last_busy(&card->dev);
|
|
|
|
pm_runtime_put_autosuspend(&card->dev);
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_put_card);
|
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
/*
|
|
|
|
* Internal function that does the actual ios call to the host driver,
|
|
|
|
* optionally printing some debug output.
|
|
|
|
*/
|
2006-05-04 17:22:51 +00:00
|
|
|
static inline void mmc_set_ios(struct mmc_host *host)
|
|
|
|
{
|
|
|
|
struct mmc_ios *ios = &host->ios;
|
|
|
|
|
2007-02-18 11:07:47 +00:00
|
|
|
pr_debug("%s: clock %uHz busmode %u powermode %u cs %u Vdd %u "
|
|
|
|
"width %u timing %u\n",
|
2006-05-04 17:22:51 +00:00
|
|
|
mmc_hostname(host), ios->clock, ios->bus_mode,
|
|
|
|
ios->power_mode, ios->chip_select, ios->vdd,
|
2007-02-18 11:07:47 +00:00
|
|
|
ios->bus_width, ios->timing);
|
2007-01-04 14:57:32 +00:00
|
|
|
|
2010-11-09 02:36:50 +00:00
|
|
|
if (ios->clock > 0)
|
|
|
|
mmc_set_ungated(host);
|
2006-05-04 17:22:51 +00:00
|
|
|
host->ops->set_ios(host, ios);
|
|
|
|
}
|
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
/*
|
|
|
|
* Control chip select pin on a host.
|
|
|
|
*/
|
2006-12-24 21:46:55 +00:00
|
|
|
void mmc_set_chip_select(struct mmc_host *host, int mode)
|
2005-04-16 22:20:36 +00:00
|
|
|
{
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_hold(host);
|
2006-12-24 21:46:55 +00:00
|
|
|
host->ios.chip_select = mode;
|
|
|
|
mmc_set_ios(host);
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_release(host);
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
/*
|
|
|
|
* Sets the host clock to the highest possible frequency that
|
|
|
|
* is below "hz".
|
|
|
|
*/
|
2011-08-18 12:23:48 +00:00
|
|
|
static void __mmc_set_clock(struct mmc_host *host, unsigned int hz)
|
2006-12-30 23:11:32 +00:00
|
|
|
{
|
2014-09-23 20:00:26 +00:00
|
|
|
WARN_ON(hz && hz < host->f_min);
|
2006-12-30 23:11:32 +00:00
|
|
|
|
|
|
|
if (hz > host->f_max)
|
|
|
|
hz = host->f_max;
|
|
|
|
|
|
|
|
host->ios.clock = hz;
|
|
|
|
mmc_set_ios(host);
|
|
|
|
}
|
|
|
|
|
2011-08-18 12:23:48 +00:00
|
|
|
void mmc_set_clock(struct mmc_host *host, unsigned int hz)
|
|
|
|
{
|
|
|
|
mmc_host_clk_hold(host);
|
|
|
|
__mmc_set_clock(host, hz);
|
|
|
|
mmc_host_clk_release(host);
|
|
|
|
}
|
|
|
|
|
2010-11-09 02:36:50 +00:00
|
|
|
#ifdef CONFIG_MMC_CLKGATE
|
|
|
|
/*
|
|
|
|
* This gates the clock by setting it to 0 Hz.
|
|
|
|
*/
|
|
|
|
void mmc_gate_clock(struct mmc_host *host)
|
|
|
|
{
|
|
|
|
unsigned long flags;
|
|
|
|
|
|
|
|
spin_lock_irqsave(&host->clk_lock, flags);
|
|
|
|
host->clk_old = host->ios.clock;
|
|
|
|
host->ios.clock = 0;
|
|
|
|
host->clk_gated = true;
|
|
|
|
spin_unlock_irqrestore(&host->clk_lock, flags);
|
|
|
|
mmc_set_ios(host);
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* This restores the clock from gating by using the cached
|
|
|
|
* clock value.
|
|
|
|
*/
|
|
|
|
void mmc_ungate_clock(struct mmc_host *host)
|
|
|
|
{
|
|
|
|
/*
|
|
|
|
* We should previously have gated the clock, so the clock shall
|
|
|
|
* be 0 here! The clock may however be 0 during initialization,
|
|
|
|
* when some request operations are performed before setting
|
|
|
|
* the frequency. When ungate is requested in that situation
|
|
|
|
* we just ignore the call.
|
|
|
|
*/
|
|
|
|
if (host->clk_old) {
|
|
|
|
BUG_ON(host->ios.clock);
|
|
|
|
/* This call will also set host->clk_gated to false */
|
2011-08-18 12:23:48 +00:00
|
|
|
__mmc_set_clock(host, host->clk_old);
|
2010-11-09 02:36:50 +00:00
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
void mmc_set_ungated(struct mmc_host *host)
|
|
|
|
{
|
|
|
|
unsigned long flags;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* We've been given a new frequency while the clock is gated,
|
|
|
|
* so make sure we regard this as ungating it.
|
|
|
|
*/
|
|
|
|
spin_lock_irqsave(&host->clk_lock, flags);
|
|
|
|
host->clk_gated = false;
|
|
|
|
spin_unlock_irqrestore(&host->clk_lock, flags);
|
|
|
|
}
|
|
|
|
|
|
|
|
#else
|
|
|
|
void mmc_set_ungated(struct mmc_host *host)
|
|
|
|
{
|
|
|
|
}
|
|
|
|
#endif
|
|
|
|
|
2014-12-05 17:40:59 +00:00
|
|
|
int mmc_execute_tuning(struct mmc_card *card)
|
|
|
|
{
|
|
|
|
struct mmc_host *host = card->host;
|
|
|
|
u32 opcode;
|
|
|
|
int err;
|
|
|
|
|
|
|
|
if (!host->ops->execute_tuning)
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
if (mmc_card_mmc(card))
|
|
|
|
opcode = MMC_SEND_TUNING_BLOCK_HS200;
|
|
|
|
else
|
|
|
|
opcode = MMC_SEND_TUNING_BLOCK;
|
|
|
|
|
|
|
|
mmc_host_clk_hold(host);
|
|
|
|
err = host->ops->execute_tuning(host, opcode);
|
|
|
|
mmc_host_clk_release(host);
|
|
|
|
|
|
|
|
if (err)
|
|
|
|
pr_err("%s: tuning execution failed\n", mmc_hostname(host));
|
2015-05-07 10:10:13 +00:00
|
|
|
else
|
|
|
|
mmc_retune_enable(host);
|
2014-12-05 17:40:59 +00:00
|
|
|
|
|
|
|
return err;
|
|
|
|
}
|
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
/*
|
|
|
|
* Change the bus mode (open drain/push-pull) of a host.
|
|
|
|
*/
|
|
|
|
void mmc_set_bus_mode(struct mmc_host *host, unsigned int mode)
|
|
|
|
{
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_hold(host);
|
2006-12-30 23:11:32 +00:00
|
|
|
host->ios.bus_mode = mode;
|
|
|
|
mmc_set_ios(host);
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_release(host);
|
2006-12-30 23:11:32 +00:00
|
|
|
}
|
|
|
|
|
2010-08-24 10:20:26 +00:00
|
|
|
/*
|
|
|
|
* Change data bus width of a host.
|
|
|
|
*/
|
|
|
|
void mmc_set_bus_width(struct mmc_host *host, unsigned int width)
|
|
|
|
{
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_hold(host);
|
2011-05-13 05:47:18 +00:00
|
|
|
host->ios.bus_width = width;
|
|
|
|
mmc_set_ios(host);
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_release(host);
|
2010-08-24 10:20:26 +00:00
|
|
|
}
|
|
|
|
|
2014-11-06 13:46:54 +00:00
|
|
|
/*
|
|
|
|
* Set initial state after a power cycle or a hw_reset.
|
|
|
|
*/
|
|
|
|
void mmc_set_initial_state(struct mmc_host *host)
|
|
|
|
{
|
2015-05-07 10:10:13 +00:00
|
|
|
mmc_retune_disable(host);
|
|
|
|
|
2014-11-06 13:46:54 +00:00
|
|
|
if (mmc_host_is_spi(host))
|
|
|
|
host->ios.chip_select = MMC_CS_HIGH;
|
|
|
|
else
|
|
|
|
host->ios.chip_select = MMC_CS_DONTCARE;
|
|
|
|
host->ios.bus_mode = MMC_BUSMODE_PUSHPULL;
|
|
|
|
host->ios.bus_width = MMC_BUS_WIDTH_1;
|
|
|
|
host->ios.timing = MMC_TIMING_LEGACY;
|
2015-02-06 12:12:51 +00:00
|
|
|
host->ios.drv_type = 0;
|
2014-11-06 13:46:54 +00:00
|
|
|
|
|
|
|
mmc_set_ios(host);
|
|
|
|
}
|
|
|
|
|
2008-11-26 19:54:17 +00:00
|
|
|
/**
|
|
|
|
* mmc_vdd_to_ocrbitnum - Convert a voltage to the OCR bit number
|
|
|
|
* @vdd: voltage (mV)
|
|
|
|
* @low_bits: prefer low bits in boundary cases
|
|
|
|
*
|
|
|
|
* This function returns the OCR bit number according to the provided @vdd
|
|
|
|
* value. If conversion is not possible a negative errno value returned.
|
|
|
|
*
|
|
|
|
* Depending on the @low_bits flag the function prefers low or high OCR bits
|
|
|
|
* on boundary voltages. For example,
|
|
|
|
* with @low_bits = true, 3300 mV translates to ilog2(MMC_VDD_32_33);
|
|
|
|
* with @low_bits = false, 3300 mV translates to ilog2(MMC_VDD_33_34);
|
|
|
|
*
|
|
|
|
* Any value in the [1951:1999] range translates to the ilog2(MMC_VDD_20_21).
|
|
|
|
*/
|
|
|
|
static int mmc_vdd_to_ocrbitnum(int vdd, bool low_bits)
|
|
|
|
{
|
|
|
|
const int max_bit = ilog2(MMC_VDD_35_36);
|
|
|
|
int bit;
|
|
|
|
|
|
|
|
if (vdd < 1650 || vdd > 3600)
|
|
|
|
return -EINVAL;
|
|
|
|
|
|
|
|
if (vdd >= 1650 && vdd <= 1950)
|
|
|
|
return ilog2(MMC_VDD_165_195);
|
|
|
|
|
|
|
|
if (low_bits)
|
|
|
|
vdd -= 1;
|
|
|
|
|
|
|
|
/* Base 2000 mV, step 100 mV, bit's base 8. */
|
|
|
|
bit = (vdd - 2000) / 100 + 8;
|
|
|
|
if (bit > max_bit)
|
|
|
|
return max_bit;
|
|
|
|
return bit;
|
|
|
|
}
|
|
|
|
|
|
|
|
/**
|
|
|
|
* mmc_vddrange_to_ocrmask - Convert a voltage range to the OCR mask
|
|
|
|
* @vdd_min: minimum voltage value (mV)
|
|
|
|
* @vdd_max: maximum voltage value (mV)
|
|
|
|
*
|
|
|
|
* This function returns the OCR mask bits according to the provided @vdd_min
|
|
|
|
* and @vdd_max values. If conversion is not possible the function returns 0.
|
|
|
|
*
|
|
|
|
* Notes wrt boundary cases:
|
|
|
|
* This function sets the OCR bits for all boundary voltages, for example
|
|
|
|
* [3300:3400] range is translated to MMC_VDD_32_33 | MMC_VDD_33_34 |
|
|
|
|
* MMC_VDD_34_35 mask.
|
|
|
|
*/
|
|
|
|
u32 mmc_vddrange_to_ocrmask(int vdd_min, int vdd_max)
|
|
|
|
{
|
|
|
|
u32 mask = 0;
|
|
|
|
|
|
|
|
if (vdd_max < vdd_min)
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
/* Prefer high bits for the boundary vdd_max values. */
|
|
|
|
vdd_max = mmc_vdd_to_ocrbitnum(vdd_max, false);
|
|
|
|
if (vdd_max < 0)
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
/* Prefer low bits for the boundary vdd_min values. */
|
|
|
|
vdd_min = mmc_vdd_to_ocrbitnum(vdd_min, true);
|
|
|
|
if (vdd_min < 0)
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
/* Fill the mask, from max bit to min bit. */
|
|
|
|
while (vdd_max >= vdd_min)
|
|
|
|
mask |= 1 << vdd_max--;
|
|
|
|
|
|
|
|
return mask;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_vddrange_to_ocrmask);
|
|
|
|
|
2013-08-26 01:19:22 +00:00
|
|
|
#ifdef CONFIG_OF
|
|
|
|
|
|
|
|
/**
|
|
|
|
* mmc_of_parse_voltage - return mask of supported voltages
|
|
|
|
* @np: The device node need to be parsed.
|
|
|
|
* @mask: mask of voltages available for MMC/SD/SDIO
|
|
|
|
*
|
|
|
|
* 1. Return zero on success.
|
|
|
|
* 2. Return negative errno: voltage-range is invalid.
