mirror of
https://github.com/torvalds/linux.git
synced 2024-12-23 03:11:46 +00:00
2a500afe1e
With a flash-based BBT there is no reason to move the Factory Bad Block Marker from the data area buffer (to where it is mapped by the GPMI NAND controller) to the OOB buffer. Thus, make this feature configurable via DT. This is required for the Ka-Ro electronics platforms. In the original code 'this->swap_block_mark' was synonymous with '!GPMI_IS_MX23()', so use the latter at the relevant places. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Acked-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
59 lines
2.3 KiB
Plaintext
59 lines
2.3 KiB
Plaintext
* Freescale General-Purpose Media Interface (GPMI)
|
|
|
|
The GPMI nand controller provides an interface to control the
|
|
NAND flash chips. We support only one NAND chip now.
|
|
|
|
Required properties:
|
|
- compatible : should be "fsl,<chip>-gpmi-nand"
|
|
- reg : should contain registers location and length for gpmi and bch.
|
|
- reg-names: Should contain the reg names "gpmi-nand" and "bch"
|
|
- interrupts : BCH interrupt number.
|
|
- interrupt-names : Should be "bch".
|
|
- dmas: DMA specifier, consisting of a phandle to DMA controller node
|
|
and GPMI DMA channel ID.
|
|
Refer to dma.txt and fsl-mxs-dma.txt for details.
|
|
- dma-names: Must be "rx-tx".
|
|
|
|
Optional properties:
|
|
- nand-on-flash-bbt: boolean to enable on flash bbt option if not
|
|
present false
|
|
- fsl,use-minimum-ecc: Protect this NAND flash with the minimum ECC
|
|
strength required. The required ECC strength is
|
|
automatically discoverable for some flash
|
|
(e.g., according to the ONFI standard).
|
|
However, note that if this strength is not
|
|
discoverable or this property is not enabled,
|
|
the software may chooses an implementation-defined
|
|
ECC scheme.
|
|
- fsl,no-blockmark-swap: Don't swap the bad block marker from the OOB
|
|
area with the byte in the data area but rely on the
|
|
flash based BBT for identifying bad blocks.
|
|
NOTE: this is only valid in conjunction with
|
|
'nand-on-flash-bbt'.
|
|
WARNING: on i.MX28 blockmark swapping cannot be
|
|
disabled for the BootROM in the FCB. Thus,
|
|
partitions written from Linux with this feature
|
|
turned on may not be accessible by the BootROM
|
|
code.
|
|
|
|
The device tree may optionally contain sub-nodes describing partitions of the
|
|
address space. See partition.txt for more detail.
|
|
|
|
Examples:
|
|
|
|
gpmi-nand@8000c000 {
|
|
compatible = "fsl,imx28-gpmi-nand";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
reg = <0x8000c000 2000>, <0x8000a000 2000>;
|
|
reg-names = "gpmi-nand", "bch";
|
|
interrupts = <41>;
|
|
interrupt-names = "bch";
|
|
dmas = <&dma_apbh 4>;
|
|
dma-names = "rx-tx";
|
|
|
|
partition@0 {
|
|
...
|
|
};
|
|
};
|