|
|
|
|
*/
|
|
|
|
int mmc_of_parse_voltage(struct device_node *np, u32 *mask)
|
|
|
|
{
|
|
|
|
const u32 *voltage_ranges;
|
|
|
|
int num_ranges, i;
|
|
|
|
|
|
|
|
voltage_ranges = of_get_property(np, "voltage-ranges", &num_ranges);
|
|
|
|
num_ranges = num_ranges / sizeof(*voltage_ranges) / 2;
|
|
|
|
if (!voltage_ranges || !num_ranges) {
|
|
|
|
pr_info("%s: voltage-ranges unspecified\n", np->full_name);
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
|
|
|
|
for (i = 0; i < num_ranges; i++) {
|
|
|
|
const int j = i * 2;
|
|
|
|
u32 ocr_mask;
|
|
|
|
|
|
|
|
ocr_mask = mmc_vddrange_to_ocrmask(
|
|
|
|
be32_to_cpu(voltage_ranges[j]),
|
|
|
|
be32_to_cpu(voltage_ranges[j + 1]));
|
|
|
|
if (!ocr_mask) {
|
|
|
|
pr_err("%s: voltage-range #%d is invalid\n",
|
|
|
|
np->full_name, i);
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
*mask |= ocr_mask;
|
|
|
|
}
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_of_parse_voltage);
|
|
|
|
|
|
|
|
#endif /* CONFIG_OF */
|
|
|
|
|
2014-06-30 09:07:25 +00:00
|
|
|
static int mmc_of_get_func_num(struct device_node *node)
|
|
|
|
{
|
|
|
|
u32 reg;
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
ret = of_property_read_u32(node, "reg", ®);
|
|
|
|
if (ret < 0)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
return reg;
|
|
|
|
}
|
|
|
|
|
|
|
|
struct device_node *mmc_of_find_child_device(struct mmc_host *host,
|
|
|
|
unsigned func_num)
|
|
|
|
{
|
|
|
|
struct device_node *node;
|
|
|
|
|
|
|
|
if (!host->parent || !host->parent->of_node)
|
|
|
|
return NULL;
|
|
|
|
|
|
|
|
for_each_child_of_node(host->parent->of_node, node) {
|
|
|
|
if (mmc_of_get_func_num(node) == func_num)
|
|
|
|
return node;
|
|
|
|
}
|
|
|
|
|
|
|
|
return NULL;
|
|
|
|
}
|
|
|
|
|
2009-03-11 11:30:43 +00:00
|
|
|
#ifdef CONFIG_REGULATOR
|
|
|
|
|
|
|
|
/**
|
|
|
|
* mmc_regulator_get_ocrmask - return mask of supported voltages
|
|
|
|
* @supply: regulator to use
|
|
|
|
*
|
|
|
|
* This returns either a negative errno, or a mask of voltages that
|
|
|
|
* can be provided to MMC/SD/SDIO devices using the specified voltage
|
|
|
|
* regulator. This would normally be called before registering the
|
|
|
|
* MMC host adapter.
|
|
|
|
*/
|
|
|
|
int mmc_regulator_get_ocrmask(struct regulator *supply)
|
|
|
|
{
|
|
|
|
int result = 0;
|
|
|
|
int count;
|
|
|
|
int i;
|
2014-08-14 12:39:00 +00:00
|
|
|
int vdd_uV;
|
|
|
|
int vdd_mV;
|
2009-03-11 11:30:43 +00:00
|
|
|
|
|
|
|
count = regulator_count_voltages(supply);
|
|
|
|
if (count < 0)
|
|
|
|
return count;
|
|
|
|
|
|
|
|
for (i = 0; i < count; i++) {
|
|
|
|
vdd_uV = regulator_list_voltage(supply, i);
|
|
|
|
if (vdd_uV <= 0)
|
|
|
|
continue;
|
|
|
|
|
|
|
|
vdd_mV = vdd_uV / 1000;
|
|
|
|
result |= mmc_vddrange_to_ocrmask(vdd_mV, vdd_mV);
|
|
|
|
}
|
|
|
|
|
2014-08-14 12:39:00 +00:00
|
|
|
if (!result) {
|
|
|
|
vdd_uV = regulator_get_voltage(supply);
|
|
|
|
if (vdd_uV <= 0)
|
|
|
|
return vdd_uV;
|
|
|
|
|
|
|
|
vdd_mV = vdd_uV / 1000;
|
|
|
|
result = mmc_vddrange_to_ocrmask(vdd_mV, vdd_mV);
|
|
|
|
}
|
|
|
|
|
2009-03-11 11:30:43 +00:00
|
|
|
return result;
|
|
|
|
}
|
2012-06-11 13:39:12 +00:00
|
|
|
EXPORT_SYMBOL_GPL(mmc_regulator_get_ocrmask);
|
2009-03-11 11:30:43 +00:00
|
|
|
|
|
|
|
/**
|
|
|
|
* mmc_regulator_set_ocr - set regulator to match host->ios voltage
|
2010-09-29 05:08:27 +00:00
|
|
|
* @mmc: the host to regulate
|
2009-03-11 11:30:43 +00:00
|
|
|
* @supply: regulator to use
|
2010-09-29 05:08:27 +00:00
|
|
|
* @vdd_bit: zero for power off, else a bit number (host->ios.vdd)
|
2009-03-11 11:30:43 +00:00
|
|
|
*
|
|
|
|
* Returns zero on success, else negative errno.
|
|
|
|
*
|
|
|
|
* MMC host drivers may use this to enable or disable a regulator using
|
|
|
|
* a particular supply voltage. This would normally be called from the
|
|
|
|
* set_ios() method.
|
|
|
|
*/
|
2010-09-29 05:08:27 +00:00
|
|
|
int mmc_regulator_set_ocr(struct mmc_host *mmc,
|
|
|
|
struct regulator *supply,
|
|
|
|
unsigned short vdd_bit)
|
2009-03-11 11:30:43 +00:00
|
|
|
{
|
|
|
|
int result = 0;
|
|
|
|
int min_uV, max_uV;
|
|
|
|
|
|
|
|
if (vdd_bit) {
|
|
|
|
int tmp;
|
|
|
|
|
2012-09-19 14:27:04 +00:00
|
|
|
/*
|
|
|
|
* REVISIT mmc_vddrange_to_ocrmask() may have set some
|
2009-03-11 11:30:43 +00:00
|
|
|
* bits this regulator doesn't quite support ... don't
|
|
|
|
* be too picky, most cards and regulators are OK with
|
|
|
|
* a 0.1V range goof (it's a small error percentage).
|
|
|
|
*/
|
|
|
|
tmp = vdd_bit - ilog2(MMC_VDD_165_195);
|
|
|
|
if (tmp == 0) {
|
|
|
|
min_uV = 1650 * 1000;
|
|
|
|
max_uV = 1950 * 1000;
|
|
|
|
} else {
|
|
|
|
min_uV = 1900 * 1000 + tmp * 100 * 1000;
|
|
|
|
max_uV = min_uV + 100 * 1000;
|
|
|
|
}
|
|
|
|
|
2014-08-12 05:05:12 +00:00
|
|
|
result = regulator_set_voltage(supply, min_uV, max_uV);
|
2010-09-29 05:08:27 +00:00
|
|
|
if (result == 0 && !mmc->regulator_enabled) {
|
2009-03-11 11:30:43 +00:00
|
|
|
result = regulator_enable(supply);
|
2010-09-29 05:08:27 +00:00
|
|
|
if (!result)
|
|
|
|
mmc->regulator_enabled = true;
|
|
|
|
}
|
|
|
|
} else if (mmc->regulator_enabled) {
|
2009-03-11 11:30:43 +00:00
|
|
|
result = regulator_disable(supply);
|
2010-09-29 05:08:27 +00:00
|
|
|
if (result == 0)
|
|
|
|
mmc->regulator_enabled = false;
|
2009-03-11 11:30:43 +00:00
|
|
|
}
|
|
|
|
|
2010-09-29 05:08:27 +00:00
|
|
|
if (result)
|
|
|
|
dev_err(mmc_dev(mmc),
|
|
|
|
"could not set regulator OCR (%d)\n", result);
|
2009-03-11 11:30:43 +00:00
|
|
|
return result;
|
|
|
|
}
|
2012-06-11 13:39:12 +00:00
|
|
|
EXPORT_SYMBOL_GPL(mmc_regulator_set_ocr);
|
2009-03-11 11:30:43 +00:00
|
|
|
|
2014-05-06 22:57:01 +00:00
|
|
|
#endif /* CONFIG_REGULATOR */
|
|
|
|
|
2012-06-20 06:28:43 +00:00
|
|
|
int mmc_regulator_get_supply(struct mmc_host *mmc)
|
|
|
|
{
|
|
|
|
struct device *dev = mmc_dev(mmc);
|
|
|
|
int ret;
|
|
|
|
|
2014-05-06 22:57:01 +00:00
|
|
|
mmc->supply.vmmc = devm_regulator_get_optional(dev, "vmmc");
|
2013-07-29 20:58:01 +00:00
|
|
|
mmc->supply.vqmmc = devm_regulator_get_optional(dev, "vqmmc");
|
2012-06-20 06:28:43 +00:00
|
|
|
|
2014-05-06 22:57:01 +00:00
|
|
|
if (IS_ERR(mmc->supply.vmmc)) {
|
|
|
|
if (PTR_ERR(mmc->supply.vmmc) == -EPROBE_DEFER)
|
|
|
|
return -EPROBE_DEFER;
|
|
|
|
dev_info(dev, "No vmmc regulator found\n");
|
|
|
|
} else {
|
|
|
|
ret = mmc_regulator_get_ocrmask(mmc->supply.vmmc);
|
|
|
|
if (ret > 0)
|
|
|
|
mmc->ocr_avail = ret;
|
|
|
|
else
|
|
|
|
dev_warn(dev, "Failed getting OCR mask: %d\n", ret);
|
|
|
|
}
|
2012-06-20 06:28:43 +00:00
|
|
|
|
2014-05-06 22:57:01 +00:00
|
|
|
if (IS_ERR(mmc->supply.vqmmc)) {
|
|
|
|
if (PTR_ERR(mmc->supply.vqmmc) == -EPROBE_DEFER)
|
|
|
|
return -EPROBE_DEFER;
|
|
|
|
dev_info(dev, "No vqmmc regulator found\n");
|
|
|
|
}
|
2012-06-20 06:28:43 +00:00
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL_GPL(mmc_regulator_get_supply);
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
/*
|
|
|
|
* Mask off any voltages we don't support and select
|
|
|
|
* the lowest voltage
|
|
|
|
*/
|
2006-12-30 23:11:32 +00:00
|
|
|
u32 mmc_select_voltage(struct mmc_host *host, u32 ocr)
|
2005-04-16 22:20:36 +00:00
|
|
|
{
|
|
|
|
int bit;
|
|
|
|
|
2013-09-16 10:06:15 +00:00
|
|
|
/*
|
|
|
|
* Sanity check the voltages that the card claims to
|
|
|
|
* support.
|
|
|
|
*/
|
|
|
|
if (ocr & 0x7F) {
|
|
|
|
dev_warn(mmc_dev(host),
|
|
|
|
"card claims to support voltages below defined range\n");
|
|
|
|
ocr &= ~0x7F;
|
|
|
|
}
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
ocr &= host->ocr_avail;
|
2013-09-16 09:28:42 +00:00
|
|
|
if (!ocr) {
|
|
|
|
dev_warn(mmc_dev(host), "no support for card's volts\n");
|
|
|
|
return 0;
|
|
|
|
}
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2013-09-16 09:28:42 +00:00
|
|
|
if (host->caps2 & MMC_CAP2_FULL_PWR_CYCLE) {
|
|
|
|
bit = ffs(ocr) - 1;
|
2006-11-02 18:43:27 +00:00
|
|
|
ocr &= 3 << bit;
|
2013-09-16 09:28:42 +00:00
|
|
|
mmc_power_cycle(host, ocr);
|
2005-04-16 22:20:36 +00:00
|
|
|
} else {
|
2013-09-16 09:28:42 +00:00
|
|
|
bit = fls(ocr) - 1;
|
|
|
|
ocr &= 3 << bit;
|
|
|
|
if (bit != host->ios.vdd)
|
|
|
|
dev_warn(mmc_dev(host), "exceeding card's volts\n");
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
return ocr;
|
|
|
|
}
|
|
|
|
|
2013-01-28 14:08:27 +00:00
|
|
|
int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage)
|
|
|
|
{
|
|
|
|
int err = 0;
|
|
|
|
int old_signal_voltage = host->ios.signal_voltage;
|
|
|
|
|
|
|
|
host->ios.signal_voltage = signal_voltage;
|
|
|
|
if (host->ops->start_signal_voltage_switch) {
|
|
|
|
mmc_host_clk_hold(host);
|
|
|
|
err = host->ops->start_signal_voltage_switch(host, &host->ios);
|
|
|
|
mmc_host_clk_release(host);
|
|
|
|
}
|
|
|
|
|
|
|
|
if (err)
|
|
|
|
host->ios.signal_voltage = old_signal_voltage;
|
|
|
|
|
|
|
|
return err;
|
|
|
|
|
|
|
|
}
|
|
|
|
|
2013-09-12 13:36:34 +00:00
|
|
|
int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, u32 ocr)
|
mmc: sd: add support for signal voltage switch procedure
Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.
Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.
If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-05 06:48:57 +00:00
|
|
|
{
|
|
|
|
struct mmc_command cmd = {0};
|
|
|
|
int err = 0;
|
2013-01-28 14:08:28 +00:00
|
|
|
u32 clock;
|
mmc: sd: add support for signal voltage switch procedure
Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.
Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.
If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-05 06:48:57 +00:00
|
|
|
|
|
|
|
BUG_ON(!host);
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Send CMD11 only if the request is to switch the card to
|
|
|
|
* 1.8V signalling.
|
|
|
|
*/
|
2013-01-28 14:08:28 +00:00
|
|
|
if (signal_voltage == MMC_SIGNAL_VOLTAGE_330)
|
|
|
|
return __mmc_set_signal_voltage(host, signal_voltage);
|
mmc: sd: add support for signal voltage switch procedure
Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.
Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.
If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-05 06:48:57 +00:00
|
|
|
|
2013-01-28 14:08:28 +00:00
|
|
|
/*
|
|
|
|
* If we cannot switch voltages, return failure so the caller
|
|
|
|
* can continue without UHS mode
|
|
|
|
*/
|
|
|
|
if (!host->ops->start_signal_voltage_switch)
|
|
|
|
return -EPERM;
|
|
|
|
if (!host->ops->card_busy)
|
2014-09-12 21:56:56 +00:00
|
|
|
pr_warn("%s: cannot verify signal voltage switch\n",
|
|
|
|
mmc_hostname(host));
|
2013-01-28 14:08:28 +00:00
|
|
|
|
2014-11-21 00:51:40 +00:00
|
|
|
mmc_host_clk_hold(host);
|
|
|
|
|
2013-01-28 14:08:28 +00:00
|
|
|
cmd.opcode = SD_SWITCH_VOLTAGE;
|
|
|
|
cmd.arg = 0;
|
|
|
|
cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
|
|
|
|
|
|
|
|
err = mmc_wait_for_cmd(host, &cmd, 0);
|
|
|
|
if (err)
|
2014-11-21 00:51:40 +00:00
|
|
|
goto err_command;
|
2013-01-28 14:08:28 +00:00
|
|
|
|
2014-11-21 00:51:40 +00:00
|
|
|
if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) {
|
|
|
|
err = -EIO;
|
|
|
|
goto err_command;
|
|
|
|
}
|
2013-01-28 14:08:28 +00:00
|
|
|
/*
|
|
|
|
* The card should drive cmd and dat[0:3] low immediately
|
|
|
|
* after the response of cmd11, but wait 1 ms to be sure
|
|
|
|
*/
|
|
|
|
mmc_delay(1);
|
|
|
|
if (host->ops->card_busy && !host->ops->card_busy(host)) {
|
|
|
|
err = -EAGAIN;
|
|
|
|
goto power_cycle;
|
|
|
|
}
|
|
|
|
/*
|
|
|
|
* During a signal voltage level switch, the clock must be gated
|
|
|
|
* for 5 ms according to the SD spec
|
|
|
|
*/
|
|
|
|
clock = host->ios.clock;
|
|
|
|
host->ios.clock = 0;
|
|
|
|
mmc_set_ios(host);
|
mmc: sd: add support for signal voltage switch procedure
Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.
Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.
If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-05 06:48:57 +00:00
|
|
|
|
2013-01-28 14:08:28 +00:00
|
|
|
if (__mmc_set_signal_voltage(host, signal_voltage)) {
|
|
|
|
/*
|
|
|
|
* Voltages may not have been switched, but we've already
|
|
|
|
* sent CMD11, so a power cycle is required anyway
|
|
|
|
*/
|
|
|
|
err = -EAGAIN;
|
|
|
|
goto power_cycle;
|
mmc: sd: add support for signal voltage switch procedure
Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.
Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.
If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-05 06:48:57 +00:00
|
|
|
}
|
|
|
|
|
2015-05-12 21:46:11 +00:00
|
|
|
/* Keep clock gated for at least 10 ms, though spec only says 5 ms */
|
|
|
|
mmc_delay(10);
|
2013-01-28 14:08:28 +00:00
|
|
|
host->ios.clock = clock;
|
|
|
|
mmc_set_ios(host);
|
|
|
|
|
|
|
|
/* Wait for at least 1 ms according to spec */
|
|
|
|
mmc_delay(1);
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Failure to switch is indicated by the card holding
|
|
|
|
* dat[0:3] low
|
|
|
|
*/
|
|
|
|
if (host->ops->card_busy && host->ops->card_busy(host))
|
|
|
|
err = -EAGAIN;
|
|
|
|
|
|
|
|
power_cycle:
|
|
|
|
if (err) {
|
|
|
|
pr_debug("%s: Signal voltage switch failed, "
|
|
|
|
"power cycling card\n", mmc_hostname(host));
|
2013-09-12 13:36:34 +00:00
|
|
|
mmc_power_cycle(host, ocr);
|
2013-01-28 14:08:28 +00:00
|
|
|
}
|
|
|
|
|
2014-11-21 00:51:40 +00:00
|
|
|
err_command:
|
2013-01-28 14:08:28 +00:00
|
|
|
mmc_host_clk_release(host);
|
|
|
|
|
|
|
|
return err;
|
mmc: sd: add support for signal voltage switch procedure
Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.
Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.
If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-05 06:48:57 +00:00
|
|
|
}
|
|
|
|
|
2005-09-06 22:18:53 +00:00
|
|
|
/*
|
2006-12-30 23:11:32 +00:00
|
|
|
* Select timing parameters for host.
|
2005-09-06 22:18:53 +00:00
|
|
|
*/
|
2006-12-30 23:11:32 +00:00
|
|
|
void mmc_set_timing(struct mmc_host *host, unsigned int timing)
|
2005-09-06 22:18:53 +00:00
|
|
|
{
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_hold(host);
|
2006-12-30 23:11:32 +00:00
|
|
|
host->ios.timing = timing;
|
|
|
|
mmc_set_ios(host);
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_release(host);
|
2005-09-06 22:18:53 +00:00
|
|
|
}
|
|
|
|
|
2011-05-05 06:48:59 +00:00
|
|
|
/*
|
|
|
|
* Select appropriate driver type for host.
|
|
|
|
*/
|
|
|
|
void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type)
|
|
|
|
{
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_hold(host);
|
2011-05-05 06:48:59 +00:00
|
|
|
host->ios.drv_type = drv_type;
|
|
|
|
mmc_set_ios(host);
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_release(host);
|
2011-05-05 06:48:59 +00:00
|
|
|
}
|
|
|
|
|
2015-02-06 12:12:55 +00:00
|
|
|
int mmc_select_drive_strength(struct mmc_card *card, unsigned int max_dtr,
|
|
|
|
int card_drv_type, int *drv_type)
|
|
|
|
{
|
|
|
|
struct mmc_host *host = card->host;
|
|
|
|
int host_drv_type = SD_DRIVER_TYPE_B;
|
|
|
|
int drive_strength;
|
|
|
|
|
|
|
|
*drv_type = 0;
|
|
|
|
|
|
|
|
if (!host->ops->select_drive_strength)
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
/* Use SD definition of driver strength for hosts */
|
|
|
|
if (host->caps & MMC_CAP_DRIVER_TYPE_A)
|
|
|
|
host_drv_type |= SD_DRIVER_TYPE_A;
|
|
|
|
|
|
|
|
if (host->caps & MMC_CAP_DRIVER_TYPE_C)
|
|
|
|
host_drv_type |= SD_DRIVER_TYPE_C;
|
|
|
|
|
|
|
|
if (host->caps & MMC_CAP_DRIVER_TYPE_D)
|
|
|
|
host_drv_type |= SD_DRIVER_TYPE_D;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* The drive strength that the hardware can support
|
|
|
|
* depends on the board design. Pass the appropriate
|
|
|
|
* information and let the hardware specific code
|
|
|
|
* return what is possible given the options
|
|
|
|
*/
|
|
|
|
mmc_host_clk_hold(host);
|
|
|
|
drive_strength = host->ops->select_drive_strength(card, max_dtr,
|
|
|
|
host_drv_type,
|
|
|
|
card_drv_type,
|
|
|
|
drv_type);
|
|
|
|
mmc_host_clk_release(host);
|
|
|
|
|
|
|
|
return drive_strength;
|
|
|
|
}
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
/*
|
2005-12-14 14:57:35 +00:00
|
|
|
* Apply power to the MMC stack. This is a two-stage process.
|
|
|
|
* First, we enable power to the card without the clock running.
|
|
|
|
* We then wait a bit for the power to stabilise. Finally,
|
|
|
|
* enable the bus drivers and clock to the card.
|
|
|
|
*
|
|
|
|
* We must _NOT_ enable the clock prior to power stablising.
|
|
|
|
*
|
|
|
|
* If a host does all the power sequencing itself, ignore the
|
|
|
|
* initial MMC_POWER_UP stage.
|
2005-04-16 22:20:36 +00:00
|
|
|
*/
|
2013-09-12 12:36:53 +00:00
|
|
|
void mmc_power_up(struct mmc_host *host, u32 ocr)
|
2005-04-16 22:20:36 +00:00
|
|
|
{
|
2012-05-09 14:15:26 +00:00
|
|
|
if (host->ios.power_mode == MMC_POWER_ON)
|
|
|
|
return;
|
|
|
|
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_hold(host);
|
|
|
|
|
2014-11-28 13:38:36 +00:00
|
|
|
mmc_pwrseq_pre_power_on(host);
|
|
|
|
|
2013-09-12 12:36:53 +00:00
|
|
|
host->ios.vdd = fls(ocr) - 1;
|
2005-04-16 22:20:36 +00:00
|
|
|
host->ios.power_mode = MMC_POWER_UP;
|
2014-11-06 13:46:54 +00:00
|
|
|
/* Set initial state and call mmc_set_ios */
|
|
|
|
mmc_set_initial_state(host);
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2014-04-24 21:44:26 +00:00
|
|
|
/* Try to set signal voltage to 3.3V but fall back to 1.8v or 1.2v */
|
|
|
|
if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330) == 0)
|
|
|
|
dev_dbg(mmc_dev(host), "Initial signal voltage of 3.3v\n");
|
|
|
|
else if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180) == 0)
|
|
|
|
dev_dbg(mmc_dev(host), "Initial signal voltage of 1.8v\n");
|
|
|
|
else if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120) == 0)
|
|
|
|
dev_dbg(mmc_dev(host), "Initial signal voltage of 1.2v\n");
|
mmc: core: reset signal voltage on power up
Add a call to mmc_set_signal_voltage() to set signal voltage to 3.3v in
mmc_power_up so that we do not need to touch signal voltage setting in
mmc/sd/sdio init functions and rescan function.
For mmc/sd cards, when doing a suspend/resume cycle, consider the unsafe
resume case, the card will lose its power and when powered on again, we
will set signal voltage to 3.3v in mmc_power_up before its resume function
gets called, which will re-init the card.
And for sdio cards, when doing a suspend/resume cycle, consider the unsafe
resume case, the card will either lose its power or not depending on if it
wants to wakeup the host. If power is not maintained, it is the same case as
mmc/sd cards. If power is maintained, mmc_power_up will not be called and
the card's signal voltage will remain at the last setting.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-10 08:55:37 +00:00
|
|
|
|
2007-09-19 16:38:50 +00:00
|
|
|
/*
|
|
|
|
* This delay should be sufficient to allow the power supply
|
|
|
|
* to reach the minimum voltage.
|
|
|
|
*/
|
2009-03-10 01:21:21 +00:00
|
|
|
mmc_delay(10);
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2015-02-02 15:01:14 +00:00
|
|
|
mmc_pwrseq_post_power_on(host);
|
|
|
|
|
2010-09-06 01:37:19 +00:00
|
|
|
host->ios.clock = host->f_init;
|
2009-04-09 06:32:02 +00:00
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
host->ios.power_mode = MMC_POWER_ON;
|
2006-05-04 17:22:51 +00:00
|
|
|
mmc_set_ios(host);
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2007-09-19 16:38:50 +00:00
|
|
|
/*
|
|
|
|
* This delay must be at least 74 clock sizes, or 1 ms, or the
|
|
|
|
* time required to reach a stable voltage.
|
|
|
|
*/
|
2009-03-10 01:21:21 +00:00
|
|
|
mmc_delay(10);
|
2011-08-18 12:23:48 +00:00
|
|
|
|
|
|
|
mmc_host_clk_release(host);
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
|
|
|
|
2011-09-21 18:08:13 +00:00
|
|
|
void mmc_power_off(struct mmc_host *host)
|
2005-04-16 22:20:36 +00:00
|
|
|
{
|
2012-05-09 14:15:26 +00:00
|
|
|
if (host->ios.power_mode == MMC_POWER_OFF)
|
|
|
|
return;
|
|
|
|
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_hold(host);
|
|
|
|
|
2014-11-28 13:38:36 +00:00
|
|
|
mmc_pwrseq_power_off(host);
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
host->ios.clock = 0;
|
|
|
|
host->ios.vdd = 0;
|
2011-03-05 13:36:24 +00:00
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
host->ios.power_mode = MMC_POWER_OFF;
|
2014-11-06 13:46:54 +00:00
|
|
|
/* Set initial state and call mmc_set_ios */
|
|
|
|
mmc_set_initial_state(host);
|
2011-08-18 12:23:48 +00:00
|
|
|
|
2011-09-07 09:22:09 +00:00
|
|
|
/*
|
|
|
|
* Some configurations, such as the 802.11 SDIO card in the OLPC
|
|
|
|
* XO-1.5, require a short delay after poweroff before the card
|
|
|
|
* can be successfully turned on again.
|
|
|
|
*/
|
|
|
|
mmc_delay(1);
|
|
|
|
|
2011-08-18 12:23:48 +00:00
|
|
|
mmc_host_clk_release(host);
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
|
|
|
|
2013-09-12 12:36:53 +00:00
|
|
|
void mmc_power_cycle(struct mmc_host *host, u32 ocr)
|
2013-01-28 14:08:25 +00:00
|
|
|
{
|
|
|
|
mmc_power_off(host);
|
|
|
|
/* Wait at least 1 ms according to SD spec */
|
|
|
|
mmc_delay(1);
|
2013-09-12 12:36:53 +00:00
|
|
|
mmc_power_up(host, ocr);
|
2013-01-28 14:08:25 +00:00
|
|
|
}
|
|
|
|
|
2007-07-24 22:40:58 +00:00
|
|
|
/*
|
|
|
|
* Cleanup when the last reference to the bus operator is dropped.
|
|
|
|
*/
|
2008-04-13 18:15:47 +00:00
|
|
|
static void __mmc_release_bus(struct mmc_host *host)
|
2007-07-24 22:40:58 +00:00
|
|
|
{
|
|
|
|
BUG_ON(!host);
|
|
|
|
BUG_ON(host->bus_refs);
|
|
|
|
BUG_ON(!host->bus_dead);
|
|
|
|
|
|
|
|
host->bus_ops = NULL;
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Increase reference count of bus operator
|
|
|
|
*/
|
|
|
|
static inline void mmc_bus_get(struct mmc_host *host)
|
|
|
|
{
|
|
|
|
unsigned long flags;
|
|
|
|
|
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
|
|
|
host->bus_refs++;
|
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Decrease reference count of bus operator and free it if
|
|
|
|
* it is the last reference.
|
|
|
|
*/
|
|
|
|
static inline void mmc_bus_put(struct mmc_host *host)
|
|
|
|
{
|
|
|
|
unsigned long flags;
|
|
|
|
|
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
|
|
|
host->bus_refs--;
|
|
|
|
if ((host->bus_refs == 0) && host->bus_ops)
|
|
|
|
__mmc_release_bus(host);
|
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
|
|
|
}
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
/*
|
2006-12-30 23:11:32 +00:00
|
|
|
* Assign a mmc bus handler to a host. Only one bus handler may control a
|
|
|
|
* host at any given time.
|
2005-04-16 22:20:36 +00:00
|
|
|
*/
|
2006-12-30 23:11:32 +00:00
|
|
|
void mmc_attach_bus(struct mmc_host *host, const struct mmc_bus_ops *ops)
|
2005-04-16 22:20:36 +00:00
|
|
|
{
|
2006-12-30 23:11:32 +00:00
|
|
|
unsigned long flags;
|
2006-10-29 09:14:19 +00:00
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
BUG_ON(!host);
|
|
|
|
BUG_ON(!ops);
|
2007-01-03 18:47:29 +00:00
|
|
|
|
2007-08-09 11:23:56 +00:00
|
|
|
WARN_ON(!host->claimed);
|
2006-10-21 10:35:02 +00:00
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
2006-10-21 10:35:02 +00:00
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
BUG_ON(host->bus_ops);
|
|
|
|
BUG_ON(host->bus_refs);
|
2005-09-06 22:18:53 +00:00
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
host->bus_ops = ops;
|
|
|
|
host->bus_refs = 1;
|
|
|
|
host->bus_dead = 0;
|
2005-09-06 22:18:53 +00:00
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
2005-09-06 22:18:53 +00:00
|
|
|
}
|
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
/*
|
2011-09-21 18:08:13 +00:00
|
|
|
* Remove the current bus handler from a host.
|
2006-12-30 23:11:32 +00:00
|
|
|
*/
|
|
|
|
void mmc_detach_bus(struct mmc_host *host)
|
2006-11-08 22:03:10 +00:00
|
|
|
{
|
2006-12-30 23:11:32 +00:00
|
|
|
unsigned long flags;
|
2006-11-08 22:03:10 +00:00
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
BUG_ON(!host);
|
2006-11-08 22:03:10 +00:00
|
|
|
|
2007-08-09 11:23:56 +00:00
|
|
|
WARN_ON(!host->claimed);
|
|
|
|
WARN_ON(!host->bus_ops);
|
2007-02-18 11:07:47 +00:00
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
2006-11-08 22:03:10 +00:00
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
host->bus_dead = 1;
|
2006-11-08 22:03:10 +00:00
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
mmc_bus_put(host);
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
|
|
|
|
2013-09-20 09:02:35 +00:00
|
|
|
static void _mmc_detect_change(struct mmc_host *host, unsigned long delay,
|
|
|
|
bool cd_irq)
|
|
|
|
{
|
|
|
|
#ifdef CONFIG_MMC_DEBUG
|
|
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
|
|
|
WARN_ON(host->removed);
|
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
|
|
|
#endif
|
|
|
|
|
|
|
|
/*
|
|
|
|
* If the device is configured as wakeup, we prevent a new sleep for
|
|
|
|
* 5 s to give provision for user space to consume the event.
|
|
|
|
*/
|
|
|
|
if (cd_irq && !(host->caps & MMC_CAP_NEEDS_POLL) &&
|
|
|
|
device_can_wakeup(mmc_dev(host)))
|
|
|
|
pm_wakeup_event(mmc_dev(host), 5000);
|
|
|
|
|
|
|
|
host->detect_change = 1;
|
|
|
|
mmc_schedule_delayed_work(&host->detect, delay);
|
|
|
|
}
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
/**
|
|
|
|
* mmc_detect_change - process change of state on a MMC socket
|
|
|
|
* @host: host which changed state.
|
2005-09-08 16:53:01 +00:00
|
|
|
* @delay: optional delay to wait before detection (jiffies)
|
2005-04-16 22:20:36 +00:00
|
|
|
*
|
2007-07-11 18:22:11 +00:00
|
|
|
* MMC drivers should call this when they detect a card has been
|
|
|
|
* inserted or removed. The MMC layer will confirm that any
|
|
|
|
* present card is still functional, and initialize any newly
|
|
|
|
* inserted.
|
2005-04-16 22:20:36 +00:00
|
|
|
*/
|
2005-09-08 16:53:01 +00:00
|
|
|
void mmc_detect_change(struct mmc_host *host, unsigned long delay)
|
2005-04-16 22:20:36 +00:00
|
|
|
{
|
2013-09-20 09:02:35 +00:00
|
|
|
_mmc_detect_change(host, delay, true);
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_detect_change);
|
|
|
|
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
void mmc_init_erase(struct mmc_card *card)
|
|
|
|
{
|
|
|
|
unsigned int sz;
|
|
|
|
|
|
|
|
if (is_power_of_2(card->erase_size))
|
|
|
|
card->erase_shift = ffs(card->erase_size) - 1;
|
|
|
|
else
|
|
|
|
card->erase_shift = 0;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* It is possible to erase an arbitrarily large area of an SD or MMC
|
|
|
|
* card. That is not desirable because it can take a long time
|
|
|
|
* (minutes) potentially delaying more important I/O, and also the
|
|
|
|
* timeout calculations become increasingly hugely over-estimated.
|
|
|
|
* Consequently, 'pref_erase' is defined as a guide to limit erases
|
|
|
|
* to that size and alignment.
|
|
|
|
*
|
|
|
|
* For SD cards that define Allocation Unit size, limit erases to one
|
|
|
|
* Allocation Unit at a time. For MMC cards that define High Capacity
|
|
|
|
* Erase Size, whether it is switched on or not, limit to that size.
|
|
|
|
* Otherwise just have a stab at a good value. For modern cards it
|
|
|
|
* will end up being 4MiB. Note that if the value is too small, it
|
|
|
|
* can end up taking longer to erase.
|
|
|
|
*/
|
|
|
|
if (mmc_card_sd(card) && card->ssr.au) {
|
|
|
|
card->pref_erase = card->ssr.au;
|
|
|
|
card->erase_shift = ffs(card->ssr.au) - 1;
|
|
|
|
} else if (card->ext_csd.hc_erase_size) {
|
|
|
|
card->pref_erase = card->ext_csd.hc_erase_size;
|
mmc: core: resolve divded by zero panic
With one special SD card, below divide by zero error observed:
...
[ 2.144300] divide error: 0000 [#1] PREEMPT SMP
[ 2.148860] Modules linked in:
[ 2.151898]
[ 2.152685] Set up 4031 stolen pages starting at 0x0001f000, GTT offset 0K
[ 2.157330] Set up 0 CI stolen pages starting at 0x00000000, GTT offset 131072K
[ 2.167581] Pid: 5, comm: kworker/u:0 Not tainted 3.0.8-138216-g974a2ab #1
[ 2.169506] [drm] PSB GTT mem manager ready, tt_start 4031, tt_size 28737 pages
[ 2.169906] [drm] SGX core id = 0x00000000
[ 2.169920] [drm] SGX core rev major = 0x00, minor = 0x00
[ 2.169934] [drm] SGX core rev maintenance = 0x00, designer = 0x00
[ 2.197370] Intel Corporation Medfield/iCDKB
[ 2.201716] EIP: 0060:[<c1697ca6>] EFLAGS: 00010246 CPU: 1
[ 2.207198] EIP is at mmc_init_erase+0x76/0x150
[ 2.211704] EAX: 00002000 EBX: dcd1b400 ECX: 00002000 EDX: 00000000
[ 2.217957] ESI: 00000000 EDI: dcd5c800 EBP: dd867e84 ESP: dd867e7c
[ 2.224214] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 2.229605] Process kworker/u:0 (pid: 5, ti=dd866000 task=dd868000 task.ti=dd866000)
[ 2.237325] Stack:
[ 2.239322] dcd1b400 00000000 dd867eb0 c16a06da c1ab7c44 dd995aa8 00000003 00000000
[ 2.247054] 00000000 00000000 dcd5c800 00000000 dcd1b400 dd867ef8 c16a1012 c1698b00
[ 2.254785] 00000029 00000001 c194eb80 dcd5c9ec dd867e00 c1239b00 00000000 00000000
[ 2.262519] Call Trace:
[ 2.264975] [<c16a06da>] mmc_sd_setup_card+0x1da/0x4f0
[ 2.270183] [<c16a1012>] mmc_sd_init_card+0x192/0xc40
[ 2.275304] [<c1698b00>] ? __mmc_claim_host+0x160/0x160
[ 2.280610] [<c1239b00>] ? __schedule_bug+0x50/0x80
[ 2.285556] [<c16a1b89>] mmc_attach_sd+0xc9/0x230
[ 2.290333] [<c169b6ef>] mmc_rescan+0x25f/0x2c0
[ 2.294943] [<c1274223>] process_one_work+0x103/0x400
[ 2.300065] [<c12670fd>] ? mod_timer+0x1ad/0x3c0
[ 2.304756] [<c169b490>] ? mmc_suspend_host+0x1a0/0x1a0
[ 2.310056] [<c127502d>] worker_thread+0x12d/0x4a0
[ 2.314921] [<c18fcfbd>] ? preempt_schedule+0x2d/0x50
[ 2.320047] [<c1274f00[ 2.323976] ---[ end trace 5398ec2720494438 ]---
...
So, seems this bad SD card does not set valid value in related SSR / CSD register fields.
And then the driver will set card->erase_size to 0.
Then it triggered this divided by zero error when calculate card->pref_erase.
Submit this patch to fix the issue.
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-08-14 10:29:24 +00:00
|
|
|
} else if (card->erase_size) {
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
sz = (card->csd.capacity << (card->csd.read_blkbits - 9)) >> 11;
|
|
|
|
if (sz < 128)
|
|
|
|
card->pref_erase = 512 * 1024 / 512;
|
|
|
|
else if (sz < 512)
|
|
|
|
card->pref_erase = 1024 * 1024 / 512;
|
|
|
|
else if (sz < 1024)
|
|
|
|
card->pref_erase = 2 * 1024 * 1024 / 512;
|
|
|
|
else
|
|
|
|
card->pref_erase = 4 * 1024 * 1024 / 512;
|
|
|
|
if (card->pref_erase < card->erase_size)
|
|
|
|
card->pref_erase = card->erase_size;
|
|
|
|
else {
|
|
|
|
sz = card->pref_erase % card->erase_size;
|
|
|
|
if (sz)
|
|
|
|
card->pref_erase += card->erase_size - sz;
|
|
|
|
}
|
mmc: core: resolve divded by zero panic
With one special SD card, below divide by zero error observed:
...
[ 2.144300] divide error: 0000 [#1] PREEMPT SMP
[ 2.148860] Modules linked in:
[ 2.151898]
[ 2.152685] Set up 4031 stolen pages starting at 0x0001f000, GTT offset 0K
[ 2.157330] Set up 0 CI stolen pages starting at 0x00000000, GTT offset 131072K
[ 2.167581] Pid: 5, comm: kworker/u:0 Not tainted 3.0.8-138216-g974a2ab #1
[ 2.169506] [drm] PSB GTT mem manager ready, tt_start 4031, tt_size 28737 pages
[ 2.169906] [drm] SGX core id = 0x00000000
[ 2.169920] [drm] SGX core rev major = 0x00, minor = 0x00
[ 2.169934] [drm] SGX core rev maintenance = 0x00, designer = 0x00
[ 2.197370] Intel Corporation Medfield/iCDKB
[ 2.201716] EIP: 0060:[<c1697ca6>] EFLAGS: 00010246 CPU: 1
[ 2.207198] EIP is at mmc_init_erase+0x76/0x150
[ 2.211704] EAX: 00002000 EBX: dcd1b400 ECX: 00002000 EDX: 00000000
[ 2.217957] ESI: 00000000 EDI: dcd5c800 EBP: dd867e84 ESP: dd867e7c
[ 2.224214] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 2.229605] Process kworker/u:0 (pid: 5, ti=dd866000 task=dd868000 task.ti=dd866000)
[ 2.237325] Stack:
[ 2.239322] dcd1b400 00000000 dd867eb0 c16a06da c1ab7c44 dd995aa8 00000003 00000000
[ 2.247054] 00000000 00000000 dcd5c800 00000000 dcd1b400 dd867ef8 c16a1012 c1698b00
[ 2.254785] 00000029 00000001 c194eb80 dcd5c9ec dd867e00 c1239b00 00000000 00000000
[ 2.262519] Call Trace:
[ 2.264975] [<c16a06da>] mmc_sd_setup_card+0x1da/0x4f0
[ 2.270183] [<c16a1012>] mmc_sd_init_card+0x192/0xc40
[ 2.275304] [<c1698b00>] ? __mmc_claim_host+0x160/0x160
[ 2.280610] [<c1239b00>] ? __schedule_bug+0x50/0x80
[ 2.285556] [<c16a1b89>] mmc_attach_sd+0xc9/0x230
[ 2.290333] [<c169b6ef>] mmc_rescan+0x25f/0x2c0
[ 2.294943] [<c1274223>] process_one_work+0x103/0x400
[ 2.300065] [<c12670fd>] ? mod_timer+0x1ad/0x3c0
[ 2.304756] [<c169b490>] ? mmc_suspend_host+0x1a0/0x1a0
[ 2.310056] [<c127502d>] worker_thread+0x12d/0x4a0
[ 2.314921] [<c18fcfbd>] ? preempt_schedule+0x2d/0x50
[ 2.320047] [<c1274f00[ 2.323976] ---[ end trace 5398ec2720494438 ]---
...
So, seems this bad SD card does not set valid value in related SSR / CSD register fields.
And then the driver will set card->erase_size to 0.
Then it triggered this divided by zero error when calculate card->pref_erase.
Submit this patch to fix the issue.
Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-08-14 10:29:24 +00:00
|
|
|
} else
|
|
|
|
card->pref_erase = 0;
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
}
|
|
|
|
|
2011-04-11 21:13:41 +00:00
|
|
|
static unsigned int mmc_mmc_erase_timeout(struct mmc_card *card,
|
|
|
|
unsigned int arg, unsigned int qty)
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
{
|
|
|
|
unsigned int erase_timeout;
|
|
|
|
|
2012-04-05 11:45:47 +00:00
|
|
|
if (arg == MMC_DISCARD_ARG ||
|
|
|
|
(arg == MMC_TRIM_ARG && card->ext_csd.rev >= 6)) {
|
|
|
|
erase_timeout = card->ext_csd.trim_timeout;
|
|
|
|
} else if (card->ext_csd.erase_group_def & 1) {
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
/* High Capacity Erase Group Size uses HC timeouts */
|
|
|
|
if (arg == MMC_TRIM_ARG)
|
|
|
|
erase_timeout = card->ext_csd.trim_timeout;
|
|
|
|
else
|
|
|
|
erase_timeout = card->ext_csd.hc_erase_timeout;
|
|
|
|
} else {
|
|
|
|
/* CSD Erase Group Size uses write timeout */
|
|
|
|
unsigned int mult = (10 << card->csd.r2w_factor);
|
|
|
|
unsigned int timeout_clks = card->csd.tacc_clks * mult;
|
|
|
|
unsigned int timeout_us;
|
|
|
|
|
|
|
|
/* Avoid overflow: e.g. tacc_ns=80000000 mult=1280 */
|
|
|
|
if (card->csd.tacc_ns < 1000000)
|
|
|
|
timeout_us = (card->csd.tacc_ns * mult) / 1000;
|
|
|
|
else
|
|
|
|
timeout_us = (card->csd.tacc_ns / 1000) * mult;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* ios.clock is only a target. The real clock rate might be
|
|
|
|
* less but not that much less, so fudge it by multiplying by 2.
|
|
|
|
*/
|
|
|
|
timeout_clks <<= 1;
|
|
|
|
timeout_us += (timeout_clks * 1000) /
|
2011-06-23 10:40:27 +00:00
|
|
|
(mmc_host_clk_rate(card->host) / 1000);
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
|
|
|
|
erase_timeout = timeout_us / 1000;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Theoretically, the calculation could underflow so round up
|
|
|
|
* to 1ms in that case.
|
|
|
|
*/
|
|
|
|
if (!erase_timeout)
|
|
|
|
erase_timeout = 1;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Multiplier for secure operations */
|
|
|
|
if (arg & MMC_SECURE_ARGS) {
|
|
|
|
if (arg == MMC_SECURE_ERASE_ARG)
|
|
|
|
erase_timeout *= card->ext_csd.sec_erase_mult;
|
|
|
|
else
|
|
|
|
erase_timeout *= card->ext_csd.sec_trim_mult;
|
|
|
|
}
|
|
|
|
|
|
|
|
erase_timeout *= qty;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Ensure at least a 1 second timeout for SPI as per
|
|
|
|
* 'mmc_set_data_timeout()'
|
|
|
|
*/
|
|
|
|
if (mmc_host_is_spi(card->host) && erase_timeout < 1000)
|
|
|
|
erase_timeout = 1000;
|
|
|
|
|
2011-04-11 21:13:41 +00:00
|
|
|
return erase_timeout;
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
}
|
|
|
|
|
2011-04-11 21:13:41 +00:00
|
|
|
static unsigned int mmc_sd_erase_timeout(struct mmc_card *card,
|
|
|
|
unsigned int arg,
|
|
|
|
unsigned int qty)
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
{
|
2011-04-11 21:13:41 +00:00
|
|
|
unsigned int erase_timeout;
|
|
|
|
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
if (card->ssr.erase_timeout) {
|
|
|
|
/* Erase timeout specified in SD Status Register (SSR) */
|
2011-04-11 21:13:41 +00:00
|
|
|
erase_timeout = card->ssr.erase_timeout * qty +
|
|
|
|
card->ssr.erase_offset;
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
} else {
|
|
|
|
/*
|
|
|
|
* Erase timeout not specified in SD Status Register (SSR) so
|
|
|
|
* use 250ms per write block.
|
|
|
|
*/
|
2011-04-11 21:13:41 +00:00
|
|
|
erase_timeout = 250 * qty;
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
/* Must not be less than 1 second */
|
2011-04-11 21:13:41 +00:00
|
|
|
if (erase_timeout < 1000)
|
|
|
|
erase_timeout = 1000;
|
|
|
|
|
|
|
|
return erase_timeout;
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
}
|
|
|
|
|
2011-04-11 21:13:41 +00:00
|
|
|
static unsigned int mmc_erase_timeout(struct mmc_card *card,
|
|
|
|
unsigned int arg,
|
|
|
|
unsigned int qty)
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
{
|
|
|
|
if (mmc_card_sd(card))
|
2011-04-11 21:13:41 +00:00
|
|
|
return mmc_sd_erase_timeout(card, arg, qty);
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
else
|
2011-04-11 21:13:41 +00:00
|
|
|
return mmc_mmc_erase_timeout(card, arg, qty);
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
static int mmc_do_erase(struct mmc_card *card, unsigned int from,
|
|
|
|
unsigned int to, unsigned int arg)
|
|
|
|
{
|
2011-04-14 03:40:30 +00:00
|
|
|
struct mmc_command cmd = {0};
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
unsigned int qty = 0;
|
2012-11-16 15:31:41 +00:00
|
|
|
unsigned long timeout;
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
int err;
|
|
|
|
|
2015-05-07 10:10:16 +00:00
|
|
|
mmc_retune_hold(card->host);
|
|
|
|
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
/*
|
|
|
|
* qty is used to calculate the erase timeout which depends on how many
|
|
|
|
* erase groups (or allocation units in SD terminology) are affected.
|
|
|
|
* We count erasing part of an erase group as one erase group.
|
|
|
|
* For SD, the allocation units are always a power of 2. For MMC, the
|
|
|
|
* erase group size is almost certainly also power of 2, but it does not
|
|
|
|
* seem to insist on that in the JEDEC standard, so we fall back to
|
|
|
|
* division in that case. SD may not specify an allocation unit size,
|
|
|
|
* in which case the timeout is based on the number of write blocks.
|
|
|
|
*
|
|
|
|
* Note that the timeout for secure trim 2 will only be correct if the
|
|
|
|
* number of erase groups specified is the same as the total of all
|
|
|
|
* preceding secure trim 1 commands. Since the power may have been
|
|
|
|
* lost since the secure trim 1 commands occurred, it is generally
|
|
|
|
* impossible to calculate the secure trim 2 timeout correctly.
|
|
|
|
*/
|
|
|
|
if (card->erase_shift)
|
|
|
|
qty += ((to >> card->erase_shift) -
|
|
|
|
(from >> card->erase_shift)) + 1;
|
|
|
|
else if (mmc_card_sd(card))
|
|
|
|
qty += to - from + 1;
|
|
|
|
else
|
|
|
|
qty += ((to / card->erase_size) -
|
|
|
|
(from / card->erase_size)) + 1;
|
|
|
|
|
|
|
|
if (!mmc_card_blockaddr(card)) {
|
|
|
|
from <<= 9;
|
|
|
|
to <<= 9;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (mmc_card_sd(card))
|
|
|
|
cmd.opcode = SD_ERASE_WR_BLK_START;
|
|
|
|
else
|
|
|
|
cmd.opcode = MMC_ERASE_GROUP_START;
|
|
|
|
cmd.arg = from;
|
|
|
|
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
|
|
|
|
err = mmc_wait_for_cmd(card->host, &cmd, 0);
|
|
|
|
if (err) {
|
2011-10-11 06:14:09 +00:00
|
|
|
pr_err("mmc_erase: group start error %d, "
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
"status %#x\n", err, cmd.resp[0]);
|
2011-08-29 13:42:15 +00:00
|
|
|
err = -EIO;
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
goto out;
|
|
|
|
}
|
|
|
|
|
|
|
|
memset(&cmd, 0, sizeof(struct mmc_command));
|
|
|
|
if (mmc_card_sd(card))
|
|
|
|
cmd.opcode = SD_ERASE_WR_BLK_END;
|
|
|
|
else
|
|
|
|
cmd.opcode = MMC_ERASE_GROUP_END;
|
|
|
|
cmd.arg = to;
|
|
|
|
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
|
|
|
|
err = mmc_wait_for_cmd(card->host, &cmd, 0);
|
|
|
|
if (err) {
|
2011-10-11 06:14:09 +00:00
|
|
|
pr_err("mmc_erase: group end error %d, status %#x\n",
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
err, cmd.resp[0]);
|
2011-08-29 13:42:15 +00:00
|
|
|
err = -EIO;
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
goto out;
|
|
|
|
}
|
|
|
|
|
|
|
|
memset(&cmd, 0, sizeof(struct mmc_command));
|
|
|
|
cmd.opcode = MMC_ERASE;
|
|
|
|
cmd.arg = arg;
|
|
|
|
cmd.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC;
|
2014-01-08 14:06:08 +00:00
|
|
|
cmd.busy_timeout = mmc_erase_timeout(card, arg, qty);
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
err = mmc_wait_for_cmd(card->host, &cmd, 0);
|
|
|
|
if (err) {
|
2011-10-11 06:14:09 +00:00
|
|
|
pr_err("mmc_erase: erase error %d, status %#x\n",
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
err, cmd.resp[0]);
|
|
|
|
err = -EIO;
|
|
|
|
goto out;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (mmc_host_is_spi(card->host))
|
|
|
|
goto out;
|
|
|
|
|
2012-11-16 15:31:41 +00:00
|
|
|
timeout = jiffies + msecs_to_jiffies(MMC_CORE_TIMEOUT_MS);
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
do {
|
|
|
|
memset(&cmd, 0, sizeof(struct mmc_command));
|
|
|
|
cmd.opcode = MMC_SEND_STATUS;
|
|
|
|
cmd.arg = card->rca << 16;
|
|
|
|
cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
|
|
|
|
/* Do not retry else we can't see errors */
|
|
|
|
err = mmc_wait_for_cmd(card->host, &cmd, 0);
|
|
|
|
if (err || (cmd.resp[0] & 0xFDF92000)) {
|
2011-10-11 06:14:09 +00:00
|
|
|
pr_err("error %d requesting status %#x\n",
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
err, cmd.resp[0]);
|
|
|
|
err = -EIO;
|
|
|
|
goto out;
|
|
|
|
}
|
2012-11-16 15:31:41 +00:00
|
|
|
|
|
|
|
/* Timeout if the device never becomes ready for data and
|
|
|
|
* never leaves the program state.
|
|
|
|
*/
|
|
|
|
if (time_after(jiffies, timeout)) {
|
|
|
|
pr_err("%s: Card stuck in programming state! %s\n",
|
|
|
|
mmc_hostname(card->host), __func__);
|
|
|
|
err = -EIO;
|
|
|
|
goto out;
|
|
|
|
}
|
|
|
|
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
} while (!(cmd.resp[0] & R1_READY_FOR_DATA) ||
|
2012-11-16 15:31:41 +00:00
|
|
|
(R1_CURRENT_STATE(cmd.resp[0]) == R1_STATE_PRG));
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
out:
|
2015-05-07 10:10:16 +00:00
|
|
|
mmc_retune_release(card->host);
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
return err;
|
|
|
|
}
|
|
|
|
|
|
|
|
/**
|
|
|
|
* mmc_erase - erase sectors.
|
|
|
|
* @card: card to erase
|
|
|
|
* @from: first sector to erase
|
|
|
|
* @nr: number of sectors to erase
|
|
|
|
* @arg: erase command argument (SD supports only %MMC_ERASE_ARG)
|
|
|
|
*
|
|
|
|
* Caller must claim host before calling this function.
|
|
|
|
*/
|
|
|
|
int mmc_erase(struct mmc_card *card, unsigned int from, unsigned int nr,
|
|
|
|
unsigned int arg)
|
|
|
|
{
|
|
|
|
unsigned int rem, to = from + nr;
|
2015-06-23 09:43:52 +00:00
|
|
|
int err;
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
|
|
|
|
if (!(card->host->caps & MMC_CAP_ERASE) ||
|
|
|
|
!(card->csd.cmdclass & CCC_ERASE))
|
|
|
|
return -EOPNOTSUPP;
|
|
|
|
|
|
|
|
if (!card->erase_size)
|
|
|
|
return -EOPNOTSUPP;
|
|
|
|
|
|
|
|
if (mmc_card_sd(card) && arg != MMC_ERASE_ARG)
|
|
|
|
return -EOPNOTSUPP;
|
|
|
|
|
|
|
|
if ((arg & MMC_SECURE_ARGS) &&
|
|
|
|
!(card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN))
|
|
|
|
return -EOPNOTSUPP;
|
|
|
|
|
|
|
|
if ((arg & MMC_TRIM_ARGS) &&
|
|
|
|
!(card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN))
|
|
|
|
return -EOPNOTSUPP;
|
|
|
|
|
|
|
|
if (arg == MMC_SECURE_ERASE_ARG) {
|
|
|
|
if (from % card->erase_size || nr % card->erase_size)
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (arg == MMC_ERASE_ARG) {
|
|
|
|
rem = from % card->erase_size;
|
|
|
|
if (rem) {
|
|
|
|
rem = card->erase_size - rem;
|
|
|
|
from += rem;
|
|
|
|
if (nr > rem)
|
|
|
|
nr -= rem;
|
|
|
|
else
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
rem = nr % card->erase_size;
|
|
|
|
if (rem)
|
|
|
|
nr -= rem;
|
|
|
|
}
|
|
|
|
|
|
|
|
if (nr == 0)
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
to = from + nr;
|
|
|
|
|
|
|
|
if (to <= from)
|
|
|
|
return -EINVAL;
|
|
|
|
|
|
|
|
/* 'from' and 'to' are inclusive */
|
|
|
|
to -= 1;
|
|
|
|
|
2015-06-23 09:43:52 +00:00
|
|
|
/*
|
|
|
|
* Special case where only one erase-group fits in the timeout budget:
|
|
|
|
* If the region crosses an erase-group boundary on this particular
|
|
|
|
* case, we will be trimming more than one erase-group which, does not
|
|
|
|
* fit in the timeout budget of the controller, so we need to split it
|
|
|
|
* and call mmc_do_erase() twice if necessary. This special case is
|
|
|
|
* identified by the card->eg_boundary flag.
|
|
|
|
*/
|
2015-08-04 06:58:33 +00:00
|
|
|
rem = card->erase_size - (from % card->erase_size);
|
|
|
|
if ((arg & MMC_TRIM_ARGS) && (card->eg_boundary) && (nr > rem)) {
|
2015-06-23 09:43:52 +00:00
|
|
|
err = mmc_do_erase(card, from, from + rem - 1, arg);
|
|
|
|
from += rem;
|
|
|
|
if ((err) || (to <= from))
|
|
|
|
return err;
|
|
|
|
}
|
|
|
|
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
return mmc_do_erase(card, from, to, arg);
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_erase);
|
|
|
|
|
|
|
|
int mmc_can_erase(struct mmc_card *card)
|
|
|
|
{
|
|
|
|
if ((card->host->caps & MMC_CAP_ERASE) &&
|
|
|
|
(card->csd.cmdclass & CCC_ERASE) && card->erase_size)
|
|
|
|
return 1;
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_can_erase);
|
|
|
|
|
|
|
|
int mmc_can_trim(struct mmc_card *card)
|
|
|
|
{
|
2015-08-12 05:08:32 +00:00
|
|
|
if ((card->ext_csd.sec_feature_support & EXT_CSD_SEC_GB_CL_EN) &&
|
|
|
|
(!(card->quirks & MMC_QUIRK_TRIM_BROKEN)))
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
return 1;
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_can_trim);
|
|
|
|
|
2011-10-18 00:34:04 +00:00
|
|
|
int mmc_can_discard(struct mmc_card *card)
|
|
|
|
{
|
|
|
|
/*
|
|
|
|
* As there's no way to detect the discard support bit at v4.5
|
|
|
|
* use the s/w feature support filed.
|
|
|
|
*/
|
|
|
|
if (card->ext_csd.feature_support & MMC_DISCARD_FEATURE)
|
|
|
|
return 1;
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_can_discard);
|
|
|
|
|
2011-10-14 05:15:48 +00:00
|
|
|
int mmc_can_sanitize(struct mmc_card *card)
|
|
|
|
{
|
2012-04-05 11:45:48 +00:00
|
|
|
if (!mmc_can_trim(card) && !mmc_can_erase(card))
|
|
|
|
return 0;
|
2011-10-14 05:15:48 +00:00
|
|
|
if (card->ext_csd.sec_feature_support & EXT_CSD_SEC_SANITIZE)
|
|
|
|
return 1;
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_can_sanitize);
|
|
|
|
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
int mmc_can_secure_erase_trim(struct mmc_card *card)
|
|
|
|
{
|
2014-06-18 11:18:07 +00:00
|
|
|
if ((card->ext_csd.sec_feature_support & EXT_CSD_SEC_ER_EN) &&
|
|
|
|
!(card->quirks & MMC_QUIRK_SEC_ERASE_TRIM_BROKEN))
|
mmc: add erase, secure erase, trim and secure trim operations
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 21:17:46 +00:00
|
|
|
return 1;
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_can_secure_erase_trim);
|
|
|
|
|
|
|
|
int mmc_erase_group_aligned(struct mmc_card *card, unsigned int from,
|
|
|
|
unsigned int nr)
|
|
|
|
{
|
|
|
|
if (!card->erase_size)
|
|
|
|
return 0;
|
|
|
|
if (from % card->erase_size || nr % card->erase_size)
|
|
|
|
return 0;
|
|
|
|
return 1;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_erase_group_aligned);
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2011-06-28 14:16:02 +00:00
|
|
|
static unsigned int mmc_do_calc_max_discard(struct mmc_card *card,
|
|
|
|
unsigned int arg)
|
|
|
|
{
|
|
|
|
struct mmc_host *host = card->host;
|
|
|
|
unsigned int max_discard, x, y, qty = 0, max_qty, timeout;
|
|
|
|
unsigned int last_timeout = 0;
|
|
|
|
|
|
|
|
if (card->erase_shift)
|
|
|
|
max_qty = UINT_MAX >> card->erase_shift;
|
|
|
|
else if (mmc_card_sd(card))
|
|
|
|
max_qty = UINT_MAX;
|
|
|
|
else
|
|
|
|
max_qty = UINT_MAX / card->erase_size;
|
|
|
|
|
|
|
|
/* Find the largest qty with an OK timeout */
|
|
|
|
do {
|
|
|
|
y = 0;
|
|
|
|
for (x = 1; x && x <= max_qty && max_qty - x >= qty; x <<= 1) {
|
|
|
|
timeout = mmc_erase_timeout(card, arg, qty + x);
|
2013-12-18 08:57:38 +00:00
|
|
|
if (timeout > host->max_busy_timeout)
|
2011-06-28 14:16:02 +00:00
|
|
|
break;
|
|
|
|
if (timeout < last_timeout)
|
|
|
|
break;
|
|
|
|
last_timeout = timeout;
|
|
|
|
y = x;
|
|
|
|
}
|
|
|
|
qty += y;
|
|
|
|
} while (y);
|
|
|
|
|
|
|
|
if (!qty)
|
|
|
|
return 0;
|
|
|
|
|
2015-06-23 09:43:52 +00:00
|
|
|
/*
|
|
|
|
* When specifying a sector range to trim, chances are we might cross
|
|
|
|
* an erase-group boundary even if the amount of sectors is less than
|
|
|
|
* one erase-group.
|
|
|
|
* If we can only fit one erase-group in the controller timeout budget,
|
|
|
|
* we have to care that erase-group boundaries are not crossed by a
|
|
|
|
* single trim operation. We flag that special case with "eg_boundary".
|
|
|
|
* In all other cases we can just decrement qty and pretend that we
|
|
|
|
* always touch (qty + 1) erase-groups as a simple optimization.
|
|
|
|
*/
|
2011-06-28 14:16:02 +00:00
|
|
|
if (qty == 1)
|
2015-06-23 09:43:52 +00:00
|
|
|
card->eg_boundary = 1;
|
|
|
|
else
|
|
|
|
qty--;
|
2011-06-28 14:16:02 +00:00
|
|
|
|
|
|
|
/* Convert qty to sectors */
|
|
|
|
if (card->erase_shift)
|
2015-06-23 09:43:52 +00:00
|
|
|
max_discard = qty << card->erase_shift;
|
2011-06-28 14:16:02 +00:00
|
|
|
else if (mmc_card_sd(card))
|
2015-06-23 09:43:52 +00:00
|
|
|
max_discard = qty + 1;
|
2011-06-28 14:16:02 +00:00
|
|
|
else
|
2015-06-23 09:43:52 +00:00
|
|
|
max_discard = qty * card->erase_size;
|
2011-06-28 14:16:02 +00:00
|
|
|
|
|
|
|
return max_discard;
|
|
|
|
}
|
|
|
|
|
|
|
|
unsigned int mmc_calc_max_discard(struct mmc_card *card)
|
|
|
|
{
|
|
|
|
struct mmc_host *host = card->host;
|
|
|
|
unsigned int max_discard, max_trim;
|
|
|
|
|
2013-12-18 08:57:38 +00:00
|
|
|
if (!host->max_busy_timeout)
|
2011-06-28 14:16:02 +00:00
|
|
|
return UINT_MAX;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Without erase_group_def set, MMC erase timeout depends on clock
|
|
|
|
* frequence which can change. In that case, the best choice is
|
|
|
|
* just the preferred erase size.
|
|
|
|
*/
|
|
|
|
if (mmc_card_mmc(card) && !(card->ext_csd.erase_group_def & 1))
|
|
|
|
return card->pref_erase;
|
|
|
|
|
|
|
|
max_discard = mmc_do_calc_max_discard(card, MMC_ERASE_ARG);
|
|
|
|
if (mmc_can_trim(card)) {
|
|
|
|
max_trim = mmc_do_calc_max_discard(card, MMC_TRIM_ARG);
|
|
|
|
if (max_trim < max_discard)
|
|
|
|
max_discard = max_trim;
|
|
|
|
} else if (max_discard < card->erase_size) {
|
|
|
|
max_discard = 0;
|
|
|
|
}
|
|
|
|
pr_debug("%s: calculated max. discard sectors %u for timeout %u ms\n",
|
2013-12-18 08:57:38 +00:00
|
|
|
mmc_hostname(host), max_discard, host->max_busy_timeout);
|
2011-06-28 14:16:02 +00:00
|
|
|
return max_discard;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_calc_max_discard);
|
|
|
|
|
2010-08-24 10:20:26 +00:00
|
|
|
int mmc_set_blocklen(struct mmc_card *card, unsigned int blocklen)
|
|
|
|
{
|
2011-04-14 03:40:30 +00:00
|
|
|
struct mmc_command cmd = {0};
|
2010-08-24 10:20:26 +00:00
|
|
|
|
2014-04-23 08:07:35 +00:00
|
|
|
if (mmc_card_blockaddr(card) || mmc_card_ddr52(card))
|
2010-08-24 10:20:26 +00:00
|
|
|
return 0;
|
|
|
|
|
|
|
|
cmd.opcode = MMC_SET_BLOCKLEN;
|
|
|
|
cmd.arg = blocklen;
|
|
|
|
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
|
|
|
|
return mmc_wait_for_cmd(card->host, &cmd, 5);
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_set_blocklen);
|
|
|
|
|
2012-08-06 15:12:30 +00:00
|
|
|
int mmc_set_blockcount(struct mmc_card *card, unsigned int blockcount,
|
|
|
|
bool is_rel_write)
|
|
|
|
{
|
|
|
|
struct mmc_command cmd = {0};
|
|
|
|
|
|
|
|
cmd.opcode = MMC_SET_BLOCK_COUNT;
|
|
|
|
cmd.arg = blockcount & 0x0000FFFF;
|
|
|
|
if (is_rel_write)
|
|
|
|
cmd.arg |= 1 << 31;
|
|
|
|
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC;
|
|
|
|
return mmc_wait_for_cmd(card->host, &cmd, 5);
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_set_blockcount);
|
|
|
|
|
2011-08-29 13:42:11 +00:00
|
|
|
static void mmc_hw_reset_for_init(struct mmc_host *host)
|
|
|
|
{
|
|
|
|
if (!(host->caps & MMC_CAP_HW_RESET) || !host->ops->hw_reset)
|
|
|
|
return;
|
|
|
|
mmc_host_clk_hold(host);
|
|
|
|
host->ops->hw_reset(host);
|
|
|
|
mmc_host_clk_release(host);
|
|
|
|
}
|
|
|
|
|
2015-01-12 14:38:04 +00:00
|
|
|
int mmc_hw_reset(struct mmc_host *host)
|
2011-08-29 13:42:11 +00:00
|
|
|
{
|
2015-01-12 14:38:05 +00:00
|
|
|
int ret;
|
2011-08-29 13:42:11 +00:00
|
|
|
|
2015-01-12 14:38:05 +00:00
|
|
|
if (!host->card)
|
2011-08-29 13:42:11 +00:00
|
|
|
return -EINVAL;
|
|
|
|
|
2015-01-12 14:38:05 +00:00
|
|
|
mmc_bus_get(host);
|
|
|
|
if (!host->bus_ops || host->bus_dead || !host->bus_ops->reset) {
|
|
|
|
mmc_bus_put(host);
|
2011-08-29 13:42:11 +00:00
|
|
|
return -EOPNOTSUPP;
|
|
|
|
}
|
|
|
|
|
2015-01-12 14:38:05 +00:00
|
|
|
ret = host->bus_ops->reset(host);
|
|
|
|
mmc_bus_put(host);
|
2011-08-29 13:42:11 +00:00
|
|
|
|
2015-05-07 10:10:25 +00:00
|
|
|
if (ret != -EOPNOTSUPP)
|
|
|
|
pr_warn("%s: tried to reset card\n", mmc_hostname(host));
|
2011-08-29 13:42:11 +00:00
|
|
|
|
2015-01-12 14:38:05 +00:00
|
|
|
return ret;
|
2011-08-29 13:42:11 +00:00
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_hw_reset);
|
|
|
|
|
2011-01-03 18:36:56 +00:00
|
|
|
static int mmc_rescan_try_freq(struct mmc_host *host, unsigned freq)
|
|
|
|
{
|
|
|
|
host->f_init = freq;
|
|
|
|
|
|
|
|
#ifdef CONFIG_MMC_DEBUG
|
|
|
|
pr_info("%s: %s: trying to init card at %u Hz\n",
|
|
|
|
mmc_hostname(host), __func__, host->f_init);
|
|
|
|
#endif
|
2013-09-12 12:36:53 +00:00
|
|
|
mmc_power_up(host, host->ocr_avail);
|
2011-02-14 07:12:28 +00:00
|
|
|
|
2011-08-29 13:42:11 +00:00
|
|
|
/*
|
|
|
|
* Some eMMCs (with VCCQ always on) may not be reset after power up, so
|
|
|
|
* do a hardware reset if possible.
|
|
|
|
*/
|
|
|
|
mmc_hw_reset_for_init(host);
|
|
|
|
|
2011-02-14 07:12:28 +00:00
|
|
|
/*
|
|
|
|
* sdio_reset sends CMD52 to reset card. Since we do not know
|
|
|
|
* if the card is being re-initialized, just send it. CMD52
|
|
|
|
* should be ignored by SD/eMMC cards.
|
|
|
|
*/
|
2011-01-03 18:36:56 +00:00
|
|
|
sdio_reset(host);
|
|
|
|
mmc_go_idle(host);
|
|
|
|
|
|
|
|
mmc_send_if_cond(host, host->ocr_avail);
|
|
|
|
|
|
|
|
/* Order's important: probe SDIO, then SD, then MMC */
|
|
|
|
if (!mmc_attach_sdio(host))
|
|
|
|
return 0;
|
|
|
|
if (!mmc_attach_sd(host))
|
|
|
|
return 0;
|
|
|
|
if (!mmc_attach_mmc(host))
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
mmc_power_off(host);
|
|
|
|
return -EIO;
|
|
|
|
}
|
|
|
|
|
2011-11-28 14:22:00 +00:00
|
|
|
int _mmc_detect_card_removed(struct mmc_host *host)
|
|
|
|
{
|
|
|
|
int ret;
|
|
|
|
|
2013-10-30 22:15:30 +00:00
|
|
|
if (host->caps & MMC_CAP_NONREMOVABLE)
|
2011-11-28 14:22:00 +00:00
|
|
|
return 0;
|
|
|
|
|
|
|
|
if (!host->card || mmc_card_removed(host->card))
|
|
|
|
return 1;
|
|
|
|
|
|
|
|
ret = host->bus_ops->alive(host);
|
2013-02-28 07:29:29 +00:00
|
|
|
|
|
|
|
/*
|
|
|
|
* Card detect status and alive check may be out of sync if card is
|
|
|
|
* removed slowly, when card detect switch changes while card/slot
|
|
|
|
* pads are still contacted in hardware (refer to "SD Card Mechanical
|
|
|
|
* Addendum, Appendix C: Card Detection Switch"). So reschedule a
|
|
|
|
* detect work 200ms later for this case.
|
|
|
|
*/
|
|
|
|
if (!ret && host->ops->get_cd && !host->ops->get_cd(host)) {
|
|
|
|
mmc_detect_change(host, msecs_to_jiffies(200));
|
|
|
|
pr_debug("%s: card removed too slowly\n", mmc_hostname(host));
|
|
|
|
}
|
|
|
|
|
2011-11-28 14:22:00 +00:00
|
|
|
if (ret) {
|
|
|
|
mmc_card_set_removed(host->card);
|
|
|
|
pr_debug("%s: card remove detected\n", mmc_hostname(host));
|
|
|
|
}
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
int mmc_detect_card_removed(struct mmc_host *host)
|
|
|
|
{
|
|
|
|
struct mmc_card *card = host->card;
|
2012-02-06 09:42:39 +00:00
|
|
|
int ret;
|
2011-11-28 14:22:00 +00:00
|
|
|
|
|
|
|
WARN_ON(!host->claimed);
|
2012-02-06 09:42:39 +00:00
|
|
|
|
|
|
|
if (!card)
|
|
|
|
return 1;
|
|
|
|
|
|
|
|
ret = mmc_card_removed(card);
|
2011-11-28 14:22:00 +00:00
|
|
|
/*
|
|
|
|
* The card will be considered unchanged unless we have been asked to
|
|
|
|
* detect a change or host requires polling to provide card detection.
|
|
|
|
*/
|
2013-04-18 09:02:07 +00:00
|
|
|
if (!host->detect_change && !(host->caps & MMC_CAP_NEEDS_POLL))
|
2012-02-06 09:42:39 +00:00
|
|
|
return ret;
|
2011-11-28 14:22:00 +00:00
|
|
|
|
|
|
|
host->detect_change = 0;
|
2012-02-06 09:42:39 +00:00
|
|
|
if (!ret) {
|
|
|
|
ret = _mmc_detect_card_removed(host);
|
2013-04-18 09:02:07 +00:00
|
|
|
if (ret && (host->caps & MMC_CAP_NEEDS_POLL)) {
|
2012-02-06 09:42:39 +00:00
|
|
|
/*
|
|
|
|
* Schedule a detect work as soon as possible to let a
|
|
|
|
* rescan handle the card removal.
|
|
|
|
*/
|
|
|
|
cancel_delayed_work(&host->detect);
|
2013-09-20 09:02:35 +00:00
|
|
|
_mmc_detect_change(host, 0, false);
|
2012-02-06 09:42:39 +00:00
|
|
|
}
|
|
|
|
}
|
2011-11-28 14:22:00 +00:00
|
|
|
|
2012-02-06 09:42:39 +00:00
|
|
|
return ret;
|
2011-11-28 14:22:00 +00:00
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_detect_card_removed);
|
|
|
|
|
2007-05-19 12:06:24 +00:00
|
|
|
void mmc_rescan(struct work_struct *work)
|
2005-04-16 22:20:36 +00:00
|
|
|
{
|
2006-11-22 14:57:56 +00:00
|
|
|
struct mmc_host *host =
|
|
|
|
container_of(work, struct mmc_host, detect.work);
|
2010-09-06 01:37:19 +00:00
|
|
|
int i;
|
mmc: fix all hangs related to mmc/sd card insert/removal during suspend/resume
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 01:01:41 +00:00
|
|
|
|
2014-04-08 22:19:43 +00:00
|
|
|
if (host->trigger_card_event && host->ops->card_event) {
|
|
|
|
host->ops->card_event(host);
|
|
|
|
host->trigger_card_event = false;
|
|
|
|
}
|
|
|
|
|
2011-01-03 18:36:56 +00:00
|
|
|
if (host->rescan_disable)
|
mmc: fix all hangs related to mmc/sd card insert/removal during suspend/resume
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 01:01:41 +00:00
|
|
|
return;
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2012-08-23 11:40:55 +00:00
|
|
|
/* If there is a non-removable card registered, only scan once */
|
|
|
|
if ((host->caps & MMC_CAP_NONREMOVABLE) && host->rescan_entered)
|
|
|
|
return;
|
|
|
|
host->rescan_entered = 1;
|
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
mmc_bus_get(host);
|
2007-01-03 18:47:29 +00:00
|
|
|
|
2010-11-28 05:21:28 +00:00
|
|
|
/*
|
|
|
|
* if there is a _removable_ card registered, check whether it is
|
|
|
|
* still present
|
|
|
|
*/
|
2013-10-30 22:15:30 +00:00
|
|
|
if (host->bus_ops && !host->bus_dead
|
2011-03-08 21:32:02 +00:00
|
|
|
&& !(host->caps & MMC_CAP_NONREMOVABLE))
|
2009-03-31 14:51:21 +00:00
|
|
|
host->bus_ops->detect(host);
|
|
|
|
|
2011-11-28 14:22:00 +00:00
|
|
|
host->detect_change = 0;
|
|
|
|
|
2011-01-04 17:20:22 +00:00
|
|
|
/*
|
|
|
|
* Let mmc_bus_put() free the bus/bus_ops if we've found that
|
|
|
|
* the card is no longer present.
|
|
|
|
*/
|
2009-03-31 14:51:21 +00:00
|
|
|
mmc_bus_put(host);
|
|
|
|
mmc_bus_get(host);
|
|
|
|
|
|
|
|
/* if there still is a card present, stop here */
|
|
|
|
if (host->bus_ops != NULL) {
|
2006-12-30 23:11:32 +00:00
|
|
|
mmc_bus_put(host);
|
2009-03-31 14:51:21 +00:00
|
|
|
goto out;
|
|
|
|
}
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2009-03-31 14:51:21 +00:00
|
|
|
/*
|
|
|
|
* Only we can add a new handler, so it's safe to
|
|
|
|
* release the lock here.
|
|
|
|
*/
|
|
|
|
mmc_bus_put(host);
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2013-12-05 13:34:46 +00:00
|
|
|
if (!(host->caps & MMC_CAP_NONREMOVABLE) && host->ops->get_cd &&
|
|
|
|
host->ops->get_cd(host) == 0) {
|
2012-05-09 14:15:26 +00:00
|
|
|
mmc_claim_host(host);
|
|
|
|
mmc_power_off(host);
|
|
|
|
mmc_release_host(host);
|
2009-03-31 14:51:21 +00:00
|
|
|
goto out;
|
2012-05-09 14:15:26 +00:00
|
|
|
}
|
2005-04-16 22:20:36 +00:00
|
|
|
|
2011-01-03 18:36:56 +00:00
|
|
|
mmc_claim_host(host);
|
2010-09-06 01:37:19 +00:00
|
|
|
for (i = 0; i < ARRAY_SIZE(freqs); i++) {
|
2011-01-03 18:36:56 +00:00
|
|
|
if (!mmc_rescan_try_freq(host, max(freqs[i], host->f_min)))
|
|
|
|
break;
|
2011-05-12 08:18:59 +00:00
|
|
|
if (freqs[i] <= host->f_min)
|
2011-01-03 18:36:56 +00:00
|
|
|
break;
|
2010-09-06 01:37:19 +00:00
|
|
|
}
|
2011-01-03 18:36:56 +00:00
|
|
|
mmc_release_host(host);
|
|
|
|
|
|
|
|
out:
|
2008-06-17 14:17:15 +00:00
|
|
|
if (host->caps & MMC_CAP_NEEDS_POLL)
|
|
|
|
mmc_schedule_delayed_work(&host->detect, HZ);
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
|
|
|
|
2007-05-19 12:06:24 +00:00
|
|
|
void mmc_start_host(struct mmc_host *host)
|
2005-04-16 22:20:36 +00:00
|
|
|
{
|
2012-05-09 14:15:26 +00:00
|
|
|
host->f_init = max(freqs[0], host->f_min);
|
2012-06-14 08:17:39 +00:00
|
|
|
host->rescan_disable = 0;
|
2014-09-24 09:07:13 +00:00
|
|
|
host->ios.power_mode = MMC_POWER_UNDEFINED;
|
2013-04-15 15:27:25 +00:00
|
|
|
if (host->caps2 & MMC_CAP2_NO_PRESCAN_POWERUP)
|
|
|
|
mmc_power_off(host);
|
|
|
|
else
|
2013-09-12 12:36:53 +00:00
|
|
|
mmc_power_up(host, host->ocr_avail);
|
2014-03-10 13:02:41 +00:00
|
|
|
mmc_gpiod_request_cd_irq(host);
|
2013-09-20 09:02:35 +00:00
|
|
|
_mmc_detect_change(host, 0, false);
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
|
|
|
|
2007-05-19 12:06:24 +00:00
|
|
|
void mmc_stop_host(struct mmc_host *host)
|
2005-04-16 22:20:36 +00:00
|
|
|
{
|
2007-02-11 19:43:19 +00:00
|
|
|
#ifdef CONFIG_MMC_DEBUG
|
2007-05-08 20:35:17 +00:00
|
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
2007-02-11 19:43:19 +00:00
|
|
|
host->removed = 1;
|
2007-05-08 20:35:17 +00:00
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
2007-02-11 19:43:19 +00:00
|
|
|
#endif
|
2014-03-10 13:02:41 +00:00
|
|
|
if (host->slot.cd_irq >= 0)
|
|
|
|
disable_irq(host->slot.cd_irq);
|
2007-02-11 19:43:19 +00:00
|
|
|
|
2012-06-14 08:17:39 +00:00
|
|
|
host->rescan_disable = 1;
|
2010-11-11 16:32:25 +00:00
|
|
|
cancel_delayed_work_sync(&host->detect);
|
2007-02-11 19:43:19 +00:00
|
|
|
mmc_flush_scheduled_work();
|
|
|
|
|
2010-03-05 21:43:31 +00:00
|
|
|
/* clear pm flags now and let card drivers set them as needed */
|
|
|
|
host->pm_flags = 0;
|
|
|
|
|
2006-12-30 23:11:32 +00:00
|
|
|
mmc_bus_get(host);
|
|
|
|
if (host->bus_ops && !host->bus_dead) {
|
2012-01-04 14:28:45 +00:00
|
|
|
/* Calling bus_ops->remove() with a claimed host can deadlock */
|
2013-06-10 15:03:36 +00:00
|
|
|
host->bus_ops->remove(host);
|
2006-12-30 23:11:32 +00:00
|
|
|
mmc_claim_host(host);
|
|
|
|
mmc_detach_bus(host);
|
2011-09-21 18:08:13 +00:00
|
|
|
mmc_power_off(host);
|
2006-12-30 23:11:32 +00:00
|
|
|
mmc_release_host(host);
|
2009-09-22 23:44:36 +00:00
|
|
|
mmc_bus_put(host);
|
|
|
|
return;
|
2005-04-16 22:20:36 +00:00
|
|
|
}
|
2006-12-30 23:11:32 +00:00
|
|
|
mmc_bus_put(host);
|
|
|
|
|
|
|
|
BUG_ON(host->card);
|
2005-04-16 22:20:36 +00:00
|
|
|
|
|
|
|
mmc_power_off(host);
|
|
|
|
}
|
|
|
|
|
2010-10-02 11:54:06 +00:00
|
|
|
int mmc_power_save_host(struct mmc_host *host)
|
2009-09-22 23:44:33 +00:00
|
|
|
{
|
2010-10-02 11:54:06 +00:00
|
|
|
int ret = 0;
|
|
|
|
|
2011-07-17 15:38:41 +00:00
|
|
|
#ifdef CONFIG_MMC_DEBUG
|
|
|
|
pr_info("%s: %s: powering down\n", mmc_hostname(host), __func__);
|
|
|
|
#endif
|
|
|
|
|
2009-09-22 23:44:33 +00:00
|
|
|
mmc_bus_get(host);
|
|
|
|
|
2013-10-30 22:15:30 +00:00
|
|
|
if (!host->bus_ops || host->bus_dead) {
|
2009-09-22 23:44:33 +00:00
|
|
|
mmc_bus_put(host);
|
2010-10-02 11:54:06 +00:00
|
|
|
return -EINVAL;
|
2009-09-22 23:44:33 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
if (host->bus_ops->power_save)
|
2010-10-02 11:54:06 +00:00
|
|
|
ret = host->bus_ops->power_save(host);
|
2009-09-22 23:44:33 +00:00
|
|
|
|
|
|
|
mmc_bus_put(host);
|
|
|
|
|
|
|
|
mmc_power_off(host);
|
2010-10-02 11:54:06 +00:00
|
|
|
|
|
|
|
return ret;
|
2009-09-22 23:44:33 +00:00
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_power_save_host);
|
|
|
|
|
2010-10-02 11:54:06 +00:00
|
|
|
int mmc_power_restore_host(struct mmc_host *host)
|
2009-09-22 23:44:33 +00:00
|
|
|
{
|
2010-10-02 11:54:06 +00:00
|
|
|
int ret;
|
|
|
|
|
2011-07-17 15:38:41 +00:00
|
|
|
#ifdef CONFIG_MMC_DEBUG
|
|
|
|
pr_info("%s: %s: powering up\n", mmc_hostname(host), __func__);
|
|
|
|
#endif
|
|
|
|
|
2009-09-22 23:44:33 +00:00
|
|
|
mmc_bus_get(host);
|
|
|
|
|
2013-10-30 22:15:30 +00:00
|
|
|
if (!host->bus_ops || host->bus_dead) {
|
2009-09-22 23:44:33 +00:00
|
|
|
mmc_bus_put(host);
|
2010-10-02 11:54:06 +00:00
|
|
|
return -EINVAL;
|
2009-09-22 23:44:33 +00:00
|
|
|
}
|
|
|
|
|
2013-09-13 09:31:33 +00:00
|
|
|
mmc_power_up(host, host->card->ocr);
|
2010-10-02 11:54:06 +00:00
|
|
|
ret = host->bus_ops->power_restore(host);
|
2009-09-22 23:44:33 +00:00
|
|
|
|
|
|
|
mmc_bus_put(host);
|
2010-10-02 11:54:06 +00:00
|
|
|
|
|
|
|
return ret;
|
2009-09-22 23:44:33 +00:00
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_power_restore_host);
|
|
|
|
|
2011-10-14 05:03:21 +00:00
|
|
|
/*
|
|
|
|
* Flush the cache to the non-volatile storage.
|
|
|
|
*/
|
|
|
|
int mmc_flush_cache(struct mmc_card *card)
|
|
|
|
{
|
|
|
|
int err = 0;
|
|
|
|
|
|
|
|
if (mmc_card_mmc(card) &&
|
|
|
|
(card->ext_csd.cache_size > 0) &&
|
|
|
|
(card->ext_csd.cache_ctrl & 1)) {
|
|
|
|
err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
|
|
|
|
EXT_CSD_FLUSH_CACHE, 1, 0);
|
|
|
|
if (err)
|
|
|
|
pr_err("%s: cache flush error %d\n",
|
|
|
|
mmc_hostname(card->host), err);
|
|
|
|
}
|
|
|
|
|
|
|
|
return err;
|
|
|
|
}
|
|
|
|
EXPORT_SYMBOL(mmc_flush_cache);
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
#ifdef CONFIG_PM
|
|
|
|
|
mmc: fix all hangs related to mmc/sd card insert/removal during suspend/resume
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 01:01:41 +00:00
|
|
|
/* Do the card removal on suspend if card is assumed removeable
|
|
|
|
* Do that in pm notifier while userspace isn't yet frozen, so we will be able
|
|
|
|
to sync the card.
|
|
|
|
*/
|
|
|
|
int mmc_pm_notify(struct notifier_block *notify_block,
|
|
|
|
unsigned long mode, void *unused)
|
|
|
|
{
|
|
|
|
struct mmc_host *host = container_of(
|
|
|
|
notify_block, struct mmc_host, pm_notify);
|
|
|
|
unsigned long flags;
|
2013-06-10 15:03:37 +00:00
|
|
|
int err = 0;
|
mmc: fix all hangs related to mmc/sd card insert/removal during suspend/resume
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 01:01:41 +00:00
|
|
|
|
|
|
|
switch (mode) {
|
|
|
|
case PM_HIBERNATION_PREPARE:
|
|
|
|
case PM_SUSPEND_PREPARE:
|
2015-04-23 10:43:43 +00:00
|
|
|
case PM_RESTORE_PREPARE:
|
mmc: fix all hangs related to mmc/sd card insert/removal during suspend/resume
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 01:01:41 +00:00
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
|
|
|
host->rescan_disable = 1;
|
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
|
|
|
cancel_delayed_work_sync(&host->detect);
|
|
|
|
|
2013-06-10 15:03:37 +00:00
|
|
|
if (!host->bus_ops)
|
|
|
|
break;
|
|
|
|
|
|
|
|
/* Validate prerequisites for suspend */
|
|
|
|
if (host->bus_ops->pre_suspend)
|
|
|
|
err = host->bus_ops->pre_suspend(host);
|
2013-10-30 22:15:30 +00:00
|
|
|
if (!err)
|
mmc: fix all hangs related to mmc/sd card insert/removal during suspend/resume
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 01:01:41 +00:00
|
|
|
break;
|
|
|
|
|
2012-01-04 14:28:45 +00:00
|
|
|
/* Calling bus_ops->remove() with a claimed host can deadlock */
|
2013-06-10 15:03:36 +00:00
|
|
|
host->bus_ops->remove(host);
|
2012-01-04 14:28:45 +00:00
|
|
|
mmc_claim_host(host);
|
mmc: fix all hangs related to mmc/sd card insert/removal during suspend/resume
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 01:01:41 +00:00
|
|
|
mmc_detach_bus(host);
|
2011-09-21 18:08:13 +00:00
|
|
|
mmc_power_off(host);
|
mmc: fix all hangs related to mmc/sd card insert/removal during suspend/resume
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 01:01:41 +00:00
|
|
|
mmc_release_host(host);
|
|
|
|
host->pm_flags = 0;
|
|
|
|
break;
|
|
|
|
|
|
|
|
case PM_POST_SUSPEND:
|
|
|
|
case PM_POST_HIBERNATION:
|
2010-12-10 07:40:31 +00:00
|
|
|
case PM_POST_RESTORE:
|
mmc: fix all hangs related to mmc/sd card insert/removal during suspend/resume
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 01:01:41 +00:00
|
|
|
|
|
|
|
spin_lock_irqsave(&host->lock, flags);
|
|
|
|
host->rescan_disable = 0;
|
|
|
|
spin_unlock_irqrestore(&host->lock, flags);
|
2013-09-20 09:02:35 +00:00
|
|
|
_mmc_detect_change(host, 0, false);
|
mmc: fix all hangs related to mmc/sd card insert/removal during suspend/resume
If you don't use CONFIG_MMC_UNSAFE_RESUME, as soon as you attempt to
suspend, the card will be removed, therefore this patch doesn't change the
behavior of this option.
However the removal will be done by pm notifier, which runs while
userspace is still not frozen and thus can freely use del_gendisk, without
the risk of deadlock which would happen otherwise.
Card detect workqueue is now disabled while userspace is frozen, Therefore
if you do use CONFIG_MMC_UNSAFE_RESUME, and remove the card during
suspend, the removal will be detected as soon as userspace is unfrozen,
again at the moment it is safe to call del_gendisk.
Tested with and without CONFIG_MMC_UNSAFE_RESUME with suspend and hibernate.
[akpm@linux-foundation.org: clean up function prototype]
[akpm@linux-foundation.org: fix CONFIG_PM-n linkage, small cleanups]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 01:01:41 +00:00
|
|
|
|
|
|
|
}
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
2005-04-16 22:20:36 +00:00
|
|
|
#endif
|
|
|
|
|
2013-01-14 19:28:17 +00:00
|
|
|
/**
|
|
|
|
* mmc_init_context_info() - init synchronization context
|
|
|
|
* @host: mmc host
|
|
|
|
*
|
|
|
|
* Init struct context_info needed to implement asynchronous
|
|
|
|
* request mechanism, used by mmc core, host driver and mmc requests
|
|
|
|
* supplier.
|
|
|
|
*/
|
|
|
|
void mmc_init_context_info(struct mmc_host *host)
|
|
|
|
{
|
|
|
|
spin_lock_init(&host->context_info.lock);
|
|
|
|
host->context_info.is_new_req = false;
|
|
|
|
host->context_info.is_done_rcv = false;
|
|
|
|
host->context_info.is_waiting_last_req = false;
|
|
|
|
init_waitqueue_head(&host->context_info.wait);
|
|
|
|
}
|
|
|
|
|
2007-05-19 12:32:22 +00:00
|
|
|
static int __init mmc_init(void)
|
|
|
|
{
|
|
|
|
int ret;
|
|
|
|
|
2010-12-24 15:00:17 +00:00
|
|
|
workqueue = alloc_ordered_workqueue("kmmcd", 0);
|
2007-05-19 12:32:22 +00:00
|
|
|
if (!workqueue)
|
|
|
|
return -ENOMEM;
|
|
|
|
|
|
|
|
ret = mmc_register_bus();
|
2007-05-26 11:48:18 +00:00
|
|
|
if (ret)
|
|
|
|
goto destroy_workqueue;
|
|
|
|
|
|
|
|
ret = mmc_register_host_class();
|
|
|
|
if (ret)
|
|
|
|
goto unregister_bus;
|
|
|
|
|
|
|
|
ret = sdio_register_bus();
|
|
|
|
if (ret)
|
|
|
|
goto unregister_host_class;
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
unregister_host_class:
|
|
|
|
mmc_unregister_host_class();
|
|
|
|
unregister_bus:
|
|
|
|
mmc_unregister_bus();
|
|
|
|
destroy_workqueue:
|
|
|
|
destroy_workqueue(workqueue);
|
|
|
|
|
2007-05-19 12:32:22 +00:00
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static void __exit mmc_exit(void)
|
|
|
|
{
|
2007-05-26 11:48:18 +00:00
|
|
|
sdio_unregister_bus();
|
2007-05-19 12:32:22 +00:00
|
|
|
mmc_unregister_host_class();
|
|
|
|
mmc_unregister_bus();
|
|
|
|
destroy_workqueue(workqueue);
|
|
|
|
}
|
|
|
|
|
2007-06-16 06:07:53 +00:00
|
|
|
subsys_initcall(mmc_init);
|
2007-05-19 12:32:22 +00:00
|
|
|
module_exit(mmc_exit);
|
|
|
|
|
2005-04-16 22:20:36 +00:00
|
|
|
MODULE_LICENSE("GPL");
|